BIT3112 StaadPro AnalysisDesign Slab RC Structure

download BIT3112 StaadPro AnalysisDesign Slab RC Structure

of 16

Transcript of BIT3112 StaadPro AnalysisDesign Slab RC Structure

  • 8/13/2019 BIT3112 StaadPro AnalysisDesign Slab RC Structure

    1/16

    Analysis and Design of Reinforced Concrete Structure

    Creating member

    Start the Staad Pro. Choose Space, set the unit to kN and meter. ClickNext.Choose Open

    Structure Wizardand click Finish.

    Tick to Prototype model, choose Frame ModelsasModel Type, double click onBay Frameand

    fill in the blank as shown below. Length 6m (19.685 ft), Height 3m(9.843 ft), and Width

    6m(19.685 ft). Some of the features in StaadPro are not following the units setup by user. Then

    user needs to convert the values. For example, meter to foot. Then click Apply.

  • 8/13/2019 BIT3112 StaadPro AnalysisDesign Slab RC Structure

    2/16

    Next, click File,Merge Model with StaadPro model, click Yes (transfer/merge the model.) ,

    click OK to the Paste Prototype Model window (X,Y,Z = 0, 0, 0).

    Now the structure is displayed on the screen.

  • 8/13/2019 BIT3112 StaadPro AnalysisDesign Slab RC Structure

    3/16

    Click Geometry menu (top), select Run Structure Wizard, click Prototype Models, choose

    Surface/Plate Models and double click on Quad Plate.

    Fill in the blank as shown below. For Corners, X-B = 6m, X-C=6m, Z-C=6m and Z-D= 6m.

    Since the unit is in ft, then user has to convert the unit to ft. For Bias and Division, just put the

    number without convert, as shown below. Click Apply.

  • 8/13/2019 BIT3112 StaadPro AnalysisDesign Slab RC Structure

    4/16

    Next, click File,Merge Model with StaadPro model, and click Yes (transfer/merge the

    model.) , next for the Paste Prototype Modelwindow, set Yto 1.5 meter. Click OK.

    Properties

    Click General, Property(left side). ClickDefine (right side-properties window), choose Circle

    and insert 0.35 meter for YD. Click Add and Close.

    Highlight the circle properties, select all columns and clickAssign.Click Yes.

  • 8/13/2019 BIT3112 StaadPro AnalysisDesign Slab RC Structure

    5/16

    Again, clickDefineand selectRectangle.Insert 0.4 meter for YD and 0.25 meter for ZD. Add

    and Close.

  • 8/13/2019 BIT3112 StaadPro AnalysisDesign Slab RC Structure

    6/16

    Highlight the rectangle properties, and assign to all beam members. Other method, you can

    highlight the properties, then click Select (top-menu), selectBeams parallel to X, then repeat

    again to selectBeam Parallel to Z. Click Assign and Yes.

    Next, click to Thickness and insert 0.175 meters for all the nodes. Click Add and Close.

    Next, to assign the thickness properties, highlight the thickness properties, use Plate Cursor,

    select all slab andAssign, Yes.

    Now all the properties (circle,rectangle and thickness) have been assigned to all the members as

    shown below.

  • 8/13/2019 BIT3112 StaadPro AnalysisDesign Slab RC Structure

    7/16

    Supports

    CreateFixed support, and assign to all bases as shown in the figure.

    To see the 3D diagram of structure, right-click mouse, select Structure Diagrams, and tick the

    blank as shown.

  • 8/13/2019 BIT3112 StaadPro AnalysisDesign Slab RC Structure

    8/16

  • 8/13/2019 BIT3112 StaadPro AnalysisDesign Slab RC Structure

    9/16

    Loading

    Create aDead Load, click Selfweight, click Y and -1 as factor. Click Add and Close.

    Add new load underDead Loadcase. Click Floor Load, and fill in the blanks as follow. Click

    Add. StaadPro will automatically assign the floor loads to the beams.

  • 8/13/2019 BIT3112 StaadPro AnalysisDesign Slab RC Structure

    10/16

    You can adjust the load scales by clicking the right-mouse, Labels, Scales.

    Next, add another new load underDead Loadcase. Click to Plate Loads, choose Pressure on

    Full Plate and insert 10 kN/m2 for W1. Click Add and Close.

    Select all plates using Plate Cursoricon, and assign the pressure loads.

  • 8/13/2019 BIT3112 StaadPro AnalysisDesign Slab RC Structure

    11/16

    Next, we want to create new load case. ClickLoad Cases Details,Add, Primary, and name the

    title asLive 1. Click Add and Close.

    SelectLive 1,Add and select Floor Load, Floor. Fill in the blank as shown. Add and Close.

  • 8/13/2019 BIT3112 StaadPro AnalysisDesign Slab RC Structure

    12/16

    UnderLoad Cases Details,create the third load cases and name asLive 2.Add and Close. Then,

    selectLive 2, Addand select Floor Load, Floor.Fill in the blank as shown. Add and Close.

    UnderLoad Cases Details, create the fourth load cases and name asAdditional Live.Add and

    Close. Then, selectAdditional Live,Addand selectNodal Load, Node. Fill -150 kN on FY. Add

    and Close.

  • 8/13/2019 BIT3112 StaadPro AnalysisDesign Slab RC Structure

    13/16

    To assign the nodal load, click to theNode Cursoricon, click on the first floor level of the

    column at the left of the structure. ClickAssign to Selected Entities,Assignand Yes.

    Next, we want to create new load combination. ClickLoad Cases Details,Add , Define

    Combinations,and name as ULS. SelectLive 1, Live 2andAdditional Liveby click to the load

    name and click > . Insert 1.6 as load factor. Add and Close.

  • 8/13/2019 BIT3112 StaadPro AnalysisDesign Slab RC Structure

    14/16

    Analysis

    Run the analysis like previous exercise.Analysis/Print, Perform Analysis (No Print), Addand

    Close. ClickAnalyzeandRun Analysis. You can see the result of displacement and moment

    bending Z of the structure.

  • 8/13/2019 BIT3112 StaadPro AnalysisDesign Slab RC Structure

    15/16

    Slab Design

    Click to Post-Processingicon, Click toAdvanced Slab Design. Click to Slab Design(left side),

    Results(top menu), select Slab Reinforcementand a dialogue box will appear.

    Then, go toLoadingselect 5 ULS, then select Generaland fill in the blanks as shown.

  • 8/13/2019 BIT3112 StaadPro AnalysisDesign Slab RC Structure

    16/16

    Click OK. Then you will see the plate contour is displayed.