Bldg Construction Chapter 02
-
Upload
shyla-chaplin -
Category
Documents
-
view
596 -
download
1
Transcript of Bldg Construction Chapter 02
![Page 1: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/1.jpg)
Building Construction Related to the Fire
Service
Chapter 2 — Structural Fire Resistance and Building
Classifications
![Page 2: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/2.jpg)
Learning Objective 1
Define fire resistance.
Building Construction2–2
![Page 3: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/3.jpg)
Fire Resistance
• Function of the properties of all materials used; includes combustibility, thermal conductivity, chemical composition, density, and dimensions
• Ability of a structural assembly to maintain load-bearing and structural integrity under fire conditions
Building Construction
(Continued)
2–3
![Page 4: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/4.jpg)
Fire Resistance
• Ability of walls, partitions, and ceilings to act as a fire barrier
• Fire resistance rating– Expressed in hours and fractions of
hours– Incorporated into construction
classifications and building codes
Building Construction2–4
![Page 5: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/5.jpg)
Learning Objective 2
Discuss methods of determining fire resistance and the limitations of each method.
Building Construction2–5
![Page 6: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/6.jpg)
Determination of Fire Resistance
• Conducting standard fire resistance testing in a laboratory
• Performing analytical calculations to determine the resistance to a standard fire test exposure
• Employing analytical structural fire engineering design methods based on real fire exposure characteristics
Building Construction2–6
![Page 7: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/7.jpg)
Fire Resistance Test Method
• Laboratory test is most commonly used method
• Component subject to heat of a standard fire in test furnace
• Primary points of failure for test• Fire resistance ratings expressed in
standard intervals
Building Construction2–7
(Continued)
![Page 8: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/8.jpg)
Fire Resistance Test Method
• Factors impacting fire resistance ratings from standard test
• Standard fire test evaluates ability of structural assemblies to carry a structural load and act as a fire barrier
• Information NOT provided by test• Assemblies may be penetrated
Building Construction2–8
(Continued)
![Page 9: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/9.jpg)
Fire Resistance Test Method
Building Construction2–9
![Page 10: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/10.jpg)
Learning Objective 3
Identify fire testing organizations and discuss the significance of fire test results.
Building Construction2–10
![Page 11: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/11.jpg)
Fire Testing Organizations
• Testing for fire resistance ratings is beyond capability of local fire and building departments
• Several laboratories are equipped to conduct testing
• Some organizations use furnaces primarily for research and product development
Building Construction2–11
![Page 12: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/12.jpg)
Fire Test Results
• Published by testing laboratories
• Deviation from materials or dimensions specified alters test results
Building Construction2–12
![Page 13: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/13.jpg)
Learning Objective 4
Recognize the role of analysis in determining fire resistance.
Building Construction2–13
![Page 14: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/14.jpg)
Analytical Calculation of Fire Resistance
• Mathematical equations have been developed to predict behavior of materials under test conditions
• ASCE/SFPE 29 provides methods for calculating fire resistance ratings
• Limited to use with certain materials
Building Construction2–14
![Page 15: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/15.jpg)
Analytical Design Using Real Fire Exposures
• NFPA® 251 test– Most commonly used– May be too severe or not severe
enough
• Ratings determined analytically using a different time-temperature curve must be interpreted cautiously
Building Construction2–15
![Page 16: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/16.jpg)
Noncombustible Materials
• Building codes contain explicit criteria for determining combustible material
• Incapable of supporting combustion under normal circumstances
• Most common test for determining combustibility – ASTM E 136
Building Construction2–16
![Page 17: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/17.jpg)
Learning Objective 5
Discuss the basic building classifications as they relate to fire resistance.
Building Construction2–17
![Page 18: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/18.jpg)
Classifications
• Type I, Fire-Resistive• Type II, Noncombustible or
protected noncombustible• Type III, Exterior protected• Type IV, Heavy timber• Type V, Wood frame
Building Construction2–18
(Continued)
![Page 19: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/19.jpg)
Classifications
• In building codes, based on materials used in construction and hourly fire resistance ratings required for structural components
Building Construction2–19
![Page 20: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/20.jpg)
NFPA® 220
• Details requirements for each classification and subclassification
• Designated by three-digit number code– 1st – Fire resistance rating in hours of
exterior bearing walls– 2nd – Fire resistance rating of structural
frames or columns and girders supporting loads greater than one floor
– 3rd – Fire resistance rating of floor construction
Building Construction2–20
![Page 21: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/21.jpg)
International Building Code® (IBC®)
• Similar to NFPA® 220• Requirements for individual
structural members differ• Building codes use construction
types and occupancy in conjunction with sprinkler systems and separations to establish limits on heights and areas of buildings
Building Construction2–21
![Page 22: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/22.jpg)
Type I Construction
• Structural membersare noncombustible construction with a specified fire resistance
• Combustible material typically permitted in certain components
• Most common methods of construction
Building Construction2–22
Courtesy of McKinney (TX) Fire Department
![Page 23: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/23.jpg)
Type II Construction
• Noncombustible – Can be either protected or unprotected
• IBC® divides into two subclassifications
• Material other than steel can be used
• Building codes allow combustible material similar to that in Type I
Building Construction2–23
(Continued)
![Page 24: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/24.jpg)
Type II Construction
• Unprotected, noncombustible building cannot be expected to provide structural stability under fire conditions
• Point at which unprotected members will fail depends on several factors
• Protected, noncombustible structural fire protection is similar to Type I
Building Construction2–24
![Page 25: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/25.jpg)
Type III Construction
• “Ordinary construction”• Exterior walls frequently masonry,
but can be any noncombustible material with required fire resistance
• Interior members– Partially or wholly combustible– Protected or unprotected
Building Construction2–25
(Continued)
![Page 26: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/26.jpg)
Type III Construction
• IBC® divides into two subclassifications
• When fire resistance is required, most common is plaster (older) or gypsum board (newer)
• Wood dimensions permitted to be smaller than Type IV
• Fundamental fire concern – Concealed spaces
Building Construction2–26
![Page 27: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/27.jpg)
Type IV Construction
• “Mill construction”• Difference from Type III• Used in older factories,
mills, and warehouses• Primary fire hazard –
Massive amount of fuel from large structural members
Building Construction2–27
Courtesy of McKinney (TX) Fire Department
![Page 28: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/28.jpg)
Type V Construction
• All structural components may be combustible
• Two subclassifications• Differences from Type
III• Threat to adjacent
structures if heavily involved in fire
Building Construction2–28
![Page 29: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/29.jpg)
Mixed Construction
• Some buildings are allowed a mixed construction type
• May result in special challenges for emergency responders
Building Construction2–29
![Page 30: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/30.jpg)
Learning Objective 6
Discuss the concept of fire load and its impact on building construction types.
Building Construction2–30
![Page 31: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/31.jpg)
Fire Load
• Maximum heat released if all available fuel in a building was consumed
• Product of weight of combustibles multiplied by their heat of combustion
• Expressed in lb/sq ft (kg/sq m)• Varies depending on heat of
combustion of fuelBuilding Construction
2–31
![Page 32: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/32.jpg)
Fire Load and Construction Type
• Buildings with combustible structural components have greater fire load than Type I and II
• Fire load does not translate into equivalent structural load
Building Construction2–32
![Page 33: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/33.jpg)
Learning Objective 7
Explain occupancy classifications as they relate to fire risks.
Building Construction2–33
![Page 34: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/34.jpg)
Occupancy Classifications
• Assign building occupancies into groups with broadly similar fire risks
Building Construction2–34
![Page 35: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/35.jpg)
IBC® Classifications
• Group A – Assembly
• Group B – Business• Group E –
Education• Group F – Factories• Group H – High
Hazard
• Group I – Institutional
• Group M – Mercantile
• Group R – Residential
• Group S – Storage• Group U – Utility
and Misc.Building Construction
2–35
![Page 36: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/36.jpg)
International Building Code®
• Considerable variation of hazards within groups, so further divided to describe occupancy groups with more similar characteristics
• Total of 26 subgroups• Separate provision for one- and
two-family dwellings not more than three stories high
Building Construction2–36
![Page 37: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/37.jpg)
NFPA® Classifications
• Assembly• Educational• Day care• Health care• Ambulatory
health care• Detention and
correctional
• Residential• Residential board
and care• Mercantile• Business• Industrial• Storage
Building Construction2–37
![Page 38: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/38.jpg)
Mixed Occupancies
• Buildings may contain more than one occupancy classification
• Codes require fire-resistive separations between various occupancies
• Requirements depend on local code• Reduction in occupancy separation
may be permitted if building is sprinklered
Building Construction2–38
![Page 39: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/39.jpg)
Change of Occupancy
• Frequently occurs• Can create problems• May require expensive renovations
that owner not willing to pay
Building Construction2–39
![Page 40: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/40.jpg)
Summary
• Fire behavior in buildings is determined largely by construction materials and structural fire resistance.
• Structural fire resistance is determined most often through laboratory testing.
Building Construction2–40
(Continued)
![Page 41: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/41.jpg)
Summary
• Building codes classify construction into types based on construction material, structural fire resistance, and occupancy.
• Occupancies within individual occupancy groups present roughly similar fire risk factors.
Building Construction2–41
![Page 42: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/42.jpg)
Building Construction
Review Questions
1.What is fire resistance?2.What is the value of standard fire tests?3.What is a noncombustible material?4.What considerations do firefighters need to take into account when they encounter dropped ceilings?
(Continued)
2–42
![Page 43: Bldg Construction Chapter 02](https://reader034.fdocuments.in/reader034/viewer/2022042607/5562699cd8b42a14048b53b4/html5/thumbnails/43.jpg)
Review Questions
5.What are the major occupancy classifications contained in the International Building Code® (IBC®)?
Building Construction2–43