Beam UHP170 & UHP250 Ultra High Pressure Washer€¦ · Beam UHP170 & UHP250 Ultra High Pressure...

8
Beam UHP170 & UHP250 Ultra High Pressure Washer Runway Rubber Removal - Painted Line Removal - Surface Texturing

Transcript of Beam UHP170 & UHP250 Ultra High Pressure Washer€¦ · Beam UHP170 & UHP250 Ultra High Pressure...

Page 1: Beam UHP170 & UHP250 Ultra High Pressure Washer€¦ · Beam UHP170 & UHP250 Ultra High Pressure Washer Runway Rubber Removal - Painted Line Removal - Surface Texturing 1122365 UHP170

Beam UHP170 & UHP250Ultra High Pressure WasherRunway Rubber Removal - Painted Line Removal - Surface Texturing

1122365 UHP170 - UHP250 Brochure GB.indd 2 24/09/12 07.42

1122365-UHP-Brochure-GB_210x297mm.pdf - 07:45:01 - September 24, 2012 - Page 1 of 8 - Coated preflight

Page 2: Beam UHP170 & UHP250 Ultra High Pressure Washer€¦ · Beam UHP170 & UHP250 Ultra High Pressure Washer Runway Rubber Removal - Painted Line Removal - Surface Texturing 1122365 UHP170

2

LeftUHP250 with optional sweeping equipment and extra water tank

MiddleHammelmann HDP174 pump

RightHammelmann HDP254 pump

Left and right bottom2500mm rotorcleaner with 5 rotating ‘heads’

UHP170 and UHP250The Beam Ultra High Pressure (UHP) washer is offered in two

variants, the standard 170KW model and a high power 250KW

version. Both machines have a variety of applications – including

runway rubber removal, painted line removal, and surface texturing.

They can be equipped with different high pressure cleaning heads

to suit each application – allowing the width of clean to be varied

between 300mm and 2500mm.

Both machines are mounted on either 3 or 4 axle chassis.

They have 14m³ stainless steel hoppers containing:

• Fresh water tanks

• A waste tank

• The ultra high pressure water pump

• A powerful fan driven vacuum system to collect waste.

The machines are powered from the chassis engine driven through

a hydrostatic gearbox. A CAN control system monitors and controls

the operation of the water system, the vacuum waste collection

system and an array of different cleaning heads and other optional

equipment. This allows the machine to be operated by 1 driver from

the chassis cab.

1122365 UHP170 - UHP250 Brochure GB.indd 3 24/09/12 07.42

1122365-UHP-Brochure-GB_210x297mm.pdf - 07:45:04 - September 24, 2012 - Page 2 of 8 - Coated preflight

Page 3: Beam UHP170 & UHP250 Ultra High Pressure Washer€¦ · Beam UHP170 & UHP250 Ultra High Pressure Washer Runway Rubber Removal - Painted Line Removal - Surface Texturing 1122365 UHP170

3

Left topUHP250 with 2500mm rear rotor system

Right topFront mounted 500mm rotor system removing coating from road surface

Left and right350mm rotor removing paint

Rotorcleaning Heads – rotating

spray bar systems

The UHP170 and UHP250 are equipped as standard with rear mounted rotorcleaning heads

for jetting large surface areas – for example for runway rubber removal or road surface

texturing. The UHP250 has a 2500mm wide system containing 5 rotor heads in a partially

overlapping configuration using 110 nozzles positioned to ensure an even application of

water to the surface. The UHP170 is equipped with a 1500 mm wide system using 3 heads

in a similar configuration.

For the cleaning of smaller or narrow surfaces – such as painted line removal, a variety of

optional front or side mounted rotorcleaning heads are available.

Working width Number of joints

300mm – optional 1

350mm – optional 1

500mm – optional 1

1500mm – standard on UHP174 3

2500mm – standard on UHP254 5

Rotorcleaning Systems

1122365 UHP170 - UHP250 Brochure GB.indd 4 24/09/12 07.42

1122365-UHP-Brochure-GB_210x297mm.pdf - 07:45:13 - September 24, 2012 - Page 3 of 8 - Coated preflight

Page 4: Beam UHP170 & UHP250 Ultra High Pressure Washer€¦ · Beam UHP170 & UHP250 Ultra High Pressure Washer Runway Rubber Removal - Painted Line Removal - Surface Texturing 1122365 UHP170

4

The UHP Water PumpsHammelmann has over 50 year’s experience in the construction of UHP pumps that are

used in some of the most arduous environments worldwide. The Hammelmann service

network is extensive – with service centres also located worldwide. The HDP174 and

HDP254 are vertical pumps of 3 and 5 cylinders respectively, featuring:

• Stainless steel stress free pump heads

• Bellows that form a hermetic seal between the suction chamber and crank section

• Solid tungsten carbide plungers

• Bronze suction chambers

• Integral speed reduction gears

• Pressurised oil lubrication systems with oil cooler and filter

The UHP pumps are driven directly from the chassis gearbox. An optional splitter valve can

vary the flow between 37 and 57 litres/min with the UHP250 and between 14 And 34 litres

/min with the UHP170. Pressure and flow can also been controlled via the gearbox.

LeftDiagram showing position of hydrostatic gearbox (pictured right) within the chassis subframe

RightPCH gearbox

BottomA UHP250 with optional extra 2000 litre water tank between cab and hopper and optional sweeping system located between the axles

1122365 UHP170 - UHP250 Brochure GB.indd 5 24/09/12 07.42

1122365-UHP-Brochure-GB_210x297mm.pdf - 07:45:15 - September 24, 2012 - Page 4 of 8 - Coated preflight

Page 5: Beam UHP170 & UHP250 Ultra High Pressure Washer€¦ · Beam UHP170 & UHP250 Ultra High Pressure Washer Runway Rubber Removal - Painted Line Removal - Surface Texturing 1122365 UHP170

In cab control panels placed around the driving position allowing for easy control and monitoring of all the machine’s functions

Far left Key components of the control system located in easily accessed waterproof locker

Control Centre

The CAN control system has been designed for ease of use and

monitoring of the various functions during operation including:

fan speed, oil and water temperature, oil pressure and providing

a summary of the brush gear (or other optional equipment) in

operation. The user friendly control panels are linked to the CAN

controller located under the hopper in an IP66 waterproof locker.

These controllers communicate with all the machine´s sensors and

control valves and ensure all the safety interlocks are functioning.

The controllers and programming language use a Sauer- Danfoss

system also used by: Claas, Caterpillar, Case New Holland, Landini

Manitou, Putzmeister, Merlo, Kalmar, Cargo Tec, Rolls Royce Marine

and Lännen.

Coverage

Beam UHP machines are equipped with the most powerful water

pumps available. Through well tested systems using CAN controls

and the latest water jet technology, the Beam UHP can offer very

high levels of coverage with little or no adverse effects on the

underlying surface.

5

Typical coverage – m2/hour

UHP170 1500mm rotor width 300 – 1200m²/hour

UHP250 2500mm rotor width 500 – 2000m²/hour

1122365 UHP170 - UHP250 Brochure GB.indd 6 24/09/12 07.42

1122365-UHP-Brochure-GB_210x297mm.pdf - 07:45:17 - September 24, 2012 - Page 5 of 8 - Coated preflight

Page 6: Beam UHP170 & UHP250 Ultra High Pressure Washer€¦ · Beam UHP170 & UHP250 Ultra High Pressure Washer Runway Rubber Removal - Painted Line Removal - Surface Texturing 1122365 UHP170

Waste Hopper, Water Tanks and Vacuum SystemThe waste hopper and water tanks are constructed from grade 304 stainless steel.

A hydrostatically powered fan system creates a strong vacuum that draws waste water

and debris into the hopper via nozzles on the ground that are integrated within the

rotorcleaning heads. The maximum vacuum is 1,800mm water with an airflow of 30,000

m³ per hour. The waste hopper is emptied through a pneumatically operated rear door by

tipping hydraulically.

Optional EquipmentMachines can also be equipped with a combination of additional options. Examples include:

• Runway and apron sweeping systems

• Cleaning of surface areas prior to UHP water use

• Aircraft stand cleaning and scrubbing with or without detergent

6

Hopper Specification

Hopper void 14m³

Hopper water tank standard 3600 Litres

Hopper water tank optional 1000 – 4000 Litres

Hopper waste volume 6000 litres

Material 304 stainless steel

Tip angle 37 degrees

Rear door opening angle 115 degrees

1122365 UHP170 - UHP250 Brochure GB.indd 7 24/09/12 07.42

1122365-UHP-Brochure-GB_210x297mm.pdf - 07:45:20 - September 24, 2012 - Page 6 of 8 - Coated preflight

Page 7: Beam UHP170 & UHP250 Ultra High Pressure Washer€¦ · Beam UHP170 & UHP250 Ultra High Pressure Washer Runway Rubber Removal - Painted Line Removal - Surface Texturing 1122365 UHP170

Hydrostatic gearboxThe hydrostatic gearbox has a maximum continuous torque of 21000 Nm in mechanical

mode for normal driving. The gear ratios range from 5.27 to 36.24 giving a speed between 0

and 5Km/h in hydrostatic mode. The hydrostatic gearbox has a length of 720 mm, height of

850 mm and a weight of 430 kg.

In hydrostatic drive, the vehicle is controlled from the chassis throttle pedal – both

acceleration and braking. When a desired speed has been reached an autopilot/ cruise

control can be engaged. The autopilot forward and reverse buttons are controlled from a

panel situated at the driver’s armrest.

Cooling and FiltrationAll Beam heavy duty cleaning machines are designed to work in a wide range of arduous

environments. The UHP machines have engine, hydraulic and water systems rated to

operate at up to 50 ºC ambient air temperature. The water filtration system ensures that all

impurities greater than 1μm Are filtered out and cannot damage the precision elements of

the water pump and nozzles.

7

1122365 UHP170 - UHP250 Brochure GB.indd 8 24/09/12 07.42

1122365-UHP-Brochure-GB_210x297mm.pdf - 07:45:21 - September 24, 2012 - Page 7 of 8 - Coated preflight

Page 8: Beam UHP170 & UHP250 Ultra High Pressure Washer€¦ · Beam UHP170 & UHP250 Ultra High Pressure Washer Runway Rubber Removal - Painted Line Removal - Surface Texturing 1122365 UHP170

Beam A/SSalten Skovvej 4-6 DK- 8653 Them Denmark

Tel.: +45 8684 7600 Fax: +45 8684 7734

www.beamsweepers.com

Due to continuous product development Beam A/S reserves

the right to alter specifications without prior notice.

AIRBRO/ENG/SIL/4K/05 2009

UHP170 UHP250

Water pressure 2500 bar 2250 bar

Water flow 34 litres 57 litres

Cleaning width rear 1500 mm (66 nozzles) 2500 mm (110 nozzles)

Vehicle speed hydrostatic motion 5 km/h 5 km/h

Covered area 300-1200 m2/h 500-2000 m2/h

Hopper material 304 stainless steel 304 stainless steel

Water tank material 304 stainless steel 304 stainless steel

Fan system capacity 30.000m3/h @ 1.800 mm water column 30.000m3/h @ 1.800 mm water column

Hopper size 14m3 (waste volume 6000 liter) 14m3 (waste volume 6000 liter)

Water volume std 3600 litres 3600 litres

Waste capacity 6000 litres 6000 litres

Tipping angle 37 degrees 37 degrees

Rear door opening angle 115 degrees 115 degrees

Optional Equipment – available to both machines

Front or side mounted rotorcleaning heads for smaller area cleaning – eg painted lines 300mm/ 350mm/ 500mm

Water tanks – external 1000, 1100,1500, 2000 and 4000 litres

Water tanks – internal (note – decrease waste capacity proportionally) 1000, 2000 litres

Sweeping systems located between axles for sweeping scrubbing and cleaning 2400mm up to 3600mm swept width

Detergent systems 200 – 600 litres

1122365 UHP170 - UHP250 Brochure GB.indd 1 24/09/12 07.41

1122365-UHP-Brochure-GB_210x297mm.pdf - 07:45:23 - September 24, 2012 - Page 8 of 8 - Coated preflight