Data Sheet

Bluetooth Test SetMT8852B

2

IntroductionThis document provides specifications for the Bluetooth® Test Set MT8852B and lists ordering information and option and accessory codes.

The MT8852B brochure is also available. The brochure provides in-depth descriptions of MT8852B applications, features, and benefits when testing a wide range of Bluetooth products.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Anritsu is under license.

SpecificationsAll measurements made in compliance with Bluetooth Core Specification v5.1.

Basic Rate MeasurementsBasic Rate measurements made in compliance with Bluetooth RF Test Specification RF. TS. 5.1.0.

Output Power (RF/TRM/CA/BV-01-C)Measurement Configuration

Hopping: Off or On – measure at defined, all, or any frequencies Loopback or Tx mode Payload: PRBS9 Packet type: DH1, DH3, DH5

Displayed Results: Average power, Peak powerNumber of Measurement Frequencies: Three, default to RF Test Specification or user definedMeasurement Range: –50 to +22 dBm (average power), +23 dBm (peak power)Resolution: 0 .1 dBAccuracy: ±1.0 dB (–35 to +20 dBm), ±1.5 dB (+20 to +22 dBm)

Power Control (RF/TRM/CA/BV-03-C)Measurement Configuration

Hopping: Off Loopback or Tx mode Payload: PRBS9 Packet type: DH1, DH3, DH5

Displayed Result: Maximum power, Minimum power, Maximum step size, Minimum step size, Power at each power stepNumber of Measurement Frequencies: Three, default to RF Test Specification or user definedMeasurement Range: –35 to +22 dBm (average power), +23 dBm (peak power)Resolution: 0 .1 dBAccuracy: ±1.0 dB (–35 to +20 dBm), ±1.5 dB (+20 to +22 dBm)

Enhanced Power Control (RF/TRM/CA/BV-14-C)Measurement Configuration

Hopping: OffLoopback or Tx modePayload: PRBS9Packet type: DH1, DH3, DH5, 2-DH1, 2-DH3, 2-DH5, 3-DH1, 3-DH3 and 3-DH5

Displayed ResultMaximum power for each packet type, Minimum power for each packet type, Maximum power step for each packet type,Minimum power step for each packet type, Maximum power difference at any step between DHn and 2DHn or 3DHn packets

Number of Measurement Frequencies: Three, default to RF Test Specification or user definedMeasurement Range: –35 to +22 dBm (average power), +23 dBm (peak power)Resolution: 0 .1 dBAccuracy: ±1.0 dB (–35 to +20 dBm), ±1.5 dB (+20 to +22 dBm)

Initial Carrier Frequency Tolerance (RF/TRM/CA/BV-08-C)Measurement Configuration

Hopping: Off or On – measure at defined, all, or any frequencies Loopback or Tx mode Payload: PRBS9 Packet type: DH1

Displayed Results: Average initial frequency error, Maximum positive frequency error, Maximum negative frequency errorNumber of Measurement Frequencies: Three, default to RF Test Specification or user definedRF Input Measurement Range: – 35 to +20 dBmInitial Frequency Error Measurement Range: 0 to ±150 kHzFrequency Resolution: 1 kHzAccuracy: 500 Hz ±frequency standard

3

Carrier Frequency Drift (RF/TRM/CA/BV-09-C)Measurement Configuration

Hopping: Off or On – measure at defined, all, or any frequencies Loopback or Tx mode Payload: 10101010 Packet type: DH1, DH3, DH5

Displayed Results: Carrier frequency drift, Drift rateNumber of Measurement Frequencies: Three, default to RF Test Specification or user definedRF Input Measurement Range: –35 to +20 dBmFrequency Drift Measurement Range: 0 to 200 kHz, and >2000 µs/50 µsFrequency Resolution: 1 kHz

Sensitivity – single slot packets (RF/RCV/CA/BV-01-C)Measurement Configuration

Hopping: Off or On, user selectable Loopback only Payload: PRBS9 Packet type: DH1 Dirty transmitter (as defined in the RF test spec): On or Off, user defined

Displayed Results: BER (percentage), Total number of bit errors and FERNumber of Measurement Frequencies: Three, default to RF Test Specification or user definedNumber of Measured Bits: 1 to 10,000 packets (216 bits to 2,160,000 bits)Output Power Range: –90 to 0 dBm, resolution: 0 .1 dBOutput Power Accuracy: ±1 dB (–80 to 0 dBm)BER/FER Measurement Range: 0 to 100%BER/FER Resolution: 0 .001%

Sensitivity – multi-slot packets (RF/RCV/CA/BV-02-C)Measurement Configuration

Hopping: Off or On, user selectable Loopback only Payload: PRBS9 Packet type: DH3, DH5 Dirty transmitter (as defined in RF test spec): On or Off, user defined

Displayed Results: BER (percentage), Total number of bit errors and FERNumber of Measurement Frequencies: Three, default to RF Test Specification or user definedNumber of Measured Bits: 1 to 10,000 packets (for DH3, 1 ,464 bits to 14,640,000 bits), (for DH5, 2 ,712 bits to 27,120,000 bits)Output Power Range: –90 to 0 dBm, resolution: 0 .1 dBOutput Power Accuracy: ±1 dB (–80 to 0 dBm)BER/FER Measurement Range: 0 to 100%BER/FER Resolution: 0 .001%

Modulation Characteristics (RF/TRM/CA/BV-07-C)Measurement Configuration

Hopping: Off Loopback, Tx mode Payload: 11110000 and 10101010 Packet type: DH1, DH3, DH5

Displayed ResultsFrequency deviation: Δf1max, Δf2max, Δf1avg, Δf2avg, Δf2avg/Δf1avg, % of Δf2max <115 kHz

Number of Measurement Frequencies: Three, default to RF Test Specification or user definedRF Input Measurement Range: –35 to +20 dBmDeviation Measurement Range: 0 to 350 kHz (peak power)Deviation Resolution: 1 kHzAccuracy: 1% for modulation index 0.32

Maximum Input Level (RF/RCV/CA/BV-06-C)Measurement Configuration

Hopping: Off Loopback only Payload: PRBS9 Packet type: DH1

Displayed Results: BER (percentage), total number of bit errors and FERNumber of Measurement Frequencies: Three, default to RF Test Specification or user definedNumber of Measured Bits: 1 to 10,000 packets (216 bits to 2,160,000 bits)Output Power Range: –90 to 0 dBm, resolution: 0 .1 dBOutput Power Accuracy: ±1 dB (–80 to 0 dBm)

4

Enhanced Data Rate (EDR) MeasurementsEnhanced Data Rate measurements made in compliance with Bluetooth RF Test Specification RF. TS. 5.1.0.

EDR Relative Transmit Power (RF/TRM/CA/BV-10-C)Measurement Configuration

Hopping: Off and On – measure at defined, all, or any frequenciesModulations: π/4DQPSK and 8DPSK Packet type: 2-DH1, 2-DH3, 2-DH5, 3-DH1, 3-DH3 and 3-DH5 Loopback or Tx mode EUT power level: Max. and Min.

Displayed Results:Max. differential power (2-DH1, 2-DH3, 2-DH5 and 3-DH1, 3-DH3 and 3-DH5), Min. differential power (2-DH1, 2-DH3, 2-DH5 and 3-DH1, 3-DH3 and 3-DH5), average differential power (2-DH1, 2-DH3, 2-DH5 and 3-DH1, 3-DH3 and 3-DH5)

Number of Measurement Frequencies: Three, default to RF Test Specification or user definedMeasurement Range: –35 to +20 dBm (average power), +23 dBm (peak power)Relative Power Resolution: 0 .01 dB, GFSK to π/4DQPSK and 8DPSKRelative Power Accuracy

Relative power measurement accuracy between GFSK and π/4DQPSK or 8DPSK, 0 .2 dB typical for a power difference of <6 dBRelative Power Measurement Range

Relative power measurement range between GFSK and π/4DQPSK or 8DPSK, (PGFSK – 8 dB) < PDPSK < (PGFSK + 4 dB)

EDR Carrier Frequency Stability and Modulation Accuracy (RF/TRM/CA/BV-11-C)Measurement Configuration

Hopping: Off and On – measure at defined, all, or any frequenciesModulations: π/4DQPSK and 8DPSK Packet type: 2-DH1, 2-DH3, 2-DH5, 3-DH1, 3-DH3 and 3-DH5 Loopback or Tx mode EUT power level: Max. and Min.

Displayed Results: Initial frequency error ω i, Frequency error ωo, Frequency error ω i + ωo, RMS DEVM (block with greatest DEVM value displayed), Peak DEVM, 99% DEVM, Average RMS DEVM (average DEVM for all blocks measured)

Number of Measurement Frequencies: Three, default to RF Test Specification or user definedCarrier Frequency Stability Measurement Range: 0 to ±100 kHzCarrier Frequency Stability Accuracy: 500 Hz ±frequency standardCarrier Frequency Stability Resolution: 1 kHzRMS DEVM Range: 30% π/4DQPSK, 20% 8DPSKRMS DEVM Resolution: 0 .1% π/4DQPSK and 8DPSKPeak DEVM Range: 0 to 50% π/4DQPSK, 0 to 30% 8DPSKPeak DEVM Resolution: 0 .1% π/4DQPSK and 8DPSK

EDR Differential Phase Encoding (RF/TRM/CA/BV-12-C)Measurement Configuration

Hopping: Off and On, user selectableModulations: π/4DQPSK and 8DPSK Packet type: 2-DH1, 2-DH3, 2-DH5, 3-DH1, 3-DH3 and 3-DH5 Number of test packets: default 100 Tx mode only

Displayed Results: Number of packets received, Number of packets with payload data errors, Percentage of errored packetsNumber of Measurement Frequencies: Three, default to RF Test Specification or user defined

EDR Sensitivity (RF/RCV/CA/BV-07-C)Measurement Configuration

Hopping: Off and On, user selectableModulations: π/4DQPSK and 8DPSK Packet type: 2-DH1, 2-DH3, 2-DH5, 3-DH1, 3-DH3 and 3-DH5 Bit threshold control: Threshold 1, 1 .6 million bits, Threshold 2, 16 million bits (user editable) Loopback only Dirty transmitter (as defined in RF test spec): On or Off, user selectable

Displayed Results: Overall BER (displayed in exponential format), Number of bits in error, Number of packets sent by test set, Number of packets received in error by EUT

Number of Measurement Frequencies: Three, default to RF Test Specification or user definedOutput Power Range: –90 to 0 dBm, resolution: 0 .1 dBOutput Power Accuracy: ±1 dB (–80 to 0 dBm)

5

EDR BER Floor Performance (RF/RCV/CA/BV-08-C)Measurement Configuration

Hopping: Off and On, user selectableModulations: π/4DQPSK and 8DPSK Packet type: 2-DH1, 2-DH3, 2-DH5, 3-DH1, 3-DH3 and 3-DH5 Bit threshold control: Threshold 1, 8 million bits, Threshold 2, 160 million bits (user editable) Loopback only

Displayed Results: Overall BER (displayed in exponential format), Number of bits in error, Number of packets sent by test set, Number of packets received in error by EUT

Number of Measurement Frequencies: Three, default to RF Test Specification or user definedOutput Power Range: –90 to 0 dBm, resolution: 0 .1 dBOutput Power Accuracy: ±1 dB (–80 to 0 dBm)

EDR Maximum Input Level (RF/RCV/CA/BV-10-C)Measurement Configuration

Hopping: Off and On, user selectableModulations: π/4DQPSK and 8DPSK Packet type: 2-DH1, 2-DH3, 2-DH5, 3-DH1, 3-DH3 and 3-DH5 Number of bits: default 1 .6 million (user editable) Loopback only

Displayed Results: Overall BER (displayed in exponential format), Number of bits in error, Number of packets sent by test set, Number of packets received in error by EUT

Number of Measurement Frequencies: Three, default to RF Test Specification or user definedOutput Power Range: –90 to 0 dBm, resolution: 0 .1 dBOutput Power Accuracy: ±1 dB (–80 to 0 dBm)

Bluetooth low energy MeasurementsBluetooth low energy measurements made in compliance with Bluetooth RF Test Specification RF-PHY. TS. 5.1.0.

Output power (RF-PHY/TRM/BV-01-C, RF-PHY/TRM/BV-15-C)Measurement Configuration

EUT configured to transmit test reference packetsPacket payload: PRBS9AoA Constant Tone Extensions

Displayed Results: Average power, Peak to average powerNumber of Measurement Frequencies: Three, default to RF Test Specification or user definedMeasurement Range: –50 to +22 dBm (average power), +23 dBm (peak power)Resolution: 0 .1 dBAccuracy: ±1.0 dB (–35 to +20 dBm), ±1.5 dB (+20 to +22 dBm)

Modulation characteristics [RF-PHY/TRM/BV-05-C (BLE), RF-PHY/TRM/BV-10-C (2LE), RF-PHY/TRM/BV-13-C (BLR S = 8)]

Measurement ConfigurationEUT configured to transmit test reference packetsBLE/2LE Packet payload: 11110000 and 10101010BLE Packet payload: 11111111

Displayed ResultsFrequency deviation: ∆f1max, ∆f2max, ∆f1avg, ∆f2avg, ∆f2avg/∆f1avg comparison, % of ∆f2max < frequency deviation limit

Number of Measurement Frequencies: Three, default to RF Test Specification or user definedMeasurement Range

RF input: –35 to +20 dBmDeviation: 0 to 500 kHz (peak power)

ResolutionDeviation: 1 kHz

Accuracy: 1% for modulation index 0.5

Carrier frequency offset and drift [RF-PHY/TRM/BV-06-C (BLE), RF-PHY/TRM/BV-12-C (2LE), RF-PHY/TRM/BV-14-C (BLR S = 8), RF-PHY/TRM/BV-16-C (BLE CTE), RF-PHY/TRM/BV-17-C (2LE CTE)]

Measurement ConfigurationEUT configured to transmit test reference packetsBLE/2LE Packet payload: 10101010BLR Packet payload: 11111111BLE/2LE CTE Packet payload: 11110000AoA Constant Tone Extensions

Displayed Results: Carrier frequency error, Frequency drift, Drift rateNumber of Measurement Frequencies: Three, default to RF Test Specification or user definedMeasurement Range

RF input: –35 to +20 dBmFrequency: 500 kHz

Frequency Resolution: 1 kHzAccuracy: 500 Hz ±frequency standard

6

Receiver sensitivity [RF-PHY/RCV/BV-01-C (BLE), RF-PHY/RCV/BV-08-C (2LE), RF-PHY/RCV/BV-26-C (BLR S = 2), RF-PHY/RCV/BV-27-C (BLR S = 8)]

Measurement ConfigurationEUT configured to receive test reference packetsPacket payload: PRBS9Full support of dirty transmitter as defined in test specification

Displayed Results: Receiver PER. Requires EUT to support HCI or 2-Wire interface for automated PER resultsNumber of Measurement Frequencies: Three, default to RF Test Specification or user definedOutput Power Range: –90 to 0 dBm, resolution: 0 .1 dBOutput Power Accuracy: ±1 dB (–80 to 0 dBm)

Maximum input signal level [RF-PHY/RCV/BV-06-C (BLE), RF-PHY/RCV/BV-12-C (2LE)]

Measurement ConfigurationEUT configured to receive test reference packetsPacket payload: PRBS9

Displayed Results: Receiver PER. Requires EUT to support HCI or 2-Wire interface for automated PER resultsNumber of Measurement Frequencies: Three, default to RF Test Specification or user definedOutput Power Range: –90 to 0 dBm, resolution: 0 .1 dBOutput Power Accuracy: ±1 dB (–80 to 0 dBm)

PER report integrity [RF-PHY/RCV/BV-07-C (BLE), RF-PHY/RCV/BV-13-C (2LE), RF-PHY/RCV/BV-30-C (BLR S = 2), RF-PHY/RCV/BV-31-C (BLR S = 8)]

Measurement ConfigurationEUT configured to receive test reference packetsPacket payload: PRBS9CRC corruption: Alternate packetsNumber of test packets: Random [100 ≤ RND ≤ 1500]

Displayed Results: Receiver PER. Requires EUT to support HCI or 2-Wire interface for automated PER resultsNumber of Measurement Frequencies: One, default to RF Test Specification or user definedOutput Power Range: –90 to 0 dBm, resolution: 0 .1 dBOutput Power Accuracy: ±1 dBm (–80 to 0 dBm)

BLE Tx Power Stability [RF-PHY/TRM/PS/BV-01-C, RF-PHY/TRM/PS/BV-02-C, RF-PHY/TRM/PS/BV-03-C, RF-PHY/TRM/PS/BV-04-C]

Measurement ConfigurationEUT configured to transmit Test Reference PacketsNo payloadAoD Constant Tone Extensions

Displayed resultsMaximum deviation to average power during reference periodMaximum deviation to average power for each transmit slot

Number of measurement frequencies: Three, default to RF Test Specification or user definedMeasurement Range: –50 to +22 dBm (average power), +23 dBm (peak power)Resolution: 0 .01 dB

7

MT8852B Signal Generator

FrequencyFrequency Range: 2 .4 GHz to 2.5 GHzFrequency Resolution: 1 kHzFrequency Accuracy: As frequency standard ±500 Hz

LevelAmplitude Range: –90 to 0 dBmAmplitude Accuracy: ±1 dB (–80 to 0 dBm)Amplitude Resolution: ±0.1 dBOutput Impedance: 50Ω (nominal)Output VSWR: 1.5:1, 1 .3 :1 (typical), Adjacent channels 3 or higher –40 dBc

GFSK ModulationModulation Index: Variable, 0 .25 to 0.50 (125 kHz to 250 kHz)Modulation Index Resolution: 0 .01Modulation Index Accuracy: 1% (nominal) for modulation index = 0.32Baseband Filter: BT = 0.5

*: Supports low energy signal generator compliant with Bluetooth Core Specification v5.1

π/4DQPSK ModulationModulation Index Accuracy: <5% RMS DEVMBaseband Filter: BT = 0.4

8DPSK ModulationModulation Index Accuracy: <5% RMS DEVMBaseband Filter: BT = 0.4

MT8852B Measuring Receiver

FrequencyFrequency Range: 2 .4 GHz to 2.5 GHzFrequency Resolution: 1 kHzFrequency Accuracy: As frequency standard ±500 Hz

LevelRange: –55 to +22 dBm (average power)Power Measurement Accuracy: ±1 dB (–35 to +20 dBm)Input VSWR: 1.5:1Damage Level: +25 dBmResolution: 0 .1 dB

GFSK ModulationDeviation Measurement Range: 0 to 350 kHz (peak power)Accuracy: 1% for modulation index 0.32

EUT Control InterfaceRS232 HCI Commands

The EUT control interface provides RS232 HCI commands to the EUT through a standard RS232 interface. The interface meets the requirements of the Bluetooth specification for HCI UART transport layer. An RS232 cable is supplied.

USB HCI CommandsThe EUT control interface provides USB HCI commands to the EUT through a standard USB interface. The interface meets the requirements of the Bluetooth specification section H:2. A USB cable is supplied.

2-Wire Control: For test control of Bluetooth low energy devices the EUT control interface supports the 2-Wire specificationUSB to RS232 HCI Command: For use with EUTs fitted with USB to RS232 FTDI chipsUSB to 2-Wire Command: For use with EUTs fitted with USB to RS232 FTDI chips that support 2-Wire control

8

Audio SpecificationsNumber of SCO Channels Supported: 3Codec Air Interfaces Supported: CVSD, A-Law, µ-LawFrequency Response

(–3 dB) measured CODEC in to CODEC out: 160 Hz to 3.5 kHz. Measured with 50Ω source impedance and 10MΩ load impedance

Maximum Input/Output Signal Level: 3 .4 Vpk-pk = 1.2 V RMSDistortion/Noise

A law: –37 dB (typical) (1 kHz, 1 V RMS) µ law: –37 dB (typical) (1 kHz, 1 V RMS) CVSD: –30 dB (typical) (300 Hz, 1 V RMS)

Input/Output Connectors: 3 .5 mm audio jack plugs (one for each SCO channel)Input Impedance: 20kΩMinimum Output Load: 600ΩInternal Audio Source: 1 kHz fixed frequency

Adaptive Frequency Hopping (MT8852B-015)Supported in ACL and SCO connections

Displays: Active channel vs. time, FER vs. timeOther Features: ACL connection timer, resolution: 1 ms

Electrical Characteristics

Frequency StandardFrequency: 10 MHzTemperature Stability: ±0.5 ppm (–10° to +85°C)Aging (1st year): ±1.0 ppmAging (over 10 years): ±2.5 ppm (including year 1)

Rear Panel ConnectorsExternal Frequency Standard Input: Rear panel, BNC connector, 50Ω, 1 VOutput 1: TTL output for TX ON, TX DATA, RX DATA, and correlatorOutput 2: TTL output for RX ON, TX DATA, RX DATA, and correlatorInput 1: For service use only

GPIBIEEE 488.2: Offers full instrument control as standard

RS232RS232: Offers full instrument control as standard

General

Power SupplyRated Voltage: 100 Vac to 120 Vac/200 Vac to 240 VacRated Frequency: 50 Hz/60 HzPower Consumption: 150 VA max.

EnvironmentalOperating Temperature: +5° to +40°COperating Humidity: 20 to 75%

EU Standards (CE Marking)EMC: EN61326-1, EN61000-3-2LVD: EN61010-1RoHS: EN50581

Dimensions and MassDimensions: 216.5 (W) × 88 (H) × 380 (D) mmMass: <3.8 kg

9

Model/Order No Name

MT8852BMT8852B-040MT8852B-041MT8852B-042MT8852B-043

Main FrameBluetooth Test SetBluetooth Test SetBluetooth Test SetBluetooth Test SetBluetooth Test Set

J1783AJ1784AJ1785A

J1786A

Standard AccessoriesMT8852B Bluetooth Test Set Operation Manual MT8852B Bluetooth Test Set Operation Manual Remote ControlUSB HCI control interface leadRS232 HCI Control Interface LeadRS232 Cable for Firmware UpdatesPower CordBlueSuite Software Bluetooth Low Energy Measurement Software applicationMT8852B Bootloader3.5 mm Jack Plugs (Qty. 3)

MT8852B-015MT8852B-017MT8852B-027MT8852B-034*1

MT8852B-035*1, *2

MT8852B-036*1, *2, *3

MT8852B-037*1, *2, *3

MT8852B-070

Options and AccessoriesAdaptive Frequency Hopping optionIQ data outputBluetooth low energy measurementsBLE Data Length Extension OptionBLE 2LE Option BLE BLR OptionBLE AoA/AoD Option (Angle of Arrival/Angle of Departure)Platform Enhancement Option

Model/Order No Name

MT8852B-315*4

MT8852B-317*4

MT8852B-319*4

MT8852B-325*4

MT8852B-327MT8852B-330MT8852B-334*1

MT8852B-335*1, *2

MT8852B-336*1, *2, *3

MT8852B-337*1, *2, *3

MT8852B-170MT8852B-270MT8852B-370

Retrofit Adaptive Frequency Hopping optionRetrofit IQ data outputRetrofit Audio to MT8852BRetrofit EDR to MT8852BRetrofit Bluetooth low energy measurementsRetrofit Basic Rate Measurement to MT8852BRetrofit BLE Data Length Extension OptionRetrofit BLE 2LE OptionBLE BLR Option RetrofitBLE AoA/AoD Option RetrofitPlatform Enhancement Option Retrofit Platform Enhancement Option RetrofitPlatform Enhancement Option Retrofit

MX885201BMX885201B-301Z1992AB0748AB0749AJ0006J0007J0008J0127AJ0127BJ0127C

BlueSuite Pro3 software applicationBlueSuite Pro2 to Pro3 Upgrade2.4 GHz Antenna and AdapterSoft Carry BagRack Mount KitGP-IB CABLE, 0.5MGPIB CABLE, 1.0MGPIB CABLE, 2.0MCOAXIAL CORD, 1.0MCOAXIAL CORD, 2.0MCOAXIAL CORD, 0.5M

*1: MT8852B-034 (334) requires MT8852B-027 (327) or MT8852B-043.

*2: MT8852B-035 (335), MT8852B-036 (336) and MT8852B-037 (337) requires MT8852B-034 (334).

*3: MT8852B-036 (336) and MT8852B-037 (337) requires MT8852B-070 (270, 370).

*4: When installing MT8852B-315/317/319/325 to MT8852B-043, MT8852B-330 is necessary.

Please specify the model/order number, name and quantity when ordering.The names listed in the chart below are Order Names. The actual name of the item may differ from the Order Name.

Ordering Information

10

Note

11

Note

Anritsu Americas Sales Company

Phone: +1-800-Anritsu (1-800-267-4878)

• CanadaAnritsu Electronics Ltd.700 Silver Seven Road, Suite 120, Kanata, Ontario K2V 1C3, CanadaPhone: +1-613-591-2003 Fax: +1-613-591-1006

• Brazil Anritsu Eletronica Ltda.

Phone: +55-11-3283-2511Fax: +55-11-3288-6940

• MexicoAnritsu Company, S.A. de C.V.Blvd Miguel de Cervantes Saavedra #169 Piso 1, Col. Granada Mexico, Ciudad de Mexico, 11520, MEXICOPhone: +52-55-4169-7104

• United KingdomAnritsu EMEA Ltd. 200 Capability Green, Luton, Bedfordshire, LU1 3LU, U.K.Phone: +44-1582-433200 Fax: +44-1582-731303

• FranceAnritsu S.A. 12 avenue du Québec, Bâtiment Iris 1- Silic 612,91140 VILLEBON SUR YVETTE, FrancePhone: +33-1-60-92-15-50Fax: +33-1-64-46-10-65

• GermanyAnritsu GmbHNemetschek Haus, Konrad-Zuse-Platz 1 81829 München, Germany Phone: +49-89-442308-0Fax: +49-89-442308-55

• ItalyAnritsu S.r.l.Via Elio Vittorini 129, 00144 Roma, ItalyPhone: +39-6-509-9711 Fax: +39-6-502-2425

• SwedenAnritsu ABIsafjordsgatan 32C, 164 40 KISTA, SwedenPhone: +46-8-534-707-00

• FinlandAnritsu ABTeknobulevardi 3-5, FI-01530 VANTAA, FinlandPhone: +358-20-741-8100Fax: +358-20-741-8111

• DenmarkAnritsu A/STorveporten 2, 2500 Valby, DenmarkPhone: +45-7211-2200Fax: +45-7211-2210

• RussiaAnritsu EMEA Ltd. Representation Office in RussiaTverskaya str. 16/2, bld. 1, 7th floor.Moscow, 125009, RussiaPhone: +7-495-363-1694Fax: +7-495-935-8962

• SpainAnritsu EMEA Ltd.Representation Office in SpainEdificio Cuzco IV, Po. de la Castellana, 141, Pta. 528046, Madrid, SpainPhone: +34-915-726-761Fax: +34-915-726-621

• United Arab EmiratesAnritsu EMEA Ltd. Dubai Liaison Office

• P.R. China (Shanghai)Anritsu (China) Co., Ltd.Room 2701-2705, Tower A, New Caohejing International Business CenterNo. 391 Gui Ping Road Shanghai, 200233, P.R. ChinaPhone: +86-21-6237-0898Fax: +86-21-6237-0899

• P.R. China (Hong Kong)Anritsu Company Ltd.Unit 1006-7, 10/F., Greenfield Tower, Concordia Plaza,No. 1 Science Museum Road, Tsim Sha Tsui East, Kowloon, Hong Kong, P.R. ChinaPhone: +852-2301-4980Fax: +852-2301-3545

• JapanAnritsu Corporation

Phone: +81-46-296-6509Fax: +81-46-225-8352

8-5, Tamura-cho, Atsugi-shi, Kanagawa, 243-0016 Japan

• KoreaAnritsu Corporation, Ltd.5FL, 235 Pangyoyeok-ro, Bundang-gu, Seongnam-si, Gyeonggi-do, 13494 KoreaPhone: +82-31-696-7750Fax: +82-31-696-7751

• AustraliaAnritsu Pty. Ltd.

Phone: +61-3-9558-8177Fax: +61-3-9558-8255

• TaiwanAnritsu Company Inc.7F, No. 316, Sec. 1, NeiHu Rd., Taipei 114, TaiwanPhone: +886-2-8751-1816Fax: +886-2-8751-1817

1811

Printed on Recycled Paper

• SingaporeAnritsu Pte. Ltd.11 Chang Charn Road, #04-01, Shriro HouseSingapore 159640Phone: +65-6282-2400Fax: +65-6282-2533

• IndiaAnritsu India Private Limited6th Floor, Indiqube ETA, No.38/4, Adjacent to EMC2, Doddanekundi, Outer Ring Road, Bengaluru – 560048, IndiaPhone: +91-80-6728-1300Fax: +91-80-6728-1301

Specifications are subject to change without notice.

• United States

Unit 20, 21-35 Ricketts Road, Mount Waverley, Victoria 3149, Australia

902, Aurora Tower,P O Box: 500311- Dubai Internet CityDubai, United Arab EmiratesPhone: +971-4-3758479Fax: +971-4-4249036

Praça Amadeu Amaral, 27 - 1 Andar01327-010 - Bela Vista - Sao Paulo - SPBrazil

450 Century Parkway, Suite 190, Allen, TX 75013, U.S.A.

Printed in Japan 20/AUG/2019 ddcm/CDT Catalog No. MT8852B_DataSheet-E-A-1-(5.00)