BAL WP1 Tanking over Sealux Reg 20 - Waterproofing Showers · 2017. 3. 28. · a Sealux Reg 20...
Transcript of BAL WP1 Tanking over Sealux Reg 20 - Waterproofing Showers · 2017. 3. 28. · a Sealux Reg 20...
Installing the BAL Waterproofing Kit overa Sealux Reg 20 Joint Sealing Profile
25
Waterproofing Kit Materials
1) APD Priming Coat2) WP1 Waterproofing Coat3) Polyester Tape4) Polyester Matting
Min App. Temp. = 5°
Toolsrequired.
26
27
Mark out splash zone. Splash zone should extend 100mm outside shower area and upward to shoulder height.
Brush wall to remove loose particles.
Wall surfaces should be smooth. Flush fill
all recesses with filler.
28
29
30
Apply masking tape over strip and ledge surfaces.
Mask pipes and fitting protrusions.
Prepare the polyester reinforcing tape while the primer is drying (30 mins).
Primewalls
stroking brush in various
directions over all
surfaces.
31
32
33
34
Notch the polyester tape to form a leg that can extend
around corners and maintain a seal
between meeting strip up-stands.
In a 3 sided installation the middle length may have 2 legs, or each side length just 1 leg.
35
36
39
40
41
37
38
Laying the polyester tape against a wall for support, fold it into two halves pressing the
Substrate transition joints should also be reinforced with polyester tape.
Reinforce all pipes and fitting protrusions.
fold firmly to form a permanent crease
line that will ease the application process.
42
43
44
45
46
47
48
49
50
51
Paint WP1 onto the wall and strip up-stand for polyester base tapes.
Bed the first polyester basetape (keeping
leg folded) ontothe WP1 coating.
Unfold and bed the leg onto the adjacent wall.
Paint the leg with WP1.
Bed second base tape onto the WP1 coating.
52
53
54
55Paint a WP1 undercoat onto the corner walls for the polyester corner tape.
working in an upward direction, bed the polyester corner tape
onto WP1 coating maintaining the fold, and keeping the crease line tight against the wall corner.
Starting just above the strip
up-stand and
Use the brush to open fold and bed it onto the adjacent WP1 coated wall.
57
58
56
Apply a second coat of WP1 over the polyester tape brushing it firmly to ensure
the polyester tape is fully embedded between the first and second WP1
waterproof coatings.
60
59
62
61
All pipes, fitting protrusions, and transition joints should be reinforced with polyester tape or
matting in a similar manner. Once complete, the walls are ready for waterproofing with BAL WP1.
6563
64
66
Apply a first coat of WP1over all surfaces strokingthe brush in vertical direction. After the first coat has dried, apply a second coat of WP1 stroking thebrush in an oppositehorizontal direction.
Remove masking tape and clean the ledge.
6768
69 The waterproofing is now complete. After the second WP1
coat has dried tiling may commence using:
1. BAL supercover rapid flex2. BAL micromax wall & floor grout
Remember, these are just general guidelines reflecting typical site conditions.
If you have any queries please contact:
IRL Tel: (01) 880 9210Email: [email protected]: www.bal.ie
UK Tel: 0845 600 1 222Email: [email protected]
IRL Tel: (01) 2989 121UK Tel: 0870 876 0 121Email: [email protected]: www.sealux.com
© Sealux