Avaya.Certkey.6002-1.v2014-06-16.by.GRETCHEN - · PDF...

Avaya.Certkey.6002-1.v2014-06-16.by.GRETCHEN.70q

Number: 6002-1Passing Score: 660Time Limit: 120 minFile Version: 24.5

http://www.gratisexam.com/

Exam Code: 6002-1

Exam Name: Avaya Aura(TM) Communication Manager and CM Messaging (R6.0)Implementation Exam

Exam A

QUESTION 1When troubleshooting a system fault. If the web interface or SAT are unavailable. Which method should beused?

A. SAIB. TTY2C. CLID. Modem

Correct Answer: CSection: (none)Explanation

Explanation/Reference:CLI - Command Line Interface, Using Putty to access.

QUESTION 2Which two servers support RAID 5 configuration for CM 6.0?(Choose two.)

A. S8730 Server with 8 GB RAMB. S8800 Server with 12 GB RAMC. S8510 Server with 8 GB RAMD. S8300 Server with 8 GB RAM

Correct Answer: BCSection: (none)Explanation

Explanation/Reference:Avaya S8510 Server:

Memory: 4 GB to 8 GB Disks: Remove two 146-GB disks; replace with three 146-GB disks; configure RAID 5 SAMP card: replace with PCI blank

Avaya S8800 Server: Memory: 4 GB to 12 GB Disks: Remove two 146-GB disks; replace with three 146-GB disks; configure RAID 5

QUESTION 3Hunt group number 99, with group extension 4199, is administered for messaging. Which command needsto be executed at the SAT terminal to troubleshoot hunt group 99?


A. show tracelog huntgroup 419B. view logs realtime huntgroup 99C. display realtime logs huntgroup 99D. list trace hunt-group 4199

Correct Answer: DSection: (none)Explanation

Explanation/Reference:

QUESTION 4A customer needs to set up SIP integration on Communication Manager Messaging Application 8.0 Whatare three pieces of information that are needed to meet this requirement?(Choose three)

A. Signaling Group numberB. SIP domainC. Transport MethodD. Extension LengthE. Hunt Group number

Correct Answer: BCDSection: (none)Explanation

Explanation/Reference:Create a signaling group for messaging before you add a trunk group.Enter the command: add signaling-group 98.

Verify that the following fields are set as indicated below. Some of these fields are pre-populated: Group Number : Should be 98. Group Type : SIP (Note: As soon as you enter the Group Type , more fields display on this form.) Transport Method: tls Near-end Node Name: procr Far-end Node Name: cmmessaging Near-end Listen Port: 5061 Far-end Listen Port: 6061 (must have a different port number because it shares the same IP address asNear-end Listen Port) Far-end Network Region: 1 Far-end Domain: avaya.com DTMF over IP: rtp-payloadEnable Layer 3 Test?: yDirect IP-IP Audio Connections: y IP Audio Hairpinning? N

QUESTION 5Which three are best that can be performed to verify a Communication Manager Messaging 6.0 applicationis working property? (Choose three)

A. Verify the Hunt Group statusB. Check the Messaging port status using the display port commandC. Call the Messaging Hunt GroupD. Check the Messaging port status using the status port commandE. Check the Messaging

Correct Answer: ACESection: (none)Explanation


QUESTION 6On a media gateway G450 which slots are permitted for the MM342?

A. V1 and V2B. V2 and V6C. V3 and V8D. V5 and V7


Explanation/Reference:Media Module - Media ModuleMM340 - V3, V4, V8MM342 - V3, V4, V8MM710 - Any Media Slot, V1 - V8MM711 - Any Media Slot, V1 - V8Mm712 - Any Media Slot, V1 - V8MM714 - Any Media Slot, V1 - V8MM716 - Any Media Slot, V1 - V8MM717 - Any Media Slot, V1 - V8MM720 - Any Media Slot, V1 - V8MM722 - Any Media Slot, V1 - V8S8300D - V1

QUESTION 7A customer is planning to upgrade from CM 5.X to CM 6.0 on an existing S8510 server. What is the totalminimum memory requirement for this upgrade?

A. 4 GB RAMB. 8 GB RAMC. 12 GB RAMD. 16 GB RAM

Correct Answer: BSection: (none)Explanation

Explanation/Reference:Avaya S8510 Server:

Memory: 4 GB to 8 GB Disks: Remove two 146-GB disks; replace with three 146-GB disks; configure RAID 5 SAMP card: replace with PCI blank

Avaya S8800 Server:

Memory: 4 GB to 12 GB Disks: Remove two 146-GB disks; replace with three 146-GB disks; configure RAID 5

QUESTION 8Which screen is used while upgrading the system platform from Release 6.0.0.09 to Release 6.0.0.11?

A. Communication Manager Web interfaceB. Console domain ->Server Management->Patch ManagementC. Console domain->Server Management->Platform UpgradeD. Console domain->Virtual Machine Management


Explanation/Reference:Downloading patches

Procedure1. Click Server Management > Patch Management .2. Click Download/Upload .3. On the Search Local and Remote Patch page, select from the following locationsto search for a patch.

Avaya Downloads (PLDS)HTTPSP ServerSP CD/DVDSP USB DiskLocal File System

4. If you selected HTTP, enter the patch URL.Click Configure Proxy to specify a proxy server if required.5. If you selected SP Server , copy the patch into System Platform server directory /vsp-template :6. If you selected Local File System , click Add to locate the service pack file on your computer and thenupload.7. Click Search to search for the required patch.8. Choose the patch and click Select .

QUESTION 9Which three statements about CM_Duplex template CM 6.0 ARE TRUE? (Choose three.)

A. Software duplication is available. But hardware duplication is not availableB. The S8510 Server is not used for duplicationC. Server duplication is configured via "Failover" option on CDOM's web interfaceD. S8730 with DAL 2 card does not support server duplication in CM 6.0E. The CM duplex template supports CMM

Correct Answer: ABDSection: (none)Explanation


The Communication Manager Main Core Duplex template is installed on two identical supported serversand directly interconnected with the Duplication Link. The left-most red column has the details about theMain Core Duplex template.

QUESTION 10Which Gateway command resets the Gateway back to factory default?

A. resetB. restartC. softbootD. nvram init


Explanation/Reference:Gateway Configuration Script starts automatically after running the nvram init command.

QUESTION 11A technician wants to test and see if the voice channel between two IP phones is shuffled. Which commandin Site Administration Terminal (SAT) can be used to determine the type of IP connection, and to check if

the voice channel is shuffled?

A. status station <extension>B. status shuffling <extension>C. list station <extension>D. test station <extension

Correct Answer: ASection: (none)Explanation

Explanation/Reference:Use status station to view the setup of each individual station.This command is often the first place to gather information when a user reports a problem with a phone.For example, if a user tells you that the phone rings a short ring and the call goes directly to coverage, use status station to see if send all calls (SAC) is activated on the user’s extension.

To view the status of extension 7236:1. Type status station 7236 and press ENTER. The GENERAL STATUS form appears. In our example, you can see that this 6408D+ phone is workingproperly (inservice/on-hook), but send all calls (SAC) is active. This would explain why they cannot answer their calls before they go to coverage.

QUESTION 12Which Ethernet port on S8800 server is used for server duplication?

A. ETH0B. ETH1C. ETH2D. ETH3



Connection schema for cable duplicated serversThe following graphic show the connection schema for a S8800 cable duplicated server pair.

1 - Null modem cable connecting the servers through the RS-232 serial port.2 - Ethernet cable connecting to the services port (Eth1).3 - Ethernet cable connecting the servers to the customer network through the customer network port(Eth0).4 - Ethernet cable connecting the servers through the d ual NIC port (Eth3).5 - The cable connects the IMM port of one server to NIC port 3 (Eth2) of the other.

1 - Straight-through Ethernet cable connecting the servers to the customer network through the customernetwork port (Eth0)

QUESTION 13Which three components are part of Avaya Aura CM_survRemote_Embed template? (Choose three)

A. Utility ServicesB. CM 6.0C. Session Manager 6.0D. CMM 6.0E. AES 6.0

Correct Answer: ABDSection: (none)

Explanation


QUESTION 14A technician is planning to upgrade an Avaya Communication Manager system to Release 6 .0 fromRelease 5.2. Which two tasks must be performed during the upgrade procedure?(Choose two)

A. The S8700-series servers must be replaced by S8800 serversB. All G350 gateways must be replaced by G430 or G450 gatewaysC. The Survivable Remote servers must be upgraded to release 6.0D. The Survivable Remote servers can stay at release 5.2

Correct Answer: ACSection: (none)Explanation


The supported servers for Communication Manager Release 6.2 are: Avaya S8300D Server Avaya S8510 Server (upgrade required) Avaya S8800 Server (upgrade required) HP ProLiant DL360 G7 Server* Dell™ PowerEdge™ R610 1U Server*

Both the Avaya S8510 and S8800 Servers require hardware upgrades; the details are on a later slide Theasterisk by the HP and Dell servers indicates both are Avaya common servers that are configuredspecifically for certain supported Avaya products.

QUESTION 15In the navigation pane, What are the steps to create a test mailbox on the Communication ManagerMessaging 8.0 Application?

A. Select Messaging Administration then Subscriber Management, and then Click Add or EditB. Select Subscriber Administration, then Click netC. Select Subscriber Administration, then Subscriber Management and then Chen Click AddD. D. Select Forms Control, and then at the command line run the Add Subscriber command


Explanation/Reference:You added two stations (4004 and 4005 ) during the configuration process. Now add subscribermailboxes to the stations. In the Navigation pane, select Messaging Administration à Subscriber Management.

In the Local Subscriber Mailbox field, type the extension number of the first test subscriber. In this exercise,this number should be 4004, the first station that you added.

Click Add or Edit . The Add Local Subscriber window launches.

QUESTION 16When configuring a G450 Media gateway, which two port settings must be set? (Choose two)

A. FTP ServerB. 100 MB port speedC. auto-negotiation enabledD. Full Duplex

Correct Answer: BDSection: (none)Explanation


QUESTION 17A switch administrator wants to busyout trunk 53 for maintenance and administration work However, thereis one call active on port 5 of the trunk. Which command should be executed from the SAT terminal to find out IP addresses and ports of the near-end and far-end node of the audio connection?

A. status trunk 53/5B. list trace 53/5C. display trunk statistics 53/5D. status port 53/5


Explanation/Reference:Packet loss and jitter can cause a noisy connection that eventually breaks up, creating gaps in theconversation and making speech unintelligible. Use status station to check for station-side IP problems, including problems with an IP phone, and usestatus trunk to check for trunk-side IP problems.Each command generates snapshot jitter buffer size (ms) and packet loss report for a particular station ortrunk group member that shows:

the number of packets that are lost or corruptedamount of jitter on the connection

In this instance, jitter is the variability in the amount of time (in milliseconds) that packets are received overthe network. When jitter increases, the user experiences a noisy connection, delays, and a general loss of quality,making speech unintelligible.

NOTE:If you issue a status station or status trunk command for a non-IP station, or the connection is hairpinnedor shuffled, then the packet loss and jitter size information doesnot appear. See the Administration for Network Connectivity for Avaya M ultiVantage™ Software ,555-233-504, for more information.

Resource: Avaya Communication Manager Little Instruction Book for BasicDiagnostics (http://www.telesavers.com/User%20Guides/ACM/ACM%20 Basic%20Diagnostics%2011-03.pdf)

QUESTION 18Which three objects can be downloaded from the Product License Delivery System (PLDS)? (Choosethree.)

A. Authentication fileB. PatchesC. Firmware updatesD. PuTTyE. Communication Manager Templates

Correct Answer: BCESection: (none)Explanation

Explanation/Reference:Authentication file will be downloaded from RFA site. Unique authentication files are created by theAuthentication File System (AFS), an online applictaion at http://rfa.avaya.com

QUESTION 19Which two statements describe the new procedures that a customers can use to directly and permanentlyturn ON or OFF licensed features in CM 6.0?(Choose two)

A. Customers can turn features ON or OFF using the change system parameters customer-optionscommand on the System Access Terminal (SAT)

B. Customers can turn features ON or OFF using the System Management Interface Administration pageC. Customers can access PLDS directly to turn features ON or OFF and then download and install a new

license file with the updated features.D. Customers can turn features ON or OFF using the WebLM server on the System Platform Management

Console

Correct Answer: CDSection: (none)Explanation


QUESTION 20Which statement describes the action to assure the CM_SurvRemoteEmbed Template was installedcorrectly?

A. From a browser. Using the Communication Manager IP address, successfully log into theCommunication Manager System Management Interface (SMI)

B. From a browser logged into Communication Manager, select Administration->Server (Maintenance) ->Server-> Process Status, click on View and verify CommunicaMgr appears

C. From a browser logged into the System Management Console verify cm, bsm and utility_server appearand the Application Status is running

D. When monitoring the template installation workflow status, verify the message, "wizard completedsuccessfully" displays


Explanation/Reference:Select Virtual Machine Management � Manage to ensure that the new virtualmachines (CM, BSM and Utility Server ) are Running :

QUESTION 21Which three statements about when Communication Manager Release 6.0 is deployed as a Feature Serverare true? (Choose three)

A. It supports G450/G430 gatewaysB. It supports Analog trunksC. It supports SIP telephonesD. It supports SIP trunksE. It supports Digital trunks

Correct Answer: ACDSection: (none)Explanation


This diagram shows the five Communication Manager “building blocks” that combine to create acommunications enterprise, all under the Avaya Aura® inoperability umbrella. Let’s review these five CMservers:

The upper center (purple) box shows the simplex and duplex configurations for both FeatureServer and Evolution Server modes. The lower left (gray) box shows the SIP-only branch in which CM functions as the SurvivableSimplex server in the Feature Server mode. The lower right (green) box shows a non-SIP branch in which CM functions in the Evolution Servermode. The lower center (orange/yellow) box shows a mixed SIP + non-SIP or “hybrid” branch in which the SIPendpoints register with Session Manager in the main core cloud, and

H.323 endpoints register with CM, which functions in the Evolution Server mode.

QUESTION 22When using the Avaya site Administrator GEDI interface. Which command would be used to check theconfiguration of a telephone set with the extension of 1000?

A. print station 1000B. display station 1000C. shhow station 1000

D. view station 1000


Explanation/Reference:use display station to look at the station screens pageby-page

check the station screens for SAC, coverage pathslook at printed switch records for discrepanciescheck the alarms and errors logs

QUESTION 23Which three statements are true for a configuration that consists of duplicated S8800 main servers with aduplicated port network and a survivable core? (Choose three)

A. Software duplication exists between the two main S8800 serversB. The two main servers have duplicated IPSIsC. Hardware duplication exists between the two main S8800 serversD. The two main servers share a single control networkE. All CLAN and Medpro cards must be in one subnet

Correct Answer: ABESection: (none)Explanation


QUESTION 24A technician has installed a pair of duplicated S8800 servers with IPSI duplication. Which two proceduresindicate that the duplicated IPSIs are both operational? (Choose two)

A. The Enable Operation of IPSI Duplication field on the display system-parameter duplication form is setto y

B. IPSI circuit packs have been installed in slots1 and 2 of carrier A and one of the IPSI LEDs is flashingC. Execution of the test ipserver-interface command for both IPSI circuit packs shows PASS in the results

columnD. A ping test executed from the server to the IPSIs and from the IPSIs to the servers returns success for

the active IPSI and failure for the standby IPSI


Explanation/Reference:At the prompt, type: list ipserver-interface and press Enter to check IPSI status.

Verify that the duplicated IPSI administration is correct and that it is operational.(Note : Be Patient – you might have to execute this command a few times.)

At the prompt, type: list configuration all and press Enter. Verify that all circuit packs have been detected and appear in the report. Press F1[Cancel ] to exit this form:

QUESTION 25What are the recommended CLAN and MEDPRO port settings?

A. 10Mbps half duplexB. 1000Mbps full duplexC. 100Mbps full duplexD. 100Mbps half duplex


Explanation/Reference:Set the Auto (negotiation) field to n.

Set the Speed to 100Mbs and Duplex to Full. Press F3 [Enter ]:

QUESTION 26Which two statements are true regarding a media gateway fall back (recovery) to the main (primary)server? (Choose two)

A. All active (stable) IP calls on the media gateway drop when the media gateway falls back from thesurvivable server is registered to the main server

B. The list survivable-processor command can be used to confirm that the remote survivable server isregistered to the main server and that the remote survivable server is no longer active

C. When the main server recovers it issues registration requests to all to media gateways in the networkD. Executing the status media-gateways command from the main server will show which media gateways

are registered with the main server


Explanation/Reference:Type: list survivable-processor command on the active server to see the status of theSurvivable Remote Servers.

Verify that the Survivable Remote Embedded Server is registered to the main server andthat translations are updated :

The list media-gateway command.From the primary server , a command that shows all G700 Media Gateways currentlyadministered is: listmedia-gateway . Five fields are displayed: number, name, identifier, ip address andregistration status:• Number -- the assigned number to the G700 by the primary server administration• Name -- the name given to the G700 by the user• Identifier -- the way by which the primary server knows the G700 (i.e., serial number)• IP address -- the IP address of the G700.• 'Registered?' -- indicates whether a G700 is currently registered with the primary serveror not.

QUESTION 27To confirm that a survivable server is currently registered to the main CM server, using the SAT, whichcommand should be entered?

A. status ess clustersB. display survivable-processorsC. status ess port-networksD. status survivable-processors


Explanation/Reference:http://downloads.avaya.com/css/P8/documents/100092646

Use the following commands to verify the survivable core server translations:● list survivable-processor (executed on the main server) displays all translated survivable core servers.● status ess clusters displays:- Which clusters are enabled- When translations were last updated- What software release the main server and survivable core servers are runningThe survivable core servers can be on a later release than the main server but the main server shouldnever be on a later release than the survivable core servers. The software release should only be different when upgrades are being performed. Always upgrade thesurvivable core servers first and then the main server. ● The status ess port-networks command displays which Cluster ID is controlling each port network andwhich survivable core server the port networks (IPSIs) have on their priority lists.

To verify that the ESS is up and running and ready to take over the Port Networks (PNs)in the event the main server fails, type: status ess cluster:

To verify that both PN1 and PN2 are currently controlled by Server Cluster 1 – type: status ess port-networks:

QUESTION 28A customer wants to enable audio encryption for IP phone calls, but the option is not available on any ip-codec-set. Which procedure must be followed to obtain this feature?

A. From the SAT, type change system-parameters customer-options. Find the Media Encryption over IPfield, and set the option to Y. Save the change

B. From the SMI Feature Administration page, find the Media Encryption over IP field set the option to Y .Save the change

C. From the System Platform WetLM page, page, find the Media Encryption over IP field set the option toY. Save the change

D. From the Aura System Manager's Feature Server Administration page, find the Media Encryption overIP field, and set the option to Y. Save the change


Explanation/Reference:The Media Encryption field is set to “y”, and a Passphrase is entered. The configuredPassphrase must match on the Avaya S8300 Media Server and Avaya S8720 MediaServerrepresenting the near-end and far-end of this signaling group. The H.235 Annex HRequired field is set to “y” to enhance security of control signaling. The Far-endNetwork Regionparameter is set to 8, a network region that is different from the near-end devices on theAvaya S8300 Media Server. By assigning a unique network region to the far-end of thesignalinggroup, different codec and media encryption options may be used for calls that use theH.323 signaling group and trunk group.

QUESTION 29Which statement describes the action to assure the system platform was installed correctly?

A. From a laptop connected to the network, ping the dom0 IP address and verify a successful responseB. Immediately after the installation, verify the DVD is ejected from the drive and that the server rebootsC. After connecting to the server using PuTTY and logging in as root, verify there are no errors when

running the xm list commandD. From the System Management Console browser, verify Domain-0 and cdom are running


Explanation/Reference:xm listName ID Mem VCPUs State Time(s)Domain-0 0 512 4 r----- 88.0udom 1024 1 276.3

QUESTION 30Which statement is true about duplex servers in CM 6.0?

A. The Survivable Remote Duplex template includes Branch Session ManagerB. CM uses the high availability feature that System Platform can now provideC. The license file for a survivable server is different than the license file of the main serverD. The main and all survivable server require an authentication file




QUESTION 31System Platform webconsole is used to apply the service pack for which three virtual machines? (Choosethree)

A. System PlatformB. AES 6.0C. Utility ServerD. Communication Manager 6.0E. CMM 6.0


Explanation/Reference:Select Server Management > Patch Management > Manage to verify the patch installation.

Notes Select Server Management > Patch Management > Manage to verify the patch installation.You can click on the Patch ID to see details about the patch. Again, the Service Effecting field indicatesthat this patch can be service affecting.

QUESTION 32Which procedure must be followed while migrating from CM 5.2.1 (S8800 Server with 2 HDD) to CM 6.0?

A. Insert 3rd hard drive, run Raid CD, and then take backupB. Take backup, store the backup locally, insert 3rd hard drive, and then run Raid CD after rebootingC. Insert the Raid CD, reboot the server, and then take backupD. Insert the hard drive and the 3rd hard drive is incorporated automatically



QUESTION 33Which Communication Manager 6.0 command is used to add a new survivable core server so that it wouldregister with the Main server?

A. add survivable-processorB. add survivable-processor coreC. add survivable-processor coreD. add survivable-processor <node-name>


Explanation/Reference:Add the Survivable Remote Server as a survivable process using the add survivable-processor

<Survivable Remote ServerName> , where Survivable Remote Server Name is the name of theSurvivable Remote Server that you just added to the Node Names table (previous slide).

QUESTION 34Which Ethernet port on S8800 server is connected to the customer network?

A. ETH0B. ETH1C. ETH2D. ETH3


Explanation/Reference:Connection schema for cable duplicated serversThe following graphic show the connection schema for a S8800 cable duplicated server pair.

1 - Null modem cable connecting the servers through the RS-232 serial port.2 - Ethernet cable connecting to the services port (Eth1).3 - Ethernet cable connecting the servers to the cu stomer network through the customer networkport (Eth0).4 - Ethernet cable connecting the servers through the dual NIC port (Eth3).5 - The cable connects the IMM port of one server to NIC port 3 (Eth2) of the other.

QUESTION 35When using the Avaya Site Administrator GEDI interface, which command would be used to build a newtelephone set with the extension of 1000?

A. new station 1000B. add station 1000C. build station 1000D. add set 1000


Explanation/Reference:Type add station 1001 and press Enter . Complete the fields as indicated then press Enter .

QUESTION 36Which two components are part of the Avaya Aura CM_Simplex template? (Choose two)

A. Utility ServicesB. CM 6.0C. Session Manager 6.0D. Avaya Enablement Services (AES)

Correct Answer: AB

Section: (none)Explanation


QUESTION 37When using the Avaya Site Administrator GEDI interface, which command would be used to confirm thatMedia Gateway number 3 is registered?

A. show media-gateway 3B. display media-gateway 3C. print media-gateway 3D. view media-gateway 3


Explanation/Reference:Taken From the Avaya Site Administration Reference Guide

Command abbreviations

It is not necessary to type the entire command. You need to type only as manycharacters as are required to make the command unique. For example, you can typedisp instead of display .

If you use too short of an abbreviation, (like dis ), the system responds with the errormessage "dis is an ambiguous entry" and displays as suggestion like "Please choosefrom one of the following 'disable' or 'display.'" Once the correct abbreviated command isentered, the screen displays the entire command in the upper left corner and the pagenumber in the upper right corner.

QUESTION 38For Avaya Aura CM6.0 how is the License file installed on the server?

A. by accessing the Web interface of CMB. using the loadlicense command through shell prompt of CMC. through the Web interface of MOM0D. using the Web Interface of Console Domain


Explanation/Reference:To install the license file:

Go to the System Platform console (cdom) for Communication Manager Select Server Management > License Management • Click License Administration . • Log in to the Web License Manager: Click Install License

QUESTION 39Concerning the type of Integration with Communication Manager, on the Navigation Pane, where is theCommunication Manager Messaging 6.0 Application mentioned or configured?

A. Click the System wide Messaging Parameters, then Switch Integration Type fieldB. Click Switch Link Administration, then Switch TypeC. Click Integration TypeD. Click Switch Link Administration, then Switch Link Admin, and then Switch Integration Type field


Explanation/Reference:You must perform the Switch Link Administration before you start Messaging

In the Navigation pane, under the Switch Link Administration section, click Switch Link Admin.

The Switch Link Admin page displays

QUESTION 40A small enterprise customer needs 445 SIP/H.323 users. Which CM6.0 template will be the mosteconomical solution?

A. CM_SimplexB. CM_survRemote_EmbedC. CM_DuplexD. CM_onlyEmbed



QUESTION 41For duplex S8800 servers running CM6.0 by default which Ethernet port communicates with IPSIs?

A. Eth0B. Eth1C. Eth2D. Eth3



QUESTION 42When configuring a G450 Media gateway using the gateway CLI interface, which command would be usedto view the serial number and software status?

A. show serial numberB. show systemC. print G450D. show G450


Explanation/Reference:At the gateway command line interface type the show system command to review the gatewayadministration. Write down the serial number of the gateway—it is required for

Communication Manager administration. Even better, you can click and drag your mouse over the serialnumber then copy it to the clipboard. Then it is ready to paste into the Communication Manager form coming up soon.

QUESTION 43Which three elements are needed to add a CLAN IP interface? (Choose three)

A. network regionB. gateway node nameC. node nameD. duplicate node nameE. link

Correct Answer: ACESection: (none)Explanation


QUESTION 44Which three procedures are used to determine whether a gateway with a survivable remote server has lostits H.248 link (connection) to the main (primary) server? (Choose three)

A. Execute the Communication Manager command display alarms, to see whether the Link Loss Delaytimer has expired

B. Execute the Communication Manager command display alarms, to see whether the No Service TimeoutTimer (NSTT) has expired

C. Execute the SAT command List media-gateway from the remote survivable server, to determinewhether the media gateway is registered with a survivable server

D. Execute the SAT command status media-gateways, to determine which media gateways are notregistered to the main server

E. Execute the command status H.248 line from the remote gateway, to determine whether the link to themain server is active


Explanation/Reference:1. list media-gatewaylist media-gateway [ type x ] [ region # ] [ schedu le ]Use list media-gateway from the primary server to see all administered media gateways.

Action/Object Qualifier Qualifier Descriptionlist type x Type of media-gateway (g 250, etc.)media-gateway region # region number 2. status media-gatewaysUse status media-gateways to see the alarm status of the administered Media Gateways.status media-gateways lists alarms, busyout summary, and H.248 link status for the mediagateways. The alarms are associated only with board-type alarms on the Media Modules.Status for VoIP and MGP alarms are provided via the Media Gateway Processor CLI.

3. test media-gatewaytest media-gateway x

Use test media-gateway from the primary server to run a board audit, an H.248 link audit,and an H.248 context audit.• The link (test 1527) and context audits run successfully and no error codes are associatedwith the tests. Use test media-gateway to run an H.248 link audit when there is analarm against a Media Gateway for being unregistered when it actually is registered. Ifthere is an interchange while a media gateway is registering or unregistering, the alarmmay appear and status media-gateway and list media-gateway may incorrectlyshow the media gateway to be unregistered.• Results of test media-gateway vary depending on configuration of the media gateway

QUESTION 45A user at extension 1111 complains that when dialing extension 2222 the call is xxxxxxxx made areconnected as expected, There is not a display on the phone While at the xxxxxx. Which command identifies the reason this phone call is behaving in this unexpected xxxxxxxxx?

A. list trace station 1111B. list trace station 3333C. status station 1111D. display station 3333


Explanation/Reference:You can also run the real-time list trace station xxxx command to display the controlinformation for each station:Type: list trace station 1001 followed by Enter, and then place a call from 1001 to1002. Press F1 [CANCEL ] to stop the trace.

QUESTION 46A user at a remote branch location is registered to a G450 media gateway connected via ProcessorEthernet (PE) to a main Communication Manager in the core . They report that they are no longer able to

place calls to users at the core. Which three procedures can be used to diagnose the source of theproblem? (Choose three)

A. Confirm that the Registered field on the Communication Manager display media-gateway form is set toy.

B. Confirm that the PE interface is active by executing the Communication Manager display processor-Ethernet command and confirm that the Allow H. 248 Gateway field is set to y.

C. Use the show mgc command on the media gateway to confirm that the IP address of the PE enabledserver at the core is administered as the primary controller of the media gateway

D. Use the list registered-ip-stations command on the Communication Manager to determine whether theuser on the media gateway is registered

E. Use the list survivable processor command to confirm that the survivable server is registered to themain Communication Manager in the core

Correct Answer: ADESection: (none)Explanation

Explanation/Reference:A. From the ASA command line, type: display media-gateway 1 and press Enter to verify the gatewayadministration:

D. From the ASA command line, type: list registered-ip-stations and press Enter:

E. Type: list survivable-processor command again to ensure that the Survivable Remote Simplex serverhas updated its translations .

QUESTION 47How is the status of virtual machines (eg.DOM-0, CDOM-0, CM6.0) on S8800 server checked?

A. by going to the home page of Console DomainB. by going to the home page of Avaya Communication ManagerC. by going to the home page of Dom 0D. by using link on Internet Explorer->http://Cdom_lpaddr/VM


Explanation/Reference:Use the Server > Process Status page to ensure that all of the processes come up

Use the Server > Process Status page to ensure that all of the processes, especially CommunicationManager, are UP.

QUESTION 48Which Circuit Pack provides an IP Server Interface in an Avaya G650 Gateway?

A. TN2312AP

B. TN2342ACC. MM711D. MM714


Explanation/Reference:TN2312AP IPSI CapabilitiesThe TN2312AP IPSI always resides in the tone clock slot on a media gateway and uses a 10/100 BaseTinterface to connect to:The Server A laptop computer connected to the server through a services port

The Avaya TN2312AP IPSI provides the following functions:PN clock generation and synchronization for Stratum 4 type II only PN tone generation PN tone detection, global call classification, and international protocols Processing of product serial numbers for license file activation Environmental maintenance, only on a G650 Media Gateway

TN2312AP IPSI Gateway Compatibility

The IPSI is compatible with the CMC1, MCC1, SCC1, G600, and G650

QUESTION 49A technician is asked to retrieve a maintenance log for CMM that shows the information from 8:00 AM to5:00 PM local time that day. Which shell command should be executed to retrieve the maintenance log?

A. show maint log 0800 101010B. displog -l maint -d 10/10/10 08:00C. display log for maint 101010 0800D. print -1 maint -d 08:00 10/10/10


Explanation/Reference:The Avaya S3420 Messaging Application Server provides two system logs related specifically to events anderrors.

Administrator log This contains events and errors that will likely be of more interest to systemadministrators. Maintenance events log This contains events and errors generally of interest only to technical servicesand development personnel.

Procedure 1: Displaying an Event and Error Log on t he MAS

1. On your Windows desktop, click the Start > Run menu command. The system displays the Run dialogbox.1. In the Open field, type command or cmd and click OK. The system displays the MS-DOS Promptwindow.1. At the DOS prompt, enter one of the following commands, depending on the event and error log youwant to view:

To view the administrator log, enter displog -l admin . To view the maintenance events log, enter displog -l maint . You may wish to limit the number of entries the system displays. Otherwise, you may have to siftthrough hundreds or thousands of entries. To do this, you can modify the displog command to retrieverecords for designated days or times, for example: If you wanted to view the events log for today from 3:00 p.m. to the current time, you would enter:

displog -l maint -d15:00 . If you wanted to view the administrator log for all of today, starting from midnight, you would enter: displog -l admin -dmm/dd/yy (where mm/dd/yy is today’s date). If you wanted to view the events log for all events starting from a certain day at 8:00 a.m. to the present,you would enter:displog -l maint -d"mm/dd/yy 08:00 " (where mm/dd/yy is the starting date for the records you want toview).

QUESTION 50Which MAC address is recommended for the license file?

A. the MAC Address of the Console domainB. the MAC Address of the CM eth0 portC. the MAC Address of the CM host nameD. the MAC Address of the DOM0



QUESTION 51A newly installed main CM 6.0 server indicates it is in license error mode. A technician checks again 45minutes later and it is still in error mode. The license was installed from the System Management Interface (SMI). Which statement describes thereason for the error mode?

A. The installer used the wrong interface to install the license and it is therefore not installed.B. The server cannot communicate with the IPSI or Media Gateway whose serial number was used in the

license file.C. The license audit runs every 60 minutes and the error will be resolved in 15 minutes.D. The installer loaded a license for one of the survivable servers, not the main server, and the IPSIs,

Media Gateways, and/or IP phones have registered to it



CM license file installed and managed on WebLM server in System Platform Managment ConsoleNo license files necessary for Survivable Core (formerly ESS) and Survivable Remote (formerly LSP)servers

QUESTION 52To backup Communication Manager, what two choices does the customer have?(Choose two)

A. Backup/RestoreB. Backup NowC. Backup LaterD. Schedule BackupE. Backup/Restore Later



QUESTION 53A user at extension 1111 complains that when dialing extension 2222, the call is unexpectedly answered bythe person at extension 3333. All other calls made are connected as expected. There is not a display on thephone. While at the SAT, the technician has the user repeat the call to extension 2222. Which commandshows the reason this phone call is behaving in this unexpected way?

A. list trace station 1111B. list trace station 3333C. status station 1111D. display station 3333


Explanation/Reference:You can also run the real-time list trace station xxxx command to display the controlinformation for each station:Type: list trace station 1001 followed by Enter, and then place a call from 1001 to1002. Press F1 [CANCEL ] to stop the trace.

QUESTION 54Which greeting should be received when you are calling the Messaging hunt group?

A. Welcome to Audix.B. Welcome to messaging.C. Your call is being answered by Audix.D. Please leave a message after the tone.


Explanation/Reference:In this step, you will verify that the coverage path is configured correctly by placing a call from 6000 to6001 and allowing the call to go to coverage.

From Extension 6000, call Extension 6001.Your test is successful when you hear the greeting, “Your call is beinganswered by AUDIX”.If you do not hear the “Your call is being answered by AUDIX” greeting, then you need to troubleshootyour implementation.

QUESTION 55What two pieces of information does the Product Licensing and Delivery System (PLDS) require to beentered for a license file to be generated?( Choose two)

A. serial numberB. license activation codeC. MAC addressD. platform type

Correct Answer: BCSection: (none)

Explanation

Explanation/Reference:Product licenses are tied to the host ID (MAC address) of the System Platform.

QUESTION 56Which statement describes the action to assure the CM_Simplex Template was installed correctly?

A. From a browser logged into the System Management Console, verify cm and utility server appear andthe Application State is running.

B. From a browser, using the Communication Manager IP address, successfully log into theCommunication Manager System Management Interface (SM)

C. When monitoring the template installation workflow status, verify the message. "Wizard completedsuccessfully" displays.

D. From a browser logged into Communication Manager, select Administration Server (Maintenance )Server Process Status, click on View, and verify CommunicaMgr appears



QUESTION 57Which two statements regarding shuffling and hairpinning are true?(Choose two)

A. Hairpinning does not use media processor resources.B. The Audio Connection Type field on the Communication Manager status station form can be used to

determine whether a call is shuffledC. A call between a DCP endpoint and an H 323 endpoint can be shuffledD. Shuffling releases media processor resources


Explanation/Reference:Hairpinning & Shuffling Summary

HairpinningUnlike the IP-TDM-IP connectivity option, hairpinning requires that all media processingresources for a given call reside on a single TN2302AP or TN2602AP media processingcircuit pack or a single G350 or G700 Media Gateway Voip Media Module. A hairpinnedcall is originally set up as an IP-TDM-IP call, but once the set-up process is complete, noTDM resources are required. However, resources on the Media Processing circuit packor VoIP Media Module are required for the duration of the call. A Media Processingcircuit pack and a VoIP Media Module each house an on-board Central Processing Unit(CPU) and Digital Signal Processors (DSPs).

ShufflingA shuffled call relinquishes all TDM and media processing resources after call set-up.

Therefore, the media stream of a shuffled call traverses only an IP network. This is themost commonly used mode of connectivity between two IP endpoints in the samesystem.

QUESTION 58Which Avaya G450 Module provides 8 DCP ports?

A. MM711B. MM712C. TN7202D. TN2224


Explanation/Reference:Avaya MM712 Features

Provides 8 modular ports for 2-wire digital (DCP) telephones Ports are intended for in-building use only

CompatibilitySupported in G350, G450, and G700 Media Gateways

Avaya MM711 FeaturesAny of the 8 analog ports can be configured as: Loop start or ground start CO trunk Wink start or immediate start analog DID 2-wire analog outgoing CAMA E911 trunk Analog tip/ring port for devices such as single line telephones with or without LEDmessage waiting indicationSupports incoming caller ID (ICLID)

CompatibilitySupported in G350, G450, and G700 Media Gateways

QUESTION 59A network failure prevents communication between all the port networks (IPSIs) and their main CM server.What is the maximum number of port networks (IPSIs) that can register to a survivable remote embeddedserver?

A. no port networkB. 63 port networksC. 64 port networksD. 126 port networks



QUESTION 60Which three servers can be upgraded to Communication Manager Release 6.0? (Choose three.)

A. S8300CB. S8300DC. S8400

D. S8510E. S8800

Correct Answer: BDESection: (none)Explanation


QUESTION 61A customer has a Communication Manager R6.0 system with IP phones and older TDM phones, and saysthere is no dial tone for all of the IP Phones. All of the hardware has been verified to be working property. Which two steps can be taken to identify the cause of the problem? (Choose two)

A. Verity that the TN2602 Media Resource circuit pack has the correct IP settingsB. Verify that the Processor Ethernet mode is enabled in the serverC. Set a static IP address on a laptop and see if the server can be pingedD. Set a static IP address on a laptop and see if the TN2602 Media Resource circuit pack can be pinged

Correct Answer: ADSection: (none)Explanation

Explanation/Reference:At the prompt, type: list configuration circuit-pack TN2602 and press Enter: Note the Board Number locations of the Media Resource circuit packs in the system.

At the prompt type: status media-processor all and press Enter. Verify that all configured Media Processor Control Links and Ethernet Links are UP.

QUESTION 62To ensure that Communication Manager Messaging application is working. What are three tests that canbe performed? (Choose three)

A. Call one of the two station that you set as a subscriber to the messaging server, and let the call go tocoverage.

B. Leave a message on a covered call and verify that the Message Waiting Indicator (MVVI) lamp on the

receiving extension is litC. Call the station and after the call is answered leave a message.D. Call the messaging hunt group from any of the stations to ensure it is answeringE. Log into Communication Manager Messaging to verify CDOM is running

Correct Answer: ABDSection: (none)Explanation

Explanation/Reference:After you complete the administration steps for Communication Manager Messaging, youneed to test the implementation.

Call an extension to verify messaging coverage. Call the hunt group to access messaging (voice mail). Identify possible source of errors if the testing does not work.

Verify Coverage Test Goal

In this test, you verify that the cover path is administered correctly by calling anextension and letting the call go to cover.

Test Process During the administration process, you created two test extensions. You also created two subscriber mailboxes for these extensions.

1. Log in to the first extension. 2. Call the second extension. 3. Let the call go to cover. 4. Listen for the “Your call is being answered by AUDIX” greeting. 5. Leave a message. 6. Verify that the Messaging Waiting Indicator (MWI) lamp on the receiving extension is lit and hang up the

call.

Check: If you do not hear the AUDIX greeting, then you need to troubleshoot yourimplementation. Verify settings for the hunt group. Verify settings for the coverage path. Verify settings for the station. Verify the settings for the subscriber mailbox.

QUESTION 63Which statement describes how the Communication Messaging Application is enabled the first time afterthe installation?

A. Connect to the SAT terminal Login using craft and then enable messaging using the enable messagingcommand

B. Open the Communication Manager IP address using web browser. Login as craft, click installation, thenCommunication Manager Messaging and then click Enable

C. Open the Communication Manager IP address using web browser. Login as craft, click Administration,then Server(Maintenance). Then click Miscellaneous, then Messaging Software, and then click Enable.

D. Communication Manager Messaging is enabled by default after the installation.



QUESTION 64Through which two protocols can integration of the Communication Manager Messaging application 6.0with Communication Manager occur? (Choose two.)

A. H323/QSig protocolB. RTP protocolC. SSP protocolD. SIP protocol

Correct Answer: ADSection: (none)Explanation

Explanation/Reference:Here are the high-level steps for administering CM for CMM using the SAT interface:

Check H.323 customer options. Set Feature Access Codes (FACs) for messaging using the dial plan. Set feature parameters for messaging. Administer IP interfaces. Set parameters for system coverage.

You complete the same steps before beginning either the H.323 QSIG or the SIPintegration.

QUESTION 65An administrator has just installed a 9620 IP phone on an existing system. The command change ip-network-map is used to administer the phone into network region 100. All other phones are in networkregion 1.Like all other 9620 phones on this system, this one successfully gets IP address information from the oneDHCP server. However, the new phone fails to register with CM. Which two statements describe the cause of thisproblem? ( Choose two)

A. Neither PROCR nor CLANs were administered in network region 100B. There are no Medpros or H248 Media Gateways administered in network region 100C. Network region 100 is not configured to communicate with any other network regionsD. On the ip-interface form, someone recently set the field Allow H323 registrations to "n"



QUESTION 66Which statement describes how the licensed mailboxes are enable on Communication Manager MessagingApplication 6.0?

A. Mailboxes are enable in the Communication Manager 6.0 license fileB. Mailboxes are enable by a separate license that needs to be generated and deployed.C. Mailboxes are enabled by defaultD. Mailboxes are enabled in the system-parameters features form


Explanation/Reference:Tere are two license files – one for CM and one for CMM. Both Communication Manager and Communication Manager Messaging use WebLM forlicense management. WebLM is accessed through the System Platform Console Domain (cdom). Uses the MAC address of the server hosting WebLM for the license file host ID. Human readable, plain-text license files in XML format.

A 30-day grace period now applies for no license file present on new installation ormigration. This grace period means that you can complete the installation even if there areproblems with the license file.

Although the CMM software is installed as part of t he CM template, the CMMsoftware requires a separate License file in order for its features to be functional.

QUESTION 67On a media gateway G450, into which slot does the S8300D server blade need to be inserted?


A. V1B. V2C. V4D. V8


Explanation/Reference:Media Module - Media ModuleMM340 - V3, V4, V8MM342 - V3, V4, V8MM710 - Any Media Slot, V1 - V8MM711 - Any Media Slot, V1 - V8Mm712 - Any Media Slot, V1 - V8MM714 - Any Media Slot, V1 - V8MM716 - Any Media Slot, V1 - V8MM717 - Any Media Slot, V1 - V8MM720 - Any Media Slot, V1 - V8MM722 - Any Media Slot, V1 - V8S8300D - V1

QUESTION 68Which two hardware components support CM_ survRemote template?( Choose two)

A. S8730 Server with 8 GB RAMB. S8800 ServerC. S8510 Server with 8 GB RAMD. S8300D Server

Correct Answer: BCSection: (none)Explanation


QUESTION 69In which two modes is Communication Manager Release 6.0 deployed? (Choose two.)

A. Feature ServerB. Signaling ServerC. Evolution ServerD. System Manager Server



This diagram shows the three Communication Manager core servers: 1. In the purple area at the top, there are two instances of CM Core Duplex on duplicated servers: the one on the left functions as a Feature Server to support SIP endpoints, and the one on the rightfunctions as an Evolution Server for non-SIP configurations. 2. Also in the top center is the standalone CM Core Simplex server. 3. At the bottom right is a non-SIP branch with the CM Core Embedded server that runs on the S8300D

server in slot 1 of a G430/G450 Gateway.

QUESTION 70A customer has selected Avaya Aura CM_survremote_embedded template. Wich Avaya server should beused?

A. S8730 Server 8 GB RAMB. S8800 ServerC. S8510 Server with 8 GB RAMD. S8300D Server



Avaya.Certkey.6002-1.v2014-06-16.by.GRETCHEN - · PDF...

Documents

Transcript of Avaya.Certkey.6002-1.v2014-06-16.by.GRETCHEN - · PDF...