Bluetooth For water Vending machineeca99.com/Manuals/ECA4058.pdf · For water Vending machine For...

Manual for Coin Dispensing Controller Model no. ECA4056/4056gsm/ECA4057 Rev-3.0

A product of Extreme Controls & Automation pvt.ltd

Coin vending controller

Bluetooth

For water Vending machine For Model No. ECA4058



Serial no is back side of product

Introduction

ECA 4058 is a coin vending controller. It is used in water vending machines.

We can use JY926 or ICT UCA2 coin acceptor with this controller and any other

coin acceptor can also be attached with the help of customer care support.

This is very high tech as well as price efficient model. This is economical

model for water vending machine. This is highly precise and long durable

product. We can operate it in several operating modes.

It mainly works in two modes. That is flow meter mode and timer mode. Flow

mode and timer mode. These are described below:-

A product of Extreme Controls & Automation pvt.ltd Setting Menu:-

This product is Bluetooth enabled device, it have inbuilt Bluetooth module that can be paired with mobile and laptop. To pair with mobile you need an app Bluetooth spp pro tool, Available on Google play store

ECA- 11641



A product of Extreme Control & Automation Pvt. Ltd

Enter pin is 1234 for pairing. When pairing complete the next ask for connect

Now click on connect

Then next ask for

Click on Byte Stream Mode button


Now when click on Byte stream mode terminal screen will open like:-



Send Button is here

Now do not wait for waiting to receive .now type and send password to open setting menu

Login Password is required to operate any control panel from android mobile. You may know default password from your administrator .This is six characters password from which login can be done.

All further commands will work only when login is done properly. Any command given without login will revert as invalid command.

If you see invalid command its mean that either you didn’t login or not given command properly.

Command format is [pw][space][password like 123456]. e.g.

pw xxxxxx



There are two types of password first is user/operator password and second is master password.

All basic setting can be done by user password, whereas some special setting can be done by master password on demand of administrator only.

Flow Meter Mode In this mode dispense is done based on flow sensor counts. In this mode flow sensor is deployed in dispensing outlet pipe line. Flow meter is used for getting batter accuracy to avoid variation occurred due to increase or decrease tank level. When water flows from flow sensor, there is a wheel in the flow sensor that rotates. The controller senses each rotation when water flows. After completing the counts as programmed by user controller stop the dispensing.

For setting Controller in flow meter mode.

The command format is [mode2][space][f] for flow miter mode

[mode2][Space][t] For timer mode

The factory default is timer mode

e.g.

mode2 f for flow miter mode

mode2 t for timer mode

Coin Acceptor Setting We can use these six types of coins in that coin acceptor.



Which is called (A for 1 rupee coin) (B for 2 rupee coin) (C for 5 rupee coin) and (D for 10 rupee coin).

Dispense Quantity Setting In this we can program dispense quantity for each type of coins individually. If the controller is set in timer mode then the quantity setting is in multiple of 10milliseconds. For example= If we want to run the relay for 1 second so we program 100 counts for 1 sec.

And if we want to set relay runtime for 5 seconds then we program 500 counts.

The command format is [cnt][space][x][500]

Where

X is replaced by a for 1Rs.

X is replaced by b for 2Rs.

X is replaced by c for 5Rs.

X is replaced by d for 10Rs.

If Controller is operating in flow meter mode



Then

You give command [cnt][space][x][y]

Where:-

Y is the no. of counts required to complete dispense for that coin.

X is replaced by a for 1Rs.

X is replaced by b for 2Rs.

X is replaced by c for 5Rs.

X is replaced by d for 10Rs.

For example= If we want 100cnt for 1 rupee then we give [cnt][space][a][100] for 1 rupee

e.g.

cnt a100

If you want to know how much quantity for each coin is programmed in setting menu.

So you can read it all in single command. The command format is [cnt][space][?]

e.g.

cnt ?

Coin Acceptor manual

Manual of CH-926

CH-926 is a multi coin selector, can accept up to 6 kinds of different coins at the Same time. This type of coin selector is widely used in Vending machine, Arcade



Game, Message chair, and other self–management system. CH-926 is mainly based On material, weight and size to identify coins. We use the most up to date algorithm to Design software. Therefore, CH-926 is very stable and accurate even when Environment changes such as temperature, and humidity etc… In order to increase the Accuracy, we suggest different version of coins use different channel to set up.

Specifications

Coin diameter：：：： 15mm~32mm Atmospheric pressure：：：： 86Kpa—106Kpa Coin thickness：：：：1.2mm~3.8mm Working humidity：：：：≤95% Working voltage：：：： DC +12V ±10% Speed：：：：≤0.6s Working current：：：： 65mA ±5% Accuracy rate of identification：：：：99.5% Signal output: pulse

Features

A. Capable of accepting all worldwide Coins and Tokens. B. Intelligent CPU software control and high accuracy. C. Self-programming without PC. D. Accept 1~6 different kinds of coins at the same time. E. Free to set up pulses' output. F. Prevent not only electric shock but also electromagnetic interference. G. Automatic self-tests for problems.

Manual of CH-926

The Process of Setup for Parameters



1. Press the "Add" and "minus" buttons at the same time for about three seconds, then the Letter "A" will appear From the LED display. 2. Press the "setup" button once, and the letter "E" will appear. Next, use the buttons to Choose how many kinds of coins you would like to use; then press the "setup" button Again to finish. 3. The letter "H" will appear after pressing the button. Use the "Add" and "minus" buttons to Choose how many Samples you would like to insert later. Next press the "setup" button Again to finish. 4. The letter "P" will appear after pressing the button. Use the "Add" and "minus" buttons to Choose the amount of output's signals/pulses you want. The quantity limited is 50 times. Next, press the "setup" button to finish. 5. The letter "F" will appear after pressing the button. Use the "Add" and "minus" buttons to Choose accuracy. The value is from 1~ 30 and 1 is the most accurate. Normally, 5~10 will Be fine. Next, press the "setup" Button to finish. 6. So far, you have successfully set up the first coin. Please repeat all above procedures until You have set up all the coins. The letter "A" will appear again after all above procedures Are finished. 7. Press the "setup" button, and the letter "E" will appear. Finally, turn off and turn on the Power. The setup will be stored.

You can start sampling after the setup is finished. Please choose at least 20 coins. The

sampling process will affect the accuracy of coin selector.

Sampling

1. Press the "setup" button, then letter "A" will appear from the LED display. 2. Press the "setup" button again, and then letter "A1" will appear. Next, start to insert Sample Coins. The LED Display will show how many coins you insert. The letter "A1" will appear again after Finished. 3. Press the "setup" button again, then the letter "A2" will appear. Next, start to sample 2nd Coin and repeat no. 1 and No. 2 until all the coins are set up . 4. After finished the sampling, press the "setup" button. The letter "A “will appear, then turn

Off and turn on the

Power. Now you can start to use it.

Connections' manual



Manual of CH-926

FAQ:

A. Coins can't pass through

1. Check if the connection is correct or poor connection. 2. Check if sampling is appropriate. 3. Check if there is something stuck inside. B. Can't identify outputs

1. Check if 2 way switch -NO. NC. - are correct. 2. Check if Single wire is connected correctly. 3. Check if there is pull-up resistor with signal wire (not allowed). 4. Check if there is something stuck on the channel where the coins pass out. C. Coins cannot pass smoothly

1. Check if the parameter is set up appropriately. 2. Check the accuracy switch 3. Check if there is something stuck on the channel where the coins pass out.

Name and Function



① LED light - The light of Indication.

② 4pin Socket

③ two way switch – signal output NO. Or NC.

④ Three way switch - Output signal - fast: 20ms, medium: 50ms, slow: 100ms

⑤ 2pin Socket - Electromagnetic valve DC 12V

⑥ “Setup” button

⑦ LED display

⑧ “Add” button - Plus "+" value

⑨ “Minus “button - Minus “-” value

⑩ Coin slot

11 Press-button for removal of blocked coin

12 Return slot of Coin

13 Position of electromagnetic strobe

Warning: - Remember gray wires should never touch

each other while panel on otherwise panel will bloom.

And relay driver will be destroyed.

Bluetooth For water Vending machineeca99.com/Manuals/ECA4058.pdf · For water Vending machine For...

Documents

Transcript of Bluetooth For water Vending machineeca99.com/Manuals/ECA4058.pdf · For water Vending machine For...