8/2/2019 Axxius800 Dual Port Ds3 Controller Rel2 0 Spec Sheet

1/3

The Dual-Port DS3 Controller Card is a key compo-

nent of the AxxiusTM 800 Access Integration

Platform, delivering a cost-effective, compact solu-

tion that supports advanced voice and data services

on a single platform, while turning previously wasted

bandwidth into new revenues.

Combined functionality with full 3/1/0 cross-connect capabilityThe Axxius 800 with a DS3 Controller replaces back-

to-back M13 multiplexers and provides 3/1/0 cross-

connect capability to groom DS1 and DS0 services.

It also offers service providers the ability to provide

fractional T1 and DS0 level services in a single plat-

form while continuing to fully utilize the available

DS3 bandwidth. In addition, it can operate as a DS3

add/drop multiplexer, delivering T1/FT1 tributaries to

remote cell sites or customer locations. With a DS3

Controller, the Axxius 800 supports up to 32 T1

ports. With two DS3 Controllers protection and

redundancy is achieved.

The DS3 Controller features two DS3 ports with inte-grated CSUs and a built-in, full, non-blocking 3/1/0

cross-connect matrix. It provides connectivity

between the Controllers two DS3 ports and any of

the eight Service Card slots. The DS3 Controller also

connects to the Control Panel Interface Card for

physical termination of the on-board DS3 circuits

and access to the RS-232 and Ethernet management

interfaces.

Configuration and remote management func-tionality

The DS3 Controller has several local and remote

management options available. Front-panel LEDsquickly communicate alarm, system, and DS3 line

status. The Controller can be configured and man-

aged locally through the RS-232 or Ethernet man-

agement connections on the Control Panel Interface

Card using a Command Line Interface (CLI).

A number of remote management options are avail-

able to reduce truck roll costs for most maintenance

and troubleshooting activities. The in-band DS0

management channel on the Controller delivers 64

Kbps of remote access to the Axxius 800 without

incurring additional facility costs. Alternatively, a

separate Ethernet facility can be deployed to support

out-of-band SNMP network management. TheController can also be accessed through the V.34

dial-in modem connection from the Single-Channel

POTS Service Card with V.34 Modem.

Generate new voice and data services and revenues on a singleplatform while capitalizing on wasted bandwidth

Dual-Port DS3 Controller CardDual-Port DS3 Controller CardRelease 2.0For use in Axxius 800 PlatformPart Number: 740-0074

What makes the Axxius 800 with DS3 Controller Card different: Consolidates bandwidth delivery, grooming, and management functions of multiple boxes into one 2 RU

platform

Compact, single-box solution that allows service providers to optimize T1 access facilities and deliver

additional revenue-generating services at dramatically lower costs

Rescues up to 35% or more of network bandwidth commonly wasted at the cell site or when providing

fractional T1 service redistributes residual bandwidth improving network efficiency and maximizing leased

lines

Extends DCS capabilities to cell sites, POPs and COLOs, enabling previously unused DS0s to be used to

deliver revenue-generating services

Supports addition of new T1 services with existing T1 circuits

8/2/2019 Axxius800 Dual Port Ds3 Controller Rel2 0 Spec Sheet

2/3

DS3 ISDN BRI OCU-DP V.35 10/100Base-TX FXO RS-232 T1 ADPCMNx56/64K Ethernet (Asynch)

2 36 64 16 32 64 32 8

A x x i u s 8 0 0 P o r t C a p a c i t y w i t h D u a l D S 3 C o n t r o l l e r

Key features Supports 3/1/0 grooming for service delivery applications and distributes residual bandwidth to remote cell

sites or customer locations

Integrated 3/1/0 digital cross-connect for service grooming, restoration, and add/drop functions

Provides full, non-blocking 3/1/0 cross-connectivity between the DS3 ports and any of the eight Service

Card slots

Two DS3 ports and 3/1/0 digital cross-connect deliver bandwidth to the system service slots

Operating temperature range -40 F to 149 F (-40 C to 65 C)

Enables remote SNMP, or Telnet provisioning, monitoring, and testing of services and network conditions

Selectable test loopbacks for quick fault isolation

DS3 line redundancy configurable via craft executable command

Product Ordering Infor

Inside Sales Represe

inside-sales@carrieracce

800-365

303-218

5395 Pearl P

Boulder, Colorado

www.carrieracce

T e c h n i c a l s p e c i f i c a t i o n s f o r t h e A x x i u s 8 0 0 D u a l - P o r t D S 3 C o n t r o l l e r C a r d

Requirements: Axxius 800 Release 1.0 or higher to support the Dual-Port

DS3 Controller Axxius 800 Release 2.0 or higher to support all featureslisted

Product Includes: Built-in, non-blocking 3/1/0 digital cross-connect system Robbed-bit (voice) and clear-channel (data) signaling on the

same DS3 Integral dual DS3 ports that support drop-and-insert

applications RFC 2496 performance monitoring statistics: 96 15-minute

segments (24-hour period) Performance report messages Front-panel LED indicators for DS3 status, major and minor

alarms, and Alarm Cut-Off (ACO) status are located on theControl Panel Interface Card

Controller support for Quad-Port Terminal Server Router(TSR) Service Card code download through its Ethernetmanagement port

Configurations automatically stored in non-volatile memory SNMP agent, supporting MIB objects:- RFC 1213 (MIB-II)- RFC 1659 (V.35)- RFC 1907 (SNMPv2-MIB)- RFC 2011 (IP-MIB)- RFC 2233 (IF-MIB)- RFC 2494 (DS0-MIB)- RFC 2495 (DS1-MIB)- RFC 2496 (DS3-MIB)

Management: Local:

- RS-232 craft port interface drives up to a 50 ft (15.24 m)cable and provides a Command Line Interface (CLI) usingASCII terminal or PC with terminal emulation software, ormodem using XMODEM or PPP sessions

Remote:- 10/100Base-TX Ethernet management port provides:

Local IP management connectivity RJ-45 connector mounted on the front of the ControlPanel Interface Card

10/100Base-TX link LED status indicator IP management over a dedicated DS0 bearer channel

- CLI management via the V.34 modem port on the Single-Channel POTS Service Card with V.34 Modem

Contains integrated TFTP client for remote download ofController software upgrades

SNMP agent for use with SNMP-based Element ManagementSystems

CLI offers 3 levels of password-controlled security

Network DS3 Interface: Line rate: 44.736 Mbps 20 ppm Line code: bipolar with three-zero substitution (B3ZS) Framing format: M23 and C Bit parity Transmit impedance: 75 5%, unbalanced Transmit jitter attenuation: meets ANSI T1.102 requirements Transmit amplitude: meets ANSI T1.102 pulse mask with

0.36 to 0.85 Vp requirements Transmit length (cable): 500 ft (152.4 m) to cross-connect Receive sensitivity: -10 dB w/r DSX-3 120 mVp to 900 mVp

input range with automatic gain control circuit Input range with automatic gain control 0 to 450 ft with no

need to use LBO commands DS3 connectors: 4 SMB jacks (SMB-to-BNC adapter cables

available) 3 dB jumpers can be inserted on the Trunk Interface to

attenuate the DS3 TX signal

8/2/2019 Axxius800 Dual Port Ds3 Controller Rel2 0 Spec Sheet

3/3

T e c h n i c a l S p e c i f i c a t i o n s f o r t h e A x x i u s 8 0 0 D u a l - P o r t D S 3 C o n t r o l l e r C a r d

The Carrier Access logo is a registered trademark and Axxius and solve for x are trademarks of Carrier Access Corporation.

All other trademarks are the property of their respective companies. All specifications subject to change without notice.

Copyright 2003 Carrier Access Corporation. All rights reserved. 027-0136-1300revision: June 2003

Product Ordering Infor

Inside Sales Represe

inside-sales@carrieracce

800-365

303-218

5395 Pearl P

Boulder, Colorado

www.carrieracce

Service Cards Supported: Hardened Dual V.35/.54 Service Card Hardened Low-Speed Interface Protection Card Hardened Order Wire Single-Channel POTS Service Card Hardened Order Wire Single-Channel POTS Service Card with

V.34 Modem (modem not hardened)

Hardened Quad DS1 ADPCM Service Card Hardened Quad-Port Terminal Server Router (TSR) ServiceCard

Hardened Quad DS1 Service Card 8-Channel FXO Voice Service Card Dual, Quad, and Octal ISDN BRI Service Cards Single and Quad-Port OCU-DP Service Cards

Network Standards: ANSI T1.403 and T1.404 ITU G.703, G.704

Clocking: Loop-timed from any DS1 within the DS3 External from BITS clock input (T1.101, T1.102 Signal

Type) Revertive or non-revertive (provisionable) clock switching

provides automatic backup to secondary DS3 should theprimary DS3 fail

Operates as a Stratum 4E device as defined by TelcordiaTM

GR-1244-CORE and AT&T TR 62411

Alarms: 3 visible alarm outputs (critical/major/minor) 3 audible alarm outputs (critical/major/minor) 10 alarm inputs (user definable) All alarms are logged in an event log Loss of power triggers minor alarm Generates SNMP traps for alarming

Testing and Diagnostics: Supports maintenance signals specified in ANSI T1.404

(Section 7.1) Standard DS3 line and payload loopbacks RFC 2496 performance history

Power: 10 W maximum

Regulatory Approvals: USA

- UL 60950- FCC Part 15, Class A- Designed to NEBS Level-3 for type 2 and 4 equipment (not

certified) Canada

- CSA C22.2 No. 60950-00- ICES-003, Class A

Physical: Dimensions:

- 3.5 in (H) x 0.75 in (W) x 11.25 in (D)- 8.9 cm (H) x 1.9 cm (W) x 28.6 cm (D)

Weight: 10.2 oz (0.29 kg)

Environment: Operating temperature: -40 F to 149 F (-40 C to65 C)

Storage temperature range: -40 F to 158 F (-40 C to70 C)

Cooling method is by free air convection Maximum operating altitude: 10,000 ft (3,048 m) Minimum operating altitude: 197 ft (60 m) below sea

level Maximum non-operating altitude: 40,000 ft (12,192 m) Relative humidity (non-condensing) range: 0% to 95%