BILL OF QUANTITIES - CIVIL WORKS RENOVATION OF · PDF filePart 'A' Composite work of modular...

BILL OF QUANTITIES - CIVIL WORKS

RENOVATION OF 6TH FLOOR, ISBT, KASHMERE GATE, DELHI

Part 'A' Composite work of modular partitions, modular furniture, UPVC windows & Civil, Electrical & Fire Fighting

works

Rate in Rs. Amount

in Rs.

in figures in words

SH-1.00 DISMANTLING WORK

1.1 Demolishing brick work manually/ by

mechanical means including stacking of

serviceable material and disposal of

unserviceable material within 50 metres

lead as per direction of Engineer-in-

charge.

15.7.4 In cement mortar Cum 135

1.2 15.2.1 Demolishing cement concrete manually/ by

mechanical means including disposal of

material within 50 metres lead as per

direction of Engineer - in - charge.(a)

1:3:6 or richer mix.

Cum 42

1.3 15.12.1 Dismantling doors, windows and clerestory

windows (steel or wood)shutter including

chowkhats, architrave, holdfasts etc.

complete andstacking within 50 metres lead

Each 18

Item No DSR Ref Description Unit Qty

of 26

Rate in Rs. Amount

in Rs.

in figures in words


SH-2.00 FLOORING WORK

2.1 11.36 Providing and fixing Ist quality ceramic

glazed walls tiles conforming to IS:15622

(thickness to be specified by the

manufacture) of approved make in all

colours, shades except burgundy, bottle

green, black of any size as approved by

Engineer-in-charge in skirting, risers of

steps and dados over 12 mm thick bed of

cement Mortar 1:3 (1 cement : 3 coarse

sand) and jointing with grey cement slurry

@ 3.3kg per sqm including pointing in

white cement mixed with pigment of

matching shade complete.

Sqm 108

2.2 11.38 Providing and laying Ceramic glazed floor

tiles 300x300 mm(thickness to be specified

by the manufacturer) of Ist quality

conforming to IS:15622 of approved make in

all colours, shades, except White, Ivory,

Grey, Fume Red Brown, laid on 20mm thick

cement mortar 1:4 (1 Cement:4 Coarse sand)

including grouting the joints with white

cement and matching pigments etc.complete

Sqm 40

2.3 11.41.2 Providing and laying polished vitrified

floor tiles in different sizes (thickness

to be specified by the manufacturer) with

water absorption's less than 0.08% and

conforming to IS:15622 of approved make in

all colours and shades, laid on 20mm thick

cement mortar 1:4 ( 1 cement 4 coarse

sand) including grouting the joints with

white cement and matching pigments etc.

complete

Sqm 415

Size of Tile 60x60cm

2.4 4.1.3 Providing and laying in position cement

concrete of specified grade excluding the

cost of centering and shuttering - All

work up to Floor five Level

cum 9

of 26

Rate in Rs. Amount

in Rs.

in figures in words


1:2:4 (1 cement : 2 coarse sand : 4 graded

stone aggregate 20 mm nominal size)

2.5 8.2 Providing and fixing 18mm thick gang saw

cut mirror polished premoulded and

prepolished) machine cut for kitchen

platforms, vanity counters, window sills ,

facias and similar locations of required

size of approved shade, colour and texture

laid over 20mm thick base cement mortar

1:4 (1 cement : 4 coarse sand) with joints

treated with white cement, mixed with

matching pigment, epoxy touch ups,

including rubbing, curing, moulding and

polishing to edge to give high gloss

finish etc. complete at all levels.

8.2.2 Granite of any colour and shade

8.2.2.1 Area of slab upto 0.50 sqm Sqm 25

SH-3.00 BRICK WORK

3.1 6.4.2 Brick work with F.P.S bricks of class

designation 75 in superstructure above

plinth level up to floor V level in all

shapes and sizes in:

Cement mortar 1:6( 1 cement: 6 coarse

sand)

cum 75

3.2 6.13.2 Half brick masonry with F.P.Sbricks of

class designation 75 in super structure

above plinth level upto floor V level.

Cement mortar 1:4( 1 cement : 4 coarse

sand)

sqm 30

SH-4.00 RCC WORK

of 26

Rate in Rs. Amount

in Rs.

in figures in words


4.1 5.3 Reinforced cement concrete work in beams,

suspended floors,roofs having slope up to

15° landings, balconies, shelves,chajjas,

lintels, bands, plain window sills,

staircases and spiralstair cases up to

floor five level excluding the cost of

centering,shuttering, finishing and

reinforcement with 1:2:4 (1 cement :

2coarse sand : 4 graded stone aggregate 20

mm nominal size).

Cum 11

4.2 5.22.3 Reinforcement for R.C.C. work including

straightening, cutting,bending, placing in

position and binding all complete.Cold

twisted bars

kg 1000

4.3 Centering and shuttering including

strutting, propping etc. and removal of

form for

5.9.3 Suspended floors, roofs, landings,

balconies and access platform

sqm 50

5.9.5 Lintels, beams, plinth beams, girders,

bressumers and cantilevers.

sqm 40

5.9.16.1 Edges of slabs and bracks in floors and

walls (a) Under 20Cms wide.

Metres 28

SH-5.00 FINISHING WORK

5.1 13.4 12 mm cement plaster of mix :

13.4.1 1:4 (1 cement: 4 coarse sand) sqm 325

of 26

Rate in Rs. Amount

in Rs.

in figures in words


5.2 13.5 15 mm cement plaster on rough side of

single or half brick wall of mix :

13.5.1 1:4 (1 cement: 4 coarse sand) sqm 325

5.3 13.16 6 mm cement plaster of mix :

13.16.1 1:3 (1 cement: 3 fine sand) sqm 50

5.4 13.42 Distempering with 1st quality acrylic

washable distemper (ready mixed) of

approved manufacturer and of required

shade and colour complete as per

manufacturer's specification

13.42.1 Two or more coats on new work. sqm 610

5.5 13.68 French spirit polishing :

13.68.1 Two or more coats on new works including a

coat of wood filler

sqm 150

5.6 13.62 Painting with synthetic enamel paint of

approved brand and manufacture of required

colour to give an even shade:

13.62.1 Two or more coats on new work over an

under coat of suitable shade with ordinary

paint of approved brand and manufacture.

sqm 120

SH-6.00 WOOD WORK

of 26

Rate in Rs. Amount

in Rs.

in figures in words


6.1 9.1 Providing wood work in frames of doors,

windows, clerestory windows and other

frames, wrought framed and fixed in

position:

9.1.1. Second class teak wood Cum 3

6.2 9.3 Providing wood work in frames of false

ceiling, partitions etc. sawn and put up

in position:

9.3.2 Kiln seasoned and chemically treated

Hollock wood.

Cum 8

6.3 9.11 Extra for providing heavy sheet float

glass panes instead of ordinary float

glass in glazed doors, windows and

clerestory window shuttrs.(Area of oepning

for glass panes exluding portion inside

rebate shall be measured)9.11.1 5.5mm thick instead of 4mm thick Sqm 28

6.4 9.35 Providing and fixing in wall lining flat

pressed three layer (medium density)

particle board or graded wood Pre-

laminated one side decorative lamination

on other side balancing lamination Grade

1, Type II, IS:12823 marked including

priming coat on unexposed surface, with

necessary fixing arrangement and screws

etc. complete.

9.35.1 12mm thick Sqm 610

6.5 9.74 Providing and fixing bright finished brass

tower bolts (barrel type) with necessary

screws etc. complete

of 26

Rate in Rs. Amount

in Rs.

in figures in words


9.74.1 250x10 mm each 22

9.74.4 100x10 mm each 22

6.6 9.76 Providing and fixing bright finsihed brass

100mm mortice latch and lock with 6 levers

and a pair of lever handles with necessary

screws etc. complete (best make of

approved quality)

each 22

6.7 9.82 Providing and fixing bright finsihed brass

hanging type floor door stopper with

necessary screws, etc. complete

each 22

6.8 9.101 Providing and fixing aluminium hanging

floor door stopper ISI on marked anodised

(anodic coating not less than grade AC 10

as per IS:1868) transparant or dyed to

required colour and shade with necessary

screws etc. complete

9.101.2 Twin rubber stopper each 18

6.9 9.20 Providing and fixing ISI marked flush door

shutters conforming to IS:2202 (Part 1)

decorative type, core of block baord

construction with frame of Ist class hard

wood and well matched teak 3 ply veneering

with vertical grains or cross bands and

face veneers on both faces of shutters.

9.20.2 30mm thick including ISI marked Stainless

Steel butt hinges with necessary screws.

Sqm 42

of 26

Rate in Rs. Amount

in Rs.

in figures in words


6.10 12.45 Providing and fixing at all height false

ceiling including providing and fixing of

frame work made of special sections power

pressed from M.S. sheet and galvanised in

accordance with zinc coating of grade 350

as per IS: 277 and consisting of angle

cleats of size 25mm wide x 1.6mm thick

with flanges of 22mm and 37mm at 1200mm

centre to centre one flange fixed to the

ceiling with dash fastener 12.5mm diax40mm

long with 6mm dia bolts to the angle

hangers of 25x25x0.55mm of required

length, and other end of angle hanger

being fixed with nut and bolts to G.I

channels 45x15x0.9mm running at the rate

of 1200mm centre to centre to which the

ceiling section 0.5mm thick button wedge

of 80mm with tapered flanges of 26mm each

having clips of 10.5mm at 450mm centre to

centre shall be fixed in a direction

perpendicular to G.I. channel with

connecting clips made out of 2.64mm

diax230mm long G.I. wire at every junction

including fixing the gypsum board with

ceiling section and perimeter channels

0.5mm thick 27mm high having flanges of

20mm and 30mm long, the perimeter of

ceiling fixed to wall partition with the

help of rawl plungs at 450mm centre to centre with 25mm long

drive-all screws @ 230mm interval

including jointing and fixing to a flush

finish of tapered and square edges of the

board with recommended filler, jointing

tapes, finisher and two coats of primer

suitably for board as per manufactures

specification and also including the cost

of making openings for light fittings,

grills, diffusers, cutouts made with frame

of perimeter channels suitable fixed all

complete as per drawing and specification

and direction of the Engineer in Charge

but excluding the cost of painting with of 26

Rate in Rs. Amount

in Rs.

in figures in words


12.45.1 12.5mm thick tapered edge gypsum board

conforming to IS:2095-Part 1.

Sqm 410

6.11 Providing and fixing 100 mm wide vertical

venation blinds polyster fabric lourers

linked to each other with wane chain and

hanged with PVC hooks sliding on aluminium

guide rail, the control handles attached

to high strength polyster handle fibre

cord shall be moulded type and to be made

of steel ball chain, at the bottom of

lourers shall be of a glavanised steel

plate duly powder coated including fixing

to galvanized steel bracket on the top,

all complete

Sqm 20

6.12 Disposal of malba, building rubbish etc.

by mechanical transport including

loading, unloading and stacking for all

leads and lift complete as per direction

of Engineer-in-Charge

Cum 200

6.13 Providing and fixing UPVC panelled and

glazed doors & windows with frames.

Glazing with 5mm thick float glass on both

sides and pre-laminated board of 6mm thick

in bottom inside panel including fittings

and fixtures insulation material etc

complete. The window material should have

the property of with acoustic insulation,

thermal insulation,water tight, fire

resistant, termite resistant as per ISI/

BS specification of required shape, size

and design as per approval of Engineer-in-

charge.

Sqm 82

6.14 10.2 Structural steel work riveted, bolted or

welded in built up sections, trusses and

framed work, including cutting, hoisting,

fixing in position and applying a priming

coat of approved steel primer all complete

kg 810

of 26

Rate in Rs. Amount

in Rs.

in figures in words


SH-7.00 ALUMINIUM WORK

7.1 21.1 Providing and fixing aluminium work for

doors, windows, ventilators and partitions

with extruded built up standard tubular

sections/ appropriate Z sections and other

sections of approved make conforming to

IS: 733 and IS:1285, fixed with rawl plugs

and screws or with fixing clips, or with

expansion hold fasteners including

necessary filling up of gaps at junctions,

at top, bottom and sides with required PVC

/neoprene felt etc. Aluminium sections

shall be smooth, rust free, straight,

mitred and jointed mechanically wherever

required including cleat angle. Aluminium

snap beading for glazing/ panelling, C.P.

brass/ stainless steel screws, all

complete as per architectural drawings and

the directions of Engineer-in-charge

(Glazing and panelling to be paid for

separately)

21.1.1 For fixed portion

21.1.1.1 Abodised aluminium (anodised transparent

or dyed to required shade according to IS:

1868, Minimum anodic coating of grade AC

15)

Kg 23

7.2 21.1.2 For shutters of doors, windows &

ventilators including providing and fixing

hinges/ pivots and making provision for

fixing of fittings wherever required

including the cost of PVC/ neoprene gasket

required (Fittings shall be paid for

separately)

21.1.2.1 Abnodised aluminium (anodised transparent

or dyed to required shade according to

IS:1868, Minimum anodic coating of grade

AC 15)

Kg 45

of 26

Rate in Rs. Amount

in Rs.

in figures in words


7.3 21.2 Providing and fixing 12mm thick

prelaminated particle board flat pressed

three layer or graded wood particle boqard

conforming to IS:12823 Grade 1 Type II, in

panelling fixed in aluminium doors,

windows shutters and partition frames with

C.P. brass/ stainless steel screws etc.

complete as per architectual drawings and

directions of engineer-in-charge.

21.2.2. Pre-laminated particle board with

decorative lamination on both sides.

Sqm 4

7.4 21.3 Providing and fixing glazing in aluminium

door, window, ventilator shutters and

partitions etc. with PVC/ neoprene gasket

etc. complete as per the architectural

drawings and the directions of engineer-in-

charge (Cost of aluminium snap beading 21.3.2 With float glass panes of 5.50 mm

thickness

Sqm 4

7.5 21.4 Providing and fixing double action

hydraulic floor spring of approved brand

and manufacture IS:6315 marked for doors

including cost of cutting floors as

required, embedding in floors and cover

plates with brass pivot and single piece

M.S sheet outer box with slide plate etc.

complete as per the direction of Engineer-

in-charge

21.4.1 With stainless steel cover plate each 4

of 26

Rate in Rs. Amount

in Rs.

in figures in words


7.6 21.8 Filling the gap in between aluminium frame

& adjacent RCC/Brick/Stone work by

providing weather silicon sealant over

backer rod of approved quality as per

architectural drawings and direction of

Engineer-in-charge complete

21.8.1 Upto 5mm depth and 5mm width metre 240

7.7 21.12 Providing and fixing aluminium tubular

handle bar 32mm outer dia 3.0 mm thick &

2100 mm long with SS screws ect. Complete

as per direction of Engineer- in -Charge

21.12.1 Anodized (AC 15) aluminium tubular handle

bar

each 8

7.8 21.13 Providing and fixing 100mm brass locks

(best make of approved quality) for

aluminium doors including necessary

cutting and making good etc. complete

each 2

of 26

Rate in Rs. Amount

in Rs.

in figures in words


SH-8.00 SANITARY AND WATER SUPPLY

8.1 Water closed-p/fixing wall mounted

european type W.C pan Hindware make along

with cast iron wall cantilever brackets

,with seat cover,installing/connecting

into S.C.I pipe,water supply,p/fixing

concealed cistern and all connection

complete as per specification and

direction of engineer in charge(sample can

be seen for the same in DIMTS office).

each 4

8.2 Providing and fixing hindware riva urinal

with censor attachment within it etc.

complete as per specification and approval

of Engineer in charge (sample can be seen

for the same in dimts office).

each 2

8.3 P/F (hindware make kathy) rectangular wash

basin fixed into counter including CP

waste coupling with rubber plug, bottle

trap with long wall connection pipe and CP

inlet connection as per specification and

aprroval of E in charge.(sample can be

seen for the same in dimts office).

each 4

8.4 Providing and fixing Stainless Steel A

ISI 304(18/8) kitchen sink as per IS 13983

with C.I. brackets and stainless steel

plug 40 mm including painting of fittings

and brackets, cutting and making good the

walls wherever required.

Kitchen sink with drain board 510x1040mm

bowl depth 250mm

each 0

of 26

Rate in Rs. Amount

in Rs.

in figures in words


8.5 Providing and fixing mirror of superior

glass (of approved quality) and of

required shape and size with plastic

moulded frame of approved make and shade

with 6mm thick hard board backing.

Rectangular shape 1500x450mm each 2

8.6 Providing and fixing toilet paper holder

CP brass

each 4

8.7 Urinal partitions , providing and fixing

merino modesty pannels as per

specification and approval of Engineer in

charge.(sample can be seen for the same in

DIMTS office).

each 1

8.8 Providing and fixing PTMT liquid soap

container 109mm wide, 125mm high and 112mm

distance from wall of standard shape with

bracket of the same materials with snap

fittings of approved quality and colour,

weighing not less than 105 gms.

each 2

8.9 Angle cock: P/F Jaguar- florentine series

heavy body CP complete as per

specification and approval of E in charge.

each 8

8.10 Pillar Cock: P/F Jaguar PRESSMATIC series

heavy body CP make pillar cock with

adjustable wall flange etc . Complete as

per specification and approval of Engineer

in charge.

each 4

8.11 Jet spray: P/F hand shower (Health faucet

with 8 mm dia 1 meter long PVC tube wall

hook etc . Complete (make Jaguar

"florentine") as per specification and

approval of Engineer in charge.

each 4

of 26

Rate in Rs. Amount

in Rs.

in figures in words


8.12 17.35 Providing and fixing soil, waste and vent

pipes :

17.35.1 100 mm dia.

17.35.1.1 Sand cast iron S&S pipe as per IS: 1729. metre 50

8.13 17.37 Providing and fixing M.S. holder-bat

clamps of approved design to Sand Cast

iron/cast iron (spun) pipe embedded in and

including cement concrete blocks

10x10x10cm of 1:2:4 mix (1 cement : 2

coarse sand : 4 graded stone aggregate

20mm nominal size) including cost of

cutting holes and making good the walls

etc.

17.37.1 For 100 mm dia. Pipe each 10

8.14 17.41 Providing and fixing double equal junction

of required degree with access door,

insertion rubber washer 3 mm thick, bolts

and nuts complete :

17.41.1 100x100x100x100mm

17.41.1.1 Sand cast iron S&S as per IS - 1729 each 3

8.15 17.58 Providing lead caulked joints to sand cast

iron/centrifugally cast (spun) iron pipes

and fittings of diameter:

17.58.1 100 mm each 25

8.16 P/F CP brass Jali for floor traps 100 mm. each 5

of 26

Rate in Rs. Amount

in Rs.

in figures in words


8.17 Concealed pipe including painting with

anti corrosive bitumastic paint, cutting

chases and making good the wall

18.11.1 15 mm dia nominal bore metre 50

18.11.2 20 mm dia nominal bore metre 70

8.18 22.5 Providing and laying water proofing

treatment in sunken portion of WCs,

bathroom etc., by applying cement slurry

mixed with water proofing cement compound

consisting of applying : a) First layer of

slurry of cement @ 0.488 kg/sqm mixed with

water proofing cement compound @ 0.253

kg/sqm. This layer will be allowed to air

cure for 4 hours. b) Second layer of

slurry of cement @ 0.242 kg/sqm mixed with

water proofing cement compound @ 0.126

kg/sqm. This layer will be allowed to air

cure for 4 hours followed with water

curing for 48 hours. The rate includes

preparation of surface, treatment and

sealing of all joints, corners, junctions

of pipes and masonry with polymer mixed

slurry.

sqm 42

8.19 Granite Counter ( toilet and pantry) : P/F

counter made out of 25 mm thick granite (

of approved colour & shade supported by

20 mm thick Kadappa horizontally and 12

mm thick.Sandwiched Kaddappa vertically

at intervals as per specification and

approval of engineer in charge.

Sqm 4

of 26

Rate in Rs. Amount

in Rs.

in figures in words


8.20 Below Counter Storage: P/Constructin 1 mm

thick laminate shutters for electrical

pannels ,toilet and pantry counter

platform area with 3/4" thick marine ply

of Anchor/Kit ply or Kenwood make with

3/4" * 2 " Teak wood frame, shutter to

include.

sqm 3

SH: 9.00 FURNITURE

9.1 MR Supply of table of size 1800x900x750mm

using 25mm thick post form top and rest

18mm thick pre laminated particle board,

PVC side edge with all fittings and

fixtures complete as per direction of

Engineer-in-charge including

Each 8

(i) Pedestal unit of size

450x450x715mm(ht) under the table made of

25mm thick post form top and rest 18mm

thick pre-laminated particle board with

two equal drawers and one filling drawer

with centralized locking and castors duly

powdered coated in/c all fittings &

fixtures complete.

(ii)Side Storage: 1200x450x725mm (ht)


18mm thick pre laminated particle board

with PVC side edge bidding, metal key

board tray(pull out type

(iii) CPU trolley with W-180mm, D-245mm, H-

210mm made up of press formed MS CP sheet

1.6mm thick with adjustable width, rubber

pads inside the trolley for the safety of

CPU in/c castors and brakes with fittings

and fixtures complete.

of 26

Rate in Rs. Amount

in Rs.

in figures in words


9.2 MR Supply of table of size 1500x750x750mm


18mm thick pre laminated particle board,

PVC side edge with all fittings and

fixtures complete as per direction of

Engineer-in-charge including

Each 14








fixtures complete.

(ii)Side Storage: 900x450x725mm (ht) using


thick pre laminated particle board with

PVC side edge bidding, metal key board

tray(pull out type,

(iii) CPU trolley with W-180mm, D-245mm, H-






9.3 MR Suppl of work station table of size

1500mm x 750mm x 750mm, with key board

tray, expendable CPU trolly (Metal),

Pedestal unit under the working top using


thick pre-laminated particle board as per

specification of key board tray(Pull out

type), CPU Trolley & Pedestal unit are

given below with all fixture and fittings,

as per direction of Engineer-in-charge.

Each 7

of 26

Rate in Rs. Amount

in Rs.

in figures in words









fixtures complete.

(ii) CPU trolley with W-180mm, D-245mm, H-






9.4 MR Supply of storage unit of height 750mm and

depth 450mm using 25mm thick post form top

and rest 18mm thick pre- laminated

particle board for partitions storage,

doors etc. with PVC side edge beading and

all fittings & fixtures complete as per

direction of Engineer-in-charge( Note :

Area of storage shall be calculated

length multiplied by height of storage)

sq.m 30

of 26

Rate in Rs. Amount

in Rs.

in figures in words


9.5 MR Providing and fixing modular partition

69mm thick (± 4mm) made of M S profile

38x38mm. Medium horizontal profiles shall

run parallel inside the partition at 600mm

centre to centre and verticle profiles

shall be provided 750mm centre to centre

or as per site requirement with provision

of horizontal slots for taking wires as

required. All M.Sprofiles shall be powder

coated. Both sides of partition frame

shall be covered with 12mm thick pre

laminated particle board/ fabric mounted

on soft board /partly with 5.5mm thick

frosted float glass at top of required

height over particle board partitions as

required at site the particle board shall

be attached to the partition frame with

clips on the rear side. The end of

vertical member as well top member of

partition shall be fixed / covered with

powder coated aluminium member of 72mm

wide and 1.8mm thick complete as per

direction of Engineer-in-charge.

Sqm 115

9.6 MR Supply of high back chair, CRC steel

frame, padding Nivar & Hellical springs,

centre tilt, gas lift, Wooden Arms,

Upholstery in fabric/leatherite top

quality of approved shade and design,

cushion made of 60mm thick PU foam as per

specificationsas under and direction of

Engineer-in-charge

Overall Size: W-700mm, D-700mm, H-1060 to

1100mm

Adjustability of seat height 450mm to

540mm

Seat size:520x530mm (approx.)

Back size:480x520 (ht.) (approx.)

Each 10

of 26

Rate in Rs. Amount

in Rs.

in figures in words


Material of seat and back should be made

up of 12mm thick hot pressed ply wood,

moulded polyurethane foam with density 60,

together with moulded ABS seat and back

covers. The back foam is designed with

contoured lumbar support for extra

comfort. The seat and back are to be

covered with vacuum foam from 3mm thick

black ABS sheet. The chair should have

forward tilt, required board tilt with

tilt locking and anti shock back mechanism

with wooden arms. The twin wheel castors

should be injected moulded in black Nylon

and having 5 prongs are powder

coated/chrome plated base.

9.7 MR Supply of medium back chair, CRC steel


centre tilt, gas lift, Wooden Arms,

Upholstery in fabric/leatherite top

quality of approved shade and design,

cushion made of 60mm thick PU foam as per

specificationsas under and direction of

Engineer-in-charge

Overall Size: W-700mm, D-700mm, H-925mm to

975mm Adjustability of seat height 450mm


Back size:480x580mm (ht.) (approx.)

Each 24

of 26

Rate in Rs. Amount

in Rs.

in figures in words








comfort. The seat and back are to be


black ABS sheet. The chair should have







9.8 MR Supply of medium back chair, CRC steel


centre tilt, Wooden Arms, Upholstery in

fabric/leatherite top quality of approved

shade and design,cushion made of 40mm

thick PU foam as per specificationsas

under and direction of Engineer-in-charge

Overall Size: W-700mm, D-700mm, H-925mm to

975mm Adjustability of seat height 450mm


Back size:430x520mm (ht.) (approx.)

Each 18

of 26

Rate in Rs. Amount

in Rs.

in figures in words








comfort. The seat and backs are to be


black ABS sheets. The chair should have







of 26

Rate in Rs. Amount

in Rs.

in figures in words


9.9 MR Supply of low back chair, CRC steel frame,

padding Nivar & Hellical springs, centre

tilt, Nylon base PU arms, Upholstery in

fabric/leatherite top quality of approved

shade and design, cushion made of 40mm

thick PUfoam.as per specificationsas under

and direction of Engineer-in-charge

Overall Size: W-700mm, D-700mm,

Adjustability of seat height 450mm


Back size:430x340mm (Ht.)(approx.)







comfort. The seat and backs are to be


black ABS sheets. The twin wheel

castors should be injected moulded in

black Nylon and having 5 prongs are powder


Each 40

of 26

Rate in Rs. Amount

in Rs.

in figures in words


9.9 MR Supply of 3(three) seater, 2(two) seater,

single seater sofa with arms of size

2020mm (W)x750mm (D)x750mm(H) and seat

height 400mm for 3 seater, 1420mm

(W)x750mm(D)x750mm(H) for 2 seater and

1020mm(W)x 750mm(D)x 750mm(H) for single

seater with arms height 590mm. The sofa

structure is to be made of 45mmx28mm

finished Teak wood section with flat

vertical springs and 90mm thick 40 density

PU foam with topping of 20mm super soft

foam, back is to be made with 45mm thick

32 density PU foam with topping of 20mm

super soft foam . Armed structure is to

be made with 120x28mm teak section for top

and vertical, 95x28mm for bottom. Arms

are to be covered with 20mm thick 28

Each 2

foam all side.Armed and back loose cushion

are mde of 45mm thick 32 density PU foam

with legs made out of 70x70mm teak section

in round shape with 45mm height and good

quality tapestry/leatherite, malemine

polish etc. or as per size required at

site with all fittings and fixtures.

Complete as per direction of Engineer-in-

charge

9.10 Supply of Center Table of size

1200x600x450mm made of teak wood duly

spirit polish with 75x75mm teak wood legs

and 12mm thick bevelled edge glass top

or18mm thick pre laminated MDF board

lipping the edge banding of pre glued tape

of same shade by hot process or as per the

design approved by Engineer in-charge

Each 1

of 26

Rate in Rs. Amount

in Rs.

in figures in words


9.11 MR Supply of Conference Table of required

shape of over all size 3600x1200x750mm(ht)

comprising with three units of size

1200x1200x750mm (ht) using 25mm thick post

form pre laminated particle board top

supported with metal powder coated

legs/chrome plated in approved shade with

necessary fittings and fixtures complete

as per directions of Engineer-in-charge.

All the four corners should be covered

with half round top and all the tables

are to be covered with front panels.

Each 1

TOTAL

of 26

BILL OF QUANTITIES - ELECTRICAL WORKS


Part 'A' Composite work of modular partitions, modular furniture, UPVC windows & Civil, Electrical & Fire Fighting works

Rate in Rs. Amount

in Rs.

in figures in words

SUB HEAD :- A, INTERNAL WIRING

I POINT WIRING

1.0 Wiring for light point/ fan point/ exhaust

fan point/ call bell point with 1.5 sq.mm FR

PVC insulated copper conductor single core

cable in surface / recessed steel conduit,

with modular switch, modular plate, suitable

GI box and earthing the point with 1.5 sq.mm.

FR PVC insulated copper conductor single core

cable etc as required.

GROUP-C 172 Point

2.0 Wiring for twin control light point with 1.5

sq.mm FR PVC insulated copper conductor

single core cable in surface / recessed steel

conduit, 2 way modular switch, modular plate,

suitable GI box and earthing the point with

1.5 sq.mm. FR PVC insulated copper conductor

single core cable etc as required.

2 Point

3.0 Wiring for light/ power plug with 2X4 sq. mm


cable in surface/ recessed steel conduit

alongwith 1 No 4 sq. mm FR PVC insulated

copper conductor single core cable for loop

earthing as required.

350 Meter

4.0 Wiring for light/ power plug with 4X4 sq. mm


cable in surface/ recessed steel conduit

alongwith 2 Nos 4 sq. mm FR PVC insulated

copper conductor single core cable for loop

earthing as required.

300 Meter

5.0 Supplying and fixing suitable size GI box

with modular plate and cover in front on

surface or in recess, including providing and

fixing 3 pin 5/6 amps modular socket outlet

and 5/6 amps modular switch, connection,

painting etc. as required. (For light plugs

to be used in non residential buildings).

48 Each

Item No Description Qty Unit

Page 1 of 10

Rate in Rs. Amount

in Rs.

in figures in words


6.0 Supplying and fixing suitable size GI box

with modular plate and cover in front on

surface or in recess, including providing and

fixing 6 pin 15/16 & 5/6 amps modular socket

outlet and 15/16 amps modular switch,

connection, painting etc. as required.

19 Each

7.0 Supplying and fixing call bell/ buzzer

suitable for D.C./A.C. single phase, 230

volts, complete as required.

0 Each

8.0 Supply and fixing fan box (hexagonal type) as

per drg. Attached 75 mm side 75mm deep made

of 16 SWG M.S. sheet having 6 Nos. knockouts

of size 20/25 mm for conduit entry including

fan hook made of 12mm M.S. Rod with bottom

cover of 3mm thick phenolic laminated sheet,

painting etc. as required.

22 Each

II CIRCUIT /SUBMAIN WIRING

1.0 Wiring for circuit/ submain wiring alongwith

earh wire with the following sizes of FR PVC

insulated copper conductor, single core

cable in surface/ recessed steel conduit as

required

a) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 750 Meter

b) 4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire 20 Meter

c) 4 X 6 sq. mm + 2 X 6 sq. mm earth wire 20 Meter

d) 4 X 10 sq. mm + 2 X 10 sq. mm earth wire 20 Meter

SUB HEAD-B: LUMINARIES AND FIXTURES

I SUPPLY OF LUMINARES

1.0 Supply of the following luminaires complete

in all respects

a) LED Strip light, Instapower Slim sparkle 8W

or equivqlent

70 m

b) LED ceiling light 45W, Instapower Milkyway or

equivalent

8 Nos

c) LED Downlighter 11W, Instapower D-Lite 119 Nos

Page 2 of 10

Rate in Rs. Amount

in Rs.

in figures in words


d) Attractive wall mounted light fixture with 1x

PL -S 11 W CFL lamp. Philips Cat No. FMC

170/111 or equivalent.

0 Nos

II SUPPLY OF CEILING/ PROPELLER TYPE EXHAUST

FANS (WITH GRAVITY LOUVERS) / CABIN FAN.

a) 1200 mm sweep Ceiling fan. 22 Nos

b) 300 mm dia 900 RPM exhaust fan. 2 Nos

d) Supplying and fixing stepped type electronic

fan regulator on the existing modular plate

switch box including connections but

excluding modular plate etc. as required.

22 Each

III INSTALLATION OF LUMINARIES AND FIXTURES

a) Installation, testing and commissioning of

pre-wired, fluorescent fitting / compact

fluorescent fitting of all types, complete

with all accessories and tube etc. directly

on ceiling/ wall, including connection with

1.5 sq. mm FR PVC insulated, copper

conductor, single core cable and earthing

etc. as required.

148 Each

b) Installation, testing and commissioning of

ceiling fan, including wiring the down rods

of standard length (upto 30 cm) with 1.5 sq.

mm FR PVC insulated, copper conductor, single

core cable, including providing and fixing

phenolic laminated sheet cover on the fan box

etc. as required.

22 Each

c) Installation of exhaust fan upto 450 mm sweep

in the existing opening, including making the

hole to suit the size of the above fan,

making good the damage, connection, testing,

commissioning etc. as required.

2 Each

d) Extra for fixing the louvers/ shutters

complete with frame for a exhaust fan of all

sizes.

2 Each

SUB HEAD -C, DISTRIBUTION BOARDS

I DISTRIBUTION BOARDS

Page 3 of 10

Rate in Rs. Amount

in Rs.

in figures in words


1.0 Supplying and fixing following way, three

pole and neutral, sheet steel, MCB

distribution board, 415 volts, on surface/

recess, complete with tinned copper busbar,

neutral busbar, earth bar, din bar,

detachable gland plate, interconnections,

phosphatized and powder painted including

earthing etc. as required. (But without

MCB/RCCB/Isolator)

a) 4 way (4 + 12), Double door, horizontal type 1 Each

b) 6 way (4 + 18), Double door, horizontal type 1 Each

c) 8 way (4 + 24), Double door, horizontal type 2 Each

2.0 Supplying and fixing 5 amps to 32 amps

rating, 240 volts, 'B' series, miniature

circuit breaker suitable for lighting and

other loads of following poles in the

existing MCB DB complete with connections,

testing and commissioning etc. as required.

a) Single Pole 78 Each

3.0 Supplying and fixing single pole blanking

plate in the existing MCB DB complete etc. as

required.

20 Each

4.0 Supplying and fixing following rating, four

pole, (three phase and neutral), 415 volts,

residual current circuit breaker (RCCB),

having a sensitivity current upto 300

milliamperes in the existing MCB DB complete

with connections, testing and commissioning

etc. as required.

a) 63 A 4 Each

SUB HEAD - D :- TELEPHONE / TV & DATA

SYSTEM

1.0 Supplying and drawing following pair, 0.5 mm

dia FR PVC insulated copper conductor,

unarmored telephone cable in the existing

surface/ recessed steel/ PVC conduit as

required.

a) 2 Pair 1000 Meter

Page 4 of 10

Rate in Rs. Amount

in Rs.

in figures in words


2.0 Supplying and drawing co-axial TV cable RG-6

grade, 0.7 mm solid copper conductor PE

insulated, shielded with fine tinned copper

braid and protected with PVC sheath in the

existing surface/ recessed steel/ PVC conduit

as required.

25 Meter

3.0 Supplying and fixing of following sizes of

PVC conduit along with accessories in

surface/ recess including cutting the wall

and making good the same in case of recessed

conduit as required.

a) 20 mm. 200 Meter

b) 25 mm. 600 Meter

4.0 Supplying and fixing following modular

switch/ socket on the existing modular plate

& switch box including connections but

excluding modular plate etc. as required.

a) Telephone socket outlet. 22 Each

b) TV antenna socket outlet. 1 Each

5.0 Supplying and fixing following size/ modules,

GI box along with modular base & cover plate

for modular switches in recess etc as

required.

a) 1 or 2 Module (75mm x 75mm) 45 Each

6.0 Supply and fixing following Data /Lan modular

socket on the existing modular plate

including connections but excluding modular

plate etc. as required.

a) RJ - 45 Socket. 22 Each

7.0 Supply of UTP Cat 6 Data /Lan wiring

cable for computer communication (Data / Lan

wiring) system in the existing surface /

recessed steel / PVC conduit as required.

a) 1 No. 900 Meter

Page 5 of 10

Rate in Rs. Amount

in Rs.

in figures in words


8.0 Supply and fixing of the following Telephone

Tag Block made out of M.S sheets of 18 SWG

thickness properly welded complete with all

accessories such as Tag block, connector

(KRONE make), mounting strips, tapped holes,

fixing bolts, approved shad of paint after

primer as per specifications.

a) 50 Pair 1 Nos.

b) 10 Pair 1 Nos.

9.0 Supply & fixing of 14 SWG under floor box

alongwith 10SWG stainless steel cover plate.

a) 350 x 350 x 50 mm deep 1 Nos.

b) 300 x 300 x 50 mm deep 1 Nos.

c) 250 x 250 x 50 mm deep 1 Nos.

d) 200 x 200 x 50 mm deep 1 Nos.

e) 150 x 150 x 50 mm deep 1 Nos.

f) 100 x 100 x 50 mm deep 1 Nos.

SUB HEAD - E , L.T. PANELS (SUPPLY AND

INSTALLATION)

1.0 L.T. PANELS :

Page 6 of 10

Rate in Rs. Amount

in Rs.

in figures in words


1.1 Supply of the following cubical type panels

made of 14 guage CRCA structure, base

channel, complete with, moulded case circuit

breakers, meters, indicating lamps, current

transformer etc. Complete in all respects,

insulated bus bars with heat shrinkable PVC

sleeve in suitable bus chambers,

interconnection, small wiring, name plate,

danger plat, earth bus etc. & comprising of

compartments with hinged door for each feeder

& its accesories, cable alley with hinged

doors, bus chamber with bolted door etc. The

panel being of dust & vermin proof

construction with rubber gasket attractively

powder coating etc. The panel shall be free

standing type/ wall mounted type as per

relavant drawing and comprising with the

following.

Note:-

1 All MCCBS shall be with operating handle.

2 CTs burden shall be 15VA & accuracy class 1.0

3 CTs shall be cast resin type .

4 All MCCBs shall be with thermal magnetic/

Microprocessor based releases.

5 All indication lights shall be LED type.

6 All meter shall be digital type.

7 Rated Short Time withstand current of all

MCCB's are Icw for one second.

8 Breaking Capacity of all MCCB's are Ics

service breaking capacity

A) MAIN L. T. PANEL (MLTP)

a) INCOMING :

i) 2 Nos.200A TP MCCB (35kA)

1No. 200A Changeover

b) BUS BAR :

i) One set of 300A Alu. Bus Bar with PVC Sleeve

in sealed M.S. Painted bus chamber.

c) METERING , INDICATIONS AND RELAYS :

i) 1 set. of R/ Y/ B phase indicating lamp with

control MCB's.

ii) 1 No. (0 - 300A) Digital Ammeter with built-

in selector switch and CT's.

iii) 1 No . (0 - 500 V) Digital Voltmeter with

built-in Selector switch & control MCB's.

d) OUT GOINGS :

i) 2 Nos. 100A, TP MCCB (25 kA)

ii) 6 Nos. 63A, 4P MCB (10 kA)

1 Set

Page 7 of 10

Rate in Rs. Amount

in Rs.

in figures in words


e) ON-OFF indication lamps shall be provided on

all outgoing feeders

f) 1 No. 50 x 6mm Aluminium Earth Bus across the

width of the panel.

B) MAIN UPS PANEL BOARD

i) INCOMING :

ii) 1 No.100A, TP MCCB (25 kA)

ii) BUS BAR :

i) One set of 100A TPN Cu. Bus Bar with PVC

Sleeve in sealed M.S. Painted Bus

Chamber.(Neutral Bus Bar & Neutral links of

MCCB's shall be double of phase bus bar)

iii) INDICATIONS :

i) One set of R/Y/B phase indication lamp with

control fuse.

iv) OUTGOING :

i) 3 Nos 63 A TP MCCB (10kA)

g) 1 No. 40 x 5 mm Aluminium Earth Bus across

the width of the panel.

SUB HEAD - F , L.T. CABLES

1.0 L.T. CABLES (SUPPLY)

1.1 Supply of the following 1100 Volts Alu/ Cu.

Conductor, PVC insulated PVC sheathed, steel

armoured/ unarmoured or XLPE cables as per IS-

1554/ 7098 Part- I and as per stanard

specification

A) ALUMINIUM CABLE (ARMOURED)

a) 3.5 core 185 sq.mm XLPE 150 RM

b) 4 core 50 sq.mm PVC 30 RM

B) COPPER CABLES (ARMOURED)

a) 4 core 10 sq. mm. 50 RM

b) 4 core 6 sq. mm. 15 RM

1.0 L.T. CABLES (INSTALLATION)

1.1 Laying and fixing of one number PVC insulated

and PVC sheathed/ XLPE Aluminium / Copper

conductor cable of 1.1 KV grade on surface

as required.


a) 3.5 core 185 sq.mm XLPE 150 RM

b) 4 core 50 sq.mm PVC 30 RM


1 Set

1 Set

Page 8 of 10

Rate in Rs. Amount

in Rs.

in figures in words


a) 4 core 10 sq. mm. 50 RM

b) 4 core 6 sq. mm. 15 RM

2.0 CABLE END TERMINATIONS

2.1 Supply & provide cable end terminations for

following Aluminium/Copper conductor cables

using crimping sockets, brass compression

glands, etc, as required.


a) 3.5 core 185 sq.mm XLPE 2 Nos

b) 4 core 50 sq.mm PVC 2 Nos


a) 4 core 10 sq. mm. 10 Nos

b) 4 core 6 sq. mm. 4 Nos

SUB HEAD - G , EARTHING & MISCELLANEOUS ITEMS

1.0 TAPES/WIRES

Supplying, receiving, laying, fixing,

jointing, and terminating of the following

tapes/wires in masonry treches/on walls/on

cable tray/ along the cable with suitable

G.I./Copper Clamps, screws etc. The wire

shall be terminated with proper thimbles,

washers, bolts & nuts. All joints shall be

regid using double rivites :

a) 40 x 5 mm GI Tape 50 RM

b) 1Core x 6 mm CU Flexible wire 20 RM

c) 1Core x10 mm CU Flexible wire 20 RM

2.0 EARTH STATIONS:

2.1 Providing and fix following earth station as

per IS 3043-1987, with watering pipe, GI

funnels masonry chamber with CI cover,

Including excavation and refilling of pit,

supplying and fixing of charcoal salt &

sand, identification of pit as as required.

Page 9 of 10

Rate in Rs. Amount

in Rs.

in figures in words


a) 600 x 600 x 3.15 mm Copper Plate Earth Station 1 Nos.

b) 600 x 600 x 6.00 mm GI Plate Earth Station 1 Nos.

TOTAL

Page 10 of 10

BILL OF QUANTITIES - FIRE FIGHTING WORKS


Part 'A' Composite work of modular partitions, modular furniture, UPVC windows & Civil, Electrical & Fire Fighting works

Rate in Rs. Amount in Rs.

in Rs.in figures in words

1 Supply,installation and commissioning of semi

concealed pendant type sprinkler 68°C complete

with crome steel sliding type rosette in the

existing network including M.S pipe of 15 mm dia

sized upto 1.5 m length as required including

fittings consumable etc. complete.

each 20

2 Supply,installation and commissioning of optical

smoke detector standard design with wall mounting

based in the existing fire alarm system complete

(agni or system sensor make).

each 60

3 Supply, installation and commissioning of

response indicator on ceiling / walls ,including

connections etc. in the existing fire alarm

system complete (agni or system sensor

make).

each 40

4 Supply, installation and commissioning of copper

conductor PVC insulated heavy duty armoured cable

of havell make as per approval of Engineer in

charge The following sizes

a)2*1.5 sqmm metres 200

b)4*1.5 sqmm metres 35

5 Supply, installation and commissioning of sounder

(hooter) standard make (such as agni or system

sensor make) in the existing fire alarm system

each 2

6 Supply, installation testing and commissioning of

manual call boxes complete of standard make (agni

or system sensor make) with hammer and chain

including connection etc.as required

each 8

7P/F G.I. pipes complete with G.I. fittings and

clamps including cutting and making good the

walls a)15mm nominal bore

metres 25

b)25mm nominal bore metres 10

8 Dismentling of existing 25 mmMS pipes& refixing the same after making

necessary adjustment in sprinklers including testing of sprinklers complete

as per the direction of engineer-in-charge. metres 25


Page 1 of 1

BILL OF QUANTITIES - CIVIL WORKS RENOVATION OF · PDF filePart 'A' Composite work of modular...

Documents

Transcript of BILL OF QUANTITIES - CIVIL WORKS RENOVATION OF · PDF filePart 'A' Composite work of modular...