Bazzar Road Control Room Building Design
-
Upload
anonymous-nwbyj9l -
Category
Documents
-
view
216 -
download
0
Transcript of Bazzar Road Control Room Building Design
![Page 1: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/1.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 1/39
1.0 INTRODUCTION:
This report is for structural design of Construction of RCC Framed structure for 33/11
KV indoor Substation Control room building super structure including foundation
design at Bazzar Road near Saidapet for T!"#$C%&
'&( STR)CT)R#S*
'&1 +ocation*
The Structure is located opposite to Saidapet bus stand facing front side entrance as
nna Salai Road and Bazzar Road on other side ,ith s-e, size plot at Chennai&
'&' "eneral $escription *
This Building consists of "round and First floor housing .V Transformer in "round
floor ,ith Batter0 room and 33/11 KV anel brea-ers in first floor& The linth height is
(&2(m aboe the Road leel on nna salai Road& The height of "round Floor is 4&(m
from bottom of "round floor beam& The first floor height is 5&(m from top of "F roof
slab to bottom of main beam& !ecessar0 cable duct proision for Transformer around
Transformer plinth has been proided for entr0 and e6it of cables& lso opening for
entr0 of cables to brea-ers and opening of ta-ing panels ,ith chec-er plate is
considered in First floor slab as per la0out& roision for staircase for landing First
floor and roof is proided ad7acent to control room&
'&3 Soil $ata*
Soil 8nestigation ,as conducted b0 $S aterial Testing t +td&9 !o&'.9 Velacher0Road9 Saidapet9 Chennai:15& The0 hae conducted 1 !o& Bore hole up to a depth of
15&(m& The top soil up to 1&5m is filled up soil follo,ed b0 Sand0 soil up to a depth of
1(&5m& Belo, 1(&5m9 the soil consists of Silt0 sand ,ith cla0 up to the depth of 15&(m&
;ater Table is found at a depth of 2&'m& For the proposed structure of "round and
First floor of 33/11 KV 8ndoor Sub Station9 the soil Consultant hae recommended to
proide 8solated Footing ,ith Safe Bearing capacit0 of soil as 14t/m' at a depth of
3&(m& The corresponding ! alue at 3&(m depth is 1<& ;ithin the foundation there is no
aderse or s,elling characteristics and hence no special t0pe of foundation is re=uired&
'&< foundation S0stem*
![Page 2: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/2.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 2/39
WIND LOAD
( IS875--Part 3--1987)Wind forces acting on a given surface is equal to the ind !ressures"ulti!lied #$ the effected area%
1% &esign ind s!eed (') &esign ind s!eed is given #$ the equation
'* '# +1 +, +3 here' *&esign ind s!eed'#* asic ind s!eed (a!!endi. / of 0+1*is2 0oefficient (a#le 1 of IS875-!art3)+,*errain4 height and structure sie factor (a#le , of IS875-!art3)
+3 * o!ogra!h$ factor (0lause 5%3%3%1 of IS875-!art3)1% asic Wind S!eed ('#)asic ind s!eed '#4 de!onds on the location of the #uilding% or this!ur!ose4 the countr$ is divided in to si. ones ith s!ecified ind s!eeds
![Page 3: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/3.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 3/39
ranging fro" 33"6s to 55 "6s% asic ind s!eed is #ased on gust velocit$averaged over a short ti"e interval of 3 seconds at 1" height fro" "eanground level in an o!en terrain and for 5 $ears return !eriod% /!!endi. /(ig%1) of the code s!ecified for so"e i"!ortant cities6 tons is given%,% is2 coefficient (+1 factor) he ris2 coefficient ta2es in to account the degree of relia#ilit$ requiredand the e.!ected lifr of structure4 sa$ 5 $ears for te"!orar$ sheds4 ,5
$ears for structures of "inor i"!ortance and 1 $ears for i"!ortant#uildings% a#le 1 of IS 875- !art 3-1987 for +1 factor are given%3%errain4 height and structure sie factor (+, factor)
STEP 1 (Creation of Geometry):
e Proect Select Plane :ength *"eters; orce*+;
ile a"e*Plane 1 e.t
Select <!en Structure Wiard inish%
0hange to ra"e =odels fro" russ "odels Select 0ontinuous #ea" and
dou#le clic2 on it%
:ength*>%" 0lic2
o% of #a$s (S!an) *1
/!!l$ ransfer "odel 0lic2 $es <+ ?o to ront vie icon (first
vie)
STPE 2 (Member Properties):
Select the "e"#er ro" =ain "enu 0o""ands =e"#er Pro!ert$
Pris"atic ectangular @&*%> A&*%,3 /ssign 0lose%
&e select the "e"#er%
![Page 4: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/4.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 4/39
STEP 3 (Supports):
0hange to ode cursor (oint) and select the nodes (oints)%
(If "ore than one node use 0: 2e$ and select the nodes) ro" =ain
"enu 0o""ands Su!!ort s!ecification Pinned /ssign 0lose
&e select the nodes and change to #ea" cursor%
STEP 4 (Loadin ):
ro" =ain "enu 0o""ands :oading Pri"ar$ :oad :oad case 1
/dd 0lose Select :oad case 1 /dd =e"#er :oad
0oncentrated orce P1*,+ ; d1*1%5 ; d,* /dd
P,*>% +; d1*3%; d,* /dd 0lose
Select the :oad P1*,+ and its "e"#er B /ssign to selected #ea"
/ssign <+%
Select the :oad P,*>%+ and its "e"#er assign to selected #ea"
/ssign <+ 0lose%
STEP !( "na#ysis ):
ro" =ain "enu 0o""ands B /nal$sis Perfor" /nal$sis o !rint
<+%
STEP $ (Post "na#ysis Print):
ro" =ain =enu 0o""ands Post /nal$sis Print Su!!ort eactions
o vie <+%
STEP %( &esin) :
![Page 5: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/5.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 5/39
ro" =ain "enu 0o""ands &esign 0oncrete &esign 0urrent
code*IS >5C ro" =ain "enu ools Set current in!ut unit
:ength *""; orce * <+%
Select the "e"#er &efine !ara"eters
D:@ *%85 /ssign
D:A *%85 /ssign
0 *, /ssign
@=/I* >15 /ssign
@SD0 *>15 /ssign
=/E=/I *1C /ssign
=/ESD0 *8 /ssign
=I=/I *1, /ssign
=ISD0 *8 B /ssign 0lose%
&e select all "e"#ers and select #ea" "e"#er onl$ 0o""ands
(0oncrete &esign) &esign #ea" /ssign 0lose a2e off /ssign
0lose%
ote Save the ile and un the Progra"%
SDP 8 (/nal$sis)
ro" =ain =enu F /nal$sis un /nal$sis un /nal$sis &one%
Select the "e"#er and dou#le clic2 on it Shear #ending 0lose%
S'ETC
![Page 6: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/6.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 6/39
P*+LEM ,*-2:
STEP 1 (Creation of Geometry):
e Proect Select Plane :ength *"eters; orce*+g;
ile a"e*Plane , e.t
Select <!en Structure Wiard inish%
0hange to ra"e =odels fro" russ "odels Select 0ontinuous #ea" and
dou#le clic2 on it%
:ength*C" 0lic2
o% of #a$s (S!an) *1
/!!l$ ransfer "odel 0lic2 @es <+ ?o to ront vie icon (first
vie)
STPE 2 (Member Properties):
Select the "e"#er ro" =ain "enu 0o""ands =e"#er Pro!ert$
Pris"atic ectangular @&*%> A&*%,3 /ssign 0lose%
&e select the "e"#er%
![Page 7: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/7.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 7/39
STEP 3 (Supports):
0hange to ode cursor (oint) and select the nodes (oints)%
(If "ore than one node use 0: 2e$ and select the nodes) ro" =ain
"enu 0o""ands Su!!ort s!ecification Pinned /ssign 0lose
&e select the nodes and change to #ea" cursor%
STEP 4 (Loadin ):
ro" =ain "enu 0o""ands :oading Pri"ar$ :oad :oad case 1
/dd 0lose Select :oad case 1 /dd =e"#er :oad Gnifor"
orce *, ; d1*3% ; d,* /dd 0lose%
Select the :oad and its "e"#er /ssign to selected #ea" /ssign
<+%
0lose%
STEP !( "na#ysis ):
ro" =ain "enu 0o""and B /nal$sis Perfor" /nal$sis o !rint B
<+%
STEP $ (Post "na#ysis Print):
ro" =ain =enu 0o""ands Post /nal$sis Print Su!!ort eactions
o vie <+%
STEP %( &esin) :
ro" =ain "enu 0o""ands &esign 0oncrete &esign 0urrent
code*IS >5C ro" =ain "enu ools Set current in!ut unit%
:ength *""; orce * <+%
![Page 8: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/8.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 8/39
Select the "e"#ers &efine !ara"eters
D:@ *%85 /ssign
D:A *%85 /ssign
0 *, /ssign
@=/I* >15 /ssign
@SD0 *>15 /ssign
=/E=/I *1C /ssign
=/ESD0 *8 /ssign
=I=/I *1, /ssign
=ISD0 *8 B /ssign 0lose
&e select all "e"#ers and select #ea"s onl$ 0o""ands (0oncrete
&esign) &esign #ea" /ssign 0lose a2e off /ssign 0lose%
ote Save the ile and un the Progra"%
SDP 8 (/nal$sis)
ro" =ain =enu F /nal$sis un /nal$sis un /nal$sis &one%
Select the "e"#er and dou#le clic2 on it Shear #ending 0lose%
S'ETC
P<:D= <%3%S+D0H
![Page 9: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/9.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 9/39
STEP 1 (Creation of Geometry):
e Proect Select Plane :ength *"eters; orce*+;
ile a"e*Plane 3 e.t
Select <!en Structure Wiard inish%
0hange to ra"e =odels fro" russ "odels Select 0ontinuous #ea" and
dou#le clic2 on it%
:ength*C" 0lic2
o% of #a$s (S!an) *1
/!!l$ ransfer "odel 0lic2 $es <+ ?o to ront vie icon (first
vie)
STPE 2 (Member Properties):
Select the "e"#er ro" =ain "enu 0o""ands =e"#er Pro!ert$
Pris"atic ectangular @&*%> A&*%,3 /ssign 0lose%
&e select the "e"#er%
STEP 3 (Supports):
0hange to ode cursor (oint) and select the nodes (oints)%
![Page 10: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/10.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 10/39
(If "ore than one node use 0: 2e$ and select the nodes) ro" =ain
"enu 0o""ands Su!!ort s!ecification Pinned /ssign 0lose
&e select the nodes and change to #ea" cursor%
STEP 4 (Loadin ):
ro" =ain "enu 0o""ands :oading Pri"ar$ :oad :oad case 1
/dd 0lose Select :oad case 1 /dd =e"#er :oad
0oncentrated orce P1*,+ ; d1*1%5 ; d,* /dd
P,*5 +; d1*>%5 ; d,* /dd
Select the :oad P1*,+ and its "e"#er /ssign to selected #ea"
/ssign <+% Select the load P,*5+ and its "e"#er /ssign to selected
#ea" /ssign<+%
Select the :oad case 1 /dd =e"#er :oad Gnifor" orce
*,+6"; d1*; d,*1%5 /dd
*,+6" ; d1* 3; d,* /dd
Select the unifor" load and its "e"#er assign to selected #ea"
/ssign <+ 0lose%
STEP !( "na#ysis ):
ro" =ain "enu 0o""ands /nal$sis Perfor" /nal$sis
o !rint <+%
STEP $ (Post "na#ysis Print):
ro" =ain =enu 0o""ands Post /nal$sis Print Su!!ort eactions
o vie <+%
![Page 11: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/11.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 11/39
STEP %( &esin) :
ro" =ain "enu 0o""ands &esign 0oncrete &esign 0urrent
code*IS >5C ro" =ain "enu ools Set current in!ut unit
:ength *""; orce * <+%
Select the "e"#er &efine !ara"eters
D:@ *%85 /ssign
D:A *%85 /ssign
0 *, /ssign
@=/I* >15 /ssign
@SD0 *>15 /ssign
=/E=/I *1C /ssign
=/ESD0 *8 /ssign
=I=/I *1, /ssign
=ISD0 *8 B /ssign 0lose%
&e select all "e"#ers and select #ea" onl$ 0o""ands (0oncrete
&esign) &esign #ea" /ssign 0lose a2e off /ssign 0lose%
ote Save the ile and un the Progra"%
SDP 8 (/nal$sis)
ro" =ain =enu F /nal$sis un /nal$sis un /nal$sis &one%
Select the "e"#er and dou#le clic2 on it Shear #ending 0lose%
S'ETC
![Page 12: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/12.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 12/39
P<:D= <%>
STEP 1 (Creation of Geometry):
e Proect Select Plane :ength *"eters; orce*+;
ile a"e*Plane > e.t
![Page 13: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/13.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 13/39
Select <!en Structure Wiard inish%
0hange to ra"e =odels fro" russ "odels Select 0ontinuous #ea"
and dou#le clic2 on it%
:ength*C" 0lic2
o% of #a$s (S!an) *1
/!!l$ ransfer "odel 0lic2 $es <+ ?o to ront vie icon (first
vie)
STPE 2 (Member Properties):
Select the "e"#er
ro" =ain "enu
0o""ands
=e"#er Pro!ert$
Pris"atic ectangular @&*%5 A&*%,3 /ssign 0lose%
&e select the "e"#er%
STEP 3 (Supports):
0hange to ode cursor (oint) and select the nodes (oints)%
(If "ore than one node use 0: 2e$ and select the nodes) ro" =ain
"enu 0o""ands Su!!ort s!ecification Pinned /ssign 0lose
&e select the nodes and change to #ea" cursor%
STEP 4 (Loadin ):
ro" =ain "enu 0o""ands :oading Pri"ar$ :oad :oad case 1
/dd close Select :oad case 1 /dd =e"#er :oad Gnifor"
orce G&:*15+g ; d1* ; d,* /dd =e"#er load
0oncentrated forces P1*1 +g; d1*1%5; d,* /dd =e"#er
load 0oncentrated force P,*, +g; d1*3% ; d,* /dd
=e"#er load 0oncentrated forces P3*3 +g; d1*>%5; d,* /dd
![Page 14: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/14.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 14/39
0lose Select the G&: P1 *15 +g and select the "e"#er
/ssign to selected #ea" /ssign Select the :oad P,*,2g and
select the "e"#er /ssign selected "e"#er(#ea") /ssign Select
the :oad P3*32g and select the "e"#er /ssign <+ 0lose%
STEP ! ( "na#ysis ):
ro" =ain "enu 0o""and /nal$sis Perfor" /nal$sis o !rint
B<+%
STEP $ (Post "na#ysis Print):
ro" =ain =enu 0o""ands Post /nal$sis Print Su!!ort eactions
o vie <+%
STEP % ( &esin) :
ro" =ain "enu 0o""ands &esign 0oncrete &esign 0urrent
code*IS >5C ro" =ain "enu ools Set current in!ut unit
:ength *""; orce * <+%
Select the "e"#er &efine !ara"eters
D:@ *%85 /ssign
D:A *%85 /ssign
0 *, /ssign
@=/I* >15 /ssign
@SD0 *>15 /ssign
=/E=/I *1C /ssign
=/ESD0 *8 /ssign
![Page 15: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/15.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 15/39
=I=/I *1, /ssign
=ISD0 *8 B /ssign 0lose%
&e select all "e"#ers and select #ea" onl$ 0o""ands (0oncrete
&esign) &esign #ea" /ssign 0lose a2e off /ssign 0lose%
ote Save the ile and un the Progra"%
SDP 8 (/nal$sis)
ro" =ain =enu F /nal$sis un /nal$sis un /nal$sis &one%
Select the "e"#er and dou#le clic2 on it Shear #ending 0lose%
S'ETC
SI=P:D D/= WIH I/?G:/ :</&
P<:D= <%5
S+D0H
![Page 16: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/16.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 16/39
STEP 1 (Creation of Geometry):
e Proect Select Plane :ength *"eters; orce*+;
ile a"e*Plane 3 e.t
Select <!en Structure Wiard inish%
0hange to ra"e =odels to russ "odels Select 0ontinuous #ea" and
dou#le clic2 on it%
:ength*C" 0lic2
o% of #a$s (S!an) *1
/!!l$ ransfer "odel 0lic2 $es <+ ?o to ront vie icon (first
vie)
STPE 2 (Member Properties):
Select the "e"#er ro" =ain "enu 0o""ands =e"#er Pro!ert$
Pris"atic ectangular @&*%> A&*%,3 /ssign 0lose%
&e select the "e"#er%
STEP 3 (Supports):
![Page 17: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/17.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 17/39
0hange to ode cursor (oint) and select the nodes (oints)%
(If "ore than one node use 0: 2e$ and select the nodes) ro" =ain
"enu 0o""ands Su!!ort s!ecification Pinned /ssign 0lose
&e select the nodes and change to #ea" cursor%
STEP 4 (Loadin ):
ro" =ain "enu 0o""ands :oading Pri"ar$ :oad :oad case 1
/dd close Select :oad case 1 /dd =e"#er :oad
0oncentrated orce P1*,+ ; d1*1%5 ; d,* /dd
P,*5 +; d1*>%5 ; d,* /dd
Select the :oad and its "e"#er B /ssign to selected #ea" /ssign <+%
Select the :oad case 1 /dd =e"#er :oad Gnifor" orce
*,+6"; d1*; d,*1%5 /dd% *,+6" ; d1* 3; d,* /dd
Select the unifor" load and its "e"#er assign to selected #ea"
/ssign <+ 0lose%
STEP !( "na#ysis ):
ro" =ain "enu 0o""and B /nal$sis Perfor" /nal$sis o !rint B
<+%
STEP $ (Post "na#ysis Print):
ro" =ain =enu 0o""ands Post /nal$sis Print Su!!ort eactions
o vie <+%
STEP %( &esin) :
![Page 18: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/18.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 18/39
ro" =ain "enu 0o""ands &esign 0oncrete &esign 0urrent
code*IS >5C ro" =ain "enu ools Set current in!ut :ength
*""; orce * <+%
Select all the "e"#ers &esign !ara"eters
D:@ *%85 /ssign
D:A *%85 /ssign
0 *, /ssign
@=/I* >15 /ssign
@SD0 *>15 /ssign
=/E=/I *1C /ssign
=/ESD0 *8 /ssign
=I=/I *1, /ssign
=ISD0 *8 B /ssign 0lose%
&e select all "e"#ers and select #ea"s onl$ 0o""ands (0oncrete
&esign) &esign #ea" /ssign 0lose a2e off /ssign 0lose%
ote Save the ile and un the Progra"%
SDP 8 (/nal$sis)
ro" =ain =enu F /nal$sis un /nal$sis un /nal$sis &one%
Select the "e"#er and dou#le clic2 on it Shear #ending 0lose%
S'ETC
![Page 19: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/19.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 19/39
![Page 20: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/20.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 20/39
&e select the "e"#er%
STEP 3 (Supports):
0hange to ode cursor (oint) and select the nodes (oints)%
(If "ore than one node use 0: 2e$ and select the nodes) ro" =ain
"enu 0o""ands Su!!ort s!ecification Pinned /ssign 0lose
&e select the nodes and change to #ea" cursor%
STEP 4 (Loadin ):
ro" =ain "enu 0o""ands :oading Pri"ar$ :oad :oad case 1
/dd close Select :oad case 1 /dd =e"#er :oad
ra!eoidal 1*1C; d1* ; d,* /dd
W,*8 ; d1* ; d,*5% /dd
Select the ra!eoidal :oad and its "e"#er B /ssign to selected #ea"
/ssign <+ 0lose%
STEP !( "na#ysis ):
ro" =ain "enu 0o""and /nal$sis Perfor" /nal$sis o !rint
<+%
STEP $ (Post "na#ysis Print):
ro" =ain =enu 0o""ands Post /nal$sis Print Su!!ort eactions
o vie <+%
STEP %( &esin) :
ro" =ain "enu 0o""ands &esign 0oncrete &esign 0urrent
code*IS >5C ro" =ain "enu ools Set current in!ut unit
:ength *""; orce * <+%
![Page 21: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/21.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 21/39
Select the "e"#er &efine !ara"eters
D:@ *%85 /ssign
D:A *%85 /ssign
0 *, /ssign
@=/I* >15 /ssign
@SD0 *>15 /ssign
=/E=/I *1C /ssign
=/ESD0 *8 /ssign
=I=/I *1, /ssign
=ISD0 *8 B /ssign 0lose%
&e select the "e"#er and select #ea" onl$ 0o""ands (0oncrete
&esign) &esign #ea" /ssign 0lose a2e off /ssign 0lose%
ote Save the ile and un the Progra"%
SDP 8 (/nal$sis)
ro" =ain =enu F /nal$sis un /nal$sis un /nal$sis &one%
Select the "e"#er and dou#le clic2 on it Shear #ending 0lose%
S'ETC
SI=P:D D/= WIH =<=DS GI<= :</&S
![Page 22: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/22.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 22/39
STEP 1 (Creation of Geometry):
e Proect Select Plane :ength *"eters; orce*+g;
ile a"e*Plane C e.t
Select <!en Structure Wiard inish%
0hange to ra"e =odels fro" russ "odels Select 0ontinuous #ea" and
dou#le clic2 on it%
:ength*8" 0lic2
o% of #a$s (S!an) *1
/!!l$ ransfer "odel clic2 $es o2 ?o to ront vie icon (first
vie)
STPE 2 (Member Properties):
Select the "e"#er ro" =ain "enu 0o""ands =e"#er Pro!ert$
Pris"atic ectangular @&*%8 A&*%> /ssign 0lose%
&e select the "e"#er%
STEP 3 (Supports):
0hange to ode cursor (oint) and select the nodes (oints)%
(If "ore than one node use 0: 2e$ and select the nodes) ro" =ain
"enu 0o""ands Su!!ort s!ecification Pinned /ssign 0lose
&e select the nodes and change to #ea" cursor%
STEP 4 (Loadin ):
![Page 23: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/23.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 23/39
ro" =ain "enu 0o""ands :oading Pri"ar$ :oad :oad case 1
/dd close Select :oad case 1 /dd Joint :oad =o"ent
=A*3, d1*C;d,* /dd =e"#er :oad :inear var$ing load
@* d1* ; d,* /dd
Select the :oad and its "e"#er B /ssign to selected #ea" /ssign <+%
Select the :oad case 1 /dd =e"#er :oad Gnifor" orce
*,+6"; d1*; d,*1%5 /dd% *,+6" ; d1* 3; d,* /dd
Select the unifor" load and its "e"#er assign to selected #ea"
/ssign <+ 0lose%
STEP !( "na#ysis ):
ro" =ain "enu 0o""and B /nal$sis Perfor" /nal$sis o !rint B
<+%
STEP $ (Post "na#ysis Print):
ro" =ain =enu 0o""ands Post /nal$sis Print Su!!ort eactions
o vie <+%
STEP %( &esin) :
ro" =ain "enu 0o""ands &esign 0oncrete &esign 0urrent
code*IS >5C ro" =ain "enu ools Set current in!ut :ength
*""; orce * <+%
Select all the "e"#ers &esign !ara"eters
D:@ *%85 /ssign
![Page 24: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/24.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 24/39
D:A *%85 /ssign
0 *, /ssign
@=/I* >15 /ssign
@SD0 *>15 /ssign
=/E=/I *1C /ssign
=/ESD0 *8 /ssign
=I=/I *1, /ssign
=ISD0 *8 B /ssign 0lose%
&e select all "e"#ers and select #ea"s onl$ 0o""ands (0oncrete
&esign) &esign #ea" /ssign 0lose a2e off /ssign 0lose%
ote Save the ile and un the Progra"%
SDP 8 (/nal$sis)
ro" =ain =enu F /nal$sis un /nal$sis un /nal$sis &one%
Select the "e"#er and dou#le clic2 on it Shear #ending 0lose%
S'ETC
STEP 1 (Creation of Geometry):
e Proect Select Plane :ength *"eters; orce*+;
![Page 25: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/25.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 25/39
ile a"e*Plane 3 e.t
Select <!en Structure Wiard inish%
0hange to ra"e =odels to russ "odels Select 0ontinuous #ea" and
dou#le clic2 on it%
:ength*C" 0lic2
o% of #a$s (S!an) *1
/!!l$ ransfer "odel clic2 $es o2 ?o to ront vie icon (first
vie)
STPE 2 (Member Properties):
Select the "e"#er ro" =ain "enu 0o""ands =e"#er Pro!ert$
Pris"atic ectangular @&*%> A&*%,3 /ssign 0lose%
&e select the "e"#er%
STEP 3 (Supports):
0hange to ode cursor (oint) and select the nodes (oints)%
(If "ore than one node use 0: 2e$ and select the nodes) ro" =ain
"enu 0o""ands Su!!ort s!ecification Pinned /ssign 0lose
&e select the nodes and change to #ea" cursor%
STEP 4 (Loadin ):
![Page 26: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/26.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 26/39
ro" =ain "enu 0o""ands :oading Pri"ar$ :oad :oad case 1
/dd close Select :oad case 1 /dd =e"#er :oad
0oncentrated orce P1*,+ ; d1*1%5 ; d,* /dd
P,*5 +; d1*>%5 ; d,* /dd
Select the :oad and its "e"#er B /ssign to selected #ea" /ssign <+%
Select the :oad case 1 /dd =e"#er :oad Gnifor" orce
*,+6"; d1*; d,*1%5 /dd% *,+6" ; d1* 3; d,* /dd
Select the unifor" load and its "e"#er assign to selected #ea"
/ssign <+ 0lose%
STEP !( "na#ysis ):
ro" =ain "enu 0o""and B /nal$sis Perfor" /nal$sis o !rint B
<+%
STEP $ (Post "na#ysis Print):
ro" =ain =enu 0o""ands Post /nal$sis Print Su!!ort eactions
o vie <+%
STEP %( &esin) :
ro" =ain "enu 0o""ands &esign 0oncrete &esign 0urrent
code*IS >5C ro" =ain "enu ools Set current in!ut :ength
*""; orce * <+%
Select all the "e"#ers &esign !ara"eters
D:@ *%85 /ssign
![Page 27: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/27.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 27/39
D:A *%85 /ssign
0 *, /ssign
@=/I* >15 /ssign
@SD0 *>15 /ssign
=/E=/I *1C /ssign
=/ESD0 *8 /ssign
=I=/I *1, /ssign
=ISD0 *8 B /ssign 0lose%
&e select all "e"#ers and select #ea"s onl$ 0o""ands (0oncrete
&esign) &esign #ea" /ssign 0lose a2e off /ssign 0lose%
ote Save the ile and un the Progra"%
SDP 8 (/nal$sis)
ro" =ain =enu F /nal$sis un /nal$sis un /nal$sis &one%
Select the "e"#er and dou#le clic2 on it Shear #ending 0lose%
S'ETC
STEP 1 (Creation of Geometry):
e Proect Select Plane :ength *"eters; orce*+;
![Page 28: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/28.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 28/39
ile a"e*Plane 3 e.t
Select <!en Structure Wiard inish%
0hange to ra"e =odels to russ "odels Select 0ontinuous #ea" and
dou#le clic2 on it%
:ength*C" 0lic2
o% of #a$s (S!an) *1
/!!l$ ransfer "odel clic2 $es o2 ?o to ront vie icon (first
vie)
STPE 2 (Member Properties):
Select the "e"#er ro" =ain "enu 0o""ands =e"#er Pro!ert$
Pris"atic ectangular @&*%> A&*%,3 /ssign 0lose%
&e select the "e"#er%
STEP 3 (Supports):
0hange to ode cursor (oint) and select the nodes (oints)%
(If "ore than one node use 0: 2e$ and select the nodes) ro" =ain
"enu 0o""ands Su!!ort s!ecification Pinned /ssign 0lose
&e select the nodes and change to #ea" cursor%
STEP 4 (Loadin ):
![Page 29: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/29.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 29/39
ro" =ain "enu 0o""ands :oading Pri"ar$ :oad :oad case 1
/dd close Select :oad case 1 /dd =e"#er :oad
0oncentrated orce P1*,+ ; d1*1%5 ; d,* /dd
P,*5 +; d1*>%5 ; d,* /dd
Select the :oad and its "e"#er B /ssign to selected #ea" /ssign <+%
Select the :oad case 1 /dd =e"#er :oad Gnifor" orce
*,+6"; d1*; d,*1%5 /dd% *,+6" ; d1* 3; d,* /dd
Select the unifor" load and its "e"#er assign to selected #ea"
/ssign <+ 0lose%
STEP !( "na#ysis ):
ro" =ain "enu 0o""and B /nal$sis Perfor" /nal$sis o !rint B
<+%
STEP $ (Post "na#ysis Print):
ro" =ain =enu 0o""ands Post /nal$sis Print Su!!ort eactions
o vie <+%
STEP %( &esin) :
ro" =ain "enu 0o""ands &esign 0oncrete &esign 0urrent
code*IS >5C ro" =ain "enu ools Set current in!ut :ength
*""; orce * <+%
Select all the "e"#ers &esign !ara"eters
D:@ *%85 /ssign
![Page 30: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/30.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 30/39
D:A *%85 /ssign
0 *, /ssign
@=/I* >15 /ssign
@SD0 *>15 /ssign
=/E=/I *1C /ssign
=/ESD0 *8 /ssign
=I=/I *1, /ssign
=ISD0 *8 B /ssign 0lose%
&e select all "e"#ers and select #ea"s onl$ 0o""ands (0oncrete
&esign) &esign #ea" /ssign 0lose a2e off /ssign 0lose%
ote Save the ile and un the Progra"%
SDP 8 (/nal$sis)
ro" =ain =enu F /nal$sis un /nal$sis un /nal$sis &one%
Select the "e"#er and dou#le clic2 on it Shear #ending 0lose%
S'ETC
STEP 1 (Creation of Geometry):
e Proect Select Plane :ength *"eters; orce*+;
![Page 31: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/31.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 31/39
ile a"e*Plane 3 e.t
Select <!en Structure Wiard inish%
0hange to ra"e =odels to russ "odels Select 0ontinuous #ea" and
dou#le clic2 on it%
:ength*C" 0lic2
o% of #a$s (S!an) *1
/!!l$ ransfer "odel clic2 $es o2 ?o to ront vie icon (first
vie)
STPE 2 (Member Properties):
Select the "e"#er ro" =ain "enu 0o""ands =e"#er Pro!ert$
Pris"atic ectangular @&*%> A&*%,3 /ssign 0lose%
&e select the "e"#er%
STEP 3 (Supports):
0hange to ode cursor (oint) and select the nodes (oints)%
(If "ore than one node use 0: 2e$ and select the nodes) ro" =ain
"enu 0o""ands Su!!ort s!ecification Pinned /ssign 0lose
&e select the nodes and change to #ea" cursor%
STEP 4 (Loadin ):
![Page 32: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/32.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 32/39
ro" =ain "enu 0o""ands :oading Pri"ar$ :oad :oad case 1
/dd close Select :oad case 1 /dd =e"#er :oad
0oncentrated orce P1*,+ ; d1*1%5 ; d,* /dd
P,*5 +; d1*>%5 ; d,* /dd
Select the :oad and its "e"#er B /ssign to selected #ea" /ssign <+%
Select the :oad case 1 /dd =e"#er :oad Gnifor" orce
*,+6"; d1*; d,*1%5 /dd% *,+6" ; d1* 3; d,* /dd
Select the unifor" load and its "e"#er assign to selected #ea"
/ssign <+ 0lose%
STEP !( "na#ysis ):
ro" =ain "enu 0o""and B /nal$sis Perfor" /nal$sis o !rint B
<+%
STEP $ (Post "na#ysis Print):
ro" =ain =enu 0o""ands Post /nal$sis Print Su!!ort eactions
o vie <+%
STEP %( &esin) :
ro" =ain "enu 0o""ands &esign 0oncrete &esign 0urrent
code*IS >5C ro" =ain "enu ools Set current in!ut :ength
*""; orce * <+%
Select all the "e"#ers &esign !ara"eters
D:@ *%85 /ssign
![Page 33: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/33.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 33/39
![Page 34: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/34.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 34/39
STEP 1 (Creation of Geometry):
e Proect Select Plane :ength *"eters; orce*+;
ile a"e*Plane 3 e.t
Select <!en Structure Wiard inish%
0hange to ra"e =odels to russ "odels Select 0ontinuous #ea" and
dou#le clic2 on it%
:ength*C" 0lic2
o% of #a$s (S!an) *1
/!!l$ ransfer "odel clic2 $es o2 ?o to ront vie icon (first
vie)
STPE 2 (Member Properties):
Select the "e"#er ro" =ain "enu 0o""ands =e"#er Pro!ert$
Pris"atic ectangular @&*%> A&*%,3 /ssign 0lose%
&e select the "e"#er%
STEP 3 (Supports):
0hange to ode cursor (oint) and select the nodes (oints)%
(If "ore than one node use 0: 2e$ and select the nodes) ro" =ain
"enu 0o""ands Su!!ort s!ecification Pinned /ssign 0lose
&e select the nodes and change to #ea" cursor%
STEP 4 (Loadin ):
![Page 35: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/35.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 35/39
ro" =ain "enu 0o""ands :oading Pri"ar$ :oad :oad case 1
/dd close Select :oad case 1 /dd =e"#er :oad
0oncentrated orce P1*,+ ; d1*1%5 ; d,* /dd
P,*5 +; d1*>%5 ; d,* /dd
Select the :oad and its "e"#er B /ssign to selected #ea" /ssign <+%
Select the :oad case 1 /dd =e"#er :oad Gnifor" orce
*,+6"; d1*; d,*1%5 /dd% *,+6" ; d1* 3; d,* /dd
Select the unifor" load and its "e"#er assign to selected #ea"
/ssign <+ 0lose%
STEP !( "na#ysis ):
ro" =ain "enu 0o""and B /nal$sis Perfor" /nal$sis o !rint B
<+%
STEP $ (Post "na#ysis Print):
ro" =ain =enu 0o""ands Post /nal$sis Print Su!!ort eactions
o vie <+%
STEP %( &esin) :
ro" =ain "enu 0o""ands &esign 0oncrete &esign 0urrent
code*IS >5C ro" =ain "enu ools Set current in!ut :ength
*""; orce * <+%
Select all the "e"#ers &esign !ara"eters
D:@ *%85 /ssign
![Page 36: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/36.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 36/39
D:A *%85 /ssign
0 *, /ssign
@=/I* >15 /ssign
@SD0 *>15 /ssign
=/E=/I *1C /ssign
=/ESD0 *8 /ssign
=I=/I *1, /ssign
=ISD0 *8 B /ssign 0lose%
&e select all "e"#ers and select #ea"s onl$ 0o""ands (0oncrete
&esign) &esign #ea" /ssign 0lose a2e off /ssign 0lose%
ote Save the ile and un the Progra"%
SDP 8 (/nal$sis)
ro" =ain =enu F /nal$sis un /nal$sis un /nal$sis &one%
Select the "e"#er and dou#le clic2 on it Shear #ending 0lose%
S'ETC
![Page 37: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/37.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 37/39
STEP 1 (Creation of Geometry):
e Proect Select Plane :ength *"eters; orce*+;
ile a"e*Plane 3 e.t
Select <!en Structure Wiard inish%
0hange to ra"e =odels to russ "odels Select 0ontinuous #ea" and
dou#le clic2 on it%
:ength*C" 0lic2
o% of #a$s (S!an) *1
/!!l$ ransfer "odel clic2 $es o2 ?o to ront vie icon (first
vie)
STPE 2 (Member Properties):
Select the "e"#er ro" =ain "enu 0o""ands =e"#er Pro!ert$
Pris"atic ectangular @&*%> A&*%,3 /ssign 0lose%
&e select the "e"#er%
STEP 3 (Supports):
0hange to ode cursor (oint) and select the nodes (oints)%
(If "ore than one node use 0: 2e$ and select the nodes) ro" =ain
"enu 0o""ands Su!!ort s!ecification Pinned /ssign 0lose
&e select the nodes and change to #ea" cursor%
![Page 38: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/38.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 38/39
STEP 4 (Loadin ):
ro" =ain "enu 0o""ands :oading Pri"ar$ :oad :oad case 1
/dd close Select :oad case 1 /dd =e"#er :oad
0oncentrated orce P1*,+ ; d1*1%5 ; d,* /dd
P,*5 +; d1*>%5 ; d,* /dd
Select the :oad and its "e"#er B /ssign to selected #ea" /ssign <+%
Select the :oad case 1 /dd =e"#er :oad Gnifor" orce
*,+6"; d1*; d,*1%5 /dd% *,+6" ; d1* 3; d,* /dd
Select the unifor" load and its "e"#er assign to selected #ea"
/ssign <+ 0lose%
STEP !( "na#ysis ):
ro" =ain "enu 0o""and B /nal$sis Perfor" /nal$sis o !rint B
<+%
STEP $ (Post "na#ysis Print):
ro" =ain =enu 0o""ands Post /nal$sis Print Su!!ort eactions
o vie <+%
STEP %( &esin) :
ro" =ain "enu 0o""ands &esign 0oncrete &esign 0urrent
code*IS >5C ro" =ain "enu ools Set current in!ut :ength
*""; orce * <+%
Select all the "e"#ers &esign !ara"eters
![Page 39: Bazzar Road Control Room Building Design](https://reader030.fdocuments.in/reader030/viewer/2022021322/577cd30c1a28ab9e78968fad/html5/thumbnails/39.jpg)
8/13/2019 Bazzar Road Control Room Building Design
http://slidepdf.com/reader/full/bazzar-road-control-room-building-design 39/39
D:@ *%85 /ssign
D:A *%85 /ssign
0 *, /ssign
@=/I* >15 /ssign
@SD0 *>15 /ssign
=/E=/I *1C /ssign
=/ESD0 *8 /ssign
=I=/I *1, /ssign
=ISD0 *8 B /ssign 0lose%
&e select all "e"#ers and select #ea"s onl$ 0o""ands (0oncrete
&esign) &esign #ea" /ssign 0lose a2e off /ssign 0lose%
ote Save the ile and un the Progra"%
SDP 8 (/nal$sis)
ro" =ain =enu F /nal$sis un /nal$sis un /nal$sis &one%
Select the "e"#er and dou#le clic2 on it Shear #ending 0lose%
S'ETC