BMC BMC Training Presentation.
-
Upload
edith-wagstaff -
Category
Documents
-
view
245 -
download
6
Transcript of BMC BMC Training Presentation.
BMC
www.Broad-Machinery.com
BMC
Training PresentationTraining Presentation
BMC
www.Broad-Machinery.com
BMC
UNDERCARRIAGE SYSTEMUNDERCARRIAGE SYSTEM
Component AssemblyComponent Assembly
Operation PrinciplesOperation Principles
BMC
www.Broad-Machinery.com
BMCBulldozer AssemblyBulldozer Assembly
Power Take-offPower Take-offTorque ConverterTorque ConverterUniversal JointUniversal JointTransmission UnitTransmission UnitMain DriveMain DriveSteering ClutchSteering ClutchSteering BrakeSteering BrakeFinal DriveFinal DriveTrack EquipmentTrack EquipmentControl SystemControl SystemWorking EquipmentWorking EquipmentCabinCabinFloor & FenderFloor & FenderTrack FrameTrack Frame
BMC
www.Broad-Machinery.com
BMC Engine
Torque Converter
Universal Joint
Gear Box
Main Drive
Steering Clutch
Final Drive
Track System
Power TrainPower Train
BMC
www.Broad-Machinery.com
BMCFunction:Function: PTO power
Equipment:Equipment:
Work system pump
Transmission pump
Steering Pump
Power Take-offPower Take-off
BMC
www.Broad-Machinery.com
BMC• Type:
3-element
1 stage
1 phase• Assembly: Pump,
Turbine and Stator• There are many
vanes on these components for using oil to transfer power
Torque ConverterTorque Converter Assembly Assembly
BMC
www.Broad-Machinery.com
BMC• These 3 components
combined with oil, give us as smooth power transmission.
• Safety valve: fitted to oil input, ensures the input oil pressure is no more than 0.87MPa.
• Relief Valve: fitted on oil output, ensures the oil pressure inside the torque converter is maintained below 0.45MPa.
BMC
www.Broad-Machinery.com
BMC
BMC
www.Broad-Machinery.com
BMC• Oil Flow: Pump→ Turbine
→ Stator→ pump• There is 2 mm clearance
between pump and Turbine, and transfers power by Oil. There is no mechanical impact, they protect each other
• Assist hydraulic system: to resist loss of oil; to maintain the normal oil temperature.
Principles of Principles of Torque ConverterTorque Converter
BMC
www.Broad-Machinery.com
BMC• When the load
increases, the dozer ground speed is reduced, causing turbine speed to slow down. But at this time the energy from the pump transfer to torque converter is not reduced. This energy is still transferring to the stator through the slowing turbine. Then the energy to stator from turbine, results in the turbine gaining torque, then the turbine output torque is increasing.
Operation of Operation of Torque ConverterTorque Converter
BMC
www.Broad-Machinery.com
BMC1.Change torque
automatically
2.Absorb vibration, prolong working life
3.Good power transmission capability, driving at slow speed
4.Simple operation
5. Start smoothly, eliminates any shocks in power train
6.Easy maintenance
Torque ConverterTorque Converter Operation Operation
BMC
www.Broad-Machinery.com
BMC Normally, SD22 Torque Converter Temperature of
output oil is 115-120oC. For a short time, a higher temperature of 130-135oC is allowed, but long term high temperature shows there is something wrong, for the following reasons:
1.1.Shortage of OilShortage of Oil Torque converter, transmission, main drive, steering
and final drive will take 30% of engine rated power. This power will transfer to heat energy, and increase the oil temperature. Therefore it requires enough oil to absorb this heat.
If the oil quantity is not sufficient, the oil temperature will be too high.
High Torque Converter Oil TemperatureHigh Torque Converter Oil Temperature
BMC
www.Broad-Machinery.com
BMC2.Oil Pressure of input and output are incorrect2.Oil Pressure of input and output are incorrect If torque converter input oil pressure is not correct (Standard: 0.87MPa) or the oil is dirty, the piston of valve will stay at relief position, so the oil pressure to the torque converter is low. This leads to a loss of efficiency and excessive oil temperature.
If torque converter output oil pressure is not correct (Standard: 0.45MPa) or the oil supply is blocked, return oil temperature will be too high. The flow of oil to oil cooler is reduced, and the oil temperature too high
BMC
www.Broad-Machinery.com
BMC3. Incorrect Operation3. Incorrect Operation Excessive use of low engine speed for extended time, torque converter will work at low efficiency. Torque converter will lose power, and transfer heat energy leading to high oil temperature.
BMC
www.Broad-Machinery.com
BMC• The types of Transmission Case:
Base Operation type: 1.Manual Gearshift; 2.Hydraulic booster; 3.PowershiftBase Transmission type: 1.mechanical type; 2.Planetary Gear
• Planetary type powershift transmission case type: Planetary Gear, Multi-disc clutch, Hydraulic control, forced lubrication.
• Function: 1.Enable forward and reverse 2.Select different gear ratio 3.Matched with the torque converter, enables a wide range of power output and ground speed
Power Transmission CasePower Transmission Case
BMC
www.Broad-Machinery.com
BMCThe system consists of: A: Sun GearB: Planetary GearsC: Ring GearD: Carrier
The planetary gears are installed on the carrier being in constant mesh with the sun gear and the ring gear
Planetary Gear SystemPlanetary Gear System
A
B
C D
BMC
www.Broad-Machinery.com
BMCPlanetary Gear systemPlanetary Gear system
BMC
www.Broad-Machinery.com
BMCPrinciple of Planetary Gear systemPrinciple of Planetary Gear system
A: Sun GearB: Planetary GearC: Ring GearD: Carrier
If the carrier is fixed, the torque is transmitted from sun gear to planetary gear, and is transmitted from planetary gear to ring gear to make the ring gear rotate. Rotation direction of ring gear is opposite from sun gear.
BMC
www.Broad-Machinery.com
BMC
A: Sun GearB: Planetary GearC: Ring GearD: Carrier
If the ring gear is fixed, the torque is transmitted from sun gear to planetary gear. The planetary gear rotates by itself, at the same time rotates around sun gear. Rotation direction of the planetary gear shaft is opposite from sun gear.
It is a slowdown outfit that power input from sun gear, output from carrier
Principle of Planetary Gear systemPrinciple of Planetary Gear system
BMC
www.Broad-Machinery.com
BMC
The above principles are structure principle of No.1,3,4 planetary gear system.
The sun gear is active in No.1 Planetary Gear systemThe carrier is active in No.3 & 4 Planetary Gear system
BMC
www.Broad-Machinery.com
BMCThis is structure and principle of No.2 planetary gear system.
The rotate direction is contrary with No.1 planetary gear system.
BMC
www.Broad-Machinery.com
BMCSD22 powershift transmission systemSD22 powershift transmission system
Consists of 4 planetary gear systems with 4 clutches, and 1 locking clutch (no planetary gear system) and housing, input shaft, end gear and output bevel gear.
No.1 clutch is for Forward Gear No.2 clutch is for Reverse GearNo.3 clutch is for 3rd Gear ShiftNo.4 clutch is for 2nd Gear ShiftNo.5 lock clutch is for 1st Gear Shift
BMC
www.Broad-Machinery.com
BMC
BMC
www.Broad-Machinery.com
BMCThe 4 planetary gear system clutch’s washers and disc are the
same, but the disc quantity is different. Its design is based on transmission torque.
SD22 powershift transmission systemSD22 powershift transmission system
The No. of Clutch Washer Q’ty Disc Q’ty
No.1 3 4No.2 2 3No.3 1 2No.4 1 2No.5 2 3
BMC
www.Broad-Machinery.com
BMCNo.1- 4 planetary gear
systems’ structure are same, clutches’ washer and disc are same, but the disc quantity and piston is different.
BMC
www.Broad-Machinery.com
BMCMethod of fixing of each planetary gear is as this figure, it is actuated by the clutch.
EngagementEngagement of clutch is actuated by oil pressure from control valve pushing piston 3.
BMC
www.Broad-Machinery.com
BMCDisengagementDisengagement of clutch is actuated by return spring 33 which pushes piston 3 to original position after oil pressure is cut off.
The function of disc spring 42 is to improve operating speed of piston 3 and improve release the discs.
BMC
www.Broad-Machinery.com
BMCThis figure is a drawing of No.5 locking clutch. When the clutch disengages, oil in the cylinder body 16 by the action of centrifugal force. Disks can’t disengage quickly, only by disk spring 29. This can make the clutch half disengage. This will cause difficulty for next gearshift. In order to eliminate this problem, the ball check valve 17 is incorporated in the piston after the rotary clutch.
BMC
www.Broad-Machinery.com
BMCNo.5 Clutch is a lock No.5 Clutch is a lock clutch. clutch. When this clutch engages, pressure oil from controlling valve enters into oil cavity and pushes piston 26, at the same time, the oil pushes check valve ball 17 to plug the hole of valve. The clutch is engaged quickly.
BMC
www.Broad-Machinery.com
BMCNo.5 Clutch is a lock No.5 Clutch is a lock clutch. clutch. When the pressure oil from controlling valve is cut off, by the action of centrifugal force, ball 17 can move to the direction of arrow in this figure. At this time, the hole of valve cage is opened and the oil is drained off.
BMC
www.Broad-Machinery.com
BMCForward 1Forward 1stst Speed Speed
BMC
www.Broad-Machinery.com
BMCForward 2nd SpeedForward 2nd Speed
BMC
www.Broad-Machinery.com
BMCForward 3rd SpeedForward 3rd Speed
BMC
www.Broad-Machinery.com
BMCTransmission Lubrication and Transmission Lubrication and Cooling:Cooling:
It’s a forced lubrication system, from above and below, two ways divided through a valve.
Transmission Case lubrication pressure is 0.124Mpa. Upper way lubricates the second half bearing and cools the second half discs; lower way lubricates the first half bearing and cools first half discs.
BMC
www.Broad-Machinery.com
BMCMain Drive (SD22)• Assembly:Assembly: Bevel gears Horizontal Shaft Bearings Sprocket Hub
• Functions:Functions: Power train gear
reduction to increase the final drive torque
BMC
www.Broad-Machinery.com
BMC• Function:Function: To disengage the shaft
drive and control steering
• Type:Type:Wet, multi-disc, spring loaded, hydraulic separated, normally engaged.
• Spring forceSpring force F=3.2 tons
Steering Clutch
BMC
www.Broad-Machinery.com
BMCSteering Clutch Operation
BMC
www.Broad-Machinery.com
BMCSteering Brake
• Function:Function: The brake on the
outside of steering clutch’s outside drum, reduced the rpm of the final drive on that side.
• Type:Type:Wet band, hydraulic boosted control
BMC
www.Broad-Machinery.com
BMCSteering Brake Operation
Forward Reverse
BMC
www.Broad-Machinery.com
BMCLinkage through valvesLinkage through valves
Steering Brake Control
BMC
www.Broad-Machinery.com
BMC• There are 3 associated components, Main drive,
Steering Clutch and Steering Brake. They are lubricated and cooled by the oil in steering case. The oil level can be checked with oil dipstick
• Steering case has a breather to balance inside and outside pressures.
Steering Case Lubrication and Breather
BMC
www.Broad-Machinery.com
BMC• Final Drive: One Set
Final Drive on each side.
• 2 stage spur gears reduction. Floating Seal and O-ring to contain oil, then connected outside with breather.
• Assembling Sprocket hub and gear requires 60 tons force with special tools.
Final Drive
BMC
www.Broad-Machinery.com
BMC• Assembly:Assembly:
Track Frames
Track Rollers
Carrier Rollers
Recoil system
Track Shoes
Equalizer
Track System --- Walking Gear
BMC
www.Broad-Machinery.com
BMC• Function:Function:
1. Maintain track tension
2 absorb the vibration of idler
• Note:Note:
the fixed pressure is 20.38 tons, it requires special fitting tools
Recoil system for Track
BMC
www.Broad-Machinery.com
BMCuse a ruler placed on the track grousers between carrier roller and idler, the measure distance is C , C=20-30mm
SD32 track has more wide, the distance is bigger between carrier roller and idler, the measured distance is C=30-40mm
Measurement of Track Tension
Idler Carrier roller
BMC
www.Broad-Machinery.com
BMC• Function:Function:
Gives guidance for track chain and maintains track tension
• LubricationLubrication
There are lub oil in the cage that is sealed by floating seal, between idler and support housing. The oil capacity is 70%.
Idler
BMC
www.Broad-Machinery.com
BMC• If the clearance is over limit ,
the idler will swing, and track links off centre and will wear the sprocket.
• If Clearance in one sideA > 4mm, it must be adjusted into A=0.5-1mm
• If Clearance of up and down(B+C)≥5mm it must be adjusted into (B+C)=2mm 。
To Adjust Idler Clearance
BMC
www.Broad-Machinery.com
BMC• First it carries dozer
weight, secondly it prevent track chain moving off centre of track frame
• Bushing and float seal is similar to idler
Track Roller
BMC
www.Broad-Machinery.com
BMC• Supports all of the
dozer weight, and determines the ground pressure
• Four high strength bolts fix track shoe onto track link,
bolt torque:
SD16:70kg.m
SD22:76kg.m
SD32:100kg.m
Track Shoe Assembly
BMC
www.Broad-Machinery.com
BMCTrack supports 30 tons bulldozer weight, and if the working Track supports 30 tons bulldozer weight, and if the working conditions are bad, it will wear more quickly, so use and conditions are bad, it will wear more quickly, so use and maintain it correctly.maintain it correctly.
1. Often check the tension of track shoe. use a ruler put the track grousers between carrier roller and idler, the measure is C , C=20-30mm; SD32 track is more weight, the distance is more large between carrier roller and idler, the measure is C=30-40mm
When the work is hard, the track shoe ass’y will need to be adjust tighter; if the work is moderate , the track shoe ass’y tension can be adjusted back.
Use and Maintenance of Track Shoe
BMC
www.Broad-Machinery.com
BMC2. The sprocket segments need be replaced when the sprocket
segments wear under the limit.
3. Don’t drive dozer hard and avoid track damage and excessive wear.
4. If there is excessive track play and noise, you must stop and check tracks and machine.
5. When the dozer across the railway line, you must drive it across the railway at right angle, and don’t change speed, don’t stop and reverse, avoid track shoes locking in railway line.
7. After working, you must check tracks, and if there is something wrong. If there is something wrong, must repair or replace.
Use and Maintenance of Track Shoe
BMC
www.Broad-Machinery.com
BMCEnd of this Training Module
Thanks Your Cooperation !!!
End of this Training Module
Thanks Your Cooperation !!!