AXIOM Iconos R200, Replacement of the Lift-Tilting Base CSTD AXD3-340.805.04 AXD3-340.841.03 (1)

8/18/2019 AXIOM Iconos R200, Replacement of the Lift-Tilting Base CSTD AXD3-340.805.04 AXD3-340.841.03 (1)

1/32

© Siemens, 2010All documents may only be used for renderingservices on Siemens Healthcare Products. Anydocument in electronic form may be printedonce. Copy and distribution of electronic docu-ments and hardcopies is prohibited. Offenderswill be liable for damages. All other rights are re-

served.

Print No.:

SiemensVassholz

AXIOM Iconos R200

AXIOM Iconos R200

Replacements of Parts

AX

2010

AXD3-340.841.03.02.02

Replaces: AXD3-340.841.03.01.02

EnglishDoc. Gen. Date: 04.10

n.a.CS PSAXR-F

Replacement of the Lift-Tilting Base

© Siemens,2010

Also applicable for:

- AXIOM Luminos dRF070305000703051807030930071524600590261910094158


2/32

2 Copyright / Version / Disclaimer

AXIOM Iconos R200 AXD3-340.841.03.02.02 © Siemens, 201004.10 CS PS AX R-F

Page 2 of 32

1Copyright/ Version/ Disclaimer

Copyright

“© Siemens, 2010“ refers to the copyright of a Siemens entity such as Siemens Aktienge-sellschaft - Germany, Siemens Shenzhen Magnetic Resonance Ltd. - China, SiemensShanghai Medical Equipment Ltd. - China, Siemens Medical Solutions USA Inc. - USA,

Siemens Healthcare Diagnostics Inc. - USA and/or Siemens Healthcare Diagnostics Prod-ucts GmbH - Germany.

Document Version

Siemens reserves the right to change its products and services at any time.

In addition, manuals are subject to change without notice. The hardcopy documents corre-spond to the version at the time of system delivery and/or printout. Versions to hardcopydocumentation are not automatically distributed. Please contact your local Siemens officeto order current version or refer to our website http://www.healthcare.siemens.com.

Disclaimer

Siemens provides this documentation “as is“ without the assumption of any liability underany theory of law.

The installation and service of equipment described herein requires superior understand-ing of our equipment and may only be performed by qualified personnel who are speciallytrained for such installation and/or service.


3/32

© Siemens, 2010 AXD3-340.841.03.02.02 AXIOM Iconos R20004.10 CS PS AX R-F

Table of Contents 3

Page 3 of 32

0TableofContents

1 _______ Removing the Luminos dRF Unit Support ___________________________ 4

Preparatory Measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Cover Panels on the Lifting Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Cover Panels on the Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Cover Panels on the Unit Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Unit Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Installing the Transport Carriage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2 _______ Removing the Iconos R200 Unit Support ___________________________ 15

Cover Panels on the Lifting Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Cover Panels on the Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Cover Panels on the Unit Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Unit Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Installing the Transport Carriage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

3 _______ Removing the Lifting Base _______________________________________ 25

Removing the Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Removing the Lifting Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

4 _______ Installation and Adjustment ______________________________________ 27

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Adjusting the Safety Limit Switches: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Adjusting the Potentiometers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Adjustments with the Luminos dRF with Bucky Wall Stand . . . . . . . . . . . . . . . . . . . 28Installing the Cover Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

5 _______ ______________________________________________________________ 30

6 _______ List of Hazard IDs ______________________________________________ 31


4/32

4 Removing the Luminos dRF Unit Support


Page 4 of 32

1-1Removingthe Luminos dRFUnitSupport

Preparatory Measures 0

If the Luminos dRF system has a Bucky wall stand, the position of the lifting base must bemarked as exactly as possible on the floor.

The new lifting base must then be installed again in exactly (millimeter accuracy) the sameposition so that center of the tube detector center exactly match.

It is absolutely necessary to work very accurately here, because correction of a differencetakes a lot of time.


5/32


Removing the Luminos dRF Unit Support 5

Page 5 of 32

Cover Panels on the Lifting Base 1.1

1. Remove the top cover panel.

2. Remove the side cover panels.

Fig. 1: Lifting base cover panel Pos. 1 Front cover panel screws

Pos. 2 Cable cover panel

Pos. 3 Free holes


6/32



Page 6 of 32

Cover Panels on the Extender 1.2

• Remove the two cover panels on the extender (1 /Fig. 2 / p. 6).

• Remove the side cover panel on the extender (1 /Fig. 3 / p. 6).

• Remove the cover panel on the extender mount (2 /Fig. 3 / p. 6).

Fig. 2: Cover panels on the extender, 1

Fig. 3: Cover panels on the extender, 2


7/32



Page 7 of 32

Cover Panels on the Unit Support 1.3

1. Remove the footrest and the other parts on the patient table.

2. Remove the side cover panels on the unit support (1-3 /Fig. 4 / p. 7).

3. Remove the fan cover panel at the head end on the unit support (1 /Fig. 5 / p. 7).

Fig. 4: Cover panels at foot end Fig. 5: Cover panels at head end


8/32



Page 8 of 32

Unit Position 1.4

Move the unit into the following position:

• Position the spotfilm device and column so they are centered.

• Move the unit into the 0° position.• Position the tabletop so it is flush with the frame.

• Move the lifting base with the SSW or mechanically.

Set a distance of 455 mm from the bottom edge of the extender to the top edge ofthe floor plate.

Fig. 6: Distance between the floor plate - extender


9/32



Page 9 of 32

Cabling 1.5

NOTE The illustrations in this section are for orientation only andcan differ from the actual status of the system.

• Remove the cable clamp and flexible plastic chain on the extender.

Fig. 7: Cable deflector

• Remove the cable ties from the wiring harness on the side of the extender (Fig. 8 / p. 9).

Fig. 8: Laying the cables in the extender

1


10/32



Page 10 of 32

• Unplug the connections between the lifting base and the M1 assembly (line powerassembly).

Fig. 9:

• Remove the contact protector from the F1 trip breaker (1/ Fig. 10 / p. 10).

Fig. 10: Power supply assembly shielding

• Remove the 2 mounting nuts for the line power assembly.

1


11/32



Page 11 of 32

• Label the motor cable to the Micromasters (1/ Fig. 11 / p. 11) and disconnect it.

Fig. 11:

• Remove the transformer (2/ Fig. 11 / p. 11). It will be used again.

• Pull all cables to the right side of the base in the direction of the transformer out of thebase. Be careful of the connectors (Fig. 9 / p. 10).

• Remove the support plate (3/ Fig. 11 / p. 11) with the Micromasters. Take note of thecabling! The support plate with the Micromasters will be used again.


12/32



Page 12 of 32

Installing the Transport Carriage 1.6

1. Install the plates at the head and foot ends of the unit support and tighten all screws.

Fig. 12: Panel 1 at head end

Fig. 13: Panel 2 at head end

Fig. 14: Panel 1 at foot end

Fig. 15: Panel 2 at foot end


13/32



Page 13 of 32

2. Install the transport carriages at the head and foot ends (thread the screws in onlyloosely) and make sure that the safety screws to prevent tilting of the unit support areinserted:

3. Install the transverse struts (thread in the screws only loosely). Prior to installation, thetransverse struts must be connected together (tighten the screws).

4. First tighten all screws on the transport carriage and then the screws for the transversestruts.

5. Install the transport castors at the head and foot ends.

6. Turn down the transport castors with the spindles so that the transport castors areunder light pressure.

7. Remove the screws between the unit support and the extender.

8. Evenly turn down the transport castors with the spindles so that the unit support andextender come apart.

Fig. 16: Transport carriage

Fig. 17: Transport carriage, detail


14/32



Page 14 of 32

9. Move the unit support so that the base is accessible from the front and side. Pay care-ful attention to the cables and take them out of the extender!

Fig. 18: Unit supporet / extender

10. Carefully pivot the unit support at the foot end until the extender is accessible with thelift truck and pallet. Be extremely careful of the cables!

11. Completely remove the M1 assembly (line power assembly) from the lifting base andplace it carefully to the side.


15/32


Removing the Iconos R200 Unit Support 15

Page 15 of 32

2- 2Removing theIconos R200 UnitSupport

Cover Panels on the Lifting Base 0

1. Remove the top cover panel.

2. Remove the side cover panels (if installed).

Fig. 19: Lifting base cover panel Pos. 1 Front cover panel screws

Pos. 2 Cable cover panel

Pos. 3 Free holes


16/32

16 Removing the Iconos R200 Unit Support


Page 16 of 32

Cover Panels on the Extender 2.1

Remove the cover panels on the extender in the following sequence:

1. Top extender cover panels (2 pieces) (1/ Fig. 20 / p. 16)

2. Left side cover panel (2/ Fig. 20 / p. 16)3. Bottom (3/ Fig. 20 / p. 16)

4. Right side cover panel (4/ Fig. 20 / p. 16)

5. Top cover (5/ Fig. 20 / p. 16)

Fig. 20: Cover panels on the extender

1 2

34

5


17/32



Page 17 of 32

Cover Panels on the Unit Support 2.2

• Remove the side cover panel (1/ Fig. 21 / p. 17).

• Remove the two cover panel sections on the foot end of the unit support(1/ Fig. 22 / p. 17). Remove the bottom cover panel first.

Fig. 21: Unit support cover panels, left Fig. 22: Unit support cover panels, right

1

2

3

1

2


18/32



Page 18 of 32

Unit Position 2.3

Move the units into the following positions:

• Position the spotfilm device and column so they are centered.

• Move the unit into the 0° position.• Position the tabletop so it is flush with the frame.

• Move the lifting base with the SSW or mechanically.

Set a distance of approx. 80 cm from the top edge of the extender to the top edgeof the floor plate (Fig. 23 / p. 18).

Fig. 23:


19/32



Page 19 of 32

Cabling 2.4

• Remove the cable deflector on the extender (1/ Fig. 24 / p. 19).

• Remove the cable ties from the wiring harness on the side of the extender(Fig. 25 / p. 19).

Fig. 25: Laying the cables in the extender

Fig. 24:

1

2

1


20/32



Page 20 of 32

• Unplug the connections between the lifting base and the M1 assembly (line powerassembly).

Fig. 26:

• Remove the contact protector from the F1 trip breaker (1/ Fig. 27 / p. 20).

Fig. 27: Power supply assembly shielding

• Remove the 2 mounting nuts for the line power assembly.

1


21/32



Page 21 of 32

• Label the motor cable to the Micromasters (1/ Fig. 28 / p. 21) and disconnect it.

Fig. 28:

• Remove the transformer (2/ Fig. 28 / p. 21). It will be used again.

• Pull all cables to the right side of the base in the direction of the transformer out of thebase. Be careful of the connectors (Fig. 26 / p. 20).

• Remove the support plate (3/ Fig. 28 / p. 21) with the Micromasters. Take note of thecabling! The support plate and the Micromaster will be used again.


22/32



Page 22 of 32

Installing the Transport Carriage 2.5

1. Install the plates at the head and foot ends of the unit support and tighten all screws.

2. Install the transport carriages at the head and foot ends (thread the screws in onlyloosely) and make sure that the safety screws to prevent tilting of the unit support areinserted:

3. Install the transverse strut ((1/ Fig. 33 / p. 23) and (1/ Fig. 34 / p. 23)) and angled struts ((2/ Fig. 33 / p. 23) and (2/ Fig. 34 / p. 23)) (thread in the screws only loosely). Prior toinstallation, the transverse struts must be connected together (tighten the screws).

NOTE If two transverse struts are installed in place of angled struts,the two transverse struts must be installed.

Fig. 29: Panel, foot end Fig. 30: Panel, head end

Fig. 31: Transport carriage 1 Fig. 32: Transport carriage 2


23/32



Page 23 of 32

4. First tighten all screws on the transport carriage and then the screws for the transversestrut/struts and angled struts (if installed).

5. Install the transport castors at the head and foot ends.

6. Turn down the transport castors with the spindles so that the transport castors areunder light pressure.

7. Remove the screws between the unit support and the extender.

8. Evenly turn down the transport castors with the spindles so that the unit support andextender come apart.

9. Move the unit support so that the base is accessible from the front and side. Pay care-ful attention to the cables and take them out of the extender!

Fig. 35: Unit supporet / extender

10. Carefully pivot the unit support at the foot end until the extender is accessible with thelift truck and pallet. Be extremely careful of the cables!

Fig. 33: Transverse and angled strut, head

end

Fig. 34: Transverse and angled strut, foot end


24/32



Page 24 of 32

11. Completely remove the M1 assembly (line power assembly) from the lifting base andplace it carefully to the side.


25/32


Removing the Lifting Base 25

Page 25 of 32

3- 3Removing theLifting Base

Removing the Extender 0

• Install the transport carriage on the transport pallet (2/ Fig. 36 / p. 25).

• Install the transport castors (1/ Fig. 36 / p. 25) and (1/ Fig. 37 / p. 25).

• Position the transport pallet under the extender.

• Raise the transport castors with the spindles (Fig. 37 / p. 25).

• Remove all Allen mounting screws from the extender (2/ Fig. 37 / p. 25).

• Pull down the extender from the rotation axis onto the transport pallet.

• Move the extender away with the transport pallet and place it down on the floor.

• Remove the transport carriage and transport castors.

Fig. 36: Fig. 37:


26/32

26 Removing the Lifting Base


Page 26 of 32

Removing the Lifting Base 3.1

• Install the transport safety device (1/ Fig. 38 / p. 26) from the new lifting base in the oldlifting base.

Fig. 38: Lifting base transport safety device • Remove all floor mounting screws from the lifting base.

• Install the transport carriage on the lifting base (1/ Fig. 39 / p. 26).

Fig. 39:

• Install the transport castors.

• Raise the lifting base and move it away.


27/32


Installation and Adjustment 27

Page 27 of 32

4- 4InstallationandAdjustment

Installation 0

NOTE Shipped status of the lifting base:

The new lifting base is shipped with floor mounting materials

and a complete set of cover panels.

The electronic assemblies should be taken from the old lift-ing base (transformer, Micromaster assembly and line powerassembly).

The safety limit switches are pre-set (for a unit with 40 cm I.I.)(Iconos R200).

NOTE With a Luminos dRF system with Bucky wall stand, the newlifting base must be positioned exactly (millimeter accuracy)

in the same position as the old lifting base! This is prerequi-site for centering the Bucky wall stand.

• Installation of the lifting base must be performed per the Installation Instructions.

• When doing this, the following points absolutely must be observed:

- Leveling

- Inserting shims

- Torque values for the mounting bolts.

Installation of the electronic assemblies in the lifting base is performed in the reversesequence.

NOTE Shielding of the motor cables absolutely must be the same asin the "old" lifting base.

It is possible that insulation must be removed at the particu-lar location.

Installation of the lifting base and the unit support must be performed per the InstallationInstructions.


28/32

28 Installation and Adjustment


Page 28 of 32

Adjustment 4.1

Adjusting the Safety Limit Switches: 0

• Luminos dRF: Perform adjustment of the safety limit switches per the chapter LiftingBase > Replacing the Safety Limit Switches in the instructions Replacement ofParts, Luminos dRF, Basic Unit with Tube Unit and Collimator, Print NumberAXD3-500.841.01 (for the latest version, see the CB-DOC).

• Iconos R200: Perform adjustment of the safety limit switches per the chapter LiftingBase > Adjustment of the Safety Limit Switches in the instructions Replacement ofParts, Iconos R200, Basic Unit and Collimator, Print Number AXD3-340.841.01 (forthe latest version, see the CB-DOC).

Adjusting the Potentiometers 0

Adjust the potentiometers accordingly in the SSW.

- Adjustment/ Calibration/ Tilt Drive/ Tilt Drive: Potentiometer Adjustment

- Adjustment/ Calibration/ Tilt Drive/ Tilt Drive: Potentiometer Adjustment

- Adjustment/ Calibration/ Tilt Drive/ Tilt Drive: Limitation of + 90° Position

or

- Adjustment/ Calibration/ Tilt Drive/ Tilt Drive: Limitation of + 45° Position

- Adjustment/ Calibration/ Tilt Drive/ Tilt Drive: Limitation of - 90° Position

or

- Adjustment/ Calibration/ Tilt Drive/ Tilt Drive: Limitation of - 45° Position

- Adjustment/ Calibration/ Tabletop, longitudinal/ Patient mounting height: Loweredfootrest in + 90 ° or - 90° position

Adjustments with the Luminos dRF with Bucky Wall Stand 0

• Place a ball phantom on the centering cross of the Bucky wall stand and trigger anexposure with the tube unit of the Luminos dRF unit. If the ball in the exposure is out-side of the center, a correction is necessary. This can be done only by moving theBucky wall stand or lifting base of the Luminos dRF (unit support and extender must beremoved again).

• Corrections and ball phantom exposures must be repeated until the ball in the expo-sure is exactly in the center of the phantom.


29/32


Installation and Adjustment 29

Page 29 of 32

Installing the Cover Panels 0

• Install all cover panels in the reverse sequence.

- Install all new lifting base cover panels included in the shipment.


30/32

30


Page 30 of 32

5-5

No changes. Initial publication.


31/32


List of Hazard IDs 31

Page 31 of 32

6- 6Listof Hazard IDs

There are no Hazard IDs in this document.


32/32

32 List of Hazard IDs

AXIOM Iconos R200, Replacement of the Lift-Tilting Base CSTD AXD3-340.805.04 AXD3-340.841.03 (1)

Documents

Transcript of AXIOM Iconos R200, Replacement of the Lift-Tilting Base CSTD AXD3-340.805.04 AXD3-340.841.03 (1)