B: METROLOGY DISCIPLINE AND LEVEL OF CERTIFICATION … · 2012. 2. 13. · Torque G08-1 G08-2...

NLA-MC-F-01-07

January 2012 NLA Page 1 of 28

APPLICATION FOR THE CERTIFICATION OF METROLOGISTS

(For office use only)

REFERENCE No.

C

A: APPLICANT DETAILS

Date Title New Application

Renewal

Up Grade

Names

Surname

Position / Function

Physical Address

Tel

Postal Address

Tel

Cell E-Mail ID No.

B: METROLOGY DISCIPLINE AND LEVEL OF CERTIFICATION SOUGHT

Trainee Metrologist

Metrologist

Expert Metrologist

Trainee

Metrologist Metrologist Expert

Metrologist Total No of Years in

Metrology ►

Training Records

Section D

Section D

Section D

Please take Note!

All applicants must complete and submit Section A, B, C, D, E, G00

and F-“Code of Conduct”.

Trainee metrologist must also submit a training schedule

supported by employer.

Metrologist and Expert Metrologist must mark the Metrology discipline and must complete the appropriate section(s) of “G---” identified in the

table on the left,

e.g. Dimension G01-1 and/or G01-2

Mass G03-1 and/or G03-2 Etc.

Radio Frequency, Fibre Optics and

other discipline(s) are subject to approval by the scheme and evaluation

Committee.

Dimensional

▲ Id

entif

y w

hich

dis

cipl

e(s)

of M

etro

logy

▲

G01-1

G01-2

Electrical

G02-1

G02-2

Mass

G03-1

G03-2

Temperature

G04-1

G04-2

Humidity

G05-1

G05-2

Pressure

G06-1

G06-2

Force

G07-1

G07-2

Torque

G08-1

G08-2

Hardness

G09-1

G09-2

Time & Frequency

G10-1

G10-2

Radio Frequency

G11-1

G11-2

Fibre Optics

G12-1

G12-2

Other discipline(s)

G13-1

G13-2

Specify other discipline(s):-

NLA-MC-F-01-07


C: EDUCATION AND QUALIFICATIONS

Year School (Complete only if no higher education) Level e.g. matric

Year College/Technikon/University Qualification e.g. Degree, Diploma or Certificate or Certificate or highest level obtained

D: Additional Relevant Training e.g. courses (Quality &Technical) list all short duration courses

Please submit certificate of completion or certific ate of attendance. If the theoretical requirement was not obtained via an NLA Course, please submit evidence of

course syllabus, content, provider or lectures and criteria’s use for successful completion.

Year Training Provider Course attended and/or certificate obtained Duration

ISO/IEC 17025 System Course - (Compulsory)

Introduction to Metrology - (Compulsory)

Uncertainty of Measurement - (Compulsory)

Procedure Writing

Method Validation

Report Writing

E: Current membership of Professional Institutions

Year Institution Membership Grade

Member of the NLA Y N Corporate Membership

Individual Membership

NLA-MC-F-01-07


F: CODE OF CONDUCT

In applying for certification with the NLA Metrologists Certification scheme, I recognise the important role that laboratories play in performing tests and calibrations for industry and consumers in South Africa and the SADC region in general. I hereby commit myself to the highest ethical and professional standards and agree to the following :-

• to accept responsibility for the performance of the tests and calibrations carried out by myself and to respect the confidentiality thereof;

• to promptly advise clients of measurement results which indicate a potential or inherent environmental, health, safety, or any other related risk with the product or material submitted by the client;

• to avoid real or perceived conflicts of interest whenever possible and to disclose them to the affected parties when they do exist;

• to be honest and realistic in stating claims or estimates based on available data; • to reject bribery in all its forms; • not to knowingly falsify or alter measurement data, provide misleading

information or conduct work below the standard expected by regulations or general industry expectations;

• to improve the understanding of technology and the appropriate application thereof together with any potential consequences;

• to maintain and improve technical competence and to undertake tasks only if qualified by training or experience or after full disclosure of pertinent limitations;

• to seek, accept and offer honest criticism of technical work performed and to acknowledge, correct errors and to properly credit the contributions of others;

• to treat fairly all persons regardless of such factors as race, religion, gender, disability, age or national origin;

• to avoid injuring others, their property, reputation or employment by false or malicious action;

• to assist colleagues and co-workers with their professional development; • to protect and preserve the corporate image and reputation of the NLA; • to protect and preserve the assets both physical and intellectual of the NLA; • to support all members of the NLA in following this code of conduct;

I understand that the NLA may withdraw my certification with immediate effect, should I be found in contravention of any of the above principles.

………………………… ……………………………… ………………….. Printed Name Signature Date

NLA-MC-F-01-07


G00: EXPERIENCE (Please indicate detail of relevant experience for approval sought)

Note! As an option an applicants may submit a CV.

The CV must be clear, unambiguous and detail all information / requirements

Date (from)

Date (to)

Name of Employer and nature of Business (last five positions, most recent first)

Position held and detail of work performed (Indicate experience in performing technical

work, quality assurance)

Use addition sheet(s) if required – (CV optional, s ee note above)

Additional Motivation (Information pertinent to this application)

I hereby declare that the above information is a true statement of facts.

Name:

Signature:

Date:

Application is supported by Head of Lab or Registered Metrologist

Name: Signature:

Position:

Date:

NLA-MC-F-01-07


G01-1 REGISTRATION as a METROLOGIST (Dimensional)

Practical Calibration Tasks & Requirements. Portfolio of Work / Evidence successfully completed in a laboratory, items marked with (*) are compulsory.

One (1) Calibration per task to be entered. OPTIONAL - Only one (1) Inter-Laboratory Comparison (ILC)

is sufficient to be entered. All info (data) entered shall not be not older than 5 years .

Number of Years of Experience in Dimensional Metrology Please Submit

Evidence Registered as a “Trainee Metrologist” (If yes state registration number)

Holder of a SANAS Dimensional Certificate of Competence Y N

Part 1 NLA - Dimensional Metrology Course or equivalent (as entered in Section D) Y N

Typical Calibration Tasks. (Add additional supporting tasks if desired) Equipment Model Cert No (for Office use only)

Participated ILC (Details or Report No.)

(for Office use only)

* Calibration of Vernier Calipers and Accessories

* Reading of Analogue Scales - (Verniers & Micrometers)

* Care and cleaning of Basic Hand Measurement Tools – (Including Gauge Blocks)

* Calibration of Digital In & Outside Micrometer and Accessories

Calibration of Digital In & Outside Tri-Micrometer and Accessories

* Calibration of Dial Gauges

* Measurement of Flatness using Monochromatic Light

* Calibration of Height Gauges

* Demonstrate an understanding of Thermal Expansion of Dimensional Measuring Equipment

► Certificates and Data for all tasks including deta iled calculation of the Uncertainty of Measurements must be available and submitted if requested ◄

I hereby declare that the above information is a true reflection of my experience.

Name: Signature:

Date:


Name: Signature:

Position:

NLA-MC-F-01-07


G01-2 REGISTRATION as an EXPERT METROLOGIST (Dimensional)

Practical Calibration Tasks & Requirements. Portfolio of Work / Evidence successfully completed in a laboratory, items marked with ( *) are compulsory.

One (1) Calibration per task to be entered. At least one (1) Inter-Laboratory Comparison (ILC) is

mandatory to be entered. All info (data) entered shall not be not older than 5 years .

Number of Years of Experience in Dimensional Metrology Please Submit

Evidence Registered as a “Dimensional Metrologist” (If yes state registration number)

Holder of a SANAS Dimensional Certificate of Competence Y N

Part 2 NLA - Dimensional Metrology Course or equivalent (as entered in Section D) Y N

Typical Calibration Tasks. (Add additional supporting tasks if desired) Equipment Model Cert No


Participated ILC (Detail or Report No.)


* All tasks compulsory for Dimensional Metrologist Level (See Form G01-1) completed Y N

* Calibration of Plain, Screw and Taper Ring Gauges

* Calibration of Plain, Screw Plug Gauges

* Calibration of Cylindrical Taper Gauge

* Calibration of Gauge Blocks and Accessories

* Calibration of Optical Projectors

* Calibration of Surface Plate or Table

► Certificates and data for all tasks including a de tailed calculation of the Uncertainty of Measuremen ts must be available and submitted if requested ◄


Name: Signature:

Date:

Application is supported by Head of Lab or Registered Expert Metrologist

Name: Signature:

Position:

NLA-MC-F-01-07


G02-1 REGISTRATION as a METROLOGIST (Electrical - DCLF)




Number of Years of Experience in Electrical - DCLF Metrology Please Submit


Holder of a SANAS Electrical - DCLF Certificate of Competence Y N

Part 1 NLA – Electrical - DCLF Metrology Course or equivalent (as entered in Section D) Y N




* AC-DC Voltage Meters ≥ 4½ Digital Multimeter

* AC-DC Voltage Sources Typically ± 100 ppm

* AC-DC Current Meter ≥ 4½ Digital Multimeter

* AC-DC Current Sources Typically ± 100 ppm

* Resistance Meters ≥ 4½ Digital Multimeter

* Resistances Sources using Volt-drop Method Typically ± 200 ppm

* Resistances Sources substitution Method 2 & 3 wire Typically ± 500 ppm

* Calibration of Meggers - (Insulation Tester) Typically ± 3%

* Calibration of Current Clamp Meters Typically ± 3%

Calibration of High Voltage Probes Typically ± 3%



Name: Signature:

Date:


Name: Signature:

Position:

NLA-MC-F-01-07


G02-2 REGISTRATION as an EXPERT METROLOGIST (Electrical - DCLF)




Number of Years of Experience in Electrical - DCLF Metrology Please Submit

Evidence Registered as a “Electrical - DCLF Metrologist” (If yes state registration number)

Holder of a SANAS Electrical - DCLF Certificate of Competence Y N

Part 2 NLA – Electrical - DCLF Metrology Course or equivalent (as entered in Section D) Y N





* All tasks compulsory for Electrical - DCLF Metrologist Level (See Form G02-1) completed Y N

* AC-DC Voltage Meters ≥ 6½ Digital Multimeter

* AC-DC Voltage Sources Typically ± 10 ppm

* AC-DC Current Meter ≥ 6½ Digital Multimeter

* AC-DC Current Sources Typically ± 10 ppm

* Resistance Meters ≥ 6½ Digital Multimeter

* Capacitance Typically ± 0,05%

* Inductance Typically ± 0,05%

* LCR Meters Typically ± 0,05%

Oscilloscopes ≤ 250 MHz Voltage / Current / Time-Base / Bandwidth Typically ± 0,5%

Basic Frequency Measurements Range 0,01 Hz - 250 MHz Typically ± 50 ppm

AC / DC Power & Energy Range ≥ 1 kW - PF 1 & 0,5 Typically ± 0,5 %

Electrical Simulation TC & RTD - (Using Internal & External CJC) ± 0,2ºC



Name: Signature:

Date:


Name: Signature:

Position:

NLA-MC-F-01-07


G03-1 REGISTRATION as a METROLOGIST (Mass)




Number of Years of Experience in Mass Metrology Please Submit


Holder of a SANAS Mass Certificate of Competence Y N

NLA - Mass Metrology Course or equivalent (as entered in Section D) Y N




* Calibration of a Digital Self Indicating Weighing Instrument (Typical industrial weighing instrument)

* Calibration of Analytical Laboratory Digital Balance

* Calibration of a non-self-indicating Mechanical Weighing Instrument (Triple beam balance, steelyard, etc.)

* Calibration of a Set of Weights ≤ 500 g

* Calibration of a Set of Weights ≥ 1 kg

* Demonstrate an understanding of magnetic influence on mass measurement (e.g. Experimental results)



Name: Signature:

Date:


Name: Signature:

Position:

NLA-MC-F-01-07


G03-2 REGISTRATION as an EXPERT METROLOGIST (Mass)




Number of Years of Experience in Mass Metrology Please Submit

Evidence Registered as a “Mass Metrologist” (If yes state registration number)

Holder of a SANAS Mass Certificate of Competence Y N

NLA - Mass Metrology Course or equivalent (as entered in Section D) Y N





* All tasks compulsory for Mass Metrologist Level (See Form G03-1) completed Y N

* Calibration of Weights using Orthogonal Design

* Demonstrate an understanding of Buoyancy and Gravity Corrections

* Calibration of Microbalances

* Gravimetric Measurement of Volume (Micro-Pipettes, including Calculation of Mass/Volume corrections)

* Gravimetric Measurement of Volume (Volumetric glassware, and/or Metal measures, including Calculation of Mass/Volume corrections)

* Determine the Density of a Solid

* Determine the Density of a Liquid

* Certification of Weights against OIML Requirements



Name: Signature:

Date:


Name: Signature:

Position:

NLA-MC-F-01-07


G04-1 REGISTRATION as a METROLOGIST (Temperature)




Number of Years of Experience in Temperature Metrology Please Submit


Holder of a SANAS Temperature Certificate of Competence Y N

NLA - Temperature Metrology Course or equivalent (as entered in Section D) Y N




* Preparation of an ice point

* Calibration of a Liquid in Glass Thermometer Resolution ≤ 0,1ºC

* ELC Corrections

* Calibration of Digital Thermometer or Thermometry System including Probe and Readout Device

* TC tables and CJC calculations

* TC Calibration - (Base Metal) Accuracy ≥ 0,5ºC

* RTD’s, PT100, Thermistors, Semiconductors, etc. Calibration, 2 / 3 / 4 wire systems Accuracy ≥ 0,1ºC

* Electrical Simulation TC & RTD Calibration Devices

* Calibration of Digital Thermometer - (Electrical Equivalent)



Name: Signature:

Date:


Name: Signature:

Position:

NLA-MC-F-01-07


G04-2 REGISTRATION as an EXPERT METROLOGIST (Temperature)




Number of Years of Experience in Temperature Metrology Please Submit

Evidence Registered as a “Temperature Metrologist” (If yes state registration number)

Holder of a SANAS Temperature Certificate of Competence Y N

NLA - Temperature Metrology Course or equivalent (as entered in Section D) Y N





* All tasks compulsory for Temperature Metrologist Level (See Form G04-1) completed Y N

Calibration of Isothermal Media – (Sterilizer)

Calibration of Isothermal Media – (Autoclave)

* TC Calibration - (Noble Metal) Accuracy ≤ 1ºC

* RTD Calibration Accuracy ≤ 0,1ºC

Radiation Thermometry

* Temperature Installations – (Ovens, Liquid Baths, etc.) ≥ 100ºC including measuring techniques

* Temperature Installations – (Fridges, Freezers) ≤ 5ºC including measuring techniques

* Calibration of Dry Blocks

Surface Temperature Probes;

Heat Stress (WBGT) Monitors



Name: Signature:

Date:


Name: Signature:

Position:

NLA-MC-F-01-07


G05-1 REGISTRATION as a METROLOGIST (Humidity)




Number of Years of Experience in Humidity Metrology Please Submit


Holder of a SANAS Humidity Certificate of Competence Y N

NLA - Humidity Metrology Course or equivalent (as entered in Section D) Y N




* Calibration of Thermo-Hygrometers

* Calibration of Thermo-Hygrographs

* Calibration of Temperature Measurement Sensor and/or Recorder on Thermo-Hygrometer

* Calibration of Humidity Salts

* Demonstrate an understanding of the use and care of a Humidity Standards - (Salts) (Including knowledge of MSDS and hazards associated with humidity salts)



Name: Signature:

Date:


Name: Signature:

Position:

NLA-MC-F-01-07


G05-2 REGISTRATION as an EXPERT METROLOGIST (Humidity)




Number of Years of Experience in Humidity Metrology Please Submit

Evidence Registered as a “Humidity Metrologist” (If yes state registration number)

Holder of a SANAS Humidity Certificate of Competence Y N

NLA - Humidity Metrology Course or equivalent (as entered in Section D) Y N





* All tasks compulsory for Humidity Metrologist Level (See Form G05-1) Y N

* All tasks compulsory for Temperature Metrologist Level (See Form G04-1) Y N Attach Form G04-1

* Calibration of Dew-Point Hygrometer

Measurement of Water Activity

* Calibration of Environmental Chambers

* Calibration of Humidity Loggers



Name: Signature:

Date:


Name: Signature:

Position:

NLA-MC-F-01-07


G06-1 REGISTRATION as a METROLOGIST (Pressure)




Number of Years of Experience in Pressure Metrology Please Submit


Holder of a SANAS Pressure Certificate of Competence Y N

NLA - Pressure Metrology Course or equivalent (as entered in Section D) Y N




* Calibration of Bourdon Tube type Pressure Gauges (Including the adjustment thereof to correct for zero, span and linearity errors)

* Use and care of a Pressure Balance as a Standard in the Pressure Laboratory (Including calculation of Pressure from first principles)

* Use and care of a Liquid Manometer as a Standard in the Pressure Laboratory (Including the calculation of applied Pressure from first principles)

* Calibration of Pressure switches

* Calibration of Pressure transmitters with electrical output - (mA, V, Ω, etc.)



Name: Signature:

Date:


Name: Signature:

Position:

NLA-MC-F-01-07


G06-2 REGISTRATION as an EXPERT METROLOGIST (Pressure)




Number of Years of Experience in Pressure Metrology Please Submit

Evidence Registered as a “Pressure Metrologist” (If yes state registration number)

Holder of a SANAS Pressure Certificate of Competence Y N

NLA - Pressure Metrology Course or equivalent (as entered in Section D) Y N





* All tasks compulsory for Pressure Metrologist Level (See Form G06-1) completed Y N

* Calibration of Barometers

* Calibration of Vacuum Gauges

* Calibration of Pressure Calibrators including basic Electrical output/input - (mA, V, Ω)

* Calibration of Pressure Balances by Cross Floating

* Calibration of Pressure Balance Weights (Including conversion from Mass units to units of Pressure)



Name: Signature:

Date:


Name: Signature:

Position:

NLA-MC-F-01-07


G07-1 REGISTRATION as a METROLOGIST (Force)




Number of Years of Experience in Force Metrology Please Submit


Holder of a SANAS Force Certificate of Competence Y N

NLA - Force Metrology Course or equivalent (as entered in Section D) Y N




* Calibration of Load Cells using weights

* Calibration of Load Cells by comparison Accuracy ± 0,5%

* Calibration of Force Machines

* Demonstrate the use and understanding of the Polynomial function for a calibrated Load Cell



Name: Signature:

Date:


Name: Signature:

Position:

NLA-MC-F-01-07


G07-2 REGISTRATION as an EXPERT METROLOGIST (Force)




Number of Years of Experience in Force Metrology Please Submit

Evidence Registered as a “Force Metrologist” (If yes state registration number)

Holder of a SANAS Force Certificate of Competence Y N

NLA - Force Metrology Course or equivalent (as entered in Section D) Y N





* All tasks c ompulsory for Force Metrologist Level (See Form G07-1) completed Y N

* Experience of Torque or Hardness - (Specify) All tasks compulsory for Torque Metrologist Level (See Form G08-1) Y N

Attach Form G08-1 or G09-1

or All tasks compulsory for Hardness Metrologist Level (See Form G09-1) Y N

* Calibration of Load Cells Accuracy < 0,5%

Calibration of force Readout Devices

* Generation of Polynomial functions for Load Cells

* Calibration of Tensile Machines including Creep / Speed and Extensometers

* Demonstrate an understanding of Material Testing - (Tests such as Tensile, Impact etc.)



Name: Signature:

Date:


Name: Signature:

Position:

NLA-MC-F-01-07


G08-1 REGISTRATION as a METROLOGIST (Torque)




Number of Years of Experience in Torque Metrology Please Submit


Holder of a SANAS Torque Certificate of Competence Y N

NLA - Torque Metrology Course or equivalent (as entered in Section D) Y N




* Calibration of Torque Tools - (Wrenches)

* Calibration of Torque Tools - (Screwdrivers);

* Demonstrate an understanding of the fundamentals of Torque Measurement (Including detailed Measurement Uncertainty analysis)



Name: Signature:

Date:


Name: Signature:

Position:

NLA-MC-F-01-07


G08-2 REGISTRATION as an EXPERT METROLOGIST (Torque)




Number of Years of Experience in Torque Metrology Please Submit

Evidence Registered as a “Torque Metrologist” (If yes state registration number)

Holder of a SANAS Torque Certificate of Competence Y N

NLA - Torque Metrology Course or equivalent (as entered in Section D) Y N





* All tasks compulsory for Torque Metrologist Level (See Form G08-1) completed Y N

* Experience of Force or Hardness - (Specify) All tasks compulsory for Force Metrologist Level (See Form G07-1) Y N


or All tasks compulsory or Hardness Metrologist Level (See Form G09-1) Y N

* Calibration of Torque Transducers

* Generate Torque using Beam & Weights

* Generate and use a Polynomial function for the Interpolation of a Torque Transducer



Name: Signature:

Date:


Name: Signature:

Position:

NLA-MC-F-01-07


G09-1 REGISTRATION as a METROLOGIST (Hardness)




Number of Years of Experience in Hardness Metrology Please Submit


Holder of a SANAS Hardness Certificate of Competence Y N

NLA - Hardness Metrology Course or equivalent (as entered in Section D) Y N




* Calibration of Hardness Machines using Hardness Blocks - (Indirect Method)

* Calibration of Hardness Blocks by comparison

* Demonstrate an understanding of Hardness Scales - (e.g. Rockwell, Vickers, Brinell, etc.)



Name: Signature:

Date:


Name: Signature:

Position:

NLA-MC-F-01-07


G09-2 REGISTRATION as an EXPERT METROLOGIST (Hardness)




Number of Years of Experience in Hardness Metrology Please Submit

Evidence Registered as a “Hardness Metrologist” (If yes state registration number)

Holder of a SANAS Hardness Certificate of Competence Y N

NLA - Hardness Metrology Course or equivalent (as entered in Section D) Y N





* All tasks compulsory for Hardness Metrologist Level (See Form G09-1) completed Y N

* Experience of Force or Torque - (Specify) All tasks compulsory for Force Metrologist Level (See Form G07-1) Y N


or All task s compulsory for Torque Metrologist Level (See Form G08-1) Y N

* Calibration of Hardness Machines in terms of first principles - (Direct Method)

* Inspection of Indenters in terms of requirements

* Demonstrate an understanding of Materials Tests - (e.g. Charpy, Izod, etc.)



Name: Signature:

Date:


Name: Signature:

Position:

NLA-MC-F-01-07


G10-1 REGISTRATION as a METROLOGIST (Time & Frequency – T&F)




Number of Years of Experience in Time & Frequency Metrology Please Submit


Holder of a SANAS Time & Frequency Certificate of Competence Y N

NLA – Time & Frequency Metrology Course or equivalent (as entered in Section D) Y N




* Calibration of the Frequency Generator or Source

* Generation of a Frequency with known Accuracy

* Calibration of Frequency Counter

* Calibrate a Time Interval Source - (Uncertainty > 1 µs)

* Generate a Time Interval with known Accuracy - (Uncertainty > 1 µs)

Calibrate the Phase Angle between two Periodic Waves

Calibration of Stopwatches

Calibration of Tachometers

Calibrate an Oscilloscope with a Bandwidth ≤ 250 MHz (Voltage / Current / Time-Base / Bandwidth Typically ± 0,5%)



Name: Signature:

Date:


Name: Signature:

Position:

NLA-MC-F-01-07


G10-2 REGISTRATION as an EXPERT METROLOGIST (Time & Frequency – T&F)

Practical Calibration Tasks & Requirements. Portfolio of Work / Evidence successfully completed in a

laboratory, items marked with (*) are compulsory. One (1) Calibration per task to be entered.

At least one (1) Inter-Laboratory Comparison (ILC) is mandatory to be entered.

All info (data) entered shall not be not older than 5 years .

Number of Years of Experience in Time & Frequency Metrology Please Submit

Evidence Registered as a “Time & Frequency Metrologist” (If yes state registration number)

Holder of a SANAS Time & Frequency Certificate of Competence Y N

NLA – Oscilloscope Metrology Course or equivalent (as entered in Section D) Y N

NLA – Time & Frequency Metrology Course or equivalent (as entered in Section D) Y N





* All tasks compulsory for T&F Metrologist Level (See Form G10-1) completed Y N

* Demonstrate the maintenance (monitoring) of a Frequency Standard using GPS, determine and apply corrections to provide Frequency Traceability in a laboratory

* Calibration and characterisation of a Local, Fixed Frequency, Standard - (Oscillator)

* Calibration of a High accuracy Frequency Counter

* Calibrate a High Accuracy Time Interval Source - (Uncertainty ≤ 1 µs)

Oscillator phase calibration

Calibrate an Oscilloscope with a Bandwidth >250 MHz

Calibrate a Pulse for Rise and Fall Time - (Characterization)



Name: Signature:

Date:


Name: Signature:

Position:

NLA-MC-F-01-07


G11-1 REGISTRATION as a METROLOGIST (Radio Frequency - RF)




Number of Years of Experience in Radio Frequency Metrology Please Submit


Holder of a SANAS Radio Frequency Certificate of Competence Y N

NLA – Radio Frequency Metrology Course or equivalent (as entered in Section D) Y N




* Calibration of a Power Sensor

* Calibration of a Fixed Attenuator

* Calibration of a Step Attenuator

* Calibration Voltage Reflection Coefficient of an Offset or Termination



Name: Signature:

Date:


Name: Signature:

Position:

NLA-MC-F-01-07


G11-2 REGISTRATION as an EXPERT METROLOGIST (Radio Frequency - RF)




Number of Years of Experience in Radio Frequency Metrology Please Submit

Evidence Registered as a “Radio Frequency Metrologist” (If yes state registration number)

Holder of a SANAS Radio Frequency Certificate of Competence Y N

NLA – Radio Frequency Metrology Course or equivalent (as entered in Section D) Y N





* All tasks compulsory for RF Metrologist Level (See Form G11-1) completed Y N

* Calibration of a Modulation Meter - (AM, FM, QM, etc.)

Calibration of a RF Millivolt Meters

* Calibration of a Spectrum Analysers

* Calibration of a Return Loss Bridge or Directional Coupler

* Calibration of Power Splitters

Calibration of 75 Ω Devices

* Demonstrate an understanding of the use of a Scalar or Vector Network Analyser



Name: Signature:

Date:


Name: Signature:

Position:

NLA-MC-F-01-07


G12-1 REGISTRATION as a METROLOGIST (Fibre Optics)




Number of Years of Experience in Fibre Optics Metrology Please Submit


Holder of a SANAS Fibre Optics Certificate of Competence Y N

NLA – Fibre Optics Metrology Course or equivalent (as entered in Section D) Y N




* Calibration of a Fibre Optic Power Meter

* Calibration of Fibre Length

* Calibration of Wavelength of a Laser Source

* Calibration of Attenuation of a Fibre Optic Component



Name: Signature:

Date:


Name: Signature:

Position:

NLA-MC-F-01-07


G12-2 REGISTRATION as an EXPERT METROLOGIST (Fibre Optics)

Practical Calibration Tasks & Requirements. Portfolio of Work / Evidence successfully completed in a laboratory. (Items marked with * are compulsory)



Number of Years of Experience in Fibre Optics Metrology Please Submit

Evidence Registered as a “Fibre Optics Metrologist” (If yes state registration number)

Holder of a SANAS Fibre Optics Certificate of Competence Y N

NLA – Fibre Optics Metrology Course or equivalent (as entered in Section D) Y N





* All tasks compulsory for Fibre Optics Metrologist Level (See Form G12-1) completed Y N

* Calibration of OTDR - (Length, Attenuation, Reflectance)

* Calibration of a Wavelength Meter for Wavelength

* Calibration of an Optical Spectrum Analyser for Wavelength

Calibration of Fibre Characteristics (e.g. Polarisation mode dispersion, Chromatic dispersion, Non-linearity’s, Cut-off wavelength)

Calibration of attenuation of a Fibre Optic Cable

Calibration of Return Loss - (Pulsed and Continuous wave)

Calibration of a Polarisation Analyser

Characterisation of an Optical Pulse (e.g. Spectral Bandwidth, Power, Side mode Suppression, Pulse width )



Name: Signature:

Date:


Name: Signature:

Position:

B: METROLOGY DISCIPLINE AND LEVEL OF CERTIFICATION … · 2012. 2. 13. · Torque G08-1 G08-2...

Documents

Transcript of B: METROLOGY DISCIPLINE AND LEVEL OF CERTIFICATION … · 2012. 2. 13. · Torque G08-1 G08-2...