BAGFLO ITT - Bombeos, Reparaciones y …€¢ Diseño de acoplamiento corto para ahorrar espacio y...
Transcript of BAGFLO ITT - Bombeos, Reparaciones y …€¢ Diseño de acoplamiento corto para ahorrar espacio y...
Goulds PumpsAg-FloCast Iron Bronze Fitted End-Suction Flanged Pumps, Bombas horizontales con brida en hierro fundido o hierro fundido y bronce
Ag./Irrigation,Agr/Irrigación
BAGFLO
ITT
Engineered for life
2
A Full Range of Product Features The Ag-Flo pumps from Goulds have been designed with technical benefits to meet the needs of users in a variety of water supply, recircu-lation, and cooling applications.
• Close coupled design for space saving and simplified maintenance.
• Offers a bearing frame mounted design for flexibility of installation and drive arrangements.
• SAE drive sizes 1 through 5 avail-able on most pump sizes.
• Back pull-out to reduce mainte-nance down time.
• Standard Type 21 mechanical seal for both reliability and avail-ability. Carbon/ceramic/BUNA standard, with other faces and elastomers available.
• Available in packed stuffing box design with TeflonTM impregnat-ed packing, split Teflon lantern ring, tapped flush connection and 2 piece investment cast interlocking gland, all standard.
• Available in all iron or bronze fitted construction for application versatility.
• Replaceable wearing components include stainless steel shaft sleeve and casing and hub wear rings to maintain peak efficiency.
• Enclosed impeller design, dynamic balancing and renewable wear rings reduce losses affecting performance and pump life.
• 125 Class ANSI flange suction/ discharge connections and casing rotation for piping connection versatility.
• NPT threaded connections are supplied on several of the smaller capacity sizes.
• Optional rigid carbon steel bedplate, sheet metal coupling guard and T. B. Woods spacer coupling for power frame models.
• Standard NEMA motor frame, JM shaft extension (mechanical seal) JP shaft extension (packed box), C face mounting, single phase or three phase, 3500 or 1750 RPM for 60 Hz, 2900 or 1450 RPM for 50 Hz. Open drip-proof and totally enclosed fan cooled.
• Optional explosion proof and high efficiency motors are available.
Una amplia gama de variadas característicasLas bombas Ag-Flo de Goulds han sido diseñadas con beneficios técnicos para satisfacer las necesidades de los usuarios en variadas aplicaciones de suministro y recirculación de agua y aplicaciones de refrigeración.
• Diseño de acoplamiento corto para ahorrar espacio y simplificar el mantenimiento.
• Cuentan con un diseño de montaje sobre bastidor que ofrece gran flexi-bilidad en los arreglos de instalación y accionamiento.
• Tamaños de accionamiento SAE del 1 al 5 disponibles en la mayoría de los tamaños de bombas.
• Desmontaje posterior que reduce el tiempo de inactividad por mante-nimiento.
• Sello mecánico estándar Tipo 21 que brinda confiabilidad y disponibili-dad. Estándar de carbono/cerámi-ca/BUNA, también se encuentran disponibles con otros frentes y elastómeros.
• Disponibles en diseño con caja prensaestopas con empaque de TeflonTM impregnado, aro de linterna de Teflon dividido, conexión de lavado con derivación y casquillo fundido de conexión de inversión de 2 piezas, todo estándar.
• Disponibles en hierro o con acce-sorios de bronce para una mayor versatilidad de aplicación.
• Los componentes de desgaste reemplazables incluyen los anillos de desgaste de la carcasa y del rodete y la camisa del eje, de acero inoxi-dable, para mantener una máxima eficiencia.
• El diseño de impulsor encerrado, el balanceo dinámico y los anillos de desgaste reemplazables reducen las pérdidas que afectan el desempeño y la vida útil de la bomba.
• Conexiones de succión y descarga con brida ANSI de Clase 125 y car-casa rotativa para mayor versatilidad de conexión.
• Varios de los tamaños de capaci-dad más pequeños cuentan con conexiones NPT.
• Placa de asiento rígida de acero al carbono, protector de acoplamiento de chapa metálica y acoplamiento espaciador T. B. Woods disponibles opcionales en los modelos de cuadro de fuerza.
• Bastidor de motor NEMA estándar, extensión de eje JM (sello mecá-nico), extensión de eje JP (caja prensaestopas), montaje en cara C, monofásico o trifásico, 3500 ó 1750 RPM para 60 Hz, 2900 ó 1450 para 50 Hz. Abierto a prueba de filtraciones y totalmente encerrado enfriado por ventilador.
• Se encuentran disponibles motores a prueba de explosiones de alta eficiencia.
Goulds Pumps is ISO 9001 Registered.
Goulds PumpsAg. / Irrigation
3
1 x 2-7 (3500)1 x 2-8 (3500)
11/2 x 2-6 (3500)11/2 x 2-8 (3500)
2 x 2-5 (3500)21/2 x 21/2-5 (3500)
21/2 x 3-7 (3500)3 x 3-5 (3500)3 x 4-7 (3500)4 x 4-5 (3500)5 x 5-6 (3500)
2 x 21/2-7 (1750)2 x 21/2-7 (3500)
350
300
250
200
150
100
50
0
105
15
0
30
45
60
75
90
0
0 225
1000900800700600500400300200100
200175150125100755025CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
METERSMETROS
FEETPIES
GPM
m3/hr
11/2 x 2-8
21/2 x 3-7
11/2 x 2-61 x 2-7
2 x 2-5 21/2 x 21/2-53 x 3-5
3 x 4-7
4 x 4-55 x 5-6
1 x 2-8
2 x 21/2-7
2 x 21/2-7
Performance Coverage, Campo de desempeño
500
300
200
100
0
140
20
0
40
60
80
0
0 1000
45003000150012501000750500250
75050030025020015010050CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
ÍNAM
ICA
TOTA
L)
METERSMETROS
FEETPIES
GPM
m3/hr
400
100
120
400
11/2 x 2-10 (3500)21/2 x 3-9 (3500)
21/2 x 3-10 (3500)3 x 4-8 (3500)
3 x 4-10 (3500)4 x 5-8 (3500)
4 x 6-10 (1750)4 x 6-13 (1750)4 x 6-16 (1750)6 x 8-13 (1750)
8 x 10-13 (1750)11/4 x 11/2 -81/2 (3500)
5 x 5-7 (1750)5 x 6-7 (3500)
6 x 8-91/2 (1750)
3 x 4-103500 RPM
4 x 6-101750 RPM
3 x 4-83500 RPM
21/2 x 3-103500 RPM
8 x 10-131750 RPM
6 x 8-131750 RPM
4 x 5-83500 RPM
4 x 6-131750 RPM
4 x 6-161750 RPM
11/2 x 2-103500 RPM
21/2 x 3-93500 RPM
5 x 6-73500 RPM
5 x 6-71750 RPM
6 x 8-91/2
1750 RPM
11/4 x 11/2-91/2
3500 RPM
4
300
200
100
0
90
20
0
40
60
80
0
0 120
600300100
10080604020CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
ÍNAM
ICA
TOTA
L)
METERSMETROS
FEETPIES
GPM
m3/hr
250
3 x 4-850
150
30
50
70
10
500400200
3 x 4-10
21/2 x 3-8
21/2 x 3-13
21/2 x 3-7
11/2 x 2-1021/2 x 3-9
21/2 x 3-10
11/2 x 2-10 (1750)21/2 x 3-8 (1750)21/2 x 3-9 (1750)
21/2 x 3-10 (1750)21/2 x 3-13 (1750)
3 x 4-8 (1750)3 x 4-10 (1750)
2 x 21/2-7 (1750)11/4 x 11/2-91/2 (1750)
11/4 x 11/2-91/2
2 x 21/2-7
Performance Coverage, Campo de desempeño
Goulds PumpsAg. / Irrigation
5
Pump Reference Numbers, Pump Reference Numbers
The following Pump Reference Number is provided to help you quickly find the performance curve, dimensions and price for your Ag-Flo selection. Pump curves are listed in discharge order and grouped by operating speed.
Example Pump Reference Number, Ejemplo Pump Reference Number 1 CC 10 MS
The following Pump Reference Number is provided to help you quickly find the performance curve, dimensions and price for your Ag-Flo selection. Pump curves are listed in discharge order and grouped by operating speed.
DischargeSize (inches)
ConfigurationCC = Close Coupled
FRM = Frame MountedSAE = Engine Mount
MaximumImpeller
Size (inches)
MS = Mechanical SealPK = Packed Box
6
Performance Curves, Curvas de desempeño
NOTE: Not recommended for operationbeyond printed H-Q curve.NOTA: No se recomienda la operación más alláde la curva impresa de H-Q (carga-capacidad).
Model 1CC7MS / Size (Tamaño) 1 x 2 – 73500 RPM Curve (Curva) CN0724R00
D 53/4
A 63/4'' DIA.
B 67/16
C 6
E 51/2
F 51/16
G 413/16
H 49/16
J 43/8K 41/16
L 313/16
58%
NPSH FEET (PIES)40% EFF 46% 50% 56%
50%
8'
10'
5 HP
20'
3 HP
2 HP
1 HP1.5 HP
54%
54%
46%
0
20
80
100
60
40
0
0
800
m3/hr
U.S. GPM
25
6040
5 15
20 100
120
140
120
10 20
160
180
10
20
30
40
5060%
58%
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
60%
56%
6'
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 6¾" B 67⁄16
C 6
D 5¾ E 5½ F 51⁄16
7⁄8" G 413⁄16
H 49⁄16
J 43⁄8 K 41⁄16
L 313⁄16
NOTE: Pump will pass a sphere to 3⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 3⁄16 de pulgada de diámetro.
Goulds PumpsAg. / Irrigation
0
50
0
90
0
120706040200
10 m3∨hr
U.S. GPM
20 25
10 30 50
300
50
10
155
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
250
200
150
100
80 90 110100
20
30
40
60
70
80
30 35 4045 % EFF
6'
71/2 HP
50
A 81/16'' DIA.
B 75/16
C 61/2
D 53/8
50
10'
10 HP
5 HP
3 HP
Model 1CC8MS / Size (Tamaño) 1 x 2 – 83500 RPM Curve (Curva) CN0722R00
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda la operación más allá de lacurva impresa de H-Q (carga-capacidad).
4' NPSHR – FEET (PIES)
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 81⁄16" B 75⁄16
C 61⁄2
7⁄8"
D 53⁄8
NOTE: Pump will pass a sphere to 3⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 3⁄16 de pulgada de diámetro.
7
00
150
0
2206040200
10 m3∨hr
U.S. GPM
20 45
500
50
155
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
250
200
150
100
80 100
50
300
350
400
450
100
120 140 160 180 200
25 30 35 40
0
10
20
0
25
50
NPSH
IN F
EET
(NPS
H PIE
S)
NPSH
IN M
ETER
S (N
PSH
MET
ROS)
30 40% EFF45A 91/2'' DIA.
B 9
C 81/2
D 8
50
10 HP
5357
58
E 71/2
15 HP
20 HP
25 HP
30 HP
NPSH REQ
71∨2 HP
F 7
57
55 56
56
55
53
50
Model 11/4CC91/2MS / Size (Tamaño) 11/4 x 11/2 – 91/23525 RPM Curve (Curva)
NOTE: Not recommended for operationbeyond printed H-Q curve.NOTA: No se recomienda la operación más alláde la curva impresa de H-Q (carga-capacidad).
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 9½" B 9 C 8½
7⁄8"
D 8 E 7½ F 7
NOTE: Pump will pass a sphere to 3⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 3⁄16 de pulgada de diámetro.
Performance Curves, Curvas de desempeño
A 515/16" DIA.
B 51/8" % EFF
NPSHR – FEET (PIES)
11/2CC6MS / Size (Tamaño) 11/2 x 2 – 63500 RPM Curve (Curva) CN0747R00
5040
60 65
70
70
72
7273
65
5.5'
10' 12'
14'16'
18'
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda la operación más allá de la curvaimpresa de H-Q (carga-capacidad).
5 HP
3 HP
0
40
80
120
160
0
10
20
30
40
50
0
18016012080400
10 20 m3∨hr
U.S. GPM
30 40
20 60 100 140
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
6'8'7'
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 515⁄16" 7⁄8" B 51⁄8
NOTE: Pump will pass a sphere to 5⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄16 de pulgada de diámetro.
3500 R
PM
8
Performance Curves, Curvas de desempeño
Goulds PumpsAg. / Irrigation
A 515/16" DIA.
B 55/8"
NPSHR – FEET (PIES)
0
40
80
120
160
0
10
20
30
40
50
0
12080400
10 20 m3∨hr
U.S. GPM
30
20 60 100 160140
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
% EFF
11/2CC6HMS / Size (Tamaño) 11/2 x 2 – 6H 3500 RPM Curve (Curva) CN0748R00H = High Head Impeller H = Impulsor de carga alta
3 HP
40
5.5'
8'
10'
12'
14'16'
18'
40
50
50
60
60
65
65
67
67
6'
7'
NOTE: Not recommended for operation beyondprinted H-Q curve.May utilize 1.15 motor service factor.
NOTA: No se recomienda la operación más allá de lacurva impresa de H-Q (carga-capacidad).Puede utilizar factor de servicio 1.15.
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 515⁄16" 7⁄8" B 51⁄8
NOTE: Pump will pass a sphere to 5⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄16 de pulgada de diámetro.
15 HP
% EFF
A 81/16" DIA.
50
7 1/2 HP
10 HP
10'
5 HP
20 HP
504060
60
65
65
67
70
8'12' 14'
16'
18'
20'22'
F 7"
G 61/4"
D 53/4"
NPSHR – FEET (PIES)
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda la operación más allá de lacurva impresa de H-Q (carga-capacidad).
Model 11/2CC8MS / Size (Tamaño) 11/2 x 2 – 83500 RPM
E 73/4"
B 75/8"
C 63/4"
H 61/8"
0
50
100
300
0
20
60
80
0
250150500
10 20 m3/hr
U.S. GPM
60
100 200
30 40 50
250
200
150
40
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 81⁄16" E 7¾ B 75⁄8
F 7 7⁄8" C 6¾ G 6¼ H 61⁄8 D 5¾
NOTE: Pump will pass a sphere to 5⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄16 de pulgada de diámetro.
9
0
20
300
0
200
100
500160
400
100
NOTE: Not recommended for operationbeyond printed H-Q curve.NOTA: No se recomienda para funcionamiento superior al impreso en la curva H-Q.
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
40
60
80
120
140
0 10
200150100500
20 4030 m3/hr
U.S. GPM
CAPACITY (CAPACIDAD)
250 300
50 60
25 HP
30 HP
40 HP
20 HP
15 HP
A 101/16" DIA.
B 93/16"
C 83/8"
D 73/4"
E 71/4"F 7"
54
50 % EFF
58
60
54
58
NPSHR – FEET (PIES)10'
12'
14' 16'
8'
Model 11/2CC10MS / Size (Tamaño) 11/2 x 2 – 103500 RPM Curve (Curva) CN0207R01
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 101⁄16" B 93⁄16
C 83⁄8 1¼" D 7¾ E 7¼ F 7
NOTE: Pump will pass a sphere to 5⁄32" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄32 de pulgada de diámetro.
Performance Curves, Curvas de desempeño
0 10
120100806040200
30% EFF NPSHR – FEET (PIES)
0
B 37/8"15
180
20 30
10
50
40
10
0
3/4
43
2CC5MS / Size (Tamaño) 2 x 2-5RPM 3450 Curve (Curva) CN0703R00
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INAM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
m3∨hr
U.S. GPM
NOTE: Not recommended for operation beyond printedH-Q curve.NOTA: No se recomienda para funcionamiento superior alimpreso en la curva H-Q.
140 160
40
30
20
5
A 4" DIA.
50 5560
60
64
64
5'
6'
7'
9'
1 1/2 HP
1 HP
2 HP
C 31/2"
D 31/4"
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 4" B 37⁄8" 7⁄8" C 31⁄2" D 31⁄4
NOTE: Pump will pass a sphere to 5⁄32" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄32 de pulgada de diámetro.
3500 R
PM
10
Performance Curves, Curvas de desempeño
Goulds PumpsAg. / Irrigation
0
24020016012080400
40% EFF NPSHR – FEET (PIES)
0
B 315/16"
15
10
40
10
0
1 1/2 HP
21/2CC5MS / Size (Tamaño) 21/2 x 21/2-5RPM 3450 Curve (Curva) CN0705R00
m3∨hr
U.S. GPM280 320
80
5
A 43/16" DIA.
13'
50
30
20
10
360
20 30 40 50 60 70
1 HP
2 HP
3 HP
11'
9'50
60
60
65
65
72
72C 33/4"
D 39/16"
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INAM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
NOTE: Not recommended for operation beyond printedH-Q curve.NOTA: No se recomienda para funcionamiento superior alimpreso en la curva H-Q.
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 43⁄16" B 315⁄16 7⁄8" C 33⁄4 D 39⁄16
NOTE: Pump will pass a sphere to 5⁄32" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄32 de pulgada de diámetro.
00
60
0
450150100500
m3∨hr
U.S. GPM
20 100
220
40
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
120
100
80
60
200 250
20
140
160
180
200
50
300 350 400
40 60 80
0
8
12
0
20
40
NPSH
IN F
EET
(NPS
H PIE
S)
NPSH
IN M
ETER
S (N
PSH
MET
ROS)
40
30
20
10
4
40 50% EFF
60A 7'' DIA.
B 61/2
C 6
D 51/2
65
10 HP
70
74
15 HP
20 HP
NPSH REQ
71/2 HP
E 5
72 73
5 HP
68
7474
7273
7068
Model 2CC7MS / Size (Tamaño) 2 x 21/2 – 73500 RPM Curve (Curva)
NOTE: Not recommended for operationbeyond printed H-Q curve.NOTA: No se recomienda la operación más alláde la curva impresa de H-Q (carga-capacidad).
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 7" B 6½ C 6 7⁄8" D 5½ E 5
NOTE: Pump will pass a sphere to 5⁄32" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄32 de pulgada de diámetro.
11
Performance Curves, Curvas de desempeño
00
0
0
m3∨hr10
100
50
100
250
10
20
30
50
70
90
40
U.S. GPM
150
200
40035030025020015050
60
20 30 40 50 60 70 80
Model 21/2CC7MS / Size (Tamaño) 21/2 x 3 – 73450 RPM Curve (Curva) CN0709R00
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamiento superioral impreso en la curva H-Q.
METERSMETROS
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
64
6'60
70
68
71
10'12' 14'
68
70
71
NPSHR – FEET (PIES)
8'
16' 18'
5 HP
7.5 HP
10 HP
15 HP
A 71/16'' DIA.B 67/8''
C 6''
D 57/16''
E 43/4''
F 41/16''
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 71⁄16" B 67⁄8 C 6 7⁄8" D 57⁄16
E 43⁄4 F 41⁄16
NOTE: Pump will pass a sphere to 7⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 7⁄16 de pulgada de diámetro.
0
0 40
400150100500
40
60 100
250
0
80 m3/hr
U.S. GPM
200
100
80
300
60
50
150
200 250 300 350
20
20
50
F 63/16"
NOTE: Not recommended for operation beyond printed H-Q curve.NOTA: No se recomienda para funcionamiento superior al impresoen la curva H-Q.
METERSMETROS
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
A 715/16" DIA.
B 77/16"
C 73/16"
D 613/16"
E 63/8"25 HP
20 HP
15 HP
70
65
60
737578
15' 18'
75
10'
7812'
607'
65 70
73
8'
40% EFF
NPSHR – FEET (PIES)6'
Model 21/2CC8MS / Size (Tamaño) 21/2 x 3 – 83500 RPM Curve (Curva) CN208R00
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 715⁄16" B 77⁄16 11⁄4" C 73⁄16
D 613⁄16
E 63⁄8 7⁄8"
F 63⁄16
NOTE: Pump will pass a sphere to 5⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄16 de pulgada de diámetro.
3500 R
PM
12
0
0
3002001000
250
0
180
Model 21/2CC9MS / Size (Tamaño) 21/2 x 3 – 93550 RPM Curve (Curva) CN0715R00
m3∨hr
U.S. GPM
150
50
90
70
400 500 600 700
40 80 160140120100
200
10020
30
6020
800
200
450
80
60
50
40
10
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamientosuperior al impreso en la curva H-Q.
METERSMETROS
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
400
350
300
60 % EFF
65
68
70
65
8' NPSHR – FEET (PIES)
10'14'
16'
20'
50 HP
40 HP
30 HP
25 HP20 HP
60 HP
K 101/16" DIA.L 97/8"
M 91/2"
N 81/2"
P 83/16"
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
K 101⁄16" L 97⁄8 M 91⁄2 11⁄4" N 81⁄2 P 83⁄16
NOTE: Pump will pass a sphere to 5⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄16 de pulgada de diámetro.
0
0
8003002001000
500
0
175
Model 21/2CC10MS / Size (Tamaño) 21/2 x 3 – 103550 RPM Curve (Curva) CN0717R00
m3∨hr
U.S. GPM
300
100
180
80
400 500 600 700
75 150125100
400
200
40
60
5025
120
100
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamiento superioral impreso en la curva H-Q.
METERSMETROS
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
75 HP
60 HP
50 HP
40 HP
30 HP
K 101/16" DIA.
L 95/8"
N 9"
P 85/8"
R 8"
S 71/8"
10'12' 14' 16'
18'20'
22'
NPSHR – FEET (PIES)
64 % EFF70 72 74
76
7674
25 HP
140
160
20
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
K 101⁄16" L 95⁄8
N 9 11⁄4" P 85⁄8 R 8 S 71⁄8
NOTE: Pump will pass a sphere to 5⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄16 de pulgada de diámetro.
Performance Curves, Curvas de desempeño
Goulds PumpsAg. / Irrigation
13
Performance Curves, Curvas de desempeño
% EFF
Model 3CC7MS / Size 3 x 4-73500 RPM Curve (Curva) CN0727R00
B 63/8" DIA.
7 1/2 HP
E 51/8"
D 51/2"
10 HP
6'
50
15 HP
50
60
60 65
65
68
68 70
70
8'
10'12'
74
NPSHR – FEET (PIES)
NOTE: Not recommended for operation beyondprinted H-Q curve.May utilize 1.15 motor service factor.
NOTA: No se recomienda la operación más allá de lacurva impresa de H-Q (carga-capacidad).Puede utilizar factor de servicio 1.15.
0
25
75
175
0
20
40
0
6000
10 20 m3∨hr
U.S. GPM
150
100 200
30 40 50
150
125
10030
500400300
1007060
10
50
60
1401301201109080
50
200
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
B 63⁄8" D 51⁄2
7⁄8" E 51⁄8
NOTE: Pump will pass a sphere to 1⁄2" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 1⁄2 de pulgada de diámetro.
0
300250200150100500
40% EFF
NPSHR – FEET (PIES)
0
B 43/16"
15
20
0
2 HP
3CC5MS / Size (Tamaño) 3 x 3-5RPM 3450 Curve (Curva) CN350R00
m3∨hr
U.S. GPM350 400
100
A 43/8" DIA.
C 4"
D 313/16"
450
60 80
12'
5
50
40
30
20
10
10
40
5260
68
14'
18'
68
74
74
3 HP
5 HP
E 35/8"
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INAM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
NOTE: Not recommended for operation beyond printedH-Q curve.NOTA: No se recomienda para funcionamiento superior alimpreso en la curva H-Q.
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 43⁄8" B 43⁄16
C 4 7⁄8" D 313⁄16 E 35⁄8
NOTE: Pump will pass a sphere to 5⁄32" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄32 de pulgada de diámetro.
3500 R
PM
14
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda la operación más allá de la curva impresa de H-Q (carga-capacidad).
50
100
0
100
0
10002000
50 m3/hr
U.S. GPM0
50
300 400 500 600 700 800 900 1100 1200100
150
200
250
300
350
400
30 HP40 HP
50 HP60 HP
75 HP
60% EFF. 7074 76
7880
8078
70
7476
60
11'
13'
15'
18'
20'
NPSHR – FEET (PIES)10'
H 83/4
J 89/16
K 81/8
L 73/4M 75/8
N 71/4
R 63/4
G 91/8 DIA.
P 71/16
350300250200150100
METERSMETROS
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
Model 3CC10MS / Size (Tamaño) 3 x 4 – 103550 RPM
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
G 91⁄8" H 8¾
J 89⁄16
K 81⁄8 L 7¾ 1¼" M 75⁄8 N 7¼ P 71⁄16
R 6¾
NOTE: Pump will pass a sphere to 1⁄2" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 1⁄2 de pulgada de diámetro.
Performance Curves, Curvas de desempeño
Goulds PumpsAg. / Irrigation
0
0
8003002001000
250
0
11'
180
45% EFF
m3/hr
U.S. GPM
150
50
90
70
400 500 600 700
40 80 160140120100
200
100
20
30
58
6020
900
200
300
80
60
50
40
10
13'6873
73
68
58
76
7616' 21'
27'40 HP
50 HP
25 HP20 HP15 HP
10 HP7 1/2 HP
30 HP
B 77/16"
A 81/16" DIA.
D 63/4"
E 63/8"
F 515/16"
H 51/8"
J 45/8"
G 51/2"
NPSHR – FEET (PIES)
NOTE: Not recommended for operation beyond printedH-Q curve.NOTA: No se recomienda para funcionamiento superior al impresoen la curva H-Q.
METERSMETROS
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
Model 3CC8MS / Size (Tamaño) 3 x 4 – 83500 RPM Curve (Curva) CN374R00
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 81⁄16" B 77⁄16
D 6¾ E 63⁄8 1¼" F 515⁄16
G 5½ H 51⁄8 J 45⁄8
NOTE: Pump will pass a sphere to 3⁄8" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 3⁄8 de pulgada de diámetro.
15
0
0
16006004002000
40
250
0
20'
350
% EFF
m3/hr
U.S. GPM
200
100
80275
30 HP
60
50
150
800 1000 1200 1400
50
20
100 300250200150
225
175
125
75
2510
30
50
70
50
40 HP
50 HP
60 HP
75 HP
60
60
70
7075
7578
78
80
8082 22'
24'
26'
30'
A 77/8" DIA.B 73/4"
C 71/2"
D 71/4"
E 7"
F 63/4"
G 61/2"
H 61/16"
J 53/4"
NPSHR – FEET (PIES)
NOTE: Not recommended for operation beyond printedH-Q curve.NOTA: No se recomienda para funcionamiento superior al impresoen la curva H-Q.METERS
METROSFEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
Model 4CC8MS / Size (Tamaño) 4 x 5 – 83550 RPM Curve (Curva) CN0078R00
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 77⁄8" B 7¾
C 6½
D 63⁄16
E 7 1¼" F 6¼ G 6½ H 61⁄16
J 5¾
NOTE: Pump will pass a sphere to 5⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄16 de pulgada de diámetro.
Performance Curves, Curvas de desempeño
0
3002502001501005000
15
20
0
4CC5MS / Size (Tamaño) 4 x 4-5RPM 3450 Curve (Curva) CN666R00
m3∨hr
U.S. GPM350 400
140
700
60 80
5
50
40
30
20
10
10
40
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INAM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
NOTE: Not recommended for operation beyond printedH-Q curve.NOTA: No se recomienda para funcionamiento superior alimpreso en la curva H-Q.
450 500 550 600 650
60
120100
20
B 45/8"
A 413/16" DIA.
C 41/2"
D 43/16"E 4"
5 HP
3 HP
7 1∨2 HP
55% EFF60 66
7072
747274
70
66
60
NPSHR – FEET (PIES)10'18'
22'26'
28'
14'
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 413⁄16" B 45⁄8 C 41⁄2
7⁄8" D 43⁄16 E 4
NOTE: Pump will pass a sphere to 5⁄32" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄32 de pulgada de diámetro.
3500 R
PM
16
0
30020010000
15
0
5CC6MS / Size (Tamaño) 5 x 5-6RPM 3450 Curve (Curva) CN669R00
m3∨hr
U.S. GPM400
200
1000
50
5
50
40
30
20
10
10
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INAM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
NOTE: Not recommended for operation beyond printedH-Q curve.NOTA: No se recomienda para funcionamiento superior alimpreso en la curva H-Q.
500 600 700 800 900
60
150100
20
70
C 5" x 37/8"
B 55/16" x 45/16"
D 5" x 39/16"
E 5" x 31/32"
71/2 HP10 HP
54% EFF 6065
70
72
68
72
68
70
65
62 NPSHR – FEET (PIES)15' 18'
20'
26'
24'
15 HP
A 51/2" x 41/2" DIA.
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 51⁄2" x x 41⁄2" B 55⁄16 x 45⁄16
C 5 x 37⁄8 7⁄4" D 5 x 39⁄16 E 5 x 31⁄32
NOTE: Pump will pass a sphere to 5⁄32" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄32 de pulgada de diámetro.
Performance Curves, Curvas de desempeño
Goulds PumpsAg. / Irrigation
00
60
0
18006004002000
m3∨hr
U.S. GPM
50 400
200
40
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
120
100
80
60
800 1000
20
140
160
180
50
1200 1400 1600
100 200 300
0
8
16
0
20
40
NPSH
IN F
EET
(NPS
H PIE
S)
NPSH
IN M
ETER
S (N
PSH
MET
ROS)
40
30
20
10
4
150 250 350
12
50
80
% EFF 60A 7'' DIA.
B 61/2
C 6
D 51/2
65
30 HP
7075
40 HP
25 HP
NPSH REQ
7378
75
73
70
78
50 HP
60 HP
65
Model 5CC7MS / Size (Tamaño) 5 x 6 – 73550 RPM Curve (Curva)
NOTE: Not recommended for operationbeyond printed H-Q curve.NOTA: No se recomienda la operación más alláde la curva impresa de H-Q (carga-capacidad).
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 7" B 6½ 1¼" C 6
D 5½
NOTE: Pump will pass a sphere to 1⁄2" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 1⁄2 de pulgada de diámetro.
17
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda la operación más allá de lacurva impresa de H-Q (carga-capacidad).
Model 1CC7MS / Size (Tamaño) 1 x 2 – 71750 RPM
0
10
40
50
30
20
0
60200U.S. GPM
15
10 40 7030 50
5 10
0
15
10
5
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)m3/hr
30% EFF40%
47%52%
2' NPSH55%
.5 HP
.75 HP
47%
4'55%18'
52%
A 63/4'' DIA.
B 67/16
C 6
D 53/4
E 51/2
F 51/16
G 413/16
H 49/16
J 43/8K 41/16
L 313/16
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 6¾" B 57⁄8 C 5¼
D 413⁄16
E 5½ F 51⁄16
7⁄8" G 413⁄16
H 49⁄16
J 43⁄8 K 41⁄16
L 313⁄16
NOTE: Pump will pass a sphere to 3⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 3⁄16 de pulgada de diámetro.
Performance Curves, Curvas de desempeño
0
10
0
20
0
75706040200
6 10 m3∨hr
U.S. GPM
14 16
10 30 50 65
20
40
30
70
5
50
60
15
10
45255 15 35 55
12842
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
25 30 3540
45
% EFF
4'
45
1 1/2 HP
1 HP
3/4 HP
1/2 HP
20A 81/16'' DIA.
B 75/16
C 61/2
D 53/8
Model 1CC8MS / Size (Tamaño) 1 x 2 – 81750 RPM Curve (Curva) CN0723R00
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda la operación más allá de lacurva impresa de H-Q (carga-capacidad).
NPSHR – FEET (PIES) 3’
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 81⁄16" B 75⁄16
C 61⁄2
7⁄8"
D 53⁄8
NOTE: Pump will pass a sphere to 3⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 3⁄16 de pulgada de diámetro.
1750 R
PM
18
11/2CC6MS / Size (Tamaño) 11/2 x 2 – 61750 RPM Curve (Curva) CN0749R00
3'
3/4 HP
1/2 HP
4'
5'
9'
50
60
65
68
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda la operación más allá de lacurva impresa de H-Q (carga-capacidad).
68
5
10
15
2
10
0
90806040200
5 10 m3∨hr
U.S. GPM
15 20
10 30 50 70
20
25
30
35
4
6
8
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
% EFF 50
A 515/16" DIA.
B 51/8"
NPSHR – FEET (PIES)
6065
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 515⁄16" 7⁄8" B 51⁄8
NOTE: Pump will pass a sphere to 5⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄16 de pulgada de diámetro.
Performance Curves, Curvas de desempeño
Goulds PumpsAg. / Irrigation
00
35
0
1406040200
10 m3∨hr
U.S. GPM
20 30
120
10
155
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
100
80
60
40
80 100
20
120
25
0
5
10
0
10
20
NPSH
IN F
EET
(NPS
H PIE
S)
NPSH
IN M
ETER
S (N
PSH
MET
ROS)
30
25
15
20
5
30
40
% EFF
45A 91/2'' DIA.
B 9
C 81/2
D 8
50
1 HP
53
57 57
E 71/2
NPSH REQ
11/2 HP
F 7
57
55 56
5655
53
50
2 HP
3 HP
5 HP
Model 11/4CC91/2MS / Size (Tamaño) 11/4 x 11/2 – 91/21750 RPM Curve (Curva)
NOTE: Not recommended for operationbeyond printed H-Q curve.NOTA: No se recomienda la operación más alláde la curva impresa de H-Q (carga-capacidad).
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 9½" B 9 C 8½
7⁄8"
D 8 E 7½ F 7
NOTE: Pump will pass a sphere to 3⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 3⁄16 de pulgada de diámetro.
19
A 515/16" DIA.
B 55/8"
% EFF
11/2CC6HMS / Size (Tamaño) 11/2 x 2 – 6H1750 RPM Curve (Curva) CN0750R00H = High Head Impeller H = Impulsor de carga alta
403'
1/2 HP
50
50
55
5560
60
66
664'
5'
6'
7'
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda la operación más allá de lacurva impresa de H-Q (carga-capacidad).
NPSHR – FEET (PIES)
5
10
15
2
10
0
806040200
5 10 m3∨hr
U.S. GPM
15 20
10 30 50 70
20
25
30
35
4
6
8
9
7
5
3
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 515⁄16" 7⁄8" B 51⁄8
NOTE: Pump will pass a sphere to 5⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄16 de pulgada de diámetro.
A 81/16" DIA.
C 75/8"
E 63/4"
G 53/4"
% EFF
NPSHR – FEET (PIES)
Model 11/2CC8MS / Size (Tamaño) 11/2 x 2 – 81750 RPM Curve (Curva) CN0729R00
50 3'
3/4 HP
1 HP
2 HP
1 1/2 HP
60
60
70
70
72
5'
7'
11'
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda la operación más allá de lacurva impresa de H-Q (carga-capacidad).
20
30
5
20
0
16012080400
10 20 m3∨hr
U.S. GPM
30 40
20 60 100 140
40
50
60
70
10
15
10
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 81⁄16" C 75⁄8 7⁄8" E 63⁄4 G 53⁄4
NOTE: Pump will pass a sphere to 5⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄16 de pulgada de diámetro.
Performance Curves, Curvas de desempeño
1750 R
PM
20
Performance Curves, Curvas de desempeño
Goulds PumpsAg. / Irrigation
10
0
16010090800
15
110
5
5'
35
30% EFF
m3/hr
U.S. GPM
100
35120
25
20
120 130 140 150
5 10 30252015
3010
20
30
5 HP
40
50
60
70
80
90
11070605040302010
F 7"
3540 42
45
4542
40
35
47
4748
486'
7'
3 HP
2 HP
A 101/16" DIA.
B 93/16"
C 83/8"
D 73/4"
NPSHR – FEET (PIES)
NOTE: Not recommended for operationbeyond printed H-Q curve.NOTA: No se recomienda para funcionamientosuperior al impreso en la curva H-Q.
METERSMETROS
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
Model 11/2CC10MS / Size (Tamaño) 11/2 x 2 – 101750 RPM
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 101⁄16" B 93⁄16
C 83⁄8 7⁄8" D 83⁄4 F 7
NOTE: Pump will pass a sphere to 5⁄32" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄32 de pulgada de diámetro.
0 5
6050403020100
30% EFF
NPSHR – FEET (PIES)
0
4
10 15
103
0
1/4
2CC5MS / Size (Tamaño) 2 x 2-5RPM 1725 Curve (Curva) CN0704R00
m3∨hr
U.S. GPM70 80
20
5
2
A 4" DIA.
3'
5'
6'
40
30
48
52
5256
56
4840
1
C 31/2"
D 31/4"
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INAM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
NOTE: Not recommended for operation beyond printedH-Q curve.NOTA: No se recomienda para funcionamiento superior alimpreso en la curva H-Q.
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 4" C 31⁄2
7⁄8" D 31⁄4
NOTE: Pump will pass a sphere to 5⁄32" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄32 de pulgada de diámetro.
21
Performance Curves, Curvas de desempeño
00
16
0
250150100500
m3∨hr
U.S. GPM
10 50
60
12
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
200
20
14
20 30 40
0
6
0
20
10
NPSH
IN F
EET
(NPS
H PIE
S)
NPSH
IN M
ETER
S (N
PSH
MET
ROS)
40
10
8
6
410
30
50
4
2 2
40 50% EFF
60A 7'' DIA.
B 61/2
C 6
D 51/2
6568
69
NPSH REQ
11/2 HP
E 5
68
69
3 HP
67
67
3∨4 HP
1 HP
2 HP
55
40
50
55
65
60
69.5
Model 2CC7MS / Size (Tamaño) 2 x 21/2 – 71750 RPM Curve (Curva)
NOTE: Not recommended for operationbeyond printed H-Q curve.NOTA: No se recomienda la operación más alláde la curva impresa de H-Q (carga-capacidad).
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 7" B 6½ C 6 7⁄8" D 5½ E 5
NOTE: Pump will pass a sphere to 5⁄32" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄32 de pulgada de diámetro.
0
120100806040200
40% EFF NPSHR – FEET (PIES)
0
B 315/16"
4
10
10
0
1/4 HP
21/2CC5MS / Size (Tamaño) 21/2 x 21/2-5RPM 1725 Curve (Curva) CN0706R00
m3∨hr
U.S. GPM140 160
40
1
A 43/16" DIA.
5
180
20 30
4'
3
2
5060
64
64
60
67
67
4.5'
5'
6'
1/2 HP
1/3 HP
C 33/4"
D 39/16"
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INAM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
NOTE: Not recommended for operation beyond printedH-Q curve.NOTA: No se recomienda para funcionamiento superior alimpreso en la curva H-Q.
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 43⁄16" B 315⁄16 7⁄8" C 33⁄4
D 39⁄16
NOTE: Pump will pass a sphere to 5⁄32" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄32 de pulgada de diámetro.
1750 R
PM
22
0
30
40
0
0
0
m3∨hr
20 100
60
10
12
16
18
45
14
U.S. GPM
20
200
50
10
120 140 160 18040 60 80
2
4
6
8
403530252015105
64 6668
70
60
7068
66
64
Model 21/2CC7MS / Size (Tamaño) 21/2 x 3 – 71750 RPM Curve (Curva) CN0711R00
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamiento superioral impreso en la curva H-Q.
METERSMETROS
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
1/2 HP
3' NPSHR – FEET (PIES)
4'5'
6'
11/2 HP
2 HP
3/4 HP1 HP
C 6''
D 57/16''
A 71/16" DIA.
B 67/8"
E 43/4''
F 41/16''
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 71⁄16" B 67⁄8 C 6 7⁄8" D 57⁄16
E 43⁄4 F 41⁄16
NOTE: Pump will pass a sphere to 7⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 7⁄16 de pulgada de diámetro.
15
0
3202001801600
15
65
5
70 m3/hr
U.S. GPM
60
20
70
20
240 260 280 300
20 60
30
10
40
50
55
22014012010080604020
45
35
25
40 503010
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamiento superioral impreso en la curva H-Q.
METERSMETROS
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
A 715/16" DIA.
B 77/16"
C 73/16"
D 613/16"
F 63/16"
5 HP
3 HP
2 HP
68
66
64
60
55
50
8'
9'
10'
11'
50% EFF 55 6064
66
6'4' NPSHR – FEET (PIES)
Model 21/2CC8MS / Size (Tamaño) 21/2 x 3 – 81750 RPM
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 715⁄16" B 77⁄16
C 73⁄16 7⁄8"
D 613⁄16
F 63⁄16
NOTE: Pump will pass a sphere to 5⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄16 de pulgada de diámetro.
Performance Curves, Curvas de desempeño
Goulds PumpsAg. / Irrigation
23
Performance Curves, Curvas de desempeño
0
0
1501005000
90
Model 21/2CC9MS / Size (Tamaño) 21/2 x 3 – 91750 RPM Curve (Curva) CN0716R00
m3∨hr
U.S. GPM
20
30
200 250 300 350
20 40 80706050
100
20
3010
400
100
120
10
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamientosuperior al impreso en la curva H-Q.
METERSMETROS
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
64 % EFF 6566
70
A&K 101/16" DIA.
B&L 97/8"C 91/2"
D 81/2"
E 83/16"
3 HP
5 HP
71/2 HP
4'
8'
40
60
80
NPSHR – FEET (PIES)3'
70
68
68
5'
66
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 101⁄16" B 97⁄8 C 91⁄2 7⁄8" D 81⁄2 E 83⁄16
K 101⁄16 11⁄4" L 97⁄8
NOTE: Pump will pass a sphere to 5⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄16 de pulgada de diámetro.
Model 21/2CC10MS / Size (Tamaño) 21/2 x 3 – 101750 RPM Curve (Curva) CN0751R00
10
0
4002001500
15
5
90 m3∨hr
U.S. GPM
60
35130
20
250 300 350
20 60
3010
40
50
10050
40 503010 8070
70
80
90
110
100
20
25
30
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamiento superioral impreso en la curva H-Q.
METERSMETROS
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
120
00
10 HP
71/2 HP
5 HP3 HP
A&K 101/16" DIA.
B&M 91/2"
C 81/4"
D 71/8"
6' NPSHR – FEET (PIES)
8'
10'
62 % EFF65
70
7272
70
65
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 101⁄16" B 91⁄2 7⁄8" C 81⁄4 D 71⁄8 K 101⁄16 11⁄4" M 91⁄2
NOTE: Pump will pass a sphere to 5⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄16 de pulgada de diámetro.
1750 R
PM
24
0
0
8003002001000
200
0
180
% EFF
m3/hr
U.S. GPM
120
100
60
30
400 500 600 700
40 80 160140120100
160
10
20
50
6020
50
40
20 HP
180
140
80
60
40
20
50
55
5560
6063
6365
65
12'
16'
20'
40
15 HP
10 HP
8'
A 131/16" DIA.
B 123/4"
C 117/8"
D 113/8"
E 97/8"
F 93/8"
NPSHR – FEET (PIES)
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamientosuperior al impreso en la curva H-Q.
METERSMETROS
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
Model 21/2CC13MS / Size (Tamaño) 21/2 x 3 – 131750 RPM Curve (Curva) CN0104R00
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 131⁄16" B 12¾ C 117⁄8 1¼" D 113⁄8 E 97⁄8 F 93⁄8
NOTE: Pump will pass a sphere to 5⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄16 de pulgada de diámetro.
Performance Curves, Curvas de desempeño
Goulds PumpsAg. / Irrigation
0
1501251007550250
40% EFF NPSHR – FEET (PIES)
0
B 43/16"
4
10
0
3CC5MS / Size (Tamaño) 3 x 3-5RPM 1725 Curve (Curva) CN351R00
m3∨hr
U.S. GPM175 200
50
A 43/8" DIA.
C 4"
D 313/16"
E 35/8"
225
30 40
4'
1
10
5
20
50
1/4 HP
3
2
60
68
68
74
74
6'
10'
1/3 HP
1/2 HP
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INAM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
NOTE: Not recommended for operation beyond printedH-Q curve.NOTA: No se recomienda para funcionamiento superior alimpreso en la curva H-Q.
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 43⁄8" B 43⁄16
C 4 7⁄8" D 313⁄16
E 35⁄8
NOTE: Pump will pass a sphere to 5⁄32" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄32 de pulgada de diámetro.
25
0
0
4504000
A 81/16" DIA.
15
80
0
6'
100
45% EFF
m3/hr
U.S. GPM
60
30 100
20
20 60
10
40
35030025020015010050
58
8040
7 1/2 HP
5 HP
25
20
5
10 30 50 70 90
68 7376
7673
6858
8'
4'
3 HP2 HP1 HP
C 77/16"
D 63/4"
E 63/8"
F 515/16"
G 51/2"
H 51/8"
J 45/8"
NPSHR – FEET (PIES)
NOTE: Not recommended for operation beyond printedH-Q curve.NOTA: No se recomienda para funcionamiento superior al impresoen la curva H-Q.
METERSMETROS
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
Model 3CC8MS / Size (Tamaño) 3 x 4 – 81750 RPM Curve (Curva) CN375R00
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 81⁄16" C 77⁄16
D 6¾
E 63⁄8 7⁄8" F 515⁄16
G 5½ H 51⁄8 J 45⁄8
NOTE: Pump will pass a sphere to 3⁄8" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 3⁄8 de pulgada de diámetro.
Performance Curves, Curvas de desempeño
A 71/16" DIA.
B 63/8"
E 51/8"
NPSHR – FEET (PIES)
% EFF
Model 3CC7MS / Size (Tamaño) 3 x 4 – 71750 RPM Curve (Curva) CN0728R00
355'
1 1/2 HP 1 HP
2 HP
3 HP
4860
60
65
65
67
67
4'
8'
16'
C 6"
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda la operación más allá de lacurva impresa de H-Q (carga-capacidad).
10
20
0
15
0
3002001000
10 20 m3∨hr
U.S. GPM
40 90
50 150 250 350
30
40
50
0
10
5
30 50 60 70 80
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 71⁄16" B 63⁄8 7⁄8" C 6 E 51⁄8
NOTE: Pump will pass a sphere to 1⁄2" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 1⁄2 de pulgada de diámetro.
1750 R
PM
26
0
0
8003002001000
200
0
180 m3/hr
U.S. GPM
120
100
60
30
400 500 600 700
40 80 160140120100
160
10
20
6020
50
40
30 HP
900
200
180
140
80
60
40
20
7075
5'
6'
7878
75
70
60
8'
10' 12'
50
25 HP20 HP15 HP10 HP7 1/2 HP
% EFF60
4'
A 131/16" DIA.
C 125/16"
E 113/4"
G 103/4"
J 91/8"
L 8"
NPSHR – FEET (PIES)
NOTE: Not recommended for operation beyond printedH-Q curve.NOTA: No se recomienda para funcionamiento superioral impreso en la curva H-Q.
METERSMETROS
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
Model 3CC13MS / Size (Tamaño) 3 x 4 – 131750 RPM Curve (Curva) CN0112R00
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 131⁄16" C 125⁄16
E 11¾ 1¼"
G 10¾
J 91⁄8 L 8
NOTE: Pump will pass a sphere to 3⁄8" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 3⁄8 de pulgada de diámetro.
10
0
8003002001000
110
0
6'
180
% EFF
m3/hr
U.S. GPM
70
60
30
15
400 500 600 700
40 80 160140120100
90
10
60
6020
25
20
100
80
50
40
30
20 10 HP
5
5070 75 78
80
80
8'
10'
7578
70
12'
15'
60
50
5 HP 7 1∨2 HP
15 HP
A 101/16" DIA.
B 93/4"
C 9"
D 85/8"
E 81/8"
F 75/8"
NPSHR – FEET (PIES)
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamientosuperior al impreso en la curva H-Q.
METERSMETROS
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
Model 3CC10MS / Size (Tamaño) 3 x 4 – 101750 RPM Curve (Curva) CN0096R00
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 101⁄16" 11⁄4" B 93⁄4 C 9 D 85⁄8 E 81⁄8
7⁄8"
F 75⁄8
NOTE: Pump will pass a sphere to 1⁄2" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 1⁄2 de pulgada de diámetro.
Performance Curves, Curvas de desempeño
Goulds PumpsAg. / Irrigation
27
15
0
8005004504000
15
65
5
6'
180 m3/hr
U.S. GPM
60
20
70
20
600 650 700 750
20 60 160140120100
30
10
40
50
55
55035030025020015010050
60
10 HP
45
35
25
8040
70 75
75
70
60
78
78
80
80 82
82
8'
10'
11'
12'
7 1/2 HP
5 HP
3 HP
50% EFF
A 77/8" DIA.
C 71/2"
D 71/4"
F 63/4"
G 61/2"
J 53/4"
NPSHR – FEET (PIES)
NOTE: Not recommended for operation beyond printedH-Q curve.NOTA: No se recomienda para funcionamiento superior al impresoen la curva H-Q.
METERSMETROS
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
Model 4CC8MS / Size (Tamaño) 4 x 5 – 81750 RPM
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 77⁄8" C 6½
D 7¼ 7⁄8" F 6¾ G 6½ J 5¾ 1¼"
NOTE: Pump will pass a sphere to 5⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄16 de pulgada de diámetro.
Performance Curves, Curvas de desempeño
0
1501005000
10
0
4CC5MS / Size (Tamaño) 4 x 4-5RPM 1725 Curve (Curva) CN667R00
m3∨hr
U.S. GPM200
70
350
30 40
4
12
10
20
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INAM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
NOTE: Not recommended for operation beyond printedH-Q curve.NOTA: No se recomienda para funcionamiento superior alimpreso en la curva H-Q.
250 300
14
6050
2
4
6
8
3
2
1 1/2 HP
3/4 HP
60% EFF 64 70 72
72
70
64
60
3'NPSHR – FEET (PIES) 4'
6'
8'10'B 45/8"
A 413/16" DIA.
C 41/2"
D 43/16"E 4"
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 413⁄16" B 45⁄8 C 41⁄2
7⁄8" D 43⁄16
E 4
NOTE: Pump will pass a sphere to 5⁄32" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄32 de pulgada de diámetro.
1750 R
PM
28
00
0
0
m3∨hr50 150100 200
10
20
30
50
60
250
40
U.S. GPM
20
200 400
200
80
60
40
1200600 800 1000
180
160
140
120
100
7680
84
82
6'10'K 131/16'' DIA.
Q 93/8''
8'
12'
82
80
L 121/2''
M 1111/16''
N 111/16''
P 101/4''
76
Model 4CC13MS / Size (Tamaño) 4 x 6 – 131750 RPM Curve (Curva) CN0698R00
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamiento superioral impreso en la curva H-Q.
METERSMETROS
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
NPSHR – FEET (PIES)
15 HP
20 HP
25 HP
30 HP
40 HP
50 HP
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
K 131⁄16" L 121⁄2 M 1111⁄16 11⁄4" N 111⁄16
P 101⁄4 Q 93⁄8
NOTE: Pump will pass a sphere to 7⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 7⁄16 de pulgada de diámetro.
Performance Curves, Curvas de desempeño
Goulds PumpsAg. / Irrigation
0
30
60
70
50
40
0
0
8000
m3∨hr250
600400
50 150
200 1000
80
90
1200
100 200
100
110
10
15
20
30
35
300
25
U.S. GPM
L 99/16''
M 81/8''
10 HP
15 HP
20 HP
75
80
14'
82
83
10'
838280
7570
8'
60K 101/16'' DIA.
Model 4CC10MS / Size (Tamaño) 4 x 6 – 101750 RPM Curve (Curva) CN0720R00
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamiento superioral impreso en la curva H-Q.METERS
METROSFEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
NPSHR – FEET (PIES)
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
K 101⁄16" L 99⁄16 11⁄4" M 81⁄8
NOTE: Pump will pass a sphere to 7⁄16" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 7⁄16 de pulgada de diámetro.
29
m3/ hr
NOTE: Not recommended for operation beyond printedH-Q curve.NOTA: No se recomienda para funcionamiento superior alimpreso en la curva H-Q.
METERSMETROS
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
Model 4CC16MS / Size (Tamaño) 4 x 6 – 161780 RPM Curve (Curva) CN0447R01
0
100
0 U.S. GPM
200
250
50
1000
350
1200 1400
60
50
40
30
20
10
0
0 100 200 300 400 500 600 700 800 900
150
600 800400200
300
70
60 HP
75 HP
100 HP
A 16" DIA.
B 155/8"
D 141/2"
E 133/4"
C 153/16"
60% EFF.65
70 7374
7473
5' NPSHR – FEET (PIES)
6'
8'
10'
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 16" B 155⁄8
C 153⁄16 15⁄8" D 14½ E 13¾
NOTE: Pump will pass a sphere to 5⁄8" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄8 de pulgada de diámetro.
Performance Curves, Curvas de desempeño
0
15010050000
5CC6MS / Size (Tamaño) 5 x 5-6RPM 1725 Curve (Curva) CN671R00
m3∨hr
U.S. GPM200
100
500
25
5
18
16
14
12
10
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INAM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
NOTE: Not recommended for operation beyond printedH-Q curve.NOTA: No se recomienda para funcionamiento superior alimpreso en la curva H-Q.
250 300 350 400 450
7550
8
6
4
2
4
3
2
1
C 5" x 37/8"
B 55/16" x 45/16"
D 5" x 39/16"
E 5" x 31/32"
NPSHR – FEET (PIES)7'8'
9'
50% EFF 6065
70
68
68 70
65
1 HP
11∨2 HP
A 51/2" x 41/2" DIA.
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 51⁄2" x x 41⁄2" B 55⁄16 x 45⁄16
C 5 x 37⁄8 7⁄8" D 5 x 39⁄16 E 5 x 31⁄32
NOTE: Pump will pass a sphere to 5⁄32" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄32 de pulgada de diámetro.
1750 R
PM
30
Performance Curves, Curvas de desempeño
Goulds PumpsAg. / Irrigation
00
30
0
30000
m3∨hr
U.S. GPM
100 600
100
10
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
50
40
30
20
10
60
70
80
90
500 1000 1500 2000 2500
200 300 400 500
0
5
10
0
10
40
NPSH
IN F
EET
(NPS
H PIE
S)
NPSH
IN M
ETER
S (N
PSH
MET
ROS)
5
15
20
25
30
20
60 65% EFF
70A 91/2'' DIA.
B 9
C 81/2
D 8
7580
83
E 71/2
15 HP20 HP
25 HP
30 HP
NPSH REQ
8385
80
75
70
40 HP
Model 6CC91/2MS / Size (Tamaño) 6 x 8 – 91/2
1770 RPM Curve (Curva)NOTE: Not recommended for operationbeyond printed H-Q curve.NOTA: No se recomienda la operación más alláde la curva impresa de H-Q (carga-capacidad).
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 9½" B 9 C 8½ 7⁄8" D 8
E 7½
NOTE: Pump will pass a sphere to 5⁄32" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 5⁄32 de pulgada de diámetro.
00
14
0
12006004002000
m3∨hr
U.S. GPM
50 250
10
METERSMETROS
FEETPIES
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
CAPACITY (CAPACIDAD)
50
800 1000
20
12
100 200
0
10
0
20
30
NPSH
IN F
EET
(NPS
H PIE
S)
NPSH
IN M
ETER
S (N
PSH
MET
ROS)
40
8
6
4
5
150
10
30
210
80
% EFF60A 7'' DIA.
B 61/2
C 6
D 51/2
84
70 75
NPSH REQ
84
78
8078
75
70
71/2 HP
3 HP
5 HP
Model 5CC7MS / Size (Tamaño) 5 x 6 – 71750 RPM Curve (Curva)
NOTE: Not recommended for operationbeyond printed H-Q curve.NOTA: No se recomienda la operación más alláde la curva impresa de H-Q (carga-capacidad).
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
A 7" B 6½ 1¼" C 6
D 5½
NOTE: Pump will pass a sphere to 1⁄2" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 1⁄2 de pulgada de diámetro.
31
Performance Curves, Curvas de desempeño
m3∨hr
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamiento superioral impreso en la curva H-Q.
METERSMETROS
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
0
100
0 U.S. GPM600
125
175
50
200 400
150
800 12001000
250
75
25
1400 1600 1800 2000 2200
200
0
10
20
30
40
50
60
70
0 10050 150 200 250 300 350 400 450 500
Model 6CC13MS / Size (Tamaño) 6 x 8 – 13RPM 1780 Curve (Curva) CN0697R00
60 HP
50 HP
40 HP30 HP
75 HP
60% EFF. 7074 78
8482
85
8584
82
U 13" DIA.
M&W 115/8"
N&X 107/8"
Q&Z 10"
4' NPSHR – FEET (PIES)
5'7'
9'
11'
V 125/16"
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
U 13" V 125⁄16
W 115⁄8 15⁄8" X 107⁄8 Z 10 M 115⁄8 N 107⁄8 11⁄4" Q 10
NOTE: Pump will pass a sphere to 7⁄8" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 7⁄8 de pulgada de diámetro.
0
40
60
0
0
0
m3∨hr400200
500 1000
80
3000
100 300
100
180
10
20
40
50
1100
30
U.S. GPM
20
120
140
160
500040001500 2000 2500 3500 4500
1000500 600 700 800 900
11'64 7075 78
8084
84
80
14'17'
20'
24'
Model 8CC13MS / Size (Tamaño) 8 x 10 – 13RPM 1750 Curve (Curva) CN0707R00
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamiento superioral impreso en la curva H-Q.
METERSMETROS
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
NPSHR – FEET (PIES)
150 HP
125 HP
100 HP
75 HP
60 HP
U 13'' DIA.
W 1115/16''
X 107/8''
Y 913/16''
Optional ImpellerImpulsor optativo
Ordering Code Dia. Shaft Dia. Código de pedido Diá. Shaft Dia.
U 13" W 1115⁄16 15⁄8" X 107⁄8
Y 913⁄16
NOTE: Pump will pass a sphere to 7⁄8" diameter.
NOTA: La bomba dejará pasar una esfera de hasta 7⁄8 de pulgada de diámetro.
1750 R
PM
32
NPS
HR –
FEE
T (P
IES)
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamientosuperior al impreso en la curva H-Q.FEET
PIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
Model 11/2SAE10MS Variable SpeedSize (Tamaño) 11/2 x 2 – 10 (Velocidad variable)101/16 Dia. Impeller (Diá. Impulsor) Curve (Curva) CN0733R00
0
100
750U.S. GPM
25 10050 125 150 175 200
200
300
400
30
20
10
0
2400 RPM
2200 RPM
2000 RPM
1800 RPM
5 HP
10 HP
30% EFF.35
40
45
50
45
1600 RPM
Performance Curves, Curvas de desempeño
Goulds PumpsAg. / Irrigation
0
0
1401201000
400
0
50 m3/hr
U.S. GPM
300
100
150
450
50
200
160
10 20 4030
350
250
15050
NOTE: Not recommended for operationbeyond printed H-Q curve.NOTA: No se recomienda para funcionamientosuperior al impreso en la curva H-Q.METERS
METROSFEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
25
75
125
100
180 200 220 24080604020
15 HP
7.5 HP
20 HP
25 HP
30 HP
10 HP
5 HP
30% EFF 40 50 55
57.6
55
Model 11/2SAE91/2MS Variable SpeedSize (Tamaño) 11/2 x 11/2 – 91/2 (Velocidad variable)101/16 Dia. Impeller (Diá. Impulsor) Curve (Curva)
2400 RPM
2200 RPM2000 RPM1800 RPM1600 RPM
2600 RPM
2800 RPM
3000 RPM
3200 RPM
3400 RPM
3600 RPM
33
Performance Curves, Curvas de desempeño
NPS
HR –
FEE
T (P
IES)
NOTE: Not recommended for operationbeyond printed H-Q curve.NOTA: No se recomienda para funcionamientosuperior al impreso en la curva H-Q.
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
Model 21/2SAE9MS Variable SpeedSize (Tamaño) 21/2 x 3 – 9 (Velocidad variable)101/16 Dia. Impeller (Diá. Impulsor) Curve (Curva) CN0735R00
0
100
0 U.S. GPM100 400 500 600 700
200
250
300
3020100
150
50
200 300
400
350
2400 RPM
2200 RPM
2000 RPM
1800 RPM
1600 RPM
10 HP
15 HP
20 HP
66
66
70
60
60% EFF.
NPS
HR –
FEE
T (P
IES)
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamientosuperior al impreso en la curva H-Q.
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
Model 21/2SAE8MS Variable SpeedSize (Tamaño) 21/2 x 3 – 8 (Velocidad variable)715/16 Dia. Impeller (Diá. Impulsor) Curve (Curva) CN0734R00
0
100
0 U.S. GPM50 100 300 350 400 450
200
250 30
20
10
0
150
50
150 200 250
2400 RPM
2200 RPM
2000 RPM
5 HP
10 HP
50% EFF.60
6570
75
1800 RPM
3 HP
7.5 HP1600 RPM
Variab
le Sp
eed
34
NPS
HR –
FEE
T (P
IES)
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamientosuperior al impreso en la curva H-Q.
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
Model 21/2SAE13MS Variable SpeedSize (Tamaño) 21/2 x 3 – 13 (Velocidad variable)131/16 Dia. Impeller (Diá. Impulsor) Curve (Curva) CN0737R00
400
0
100
0 U.S. GPM100 500 600 700
200
250
350
3020100
150
50
200 300 400
300
15 HP
20 HP
25 HP
30 HP
40 HP
50
60
63
65
63
6050% EFF.
1600 RPM
1800 RPM
2000 RPM
2200 RPM
2400 RPM
50 HP
Performance Curves, Curvas de desempeño
Goulds PumpsAg. / Irrigation
NPS
HR –
FEE
T (P
IES)
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamientosuperior al impreso en la curva H-Q.FEET
PIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
Model 21/2SAE10MS Variable SpeedSize (Tamaño) 21/2 x 3 – 10 (Velocidad variable)101/16 Dia. Impeller (Diá. Impulsor) Curve (Curva) CN0736R00
0
100
0 U.S. GPM100 500 600 700 800
200
250
350
3020100
150
50
200 300 400
300
2400 RPM
2200 RPM
2000 RPM
1800 RPM
60% EFF.
65
65
68
60
10 HP
15 HP
20 HP
25 HP
1600 RPM
35
Performance Curves, Curvas de desempeño
NPS
HR –
FEE
T (P
IES)
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamiento superioral impreso en la curva H-Q.
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
0
100
0U.S. GPM
100 500 600 700 1400
200
250
350
30
20
10
0
150
50
200 300 400
300
800 900 1300120011001000
400
Model 3SAE10MS Variable SpeedSize (Tamaño) 3 x 4 – 10 (Velocidad variable)91/8 Dia. Impeller (Diá. Impulsor) Curve (Curva) CN0739R00
2200 RPM
2000 RPM
1800 RPM
1600 RPM
2400 RPM
60% EFF. 7075 78
7880
75
7060
30 HP10 HP
15 HP
20 HP
NPS
HR –
FEE
T (P
IES)
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamiento superioral impreso en la curva H-Q.
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
0
100
0 U.S. GPM100 500 600 700 900
200
250 3020
10
0
150
50
200 300 400
300
800
Model 3SAE10MS Variable SpeedSize (Tamaño) 3 x 4 – 8 (Velocidad variable)81/16 Dia. Impeller (Diá. Impulsor) Curve (Curva) CN0738R00
10 HP
15 HP
20 HP
7.5 HP
2400 RPM
2200 RPM
2000 RPM
1800 RPM
58% EFF.68
73 76
6873
58
5 HP
1600 RPM Variab
le Sp
eed
36
NPS
HR –
FEE
T (P
IES)
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamiento superioral impreso en la curva H-Q.
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
0
100
0 U.S. GPM600 1600
200
250 30
20
10
0
150
50
200 400 800 140012001000
Model 4SAE8MS Variable SpeedSize (Tamaño) 4 x 5 – 8 (Velocidad variable)77/8 Dia. Impeller (Diá. Impulsor) Curve (Curva) CN0741R00
2200 RPM
2000 RPM
1800 RPM
2400 RPM
1600 RPM
50% EFF.60
7075
82
80
80
75
70
71∨2 HP
10 HP
15 HP
20 HP
25 HP
Performance Curves, Curvas de desempeño
Goulds PumpsAg. / Irrigation
NPS
HR –
FEE
T (P
IES)
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamientosuperior al impreso en la curva H-Q.
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
0
100
0U.S. GPM
600 1400
50
200 400
150
800 12001000
500
200
250
450
400
350
300
30
100 300 500 700 900 13001100
01020
Model 3SAE13MS Variable SpeedSize (Tamaño) 3 x 4 – 13 (Velocidad variable)131/16" Dia. Impeller (Diá. Impulsor) Curve (Curva) CN0740R00
30 HP
100 HP120 HP
20 HP
40 HP
50 HP
60 HP
75 HP
60% EFF.70 75
78
75
70
60
50
2200 RPM
2000 RPM
2400 RPM
1800 RPM
1600 RPM
2600 RPM
37
Performance Curves, Curvas de desempeño
NPS
HR –
FEE
T (P
IES)
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamientosuperior al impreso en la curva H-Q.
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
0
100
0U.S. GPM
600 2200
50
200 400
150
800 12001000
400
1400 1600
200
250
350
300
30
010
20
Model 4SAE13MS Variable SpeedSize (Tamaño) 4 x 6 – 13 (Velocidad variable)131/16" Dia. Impeller (Diá. Impulsor) Curve (Curva) CN0743R00
1800 2000
2000 RPM
1800 RPM
2200 RPM
1600 RPM
60% EFF.78
72
82
78
60
82
40 HP
100 HP
125 HP
50 HP
60 HP75 HP
2400 RPM
FEETPIES
NPS
HR –
FEE
T (P
IES)
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamiento superioral impreso en la curva H-Q.
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
0
100
0 U.S. GPM600 1600
200 3020100
50
200 400 800 140012001000
175
150
125
75
25
Model 4SAE10MS Variable SpeedSize (Tamaño) 4 x 6 – 10 (Velocidad variable)101/16 Dia. Impeller (Diá. Impulsor) Curve (Curva) CN0742R00
2200 RPM
2000 RPM
1800 RPM
1600 RPM
60% EFF.
7580
83
80
75
40 HP30 HP
15 HP
20 HP
50 HP
Variab
le Sp
eed
38
Performance Curves, Curvas de desempeño
Goulds PumpsAg. / Irrigation
NPS
HR –
FEE
T (P
IES)
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamiento superioral impreso en la curva H-Q.
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
0
100
0U.S. GPM
600 1600200 400 800 12001000
700
1400
200
400
300
0
10
15
600
500
5
Model 4SAE16MS Variable SpeedSize (Tamaño) 4 x 6 – 16 (Velocidad variable)16" Dia. Impeller (Diá. Impulsor) Curve (Curva) CN0746R00
60% EFF. 6570 73
74
73
2200 RPM
1800 RPM
1600 RPM
2000 RPM
75 HP
100 HP
125 HP
50 HP
150 HP
175 HP
0
0
1400120010000
80
0
500 m3/hr
U.S. GPM
60
20
30
90
10
40
1600
100 200 400300
70
50
3010
NOTE: Not recommended for operationbeyond printed H-Q curve.NOTA: No se recomienda para funcionamientosuperior al impreso en la curva H-Q.METERS
METROSFEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
20
1800 2000 2200 2400800600400200
15 HP
20 HP
25 HP30 HP
60% EFF 70 7580
83
5
15
25
40 HP
75
80
83
85
Model 6SAE91/2MS Variable SpeedSize (Tamaño) 6 x 8 – 91/2 (Velocidad variable)101/16 Dia. Impeller (Diá. Impulsor) Curve (Curva)
1800 RPM
1600 RPM
1400 RPM
1200 RPM
1000 RPM
39
Performance Curves, Curvas de desempeño
NPS
HR –
FEE
T (P
IES)
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamiento superioral impreso en la curva H-Q.
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
0
100
0U.S. GPM
600 3200
50
200 400
150
800 12001000
550
1400 1600 1800 2000 2200
200
250
500
450
400
350
300
2400 300028002600
3020100
Model 6SAE13MS Variable SpeedSize (Tamaño) 6 x 8 – 13 (Velocidad variable)13" Dia. Impeller (Diá. Impulsor) Curve (Curva) CN0744R00
75 HP
100 HP
125 HP
150 HP
200 HP
250 HP
2600 RPM
2200 RPM
2000 RPM
2400 RPM
1800 RPM
60% EFF.70 75 82
8485
84
82
1600 RPM
Variab
le Sp
eed
NPS
HR –
FEE
T (P
IES)
NOTE: Not recommended for operation beyondprinted H-Q curve.NOTA: No se recomienda para funcionamiento superioral impreso en la curva H-Q.
FEETPIES
CAPACITY (CAPACIDAD)
TOTA
L DY
NAM
IC H
EAD
(CAR
GA D
INÁM
ICA
TOTA
L)
0
100
0U.S. GPM
6000
50
500
150
1000
350
1500 2000 2500 3000 3500
200
250
325
300
4000 550050004500
3020100
25
75
125
175
225
275
Model 8SAE13MS Variable SpeedSize (Tamaño) 8 x 10 – 13 (Velocidad variable)13" Dia. Impeller (Diá. Impulsor) Curve (Curva) CN0745R00
75 HP
100 HP
300 HP
150 HP
200 HP
250 HP
350 HP
2400 RPM
2000 RPM
1800 RPM
2200 RPM
1600 RPM
60% EFF.
7080
8586
85
80
40
Materials of ConstructionMateriales de Construcción
Seal DesignDiseño del sello
23
26
24
MECHANICAL SEAL ASSEMBLY, INSTALACIÓN DEL SELLO MECÁNICO
PRIME SAFE SEAL ARRANGEMENT, ACCESORIO PRIME SAFE DEL SELLO
7
8
9
3 5
4 2 1
6 Location, Description, Ubicación Descripción 1 Stationary Face, Cara estacionaria
2 Rotating Face, Cara rotativa
3 Spring – 316SS, Resorte – 316SS
4 Bellows (Elastomer),
Fuelle (Elastómero)
5 Retainer – 316SS,
Dispositivo de retención – 316SS
6 Cup (Elastomer), Cubeta (Elastómero)
Location, Description, Ubicación Descripción Grease Feeder – shown, Canal de alimentación de grasa – aparece en el gráfico 7 Oiler – not shown (for 18BZ, 19BZ and 20BZ only), Engrasador – no aparece en el gráfico (únicamente para 18BZ, 19BZ y 20BZ)
8 Lip Seal – BUNA,
Sello con reborde – BUNA
9 Gland – Aluminum,
Casquillo – Aluminio
Mechanical Seal (seal code 8A or 8B), – Sello mecánico (código del sello 8A o 8B)
7⁄8" Impeller Bore 11⁄4" Impeller Bore 15⁄8" Impeller Bore and 11⁄4" Seal Bore and 15⁄8" Seal Bore, and 2" Seal Bore, Seal Code, Rotary, Stationary, Elastomers, Metal Parts, Diámetro interior, Diámetro interior, Diámetro interior, Código del sello Rotativo Estacionario Elastómeros Partes metálicas del impulsor 7⁄8" del impulsor 11⁄4" del impulsor 15⁄8" y diámetro interior y diámetro interior y diámetro interior del sello 11⁄4" del sello 15⁄8" del sello 2" 0 Ceramic, Cerámica BUNA-N 10K13 10K16 10K84 1 Carbon, Carbono EPR 10K19 10K20 NA 3
316SS 10K27 10K45 10K112
5 Sil-Carb., Viton
10K64 10K65 8A* Sil-Carb., Carburo de silicona NA NA 10K144 8B** Carburo de silicona 10K64 10K65 9† Packed Box with BUNA O-Ring, Caja prensaestopas con junta tórica de BUNA 15K17 15K3 15K4
* Prime Safe option with oiler, Opción Prime Safe con engrasador** Prime Safe option with grease, Opción Prime Safe con grasa† Not available for 51, 52, 53, 54, 55 (BZ, FE) sizes., No disponible para 51, 52, 53, 54, 55 (BZ, FE) tallas.
Goulds PumpsAg. / Irrigation
41
Close-Coupled Materials of Construction, Materiales de construcción del acoplamiento corto
NOTE:Pumps will be shipped with top-vertical discharge position as standard. For other orientations, remove casing bolts – rotate discharge to desired position – replace and tighten bolts to 25 ft./lbs. Note that discharge may extend below motor mounting surface in bottom-horizontal position; adequate clearance must be provided.
NOTA:Las bombas salen de la fábrica con la des-carga orientada en posición vertical superior de manera estándar. Para modificar la orien-tación, retirar los pernos de la carcasa, hacer girar la descarga hasta la posición deseada y volver a colocar los pernos, ajustándolos a una torsión de 25 pies/libras. Se ha de notar que la descarga se puede extender por debajo de la superficie de montaje del motor en la posición horizontal inferior; por lo tanto, debe proveerse suficiente espacio.
For separate seal housing and adapter construction, all bronze material only, see repair parts page.
Para la construcción separada del compartimiento del sello y el adaptador, materiales de bronce únicamente, consul-te la página de piezas de repuesto.
1
AISI 1045 steel motor shaft exten-sion (typical)Extensión del eje del motor de acero AISI 1045 (típico)
101
103
383
178
126
198
199
370408
513 108
371
100
Back wearing ring on 2½ x 3 – 7 onlyAnillo de desgaste posterior en el21⁄2 x 3 – 7 únicamente.
1001
1
Item No. Description Materials, Materiales No. Ítem Descripción All Iron Bronze Fitted All Bronze Todo hierro Accesorios de bronce Todo bronce 100 Casing, Carcasa 1001 101 Impeller, Impulsor 1101
1101
103 Casing wear ring, 1618 1618 Anillo de desgaste de la carcasa 108 Adapter, Adaptador 1001 1001 184 Seal housing, Cubierta del sello One piece with adapter, Una pieza con adaptador 1101 126 Shaft sleeve, Camisa del eje 178 Impeller key, Chaveta del impulsor 198 Impeller bolt, Perno del impulsor 199 Impeller washer, Arandela del impulsor 370 Hex head cap screw (adapter to case), Tornillo de cabeza hexagonal (del adaptador a la cubierta) Steel SAE 1200 Grade 5 371 Hex head cap screw (adapter to motor), Tornillo de Acero SAE 1200 grado 5 cabeza hexagonal (del adaptador al motor) 383 Mechanical seal, Sello mecánico See seal chart on page 39, Ver tabla del sello página 39 408 Pipe plug 1⁄4" or 3⁄8", Tapón de tubos de 1⁄4 de pulgada ó 3⁄8 de pulgada Steel, Acero Bronze, Bronce 513 O-ring, Anillo en O BUNA-N, BUNA-N Material Code, Código de material Engineering Standard, Norma de ingeniería 1101 Cast iron ASTM A48 CL20, Hierro fundido ASTM A48 CL20 1101 Silicon bronze ASTM B584, C87500, Siliciuro de bronce ASTM B584, C87500 1618 Bizmuth brass, Latón al bismuto
AISI Type 300 series stainless steelAcero inoxidable serie AISI tipo 300
Packed Box Arrangement, Caja prensaestopas Item No., No. Ítem Description, Descripción Materials, Materiales 105 Lantern ring, Aro de linterna TeflonTM
106 Packing, 5 rings; Empaquetadura, 5 aros Teflon Impregnated, Impregnado de Teflon 107 Gland, Casquillo AISI 316SS 126 Shaft sleeve, Camisa del eje 353 Gland stud, Perno del casquillo 355 Gland nut, Tuerca del casquillo
105 106 107
353
126
355
Packed Box ArrangementCaja prensaestopas
AISI Type 300 Series Stainless SteelAcero inoxidable serie AISI tipo 300
AG-FLO Sizes, Tamaños de AG-FLO1CC7 – 1 x 2-71CC8 – 1 x 2-8
1½CC6H – 1½ x 2-6 (H)1½CC8 – 1½ x 2-82½CC7 – 2½ x 3-7
2CC7 – 3 x 4-72CC7 – 2 x 2½-72CC5 – 2 x 2-5
2½CC5 – 2½ x 2½-53CC5 – 3 x 3-54CC5 – 4 x 4-55CC6 – 5 x 5-65CC7 – 5 x 6-7
42
101
178
198
199
126
103
383
408
370 371
100 513 108
ANSI 1045 steel motorshaft extension (typical)
ANSI 1045 Extensión del ejedel motor de acero (típica)
Close-Coupled Materials of ConstructionMateriales de construcción del acoplamiento corto
NOTE:Seal housing wear ring (item number 203) not shown. See repair parts page for detail. (Required for all models except 3 x 4 – 10.)
Material Code Engineering Standard Código de material Norma de ingeniería 1003 Cast iron ASTM A48 CL30 Hierro fundido ASTM A48 CL20 1618 Bismuth Bronze – Lead Free, Bismuth Bronze – Lead Free 1001 Cast iron ASTM A48 CL20 Hierro fundido ASTM A48 CL20 1101 ASTM B584, Modified C87500 – Lead Free ASTM B584, modified C87500 – Lead Free Packed Box Arrangement, Caja prensaestopas Item No. Description Materials No. Ítem Descripción Materiales 105 Lantern ring TeflonTM
Aro de linterna 106 Packing, 5 rings Teflon Impregnated Empaquetadura, 5 aros Impregnado de Teflon 107 Gland, Casquillo AISI 316SS 126 Shaft sleeve Camisa del eje 353 Gland stud AISI Type 300 Series Stainless Steel Perno del casquillo Acero inoxidable serie AISI tipo 300 355 Gland nut Tuerca del casquillo
Item No. Description Materials, Materiales No. Descripción All Iron Bronze Fitted Ítem Todo Accesorios hierro de bronce 100 Casing, Carcasa 1003
101 Impeller, Impulsor 1101
103 Casing wear ring, Anillo de desgaste de 1618 la carcasa
108 Adapter/seal housing, Adaptador/ 1001 Cubierta del sello
126 Shaft sleeve, Camisa del eje
178 Impeller key, Chaveta del impulsor
198 Impeller bolt, Tornillo del impulsor
199 Impeller washer, Arandela del impulsor
370 Hex head cap screw (adapter to case), Tornillo de cabeza hexagonal (del adaptador a la cubierta) Steel Zinc Platted Grade 5 371 Hex head cap screw (adapter to motor), Acero SAE 1200 grado 5 Tornillo de cabeza hexagonal (del adaptador al motor) 383 Mechanical seal, Sello mecánico See seal chart, Ver tabla del sello
408 Pipe plug 1⁄4" or 3⁄8", Tapón de tubos de Zinc Platted Steel 1⁄4 de pulgada ó 3⁄8 de pulgada Zinc Platted Steel
513 O-ring, Anillo en O BUNA-N – Standard, EPR – Optional Viton – Optional
1001
AISI Type 300 Series SSAcero inoxidable serie
AISI tipo 300
NOTA: El anillo de desgaste del compartimiento de sello (ítem número 203) no se muestra. Consulte la página de piezas de repuesto para mayor detalle. (Se requiere para todos los modelos con excepción del 3 x 4 – 10).
105 106 107
353
126
355
Packed Box ArrangementCaja prensaestopas
108
AG-FLO Sizes, Tamaños de AG-FLO
1¼CC9½ – 1¼ x 1½-9½6CC9½ – 6 x 8-9½2½CC8 – 2½ x 3-8
3CC8 – 3 x 4-84CC8 – 4 x 5-8
12CC10 – 1½ x 2-102½CC10 – 2½ x 3-10
3CC10 – 3 x 4-102½CC10 – 2½ x 3-10
4CC10 – 4 x 6-102½CC13 – 2½ x 3-13
3CC13 – 3 x 4-134CC13 – 4 x 6-13
AG-FLO Sizes, Tamaños de AG-FLO6CC13 – 6 x 8-13
8CC13 – 8 x 10-134CC16 – 4 x 6-16
Goulds PumpsAg. / Irrigation
43
Power Frame Materials of ConstructionMateriales de construcción del cuadro de fuerza
NOTE:Above shows typical AI or BF construction. For separate seal housing adapter, all bronze construction, see repair parts.
Pumps will be shipped with top-vertical discharge position as standard. For other orientations, remove casing bolts – rotate discharge to desired position – replace and tighten bolts to 25 ft./lbs. Note that discharge may extend below motor mounting surface in bottom-horizontal position; adequate clearance must be provided.NOTA:Esta información corresponde a las construccio-nes típicas AI y BF. Para el adaptador separado del compartimiento de sellos y construcción en todo bronce, consulte las partes de repuesto.
Las bombas salen de la fábrica con la descarga orientada en posición vertical superior de manera estándar. Para modificar la orientación, retirar los pernos de la carcasa, hacer girar la descarga hasta la posición deseada y volver a colocar los pernos, ajustándolos a una torsión de 25 pies/libras. Se ha de notar que la descarga se puede extender por debajo de la superficie de montaje del motor en la posición horizontal inferior; por lo tanto, debe proveerse suficiente espacio.
Item No. Description Materials, Materiales No. Ítem Descripción All Iron Bronze Fitted All Bronze Todo hierro Accesorios de bronce Todo bronce 100 Casing, Carcasa 1001 101 Impeller, Impulsor 1101 103 Casing wear ring, Anillo de desgaste de la carcasa 108 Adapter, Adaptador 1001 1001 184 Seal housing, Cubierta del sello One piece with adapter, Una pieza con adaptador 1101 112 Ball bearing (outboard), Cojinete de bolas (exterior) Steel, Acero 122 Shaft, Eje Carbon steel, Acero al carbono 123 V-ring (Deflector), Anillo en V (Deflector) BUNA-N 126 Shaft sleeve, Camisa del eje AISI Type 303 SS, Acero inoxidable AISI tipo 303 134 Bearing cover, Cubierta del cojinete 1001 168 Ball bearing (inboard), Cojinete de bolas (interior) Steel, Acero 178 Impeller key, Chaveta del impulsor 198 Impeller screw, Tornillo del impulsor 199 Impeller washer, Arandela del impulsor 228 Bearing frame, Marco de cojinete 1001 333A Lip seal, Sello con reborde 370 Hex head cap screw (adapter to case), Tornillo de cabeza hexagonal (del adaptador a la cubierta) 370B Hex head cap screw (adapter to bearing frame),Tornillo de cabeza hexagonal (del adaptador al marco de cojinetes) Steel SAE 1200 Grade 5 370C Hex head cap screw (bearing cover to frame),Tornillo de Acero SAE 1200 grado 5 cabeza hexagonal (de la cubierta de cojinetes al marco) 382 Retaining ring, Anillo de retención 383 Mechanical seal, Sello mecánico See seal chart, Ver tabla del sello 408 Pipe plug 1⁄4" or 3⁄8", Tapón de tubos de 1⁄4 de pulgada ó 3⁄8 de pulgada Steel, Acero Bronze, Bronce 513 O-ring, Anillo en O BUNA-N, BUNA-N Material Code, Código de material Engineering Standard, Norma de ingeniería 1101 Cast iron ASTM A48 CL20, Hierro fundido ASTM A48 CL20 1101 Silicon bronze ASTM B584, C87500, Siliciuro de bronce ASTM B584, C87500 1618 Bizmuth brass, Latón al bismuto
AISI Type 303 Series SSAcero inoxidable serie AISI tipo 300
100
178
198
101
199
103
126
383
408 370 123
382
333A
134
112122228168108513 370C
370B
Packed Box Arrangement, Caja prensaestopas Item No., No. Ítem Description, Descripción Materials, Materiales 105 Lantern ring, Aro de linterna TeflonTM
106 Packing, 5 rings; Empaquetadura, 5 aros Teflon Impregnated, Impregnado de Teflon 107 Gland, Casquillo AISI 316SS 126 Shaft sleeve, Camisa del eje 353 Gland stud, Perno del casquillo 355 Gland nut, Tuerca del casquillo
1618 1618
1101
1001
AISI Type 300 Series Stainless SteelAcero inoxidable serie AISI tipo 300
105 106 107
353
126
355
Packed Box ArrangementCaja prensaestopas
AG-FLO Sizes, Tamaños de AG-FLO1FRM7 – 1 x 2-71FRM8 – 1 x 2-8
1½FRM6 – 1½ x 2-6 (H)1½FRM8 – 1½ x 2-82½FRM7 – 2½ x 3-7
3FRM7 – 3 x 4-72FRM5 – 2 x 2-5
2½FRM5 – 2½ x 2½-53FRM5 – 3 x 3-54FRM5 – 4 x 4-55FRM6 – 5 x 5-6
2FRM7 – 2 x 2½-75FRM7 – 5 x 6-7
44
Power Frame Materials of Construction, Materiales de construcción del cuadro de fuerza
Item No. Description Materials, Materiales No. Descripción All Iron Bronze Fitted Ítem Todo Accesorios hierro de bronce 100 Casing, Carcasa 1003
101 Impeller, Impulsor 1101
103 Casing wear ring, Anillo de desgaste de 1618 la carcasa
108 Adapter/seal housing, Adaptador/ 1001 Cubierta del sello
126 Shaft sleeve, Camisa del eje
178 Impeller key, Chaveta del impulsor
198 Impeller bolt, Tornillo del impulsor
199 Impeller washer, Arandela del impulsor
370 Hex head cap screw (adapter to case),Tornillo de cabeza hexagonal (del adaptador a la cubierta) Steel Zinc Platted Grade 5 370B Hex head cap screw (adapter to bearing frame), Acero Zinc Platted grado 5 Tornillo de cabeza hexagonal (del adaptador al motor) 383 Mechanical seal, Sello mecánico See seal chart, Ver tabla del sello
408 Pipe plug 1⁄4" or 3⁄8", Tapón de tubos de Zinc PlattedSteel, 1⁄4 de pulgada ó 3⁄8 de pulgada Zinc Platted Acero
513 O-ring, Anillo en O BUNA-N – Standard, Standard EPR – Optional, Optional Viton – Optional, Optional
Power End Components, Componentes del extremo de fuerza
228 Bearing frame, Marco de cojinete
134 Bearing cover, Cubierta del cojinete
100
101
178
198
199
103
126
383
408 370 123 370B 193 193
382
333A
134
370C112122228168108513
Item No. Description Materials, Materiales No. Descripción All Iron Bronze Fitted Ítem Todo Accesorios hierro de bronce 122 Pump shaft, Eje de la bomba Steel, Acero
168 Ball bearing (inboard), Cojinete de bolas (interior) Steel, Acero
112 Ball bearing (outboard), Cojinete de bolas (exterior) Steel, Acero
382 Retaining ring, bearing, Anillo de retención, cojinete
370C Hex head cap screw (bearing frame to cover), Tornillo de cabeza hexagonal (de la cubierta de cojinetes al marco)
333A Lip seal, Sello con reborde BUNA-N
193 Grease fitting, Accesorio grasa Steel, Acero
123 V-ring deflector, Anillo en V (Deflector) BUNA-N
Packed Box Arrangement, Caja prensaestopas Item No. Description Materials No. Ítem Descripción Materiales 105 Lantern ring TeflonTM
Aro de linterna 106 Packing, 5 rings Teflon Impregnated Empaquetadura, 5 aros Impregnado de Teflon 107 Gland, Casquillo AISI 316SS 126 Shaft sleeve Camisa del eje 353 Gland stud AISI Type 300 Series Stainless Steel Perno del casquillo Acero inoxidable serie AISI tipo 300 355 Gland nut Tuerca del casquillo Material Code Engineering Standard Código de material Norma de ingeniería 1001 Cast iron ASTM A48 CL20 Hierro fundido ASTM A48 CL20 Sil-Brass ASTM B584, Modified C87500 – 1102 Lead Free Sil-Brass ASTM B584, Modified C87500 – Lead Free 1003 Cast Iron ASTM A48 CL30 Cast Iron ASTM A48 CL30 1618 Bismuth Bronze – Lead Free Bismuth Bronze – Lead Free
1001
AISI Type 300 Series SSAcero inoxidable serie AISI
tipo 300
105 106 107
353
126
355
Packed Box ArrangementCaja prensaestopas
112
L-Group ArrangementArreglo de grupo en L
Cast iron ASTM A48 CL20Hierro fundido ASTM A48 CL20
Steel Zinc PlattedGrade 5,
Acero Zinc Plattedgrado 5
108
AG-FLO Sizes, Tamaños de AG-FLO
2½FRM8 – 2½ x 3-83FRM8 – 3 x 4-84FRM8 – 4 x 5-8
1½FRM10 – 1½ x 2-102½FRM10 – 2½ x 3-10
3FRM10 – 3 x 4-102½FRM10 – 2½ x 3-10
4FRM10 – 4 x 6-10
2½FRM13 – 2½ x 3-133FRM13 – 3 x 4-134FRM13 – 4 x 6-13
AG-FLO Sizes, Tamaños de AG-FLO
6FRM13 – 6 x 8-138FRM13 – 8 x 10-134FRM16 – 4 x 6-16
1¼FRM9½ – 1¼ x 1½-9½6FRM9½ – 6 x 8-9½
Goulds PumpsAg. / Irrigation
45
SAE Drive Materials of ConstructionMateriales de construcción del mando SAE
Item No. Description Materials, Materiales
No. Descripción All Iron Bronze Fitted Ítem Todo Accesorios hierro de bronce
100 Casing, Carcasa 1003
101 Impeller, Impulsor 1101
103 Casing wear ring, Anillo de desgaste de 1618 la carcasa
108 Adapter/seal housing, Adaptador/ 1001 Cubierta del sello
126 Shaft sleeve, Camisa del eje
178 Impeller key, Chaveta del impulsor
198 Impeller nut, Tornillo del impulsor
370 Hex head cap screw (adapter to case),Tornillo de cabeza hexagonal (del adaptador a la cubierta) Steel Zinc Platted Grade 5 370B Hex head cap screw (adapter to bearing frame), Acero Zinc Platted grado 5 Tornillo de cabeza hexagonal (del adaptador al motor) 383 Mechanical seal, Sello mecánico See seal chart, Ver tabla del sello 408 Pipe plug 1⁄4" or 3⁄8", Tapón de tubos de Zinc Platted Steel, 1⁄4 de pulgada ó 3⁄8 de pulgada Zinc Platted Acero
513 O-ring, Anillo en O BUNA-N – Standard, Standard EPR – Optional, Optional Viton – Optional, Optional
Power End Components, Componentes del extremo de fuerza 228 Bearing frame, Marco de cojinete 1003 134 Bearing cover, Cubierta del cojinete 1001 340 Adapter/Engine, Adaptador/Motor 1003 371C Hex head cap screw (adapter to bearing frame) Steel SAE 1200 grade 5 501N Cover/adapter, Cubierta/Adaptador Galvinized steel 327C Cap screw (cover to adapter) Steel SAE 1200 grade 5
Item No. Description Materials, Materiales
No. Descripción All Iron Bronze Fitted Ítem Todo Accesorios hierro de bronce
122 Pump shaft, Eje de la bomba AISI 4140
168 Ball bearing (inboard), Cojinete de bolas (interior) Steel, Acero
112 Ball bearing (outboard), Cojinete de bolas (exterior) Steel, Acero
382 Retaining ring, bearing, Anillo de retención, cojinete
370C Hex head cap screw (bearing frame to cover), Tornillo de cabeza hexagonal (de la cubierta de cojinetes al marco)
333A Lip seal, Sello con reborde BUNA-N
193 Grease fitting, Accesorio grasa Steel, Acero
123 V-ring deflector, Anillo en V (Deflector) BUNA-N
Packed Box Arrangement, Caja prensaestopas Item No. Description Materials No. Ítem Descripción Materiales 105 Lantern ring TeflonTM
Aro de linterna 106 Packing, 5 rings Teflon Impregnated Empaquetadura, 5 aros Impregnado de Teflon 107 Gland, Casquillo AISI 316SS 126 Shaft sleeve Camisa del eje 353 Gland stud AISI Type 300 Series Stainless Steel Perno del casquillo Acero inoxidable serie AISI tipo 300 355 Gland nut Tuerca del casquillo Material Code Engineering Standard Código de material Norma de ingeniería 1001 Cast iron ASTM A48 CL20 Hierro fundido ASTM A48 CL20 1003 Cast iron ASTM A48 CL30 Hierro fundido ASTM A48 CL30 Sil-Brass ASTM B584, Modified C87500 – 1101 Lead Free Sil-Brass ASTM B584, Modified C87500 – Lead Free 1618 Bismuth Bronze – Lead Free, Bismuth Bronze – Lead Free
1001
AISI Type 300 Series SSAcero inoxidable serie AISI
tipo 300
105 106 107
353
126
355
Packed Box ArrangementCaja prensaestopas
100
101
178
198
198
103
122
112
408370
108
370B
168 193134 333A
370C
371C 193228
165126
513 382
501N327C
340
123
333A
Steel SAE 1200Grade 5,
Acero SAE 1200grado 5
108
AG-FLO Sizes, Tamaños de AG-FLOGroup 1, Grupo 1
2½SAE8 – 2½ x 3-83SAE8 – 3 x 4-84SAE8 – 4 x 5-8
1½SAE10 – 1½ x 2-10
2½SAE10 – 2½ x 3-103SAE10 – 3 x 4-10
2½SAE9 – 2½ x 3-94SAE10 – 4 x 6-10
2½SAE13 – 2½ x 3-133SAE13 – 3 x 4-134SAE13 – 4 x 6-13
Keyed Shaft Shown(Spline Shaft Optional)
Group 2, Grupo 26SAE13 – 6 x 8-138SAE13 – 8 x 10-134SAE13 – 4 x 6-13
1¼SAE9½ – 1¼ x 1½-9½6SAE9½ – 6 x 8-9½
46
E1⁄4" NPT
CREFWYDISCHARGE,DESCARGA
SUCTION,SUCCIÓN
P.MAX
F FB H – 4 HOLES,
H – 4 AGUJEROS
LEA
Z RABMAX.
A B CREF D E F G H
143JM 6½ 5¼ 6 11¼ 3½ 2¾ 2 1⁄8
11⁄32 65⁄8 145JM 2½ 182JM
8½ 57⁄8 6½ 15 4½ 3¾ 2¼ 3⁄16 13⁄32 77⁄8
184JM 2¾ 213TCZ 10½ 73⁄8 8 18½ 5¼ 4¼ 2¾ ¼ 13⁄32 95⁄8
P. Max.,P. Máx.
AB Max.,AB Máx.
Motor Frame,Armazón del
Motor
HP @ 3500 RPM HP @ 1750 RPM 1 Phase, Monofásicos 3 Phase, Trifásicos 1 Phase, Monofásicos 3 Phase, Trifásicos ODP TEFC ODP TEFC ODP TEFC ODP TEFC 143JM ¾, 1, 1½ ¾, 1, 1½ ¾, 1, 1½ ¾, 1, 1½ ½, ¾ ½, ¾ ½, ¾, 1 ½, ¾, 1 41 145JM 2 2 2,3 2,3 1 1 1½, 2 1½, 2 57 182JM 3 3 5 3 3 – 3 3 77 184JM 5 3, 5 7½ 5, 7½ 3 – 5 5 97 213TCZ – – 10 10 – – – – 133
Motor Frame,Armazón del
Motor
2CC5 2 x 2 – 5 2 2 315⁄16 215⁄16 15⁄8 41⁄8 5 3 35⁄16 26 10 105⁄8
2½CC5 2½ x 2½ – 5 2½ 2½ 4¾ 3¾ 33⁄8 4¼ 6 3½ 31 101⁄8 10¾
3CC5 3 x 3 – 5 3 3 55⁄16 45⁄16 23⁄16 4½ 3½ 37⁄8 37 107⁄8 11½
DCMax.,
DCMáx.
NOTES:1. Pumps will be shipped with top
vertical discharge as standard. For other orientations, remove casing bolts, rotate to desired position, replace and tighten bolts to 37 lb. – ft.
2. Dimensions are in inches.
3. Motor dimensions may vary with motor manufacturer.
4. Not to be used for construction purposes.
NOTAS:1. Las bombas se transportarán
con la descarga vertical superior como estándar. Para otras ori-entaciones, retirar los tornillos de la carcasa, rotar a la posición deseada, reemplazar y apretar los tornillos 37 libras – pies.
2. Las dimensiones son en pulgadas.
3. Las dimensiones del motor pueden que varíen con los fabricantes.
4. No debe usarse para propósitos de construcción.
G
Suction, Discharge, Succión Descarga
Pump Size,Tamaño
de laBomba
Wt.(lbs.),Peso
(libras)
Dimensions Determined by Motor, Dimensiones Determinadas por el Motor
Horsepowers, FuerzasWt.
(lbs.),Peso
(libras)
Close Coupled Dimensions Determined by Pump, Dimensiones del Acople Cerrado Determinadas por la Bomba
Dimension “L”Motor Frame Size,Tamaño del bastidor
del motor de dimensión “L”
DD R W X Y Z
140 180
DDDCMAX.
D
X
Close-Coulpled Dimensions and Weights Pesos y dimensiones del acoplamiento corto
Identifier Number,Identifier Number
Goulds PumpsAg. / Irrigation
47
A B C D E F G H
143JM 6½ 5¼ 6 11¼ 3½ 2¾ 2 1⁄8
11⁄32 65⁄8 145JM 2½ 182JM
8½ 57⁄8 6½ 15 4½ 3¾ 2¼ 3⁄16 13⁄32 77⁄8
184JM 2¾ 213JM
18½ 2¾ 213TCZ 10½ 73⁄8 8 5¼ 4¼ ¼ 13⁄32 95⁄8 215JM 20 3½
P. Max.,P. Máx.
AB Max.,AB Máx.
Motor Frame,Armazón del
Motor
HP @ 3500 RPM HP @ 1750 RPM 1 Phase, Monofásicos 3 Phase, Trifásicos 1 Phase, Monofásicos 3 Phase, Trifásicos ODP TEFC ODP TEFC ODP TEFC ODP TEFC 143JM ¾, 1, 1½ ¾, 1, 1½ ¾, 1, 1½ ¾, 1, 1½ ½, ¾ ½, ¾ ½,¾, 1 ½, ¾, 1 41 145JM 2 2 2,3 2,3 1 1 1½, 2 1½, 2 57 182JM 3 3 5 3 3 – 3 3 77 184JM 5 3, 5 7½ 5, 7½ 3 – 5 5 97 213JM 7½ – 7½, 10 7½ – – – – 133 213TCZ – 7½ – 7½ – – – – 133 215JM 10 7½, 10 7½, 10, 15 7½, 10, 15 – – – – 154
Motor Frame,Armazón del
Motor
4CC5 4 x 4 – 5 4 6½ 5¼ 4½ 4¼
7 4 4½ 110
113⁄8 12 127⁄8 5CC6 5 x 5 – 6 5 8 6¼ 5 8 5½ 125
* ANSI Class 125 flanges, Bridas ANSI Clase 125
DCMax.,
DCMáx.
NOTES:1. Pumps will be shipped with top
vertical discharge as standard. For other orientations, remove casing bolts, rotate to desired position, replace and tighten bolts to 37 lb. – ft.
2. Dimensions are in inches.
3. Motor dimensions may vary with motor manufacturer.
4. Not to be used for construction purposes.
NOTAS:1. Las bombas se transportarán
con la descarga vertical superior como estándar. Para otras ori-entaciones, retirar los tornillos de la carcasa, rotar a la posición deseada, reemplazar y apretar los tornillos a 37 libras – pies.
2. Las dimensiones son en pulgadas.
3. Las dimensiones del motor pueden que varíen con los fabricantes.
4. No debe usarse para propósitos de construcción.
Suction*, Discharge*, Succión Descarga
Pump Size,
Tamaño de la
Bomba
Wt.(lbs.),Peso
(libras)
Dimensions Determined by Motor, Dimensiones Determinadas por el Motor
Horsepowers, FuerzasWt.
(lbs.),Peso
(libras)
Close Coupled Dimensions Determined by Pump, Dimensiones del Acople Cerrado Determinadas por la Bomba
DD R W X Y Z
140 180 210
H – 4 HOLES4 ORIFICIOS
G
E EA
Z
FF¼ NPT DRAINDRENAJE NPT
L
DISCHARGEDESCARGA
SUCTIONSUCCIÓN
YR
C
B
D
X
DCMAX.
DD
ABMAX. W
P MAX.
Dimension “L”Motor Frame Size,Tamaño del bastidor
del motor de dimensión “L”
Close-Coupled Dimensions and Weights Pesos y dimensiones del acoplamiento corto
Identifier Number,Identifier Number
48
CP DC Motor Frame Size, Bastidor Pump Suction Discharge
Max. Max. DD R W X Y Z 140 180 210 250
Bomba Succión Descarga
L
1CC7MS 1 x 2 – 7 3½ 41⁄8 5½ 3 4 52 – – 1CC8MS 1 x 2 – 8 41⁄4 4 315⁄16 5¾ 33⁄16 4¼ 52 – – 1½CC6MS 1½ x 2 – 6 23¾ 3½ 4½ 3½ 34 – – 1½CC8MS 1½ x 2 – 8 271⁄8 53⁄8 45⁄8 4¼ 5 4¼ 54 113⁄8 115⁄8 2½CC7MS 2½ x 3 – 7 3 21⁄2 255⁄8 51⁄8 4½ 113⁄16 3 4 49 101⁄8 10¾ 11¾ –
3CC8MS 3 x 4 – 7 4* 3* 25¼ 5¾ 51⁄8 33⁄4 43⁄8 2½ 4½ 82 9¾ 103⁄8 113⁄8 – 2CC7MS 2 X 2½-7 2½ 2 257⁄8 5½ 4¾ 3 4¾ 6½ 3½ 4¾ 66 111⁄8 115⁄8 12¾ –
NOTE:All pumps shipped in vertical discharge position. May be rotated in 90º increments. Tighten casing bolts to 25 ft./lbs. torque.
NOTA:Todas las bombas se embarcan con la descarga en posición vertical. Esta posición puede rotarse en incrementos de 90°. Ajustar los pernos de la carcasa a una torsión de 25 pies/libras.
11⁄161 272
11⁄2 1¼
6
10
9¾
10¾
10½25⁄8
ABMAX. Z R
X
DG
E EA
1⁄4" NPT
DCMAX
DD
Y W
L F FB
CPMAX.
PMAX.
H - 4 HOLES4 ORIFICIOS
Motor Frame 3500 RPM 1750 RPM Bastidor 1 Phase 3 Phase 1 Phase 3 Phase del motor ODP TEFC ODP TEFC ODP TEFC ODP TEFC 143 – 3⁄4,1,11⁄2 3⁄4,1,11⁄2 3⁄4,1,11⁄2 – 1⁄2,3⁄4 1⁄2,3⁄4,1 1⁄2,3⁄4,1 145 – 2 2,3 2,3 – 1,11⁄2 11⁄2,2 11⁄2,2 182 3 3 5 3 3 2,3 3 3 184 5 3,5 71⁄2 5 – – 5 5 213 71⁄2 – 10 71⁄2 5 – 71⁄2 71⁄2 215 10 – 15 10,15 – – – – 254TCZ – – 20 – – – – – 256TCZ – – 25 20,25 – – – –
All dimensions in inches and weights in lbs. Do not use for construction purposes.Todas las dimensiones están en pulgadas, el peso en libras. No utilizar para fines de construcción.
Motor Frames and Horsepower Bastidores del motor y potencia en HP
Pump Dimensions and Weights (Dimension “L” determined by Pump and Motor)Peso y dimensiones de la bomba (la dimensión “L” está determinada por la bomba y el motor)
DISCHARGEDESCARGA
SUCTIONSUCCIÓN
Frame Size JM AB P Weight (lbs.) Tamaño del A B D E F G H (Max.) bastidor JM
(Max.)
Pesos (libras)
143 2 41
145 61⁄2 51⁄4 6 31⁄2 23⁄4 21⁄2
1⁄8 11⁄32 65⁄8
57 182 21⁄4 77 184
81⁄2 57⁄8 61⁄2 41⁄2 33⁄4 23⁄4 3⁄16 13⁄32 77⁄8 97
213 23⁄4 122 215
91⁄2 73⁄8 8 51⁄4 41⁄4 31⁄2
7⁄32 13⁄32 95⁄8 155 254 TCZ 91⁄2 41⁄8 265 256 TCZ
111⁄4 9 113⁄4
61⁄4 5 5
1⁄4 17⁄32 111⁄2 320
Mechanical SealSello mecánico
Wt. (lbs.)Pesos
(libras)
Motor Dimensions and Weights (may vary with manufacturer)* Peso y dimensiones del motor (pueden variar de acuerdo al fabricante) *
*For use with ANSI class 150 mating flange. All others are NPT connections.* Para uso con brida de contacto ANSI clase 150. Todas las demás son conexiones NTP.
Close-Coupled Dimensions and WeightsPesos y dimensiones del acoplamiento corto
Identifier No.,
Ident.No.
Goulds PumpsAg. / Irrigation
49
Motor Frames and HorsepowerBastidores del motor y potencia en HP
Motor Dimensions and Weights (may vary with manufacturer)*Pesos y dimensiones del motor (pueden variar de acuerdo al fabricante)*
Pump Dimensions and Weights (Dimension “L” determined by Pump and Motor)Peso y dimensiones de la bomba (la dimension “L” esta determinada por la bomba y el motor)
Close-Coupled Dimensions and Weights Mechanical SealPesos y dimensiones del acoplamiento corto Sello mecánico
NOTE:1. All pumps shipped in vertical discharge position. For other orientations, remove casing bolts, rotate to desired position, and tighten 3⁄8 - 16 casing bolts to 37 ft./lbs. torque.,
1⁄2 - 13 casing bolts to 90 ft./lbs. torque.
2. Dimensions in inches, weight in pounds.3. Not to be used for construction purposes.
4 H-HOLES4 ORIFICIOS
D
G E EA
Z
R
X
BF F
DRAIN PLUGTAPÓN DE DRENAJE
P MAX.
ABAPPROX. W
APPROX. MAX.APROX. MÁX.
CP MAX.
L
DISCHARGE/DESCARGA
SUCTIONSUCCIÓN
Motor Frame AB P* Weight (lbs.) Bastidor A (Max.) B D E F G H (Max.) Pesos (libras) del motor 143JM 41 145JM
61⁄2 51⁄4 6 31⁄2 23⁄4 2
1⁄8 5⁄16 65⁄8 57 182JM 21⁄4 77 184JM
81⁄2 57⁄8 61⁄2 41⁄2 33⁄4 23⁄4 3⁄16 3⁄8 77⁄8 97
213JM 23⁄4 122 215JM 31⁄2
1⁄4 1⁄2 95⁄8 155 213TCZ
91⁄2 73⁄8 8 51⁄4 41⁄4 23⁄4 122 215TCZ 31⁄2
3⁄16 3⁄8 95⁄8 155 254JM 41⁄8 265 256JM
111⁄4 9
91⁄2
61⁄4 5 5
1⁄4 1⁄2 111⁄2 320 284JM 43⁄4 419 286JM
121⁄4 121⁄4 103⁄4
7 51⁄2 51⁄2 1⁄4 1⁄2 131⁄4 422
324JM 51⁄4 562 326JM
131⁄4 131⁄4 12
8 61⁄4 6
5⁄16 5⁄8 151⁄8 588 364TCZ 55⁄8 775 365TCZ
171⁄2 151⁄8 141⁄2
9 7 61⁄8
1 5⁄8 183⁄8 1005
L Motor Frame, Bastidor del motor
140 180 210 250/280 320 360
107⁄8 11½ 12½ 12¾ – – 113⁄8 12 13 13¼ – –
105⁄8 11¼ 12¼ 12½ 13 135⁄8
– – 12½ 12¾ – – 113⁄16 1113⁄16 1213⁄16 131⁄16 135⁄8 – 11 115⁄8 125⁄8 127⁄8 – – – – 12½ 12¾ – – 113⁄8 12 13 13¼ 13¾ 143⁄8 – – 131⁄8 133⁄8 – – – – 12½ 12¾ 13¼ – 10¾ 11½ 123⁄8 – – – – 159⁄16 167⁄16 – – –
NPT Weight Pump Suction Discharge CP DC DD R Drain W X Y Z (lbs) Bomba Succión Descarga Max. Max. Drenaje Pesos NPT (libras) 1½CC10MS 1½ x 2 –10 2* 1½* 30¼ 6¾ 57⁄8 1¼ 5 3 5½ 93 2½CC8MS 2½ x 3 – 8 3* 2½* 30¾ 6¼ 5¼ 113⁄16
1¼ 51⁄8
6 33⁄8 5 78
2½CC9MS 2½ x 3 – 9 33½ 71⁄8 6
7½ 2¾ 5½ 85
2½CC10MS 2½ x 3 – 10 3 2½ 3½ 3⁄8 5
2½CC13MS 2½ x 3 – 13 30¼ 87⁄8 75⁄8 9 3 7½ 139 3CC8MS 3 x 4 – 8 309⁄16 6¼ 53⁄8 ¼ 55⁄16 7 55⁄8 82 3CC10MS 3 x 4 – 10 4 3 303⁄8 73⁄8 6½ 3¾ 51⁄8 7½ 5½ 99 3CC13MS 3 x 4 – 13 33¼ 9½ 81⁄8 5 9
3 7½ 155
4CC8MS 4 x 5 – 8 5 34¼ 67⁄8 5¾ 3⁄8 5½ 8 5 99
4CC10MS 4 x 6 – 10 4 307⁄8 85⁄8 7½ 4½ 5½ 8½ 31⁄8 7 135 4CC13MS 4 x 6 – 13
6 32 9¾ 81⁄8 5¼ 9 3 7½ 171
1¼CC9½MS** 1¼ x 1½ – 9½ 1½* 1¼* 255⁄8 61⁄8 57⁄16 1¼ 1⁄8 45⁄8 8 3¼ 5½ 68 5CC7MS** 5 X 6-7 6 5 28 77⁄8 615⁄16 53⁄8 ¼ 513⁄16 8½ 513⁄16 6¼ 200 6CC9½MS 6 x 8 – 9½ 6CC13MS 6 x 8 – 13 8CC13MS 8 x 10 – 13 4CC16MS 4 x 6 – 16*Denotes NPT connection. All other connections are for use with ANSI class 150 mating flanges.Dimensions in inches, weights in lbs. Do not use for construction purposes.* Indica conexión NPT Las demás conexiones deben usarse con bridas de contacto ANSI clase 150.Dimensiones en pulgadas, peso en libras. No utilizar para fines de construcción.**For JM motors through 215 see packing for larger motors., **Para JM los motores con 215 ven el embalaje para motores más grandes.
NOTA: 1. Todas las bombas se embarcan con la descarga en posición vertical. Para otras orientaciones, retire los pernos de la carcasa, haga rotar la descarga hasta la posición deseada y ajuste los 16 pernos de 3/8 de pulgada a una torsión de 37 pies/libra, y los 13 pernos de 1/2 pulgada a 90 pies/libra.2. Dimensiones en pulgadas, peso en libras.3. No utilizar con fines de construcción.
Frame Size JM ODP TEFC RPM Tamaño del bastidor JM 143 JM 1 1 145 JM 11⁄2, 2 11⁄2, 2 182 JM 3 3 184 JM 5 5 213 JM 71⁄2 71⁄2 215 JM, 215 TCZ 10 10 254 JM 15 15 256 JM 20 20 284 JM 25 25 286 JM 30 30 324 JM 40 40 326 JM 50 50 143 JM 11⁄2 11⁄2 145 JM 2, 3 2 182 JM 5 3 184 JM 71⁄2 5 213 JM 10 71⁄2 215 JM 15 10 215 TCZ 15 – 254 JM 20 15 3500 256 JM 25 20 284 JM 30 25 286 JM 40 30 324 JM 50 40 326 JM 60 50 364 TCZ 75 60 365 TCZ – 75
1750
Y
See Packed Box Dimension Page. (pumps utilize JP motors), Ver la página de dimensiones de la caja empacada. (JP motors)
Identifier No.,
Ident.No.
50
CP DC Motor Frame Size, Bastidor Pump Suction Discharge
Max. Max. DD R W X Y Z 140 180 210 250
Bomba Succión Descarga
L
1CC7PK 1 x 2 – 7 3½ 73⁄16 5½ 3 4 52 – – 1CC8PK 1 x 2 – 8 41⁄4 4 7 5¾ 33⁄16 4¼ 52 – – 1½CC6PK 1½ x 2 – 6 26¾ 3½ 4½ 3½ 34 – – 1½CC8PK 1½ x 2 – 8 301⁄8 53⁄8 45⁄8 75⁄16 5 4¼ 54 147⁄16 115⁄16
2½CC7PK 2½ x 3 – 7 3 2½ 285⁄8 51⁄8 4½ 113⁄16 3 4 49 133⁄16 1313⁄16 1413⁄16 – 8CC7PK 3 x 4 – 7 4* 3* 28¼ 5¾ 51⁄8 3¾ 77⁄16 2½ 4½ 82 1213⁄16 137⁄16 147⁄16 – 2CC7PK 2 x 2½ – 7 2½ 2 293⁄8 5½ 4¾ 3 85⁄8 6½ 3½ 4¾ 71 14¼ 15 165⁄8 –
NOTE:All pumps shipped in vertical discharge position. May be rotated in 90º increments. Tighten casing bolts to 25 ft./lbs. torque.
NOTA:Todas las bombas se embarcan con la descarga en posición vertical. Esta posición puede rotarse en incrementos de 90°. Ajustar los pernos de la carcasa a una torsión de 25 pies/libras.
11⁄1612
1½ 1¼
6
25⁄8
ABMAX. Z R
X
DG
E EA
1⁄4" NPT
DCMAX
DD
Y W
L F FB
CPMAX.
PMAX.
H - 4 HOLES4 ORIFICIOS
Motor Frame 3500 RPM 1750 RPM Bastidor 1 Phase 3 Phase 1 Phase 3 Phase del motor ODP TEFC ODP TEFC ODP TEFC ODP TEFC 143 JP – – – – – – 1 – 145 JP – – 3 2,3 – – 1½,2 1½,2 182 JP 3 – 5 – 3 – 3 3 184 JP 5 – 7½ 5 – – 5 5 213JP 7½ – 10 – 5 – 7½ 7½ 215JP 10 – 15 10,15 7½,10 – 10 10 213 TCZ 7½ – 10 7½ 5 – – – 215 TCZ 10 – 15 10,15 – – – – 254 TCZ – – 20 – – – – – 256 TCZ – – 25 – – – – –
All dimensions in inches and weights in lbs. Do not use for construction purposes.Todas las dimensiones están en pulgadas, el peso en libras. No utilizar para fines de construcción. TCZ indicates west coast fit.
Motor Frames and Horsepower , Bastidores del motor y potencia en HP
Pump Dimensions and Weights (Dimension “L” determined by Pump and Motor)Peso y dimensiones de la bomba (la dimensión “L” está determinada por la bomba y el motor)
DISCHARGEDESCARGA
SUCTIONSUCCIÓN
Frame Size JP AB P Weight (lbs.)
Tamaño del A B D E F G H (Max.) bastidor JP
(Max.)
Pesos (libras)
143 2 41 145
6½ 5¼ 6 3½ 23⁄4 2½ 1⁄8
11⁄32 65⁄8 57
182 2¼ 77 184
8½ 57⁄8 6½ 4½ 33⁄4 2¾ 3⁄16 13⁄32 77⁄8 88
213 9½ 73⁄8 8 5¼ 4¼ 2¾ ¼ 13⁄32 95⁄8
125 215 3½ 155 213 TCZ 2¾ 122 215 TCZ
9½ 73⁄8 8 51⁄4 4¼ 3½
7⁄32 13⁄32 95⁄8 155 254 TCZ 9½ 2¾ 265 256 TCZ
11¼ 9 11¾
61⁄4 5 3½
¼ 17⁄32 11½ 320
TCZ indicates west coast fit.
Packed BoxCaja prensaestopas
30
1213⁄16 139⁄16
1313⁄16131⁄16
Wt. (lbs.)Pesos
(libras)
Motor Dimensions and Weights (may vary with manufacturer)* Peso y dimensiones del motor (pueden variar de acuerdo al fabricante) *
*For use with ANSI class 150 mating flange. All others are NPT connections.* Para uso con brida de contacto ANSI clase 150. Todas las demás son conexiones NTP.
Close-Coupled Dimensions and WeightsPesos y dimensiones del acoplamiento corto
Identifier No.,
Ident.No.
Goulds PumpsAg. / Irrigation
51
SUCTIONSUCCIÓN
NPT DRAINDRENAJE NPT
Y
H - 4 HOLES4 ORIFICIOSL
ABMAX RZ
E EA
X
G DDC
MAXDD
W
FFB
CPMAX
P MAX
JN
M
2 HOLES.62 DIA.
K
*Denotes NPT connection. All other connections are for use with ANSI class 150 mating flanges.* Indica conexión NPT Las demás conexiones deben usarse con bridas de contacto ANSI clase 150.■ Indicates “L” Group pump (dimensions valid for packed box or mechanical seal)., ■ Indica una bomba Grupo “L” (dimensiones válidas para caja empacada o sella mecánico).
NPT Drain Wt. (lbs.) Motor Frame, Bastidor del motor Ident. No. Pump Suction Discharge CP DC DD J K M N R Drenaje W X Y Z Pesos L Ident. No. Bomba Succión Descarga Max. Max. NPT (libras) 140 180 210 250/280 320 360 400 440 1½CC10PK 11⁄2 x 2 –10 2* 1½* 341⁄8 63⁄4 57⁄8 – – – – 1¼ 77⁄8 3 5½ 105 – – 163⁄8 12¾ – – – – 2½CC8PK 21⁄2 x 3 – 8 3* 2½* 345⁄8 61⁄4 51⁄4 – – – – 113⁄16
1⁄4 8 6 33⁄8 5 90 – – 167⁄8 13¼ – – – –
2½CC9PK 21⁄2 x 3 – 9 373⁄8 71⁄8 6 – – – –
7½ 2¾ 5½ 95 – – 161⁄8 12½ 157⁄8 16½ – –
2½CC10PK 21⁄2 x 3 – 10 3 2½ 31⁄2 3⁄8 77⁄8 2½CC13PK 21⁄2 x 3 – 13 341⁄8 87⁄8 75⁄8 – – – –
9 3 7½ 155 – – 163⁄8 12¾ – – – –
3CC9PK 3 x 4 – 8 347⁄16 61⁄4 53⁄8 – – – – 1⁄4 83⁄16 7 55⁄8 90 – – 1611⁄16 131⁄16 161⁄2 – – – 3CC10PK 3 x 4 – 10 4 3 341⁄4 73⁄8 61⁄2 – – – – 33⁄4 8 71⁄2 51⁄2 110 – – 161⁄2 127⁄8 – – – – 3CC13PK 3 x 4 – 13 371⁄8 91⁄2 81⁄8 – – – – 77⁄8 9
3 71⁄2 170 – – 163⁄8 123⁄4 – – – –
4CC8PK 4 x 5 – 8 5 381⁄8 67⁄8 53⁄4 – – – – 83⁄8 8 5 110 – – 167⁄8 131⁄4 165⁄8 171⁄4 – – 4CC10PK 4 x 6 – 10
4 343⁄4 85⁄8 71⁄2 – – – –
4½ 3⁄8 83⁄8 81⁄2 31⁄8 7 145 – – 17 133⁄8 – – – –
4CC13PK 4 x 6 – 13 6 357⁄8 93⁄4 81⁄8 – – – – 81⁄8 9 3 71⁄2 185 – – 163⁄8 123⁄4 161⁄8 – – – 4CC16PK ■ 4 x 6 – 16 471⁄8 123⁄4 11 115⁄16 93⁄4 8 7 85⁄8 12 4 101⁄2 390 – – 1611⁄16 173⁄16 1711⁄16 185⁄16 191⁄4 – 6CC13PK ■ 6 x 8 – 13 8 6 457⁄8 123⁄4 101⁄2 23⁄8 71⁄2 61⁄2 51⁄2 51⁄2 83⁄8 11 3 83⁄4 290 – – 163⁄4 171⁄4 173⁄4 183⁄8 187⁄8 193⁄4 8CC13PK ■ 8 x 10 – 13 10 8 481⁄8 143⁄4 13 23⁄8 71⁄2 61⁄2 51⁄2 63⁄4 85⁄8 123⁄4 4 10 520 – – 171⁄8 175⁄8 181⁄8 183⁄4 191⁄4 201⁄8 1¼CC9½PK 1¼ x 1½ – 9½ 1½* 1¼ 335⁄8 61⁄8 57⁄16 – – – – 1¼ 1⁄8 8½ 8 3¼ 5½ 162 137⁄8 145⁄8 16¼ 16¾ – – – – 5CC7PK 5 x 6 – 7 6 5 42 77⁄8 615⁄16 – – – – 53⁄8 ¼ 911⁄16 8½ 513⁄16 6¼ 204 – – 205⁄16 2013⁄16 215⁄16 – – – 6CC9½PK 6 x 8 – 9½ 8 6 42 103⁄8 9¼ – – – – 61⁄16 ¼ 107⁄32 10½ 7 8¼ 369 – – – 22¼ 22¾ – – –
Horsepower
A
B D E F G H 3500 RPM 1750 RPM
1 Phase 3 Phase 1 Phase 3 Phase ODP TEFC ODP TEFC ODP TEFC ODP TEFC 145JP 6½ 5¼ 6 3½ 2¾ 2½ 1⁄8 11⁄32 65⁄8 – – 3 2 & 3 – – 1½ & 2 1½ & 2 57 182JP 8½ 57⁄8 6½ 4½ 2¾ 2¼ 3⁄16 13⁄32 77⁄8 3 – 5 – – – 3 3 77 184JP 2¾ 5 – 7½ 5 – – 5 5 88 213JP 2¾ 7½ – 10 – 5 – 7½ 7½ 125 215JP
9½ 73⁄8 8 5¼ 4¼ 3½
¼ 13⁄32 95⁄8 10 – 15 10 & 15 71⁄2 & 10 – 10 10 155
254JP 41⁄8 – – 20 – – – 15 15 255 256JP
11¼ 9
11¾
6¼ 5 5
111⁄2 – – 25 20 – – 20 20 280
284JP 4¾
1⁄4 17⁄32 – – 30 25 – – 25 25 410
286JP 12¼ 12¼
12¼
7 5½
5½ 13¼
– – 40 30 – – 30 30 425 324JP 5¼ – – 50 40 – – 40 40 560 326JP
13¼ 13¼
131⁄2
8 61⁄4 6
5⁄16
151⁄8 – – 60 50 – – 50 50 590
364TCZ 55⁄8 21⁄32 – – 75 60 & 75 – – 60 60 775
365TCZ 171⁄2 143⁄8
151⁄8
9 7
61⁄8 1
183⁄8 – – – – – – 75 75 1005
404TCZ 61⁄8 – – – – – – 100 100 1110 405TCZ
191⁄2
171⁄2
165⁄8
10
8 67⁄8
1 13⁄16
201⁄8 – – – – – – 125 – 1163
444TCZ 7¼ 22½ – – – – – – 150 125 1600 445TCZ
21½
191⁄8
19½
11 9 8¼
1 – – – – – – – 150 1708
Motor Dimensions and Weights (may vary with manufacturer)*, Peso y dimensiones del motor (pueden variar de acuerdo al fabricante) *
Wt.Max.
Motor FrameBastidor
del motor
ABMax.
NOTE: 1. All pumps shipped in vertical discharge position. For other orientations, re-move casing bolts, rotate to desired position, and tighten 3⁄8 - 16 casing bolts to 37 ft./lbs.
NOTA: 1. Todas las bombas se embarcan con la descarga en posición vertical. Para otras orientaciones, retire los pernos de la carcasa, haga rotar la descarga hasta la posición deseada
PMax.
torque., ½ - 13 casing bolts to 90 ft./lbs. torque.
2. Dimensions in inches, weight in pounds.3. Not to be used for construction purposes.
y ajuste los 16 pernos de 3/8 de pulgada a una torsión de 37 pies/libra, y los 13 pernos de 1/2 pulgada a 90 pies/libra.2. Dimensiones en pulgadas, peso en libras.3. No utilizar con fines de construcción.
PUMP CENTERLINELÕNEA CENTRAL DE LA BOMBA
ADAPTER FOOTBASE ADAPTADORAADAPTER FOOT
BASE ADAPTADORAPump Dimensions and Weights, Peso y dimensiones de la bomba
Close-Coupled Dimensions and Weights Packed BoxPesos y dimensiones del acoplamiento corto Caja prensaetopas
DISCHARGEDESCARGA
52
Identifier Pump Size, Suction*, Discharge*, DC Max., Wt. (lbs.), HL Motor Frame, Number, Tamaño Succión Descarga CP DC Máx. DD L R W X Y Z Peso (libras) Armazón Ident. No. de la Bomba del Motor HL 2FRM5 2 x 2 – 5 2 2 16¾ 315⁄16 215⁄16 9½ 15⁄8 41⁄8 5
3 35⁄16 26 9½
2½FRM5 2½ x 2½ – 5 2½ 2½ 173⁄8 4¾ 3¾ 95⁄8 33⁄8 4¼ 6 3½ 31 95⁄8
3FRM5 3 x 3 – 5 3 3 175⁄8 55⁄16 45⁄16 103⁄8 23⁄16 4½ 3½ 33⁄8 37 103⁄8
* NPT connections, Conexiones NPT
HP @ 3500 RPM HP @ 1750 RPM 1 PH, Monofásicos 3 PH, Trifásicos 1 PH, Monofásicos 3 PH, Trifásicos ODP TEFC ODP TEFC ODP TEFC ODP TEFC 143T ¾, 1, 1½ ¾, 1, 1½ ¾, 1, 1½ ¾, 1, 1½ ½, ¾ ½, ¾ ½, ¾, 1 ½, ¾, 1
5¼ 133⁄8
65⁄8 45
145T 2 2 2,3 2,3 1 1 – – 14¼ 53
182T 3 – 5 3 – – – – 57⁄8
165⁄8 77⁄8
74
184T 5 3 – 5 – – – – 181⁄8 95
Motor Frame,Armazón del
Motor
HA
HE HE
X
HD
AB MAX.
R Y WDISCHARGE,DESCARGA
SUCTION,SUCCIÓN
DDDCMAX.
HL¼" NPT
HFHB
KEYWAY 1⁄8 x ¼CHAVETERO 1⁄8 x ¼
C MAX.SPACER COUPLING,ACOPLE DEL ESPACIADOR
COUPLING GUARD, GUARDA ACOPLE
3¾
PMAX.
CP
SINGLE PHASE ONLY,MONOFÁSICOS SOLA-
MENTE
3
AB Max.,
AB Máx.
C Max.,
C Máx.
P Max.,
P Máx.
Wt. (lbs.),Peso
(libras)
NOTES:1. Pumps will be shipped with top
vertical discharge as standard. For other orientations, remove casing bolts, rotate to desired position, replace and tighten bolts to 37 lb. – ft.
2. Dimensions are in inches.
3. Motor dimensions may vary with motor manufacturer.
4. Not to be used for construction purposes.
NOTAS:1. Las bombas se transportarán con
la descarga vertical superior como estándar. Para otras orientaciones, retirar los tornillos de la carcasa, rotar a la posición deseada, reemplazar y apretar los tornillos a 37 libras – pies.
2. Las dimensiones son en pulgadas.
3. Las dimensiones del motor pueden que varíen con los fabricantes.
4. No debe usarse para propósitos de construcción.
CPWY
DISCHARGE,DESCARGA
SUCTION,SUCCIÓN
X
DCMAX.
3
¼" NPT56½
1.1251.124
DIA.
H – 4 HOLES, 7⁄16 DIA.H – 4 AGUJEROS, 7⁄16 DIA.
2¾ 2¾7
Z
5¾
KEYWAY ¼ x 1⁄8,CHAVETERO ¼ x 1⁄8
R
Frame Mounted Dimensions Determined by Pump, Dimensiones del Armazón Montado Determinadas por la Bomba
Dimensions Determined by Bedplate, Dimensiones Determinadas por la Fundación
Motor Frame, HA HB HD HE HF HG HL HP
Wt. (lbs.), Motor Shim, Bearing Frame Shim, Armazón del Motor Peso (libras) Deflector del Motor Armazón de Balineras
143T 1¾ –
145T 10 28 8 3¾ 24 2¾ 103⁄8 ¾ 47
182T ¾ –
184T
Horsepowers, Fuerzas
1.1251.124
DIA.
HG
Z
¾L
DD
4 HOLES 5⁄8 DIA.4 AGUJEROS 5⁄8 DIA.
HP
½
Close-Coupled Dimensions and Weights Pesos y dimensiones del acoplamiento corto
Goulds PumpsAg. / Irrigation
53
NOTE:All pumps shipped in vertical discharge position. May be rotated in 90º increments. Tighten casing bolts to 25 ft./lbs. torque.
Dimensions in inches, weights in lbs. Do not use for construction purposes.
NOTA:Todas las bombas se embarcan con la descarga en posición vertical. Esta posición puede rotarse en incrementos de 90°. Ajustar los pernos de la carcasa a una torsión de 25 pies/libras.
Dimensiones en pulgadas, peso en libras. No utilizar para fines de construcción.
Ident. No., Pump Suction Discharge CP DC DD L R W X Y Z Wt.(lbs.) Ident. No. Bomba Succión Descarga Max. Max. Pesos (libras) 1FRM7MS 1 x 2 –7 3½ 41⁄8 5½ 3 4 84 1FRM8MS 1 x 2 – 8 1 16¾ 4¼ 4 8 11⁄16 315⁄16 5¾ 33⁄16 4¼ 84 1½FRM6MS 1½ x 2 – 6 2 3½ 4½ 3½ 66 1½FRM8MS 1½ x 2 – 8 1½ 16½ 53⁄8 45⁄8
7¾
1¼ 4¼ 5 25⁄8 4¼ 86
2½FRM7MS 2½ x 3 – 7 3 2½ 167⁄8 51⁄8 4½ 81⁄8 113⁄16 3 4 81 3FRM7MS 3 x 4 – 7 4* 3* 16½ 5¾ 51⁄8 7¾ 3¾ 43⁄8
6 2½ 4½ 114
*For use with ANSI class 150 mating flange. All others are NPT connections.* Para uso con brida de contacto ANSI clase 150. Todas las demás son conexiones NTP.
Z R DISCHARGEDESCARGA
SUCTIONSUCCIÓN
1⁄4" NPT
X
23⁄4 L
7
51⁄4
23⁄4 56 1⁄2
3⁄4
1⁄2
4 HOLES4 ORIFICIOS
7⁄16 DIA.
KEYWAYCHAVETERO
1⁄4 x 1⁄8
Y W
3
1.1251.124 DIA.
DCMAX
DD
Pump Dimensions and Weights (Dimension “L” determined by Pump and Motor)Peso y dimensiones de la bomba (la dimensión “L” está determinada por la bomba y el motor)
CP
Mechanical SealSello mecánico
Power Frame Dimensions and WeightsPesos y dimensiones del cuadro de fuerza
54
Z R
X
2¾L
7
2¾¾
Y W
37⁄8
CP
4 HOLES7⁄16 DIA.4 ORIFICIOS
½
5¾
56½
DCMAX
DD
¼ NPT
DISCHARGEDESCARGA
SUCTIONSUCCIÓN 1.125
1.124 DIA.
KEYWAY ¼ x 1⁄8CHAVETERO¼ x 1⁄8
Ident. Pump Size, HL Motor Frame No. Tamaño de la Suction*, Discharge*,
CP DC Max.,
DD L R W X Y Z Armazón del Wt. (lbs.),
Ident. Bomba Succión Descarga DC Máx. Motor HL Peso (libras) No. 140-180 210 4FRM5 4 x 4 – 5 4
177⁄8 6½ 5¼ 8¾ 4½
4¼ 7
4 4½ 10¼ 8¾ 142
5FRM6 5 x 5 – 6 5 8 6¼ 921⁄32 5 8 5½ 115⁄32 921⁄32 157
* ANSI Class 125 Flanges, Bridas ANSI Clase 125
HP @ 3500 RPM HP @ 1750 RPM 1 PH, Monofásicos 3 PH, Trifásicos 1 PH, Monofásicos 3 PH, Trifásicos ODP TEFC ODP TEFC ODP TEFC ODP TEFC 143T ¾, 1, 1½ ¾, 1, 1½ ¾, 1, 1½ ¾, 1, 1½ ½, ¾ ½, ¾ ½, ¾, 1 ½, ¾, 1
5¼ 14
65⁄8 45
145T 2 2 2,3 2,3 1 1 2 2 14¼ 53 182T 3 3 5 3 2 2, 3 3 3
63⁄8 165⁄8 77⁄8
74 184T 5 3, 5 7½ 5 3 – 5 5 181⁄8 95 213T 7½ – 10 7½ 5 – 7½ 7½
8½ 20 95⁄8 116
215T 10 – 15 10, 15 – – 10 10 136
Motor Frame,Armazón del
Motor
AB Max.,
AB Máx.
C Max.,
C Máx.
P Max.,
P Máx.
Wt. (lbs.),Peso
(libras)
NOTES:1. Pumps will be shipped with top
vertical discharge as standard. For other orientations, remove casing bolts, rotate to desired position, replace and tighten bolts to 37 lb. – ft.
2. Dimensions are in inches.
3. Motor dimensions may vary with motor manufacturer.
4. Not to be used for construction purposes.
NOTAS:1. Las bombas se transportarán con
la descarga vertical superior como es-tándar. Para otras orientaciones, retirar los tornillos de la carcasa, rotar a la posición deseada, reemplazar y apretar los tornillos a 37 libras – pies.
2. Las dimensiones son en pulgadas.
3. Las dimensiones del motor pueden que varíen con los fabricantes.
4. No debe usarse para propósitos de construcción.
Frame Mounted Dimensions Determined by Pump, Dimensiones del Armazón Montado Determinadas por la Bomba
Dimensions Determined by Bedplate, Dimensiones Determinadas por la Fundación Motor Frame,
HA HB HD HE HF HG HP Wt. (lbs.), Motor Shim, Bearing Frame Shim,
Armazón del Motor Peso (libras) Deflector del Motor Armazón de Balineras 143T
1¾ – 145T
10 28 8 3¾ 24 2¾ ¾ 47 182T ¾ –
184T 213T/215T 12 31 8¼ 4¼ 29 3 1 65 – –
Horsepowers, Fuerzas
CP
KEYWAY 1⁄8 x ¼CHAVETERO 1⁄8 x ¼
1.1251.124
DIA.
3
HL HF
HB
HP
PMAX.
SINGLE PHASE ONLYMONOFÁSICO SOLAMENTE
3¾
WY
DDDCMAX.
SUCTIONSUCCIÓN
DISCHARGEDESCARGA
HG
HD
NPT DRAINDRENAJE NPTHE HE
HA
ABMAX. Z R
X
(4) HOLES5⁄8 DIA.4 ORIFICIOS
SPACER COUPLING, ACOPLAMIENTO ESPACIADORCOUPLING GUARD, PROTECTOR DE ACOPLAMIENTO
C MAX.
Power Frame Dimensions and Weights, Pesos y dimensiones del cuadro de fuerza
2 HOLES.62 DIA.
NM
ADAPTER FOOTBASE ADAPTADORA
PUMP CENTERLINE
LÍNEA CENTRALDE LA BOMBA
Goulds PumpsAg. / Irrigation
55
Identification Pump Suction Discharge DC NPT Drain Weight (lbs.) No., Bomba Succión Descarga CP (Max.) DD L J K M N R Drenaje W X Y Z Pesos Ident. No. NPT (libras) 1½CC10PK 1½ x 2 –10 2* 1½* 217⁄8 63⁄4 57⁄8 93⁄8 — — — — 1¼ 5 3 5½ 155 2½CC8PK 2½ x 3 – 8 3* 2½* 223⁄8 61⁄4 51⁄4 97⁄8 — — — — 113⁄16
¼ 51⁄8
6 33⁄8 5 140
2½CC9PK 2½ x 3 – 9 215⁄8 71⁄8 6 91⁄8 — — — — 7½ 2¾ 5½ 147 2½CC10PK 2½ x 3 – 10 3 21⁄2 3½
3⁄8 5
2½CC13PK 2½ x 3 – 13 217⁄8 87⁄8 75⁄8 93⁄8 — — — —
9 3 7½ 201 3CC8PK 3 x 4 – 8 223⁄16 61⁄4 53⁄8 911⁄16 — — — — ½ 55⁄16 7 55⁄8 144 3CC10PK 3 x 4 – 10 4 3 22 73⁄8 61⁄2 91⁄2 — — — — 33⁄4 51⁄8 7½ 5½ 161 3CC13PK 3 x 4 – 13 217⁄8 91⁄2 81⁄8 93⁄8 — — — — 5 9
3 7½ 217
4CC8PK 4 x 5 – 8 5 223⁄8 67⁄8 53⁄4 97⁄8 — — — — 5½ 8 5 161 4CC10PK 4 x 6 – 10
4 22½ 85⁄8 7½ 10 — — — — 4½
3⁄8 5½ 8½ 31⁄8 7 200 4CC13PK 4 x 6 – 13 6 221⁄8 93⁄4 81⁄8 95⁄8 — — — — 5¼ 9 3 7½ 233 4CC16PK ■ 4 x 6 – 16 26½ 123⁄4 11 1213⁄16 29⁄16 93⁄4 8 7 85⁄8 12 4 10½ 430 6CC13PK ■ 6 x 8 – 13 8 6 251⁄4 123⁄4 10½ 135⁄8 3¾ 7½ 6½ 5½ 5½ 83⁄8 11 3 8¾ 330 8CC13PK ■ 8 x 10 – 13 10 8 26½ 143⁄4 13 14 3¾ 7½ 6½ 5½ 6¾ 85⁄8 12¾ 4 10 515 1¼CC9½PK 1¼ x 1½ – 9½ 1½* 1¼* 255⁄8 61⁄8 57⁄16 127⁄8 – – – – 1¼ 1⁄8 8½ 8 3¼ 5½ 144 2CC7PK 2 x 2½ – 7 2½ 2 26 5½ 4¾ 13¼ – – – – 3 ¼ 85⁄8 6½ 3½ 4¾ 158 5CC7PK 5 x 6 – 7 6 5 293⁄8 77⁄8 615⁄16 165⁄8 – – – – 53⁄8 ¼ 911⁄16 8½ 513⁄16 6¼ 278 6CC9½PK 6 x 8 – 9½ 8 6 313⁄32 103⁄8 9¼ 1811⁄32 – – – – 61⁄16 ¼ 107⁄32 10½ 7 8¼ 429
Motor Dimensions and Weights (may vary with manufacturer)*Pesos y dimensiones del motor (pueden variar de acuerdo al fabricante)*
*Denotes NPT connection. All other connections are for use with ANSI class 150 mating flanges.Dimensions in inches, weights in lbs. Do not use for construction purposes.* Indica conexión NPT Las demás conexiones deben usarse con bridas de contacto ANSI clase 150.Dimensiones en pulgadas, peso en libras. No utilizar para fines de construcción.■ Indicates “L” Group pump., ■ Indica una bomba Grupo “L”.
NOTE:1. All pumps shipped in vertical discharge position. For other orien-tations, remove casing bolts, rotate to desired position, and tighten 3⁄8 - 16 casing bolts to 37 ft./lbs. torque., 1⁄2 - 13 casing bolts to 90 ft./lbs. torque.
NOTA: 1. Todas las bombas se embarcan con la descarga en posición vertical. Para otras orientaciones, retire los pernos de la carcasa, haga rotar la descarga hasta la posición deseada y ajuste los 16 pernos de 3/8 de pulgada a una torsión de 37 pies/libra, y los 13 per-nos de 1/2 pulgada a 90 pies/libra.
Z R
X
31⁄2L
81⁄2
31⁄21
Y W
37⁄8
CP
4 HOLES9⁄16 DIA.
1⁄2
61⁄4
61⁄281⁄2
DCMAX
DD
4 ORIFICIOSDRAIN PLUG
TAPÓN DEDRENAJE
DISCHARGEDESCARGA
SUCTIONSUCCIÓN 1.625
1.624 DIA.
2 HOLES.62 DIA.
NM
K
KEYWAY 3⁄16 x 3⁄8CHAVETERO 3⁄16 x 3⁄8
ADAPTER FOOTBASE ADAPTADORA
ADAPTER FOOTBASE ADAPTADORA
PUMP CENTERLINE
LÍNEA CENTRALDE LA BOMBA
J
Power Frame Dimensions and Weights Mechanical SealPesos y dimensiones del cuadro de fuerza Sello mecánico
2. Dimensions in inches, weight in pounds.3. Not to be used for construction purposes.
2. Dimensiones en pulgadas, peso en libras.3. No utilizar con fines de construc-ción.
56
NOTE:All pumps shipped in vertical discharge position. May be rotated in 90º increments. Tighten casing bolts to 25 ft./lbs. torque.
Dimensions in inches, weights in lbs. Do not use for construction purposes.
NOTA:Todas las bombas se embarcan con la descarga en posición vertical. Esta posición puede rotarse en incrementos de 90°. Ajustar los pernos de la carcasa a una torsión de 25 pies/libras.
Dimensiones en pulgadas, peso en libras. No utilizar para fines de construcción.
Ident. No. Pump Suction Discharge DC Wt.(lbs.) CP DD L R W X Y Z Pesos Ident. No. Bomba Succión Descarga Max.
(libras)
1FRM7PK 1 x 2 –7 31⁄2 73⁄16 51⁄2 3 4 84 1FRM8PK 1 x 2 – 8 1 197⁄16 41⁄4 4 111⁄16 11⁄16 7 53⁄4 33⁄16 41⁄4 84 1½FRM6PK 11⁄2 x 2 – 6 2 31⁄2 41⁄2 31⁄2 66 1½FRM8PK 11⁄2 x 2 – 8 11⁄2 199⁄16 53⁄8 45⁄8
1013⁄16
11⁄4 75⁄16 5 25⁄8 41⁄4 86
2½FRM7PK 21⁄2 x 3 – 7 3 21⁄2 1915⁄16 51⁄8 41⁄2 113⁄16 113⁄16 3 4 81
3FRM7PK 3 x 4 – 7 4* 3* 199⁄16 53⁄4 51⁄8 1013⁄16 33⁄4 77⁄16 6 21⁄2 41⁄2 114
*For use with ANSI class 150 mating flange. All others are NPT connections.* Para uso con brida de contacto ANSI clase 150. Todas las demás son conexiones NTP.
Z R DISCHARGEDESCARGA
SUCTIONSUCCIÓN
1⁄4" NPT
X
23⁄4 L
7
51⁄4
23⁄4 56 1⁄2
3⁄4
1⁄2
4 HOLES4 ORIFICIOS
7⁄16 DIA.
KEYWAYCHAVETERO
1⁄4 x 1⁄8
Y W
3
1.1251.124 DIA.
DCMAX
DD
Pump Dimensions and Weights (Dimension “L” determined by Pump and Motor)Peso y dimensiones de la bomba (la dimensión “L” está determinada por la bomba y el motor)
CP
Packed BoxCaja prensaestopas
Power Frame Dimensions and WeightsPesos y dimensiones del cuadro de fuerza
Goulds PumpsAg. / Irrigation
57
Power Frame Dimensions and Weights Packed BoxPesos y dimensiones del cuadro de fuerza Caja prensaestopas
NOTE:1. All pumps shipped in vertical discharge position. For other orien-tations, remove casing bolts, rotate to desired position, and tighten 3⁄8 - 16 casing bolts to 37 ft./lbs. torque., 1⁄2 - 13 casing bolts to 90 ft./lbs. torque.
2. Dimensions in inches, weight in pounds.3. Not to be used for constructionpurposes.
Motor Dimensions and Weights (may vary with manufacturer)*Pesos y dimensiones del motor (pueden variar de acuerdo al fabricante)*
NOTA: 1. Todas las bombas se embarcan con la descarga en posición vertical. Para otras orientaciones, retire los pernos de la carcasa, haga rotar la descarga hasta la posición deseada y ajuste los 16 pernos de 3/8 de pulgada a una torsión de 37 pies/libra, y los 13 pernos de 1/2 pulgada a 90 pies/libra.2. Dimensiones en pulgadas, peso en libras.3. No utilizar con fines de construcción.
Identification Pump Suction Discharge DC NPT Drain Weight (lbs.) No. Bomba Succión Descarga CP (Max.) DD L J K M N R Drenaje W X Y Z Pesos Ident. No. NPT (libras) 1½FRM10PK 1½ x 2 –10 2* 1½* 24¾ 6¾ 57⁄8 12¼ — — — — 11⁄4 77⁄8 3 5½ 165 2½FRM8PK 2½ x 3 – 8 3* 2½* 25¼ 6¼ 5¼ 12¾ — — — — 113⁄16
1⁄4 8
6 33⁄8 5 150
2½FRM9PK 2½ x 3 – 9 24½ 71⁄8 6 12 — — — — 7½ 2¾ 5½ 160
2½FRM10PK 2½ x 3 – 10 3 212 31⁄2
3⁄8 77⁄8
2½FRM13PK 2½ x 3 – 13 24¾ 87⁄8 75⁄8 12¼ — — — — 9 3 7½ 215 3FRM8PK 3 x 4 – 8 221⁄16 6¼ 53⁄8 125⁄16 — — — —
1⁄4 83⁄16 7 55⁄8 155 3FRM10PK 3 x 4 – 10 4 3 247⁄8 73⁄8 6½ 123⁄8 — — — — 3¾ 8 7½ 5½ 170 3FRM13PK 3 x 4 – 13 24¾ 9½ 81⁄8 12¼ — — — — 77⁄8 9
3 7½ 230
4FRM8PK 4 x 5 – 8 5 25¼ 67⁄8 5¾ 12¾ — — — — 83⁄8 8 5 170 4FRM10PK 4 x 6 – 10 4 253⁄8 85⁄8 7½ 127⁄8 — — — —
4½ 3⁄8 83⁄8 8½ 31⁄8 7 210
4FRM13PK 4 x 6 – 13 6 25 9¾ 81⁄8 12½ — — — — 81⁄8 9 3 7½ 245 4FRM16PK ■ 4 x 6 – 16 26½ 12¾ 11 1213⁄16 29⁄16 9¾ 8 7 85⁄8 12 4 10½ 430 6FRM13PK ■ 6 x 8 – 13 8 6 25¼ 12¾ 10½ 135⁄8 3¾ 7½ 6½ 5½ 5½ 83⁄8 11 3 8¾ 330 8FRM13PK ■ 8 x 10 – 13 10 8 26½ 14¾ 13 14 3¾ 7½ 6½ 5½ 6¾ 85⁄8 12¾ 4 10 515 1¼FRM9½PK 1¼ x 1½ – 9½ 1½* 1¼* 255⁄8 61⁄8 57⁄16 127⁄8 – – – – 1¼ 1⁄8 8½ 8 3¼ 5½ 144 2FRM7PK 2 x 2½ – 7 2½ 2 26 5½ 4¾ 13¼ – – – – 3 ¼ 85⁄8 6½ 3½ 4¾ 158 5FRM7PK 5 x 6 – 7 6 5 293⁄8 77⁄8 615⁄16 165⁄8 – – – – 53⁄8 ¼ 911⁄16 8½ 513⁄16 6¼ 278 6FRM9½PK 6 x 8 – 9½ 8 6 313⁄32 103⁄8 9¼ 1811⁄32 – – – – 61⁄16 ¼ 107⁄32 10½ 7 8¼ 429
Z R
X
31⁄2L
81⁄2
31⁄21
Y W
37⁄8
CP
4 HOLES9⁄16 DIA.
1⁄2
61⁄4
61⁄281⁄2
DCMAX
DD
4 ORIFICIOSDRAIN PLUGTAPÓN DEDRENAJE
DISCHARGEDESCARGA
SUCTIONSUCCIÓN 1.625
1.624 DIA.
2 HOLES.62 DIA.
NM
K
KEYWAY 3⁄16 x 3⁄8CHAVETERO 3⁄16 x 3⁄8
■ Indicates “L” Group pump., ■ Indica una bomba Grupo “L”.
ADAPTER FOOT, BASE ADAPTADORA
PUMP CENTERLINELÕNEA CENTRALDE LA BOMBA
ADAPTER FOOTBASE ADAPTADORA
J
58
Wt.(lbs.) Motor Frame Size, Tamaño del bastidor Ident. No. Pump Suction Discharge CP DC DD R W X Y Z Pesos 140 / 180 210 250 / 280 Ident. No. Bomba Succión Descarga Max. Max. (libras) HL 1FRM7MS 1 x 2 – 7 3½ 41⁄8 5½ 3 4 84 – – 1FRM8MS 1 x 2 – 8 4¼ 4 11⁄16 315⁄16 5¾ 33⁄16 4¼ 84 – 1½FRM6MS 11⁄2 x 2 – 6 3½ 4½ 3½ 66 9¼ 7¾ – 1½FRM8MS 11⁄2 x 2 – 8 53⁄8
1¼ 41⁄4 5 25⁄8 4¼ 86 – 2½FRM7MS 21⁄2 x 3 – 7 3 21⁄2 167⁄8 51⁄8 4½ 113⁄16 3 4 81 95⁄8 81⁄8 43⁄8
3FRM7MS 3 x 4 – 7 4* 3* 16½ 53⁄4 51⁄8 3¾ 43⁄8 2½ 4½ 114 9¼ 7¾ 7
Bedplate Dimensions and Weights, Pesos y dimensiones de la place de asiento Motor Frame Motor Bearing Frame Weight (lbs.) Bastidor HA HB HD HE HF HG HP* Shim Shim Cuña del Pesos del motor Cuña marco de cojinetes (libras)
143 T 145 T
1¾
–
182 T 10 28 8 3¾ 24 2¾ ¾ 48
184 T
¾ –
213 T 215 T
12 31 8¼ 4¼ 29 3 1 – – 65
254 T 256 T
13 42 9¼ 5¼ 38½ 4 1¾
– 1 110
284 TS/T 15 44 10½ 5¾ 40½ 3½ – 1¾ 124
* “HP” Dimension at Motor end only. * Dimensión “HP” al extremo del motor únicamente.
Z R
X
ABMAX
HE HE
HA
DD
¼" NPT HF
HB
HP
4 HOLES5⁄8 DIA.
4 ORIFICIOS
P MAX
3¾
3
CP
YSINGLE PHASE
ONLY
DCMAX
1.1251.124
HD
HG
W
HL
C MAX
(Motor End Only)(Extremo del motor únicamente)
DIA.
DISCHARGEDESCARGA
SUCTIONSUCCIÓN
NOTE:1. All pumps shipped in vertical discharge position. May be rotated in 90° increments. Tighten casing bolts to 25 ft./lbs. torque.
2. Dimensions in inches, weights in lbs. Do not use for construc-tion purposes.3. Motor dimensions and weights very with manufacturer.
NOTA:1. Todas las bombas se embarcan con la descarga en posición vertical. Esta posición puede rotarse en incrementos de 90°. Ajustar los pernos de la carcasa a una torsión de 25 pies/libras.2. Dimensiones en pulgadas, peso en libras. No utilizar para fines de construcción.3. Las dimensiones y el peso de los motores varían de acuerdo al fabricante.
Motor Frame 3500 RPM 1750 RPM Wt. (lbs.) Bastidor 1 Phase 3 Phase 1 Phase 3 Phase AB C P Pesos del motor ODP TEFC ODP TEFC ODP TEFC ODP TEFC Max. Max. Max. (libras) 143 T ½,1,1½ ¾,1,1½ ¾,1,1½ ¾,1,1½ ½,¾ ½,¾ ½,¾,1 ½,¾,1 133⁄8 45 145 T 2 2 2,3 2,3 1,1½ 1,1½ 1½,2 1½,2 14¼ 53 182 T 3 3 5 3 2 2,3 3 3 165⁄8 74 184 T 5 3,5 71⁄2 5 3 – 5 5 181⁄8 95 213 T 7½ – 10 7½ 5 – 7½ 7½ 18 116 215 T 10 – 15 10,15 – – – – 191⁄8 136 254 T – – 20 — – – – – 215⁄8 266 256 T – – 25 20,25 – – – – 233⁄8 264 284 TS/T – – 30 25 – – – – 125⁄8 247⁄8 15 392
SPACER COUPLING, ACOPLAMIENTO ESPACIADORCOUPLING GUARD, PROTECTOR DE ACOPLAMIENTO
Motor Dimensions and Weights, Peso y dimensiones del motor
5¼ 5¼
57⁄8 57⁄8
73⁄8 73⁄8
101⁄8 101⁄8
*For use with ANSI class 150 mating flange. All others are NPT connections. , * Para uso con brida de contacto ANSI clase 150. Todas las demás son conexiones NTP.
1 163⁄82
11⁄2
6
16½
KEYWAYCHAVETERO
1⁄8 x ¼
MONOFÁSICO SOLAMENTE
Mechanical SealSello mecánico
Pump Dimensions and Weights (Dimension “HL” determined by Pump and Motor)Peso y dimensiones de la bomba (la dimensión “HL” está determinada por la bomba y el motor)
Bedplate AssemblyInstalación de la placa de asiento
Goulds PumpsAg. / Irrigation
59
Pump Dimensions and Weights, Peso y dimensiones de la bomba
Channel Steel Bedplate. Clockwise rotation viewed from drive end.Placa de asiento de acero acanalado. Rotación dextrorsa (sentido de las agujas del reloj) cuando se mira desde el extremo del motor.
NOTE: 1. All pumps shipped in vertical discharge position. For other orientations, remove casing bolts, rotate to desired position, and tighten 3⁄8 - 16 casing bolts to 37 ft./lbs. torque., ½ - 13 casing bolts to 90 ft./lbs. torque.
2. Dimensions in inches, weight in pounds.3. Not to be used for construction purposes.NOTA: 1. Todas las bombas se embarcan con la descarga en posición vertical. Para otras orientaciones, retire los pernos de la carcasa, haga rotar la descarga hasta la posición deseada y ajuste los 16 pernos de 3⁄8 de pulgada a una torsión de 37 pies/libra, y los 13 pernos de ½ pulgada a 90 pies/libra.2. Dimensiones en pulgadas, peso en libras.3. No utilizar con fines de construcción.
Motor and Bedplate Dim. and Weights (may vary with manufacturer.) Peso y dim. del motor y la placa de asiento (pueden variar de acuerdo al fabricante)
143T – – – – – – – – 5¼ 133⁄8 5¼ 45 2¾ 145T – – – – – – 1 1 14¼ 53
– 182T – – 5 – 1,1½ 1,1½ 1,1½ 1,1½ 57⁄8 165⁄8 57⁄8 74 184T – – – – — — 5 5 57⁄8 18 8 95 1¾
213T – – – – — — 7½ 7½ 18 116 13 42 10¼ 5¼ 38½ 4 111 1 – 215T – – – – 15 — 10 10
73⁄8 191⁄8
95⁄8 136
254T – – – – 20 15 15 15 215⁄8 266 – – 256T – – – – 25 20 20 20
101⁄8 233⁄8
13 264
284TS/T – – – – 30 25 25 25 247⁄8 392 – ¾ 286TS/T – – – – 40 30 30 30
125⁄8 265⁄8
15 422
15 44 101⁄2 53⁄4 401⁄2 31⁄2 124
324TS/T – – – – 50 40 40 40 28¾ 592 12 – 1¾ 326TS/T – – – – 60 50 50 50
141⁄8 30¼
173⁄8 634 18 48 71⁄4 441⁄2 4 183
364TS/T – – – – 75 60 60 60 315⁄8 834 – 2¾ 356TS/T – – – – 100 75 75 75
151⁄8 325⁄8
187⁄8 1000
13
Three phase, Trifásico
Motor Frame
Bastidordel
motor
HP @ 3500 RPM
ODP TEFC TEFCODP
AB C P Max. Max. Max. HA HB HD HE HF HG
Bedplate Data, Datos de la placa de asientoBearing FrameShim, Cuña del
bastidor de cojinetes
Motor Shim
Cuña delmotor
Wt.(lbs.)Pesos
(libras)
HP @ 1750 RPM - T-Frame Only, Bastidor
T únicamenteWeight
(lbs)Pesos
(libras)
NPT Weight Ident No. Pump Suction Discharge CP DC DD L R Drain W X Y Z (lbs) Ident. No. Bomba Succión Descarga Max. Max. Drenaje Pesos NPT (libras) 1½FRM10MS 1½ x 2 –10 2* 1½* 217⁄8 6¾ 57⁄8 93⁄8 1¼ 5 3 5½ 155 2½FRM8MS 2½ x 3 – 8 3* 2½* 223⁄8 6¼ 5¼ 97⁄8 113⁄16
1¼ 51⁄8
6 33⁄8 5 140
2½FRM9MS 2½ x 3 – 9 215⁄8 71⁄8 6 91⁄8
7½ 2¾ 5½ 147
2½FRM10MS 2½ x 3 – 10 3 2½ 3½ 3⁄8 5 2½FRM13MS 2½ x 3 – 13 217⁄8 87⁄8 75⁄8 93⁄8
9 3 7½ 201 3FRM8MS 3 x 4 – 8 223⁄16 6¼ 53⁄8 97⁄16
¼ 55⁄16 7 55⁄8 144 3FRM10MS 3 x 4 – 10 4 3 22 73⁄8 6½ 9½
3¾ 51⁄8 7½ 5½ 161
3FRM13MS 3 x 4 – 13 217⁄8 9½ 81⁄8 93⁄8 5 9 3 7½ 217
4FRM8MS 4 x 5 – 8 5 223⁄8 67⁄8 5¾ 97⁄8 3⁄8 5½ 8 5 161
4FRM10MS 4 x 6 – 10 4 22½ 85⁄8 7½ 10 4½ 5½ 8½ 31⁄8 7 200 4FRM13MS 4 x 6 – 13
6 221⁄8 9¾ 81⁄8 95⁄8 5¼ 9 3 7½ 233
1¼FRM9½MS 1¼ x 1½ – 9½ 1½* 1¼* 255⁄8 61⁄8 57⁄16 127⁄8 1¼ 1⁄8 8½ 8 3¼ 5½ 144 2FRM7MS 2 x 2½ – 7 2½ 2 26 5½ 4¾ 13¼ 3 ¼ 85⁄8 6½ 3½ 4¾ 158 5FRM7MS 5 x 6 – 7 6 5 293⁄8 77⁄8 615⁄16 165⁄8 53⁄8 ¼ 911⁄16 8½ 513⁄16 6¼ 278 6FRM9½MS 6 x 8 – 9½ 8 6 313⁄32 103⁄8 9¼ 1811⁄32 61⁄16 ¼ 107⁄32 10½ 7 8¼ 429*Denotes NPT connection. All other connections are for use with ANSI class 150 mating flanges.* Indica conexión NPT Las demás conexiones deben usarse con bridas de contacto ANSI clase 150.
Bedplate Assembly Mechanical SealInstalación de la placa de asiento Sello mecánico
KEYWAY 3⁄16 x 3⁄8CHAVETERO 3⁄16 x 3⁄8
1.6251.624 DIA.
37⁄8
L HF
HB
1¾
PMAX.
SINGLE PHASE ONLYMONOFÁSICO SOLAMENTE
3¾ C MAX.CP
WY
DDDC MAX.
SUCTIONSUCCIÓN
DISCHARGEDESCARGA
HG
HD
NPT DRAINDRENAJE NPTHE HE
HA
AB MAX. Z R
X
(4) HOLES5⁄8 DIA.4 ORIFICIOS
*
* Dimension will include any special shims required to match pump centerline to motor.* La dimensión incluye cualquier cuña especial que se requiera para hacer coincidir la línea central de la bomba con el motor.
SPACER COUPLING, ACOPLAMIENTO ESPACIADORCOUPLING GUARD, PROTECTOR DE ACOPLAMIENTO
Single phase, MonofásicoODP TEFC TEFCODP
60
Motor Frame 3500 RPM 1750 RPM Wt. (lbs.) Bastidor 1 Phase 3 Phase 1 Phase 3 Phase AB C P Pesos del motor ODP TEFC ODP TEFC ODP TEFC ODP TEFC Max. Max. Max. (libras) 143 T 1⁄2,1,11⁄2 3⁄4,1,11⁄2 3⁄4,1,11⁄2 3⁄4,1,11⁄2 1⁄2,3⁄4 1⁄2,3⁄4 1⁄2,3⁄4,1 1⁄2,3⁄4,1 133⁄8 45 145 T 2 2 2,3 2,3 1,11⁄2 1,11⁄2 11⁄2,2 11⁄2,2 141⁄4 53 182 T 3 3 5 3 2 2,3 3 3 165⁄8 74 184 T 5 3,5 71⁄2 5 3 – 5 5 181⁄8 95 213 T 71⁄2 – 10 71⁄2 5 – 71⁄2 71⁄2 18 116 215 T 10 – 15 10,15 – – – – 191⁄8 136 254 T – – 20 – – – – – 215⁄8 266 256 T – – 25 20,25 – – – – 233⁄8 264 284 TS/T – – 30 25 – – – – 125⁄8 247⁄8 15 392
Wt.(lbs.) Motor Frame Size, Tamaño del bastidor Ident. No. Pump Suction Discharge CP DC DD R W X Y Z Pesos 140 / 180 210 250 / 280 Ident. No. Bomba Succión Descarga Max. Max. (libras) HL 1FRM7PK 1 x 2 – 7 3½ 73⁄16 5½ 3 4 84 – – 1FRM8PK 1 x 2 – 8 4¼ 4 11⁄16 7 5¾ 33⁄16 4¼ 84 – 1½FRM6PK 1½ x 2 – 6 3½ 4½ 3½ 66 125⁄16 1013⁄16 – 1½FRM8PK 1½ x 2 – 8 53⁄8
1¼ 75⁄16 5 25⁄8 4¼ 86 –
2½FRM7PK 2½ x 3 – 7 3 2½ 1915⁄16 51⁄8 4½ 113⁄16 3 4 81 1211⁄16 113⁄16 77⁄16
3FRM7PK 3 x 4 – 7 4* 3* 199⁄16 5¾ 51⁄8 3¾ 77⁄16 21⁄2 4½ 114 125⁄16 1013⁄16 101⁄16
Motor Frame Motor Bearing Frame Weight (lbs.) Bastidor HA HB HD HE HF HG HP* Shim Shim Cuña del Pesos del motor Cuña marco de cojinetes (libras)
143 T 145 T 13⁄4 – 182 T
10 28 8 33⁄4 24 23⁄4 3⁄4 48
184 T
3⁄4 –
213 T 215 T
12 31 81⁄4 41⁄4 29 3 1 – – 65
254 T 256 T
13 42 91⁄4 51⁄4 381⁄2 4 13⁄4
– 1 110
284 TS/T 15 44 101⁄2 53⁄4 401⁄2 31⁄2 – 13⁄4 124
* “HP” Dimension at Motor end only. * Dimensión “HP” al extremo del motor únicamente.
Z R
X
ABMAX
HE HE
HA
DD
1⁄4" NPT HF
HB
HP
4 HOLES5⁄8 DIA.
4 ORIFICIOS
P MAX
33⁄4
3
CP
YSINGLE PHASE
ONLY
DCMAX
1.1251.124
HD
HG
W
HL
C MAX
(Motor End Only)(Extremo del motor únicamente)
DIA.
DISCHARGEDESCARGA
SUCTIONSUCCIÓN
NOTE:1. All pumps shipped in vertical discharge position. May be rotated in 90° increments. Tighten casing bolts to 25 ft./lbs. torque.
2. Dimensions in inches, weights in lbs. Do not use for construction purposes.3. Motor dimensions and weights very with manufacturer.
NOTA:1. Todas las bombas se embarcan con la descarga en posición ver-tical. Esta posición puede rotarse en incrementos de 90°. Ajustar los pernos de la carcasa a una torsión de 25 pies/libras.2. Dimensiones en pulgadas, peso en libras. No utilizar para fines de construcción.3. Las dimensiones y el peso de los motores varían de acuerdo al fabricante.
SPACER COUPLING, ACOPLAMIENTO ESPACIADORCOUPLING GUARD, PROTECTOR DE ACOPLAMIENTO
Bedplate Dimensions and Weights, Pesos y dimensiones de la place de asiento
Motor Dimensions and Weights, Peso y dimensiones del motor
51⁄4 51⁄4
57⁄8 57⁄8
73⁄8 73⁄8
101⁄8 101⁄8
*For use with ANSI class 150 mating flange. All others are NPT connections., * Para uso con brida de contacto ANSI clase 150. Todas las demás son conexiones NTP.
12
1½
6
KEYWAYCHAVETERO
1⁄8 x 1⁄4
MONOFÁSICO SOLAMENTE
Packed BoxCaja prensaestopas
197⁄16
199⁄16
Pump Dimensions and Weights (Dimension “HL” determined by Pump and Motor)Peso y dimensiones de la bomba (la dimensión “HL” está determinada por la bomba y el motor)
Bedplate AssemblyInstalación de la placa de asiento
Goulds PumpsAg. / Irrigation
61
Pump Dimensions and Weights, Peso y dimensiones de la bomba
Engineering Data – Bedplate Assembly Packed BoxDatos de ingeniería – Instalación de la placa de asiento Caja prensaestopas
NPT Weight Ident. No. Pump Suction Discharge CP DC DD L R Drain W X Y Z (lbs) Ident. No. Bomba Succión Descarga Max. Max. Drenaje Pesos NPT (libras) 1½FRM10MS 1½ x 2 –10 2* 1½* 24¾ 63⁄4 57⁄8 12¼ 1¼ 77⁄8 3 51⁄2 165 2½FRM8MS 2½ x 3 – 8 3* 2½* 25¼ 6¼ 5¼ 12¾ 113⁄16
¼ 8
6 33⁄8 5 150
2½FRM9MS 2½ x 3 – 9 24½ 71⁄8 6 12
7½ 2¾ 5½ 160
2½FRM10MS 2½ x 3 – 10 3 2½ 31⁄2 3⁄8 77⁄8 2½FRM13MS 2½ x 3 – 13 24¾ 87⁄8 75⁄8 12¼
9 3 71⁄2 215 3FRM8MS 3 x 4 – 8 221⁄16 6¼ 53⁄8 125⁄16
¼ 83⁄16 7 55⁄8 155 3FRM10MS 3 x 4 – 10 4 3 247⁄8 73⁄8 6½ 123⁄8
3¾ 8 71⁄2 51⁄2 170
3FRM13MS 3 x 4 – 13 24¾ 9½ 81⁄8 12¼ 77⁄8 9 3 71⁄2 230
4FRM8MS 4 x 5 – 8 5 25¼ 67⁄8 53⁄4 12¾ 3⁄8 83⁄8 8 5 170
4FRM10MS 4 x 6 – 10 4 253⁄8 85⁄8 7½ 127⁄8 41⁄2 81⁄2 31⁄8 7 210 4FRM13MS 4 x 6 – 13
6 25 9¾ 81⁄8 12½ 81⁄8 9 3 71⁄2 245
1¼FRM9½MS 1¼ x 1½ – 9½ 1½* 1¼* 255⁄8 61⁄8 57⁄16 127⁄8 1¼ 1⁄8 8½ 8 3¼ 5½ 144 2FRM7MS 2 x 2½ – 7 2½ 2 26 5½ 4¾ 13¼ 3 ¼ 85⁄8 6½ 3½ 4¾ 158 5FRM7MS 5 x 6 – 7 6 5 293⁄8 77⁄8 615⁄16 165⁄8 53⁄8 ¼ 911⁄16 8½ 513⁄16 6¼ 278 6FRM9½MS 6 x 8 – 9½ 8 6 313⁄32 103⁄8 9¼ 1811⁄32 61⁄16 ¼ 107⁄32 10½ 7 8¼ 429
NOTE: 1. All pumps shipped in vertical discharge position. For other orientations, remove casing bolts, rotate to desired position, and tighten 3⁄8 - 16 casing bolts to 37 ft./lbs. torque., 1⁄2 - 13 casing bolts to 90 ft./lbs. torque.
2. Dimensions in inches, weight in pounds.3. Not to be used for con-struction purposes.NOTA: 1. Todas las bombas se embarcan con la descarga en posición vertical. Para otras orientaciones, retire los pernos de la carcasa, haga rotar la descarga has–ta la posición de-seada y ajuste los 16 pernos de 3⁄8 de pulgada a una torsión de 37 pies/libra, y los 13 pernos de 1/2 pulgada a 90 pies/libra.2. Dimensiones en pulgadas, peso en libras.3. No utilizar con fines de construcción*Denotes NPT connection. All other connections are for use with ANSI class 150 mating flanges.
* Indica conexión NPT Las demás conexiones deben usarse con bridas de contacto ANSI clase 150.
KEYWAY 3⁄16 x 3⁄8CHAVETERO 3⁄16 x 3⁄8
1.6251.624DIA.
37⁄8
L HF
HB
13⁄4
PMAX.
SINGLE PHASE ONLYMONOFÁSICO SOLAMENTE
33⁄4 C MAX.CP
WY
DDDC MAX.
SUCTIONSUCCIÓN
DISCHARGEDESCARGA
HG
HD
NPT DRAINDRENAJE NPTHE HE
HA
AB MAX. Z R
X
(4) HOLES5⁄8 DIA.4 ORIFICIOS
*
* Dimension will include any special shims required to match pump centerline to motor.* La dimensión incluye cualquier cuña especial que se requiera para hacer coincidir la línea central de la bomba con el motor.
SPACER COUPLING, ACOPLAMIENTO ESPACIADORCOUPLING GUARD, PROTECTOR DE ACOPLAMIENTO
Channel Steel Bedplate. Clockwise rotation viewed from drive end.Placa de asiento de acero acanalado. Rotación dextrorsa (sentido de las agujas del reloj) cuando se mira desde el extremo del motor.
Motor and Bedplate Dim. and Weights (may vary with manufacturer.) Peso y dim. del motor y la placa de asiento (pueden variar de acuerdo al fabricante)
143T – – – – – – – – 5¼ 133⁄8 5¼ 45 2¾ 145T – – – – – – 1 1 14¼ 53 – 182T – – 5 – 1,1½ 1,1½ 1,1½ 1,1½ 57⁄8 165⁄8 57⁄8 74 184T – – – – — — 5 5 57⁄8 18 8 95 1¾
213T – – – – — — 7½ 7½ 18 116 13 42 10¼ 5¼ 38½ 4 111 1 – 215T – – – – 15 — 10 10
73⁄8 191⁄8
95⁄8 136
254T – – – – 20 15 15 15 215⁄8 266 – – 256T – – – – 25 20 20 20
101⁄8 233⁄8
13 264
284TS/T – – – – 30 25 25 25 247⁄8 392 – ¾ 286TS/T – – – – 40 30 30 30
125⁄8 265⁄8
15 422
15 44 101⁄2 53⁄4 401⁄2 31⁄2 124
324TS/T – – – – 50 40 40 40 28¾ 592 12 – 1¾ 326TS/T – – – – 60 50 50 50
141⁄8 30¼
173⁄8 634 18 48 71⁄4 441⁄2 4 183
364TS/T – – – – 75 60 60 60 315⁄8 834 – 2¾ 356TS/T – – – – 100 75 75 75
151⁄8 325⁄8
187⁄8 1000
13
Three phase, Trifásico
Motor Frame
Bastidordel
motor
HP @ 3500 RPM
ODP TEFC TEFCODP
AB C P Max. Max. Max. HA HB HD HE HF HG
Bedplate Data, Datos de la placa de asientoBearing FrameShim, Cuña del
bastidor de cojinetes
Motor Shim
Cuña delmotor
Wt.(lbs.)Pesos
(libras)
HP @ 1750 RPM - T-Frame Only, Bastidor
T únicamenteWeight
(lbs)Pesos
(libras)Single phase, Monofásico
ODP TEFC TEFCODP
62
Engineering Data – Bedplate Assembly Mechanical Seal & Packed BoxDatos de ingeniería – Instalación de la placa de asiento Sello Mecánico & Caja prensaestopas
Motor and Bedplate Dimensions and Weights, Peso y dimensiones del motor y la placa de asiento
Dimensions and Weights, Pesos y dimensiones
KEYWAY 3⁄16 x 3⁄8CHAVETERO 3⁄16 x 3⁄8
1.6251.624 DIA.
37⁄8
L HF
HB
21⁄8
PREF.
SINGLE PHASE ONLYMONOFÁSICO SOLAMENTE
33⁄4 C REF.CP
WY
DDDC MAX.
SUCTIONSUCCIÓN
DISCHARGEDESCARGA
6
HD
NPT DRAINDRENAJE NPTHE HE
HA
AB REF. Z R
X
3⁄4" DIA.4-PLACES
NOTE: 1. Dimensions in inches, weight in pounds. NOTA: 1. Dimensiones en pulgadas, peso en libras. 2. Not to be used for construction purposes. 2. No utilizar con fines de construcción.
SPACER COUPLING, ACOPLAMIENTO ESPACIADORCOUPLING GUARD, PROTECTOR DE ACOPLAMIENTO
Channel Steel Bedplate. Clockwise rotation viewed from drive end.Placa de asiento de acero acanalado. Rotación dextrorsa (sentido de las agujas del reloj) cuando se mira desde el extremo del motor.
▼
▼
3⁄8
Pump, Bomba Size, Tamaño Suction, Succión Discharge, Descarga CP DC Max. DD L R W X Y Z 6FRM13 6 x 8-13 8 6 251⁄4 123⁄4 101⁄2 135⁄8 51⁄2 83⁄8 11 3 83⁄4 8FRM13 8 x 10-13 10 8 261⁄2 143⁄4 13 14 63⁄4 85⁄8 123⁄4 4 10 4FRM16 4 x 6-16 6 4 261⁄2 123⁄4 11 1213⁄16 41⁄2 85⁄8 12 4 101⁄2
Motor Data Baseplate Data
HP @ 3500 RPM HP @ 1750 RPM
Three Phase, Trifásica AB Ref. C Ref. P Ref. HA HB HD HE HF
ODP TEFC ODP TEFC Open Encl. 284T/286T 25, 30 25, 30 12.20 21.22 13.62 340 405 2" 324T/326T 40, 50 40, 50 14.13 30 16.50 440 580 1" 324TS/325TS 50, 60 40, 50 29 480 520 364T/365T 60, 75 60, 75 15.06 34 18.25 665 835
48
43.75 244
364TS/365TS 75, 100 60, 75 32 730 820 N/A 404TS/405TS 125, 150 100 18 36 20.13 950 1150 6FRM13 404T/405T 100, 125 100 39 930 1160
29.06
15.75 13.66 1"
444TS/445TS 200-300 125, 150 19.56 41 22.38 1250 1615 444T/445T 150-300 125-200 45 1370 1650 60.25 56 345 447TS 350 200 47 1800 2550 N/A 449TS 400-450 250-400 21.69 51 23.75 1850 2550 447T 350 250 48 1800 2260 324T/326T 40, 50 40, 50 14.13 30 16.50 440 580 1" 324TS/325TS 50, 60 40, 50 29 480 520 364T/365T 60, 75 60, 75 15.06 34 18.25 665 835 48 43.75 244 364TS/365TS 75, 100 60, 75 32 730 820 N/A 404TS/405TS 125, 150 100 18 36 20.13 950 1150 8FRM13 404T/405T 100, 125 100 39 930 1160 29.06 15.75 13.66 1" 444TS/445TS 200-300 125, 150 19.56 41 22.38 1250 1615 444T/445T 150-300 125-200 45 1370 1650 60.25 56 345 447TS 350 200 47 1800 2550 N/A 449TS 400-450 250-400 21.69 51 23.75 1850 2550 447T 350 250 48 1800 2260 324T/326T 40, 50 40, 50 14.13 30 16.50 440 580 1" 324TS/325TS 50, 60 40, 50 29 480 520 364T/365T 60, 75 60, 75 15.06 34 18.25 665 835 48 43.75 244 364TS/365TS 75, 100 60, 75 32 730 820 N/A 404TS/405TS 125, 150 100 18 36 20.13 950 1150 4FRM16 404T/405T 100, 125 100 39 930 1160 29.06 15.75 13.66 1" 444TS/445TS 200-300 125, 150 19.56 41 22.38 1250 1615 444T/445T 150-300 125-200 45 1370 1650 60.25 56 345 447TS 350 200 47 1800 2550 N/A 449TS 400-450 250-400 21.69 51 23.75 1850 2550 447T 350 250 48 1800 2260
PumpSize,
Tamaño de
Bomba
MotorFrame,Bastidor
del motor
Weight(lb),
Pesos(libras)
Shim HeightUnder MotorShim Height
UnderMotor
Weight (lbs) Ref.,
Pesos (libras) Ref.
+/- 1⁄4 +/- 1⁄4 +/- 1⁄8 +/- 1⁄16 +/- 1⁄16
Goulds PumpsAg. / Irrigation
63
Ident. No. Pump Suction Discharge DC NPT Drain Weight (lbs.) Ident. No. Bomba Succión Descarga CP (Max.) DD J K M N R Drenaje W X Y Z Pesos NPT (libras) 1½SAE10PK 1½ x 2 –10 2* 1½* 257⁄16 6¾ 57⁄8 — — — — 1¼ 77⁄8 3 5½ 235 2½SAE8PK 2½ x 3 – 8 3* 2½* 2515⁄16 6¼ 5¼ — — — — 113⁄8
¼ 8
6 33⁄8 5 220
2½SAE9PK 2½ x 3 – 9 253⁄16 71⁄8 6 — — — — 7½ 2¾ 5½ 230 2½SAE10PK 2½ x 3 – 10 3 2½ 3½
3⁄8 77⁄8
2½SAE13PK 2½ x 3 – 13 255⁄16 87⁄8 75⁄8 — — — — 9 3 7½ 285 3SAE8PK 3 x 4 – 8 22¾ 61⁄4 53⁄8 — — — — ¼ 83⁄16 7 55⁄8 225 3SAE10PK 3 x 4 – 10 4 3 259⁄16 73⁄8 6½ — — — — 3¾ 8 7½ 5½ 240 3SAE13PK 3 x 4 – 13 257⁄16 91⁄2 81⁄8 — — — — 77⁄8 9
3 7½ 300
4SAE8PK 4 x 5 – 8 5 2513⁄16 67⁄8 5¾ — — — — 83⁄8 8 5 240 4SAE10PK 4 x 6 – 10
4 271⁄16 85⁄8 7½ — — — — 4½
3⁄8 83⁄8 8½ 31⁄8 7 280 4SAE13PK 4 x 6 – 13 6 2511⁄16 93⁄4 81⁄8 — — — — 81⁄8 9 3 7½ 315 4SAE16PK ■ 4 X 6 – 16 273⁄16 12¾ 11 115⁄16 9¾ 16 7 85⁄8 12 4 10½ 500 6SAE13PK ■ 6 X 8 – 13 8 6 2515⁄16 12¾ 10½ 23⁄8 7½ 13 5½ 5½ 83⁄8 11 3 8¾ 400 8SAE13PK ■ 8 x 10 – 13 10 8 273⁄16 14¾ 13 23⁄8 7½ 13 5½ 6¾ 85⁄8 12¾ 4 10 585 1¼SAE9½PK 1¼ x 1½ – 9½ 1½* 1¼* 265⁄16 61⁄8 57⁄16 – – – – 1¼ 1⁄8 8½ 8 3¼ 5½ 267 6SAE9½PK 6 x 8 – 9½ 8 6 3125⁄32 103⁄8 9¼ – – – – 61⁄16 ¼ 107⁄32 10½ 7 8¼ 499
Dimensions and WeightsPesos y dimensiones
*Denotes NPT connection. All other connections are for use with ANSI class 150 mating flanges.Dimensions in inches, weights in lbs. Do not use for construction purposes.* Indica conexión NPT Las demás conexiones deben usarse con bridas de contacto ANSI clase 150.Dimensiones en pulgadas, peso en libras. No utilizar para fines de construcción.■ Indicates “L” Group pump., ■ Indica una bomba Grupo “L”.
NOTE:1. All pumps shipped in horizontal dis-charge position. For other orientations, remove casing bolts, rotate to desired position, and tighten 3⁄8 - 16 casing bolts to 37 ft./lbs. torque., 1⁄2 - 13 casing bolts to 90 ft./lbs. torque.
2. Dimensions in inches, weight in pounds.3. Not to be used for construction purposes.
NOTA: 1. Todas las bombas se embarcan con la descarga en posición horizontal. Para otras orientaciones, retire los pernos de la carcasa, haga rotar la descarga hasta la posición de-seada y ajuste los 16 pernos de 3/8 de pulgada a una torsión de 37 pies/libra, y los 13 pernos de 1/2 pulgada a 90 pies/libra.2. Dimensiones en pulgadas, peso en libras.3. No utilizar con fines de construcción.
SAE #1 – 5
N NM
2 HOLES.56 DIA.
2 ORIFICIOS
X
K
Z R Y W
DCMAX.
DD
CP
DISCHARGEDESCARGA
SUCTIONSUCCIÓN
NPT DRAINDRENAJE NPT J
1.6251.624KEYWAY 3⁄16 x 3⁄8CHAVETERO 3⁄16 x 3⁄8
DIA.
SAE drive number is determined by the engine flywheel housing size.
El número del mando SAE se determina por el tamaño de la caja del volante del motor.
V1 V2
SAE # V1 V2
1, 3, 5 13¼ 1½ 2, 4 13 1¾
SAE Drive Dimensions and Weights Packed BoxPesos y dimensiones del mando SAE Caja prensaestopas
64
Ident. No. Pump Suction Discharge DC NPT Drain Weight (lbs.) Ident. No. Bomba Succión Descarga CP (Max.) DD J K M N R Drenaje W X Y Z Pesos NPT (libras) 1½SAE10MS 1½ x 2 –10 2* 1½* 229⁄16 63⁄4 57⁄8 — — — — 1¼ 5 3 5½ 235 2½SAE8MS 2½ x 3 – 8 3* 2½* 231⁄16 61⁄4 51⁄4 — — — — 113⁄16
¼ 51⁄8
6 33⁄8 5 220
2½SAE9MS 2½ x 3 – 9 225⁄16 71⁄8 6 — — — — 7½ 2¾ 5½ 230 2½SAE10MS 2½ x 3 – 10 3 2½ 3½
3⁄8 5
2½SAE13MS 2½ x 3 – 13 227⁄16 87⁄8 75⁄8 — — — — 9 3 7½ 285 3SAE8MS 3 x 4 – 8 197⁄8 61⁄4 53⁄8 — — — — ¼ 55⁄16 7 55⁄8 225 3SAE10MS 3 x 4 – 10 4 3 2211⁄16 73⁄8 6½ — — — — 3¾ 51⁄8 7½ 5½ 240 3SAE13MS 3 x 4 – 13 229⁄16 9½ 81⁄8 — — — — 5 9
3 7½ 300
4SAE8MS 4 x 5 – 8 5 2215⁄16 67⁄8 5¾ — — — — 5½ 8 5 240 4SAE10MS 4 x 6 – 10 4 245⁄16 85⁄8 7½ — — — — 4½
3⁄8 5½ 8½ 31⁄8 7 280 4SAE13MS 4 x 6 – 13 6 2213⁄16 9¾ 81⁄8 — — — — 5¼ 9 3 7½ 315 4SAE16MS ■ 4 x 6 – 16 273⁄16 12¾ 11 17⁄8 93⁄4 16 7 85⁄8 12 4 10½ 500 5SAE13MS ■ 6 x 8 – 13 8 6 2515⁄16 12¾ 10½ 23⁄8 7½ 13 5½ 5½ 83⁄8 11 3 8¾ 400 8SAE13MS ■ 8 x 10 – 13 10 8 273⁄16 14¾ 13 23⁄8 7½ 13 5½ 63⁄4 85⁄8 12¾ 4 10 585 1¼SAE9½MS 1¼ x 1½ – 9½ 1½* 1¼* 265⁄16 61⁄8 57⁄16 – – – – 1¼ 1⁄8 8½ 8 3¼ 5½ 265 6SAE9½MS 6 x 8 – 9½ 8 6 3125⁄32 103⁄8 9¼ – – – – 61⁄16 ¼ 107⁄32 10½ 7 8¼ 497
Dimensions and WeightsPesos y dimensiones
*Denotes NPT connection. All other connections are for use with ANSI class 150 mating flanges.Dimensions in inches, weights in lbs. Do not use for construction purposes.* Indica conexión NPT Las demás conexiones deben usarse con bridas de contacto ANSI clase 150.Dimensiones en pulgadas, peso en libras. No utilizar para fines de construcción.■ Indicates “L” Group pump., ■ Indica una bomba Grupo “L”.
NOTE:1. All pumps shipped in horizontal dis-charge position. For other orientations, remove casing bolts, rotate to desired position, and tighten 3⁄8 - 16 casing bolts to 37 ft./lbs. torque., 1⁄2 - 13 casing bolts to 90 ft./lbs. torque.
2. Dimensions in inches, weight in pounds.3. Not to be used for construction purposes.
NOTA: 1. Todas las bombas se embarcan con la descar-ga en posición horizontal. Para otras orientacio-nes, retire los pernos de la carcasa, haga rotar la descarga hasta la posición deseada y ajuste los 16 pernos de 3/8 de pulgada a una torsión de 37 pies/libra, y los 13 pernos de 1/2 pulgada a 90 pies/libra.2. Dimensiones en pulgadas, peso en libras.3. No utilizar con fines de construcción.
SAE #1 – 5
N NM
2 HOLES.56 DIA.
2 ORIFICIOS
X
K
Z R Y W
DCMAX.
DD
CP
DISCHARGEDESCARGA
SUCTIONSUCCIÓN
NPT DRAINDRENAJE NPT J
1.6251.624
KEYWAY 3⁄16 x 3⁄8CHAVETERO 3⁄16 x 3⁄8
DIA.
SAE drive number is determined by the engine flywheel housing size.
El número del mando SAE se determina por el tamaño de la caja del volante del motor.
V1 V2
SAE # V1 V2
1, 3, 5 13¼ 1½ 2, 4 13 1¾
SAE Drive Dimensions and Weights Mechanical SealDimensiones y pesos del mando SAE
Goulds PumpsAg. / Irrigation
65
Notes, Notas
66
Notes, Notas
Goulds PumpsAg. / Irrigation
67
Notes, Notas
68
Specifications
Capacities to: 1600 GPM (363 m3/hr) at 3500 RPM4500 GPM (1020 m3/hr) at 1750 RPM
Heads to: 490 feet TDH (150 m) at 3500 RPM300 feet TDH (90 m) at 1750 RPM
Working pressure to: 175 PSIG (12 bars)
Suction pressure to: 100 PSIG (7 bars)
Maximum temperature to: 212°F (100°C) with standard seal or 250°F (121°C) with optional seal.
Motor: NEMA standard JM frame or T-frame for mechanical seal, JP or T-frame for packed box. Open drip proof, totally enclosed fan cooled and explosion proof enclosures available. Single phase (115/230 V), ½-3 HP, (230 V) 5-7½ HP, and three phase (208 – 230/460 V) 2 – 150 HP are available at 1750 or 3500 RPM.
Direction of Rotation: Clockwise viewed from motor end.
Especificaciones
Capacidad hasta:1600 GPM (363 m 3/hr) a 3500 RPM4500 GPM (1020 m 3/hr) a 1750 RPM
Cargas hasta:490 pies (150 m) carga dinámica total a 3500 RPM300 pies (90 m) carga dinámica total a 1750 RPM
Presión de operación hasta:75 PSIG (12 bars)
Presión de succión hasta:100 PSIG (7 bars)
Temperatura máxima:212 °F (100 °C) con sello estándar o250 °F (121 °C) con sello optativo.
Motor:NEMA JM estándar en el modelo 3656 y bastidor NEMA T estándar en el modelo 3756 con sello mecánico, bastidor JP o T para caja prensaestopas. Las cubiertas disponibles son: abierta a prueba de filtración, totalmente encerrada con enfriamiento por ventilador y a prueba de explosiones. Motores monofásicos (115/230 V), ½-3 HP (230 V) 5-7½ HP, y trifásicos (208 – 230/460 V) 2 – 150 HP disponibles a 1750 ó 3500RPM.
Dirección de rotación:Dextrorsa (sentido de las agujas del reloj) cuando se mira desde el extremo del motor.
• Booster service
• Spraying systems
• Irrigation
• Water circulation
• Liquid transfer
• General purpose pumping
• Servicio de refuerzo
• Sistemas de rociado
• Sistemas de riego
• Circulación de agua
• Transferencia de líquidos
• Aplicaciones de bombeo en general
Typical Applications Aplicaciones típicas
ITTITT 2881 East Bayard Street, Seneca Falls, NY 13148 Phone: (315) 568-7123 • Fax: (315) 568-7973
www.goulds.com
Goulds Pumps is a registered trademark of ITT Corporation. ITT, the Engineered Blocks Symbol and Engineered for Life are registered trademarks of ITT Manufacturing Enterprises, Inc.
Copyright © 2009 ITT Corporation BAGFLO June, 2009 Printed in U.S.A.SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Engineered for life