BENTEC SOFT TORQUE ROTARY SYSTEM (STRS) MK III STRS_1108.pdfTop Drive or Rotary Table, DC or AC •...
Transcript of BENTEC SOFT TORQUE ROTARY SYSTEM (STRS) MK III STRS_1108.pdfTop Drive or Rotary Table, DC or AC •...
![Page 1: BENTEC SOFT TORQUE ROTARY SYSTEM (STRS) MK III STRS_1108.pdfTop Drive or Rotary Table, DC or AC • No additional sensors on the rig • Interfacing to existing SCR or VFD Drive system](https://reader036.fdocuments.in/reader036/viewer/2022070217/61218d1004b433456e166d8f/html5/thumbnails/1.jpg)
The Bentec Soft Torque Rotary System (STRS)
MK III is a self adjusting system with incorporated
vibration analyser for optimal drilling parameters.
It is designed to dampen drill string torsional
vibrations. It differs from previous systems in its
operation and tuning procedure being based on a
mathematical model of the entire rotary system.
This warrants optimum damping performance
under all conditions.
In addition the system features microprocessor-
assisted adjustment, providing great ease of
handling. No inputs from the driller to be done.
Switch it on and the system does its work.
The STRS-Output-Signal modifies the electronic
speed control of the drive. The output-Signal is
precisely calculated taking into account behaviour
and conditions of drill string and drive system
dynamics. These set parameters, result in signifi-
cant reduction of torque fluctuations, torsional drill
string vibrations and stick slip behaviour.
The system can be easily installed as it does not
require any additional sensors.
For existing Soft Torque Rotary Systems MK II an
upgrade kit is available.
What does Mark III better than Mark II ?
- It operates automatically without any
manual adjustment
- It produces its own best parameters
STRS
_110
8
I
Rig Building Mechanics Electrics Repair Consulting Quality Projects Engineering
B E N T E C S O F T T O R Q U ER O TA R Y S Y S T E M ( S T R S ) M K I I I
Self adjust ing system with incorporated vibrat ionanalyser for opt imal dr i l l ing parameters
![Page 2: BENTEC SOFT TORQUE ROTARY SYSTEM (STRS) MK III STRS_1108.pdfTop Drive or Rotary Table, DC or AC • No additional sensors on the rig • Interfacing to existing SCR or VFD Drive system](https://reader036.fdocuments.in/reader036/viewer/2022070217/61218d1004b433456e166d8f/html5/thumbnails/2.jpg)
Effect of STRS MK III
T R A I N I N GTraining can be done either in our facilities in
Bad Bentheim or at site on the unit.
S E R V I C EProfessional service like system test, customer
acceptance, installation, commissioning, customer
training and after sales is available. Our customer
care service is on standby at any time via our service
hotline
+49-5922-72-354 (during business hours) and
+49-5922-72-111 (outside business hours).
T E C H N I C A L D A T A
Typical dimensions : (W x H x D mm)
Control Cabinet : 600 x 380 x 370
HMI Terminal : 297 x 200 x 80
Tailor-made solutions are available on request!
Supply of Voltage: 110 -240 V 50 / 60 Hz
Drillers Switch : ON / OFF Ex proof
A D V A N T A G E S :• It improves the bore hole quality
• It increases the rate of penetration
• It reduces the drill bit wear
• It saves the number of roundtrips
• It eliminates the stick-slip
• It dampens the drill string vibrations
• It extends the top drive capacity
• Suitable to all rigs with electrically driven
Top Drive or Rotary Table, DC or AC
• No additional sensors on the rig
• Interfacing to existing SCR or VFD Drive system
Upgrade Kit MK II to MK III Human Machine Interface (HMI)
www.bentec.comBentec GmbH Dri l l ing & Oi l f ield SystemsDeilmannstrasse 148455 Bad Bentheim • Germany
Contact: +49 5922 72 80 E-Mail: [email protected]