1. User manual V2.0

2. Thank you for purchasing BlackView.BlackView is aportable, Stylish, high-performance vehicle driverecorder. It has 5.0M effective pixel high-definition CMOSimage sensor, intelligent voice reminder, enhancednight shooting,140wide-angle lens.Specific performance parameters are as follows: CMOS sensor 5,000,000 pixels Viewing angle o f lensWide-angle 140 Turning angle of lens 200 back and fo rth Screen2.0TFT high resolution Quality vedio HD(1280720)@30 fps Night visionEnhanced night vision Format of picture JPEG Pixel of picture2560x1920 Voice guidanceintelligent voice guidance Type of memory card TF card Capacity of memory Card Supports up to 32G Battery 800MA Polymer lithium battery Power consumption 150MA 3. Checking the packing contentCheck the product and the accompanied accessories!If there is any problem of the accessories, contact your local productdistributor.BlackViewSupport SlotUser m n aual Cable holdersPower cableDriver disk 4. Checking the main body of the BlackView Enhanced night vision lightSpeaker TFT LCD LensSupport slot ResetVedio Play Camera TF Card SlotMicrophone USB InterfaceSwitching&Menu 5. Installing the BlackView1.Stop the engine and remove the key from the ignition. Install the BlackView in a well-lit and safe location.2.Insert the Micro SD card into the BlackView.3.Attach the BlackView into the windshield of your car using double-sided tape. Use a soft and dry cloth to wipe the foreign material and moisture attached in the surface of the support slot.4.Connect the [USB] terminal of the BlackView and the cigarette jack of your car using the power cable.5.Tie the power cable Use the provided cable holder, when necessary.6.Adjust the position of the camera lens of the BlackView. Ensure that it is level with the ground.7.Start the engine. Check whether the BlackView is installed When the BlackVue is installed correctly, its Intelligent voice systems will playThe BlackView has been starting normal recording. 6. Using the BlackViewUsing the Normal Recording Function Start the engine. BlackView turns on and starts the Normal Recording function. After it is turned on, it will records and saves scenes at each specified period. Stop the engine. BlackView will turn off after about 5 seconds.Using the Manual Reconrding Function Press the button on the BlackView. After BlackView turns on.Press the button to starts the Manual Recording function. It will record and saves scenes at each specified period. Press the button again.BlackView will exit Manual Recording function.Using the Camera Function When BlackView turns on. To enter the Camera Function Press the button. Press the button again.BlackView will take photograph.Using the Playback Function When BlackView turns on. Press and hold button for 2 seconds to enter the Playback Function. Press or button to select the video or photo which you want,Then Press button to play. Press and hold button for 2 seconds again. The BlackView will exit the Playback Function. 7. Setting the BlackViewSetting video outputVideo output includingSizeEVWhite Balance deo Time ght Mode Vi Ni1.Setting Size When System is turned on.Press button to display video output page. Press or button to selectSize,Then Press button to display Sub-page. Sub-page includingVGAQVGAD1HD,Press or button to select the setting which you want,Then Press button to confirm.Video output Setup SizeHD VGA EV+0.0 Q VGA White Balance Auto D1 Ve dio Time 1 Min Night ModeO ff Exit O K Set2.Setting EV When System is turned on.Press < Switching > button to display video output page. Press or button to selectEV,Then Press button to display Sub-page. Sub-page including+2.0+5/3+4/3+1.0+2/3+1/3 +0.0-1/3-2/3-1.0-4/3-5/3-2.0,Press or button to select the setting which you want,Then Press button to confirm. 8. Setting the BlackViewVideo outputSetup SizeHD +1/3 EV+0.0 +0.0 White Balance Auto -1/3 Ve dio Time 1 Min-2/3-1.0 Night ModeO ff Exit O K Set3.Setting White Blance When System is turned on.Press < Switching > button to display video output page. Press or button to selectWhite Blance,Then Press button to display Sub-page. Sub-page includingAutoDaylightCloudyTungsten Fluorescent,Press or button to select the setting which you want,Then Press button to confirm.Video outputSetup SizeHD Auto EV+0.0 Daylight White Balance Auto Cloudy Ve dio Time 1 MinTungstenFluoresce nt Night ModeO ff Exit O K Set 9. Setting the BlackView4.Setting Vedio Time When System is turned on.Press < Switching > button to display video output page. Press or button to selectNight Mode,Then Press button to display Sub-page. Sub-page includingOffOn,Press or button to select the setting which you want,Then Press button to confirm. Video outputSetupSizeHD O ffEV+0.0 1 MinWhite Balance Auto 2 MinVide o Time 1 MinNight ModeO ffExit O K Set5.Setting Night Mode When System is turned on.Press < Switching > button to display video output page. Press or button to selectNight Mode,Then Press button to display Sub-page. Sub-page includingOffOn,Press or button to select the setting which you want,Then Press button to confirm. 10. Setting the BlackView Video output SetupSizeHDEV+0.0O ffOnWhite Balance AutoVe dio Time 1 MinNight ModeO ffExit O K SetSetting SetupSetup includingFormatbeeplanguageauto offsys.resetLight Freq.USBScreen Set1.Setting Format When System is turned on.Double click button to display Setup page. Press or button to selectFormat,Then Press button to display subpage. Subpage includingCancelExecute,Press or button to select the setting which you want,Then Press button to confirm. Video outputSetupFormatNe xt Me nuBee p OnCancelLanguageEnglish Exe cuteAuto OffO ffSys.Re se t Ne xt Me nuExit O K Set 11. Setting the BlackView2.Setting Beep When System is turned on.Double click button to display Setup page. Press or button to selectBeep,Then Press button to display subpage. Subpage includingOnOff,Press or button to select the setting which you want,Then Press button to confirm. Video output SetupFormatNe xt Me nuBee p OnOnLanguageEnglish O ffAuto OffO ffSys.Re se t Ne xt Me nuExit O K Set3.Setting Language When System is turned on.Double click button to display Setup page. Press or button to selectLanguage,Then Press button to display subpage. Subpage includingEnglish ,Press or button to select setting which you want,Then Press button to confirm. 12. Setting the BlackViewVideo output Setup FormatNe xt Me nu Bee p On English LanguageEnglish Auto OffO ff Sys.Re se t Ne xt Me nu Exit O K Set4.Setting Auto Off When System is turned on.Double click button to display Setup page. Press or button to selectAuto Off,Then Press button to display subpage. Subpage including1 Min3 Min5 MinOff,Press or button to select the setting which you want,Then Press button to confirm.Video output Setup FormatNe xt Me nu Bee p On 1 Min LanguageEnglish3 Min Auto OffO ff 5 MinOff Sys.Re se t Ne xt Me nu Exit O K Set 13. Setting the BlackView5.Setting Sys.Reset When System is turned on.Double click button to display Setup page. Press or button to selectSys.Reset,Then Press button to display subpage. Subpage includingCancelExecute,Press or button to select the setting which you want,Then Press button to confirm.Video output Setup FormatNe xt Me nu Cancel Bee p LanguageExe cute LanguageDate Input Auto offLight Fre q. Sys.Re se t Ne xt Me nu Exit O K Set6.Setting Light Fre. When System is turned on.Double click button to display Setup page. Press or button to selectLight Fre.,Then Press button to display subpage. Subpage including60Hz50Hz,Press or button to select the setting which you want,Then Press button to confirm. 14. Setting the BlackView Video outputSetupLight Fre q.60Hz60Hz USBPC Cam50Hz Scree n SetAways OnExit O K Set7.Setting USB When System is turned on.Double click button to display Setup page. Press or button to selectLight Fre.,Then Press button to display subpage. Subpage including60Hz50Hz,Press or button to select the setting which you want,Then Press button to confirm. Video outputSetup Light Fre q. 60HzPC CamUSB PC CamDisk Drive Scree n SetAways OnExit O K Set 15. Setting the BlackView8.Setting Screen Set When System is turned on.Double click button to display Setup page. Press or button to selectScreen Set,Then Press button to display subpage. Subpage includingAlways On1 Min3 Min,Press or button to select the setting which you want,Then Press button to confirm.Video outputSetup Light Fre q.60Hz Away On USB PC Cam 1 Min Scree n Set Aways On Exit O K Set 16. Ballasoft