Beep Plans Complete

9
Plans- Assembly Manual Copyright 1972 by C.F. Struck Corp. These Plans are sold solely for non-Commercial purposes and their sale in no way licenses any individual or firm to reproduce the Mini- Beep in any form for resale. To do so will constitute direct violation of all pat- ents applicable at that time. To reproduce these Plans and Instructions in any form will constitute direct violation of our Copyright. C. F. STRUCK CORP.

Transcript of Beep Plans Complete

Page 1: Beep Plans Complete

Plans- Assembly Manual

Copyright 1972 by C.F. Struck Corp.

These Plans are sold solely for non-Commercial purposes and theirsale in no way licenses any individual or firm to reproduce the Mini- Beepin any form for resale. To do so will constitute direct violation of all pat-ents applicable at that time.

To reproduce these Plans and Instructions in any form will constitutedirect violation of our Copyright.

C. F. STRUCK CORP.

Page 2: Beep Plans Complete

PARTS LIST - B1200 BEEP

B1200 - 101 Bar (2)102 Axle (2)103 Shaft (2)104 Hub104A Front Hub (2)104B Rear Hub (2)105 Counter-Weight (6)106 Idler - 18 tooth 3/8 bore (2)107 Front Drive Chain - #40, 70-1/2" plus connector (2)108 Rear Drive Chain - #40, 39-1/2" plus connector (2)109 Wheel - 16 x 7. 50 Tire on 4 bolt 4" BC Rim (4)

Snap Ring 7/8 - . 675 ID (4)Snap Ring 7/8 - . 821 ID (2)WI Washer 3/8 (25)WI Washer 7/8 x 18 ga. (66)Locknut 3/8-16 (6)Lug Bolt 1/2-20x3/4 (16)Cap Screw 3/8-16 x 2 (2)Cap Screw 3/8-16x2-1/4 (4)

Assembly Instructions - B1200 Beep

NOTE: The "Beep" was specifically designed to completely utilize the Main Bodyand Drive Train of our standard MD1200 Series Tractor and therefore you are to usethe MD1200 Instruction Manual for the majority of your assembly. The followingInstructions are to be used as additions or substitutions to the standard MD1200 In-structions (enclosed) as described below.

ASSEMBLY: (Substitute the following for steps No. 1, 2, 3, 6 and 7 in MD1200Instructions)

1. Slide one #102 Axle through 7/8" holes in rear of Body. Slide second Axle throughforward slots in Body. Center Axles in Body. With the 3/8 wide x 2-1/2 long slot for-ward, slide each #101 Bar over its respective front and rear Axle ends on each side ofBody and slide up tight against the Body's Walls. Note - collars on #101 Bars are tothe outside.

2. Check and recenter Axles so their ends protrude out equally from Collars on eachside of Body. Tighten the four collar set screws.

3. Slide the 7 2 tooth Sprocket ends of #104B Rear Drive Hubs onto their respectiveends of the Rear Axle. Slide thirteen 7/8 WI Washers over each of the protruding endsof the Front Axle. Similarly slide the 72 tooth Sprocket ends of #104A Front DriveHubs onto their respective ends of the Front Axle. With 7/8 WI Washers shim outends of Front and Rear Axles and secure with 7/8 Snap Rings.

Page 3: Beep Plans Complete

(Follow steps No. 4 and 5 in MD1200 Instructions)

6. Slide 7/8 Snap Ring onto end of each #103 Shaft and engage it into its respective"groove". Slide seven 7/8 WI Washers onto the end of each #103 Shaft. From outsidethe Body insert each Shaft into the Oilite bushings in #10 Bearings. Take a straightedge and align the faces of the 72 tooth sprocket on the #104B Rear Hub with the 8 toothsprocket (sprocket closest to Body) on the #103 Shaft. This alignment can be accom-plished by adding or removing 7/8 WI Washers from the #103 Shaft.

7A. On each side of Tractor Body wrap the #108 Rear Drive Chain around the "inside"8 tooth sprocket (sprocket closest to Body) on #103 Shaft and around the 72 tooth sprock-et on #104B Rear Hub - secure with connector link. Draw up on each #10 Bearing As- 'sembly and secure by now tightening the six 5/16-18 Locknuts on each #10 Bearing.

7B. Insert each 3/8-16 x 2 Cap Screw into a 3/8 WI Washer and then into 3/8 bore ofeach #106 Idler. Follow with nine 3/8 WI Washers over end of each Cap Screw and in-sert end of Cap Screw into respective 3/8" slot of each #101 Bar. Secure on inside ofeach #101 Bar with 3/8 WI Washer and 3/8-16 Locknut - leave nut loose enough to slidein slot.

7C. On each side of Tractor Body wrap the #107 Front Drive Chain around the 8 toothsprocket (on "outside" of #103 Shaft) and the 7 2 tooth sprocket on #104A Front Hub andsecure with connector link. Loop the lower strand of #107 Chain over the #106 Idlerand tighten the Chain by pushing the #106 Idler forward. Secure Idlers on each side bytightening the 3/8-16 Locknuts.

7D. Using one of the #105 Counterweights as a templet, align the two 3" spaced 3/8loles in #105 Weight with the two 3" spaced 3/8 holes in lower rear underside ofTractor's #1G Pan. Center #105 Weight on the Pan and locate and drill the two re-maining 3/8 holes in Pan. Using four 3/8-16 x 2-1/4 Cap Screws and Locknuts installthe six #105 Weights "sandwich fashion" onto the underside of #1G Pan.

7E. Mount the four #109 Wheels onto their respective #104A & B Front and Rear Hubsand secure with 1/2-20 x 3/4 Lug Bolts.

Page 4: Beep Plans Complete
Page 5: Beep Plans Complete
Page 6: Beep Plans Complete
Page 7: Beep Plans Complete
Page 8: Beep Plans Complete
Page 9: Beep Plans Complete