b. Push Button
-
Upload
nabil-shaikh -
Category
Documents
-
view
212 -
download
0
Transcript of b. Push Button
-
8/18/2019 b. Push Button
1/1
35mm
7mm
2mm
If stainless steel units are to be fitted inareas where they may be subjected todeliberate attack they should berecessed below the surface of the wall.A cavity should be constructed asshown . The inner cavity should be 76 x76 (mm) to a depth of at least 42mm.The second cavity should be 91 x 91(mm) and approx 7mm deep. Thegalvanised socket box should be fitted
with two wood screws and suitable wallplugs to ensure that the box is totallysecure. The cable entry should be eitherrear or side entry. For iniital testing andcommissioning use conventional M3.5countersunk fixing screws to secure thecall point. When it has been establishedthat the system is working correctlyreplace these screws with securityscrews. A gap filling epoxy cementshould be used to form a seal betweenthe stainless steel plate and the wall.
S0610 Mounting SpacerAlthough Stainless steel units are generallyintended for flush fitting using the galvanisedbox provided they can be surface mounted usingthe S0610 mock stainless steel mountingspacer.The galvanised box should be mounted in therequired position and the cable entries made.The S0610 spacer is then placed over the box,the relevant terminations made off and the platescrewed down on to the box. The spacer istherefore gripped between the wall and the
plate.
Epoxy Cement
NO
COM
NC
Bz -ve
-ve LED+ve
-veLED+ve
Blue
Yellow
White
Red
Red
Black
Black
Dwg No. 60068:0 Iss 3 Feb 2008
Products covered by this installation instruction
Stock No Description Material Printing/EngravingS1605P Button and Plastic Press to CallS1605S Button and Stainless steel Press to CallS1605TC Button and LED Stainless steel (Own Text 46 chars)S1606S Button Stainless steel Press to ExitS1606TC Button Stainless steelS1607S Button Stainless steel Press to EnterS1608P Button Plastic Press to Reset
S1608SS1614TC Two LEDs Stainless steelS1615TC Button & two LEDs Stainless steelS1636RS Jumbo LED (Red) Stainless steelS1636GSS1678RS Jumbo LED (Red) & Sounder Stainless steel
All the above items are dimensionally compatible with single gang BS4662 fittings. Theyare designed for operation on 12 volts DC. NOT to be used on 240v mains. All aresupplied with a mounting box, surface plastic pattress box or a 34 mm deep galvanisedflush box in the case of the stainless steel units.
LEDLED
(Own Text 18 chars)
Button Stainless steel Press to Reset(Own Text 18 chars)(Own Text 18 chars)
Jumbo LED (Green) Stainless steel
S0610 Mounting Spacer Galvanised BoxStainless Steel Plate
On the stainless steel versions of this product the jumbo LED is supplied loose to preventdamage in transit. It should be clipped into place on installation.
All LEDs follow the above
Jumbo LEDs follow this convention
and where fitted a sounder followsthis convention
WARNING! The stainless steel version may have sharp edges. This isnot a problem post installation but please exercise care when handlingand during installation.
All Pushbuttons or Keyswitches followthe above colour convention
Hoyles Electronic Developments LtdSandwash Close, Rainford Ind Est, Rainford, St Helens, WA11 8LY.
T.01744 886600 F.01744 886607 [email protected] W.www.hoyles.com