Avaya Command Line Interface Commands Reference

Avaya Command Line InterfaceCommands Reference

Avaya Command Line Interface Commands Reference

Introduction

This guides describes the Avaya Command Line Interface (ACLI) commands for the configuration of various features in AvayaVirtual Services Platform 7000 Series for the 10.4 release.

This document provides two different ways of navigating ACLI command documentation.

alphabetically Each command is listed corresponding to the first letter of the command.command mode Each command mode page has a list of commands that are available in that mode. Each page is organizedalphabetically for those commands in that mode.

Use the 'find-in-page' function of the browser to search for a command based on the page you are viewing. Most browsers launch'find' using CTRL+F.

Notice

While reasonable efforts have been made to ensure that the information in this document is complete and accurate at the time ofprinting, Avaya assumes no liability for any errors. Avaya reserves the right to make changes and corrections to the information inthis document without the obligation to notify any person or organization of such changes.

Documentation disclaimer

Avaya shall not be responsible for any modifications, additions, or deletions to the original published version of this documentationunless such modifications, additions, or deletions were performed by Avaya. End User agree to indemnify and hold harmlessAvaya, Avaya's agents, servants and employees against all claims, lawsuits, demands and judgments arising out of, or inconnection with, subsequent modifications, additions or deletions to this documentation, to the extent made by End User.

Link disclaimer

Avaya is not responsible for the contents or reliability of any linked Web sites referenced within this site or documentation(s)provided by Avaya. Avaya is not responsible for the accuracy of any information, statement or content provided on these sites anddoes not necessarily endorse the products, services, or information described or offered within them. Avaya does not guaranteethat these links will work all the time and has no control over the availability of the linked pages.

Warranty

Avaya provides a limited warranty on this product. Refer to your sales agreement to establish the terms of the limited warranty. Inaddition, Avaya’s standard warranty language, as well as information regarding support for this product, while under warranty, isavailable to Avaya customers and other parties through the Avaya Support Web site: http://www.avaya.com/support. Please notethat if you acquired the product from an authorized Avaya reseller outside of the United States and Canada, the warranty isprovided to you by said Avaya reseller and not by Avaya.

License types

THE SOFTWARE LICENSE TERMS AVAILABLE ON THE AVAYA WEBSITE, HTTP://SUPPORT.AVAYA.COM/LICENSEINFO/AREAPPLICABLE TO ANYONE WHO DOWNLOADS, USES AND/OR INSTALLS AVAYA SOFTWARE, PURCHASED FROM AVAYA INC., ANYAVAYA AFFILIATE, OR AN AUTHORIZED AVAYA RESELLER (AS APPLICABLE) UNDER A COMMERCIAL AGREEMENT WITH AVAYAOR AN AUTHORIZED AVAYA RESELLER. UNLESS OTHERWISE AGREED TO BY AVAYA IN WRITING, AVAYA DOES NOT EXTENDTHIS LICENSE IF THE SOFTWARE WAS OBTAINED FROM ANYONE OTHER THAN AVAYA, AN AVAYA AFFILIATE OR AN AVAYAAUTHORIZED RESELLER, AND AVAYA RESERVES THE RIGHT TO TAKE LEGAL ACTION AGAINST YOU AND ANYONE ELSE USINGOR SELLING THE SOFTWARE WITHOUT A LICENSE. BY INSTALLING, DOWNLOADING OR USING THE SOFTWARE, ORAUTHORIZING OTHERS TO DO SO, YOU, ON BEHALF OF YOURSELF AND THE ENTITY FOR WHOM YOU ARE INSTALLING,DOWNLOADING OR USING THE SOFTWARE (HEREINAFTER REFERRED TO INTERCHANGEABLY AS "YOU" AND "END USER"),AGREE TO THESE TERMS AND CONDITIONS AND CREATE A BINDING CONTRACT BETWEEN YOU AND AVAYA INC. OR THE

http://support.avaya.com/LICENSEINFO/

APPLICABLE AVAYA AFFILIATE ("AVAYA").

Copyright

Except where expressly stated otherwise, no use should be made of materials on this site, the Documentation(s) and Product(s)provided by Avaya. All content on this site, the documentation(s) and the product(s) provided by Avaya including the selection,arrangement and design of the content is owned either by Avaya or its licensors and is protected by copyright and otherintellectual property laws including the sui generis rights relating to the protection of databases. You may not modify, copy,reproduce, republish, upload, post, transmit or distribute in any way any content, in whole or in part, including any code andsoftware. Unauthorized reproduction, transmission, dissemination, storage, and or use without the express written consent ofAvaya can be a criminal, as well as a civil, offense under the applicable law.

Third-party components

Certain software programs or portions thereof included in the Product may contain software distributed under third partyagreements ("Third Party Components"), which may contain terms that expand or limit rights to use certain portions of theProduct ("Third Party Terms"). Information regarding distributed Linux OS source code (for those Products that have distributedthe Linux OS source code), and identifying the copyright holders of the Third Party Components and the Third Party Terms thatapply to them is available on the Avaya Support Web site: avaya.com/support/Copyright/.

Trademarks

The trademarks, logos and service marks (“Marks”) displayed in this site, the documentation(s) and product(s) provided by Avayaare the registered or unregistered Marks of Avaya, its affiliates, or other third parties. Users are not permitted to use such Markswithout prior written consent from Avaya or such third party which may own the Mark. Nothing contained in this site, thedocumentation(s) and product(s) should be construed as granting, by implication, estoppel, or otherwise, any license or right inand to the Marks without the express written permission of Avaya or the applicable third party.

Avaya is a registered trademark of Avaya Inc.

All other trademarks are the property of their respective owners.

Technical support

Avaya provides a telephone number for you to use to report problems or to ask questions about your product. The supporttelephone number is 1-800-242-2121 in the United States. For additional support telephone numbers, see the Avaya Web site:avaya.com/support.

If you purchased a service contract for your Avaya product from a distributor or authorized reseller, contact the technical supportstaff for that distributor or reseller for assistance.

Documentation support

For the most current versions of documentation, see the Avaya Support Web site: avaya.com/support.

Avaya Virtual Services Platform 7000 Series Release 10.4NN47202-600 Avaya Command Line Interface Commands Reference

Version 04.01 July 2015©Avaya Inc. 2015 All Rights Reserved.

Avaya.com/support

http://www.avaya.com/support/Copyright/

http://www.avaya.com/support



Alphabetical command listing

Home | Command modes | Alphabetical listing

Alphabetized list of commands

A | B | C | D | E | F | H | I | J | L | M | N | O | P | Q | R | S | T | U | V | W

A - 16 commandsB - 4 commandsC - 37 commandsD - 7 commandsE - 4 commandsF - 17 commandsH - 5 commandsI - 166 commandsJ - 1 commandsL - 31 commandsM - 23 commandsN - 5 commandsO - 3 commandsP - 5 commandsQ - 23 commandsR - 26 commandsS - 370 commandsT - 14 commandsU - 6 commandsV - 16 commandsW - 2 commands



Avaya.com/support


Command mode index


Command mode index

The following command modes are available. Select the command mode to see a list of commands available in that mode.

Application ConfigurationEthernet Interface ConfigurationGlobal ConfigurationIGMP Filter Profile Configuration modeISIS Router ConfigurationLoopback Interface ConfigurationMgmt Interface ConfigurationMLT Interface ConfigurationOSPF Router ConfigurationPrivileged EXECPrivileged ExecutiveRIP Router ConfigurationUser EXECUser ExecutiveVLAN Interface ConfigurationVRRP Router Configuration

Back to top



Avaya.com/support


Commands starting with A


Commands starting with A organized alphabetically


accept adv-rtrapplicationareaarea <A.B.C.D> rangearea virtual-linkarea virtual-link message-digest-keyarpas-boundary-routerasset-idaudit log noerase enableaudit log saveauto-negotiation-advertisementsauto-pvidautosave enableautotopologyauto-vlink




Avaya.com/support


Commands starting with B


Commands starting with B organized alphabetically


bannerblink-ledsbootbrouter




Avaya.com/support


Commands starting with C


Commands starting with C organized alphabetically


cfm spbm enablecfm spbm level <0-7>cfm spbm mepid <1-8191>clear arp-cacheclear audit logclear ip-blockingclear ip dhcp-snoopingclear ip forward-protocolclear ip igmpclear ip ospfclear ipv6clear ipv6 destinationcacheclear ipv6 destinationcache (Ethernet Interface Configuration)clear ipv6 dhcp-relayclear ipv6 neighbor-cacheclear isis lsdbclear isis statsclear loggingclear mac-address-tableclear sshcclear stack port-statisticsclear-statsclear system last-exceptioncliclockclock sourceclock summer-timeclock sync-rtc-with-ntp enableclock time-zoneconfigurecopy configcopy nvramcopy running-configcopy sftpcopy tftpcopy usbcsnp-interval




Avaya.com/support


Commands starting with D


Commands starting with D organized alphabetically


ddi-loggingdefault-costdefault-metricdiagnostics-quick-mode enabledisabledownloadduplex




Avaya.com/support


Commands starting with E


Commands starting with E organized alphabetically


edmenableendexit




Avaya.com/support


Commands starting with F


Commands starting with F organized alphabetically


fafa authentication-keyfa extended-loggingfa message-authenticationfa port-enablefa proxyfa standalone-proxyfa timeoutfa uplinkfa vlanfa zero-touchfa zero-touch-optionsfcoe controllerfcoe controller-accessfcoe oper-modefcoe profileflowcontrol




Avaya.com/support


Commands starting with H


Commands starting with H organized alphabetically


helphost-routehttp-porthttps-onlyhttps-port




Avaya.com/support


Commands starting with I


Commands starting with I organized alphabetically


installinterface Ethernetinterface loopbackinterface mgmtinterface mltinterface vlanip address (Global Configuration)ip address (VLAN Interface Configuration)ip arp-inspection (Ethernet Interface Configuration)ip arp-inspection (Global Configuration)ip arp-proxyip blocking-modeip bootpip default-gatewayip dhcp client leaseip dhcp-relay (Ethernet Interface Configuration)ip dhcp-relay (Global Configuration)ip dhcp-relay (VLAN Interface Configuration)ip dhcp-snooping bindingip dhcp-snooping (Ethernet Interface Configuration)ip dhcp-snooping external-saveip dhcp-snooping external-save restoreip dhcp-snooping (Global Configuration)ip directed-broadcast enableip directed-broadcast (VLAN Interface Configuration)ip domain-nameip forward-protocol udp (Global Configuration)ip forward-protocol udp (VLAN Interface Configuration)ip fwd-nh (Global Configuration)ip fwd-nh (VLAN Interface Configuration)ip igmpip igmp filterip igmp fluship igmp last-member-query-intervalip igmp mrouterip igmp profileip igmp proxyip igmp query-intervalip igmp query-max-responseip igmp robust-valueip igmp router-alertip igmp send-queryip igmp snoopingip igmp versionip ipfix collectorip ipfix enableip ipfix (Ethernet Interface Configuration)ip ipfix flush portip ipfix (Global Configuration)

ip ipfix slotip (Loopback Interface Configuration)ip mgmt addressip mgmt default-gatewayip mgmt limitip mgmt netmaskip mgmt routeip mgmt shutdownip mgmt shutdown-intervalipmgrip name-serverip ospf advertise-when-down enable (Ethernet Interface Configuration)ip ospf advertise-when-down enable (VLAN Interface Configuration)ip ospf apply acceptip ospf apply redistributeip ospf area (Ethernet Interface Configuration)ip ospf area (VLAN Interface Configuration)ip ospf authentication-key (Ethernet Interface Configuration)ip ospf authentication-key (VLAN Interface Configuration)ip ospf authentication-type (Ethernet Interface Configuration)ip ospf authentication-type (VLAN Interface Configuration)ip ospf cost (Ethernet Interface Configuration)ip ospf cost (VLAN Interface Configuration)ip ospf dead-interval (Ethernet Interface Configuration)ip ospf dead-interval (VLAN Interface Configuration)ip ospf enable (Ethernet Interface Configuration)ip ospf enable (VLAN Interface Configuration)ip ospf hello-interval (Ethernet Interface Configuration)ip ospf hello-interval (VLAN Interface Configuration)ip ospf message-digest-key (Ethernet Interface Configuration)ip ospf message-digest-key (VLAN Interface Configuration)ip ospf mtu-ignore enable (Ethernet Interface Configuration)ip ospf mtu-ignore enable (VLAN Interface Configuration)ip ospf network (Ethernet Interface Configuration)ip ospf network (VLAN Interface Configuration)ip ospf primary-md5-key (Ethernet Interface Configuration)ip ospf primary-md5-key (VLAN Interface Configuration)ip ospf priority (Ethernet Interface Configuration)ip ospf priority (VLAN Interface Configuration)ip ospf retransmit-interval (Ethernet Interface Configuration)ip ospf retransmit-interval (VLAN Interface Configuration)ip ospf transit-delay (Ethernet Interface Configuration)ip ospf transit-delay (VLAN Interface Configuration)ip prefix-listip rip advertise-when-down enable (Ethernet Interface Configuration)ip rip advertise-when-down enable (VLAN Interface Configuration)ip rip auto-aggregation enable (Ethernet Interface Configuration)ip rip auto-aggregation enable (VLAN Interface Configuration)ip rip cost (Ethernet Interface Configuration)ip rip cost (VLAN Interface Configuration)ip rip default-listen enable (Ethernet Interface Configuration)ip rip default-listen enable (VLAN Interface Configuration)ip rip default-supply enable (Ethernet Interface Configuration)ip rip default-supply enable (VLAN Interface Configuration)ip rip enable (Ethernet Interface Configuration)ip rip enable (VLAN Interface Configuration)ip rip holddown (Ethernet Interface Configuration)ip rip holddown (VLAN Interface Configuration)ip rip in-policy (Ethernet Interface Configuration)ip rip in-policy (VLAN Interface Configuration)ip rip listen enable (Ethernet Interface Configuration)ip rip listen enable (VLAN Interface Configuration)ip rip out-policy (Ethernet Interface Configuration)ip rip out-policy (VLAN Interface Configuration)ip rip poison enable (Ethernet Interface Configuration)

ip rip poison enable (VLAN Interface Configuration)ip rip proxy-announce enable (Ethernet Interface Configuration)ip rip proxy-announce enable (VLAN Interface Configuration)ip rip receive (Ethernet Interface Configuration)ip rip receive (VLAN Interface Configuration)ip rip send (Ethernet Interface Configuration)ip rip send (VLAN Interface Configuration)ip rip supply enable (Ethernet Interface Configuration)ip rip supply enable (VLAN Interface Configuration)ip rip timeout (Ethernet Interface Configuration)ip rip timeout (VLAN Interface Configuration)ip rip triggered enable (Ethernet Interface Configuration)ip rip triggered enable (VLAN Interface Configuration)ip routeip routing (Global Configuration)ip routing (VLAN Interface Configuration)ip source-interfaceipv6ipv6 addressipv6 autoconfigipv6 default-gatewayipv6 dhcp-relay (Global Configuration)ipv6 dhcp-relay (VLAN Interface Configuration)ipv6 icmp addr-unreachipv6 icmp block-multicast-repliesipv6 icmp error-intervalipv6 icmp error-quotaipv6 icmp port-unreachipv6 icmp unreach-msgipv6 interface (Loopback Interface Configuration)ipv6 interface (VLAN Interface Configuration)ipv6 mgmt addressipv6 mgmt default-gatewayipv6 mgmt interfaceipv6 nd prefixipv6 nd prefix-interfaceipv6 nd (VLAN Interface Configuration)ipv6 neighboripv6 routeipv6 tunnelip verify sourceip vrrpip vrrp addressi-sidisis (Ethernet Interface Configuration)isis hello-auth (Ethernet Interface Configuration)isis l1-dr-priority (Ethernet Interface Configuration)isis l1-hello-interval (Ethernet Interface Configuration)isis l1-hello-multiplier (Ethernet Interface Configuration)isis spbm (Ethernet Interface Configuration)istis-type




Avaya.com/support


Commands starting with J


Commands starting with J organized alphabetically


jumbo-frames




Avaya.com/support


Commands starting with L


Commands starting with L organized alphabetically


l2 pingl2 traceroutel2 tracetreelacp aggregationlacp clear-statslacp key (Ethernet Interface Configuration)lacp key (Global Configuration)lacp modelacp port-modelacp prioritylacp smlt-sys-idlacp system-prioritylacp timeout-timelink-state grouplldp config-notificationlldp location-identificationlldp med-fast-startlldp med-network-policieslldp notification-intervallldp reinit-delaylldp statuslldp tx-delaylldp tx-hold-multiplierlldp tx-intervallldp tx-tlvlldp vendor-specific avaya call-serverlldp vendor-specific avaya file-serverlldp vendor-specific (Ethernet Interface Configuration)logginglogging remotelogout




Avaya.com/support


Commands starting with M


Commands starting with M organized alphabetically


mac-address-tablemac-security auto-learningmac-security disablemac-security enablemac-security (Ethernet Interface Configuration)mac-security filteringmac-security intrusion-detectmac-security intrusion-timermac-security learningmac-security learning-portsmac-security mac-address-tablemac-security mac-da-filtermac-security security-listmac-security snmp-lockmanual-areamanualtrigger ip rip interface vlanmaximum-pathmax-lsp-gen-intervalmda enablemetricmltmlt shutdown-ports-on-disable enablemlt spanning-tree




Avaya.com/support


Commands starting with N


Commands starting with N organized alphabetically


namenetwork (OSPF Router Configuration)network (RIP Router Configuration)ntpntp server




Avaya.com/support


Commands starting with O


Commands starting with O organized alphabetically


ospf maximum-pathoverloadoverload-on-startup




Avaya.com/support


Commands starting with P


Commands starting with P organized alphabetically


passwordpingping-virtual-addressport-mirroringpsnp-interval




Avaya.com/support


Commands starting with Q


Commands starting with Q organized alphabetically


qos actionqos agentqos classifierqos classifier-blockqos clear-statsqos egressmapqos if-action-extensionqos if-assign (Ethernet Interface Configuration)qos if-assign (Global Configuration)qos if-groupqos if-queue-shaperqos if-shaperqos ingressmapqos ip-elementqos l2-elementqos meterqos policyqos queue-set-assignmentqos system-elementqos traffic-profile classifierqos traffic-profile setquickconfig enablequickconfig start-recording




Avaya.com/support


Commands starting with R


Commands starting with R organized alphabetically


radius accounting enableradius reachabilityradius-serverradius use-management-iprangerate-limitrear-port moderedistributereloadrenewrenumber unitrestore factory-defaultretransmit-lsp-intervalrfc1583-compatibilityrip maximum-pathrmon alarmrmon eventrmon historyrmon statsroute-maprouter-idrouter isisrouter ospfrouter riprouter vrrprun spbm




Avaya.com/support


Commands starting with S


Commands starting with S organized alphabetically


save configscript runscript uploadserial-consoleserial-security enablesflowsflow collectorsflow (Ethernet Interface Configuration)sftp-servershow application slamon agentshow arpshow arp-tableshow audit logshow auto-negotiation-advertisementsshow auto-negotiation-capabilitiesshow auto-pvidshow autosaveshow autotopologyshow bannershow bootshow broutershow cfm spbmshow clishow clockshow config-networkshow cpu-utilizationshow ddi-loggingshow diagnostics-quick-modeshow ecmpshow edm help-file-pathshow environmentalshow fashow fa agentshow fa elementshow fa i-sidshow fa port-enableshow fa uplinkshow fa vlanshow fa zero-touch-optionsshow fcoeshow flashshow http-portshow https-onlyshow https-portshow interfacesshow interfaces admin-disabledshow interfaces admin-enabledshow interfaces gbic-infoshow interfaces link-down

show interfaces link-upshow interfaces loopbackshow interfaces namesshow interfaces namesshow interfaces <port>show interfaces verboseshow ipshow ip addressshow ip arp-inspectionshow ip arp-proxyshow ip-blockingshow ip blocking-modeshow ip bootpshow ip default-gatewayshow ip default-ttlshow ip dhcp client leaseshow ip dhcp-relayshow ip dhcp-snooping bindingshow ip dhcp-snooping external-saveshow ip dhcp-snooping interfaceshow ip dhcp-snooping vlanshow ip directed-broadcastshow ip dnsshow ip forward-protocolshow ip igmpshow ip igmp cacheshow ip igmp groupshow ip igmp group-extshow ip igmp interfaceshow ip igmp profileshow ip igmp router-alertshow ip igmp snoopingshow ip igmp snoop-querier-addrshow ip ipfixshow ip ipfix collectorshow ip ipfix interfaceshow ip ipfix slotshow ip ipfix tableshow ip mgmtshow ipmgrshow ip netstatshow ip ospfshow ip ospf acceptshow ip ospf areashow ip ospf area-rangeshow ip ospf aseshow ip ospf authenticationshow ip ospf default-costshow ip ospf host-routeshow ip ospf ifstatsshow ip ospf int-authshow ip ospf interfaceshow ip ospf int-timersshow ip ospf lsdbshow ip ospf neighborshow ip ospf redistributeshow ip ospf statsshow ip ospf timershow ip ospf virtual-linkshow ip ospf virtual-neighborsshow ip prefix-listshow ip ripshow ip routeshow ip routingshow ip source-interface

show ipv6 addressshow ipv6 default-gatewayshow ipv6 default-routers (Privileged Executive)show ipv6 default-routers (User Executive)show ipv6 destinationcache (Privileged Executive)show ipv6 destinationcache (User Executive)show ipv6 dhcp-relayshow ipv6 globalshow ipv6 interfaceshow ipv6 mgmtshow ipv6 mld-host-cacheshow ipv6 mld-host-cache (Privileged Executive)show ipv6 ndshow ipv6 nd-prefixshow ipv6 neighborshow ipv6 routeshow ipv6 tcpshow ipv6 tunnelshow ipv6 udpshow ip vrrpshow ip vrrp addressshow ip vrrp interfaceshow i-sidshow isis adjacenciesshow isis int-authshow isis int-ckt-levelshow isis int-countersshow isis interfaceshow isis int-l1-cntl-pktsshow isis int-timersshow isis lsdbshow isis manual-areashow isis netshow isis spbm i-sidshow isis spbm multicast-fibshow isis spbm nick-nameshow isis spbm unicast-fibshow isis spbm unicast-treeshow isis statisticsshow isis system-idshow istshow jumbo-framesshow lacp aggrshow lacp debugshow lacp keyshow lacp portshow lacp port-modeshow lacp statsshow lacp systemshow link-stateshow lldpshow lldp local-sys-datashow lldp med-network-policiesshow lldp mgmt-sys-datashow lldp neighborshow lldp neighbor-mgmt-addrshow lldp pdu-tlv-sizeshow lldp portshow lldp rx-statsshow lldp statsshow lldp tx-statsshow lldp tx-tlvshow lldp vendor-specific avayashow loggingshow mac-address-table

show mac-address-table addressshow mac-address-table aging-timeshow mac-address-table dynamicshow mac-address-table mltshow mac-address-table portshow mac-address-table spbmshow mac-address-table staticshow mac-address-table vidshow mac-securityshow mdashow memory-utilizationshow mgmt-port statusshow mltshow mlt hash-calcshow ntpshow nvram blockshow passwordshow port-mirroringshow port-statisticsshow qos actionshow qos agentshow qos capabilityshow qos classifiershow qos classifier-blockshow qos diagshow qos egressmapshow qos if-action-extensionshow qos if-assignshow qos if-groupshow qos if-queue-shapershow qos if-shapershow qos ingressmapshow qos ip-elementshow qos l2-elementshow qos metershow qos policyshow qos portshow qos queue-setshow qos queue-set-assignmentshow qos statisticsshow qos system-elementshow qos traffic-profileshow quickconfigshow radiusshow radius-servershow rate-limitshow rear-portshow rmon alarmshow rmon ethernetshow rmon eventshow rmon historyshow rmon statsshow roleshow route-mapshow running-configshow scriptshow serial-consoleshow serial-securityshow sflowshow sflow collectorshow sflow interfaceshow sftp-servershow slppshow slpp-guardshow smlt

show snmp-servershow sntpshow spanning-treeshow spbmshow sshshow sshcshow sslshow stack auto-unit-replacementshow stack auto-unit-replacement-imageshow stack-cable-infoshow stack forced-modeshow stack healthshow stack-infoshow stack-monitorshow stack reboot-on-failureshow stack retry-countshow storm-controlshow sys-infoshow systemshow tacacsshow techshow telnet-accessshow telnet sessionsshow terminalshow tftp-servershow traceshow usb-filesshow usb-host-portshow usernameshow vlacpshow vlanshow vlan configcontrolshow vlan dhcp-relayshow vlan idshow vlan igmpshow vlan interfaceshow vlan ipshow vlan i-sidshow vlan mgmtshow vlan multicastshow vlan remote-spanshow vlan summaryshow vlan typeshow vlan voice-vlanshow web-servershow whoshutdown (Ethernet Interface Configuration)shutdown (Privileged EXEC)slamon agent-comm-portslamon agent ip addressslamon agent portslamon clislamon cli-timeoutslamon cli-timeout-modeslamon ntrslamon oper-modeslamon refuse-server-testsslamon RTPslamon server-bypassslamon server ip addressslamon server portslpp (Ethernet Interface Configuration)slpp (Global Configuration)slpp-guard (Ethernet Interface Configuration)slpp-guard (Global Configuration)

smlt (Ethernet Interface Configuration)smlt (MLT Interface Configuration)snmp-server bootstrapsnmp-server communitysnmp-server contactsnmp-server disablesnmp-server enablesnmp-server hostsnmp-server locationsnmp-server namesnmp-server notification-controlsnmp-server notify-filtersnmp-server usersnmp-server viewsnmp trapsntp enablesntp serversntp sync-intervalsntp sync-nowspanning-tree 802dot1d-port-compliance enablespanning-tree add-vlanspanning-tree bpdu-filtering (Ethernet Interface Configuration)spanning-tree bpdu-filtering ignore-self (Global Configuration)spanning-tree cost-calc-modespanning-tree (Ethernet Interface Configuration)spanning-tree forward-timespanning-tree hello-timespanning-tree max-agespanning-tree modespanning-tree multicast-addressspanning-tree port-modespanning-tree priorityspanning-tree remove-vlanspanning-tree stpspanning-tree tagged-bpduspanning-tree tagged-bpdu-vidspbmspbm ethertypespbm (ISIS Router Configuration)spbm lsdb-trap enablespbm nick-namespeed (Ethernet Interface Configuration)speed (Mgmt Interface Configuration)spf-delaysshcssh (Global Configuration)ssh (User Exec Configuration)sslstack auto-unit-replacement configstack auto-unit-replacement enablestack auto-unit-replacement-image enablestack auto-unit-replacement remove-mac-addressstack forced-modestack-monitorstack reboot-on-failurestack replacestack retry-countstorm-control unicast (Ethernet Interface Configuration)storm-control unicast (Global Configuration)sys-namesystem-id




Avaya.com/support


Commands starting with T


Commands starting with T organized alphabetically


tacacs accountingtacacs authorizationtacacs server hosttacacs server secondary-hosttacacs switchtelnettelnet-accessterminaltftp-servertimers basictimers basic holddowntoggle-next-boot-imagetracetraceroute




Avaya.com/support


Commands starting with U


Commands starting with U organized alphabetically


usb-host-portusernameusername addusername lockout-timeusername passwordusername WORD




Avaya.com/support


Commands starting with V


Commands starting with V organized alphabetically


vlacp enablevlacp (Ethernet Interface Configuration)vlacp hold_timevlacp macaddressvlan configcontrolvlan createvlan deletevlan igmpvlan igmp unknown-mcast-allow-floodvlan igmp unknown-mcast-no-floodvlan i-sidvlan membersvlan mgmtvlan namevlan portsvlan remote-span




Avaya.com/support


Commands starting with W


Commands starting with W organized alphabetically


web-serverwrite memory




Avaya.com/support


Application Configuration



S

slamon agent-comm-portslamon agent ip addressslamon agent portslamon clislamon cli-timeoutslamon cli-timeout-modeslamon ntrslamon oper-modeslamon refuse-server-testsslamon RTPslamon server-bypassslamon server ip addressslamon server port



Avaya.com/support


Ethernet Interface Configuration



A

auto-negotiation-advertisements

B

brouter

C

clear ipv6 destinationcache (Ethernet Interface Configuration)clear-stats

D

ddi-logging

F

flowcontrol

I

ip arp-inspection (Ethernet Interface Configuration)ip dhcp-relay (Ethernet Interface Configuration)ip dhcp-snooping (Ethernet Interface Configuration)ip igmp filterip ipfix (Ethernet Interface Configuration)ip ospf advertise-when-down enable (Ethernet Interface Configuration)ip ospf area (Ethernet Interface Configuration)ip ospf authentication-key (Ethernet Interface Configuration)ip ospf authentication-type (Ethernet Interface Configuration)ip ospf cost (Ethernet Interface Configuration)ip ospf dead-interval (Ethernet Interface Configuration)ip ospf enable (Ethernet Interface Configuration)ip ospf hello-interval (Ethernet Interface Configuration)ip ospf message-digest-key (Ethernet Interface Configuration)ip ospf mtu-ignore enable (Ethernet Interface Configuration)ip ospf network (Ethernet Interface Configuration)ip ospf primary-md5-key (Ethernet Interface Configuration)ip ospf priority (Ethernet Interface Configuration)ip ospf retransmit-interval (Ethernet Interface Configuration)ip ospf transit-delay (Ethernet Interface Configuration)ip rip advertise-when-down enable (Ethernet Interface Configuration)ip rip auto-aggregation enable (Ethernet Interface Configuration)ip rip cost (Ethernet Interface Configuration)ip rip default-listen enable (Ethernet Interface Configuration)ip rip default-supply enable (Ethernet Interface Configuration)ip rip enable (Ethernet Interface Configuration)ip rip holddown (Ethernet Interface Configuration)ip rip in-policy (Ethernet Interface Configuration)ip rip listen enable (Ethernet Interface Configuration)

ip rip out-policy (Ethernet Interface Configuration)ip rip poison enable (Ethernet Interface Configuration)ip rip proxy-announce enable (Ethernet Interface Configuration)ip rip receive (Ethernet Interface Configuration)ip rip send (Ethernet Interface Configuration)ip rip supply enable (Ethernet Interface Configuration)ip rip timeout (Ethernet Interface Configuration)ip rip triggered enable (Ethernet Interface Configuration)ip verify sourceisis (Ethernet Interface Configuration)isis hello-auth (Ethernet Interface Configuration)isis l1-dr-priority (Ethernet Interface Configuration)isis l1-hello-interval (Ethernet Interface Configuration)isis l1-hello-multiplier (Ethernet Interface Configuration)isis spbm (Ethernet Interface Configuration)

L

lacp aggregationlacp clear-statslacp key (Ethernet Interface Configuration)lacp modelacp prioritylacp timeout-timelldp config-notificationlldp location-identificationlldp med-network-policieslldp statuslldp tx-tlvlldp vendor-specific (Ethernet Interface Configuration)

M

mac-security (Ethernet Interface Configuration)

N

name

Q

qos if-assign (Ethernet Interface Configuration)qos if-queue-shaperqos if-shaper

R

rate-limit

S

sflow (Ethernet Interface Configuration)shutdown (Ethernet Interface Configuration)slpp (Ethernet Interface Configuration)slpp-guard (Ethernet Interface Configuration)smlt (Ethernet Interface Configuration)snmp trapspanning-tree bpdu-filtering (Ethernet Interface Configuration)spanning-tree (Ethernet Interface Configuration)speed (Ethernet Interface Configuration)storm-control unicast (Ethernet Interface Configuration)

V

vlacp (Ethernet Interface Configuration)



Avaya.com/support


Global Configuration



A

applicationarpasset-idaudit log saveauto-pvidautosave enableautotopology

B

banner

C

cfm spbm enablecfm spbm level <0-7>cfm spbm mepid <1-8191>cliclock sourceclock summer-timeclock sync-rtc-with-ntp enableclock time-zone

D

diagnostics-quick-mode enable

E

edmend

F

fafa authentication-keyfa extended-loggingfa message-authenticationfa port-enablefa proxyfa standalone-proxyfa timeoutfa uplinkfa vlanfa zero-touchfa zero-touch-optionsfcoe controllerfcoe controller-accessfcoe oper-modefcoe profile

H

http-porthttps-onlyhttps-port

I

interface Ethernetinterface loopbackinterface mgmtinterface mltinterface vlanip address (Global Configuration)ip arp-inspection (Global Configuration)ip blocking-modeip bootpip default-gatewayip dhcp client leaseip dhcp-relay (Global Configuration)ip dhcp-snooping bindingip dhcp-snooping external-saveip dhcp-snooping (Global Configuration)ip directed-broadcast enableip domain-nameip forward-protocol udp (Global Configuration)ip fwd-nh (Global Configuration)ip igmp fluship igmp profileip ipfix collectorip ipfix enableip ipfix (Global Configuration)ip ipfix slotip mgmt addressip mgmt default-gatewayip mgmt limitip mgmt netmaskip mgmt routeip mgmt shutdownip mgmt shutdown-intervalipmgrip name-serverip prefix-listip routeip routing (Global Configuration)ip source-interfaceipv6ipv6 addressipv6 autoconfigipv6 default-gatewayipv6 dhcp-relay (Global Configuration)ipv6 icmp addr-unreachipv6 icmp block-multicast-repliesipv6 icmp error-intervalipv6 icmp error-quotaipv6 icmp port-unreachipv6 icmp unreach-msgipv6 mgmt addressipv6 mgmt default-gatewayipv6 mgmt interfaceipv6 neighboripv6 routeipv6 tunneli-sid

J

jumbo-frames

L

lacp key (Global Configuration)lacp port-modelacp smlt-sys-idlacp system-prioritylink-state grouplldp med-fast-startlldp notification-intervallldp reinit-delaylldp tx-delaylldp tx-hold-multiplierlldp tx-intervallldp vendor-specific avaya call-serverlldp vendor-specific avaya file-serverlogginglogging remote

M

mac-address-tablemac-security auto-learningmac-security disablemac-security enablemac-security filteringmac-security intrusion-detectmac-security intrusion-timermac-security learningmac-security learning-portsmac-security mac-address-tablemac-security mac-da-filtermac-security security-listmac-security snmp-lockmaximum-pathmda enablemltmlt shutdown-ports-on-disable enablemlt spanning-tree

N

ntpntp server

O

ospf maximum-path

P

passwordport-mirroring

Q

qos actionqos agentqos classifierqos classifier-blockqos clear-statsqos egressmapqos if-action-extension

qos if-assign (Global Configuration)qos if-groupqos ingressmapqos ip-elementqos l2-elementqos meterqos policyqos queue-set-assignmentqos system-elementqos traffic-profile classifierqos traffic-profile setquickconfig enable

R

radius accounting enableradius reachabilityradius-serverradius use-management-iprear-port moderenumber unitrip maximum-pathrmon alarmrmon eventrmon historyrmon statsroute-maprouter isisrouter ospfrouter riprouter vrrp

S

serial-consoleserial-security enablesflowsflow collectorsftp-serverslpp (Global Configuration)slpp-guard (Global Configuration)snmp-server bootstrapsnmp-server communitysnmp-server contactsnmp-server disablesnmp-server enablesnmp-server hostsnmp-server locationsnmp-server namesnmp-server notification-controlsnmp-server notify-filtersnmp-server usersnmp-server viewsntp enablesntp serversntp sync-intervalsntp sync-nowspanning-tree 802dot1d-port-compliance enablespanning-tree add-vlanspanning-tree bpdu-filtering ignore-self (Global Configuration)spanning-tree cost-calc-modespanning-tree forward-timespanning-tree hello-timespanning-tree max-agespanning-tree mode

spanning-tree multicast-addressspanning-tree port-modespanning-tree priorityspanning-tree remove-vlanspanning-tree stpspanning-tree tagged-bpduspanning-tree tagged-bpdu-vidspbmspbm ethertypesshcssh (Global Configuration)sslstack auto-unit-replacement enablestack auto-unit-replacement-image enablestack forced-modestack-monitorstack reboot-on-failurestack replacestack retry-countstorm-control unicast (Global Configuration)

T

tacacs accountingtacacs authorizationtacacs server hosttacacs server secondary-hosttacacs switchtelnet-accesstftp-server

U

usb-host-portusernameusername addusername lockout-timeusername passwordusername WORD

V

vlacp enablevlacp hold_timevlacp macaddressvlan configcontrolvlan createvlan deletevlan igmpvlan igmp unknown-mcast-allow-floodvlan igmp unknown-mcast-no-floodvlan i-sidvlan membersvlan mgmtvlan namevlan portsvlan remote-span

W

web-server



Avaya.com/support


IGMP Filter Profile Configuration mode



R

range



Avaya.com/support


ISIS Router Configuration



C

csnp-interval

I

is-type

M

manual-areamax-lsp-gen-intervalmetric

O

overloadoverload-on-startup

P

psnp-interval

R

retransmit-lsp-interval

S

spbm (ISIS Router Configuration)spbm lsdb-trap enablespbm nick-namespf-delaysys-namesystem-id



Avaya.com/support


Loopback Interface Configuration



I

ip (Loopback Interface Configuration)ipv6 interface (Loopback Interface Configuration)



Avaya.com/support


Mgmt Interface Configuration



D

duplex

S

speed (Mgmt Interface Configuration)



Avaya.com/support


MLT Interface Configuration



I

ist

S

smlt (MLT Interface Configuration)



Avaya.com/support


OSPF Router Configuration



A

accept adv-rtrareaarea <A.B.C.D> rangearea virtual-linkarea virtual-link message-digest-keyas-boundary-routerauto-vlink

D

default-cost

H

host-route

N

network (OSPF Router Configuration)

R

redistributerfc1583-compatibilityrouter-id

T

timers basic holddown



Avaya.com/support


Privileged EXEC


Privileged EXEC

A

audit log noerase enable

B

blink-ledsboot

C

clear arp-cacheclear audit logclear ip-blockingclear ip dhcp-snoopingclear ip forward-protocolclear ip igmpclear ip ospfclear ipv6clear ipv6 dhcp-relayclear ipv6 neighbor-cacheclear isis lsdbclear isis statsclear loggingclear mac-address-tableclear sshcclear stack port-statisticsclear system last-exceptionclockconfigurecopy configcopy nvramcopy running-configcopy sftpcopy tftpcopy usb

D

disabledownload

I

installip dhcp-snooping external-save restoreip ipfix flush portip ospf apply acceptip ospf apply redistribute

M

manualtrigger ip rip interface vlan

Q

quickconfig start-recording

R

reloadrenewrestore factory-default

S

save configscript runscript uploadshow audit logshow auto-negotiation-advertisementsshow auto-negotiation-capabilitiesshow autosaveshow autotopologyshow bannershow clishow clockshow config-networkshow diagnostics-quick-modeshow ip igmpshow ip igmp cacheshow ip igmp groupshow ip igmp group-extshow ip igmp interfaceshow ip igmp profileshow ip igmp router-alertshow ip igmp snoopingshow ip igmp snoop-querier-addrshow ipmgrshow jumbo-framesshow lacp aggrshow lacp debugshow lacp keyshow lacp portshow lacp port-modeshow lacp statsshow lacp systemshow loggingshow mac-address-tableshow mac-address-table addressshow mac-address-table aging-timeshow mac-address-table dynamicshow mac-address-table mltshow mac-address-table portshow mac-address-table spbmshow mac-address-table staticshow mac-address-table vidshow mac-securityshow mltshow mlt hash-calcshow port-mirroringshow port-statisticsshow qos actionshow qos agentshow qos capabilityshow qos classifiershow qos classifier-blockshow qos diag

show qos egressmapshow qos if-action-extensionshow qos if-assignshow qos if-groupshow qos if-queue-shapershow qos if-shapershow qos ingressmapshow qos ip-elementshow qos l2-elementshow qos metershow qos policyshow qos portshow qos queue-setshow qos queue-set-assignmentshow qos statisticsshow qos system-elementshow qos traffic-profileshow radius-servershow rate-limitshow rmon alarmshow rmon ethernetshow rmon eventshow rmon historyshow rmon statsshow running-configshow scriptshow serial-consoleshow sflowshow sflow collectorshow sflow interfaceshow slppshow snmp-servershow sntpshow sshshow sslshow stack-infoshow stack-monitorshow storm-controlshow sys-infoshow systemshow tacacsshow telnet-accessshow telnet sessionsshow tftp-servershow traceshow usb-filesshow usb-host-portshow vlacpshow vlanshow web-servershutdown (Privileged EXEC)stack auto-unit-replacement configstack auto-unit-replacement remove-mac-address

T

toggle-next-boot-imagetrace

W

write memory


Version 04.01 July 2015

Privileged Executive



C

clear ipv6 destinationcache

S

show fashow fa agentshow fa elementshow fa i-sidshow fa port-enableshow fa uplinkshow fa vlanshow fa zero-touch-optionsshow ipv6 default-routers (Privileged Executive)show ipv6 destinationcache (Privileged Executive)show ipv6 mld-host-cache (Privileged Executive)show vlan configcontrolshow vlan dhcp-relayshow vlan idshow vlan igmpshow vlan interfaceshow vlan ipshow vlan i-sidshow vlan mgmtshow vlan multicastshow vlan remote-spanshow vlan summaryshow vlan typeshow vlan voice-vlan



Avaya.com/support


RIP Router Configuration



D

default-metric

N

network (RIP Router Configuration)

T

timers basic



Avaya.com/support


User EXEC


User EXEC

E

enableexit

H

help

L

l2 pingl2 traceroutel2 tracetreelogout

P

ping

R

run spbm

S

show application slamon agentshow arpshow arp-tableshow auto-pvidshow bootshow broutershow cfm spbmshow cpu-utilizationshow ddi-loggingshow ecmpshow edm help-file-pathshow environmentalshow fcoeshow flashshow http-portshow https-onlyshow https-portshow interfacesshow interfaces admin-disabledshow interfaces admin-enabledshow interfaces gbic-infoshow interfaces link-downshow interfaces link-upshow interfaces loopbackshow interfaces namesshow interfaces names

show interfaces <port>show interfaces verboseshow ipshow ip addressshow ip arp-inspectionshow ip arp-proxyshow ip-blockingshow ip blocking-modeshow ip bootpshow ip default-gatewayshow ip default-ttlshow ip dhcp client leaseshow ip dhcp-relayshow ip dhcp-snooping bindingshow ip dhcp-snooping external-saveshow ip dhcp-snooping interfaceshow ip dhcp-snooping vlanshow ip directed-broadcastshow ip dnsshow ip forward-protocolshow ip ipfixshow ip ipfix collectorshow ip ipfix interfaceshow ip ipfix slotshow ip ipfix tableshow ip mgmtshow ip netstatshow ip ospfshow ip ospf acceptshow ip ospf areashow ip ospf area-rangeshow ip ospf aseshow ip ospf authenticationshow ip ospf default-costshow ip ospf host-routeshow ip ospf ifstatsshow ip ospf int-authshow ip ospf interfaceshow ip ospf int-timersshow ip ospf lsdbshow ip ospf neighborshow ip ospf redistributeshow ip ospf statsshow ip ospf timershow ip ospf virtual-linkshow ip ospf virtual-neighborsshow ip prefix-listshow ip ripshow ip routeshow ip routingshow ip source-interfaceshow ipv6 addressshow ipv6 default-gatewayshow ipv6 dhcp-relayshow ipv6 globalshow ipv6 interfaceshow ipv6 mgmtshow ipv6 ndshow ipv6 nd-prefixshow ipv6 neighborshow ipv6 routeshow ipv6 tcpshow ipv6 tunnelshow ipv6 udpshow ip vrrp

show ip vrrp addressshow ip vrrp interfaceshow i-sidshow isis adjacenciesshow isis int-authshow isis int-ckt-levelshow isis int-countersshow isis interfaceshow isis int-l1-cntl-pktsshow isis int-timersshow isis lsdbshow isis manual-areashow isis netshow isis spbm i-sidshow isis spbm multicast-fibshow isis spbm nick-nameshow isis spbm unicast-fibshow isis spbm unicast-treeshow isis statisticsshow isis system-idshow istshow link-stateshow lldpshow lldp local-sys-datashow lldp med-network-policiesshow lldp mgmt-sys-datashow lldp neighborshow lldp neighbor-mgmt-addrshow lldp pdu-tlv-sizeshow lldp portshow lldp rx-statsshow lldp statsshow lldp tx-statsshow lldp tx-tlvshow lldp vendor-specific avayashow mdashow memory-utilizationshow mgmt-port statusshow ntpshow nvram blockshow passwordshow quickconfigshow radiusshow rear-portshow roleshow route-mapshow serial-securityshow sftp-servershow slpp-guardshow smltshow spanning-treeshow spbmshow sshcshow stack auto-unit-replacementshow stack auto-unit-replacement-imageshow stack-cable-infoshow stack forced-modeshow stack healthshow stack reboot-on-failureshow stack retry-countshow techshow terminalshow usernameshow whossh (User Exec Configuration)

T

telnetterminaltraceroute



Avaya.com/support


User Executive


User Executive

S

show ipv6 default-routers (User Executive)show ipv6 destinationcache (User Executive)show ipv6 mld-host-cache



Avaya.com/support


VLAN Interface Configuration



I

ip address (VLAN Interface Configuration)ip arp-proxyip dhcp-relay (VLAN Interface Configuration)ip directed-broadcast (VLAN Interface Configuration)ip forward-protocol udp (VLAN Interface Configuration)ip fwd-nh (VLAN Interface Configuration)ip igmpip igmp last-member-query-intervalip igmp mrouterip igmp proxyip igmp query-intervalip igmp query-max-responseip igmp robust-valueip igmp router-alertip igmp send-queryip igmp snoopingip igmp versionip ospf advertise-when-down enable (VLAN Interface Configuration)ip ospf area (VLAN Interface Configuration)ip ospf authentication-key (VLAN Interface Configuration)ip ospf authentication-type (VLAN Interface Configuration)ip ospf cost (VLAN Interface Configuration)ip ospf dead-interval (VLAN Interface Configuration)ip ospf enable (VLAN Interface Configuration)ip ospf hello-interval (VLAN Interface Configuration)ip ospf message-digest-key (VLAN Interface Configuration)ip ospf mtu-ignore enable (VLAN Interface Configuration)ip ospf network (VLAN Interface Configuration)ip ospf primary-md5-key (VLAN Interface Configuration)ip ospf priority (VLAN Interface Configuration)ip ospf retransmit-interval (VLAN Interface Configuration)ip ospf transit-delay (VLAN Interface Configuration)ip rip advertise-when-down enable (VLAN Interface Configuration)ip rip auto-aggregation enable (VLAN Interface Configuration)ip rip cost (VLAN Interface Configuration)ip rip default-listen enable (VLAN Interface Configuration)ip rip default-supply enable (VLAN Interface Configuration)ip rip enable (VLAN Interface Configuration)ip rip holddown (VLAN Interface Configuration)ip rip in-policy (VLAN Interface Configuration)ip rip listen enable (VLAN Interface Configuration)ip rip out-policy (VLAN Interface Configuration)ip rip poison enable (VLAN Interface Configuration)ip rip proxy-announce enable (VLAN Interface Configuration)ip rip receive (VLAN Interface Configuration)ip rip send (VLAN Interface Configuration)ip rip supply enable (VLAN Interface Configuration)ip rip timeout (VLAN Interface Configuration)ip rip triggered enable (VLAN Interface Configuration)

ip routing (VLAN Interface Configuration)ipv6 dhcp-relay (VLAN Interface Configuration)ipv6 interface (VLAN Interface Configuration)ipv6 nd prefixipv6 nd prefix-interfaceipv6 nd (VLAN Interface Configuration)ip vrrpip vrrp address



Avaya.com/support


VRRP Router Configuration



P

ping-virtual-address



Avaya.com/support


Command: accept adv-rtr


accept adv-rtr

Configures the OSPF accept-advertisements router policy.

Syntax

accept adv-rtr <A.B.C.D>

accept adv-rtr <A.B.C.D> enable

accept adv-rtr <A.B.C.D> metric-type {any | type1 | type2}

accept adv-rtr <A.B.C.D> route-policy <WORD>

default accept adv-rtr <A.B.C.D>

default accept adv-rtr <A.B.C.D> enable

default accept adv-rtr <A.B.C.D> metric-type

default accept adv-rtr <A.B.C.D> route-policy

no accept adv-rtr <A.B.C.D>

no accept adv-rtr <A.B.C.D> enable

Default

None

Command mode


Command parameters

Parameter Description

A.B.C.DRepresents the IP address of the router from which advertisements are to beaccepted. The value 0.0.0.0 denotes that advertisements from all routers areaccepted

any match any metric typeenable Enables the accept entry for the router specified in the <ip_address> parametermetric-type{any | type1| type2}

Indicates the type of OSPF external routes that will be accepted from this router

route-policy<WORD>

Specifies the name of a previously configured route map to be used for filteringexternal routes advertised by the specified advertising router before acceptingthem into the routing table

type1 match type-1 metric typetype2 match type-2 metric type



Avaya.com/support


Command: application


application

Use this command to enter Application Configuration mode.

Syntax

application

Default

None

Command mode




Avaya.com/support


Command: area


area

Configures area.

Syntax

area {A.B.C.D}

area {A.B.C.D} default-cost <0-16777215>

area {A.B.C.D} import external

area {A.B.C.D} import noexternal

area {A.B.C.D} import nssa

area {A.B.C.D} import-summaries enable

default area {A.B.C.D} default-cost

default area {A.B.C.D} import

default area {A.B.C.D} import-summaries enable

no area {A.B.C.D} import-summaries enable

Default

None

Command mode


Command parameters

Parameter DescriptionA.B.C.D Specifies the Area ID in dotted decimal notation (A.B.C.D)default-cost{0-16777215}

Specifies the default cost associated with an OSPF stub area

external Specifies a normal areaimport{external |noexternal |nssa}

Specifies the area type by defining the area's support for importing AutonomousSystem external link state advertisements: external: specifies a normal area;noexternal: specifies a stub area ; nssa: specifies an NSSA.

import-summaries Controls the import of summary link state advertisements into stub areas. This

setting has no effect on other areas.

{enable}

noexternal Specifies a stub areanssa Specifies a not-so-stubby area



Avaya.com/support


Command: area <A.B.C.D> range


area <A.B.C.D> range

Configures the area range.

Syntax

area {A.B.C.D} range <A.B.C.D/<0-32> nssa-extlink advertise-metric <0-65535>

area {A.B.C.D} range <A.B.C.D/<0-32> nssa-extlink advertise-mode <no-

summarize|summarize|suppress>

area {A.B.C.D} range <A.B.C.D/<0-32> summary-link advertise-metric <0-65535>

area {A.B.C.D} range <A.B.C.D/<0-32> summary-link advertise-mode <no-

summarize|summarize|suppress>

default area {A.B.C.D} range <A.B.C.D/<0-32> nssa-extlink advertise-metric

default area {A.B.C.D} range <A.B.C.D/<0-32> nssa-extlink advertise-mode

default area {A.B.C.D} range <A.B.C.D/<0-32> summary-link advertise-metric

default area {A.B.C.D} range <A.B.C.D/<0-32> summary-link advertise-mode

no area {A.B.C.D} range <A.B.C.D/<0-32> nssa-extlink

no area {A.B.C.D} range <A.B.C.D/<0-32> summary-link

Default

None

Command mode


Command parameters

Parameter Description<A.B.C.D/<0-32> Specifies the IP address and mask.

A.B.C.D Specifies the Area ID in dotted decimalnotation (A.B.C.D)

advertise-metric <0-65535> Configure metric to be advertised for arearange

advertise-mode {no-summarize | summarize| suppress}

Select advertise mode for area range

nssa-extlink Not-so-stubby area link summary (Type 7)summary-link Aggregated summary (Type 3)



Avaya.com/support


Command: area virtual-link


area virtual-link

Creates a virtual link.

Syntax

area virtual-link {A.B.C.D} {A.B.C.D}

area virtual-link {A.B.C.D} <nghbr-routerid> authentication-key WORD

area virtual-link {A.B.C.D} <nghbr-routerid> authentication-type message-digest

area virtual-link {A.B.C.D} <nghbr-routerid> authentication-type none

area virtual-link {A.B.C.D} <nghbr-routerid> authentication-type simple

area virtual-link {A.B.C.D} <nghbr-routerid> dead-interval <0-2147483647>

area virtual-link {A.B.C.D} <nghbr-routerid> hello-interval <1-65535>

area virtual-link {A.B.C.D} <nghbr-routerid> primary-md5-key <1-255>

area virtual-link {A.B.C.D} <nghbr-routerid> retransmit-interval <0-3600>

area virtual-link {A.B.C.D} <nghbr-routerid> transit-delay <0-3600>

default area virtual-link {A.B.C.D} <nghbr-routerid>

default area virtual-link {A.B.C.D} <nghbr-routerid> authentication-type

default area virtual-link {A.B.C.D} <nghbr-routerid> dead-interval

default area virtual-link {A.B.C.D} <nghbr-routerid> hello-interval

default area virtual-link {A.B.C.D} <nghbr-routerid> primary-md5-key

default area virtual-link {A.B.C.D} <nghbr-routerid> retransmit-interval

default area virtual-link {A.B.C.D} <nghbr-routerid> transit-delay

no area virtual-link {A.B.C.D} <nghbr-routerid>

Default

None

Command mode


Command parameters

Parameter Description{A.B.C.D} Specifies the transit area ID in dotted decimal notation (A.B.C.D)<nghbr-routerid> Specifies the neighbor router ID in dotted decimal notation (A.B.C.D)authentication-key <WORD>

Specifies the unique identifier assigned to the authentication key

authentication-type {message-digest | none |simple}

Specifies one of the following authentication types: message-digest (MD5),none, simple (simple password authentication type)

dead-interval<1-2147483647>

Specifies the time interval, in seconds, that a Hello packet has not beentransmitted from the virtual interface before its neighbors declare it down.Expressed as an integer from 1-2147483647, the default dead interval value is60 seconds

hello-interval<1-65535>

Specifies the time interval, in seconds, between transmission of Hello packetsfrom the virtual interface. Expressed as an integer from 1-65535, the hello-interval default value is 10 seconds

primary-md5-key<1-255>

Specifies the user-selected key used to encrypt OSPF protocol packets fortransmission.

retransmit-interval <1-3600>

Specifies the time interval, in seconds, between link stage advertisementretransmissions for adjacencies belonging to the virtual interface. Expressed asan integer from 1-3600, the default value is 5 seconds.

transit-delay<1-3600>

Specifies the estimated number of seconds required to transmit a link stateupdate packet over the virtual interface. Expressed as an integer from 1-3600,the default value is 1 second.



Avaya.com/support


Command: area virtual-link message-digest-key


area virtual-link message-digest-key

Creates a virtual interface message digest key.

Syntax

area virtual-link message-digest-key {A.B.C.D} <neighbor_id> <1-255> md5-key <WORD>

default area virtual-link message-digest-key {A.B.C.D} <neighbor_id> <1-255>

no area virtual-link message-digest-key {A.B.C.D} <neighbor_id> <1-255>

Default

None

Command mode


Command parameters

Parameter Description{A.B.C.D} Specifies the transit area Id expressed as an IP address<1-255> Specifies the primary MD5 key value, expressed as an integer from 1-255.<neighbor_id> Specifies the neighbor router ID expressed as an IP addressmd5-key<WORD>

Specifies the user-selected key used to encrypt OSPF protocol packets fortransmission.



Avaya.com/support


Command: arp


arp

Configures a static ARP entry.

Syntax

arp <A.B.C.D> <H.H.H> <WORD> id <1-4094>

arp timeout <5-360>

default arp timeout

no arp <A.B.C.D>

Default

None

Command mode


Command parameters

Parameter Description<A.B.C.D> Specifies the IP address of the ARP entry.

<H.H.H> Specifies the MAC address of the ARP entry (i.e. H.H.H or xx:xx:xx:xx:xx:xx orxx.xx.xx.xx.xx.xx or xx-xx-xx-xx-xx-xx).

<WORD> Specifies the unit/port.id <1-4094>

Specifies the VLAN ID.

timeout<5-360>

Specifies the time for the entry to exist.



Avaya.com/support


Command: as-boundary-router


as-boundary-router

Configures a router as an ASBR.

Syntax

as-boundary-router enable

default as-boundary-router

default as-boundary-router enable

no as-boundary-router

no as-boundary-router enable

Default

Disabled

Command mode


Command parameters

Parameter Descriptionenable Configure switch as ASBR



Avaya.com/support


Command: asset-id


asset-id

Configures the asset ID.

Syntax

asset-id <WORD>

asset-id stack <WORD>

asset-id unit <1-8> <WORD>

default asset-id

default asset-id stack

default asset-id unit <1-8>

no asset-id

no asset-id stack

no asset-id unit <1-8>

Default

None

Command mode


Command parameters

Parameter Description<WORD> Specifies the asset-ID of this unit.stack <WORD> Specifies the asset-ID for the stack.unit <1-8> Specifies the asset-ID for specific unit in the stack.



Avaya.com/support


Command: audit log noerase enable



Prevents erasure of the ACLI audit log. Applying the audit log noerase enable command on a switch is a one time function, whichis irreversible and is only applicable when the switch is running the standard software image. After the no-erase audit log flag isset, you cannot clear the audit log, even if the switch is re-configured to factory defaults.

Syntax


Default

Disabled

Command mode

Privileged EXEC



Avaya.com/support


Command: audit log save


audit log save

Enables audit log save settings.

Syntax

audit log save

default audit log

no audit log

Default

Enabled

Command mode




Avaya.com/support


Command: auto-negotiation-advertisements


auto-negotiation-advertisements

Configures auto-negotiation advertisement settings.

Syntax

[default] [no] auto-negotiation-advertisements port <ports>

auto-negotiation-advertisements 10000-full [asymm-pause-frame | pause-frame]

auto-negotiation-advertisements 1000-full [10000-full] [40000-full] [asymm-pause-frame |

pause-frame]

auto-negotiation-advertisements 100-full [1000-full] [10000-full] [40000-full] [asymm-

pause-frame | pause-frame]

auto-negotiation-advertisements asymm-pause-frame

auto-negotiation-advertisements none

auto-negotiation-advertisements pause-frame [asymm-pause-frame]

Default

None

Command mode


Command parameters

Parameter Description10000-full Advertise 10000 Mbps full-duplex1000-full Advertise 1000 Mbps full-duplex100-full Advertise 100 Mbps full-duplex40000-full Advertise 40000 Mbps full-duplexasymm-pause-frame Advertise use of asymmetric pause frames half-duplexnone Do not advertise during auto-negotiation.pause-frame Advertise use of pause frames.port <port> Select port for operation.



Avaya.com/support


Command: auto-pvid


auto-pvid

Enables auto-PVID for all ports.

Syntax

auto-pvid

no auto-pvid

Default

Enabled

Command mode




Avaya.com/support


Command: autosave enable


autosave enable

Enables autosave settings.

Syntax

autosave enable

default autosave enable

no autosave enable

Default

Enabled

Command mode




Avaya.com/support


Command: autotopology


autotopology

Enables the autotopology protocol.

Syntax

autotopology

default autotopology

no autotopology

Default

Enabled

Command mode




Avaya.com/support


Command: auto-vlink


auto-vlink

Enables global automatic Virtual Link creation.

Syntax

auto-vlink

default auto-vlink

no auto-vlink

Default

None

Command mode




Avaya.com/support


Command: banner


banner

Configure the ACLI logon banner to display a warning message to users before authentication.

Syntax

banner <1-19> <text>

banner custom

banner disabled

banner static

no banner

Default

Static

Command mode


Command parameters

Parameter Description<1-19> Specifies the line number in the custom banner.<text> Adds lines of text to the ACLI logon banner.custom Activates the custom banner.disabled Skips the banner display.static Activates static banner.



Avaya.com/support


Command: blink-leds


blink-leds

Blinks the LEDs on the display panel to identify the unit.

Syntax

blink-leds

blink-leds off

blink-leds time <1-10>

blink-leds unit <1-8>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionoff Stops blinking the LEDs.time <1-10> Specifies how long to blink the LEDs.unit <1-8> Specifies the unit number.



Avaya.com/support


Command: boot


boot

Resets the stack or switch.

Syntax

boot

boot default [unit <1-8>]

boot partial-default

boot primary

boot secondary

boot unit <1-8>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptiondefault Reboot the stack or switch and use the factory default configuration.partial-default Reboot the stack or switch and use partial factory default configuration.primary Reboot the stack or switch and use the primary agent image.secondary Reboot the stack or switch and use the secondary agent image.unit <1-8> Specifies the unit number.



Avaya.com/support


Command: brouter


brouter

Configures brouter ports.

Syntax

[no] brouter port <port> routing enable

brouter port <port> subnet <A.B.C.D.0-32> [routing enable]

brouter port <port> vlan <1-4094> [subnet <A.B.C.D.0-32>] [routing enable]

Default

None

Command mode


Command parameters

Parameter Descriptionport <port> Specifies the port to configure as a brouter port.routingenable

Enables Layer 3 routing on the brouter port.

subnetA.B.C.D/<0-32>

Specifies the IP address and subnet mask of the brouter. When creating a newbrouter, this is the IP address and subnet mask assigned.

vlan <1-4094>

Specifies the VLAN ID of the brouter. When creating a new brouter port, this is theVLAN ID assigned to the brouter port.



Avaya.com/support


Command: cfm spbm enable


cfm spbm enable

Enables CFM.

Syntax

cfm spbm enable

no cfm spbm enable

Default

Disabled

Command mode




Avaya.com/support


Command: cfm spbm level <0-7>


cfm spbm level <0-7>

Configures the maintenance domain level.

Syntax

cfm spbm level <0-7>

default cfm spbm level

Default

4

Command mode




Avaya.com/support


Command: cfm spbm mepid <1-8191>


cfm spbm mepid <1-8191>

Assigns a global MEP ID for all CFM SPBM MEPs.

Syntax

cfm spbm mepid <1-8191>

default cfm spbm mepid

Default

1

Command mode




Avaya.com/support


Command: clear arp-cache


clear arp-cache

Clears the Layer 3 ARP cache.

Syntax

clear arp-cache

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: clear audit log


clear audit log

Clears audit log.

Syntax

clear audit log

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: clear ip-blocking


clear ip-blocking

Clears the Layer 3 IP blocking state.

Syntax

clear ip-blocking

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: clear ip dhcp-snooping


clear ip dhcp-snooping

Clears DHCP snooping data.

Syntax

clear ip dhcp-snooping binding

clear ip dhcp-snooping binding {dynamic | static}

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionbinding Clears DHCP snooping bindings.dynamic Clears DHCP snooping dynamic bindings.static Clears DHCP snooping static bindings.



Avaya.com/support


Command: clear ip forward-protocol


clear ip forward-protocol

Clears broadcast protocols counters.

Syntax

clear ip forward-protocol udp counters

clear ip forward-protocol udp counters <VLAN>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<VLAN> Clears counters for specific VLAN.udp counters Clears UDP broadcast counters.



Avaya.com/support


Command: clear ip igmp


clear ip igmp

Clears IGMP data.

Syntax

clear ip igmp profile stats

clear ip igmp profile stats <1-65535>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<1-65535> Clears a profile ID.profile stats Clears IGMP profile statistics data.



Avaya.com/support


Command: clear ip ospf


clear ip ospf

Clears OSPF-related data.

Syntax

clear ip ospf counters

clear ip ospf counters <1-4094>

Default

None

Command mode

Privileged EXEC

Command parameters


<1-4094> Specifies the VLAN ID. Range is 1-4094. If no VLAN is specified, the command clearsOSPF global counters.

counters Clears OSPF counters.



Avaya.com/support


Command: clear ipv6


clear ipv6

Clears IPv6 data.

Syntax

clear ipv6

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: clear ipv6 destinationcache



Clear the IPv6 destination cache.

Syntax


Default

None

Command mode




Avaya.com/support


Command: clear ipv6 destinationcache(Ethernet Interface Configuration)


clear ipv6 destinationcache (Ethernet Interface Configuration)

Clear the IPv6 destination cache.

Syntax


Default

None

Command mode




Avaya.com/support


Command: clear ipv6 dhcp-relay


clear ipv6 dhcp-relay

Clears IPv6 DHCP-relay data.

Syntax

clear ipv6 dhcp-relay counters

clear ipv6 dhcp-relay counters vlan <1-4094>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptioncounters Clears IPv6 DHCP-Relay counters.vlan <1-4094> Specifies the VLAN ID.



Avaya.com/support


Command: clear ipv6 neighbor-cache


clear ipv6 neighbor-cache

Clears the IPv6 neighbor cache.

Syntax

clear ipv6 neighbor-cache

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: clear isis lsdb


clear isis lsdb

Clears LSP database and restarts the state machine.

Syntax

clear isis lsdb

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: clear isis stats


clear isis stats

Clears ISIS statistics.

Syntax

clear isis stats

clear isis stats {error-counters | packet-counters}

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionerror-counters Clears ISIS error counters.packet-counters Clears ISIS packet counters.



Avaya.com/support


Command: clear logging


clear logging

Clears log messages (with no parameters, from DRAM only).

Syntax

clear logging

clear logging non-volatile [<critical | serious>]

clear logging nv

clear logging volatile [<critical | informational | serious>]

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptioncritical Clear critical log messages.informational Clear informational log messages.non-volatile Clear log messages from NVRAM.nv Clear log messages from NVRAM and DRAM.serious Clear serious log messages.volatile Clear log messages from DRAM.



Avaya.com/support


Command: clear mac-address-table


clear mac-address-table

Flushes the MAC address table for a specific VLAN.

Syntax

clear mac-address-table

clear mac-address-table address <H.H.H>

clear mac-address-table dynamic

clear mac-address-table interface {Ethernet <port> | mlt <1-64> | vlan <1-4094>}

clear mac-address-table static

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionaddress <H.H.H> Flush a single MAC Address.

dynamic Flush only dynamically learnedaddresses.

interface {Ethernet <port> | mlt <1-64> | vlan1-4094>}

Flush MAC Addresses of a specificinterface.

static Flush only statically insertedaddresses.



Avaya.com/support


Command: clear sshc


clear sshc

Clears SSH client parameters. This command is available only if the switch runs a secure image.

Syntax

clear sshc known-host {all | hostname | A.B.C.D | WORD>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionknown-host {all |hostname | A.B.C.D |WORD>

Clears SSH client known hosts by providing a hostname, IPv4, orIPv6 address. Optionally, you can clear all known hosts.



Avaya.com/support


Command: clear stack port-statistics


clear stack port-statistics

Clears the stack port counters.

Syntax

clear stack port-statistics

clear stack port-statistics unit <1-8>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionunit <1-8> Clears port statistics for a specific unit in a stack.



Avaya.com/support


Command: clear-stats


clear-stats

Clears the port counter.

Syntax

clear-stats

clear-stats port <ports>

clear-stats port mgmt

Default

None

Command mode


Command parameters

Parameter Descriptionport <mgmt> Clears management port statistics.port <port> Selects a port to clear the port counter.



Avaya.com/support


Command: clear system last-exception


clear system last-exception

Clears last software exception information.

Syntax

clear system last-exception

clear system last-exception unit <1-8>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionunit <1-8> Clears system parameters for a specific unit in a stack.



Avaya.com/support


Command: clock


clock

Configures the Real Time Clock.

Syntax

clock set <hh:mm:ss> <1-31> <month>

clock set <mmddyyyyhhmmss>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<1-31> Specifies the date.<hh:mm:ss> Specifies the hour, minutes, and seconds.<mmddyyyyhhmmss> Specfies the month, day, year, hour, minutes, and seconds.<month> Specifies the month.



Avaya.com/support


Command: clock source


clock source

Configures the time source.

Syntax

clock source {ntp | rtc | sntp | sysUpTime}

default clock source

Default

SNTP

Command mode


Command parameters

Parameter Descriptionntp Specifies Network Time Protocol (NTP) as the time source.rtc Specifies Real Time Clock (RTC) as the time source.sntp Specifies Simple Network Time Protocol (SNTP) as the time source.sysUpTime Specifies System Up Time as the time source.



Avaya.com/support


Command: clock summer-time


clock summer-time

Configures the system to automatically switch to summer time (daylight saving time).

Syntax

clock summer-time <WORD> date <1-31> <Month> <1999-2099> hh:mm <1-31> <Month> <1999-2099>

hh:mm [<-840 - 840>]

clock summer-time recurring <1-5 | Last > <Day> <Month> <hh:mm> <1-5 | Last > <Day> <Month>

<hh:mm> <1-1440>

default clock summer-time recurring

no clock summer-time

no clock summer-time recurring

Default

Disabled

Command mode


Command parameters

Parameter Description<1-1440> Specifies the umber of minutes to add or substract during summer-time recurring.<1-31> Specifies the day of the month when summer time starts or ends.<1-5> Specifies the week of the month when the summer-time recurring starts or ends.<1990-2099>

Specifies the year when summer time starts or ends.

<-840 -840>

Specifies the number of minutes to add or substract during summer time.

<WORD> Sets the time zone acronym containing at most 4 characters (for example 'PDT' forPacific Daylight Time) to be displayed when summer time is in effect.

date Indicates that summer time should start on the first specific date listed in the commandand end the second specific date in the command.

day Specifies the day of the week when summer-time recurring starts or ends, for example,Monday or Tuesday.

hh:mm Specifies the time in hours and minutes when summer-time recurring starts.last Selects the last day which will be specified of the month for summer-time starts or ends.

month Specifies the month when summer-time recurring starts or ends, for example, January orFebruary.

recurring Specifies the summer-time dates which recur every year.



Avaya.com/support


Command: clock sync-rtc-with-ntpenable


clock sync-rtc-with-ntp enable

Synchronize the RTC with SNTP or NTP status.

Syntax

clock sync-rtc-with-ntp enable

default clock sync-rtc-with-ntp enable

no clock sync-rtc-with-ntp enable

Default

No synchronization

Command mode




Avaya.com/support


Command: clock time-zone


clock time-zone

Configures the local time zone.

Syntax

clock time-zone <WORD> <-12 - 13>

clock time-zone <WORD> <-12 - 13> <0-59>

no clock time-zone

Default

None

Command mode


Command parameters

Parameter Description<0-59> Specifies the minutes difference from UTC (0, 15, 30 or 45).<-12 - 13> Spcecifies the hours difference from UTC.<WORD> Specifies the time zone acronym containing at most 4 characters.



Avaya.com/support


Command: configure


configure

Enter Global Configuration mode.

Syntax

configure

configure network

configure network address {A.B.C.D | <WORD>}

configure network address {A.B.C.D | <WORD>} filename <WORD>

configure network filename <WORD>

configure network filename <WORD> address {A.B.C.D | <WORD>}

configure network load-on-boot disable

configure network load-on-boot use-bootp

configure network load-on-boot use-config

configure terminal

configure usb filename <WORD>

configure usb filename <WORD> unit <1-8>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionaddress {A.B.C.D |<WORD>}

Specifies IPv4 or IPv6 address of TFTP server.

filename <WORD> Specifies the filename of configuration file.load-on-boot Specifies settings for loading config file at boot time.terminal Configures from the terminal.usb Configures from USB.use-bootp Loads the configuration file at boot time using BOOTP.

use-config Load the configuration file at boot time using configuredparameters.



Avaya.com/support


Command: copy config


copy config

Copies from the current configuration.

Syntax

copy config

copy config nvram

copy config nvram block <1-2> name <WORD>

copy config tftp address {A.B.C.D | <WORD>}

copy config tftp address {A.B.C.D | <WORD>} filename <WORD>

copy config usb filename <WORD>

copy config usb filename <WORD> unit <1-8>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionaddress {A.B.C.D | <WORD>} Specify the IPv4 or IPv6 address of the TFTP server.block <1-2> Specify configuration block number.filename <word> Specify the filename in which to store the configuration.name <WORD> Specify configuration block name.nvram Copies to local NV storage.tftp Copies to TFTP server.unit <1-8> Copy to the USB of another unit in a stack.usb Copies to USB.



Avaya.com/support


Command: copy nvram


copy nvram

Loads the configuration from the specified NV storage configuration block.

Syntax

copy nvram config block <1-2>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionblock <1-2> Specify configuration block number.



Avaya.com/support


Command: copy running-config


copy running-config

Copies from the current configuration as a series of ACLI commands.

Syntax

copy running-config tftp [verbose] address {A.B.C.D | <WORD>} filename <WORD>

copy running-config tftp [verbose] module <802.1ab | aaur | arp-inspection | asset-id| aur

|banner| brouter| cfm | core | default-cmd-interface |dhcp-relay | dhcp-snooping | fcoe

|igmp| interface| ip | ip-source-guard |ipfix | ipmgr | |ipv6 | l3 | l3-protocols | lacp |

link-state | logging | mac-security | mlt | port-qmirroring | qos | rate-limit | rmon |

rtc | slamon | slpp | smlt | snmp | spbm | stack | stkmon| stp| unicast-storm-control |

vlacp | vlan> [address {A.B.C.D | <WORD>}] [filename <WORD>]

copy running-config usb [verbose] filename <WORD>

copy running-config usb [verbose] filename <WORD> unit <1-8>

copy running-config usb [verbose] module <802.1ab | aaur | arp-inspection | asset-id| aur

|banner| brouter| cfm | core | default-cmd-interface |dhcp-relay | dhcp-snooping | fcoe

|igmp| interface| ip | ip-source-guard |ipfix | ipmgr | |ipv6 | l3 | l3-protocols | lacp |

link-state | logging | mac-security | mlt | port-qmirroring | qos | rate-limit | rmon |

rtc | slamon | slpp | smlt | snmp | spbm | stack | stkmon| stp| unicast-storm-control |

vlacp | vlan> [filename <WORD>}]

Default

None

Command mode

Privileged EXEC

Command parameters


address {A.B.C.D | <WORD>}

Specify theIPv4 or IPv6address ofthe TFTPserver.

filename <word>

Specify thefilename inwhich tostore theconfiguration.

module <802.1ab | aaur | arp-inspection | asset-id| aur |banner|

Command: copy sftp


copy sftp

Copies configuration from an SFTP server. You can only use this command if the switch runs a secure image.

Syntax

copy sftp config address {A.B.C.D | <WORD>} filename <WORD> unit <1-8 | all> username

<WORD>

copy sftp config address {A.B.C.D | <WORD>} filename <WORD> username <WORD>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionaddress {A.B.C.D | <WORD>} Specify the IPv4 or IPv6 address of the SFTP server.filename <word> Specify the filename from which to copy the configuration.unit <1-8 | all> Select units from which the configuration should be copied.username <WORD> Provides the username for the SFTP server.



Avaya.com/support


Command: copy tftp


copy tftp

Copies configuration from a TFTP server.

Syntax

copy tftp config address {A.B.C.D | <WORD>} filename <WORD>

copy tftp config address {A.B.C.D | <WORD>} filename <WORD> unit <1-8 | all>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionaddress {A.B.C.D | <WORD>} Specify the IPv4 or IPv6 address of the TFTP server.filename <word> Specify the filename from which to copy the configuration.unit <1-8 | all> Select units from which the configuration should be copied.



Avaya.com/support


Command: copy usb


copy usb

Copies from a USB memory stick.

Syntax

copy usb config filename <WORD>

copy usb config filename <WORD> unit <1-8>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionfilename <word> Specify the filename from which to copy the configuration.unit <1-8> Copy from the USB of another unit in a stack.



Avaya.com/support


Command: csnp-interval


csnp-interval

Specifies the Complete Sequence Number Packet (CSNP) interval in seconds.

Syntax

csnp-interval <1-600>

default csnp-interval

no csnp-interval

Default

10

Command mode


Command parameters


<1-600>

Specifies the CSNP interval in seconds. This is a system level parameter that applies forlevel 1 CSNP generation on all interfaces. A longer interval reduces overhead, while ashorter interval speeds up convergence. The default value is 10. Use the no or defaultoptions to set this parameter to the default value of 10.



Avaya.com/support


Command: ddi-logging


ddi-logging

Configures logging of DDI events.

Syntax

[default] [no] ddi-logging enable port <port>

[no] ddi-logging enable

Default

Disabled

Command mode


Command parameters

Parameter Descriptionenable Enables DDI logging.port <port> Selects a port.



Avaya.com/support


Command: default-cost


default-cost

Configures the OSPF default cost metric.

Syntax

default default-cost

default default-cost {ethernet | fast-ethernet | forty-gig-ethernet | gig-ethernet | ten-

gig-ethernet}

default-cost {ethernet | fast-ethernet | forty-gig-ethernet | gig-ethernet | ten-gig-

ethernet} <1-65535>

Default

None

Command mode


Command parameters


<1-65535> Specifies the default cost metric to assign to the specified port type. The metricvalue is an integer between 1 and 65535.

ethernet Set default cost for ethernet interfacesfast-ethernet

Set default cost for fast-ethernet interfaces

forty-gig-ethernet

Set default cost for forty-gigabit-ethernet interfaces

gig-ethernet Set default cost for gigabit-ethernet interfacesten-gig-ethernet

Set default cost for ten-gigabit-ethernet interfaces



Avaya.com/support


Command: default-metric


default-metric

Configures the default RIP metric value.

Syntax

default default-metric

default-metric <0-15>

Default

None

Command mode


Command parameters

Parameter Description<0-15> Specifies a metric value between 0 and 15



Avaya.com/support


Command: diagnostics-quick-modeenable



Enables the diagnostics quick mode flag to choose the diagnostic test behavior during boot, either quick mode boot tests, or allthe diagnostic tests.

Syntax

default diagnostics-quick-mode enable


no diagnostics-quick-mode enable

Default

Disabled

Command mode




Avaya.com/support


Command: disable


disable

Turns off privileged commands and returns you to the User Exec prompt.

Syntax

disable

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: download


download

Downloads and runs a new image. If you use the download command without the optional parameters, the switch prompts you toprovide the necessary information. The switch maintains a memory and can reuse the last information entered for the downloadcommand. To reuse information, press Enter when the switch prompts you to provide details rather than typing the information.

Syntax

download

download {address | sftp address | tftp address} <A.B.C.D | WORD> diag <WORD> [no-reset]

download {address | sftp address | tftp address} <A.B.C.D | WORD> image <WORD> [no-reset]

download {address | sftp address | tftp address} <A.B.C.D | WORD> image-if-newer <WORD>

[no-reset]

download {address | sftp address | tftp address} <A.B.C.D | WORD> no-reset

download {address | sftp address | tftp address} <A.B.C.D | WORD> primary {image <WORD> |

image-if-newer <WORD>} [no-reset]

download {address | sftp address | tftp address} <A.B.C.D | WORD> secondary {image <WORD> |

image-if-newer <WORD>} [no-reset]

download usb diag <WORD> [unit <1-8>] [no-reset]

download usb image <WORD> [unit <1-8>] [no-reset]

download usb image-if-newer <WORD> [unit <1-8>] [no-reset]

download usb primary {image <WORD> | image-if-newer <WORD>} [unit <1-8>] [no-reset]

download usb secondary {image <WORD> | image-if-newer <WORD>} [unit <1-8>] [no-reset]

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description{address |sftp address| tftpaddress}

Specifies the IPv4 or IPv6 address of the TFTP or SFTP server to be used. Theaddress parameter is optional and if omitted the switch defaults to the TFTP serverspecified by the tftpserver command unless software download is to take place

<A.B.C.D |WORD>

using a USB mass storage device. The sftp address parameter appears only if theswitch runs a secure image.

diag <WORD> Specifies the name of the diagnostic image to be downloaded from the TFTP server.image <WORD> Specifies the name of the software image to be downloaded from the TFTP server.image-if-newer <WORD>

Specifies the name of the software image to be downloaded from the TFTP server ifnewer than the currently running image.

no-reset Stops the switch from resetting after the software download is complete.primary |secondary

Specifies the image to download: primary or secondary.

unit <1-8> Downloads the image from the USB of another unit in a stack.usb Downloads the image from the USB.



Avaya.com/support


Command: duplex


duplex

Configures the duplex operation of a management port.

Syntax

duplex {full | half | auto}

Default

None

Command mode




Avaya.com/support


Command: edm


edm

Configures the path information for EDM Help files.

Syntax

default edm help-file-path

default edm inactivity-timeout

edm help-file-path <WORD> tftp address <A.B.C.D | WORD>

edm help-file-path <WORD> usb [unit <1-8>]

edm inactivity-timeout <30-65535>

no edm help-file-path

no edm inactivity-timeout

Default

None

Command mode


Command parameters

Parameter Description<WORD> Specifies the directory path.inactivity-timeout Restores the inactivity timeout to the default value.tftp address <A.B.C.D | WORD> Specifies an IPv4 or IPv6 address for the TFTP server.unit <1-8> Specifies a unit number in a stack.usb Specifies the Help file is on a USB device.



Avaya.com/support


Command: enable


enable

Use this command to enter Privileged EXEC mode in ACLI.

Syntax

enable

Default

None

Command mode

User EXEC



Avaya.com/support


Command: end


end

Use this command to return to the Privileged EXEC mode from Global Configuration mode or higher.

Syntax

end

Default

None

Command mode




Avaya.com/support


Command: exit


exit

Use this command to exit a command mode and enter the lower command mode. This command works in all command modes. Ifyou issue this command in User EXEC mode, you end the current ACLI session.

Syntax

exit

Default

None

Command mode

User EXEC



Avaya.com/support


Command: fa


fa

Configures Fabric Attach.

Syntax

Default

Enabled

Command mode


Command parameters

Parameter Descriptionenable Enables multicast filter mode.



Avaya.com/support


Command: fa authentication-key


fa authentication-key

Configure Fabric Attach authentication key.

Syntax

fa authentication-key <LINE>

default fa authentication-key

Default

None

Command mode


Command parameters

Parameter Description<LINE> List of ports



Avaya.com/support


Command: fa extended-logging


fa extended-logging

Enable Fabric Attach extended logging

Syntax

fa extended-logging

no fa extended-logging

Default

Disabled

Command mode




Avaya.com/support


Command: fa message-authentication


fa message-authentication

Enable Fabric Attach message authentication.

Syntax

fa message-authentication <LINE>

no fa message-authentication

default fa message-authentication

Default

Enabled

Command mode


Command parameters

Parameter Description<LINE> List of ports



Avaya.com/support


Command: fa port-enable


fa port-enable

Enable per-port Fabric Attach operations.

Syntax

fa port-enable <LINE>

no fa port-enable

default fa port-enable

Default

Enabled

Command mode


Command parameters

Parameter Description<LINE> List of ports.



Avaya.com/support


Command: fa proxy


fa proxy

Enable Fabric Attach client proxy.

Syntax

fa proxy

no fa proxy

default fa proxy

Default

Enabled

Command mode




Avaya.com/support


Command: fa standalone-proxy


fa standalone-proxy

Enable Fabric Attach standalone proxy.

Syntax

fa standalone-proxy

no fa standalone-proxy

default fa standalone-proxy

Default

Disabled

Command mode




Avaya.com/support


Command: fa timeout


fa timeout

Configure Fabric Attach timeout.

Syntax

fa timeout <45-480>

default fa timeout

Default

75

Command mode


Command parameters

Parameter Description<45-480> Configures Fabric Attach timeout.



Avaya.com/support


Command: fa uplink


fa uplink

Configure Fabric Attach uplink data.

Syntax

fa uplink {[port <LINE>] | [trunk <1-64>]}

no fa uplink

Default

None

Command mode


Command parameters

Parameter Description<1-64> MLT Trunk ID<LINE> PortPort Uplink porttrunk Uplink trunk



Avaya.com/support


Command: fa vlan


fa vlan

Configure Fabric Attach VLANs.

Syntax

fa vlan <LINE>

no fa vlan

default fa vlan

Default

None

Command mode


Command parameters

Parameter Description<LINE> VLAN list



Avaya.com/support


Command: fa zero-touch


fa zero-touch

Enable Fabric Attach Zero Touch.

Syntax

fa zero-touch

no fa zero-touch

default fa zero-touch

Default

Enabled

Command mode




Avaya.com/support


Command: fa zero-touch-options


fa zero-touch-options

Configure Fabric Attach Zero Touch option settings.

Syntax

fa zero-touch-options [auto-pvid-mode-fa-client | auto-trusted-mode-fa-client | ip-addr-

dhcp]

no fa zero-touch-options [auto-pvid-mode-fa-client | auto-trusted-mode-fa-client | ip-

addr-dhcp]

default fa zero-touch-options

Default

Default ip-addr-dhcp is enabled

Command mode


Command parameters

Parameter Descriptionauto-pvid-mode-fa-client Enable automatic client PVID/Mgmt VLAN updateauto-trusted-mode-fa-client Enable automatic trusted client connectionip-addr-dhcp Enable automated DHCP IP address acquisition



Avaya.com/support


Command: fcoe controller


fcoe controller

Configures the FCoE Network Controller (FNC) MAC address data.

Syntax

Default

None

Command mode


Command parameters


<H.H.H>Specifies the FNC MAC Address. You must provide the FNC MAC address, ingressinterface, and VLAN so that certain types of traffic generated by the FNC can receivepreferential treatment.

port<port>

Specifies the FNC port.

vlan <1-4094>

Specifies the VLAN ID value for the controller.



Avaya.com/support


Command: fcoe controller-access


fcoe controller-access

Allows or blocks the global FCoE Redirect external FNC access setting.

Syntax

fcoe controller-access <allow | block>

Default

Denied

Command mode


Command parameters

Parameter Description<allow | block> Allows or blocks access.



Avaya.com/support


Command: fcoe oper-mode


fcoe oper-mode

Enables the global FCoE Redirect operation mode.

Syntax

default fcoe [oper-mode]

fcoe oper-mode [enable]

no fcoe oper-mode [enable]

Default

Disabled

Command mode


Command parameters


enable Initiates validation and reservation of the resources that are required for serviceactivation. If resources are not available, the enable request is rejected.



Avaya.com/support


Command: fcoe profile


fcoe profile

This command is included only for reference. Traffic profiles are automatically created on the VSP7000 switch by the FNC and donot need to be manually configured. DO NOT manually configure FCoE traffic profiles.

Syntax

default fcoe [profile]

fcoe profile d-id <H.H.H> port-list <port> update-dst-mac <H.H.H> update-src-mac <H.H.H>

egress-port <port> [ethertype <0x0-0xFFFF>] [name <WORD>] [priority <0–7>] [s-id <H.H.H> ]

[vlan-min <1–4094> vlan-max <1–4094>]

fcoe profile d-id <H.H.H> port-list <port> update-dst-mac <H.H.H> update-src-mac <H.H.H>

egress-trunk <1-64> [ethertype <0x0-0xFFFF>] [name <WORD>] [priority <0–7>] [s-id <H.H.H> ]

[vlan-min <1–4094> vlan-max <1–4094>]

no fcoe profile [<1-55000>]

Default

None

Command mode


Command parameters

Parameter Description<1-55000> Specifies the FCoE profile ID.

d-id <H.H.H> Specifies the three-octet Fiber Channel Destination ID (D_ID) valuefor performing stream identification.

egress-port <port> Specifies the egress port.egress-trunk <1-64> Specifies the egress trunk.ethertype <0x0-0xFFFF> Specifies the ethertype match criteria. The default is 0x8906.name <WORD> Specifies the entry label data.port-list <port> Specifies the ingress port-list criteria.priority <0–7> Specifies the user priority match criteria. The default is ignore.

s-id <H.H.H> Specifies the Fiber Channel Source ID (S_ID) for performing streamidentification. The default is ignore.

update-dst-mac <H.H.H> Specifies the non-zero six-octet update action destination MACaddress.

update-src-mac <H.H.H> Specifies the six-octet update action source MAC address.vlan-min <1–4094> vlan-max <1–4094>

Specifies the minimum and maximum VLAN ID match criteria.



Avaya.com/support


Command: flowcontrol


flowcontrol

Configures the flow control mode of a port.

Syntax

default flowcontrol [port <port>]

flowcontrol [port <port>] {asymmetric | symmetric | auto |disable}

no flowcontrol [port <port>]

Default

Automatic

Command mode


Command parameters

Parameter Descriptionasymmetric Set the mode for flow control. PAUSE frames can flow only in one direction.auto Set the port to automatically determine the flow control mode (default).disable Disable flow control on the port.port <port> Specify the port numbers to configure for flow control.symmetric Set the mode for flow control. PAUSE frames can flow in either direction.



Avaya.com/support


Command: help


help

Use this command to see parameters for a particular command. You can use this command in any mode. You can also requestHelp at any point by entering a question mark after a command, which shows the available options.

Syntax

help

help commands

help commands mode application

help commands mode config

help commands mode current

help commands mode exec

help commands mode ifconfig

help commands mode interface <Ethernet|loopback|vlan>

help commands mode privExec

help commands mode router <ospf|rip|vrrp>

help modes

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptioncommands Shows commands available by mode.

mode application Shows commands available in Application Configurationmode.

mode config Shows commands available in Global Configuration mode.

mode current Shows commands available in the current configurationmode.

mode exec Shows commands available in User EXEC mode.

mode ifconfig Shows commands available in Interface Configurationmode.

mode interface<Ethernet|loopback|vlan>

Shows commands available in a specific InterfaceConfiguration mode.

mode privExec Shows commands available in Privileged EXECConfiguration mode.

mode router <ospf|rip|vrrp> Shows commands available in Router Configuration mode.

modes Shows available modes with information about how toenter each mode.



Avaya.com/support


Command: host-route


host-route

Adds a host to a router.

Syntax

default host-route {A.B.C.D}

host-route {A.B.C.D} metric <0-65535>

no host-route {A.B.C.D}

Default

None

Command mode


Command parameters

Parameter Description{A.B.C.D} Specifies the host IP addressmetric <0-65535>

Specifies an integer between 0 and 65535 representing the configured cost of thehost route.



Avaya.com/support


Command: http-port


http-port

Configures the TCP port on which web server will listen.

Syntax

default http-port

http-port <1024-65535>

Default

80

Command mode


Command parameters

Parameter Description<1024-65535> Specifies the TCP port.



Avaya.com/support


Command: https-only


https-only

Enables only HTTPS. If SSL is enables , the web server listens only on the HTTPS port. This command appears only if the switchruns a secure image.

Syntax

default https-only

https-only

no https-only

Default

Enabled

Command mode




Avaya.com/support


Command: https-port


https-port

Configures the TCP port on which web server will listen.

Syntax

default https-port

https-port <1024-65535>

Default

443

Command mode


Command parameters

Parameter Description<1024-65535> Specifies the port number.



Avaya.com/support


Command: install


install

Runs a quick install and setup script.

Syntax

install

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: interface Ethernet


interface Ethernet

Use this command to enter Interface Configuration mode for an Ethernet port.

Syntax

interface Ethernet <port>

Default

None

Command mode


Command parameters

Parameter Description<port> Specifies a port or list of ports.



Avaya.com/support


Command: interface loopback


interface loopback

Use this command to enter Interface Configuration mode for a loopback interface.

Syntax

interface loopback <1-16>

Default

None

Command mode


Command parameters

Parameter Description<1-16> Specifies the loopback ID.



Avaya.com/support


Command: interface mgmt


interface mgmt

Use this command to enter Interface Configuration mode for a management interface.

Syntax

interface mgmt <1-8>

Default

None

Command mode


Command parameters

Parameter Description<1-8> Specifies the interface ID value.



Avaya.com/support


Command: interface mlt


interface mlt

Use this command to enter Interface Configuration mode for an MLT.

Syntax

interface mlt <1-64>

Default

None

Command mode


Command parameters

Parameter Description<1-64> Specifies the MLT ID.



Avaya.com/support


Command: interface vlan


interface vlan

Use this command to enter Interface Configuration mode for a VLAN.

Syntax

interface Vlan <1-4094>

Default

None

Command mode


Command parameters

Parameter Description<1-4094> Specifies the VLAN ID.



Avaya.com/support


Command: ip address (GlobalConfiguration)


ip address (Global Configuration)

Configures the switch or stack address.

Syntax

default ip address

default ip address source

ip address [stack | switch ] {A.B.C.D} [A.B.C.D] [default-gateway {A.B.C.D}] [netmask

{A.B.C.D}]

ip address netmask {A.B.C.D} [default-gateway {A.B.C.D}]

ip address source source {bootp-always | bootp-last-address | bootp-when-needed |

configured-address | dhcp-always | dhcp-last-address | dhcp-when-needed}

ip address unit <1-8> {A.B.C.D}

no ip address [stack] [switch] [unit <1-8>]

Default

None

Command mode


Command parameters

Parameter DescriptionA.B.C.D Specifies the IP address or subnet mask.bootp-always Always use the bootp server.bootp-last-address Use the last time bootp server.bootp-when-needed Use bootp server when needed.configured-address Use a user-configured IP address.default-gateway {A.B.C.D} Configures the default-gateway address.dhcp-always Always use the DHCP server.dhcp-last-address Use the last time DHCP server.dhcp-when-needed Use DHCP client when needed.netmask {A.B.C.D} Spcifies the subnet mask.source Configures default BootP/DHCP settings.stack Configures the address of the stack.

switch Configures the IP address of local unit.unit <1-8> {A.B.C.D} Configures the IP address of another unit in a stack.



Avaya.com/support


Command: ip address (VLAN InterfaceConfiguration)


ip address (VLAN Interface Configuration)

Assigns an IP addr to a vlan.

Syntax

default ip address [source]

ip address <A.B.C.D> <subnet_mask> [ <mac-offset> ]

no ip address <A.B.C.D> <subnet_mask>

Default

None

Command mode


Command parameters

Parameter Description<subnet_mask> Specifies the subnet mask to associate with the VLAN IP address.<A.B.C.D> Assigns the IP address to the VLAN .

<mac-offset>Specifies the value used to calculate the VLAN MAC address, which is offset fromthe switch MAC address. The valid range is 1-256, with the value of 1 reserved forthe Management VLAN.



Avaya.com/support


Command: ip arp-inspection (EthernetInterface Configuration)


ip arp-inspection (Ethernet Interface Configuration)

Specifies whether a particular port or range of ports is trusted (ARP traffic is not subject to dynamic ARP inspection) or untrusted(ARP traffic is subject to dynamic ARP inspection).

Syntax

default ip arp-inspection [port <port>]

ip arp-inspection [port <port>] {trusted|untrusted}

Default

untrusted

Command mode


Command parameters

Parameter Descriptionport <port> Specify list of ports.trusted ARP traffic is not subject to dynamic ARP inspection.untrusted ARP traffic is subject to dynamic ARP inspection.



Avaya.com/support


Command: ip arp-inspection (GlobalConfiguration)


ip arp-inspection (Global Configuration)

Enables ARP inspection.

Syntax

ip arp-inspection vlan <1-4094>

no ip arp-inspection vlan [<1-4094>]

Default

Disabled

Command mode


Command parameters

Parameter Descriptionvlan <1-4094> Specifies a VLAN ID.



Avaya.com/support


Command: ip arp-proxy


ip arp-proxy

Configures proxy ARP status on a VLAN.

Syntax

[no] ip arp-proxy enable

default ip arp-proxy [enable]

Default

Disabled

Command mode


Command parameters

Parameter Descriptionenable Enable Proxy ARP



Avaya.com/support


Command: ip blocking-mode


ip blocking-mode

Configures the Layer 3 IP blocking mode.

Syntax

default ip blocking-mode

ip blocking-mode <full | none>

Default

None

Command mode


Command parameters

Parameter Descriptionfull Specifies IP blocking as full, which never allows a duplicate IP address in a stack.

none Specifies IP blocking as none, which allows duplicate IP addresses unconditionally. Thedefault is none.



Avaya.com/support


Command: ip bootp


ip bootp

Configures the BOOTP server.

Syntax

default ip bootp server

ip bootp server <always | disable | last | needed>

no ip bootp server

Default

None

Command mode


Command parameters

Parameter Descriptionalways Always use the BOOTP serverdisable Never use BOOTP server.last Use the last time BOOTP server.needed Use BOOTP server when needed.



Avaya.com/support


Command: ip default-gateway


ip default-gateway

Specifies the default gateway, if the switch doesn't route IP.

Syntax

default ip default-gateway

ip default-gateway <A.B.C.D>

no ip default-gateway

Default

None

Command mode


Command parameters

Parameter Description<A.B.C.D> Specifies the IP address of the default gateway.



Avaya.com/support


Command: ip dhcp client lease


ip dhcp client lease

Configues the DHCP client.

Syntax

default ip dhcp client lease

ip dhcp client lease <10-4294967295>

ip dhcp client lease days <1-49710>

ip dhcp client lease hours <1-1193046>

ip dhcp client lease minutes <1-71582788>

ip dhcp client lease weeks <1-7101>

no ip dhcp client lease

Default

None

Command mode


Command parameters

Parameter Description<10-4294967295> Specifies the lease time in seconds.days <1-49710> Specifies the lease time in days.hours <1-1193046> Specifies the lease time in hours.minutes <1-71582788> Specifies the lease time in minutes.weeks <1-7101> Specifies the lease time in weeks.



Avaya.com/support


Command: ip dhcp-relay (EthernetInterface Configuration)


ip dhcp-relay (Ethernet Interface Configuration)

Configures DHCP relay for a port.

Syntax

default ip dhcp-relay [port <port>] option82-subscriber-id

ip dhcp-relay [port <port>] option82-subscriber-id <WORD>

no ip dhcp-relay [port <port>] option82-subscriber-id

Default

None

Command mode


Command parameters

Parameter Descriptionoption82-subscriber-id<WORD>

Specifies the DHCP Option 82 subscriber ID for the port. Value is acharacter string between 0 and 64 characters.



Avaya.com/support


Command: ip dhcp-relay (GlobalConfiguration)


ip dhcp-relay (Global Configuration)

Configures DHCP relay globally.

Syntax

default ip dhcp-relay

default ip dhcp-relay max-frame

default ip dhcp-relay option82

ip dhcp-relay

ip dhcp-relay fwd-path <A.B.C.D> <A.B.C.D> [disable] [enable] [mode {bootp | bootp-dhcp |

dhcp} ]

ip dhcp-relay max-frame <576-1536>

ip dhcp-relay option82

no ip dhcp-relay

no ip dhcp-relay fwd-path <A.B.C.D> <A.B.C.D>

no ip dhcp-relay option82

Default

Enabled

Command mode


Command parameters

Parameter Descriptiondisable Disables the forwarding path.enable Enables the forwarding path.fwd-path <A.B.C.D><A.B.C.D>

Configures the forwarding path from the client to the server. Specify theagent and server IP addresses.

max-frame <576-1536> Configures the maximum length for which option82 is added to DHCPpackets for relay. The default is 576.

mode {bootp | bootp-dhcp | dhcp}

Configures the mode supported by the forwarding path.

option82 Enables Option 82 for DHCP relay. The default is disabled.

Avaya Virtual Services Platform 7000 Series Release 10.4

NN47202-600 Avaya Command Line Interface Commands ReferenceVersion 04.01 July 2015



Command: ip dhcp-relay (VLANInterface Configuration)


ip dhcp-relay (VLAN Interface Configuration)

Configures DHCP relay for a vlan.

Syntax

default ip dhcp-relay option82

ip dhcp-relay

ip dhcp-relay broadcast

ip dhcp-relay clear-counters

ip dhcp-relay min-sec <0-65535>

ip dhcp-relay min-sec <0-65535> mode {bootp | bootp-dhcp | dhcp}

ip dhcp-relay mode {bootp | bootp-dhcp | dhcp}

ip dhcp-relay option82

no ip dhcp-relay

no ip dhcp-relay broadcast

no ip dhcp-relay option82

Default

None

Command mode


Command parameters


broadcast Enables the broadcast of DHCP reply packets to the DHCP clients on this VLANinterface

clear-counters

Clears the DHCP relay coutners for the VLAN.

min-sec<minsec>

Indicates the min-sec value. The switch immediately forwards a BootP/DHCP packetif the secs field in the BootP/DHCP packet header is greater than the configured min-sec value; otherwise, the packet is dropped. Range is 0-65535. The default is 0.

mode {bootp|dhcp|bootp_dhcp}

Specifies the type of DHCP packets this VLAN supports: bootp - Supports BootP only;dhcp - Supports DHCP only; bootp_dhcp - Supports both BootP and DHCP.

option82 Enables Option 82 for DHCP relay on a VLAN.



Avaya.com/support


Command: ip dhcp-snooping binding


ip dhcp-snooping binding

Adds a static DHCP snooping binding table entry.

Syntax

ip dhcp-snooping binding <1-4094> <H.H.H> ip <A.B.C.D> port <port> [expiry <1-4294967295>]

no ip dhcp-snooping binding <1-4094> <H.H.H>

Default

None

Command mode


Command parameters

Parameter Description<1-4094> Specifies a VLAN ID.<H.H.H> Specifies the MAC address to add.expiry <1-4294967295> Configures the expiry time.ip <A.B.C.D> Specifies the IP address.port <port> Specifies the port on which the device connects.



Avaya.com/support


Command: ip dhcp-snooping (EthernetInterface Configuration)


ip dhcp-snooping (Ethernet Interface Configuration)

Configures DHCP snooping port settings.

Syntax

default ip dhcp-snooping [port <port>]

default ip dhcp-snooping [port <port>] option82-subscriber-id

ip dhcp-snooping [port <port>] <trusted | untrusted>

ip dhcp-snooping [port <port>] option82-subscriber-id <WORD>

no ip dhcp-snooping [port <port>] option82-subscriber-id

Default

None

Command mode


Command parameters

Parameter Descriptionoption82-subscriber-id<WORD>

Specifies the DHCP Option 82 subscriber ID for the port. Value is acharacter string between 0 and 64 characters.

port <port> Specifies a port or group of ports.trusted When selected, the port or ports automatically forward DHCP replies.

untrusted When selected, the port or ports filter DHCP replies through DHCPsnooping.



Avaya.com/support


Command: ip dhcp-snooping external-save


ip dhcp-snooping external-save

Controls the external DHCP snooping binding table saving.

Syntax

default ip dhcp-snooping external-save

ip dhcp-snooping external-save enable

ip dhcp-snooping external-save tftp {A.B.C.D | WORD} filename <WORD>

ip dhcp-snooping external-save usb [unit <1-8>] filename <WORD>

no ip dhcp-snooping external-save [enable]

Default

Disabled

Command mode


Command parameters

Parameter Descriptiontftp {A.B.C.D |WORD}

Saves the binding table on a TFTP server. Provide an IPv4 or IPv6address.

enable Enables external saving of the binding table. The default is disabled.filename <WORD> Identifies the binding table external file.unit <1-8> Specifies a unit number in a stack.usb Saves the binding table on USB.



Avaya.com/support


Command: ip dhcp-snooping external-save restore


ip dhcp-snooping external-save restore

Controls the external DHCP snooping binding table saving.

Syntax

ip dhcp-snooping external-save restore

Default

Disabled

Command mode

Privileged EXEC



Avaya.com/support


Command: ip dhcp-snooping (GlobalConfiguration)


ip dhcp-snooping (Global Configuration)

Configures DHCP snooping settings globally.

Syntax

default ip dhcp-snooping

default ip dhcp-snooping vlan <VLAN list>

ip dhcp-snooping

ip dhcp-snooping enable

ip dhcp-snooping option 82

ip dhcp-snooping vlan <VLAN list>

no ip dhcp-snooping

no ip dhcp-snooping option 82

no ip dhcp-snooping vlan [<VLAN list>]

Default

None

Command mode


Command parameters

Parameter Descriptionenable Enables DHCP snooping. The default is disabled.option 82 Enables Option 82 for DHCP snooping. The default is disabled.vlan <VLAN list> Enables DHCP snooping for a VLAN.



Avaya.com/support


Command: ip directed-broadcast enable


ip directed-broadcast enable

Enables directed broadcast forwarding.

Syntax

default ip directed-broadcast enable

ip directed-broadcast enable

no ip directed-broadcast enable

Default

Disabled

Command mode




Avaya.com/support


Command: ip directed-broadcast (VLANInterface Configuration)


ip directed-broadcast (VLAN Interface Configuration)

Configure IP directed-broadcast on a VLAN

Syntax

default ip directed-broadcast [enable]

ip directed-broadcast [enable]

no ip directed-broadcast [enable]

Default

Disabled

Command mode


Command parameters

Parameter Descriptionenable Enable IP directed broadcast



Avaya.com/support


Command: ip domain-name


ip domain-name

Configures the DNS domain name.

Syntax

default ip domain-name

ip domain-name <domain-name>

no ip domain-name

Default

None

Command mode


Command parameters

Parameter Description<domain-name>

Specifies the default domain name to be used. A domain name is determined to be validif it contains alphanumeric characters and contains at least one period (.).



Avaya.com/support


Command: ip forward-protocol udp(Global Configuration)


ip forward-protocol udp (Global Configuration)

Configures broadcast forwarding.

Syntax

ip forward-protocol udp <1-65535> <word>

ip forward-protocol udp portfwdlist <1-128> <1-65535> <A.B.C.D> [name <WORD>]

no ip forward-protocol udp <1-65535>

no ip forward-protocol udp portfwdlist <1-128> [<1-65535> <A.B.C.D>]

Default

None

Command mode


Command parameters

Parameter Description<1-65535> Specifies the UDP port to forward.<A.B.C.D> Specifies the IP destination for the UDP port.<WORD> Specifies the protocol name.name <WORD> Specifies a name for the list.portfwdlist <1-128> Creates a port forwarding list for a list of ports.



Avaya.com/support


Command: ip forward-protocol udp(VLAN Interface Configuration)


ip forward-protocol udp (VLAN Interface Configuration)

Associates a UDP forwarding list with a VLAN interface.

Syntax

default ip forward-protocol udp [vlan <1-4094>] [broadcastmask] [maxttl]

ip forward-protocol udp [vlan <1-4094>] [portfwdlist <1-128>] [broadcastmask <A.B.C.D>]

[maxttl <1-16>]

no ip forward-protocol udp [vlan <1-4094>] [portfwdlist [<1-128>]] [broadcastmask]

Default

None

Command mode


Command parameters


broadcastmask<A.B.C.D>

Specifies the 32-bit mask used by the selected VLAN interface to make forwardingdecisions based on the destination IP address of the incoming UDP broadcasttraffic. If you do not specify a broadcast mask value, the switch uses the mask ofthe interface to which the forwarding list is attached.

maxttl <1-16>

Specifies the timet-to-live (TTL) value inserted in the IP headers of the forwardedUDP packets coming out of the selected VLAN interface. If you do not specify a TTLvalue, the default value (4) is used.

portfwdlist<1-128>

Specifies the ID of the UDP forwarding list to attach to the selected VLAN interface.

vlan <1-4094>

Specifies the VLAN ID on which to attach the UDP forwarding list. This parameter isoptional, and if not specified, the UDP forwarding list is applied to the interfacespecified in the interface vlan command.



Avaya.com/support


Command: ip fwd-nh (GlobalConfiguration)


ip fwd-nh (Global Configuration)

Configure IP forwarding next-hop settings.

Syntax

default ip fwd-nh

default ip fwd-nh enable

default ip fwd-nh policy [<WORD>]

ip fwd-nh

ip fwd-nh enable

ip fwd-nh policy <WORD> match source-ip <A.B.C.D/0-32> [port-type {both | tcp | udp}] port-

min <0-65535> port-max <0-65535> set next-hop <A.B.C.D> [secondary-next-hop <A.B.C.D>]

no ip fwd-nh

no ip fwd-nh enable

no ip fwd-nh policy <WORD>

Default

None

Command mode


Command parameters

Parameter Descriptionenable Enables IP forwarding next-hop.match source-ip <A.B.C.D/0-32>

Specifies the source IP address and mask length to be matched. IP address0.0.0.0 is not supported.

next-hop<A.B.C.D>

Specifies the next hop IP address to be used to forward the packet. The nexthop must be a direct connection to any of the routing interfaces of the switch.

policy <WORD> Specifies the name of the next-hop forwarding policy. The value consists of anyalphanumeric values.

port-max <0-65535>

Specifies the maximum Layer 4 port value.

port-min <0-Specifies the minimum Layer 4 port value.

65535>

port-type{both | tcp |udp}

Specifies the port type.

secondary-next-hop<A.B.C.D>

Specifies a secondary next hop to use if the next hop is not reachable.

set Specifies the policy set parameters.



Avaya.com/support


Command: ip fwd-nh (VLAN InterfaceConfiguration)


ip fwd-nh (VLAN Interface Configuration)

Configure IP forwarding next-hop configuration settings.

Syntax

default ip fwd-nh policy [<WORD>]

ip fwd-nh { [admin-status <disable|enable>] | [policy <WORD> mode <drop|normal-routing>]}

no ip fwd-nh policy [<WORD>]

Default

None

Command mode


Command parameters

Parameter Descriptionadmin-status<disable|enable>

Specifies IP fowarding administrative status for all policies.

mode <drop |normail-routing>

Specify the packet forwarding decision to be made when the next-hop isnot reachable. Default is normal-routing.

policy <WORD> Specify the name of the next-hop forwarding policy.



Avaya.com/support


Command: ip igmp


ip igmp

Creates a new IGMP interface.

Syntax

default ip igmp

ip igmp

no ip igmp

Default

None

Command mode




Avaya.com/support


Command: ip igmp filter


ip igmp filter

Adds IGMP filter profile to interface.

Syntax

default ip igmp filter [<1-65535>]

ip igmp filter <1-65535>

no ip igmp filter [<1-65535>]

Default

None

Command mode


Command parameters

Parameter Description<1-65535> Add IGMP filter profile to interface.



Avaya.com/support


Command: ip igmp flush


ip igmp flush

Flush IGMP group members or mrouter members from the IGMP routing table.

Syntax

ip igmp flush Ethernet [<port>]

ip igmp flush vlan <1-4094> {grp-member | mrouter}

Default

None

Command mode


Command parameters

Parameter DescriptionEthernet [<port>] Flushes the port or list of ports.vlan <1-4094> {grp-member |mrouter}

Flushes the group member or mrouter for the specifiedVLAN.



Avaya.com/support


Command: ip igmp last-member-query-interval


ip igmp last-member-query-interval

Sets the maximum response time (in tenths of a second) that is inserted into group-specific queries that are sent in response toleave group messages.

Syntax

default ip igmp last-member-query-interval

ip igmp last-member-query-interval <0-255>

Default

10

Command mode


Command parameters


<0-255>Specify the last member query interval in 1/10 of a second. Avaya recommends that youconfigure this parameter to values higher than 3. If a fast leave process is not required,Avaya recommends values above 10.



Avaya.com/support


Command: ip igmp mrouter


ip igmp mrouter

Adds one or more static mrouter ports to a VLAN.

Syntax

default ip igmp mrouter

ip igmp mrouter <port_list>

no ip igmp mrouter [<port_list>]

Default

None

Command mode


Command parameters

Parameter Description<port_list> Specifies the port or ports to add to the VLAN as static mrouter ports.



Avaya.com/support


Command: ip igmp profile


ip igmp profile

Creates or modifies an IGMP filter profile.

Syntax

default ip igmp profile <1-65535>

ip igmp profile <1-65535>

no ip igmp profile <1-65535>

Default

None

Command mode


Command parameters

Parameter Description<1-65535> Specifies the profile ID.



Avaya.com/support


Command: ip igmp proxy


ip igmp proxy

Enables or disables IGMP proxy on a VLAN.

Syntax

[default] [no] ip igmp proxy

Default

Disabled

Command mode




Avaya.com/support


Command: ip igmp query-interval


ip igmp query-interval

Sets the frequency (in seconds) at which host query packets are transmitted on the VLAN.

Syntax

ip igmp query-interval <1-65535>

default ip igmp query-interval

Default

125

Command mode


Command parameters

Parameter Description<1-65535> Specifies the query interval value. Values range from 1 to 65535 seconds.



Avaya.com/support


Command: ip igmp query-max-response


ip igmp query-max-response

Sets the maximum response time (in tenths of a second) that is advertised in IGMPv2 general queries on the VLAN.

Syntax

default ip igmp query-max-response

ip igmp query-max-response <0-255>

Default

100

Command mode


Command parameters

Parameter Description<2-255> Specifies a numerical value for IGMP snooping robustness. Values range from 2 to 255.



Avaya.com/support


Command: ip igmp robust-value


ip igmp robust-value

Sets the robustness value for a VLAN. With IGMP snooping robustness, the switch can offset expected packet loss on a subnet.

Syntax

default ip igmp robust-value

ip igmp robust-value <2-255>

Default

2

Command mode


Command parameters

Parameter Description<2-255> Specifies a numerical value for IGMP snooping robustness. Values range from 2 to 255.



Avaya.com/support


Command: ip igmp router-alert


ip igmp router-alert

Enables the router alert feature. This feature instructs the router to drop control packets that do not have the router-alert flag inthe IP header.

Syntax

[default] [no] ip igmp router-alert

Default

None

Command mode




Avaya.com/support


Command: ip igmp send-query


ip igmp send-query

Enables or disables IGMP send query on a snoop-enabled VLAN.

Syntax

[default] [no] ip igmp send-query

Default

None

Command mode




Avaya.com/support


Command: ip igmp snooping


ip igmp snooping

Enables or disables IGMP snooping for a VLAN.

Syntax

[default] [no] ip igmp snooping

Default

None

Command mode




Avaya.com/support


Command: ip igmp version


ip igmp version

Configures the IGMP version running on the VLAN.

Syntax

default ip igmp version

ip igmp version <1-3>

Default

IGMPv2

Command mode


Command parameters

Parameter Description<1-3> Specifies the IGMP version: 1—IGMPv1; 2—IGMPv2; 3—IGMPv3.



Avaya.com/support


Command: ip ipfix collector


ip ipfix collector

Configures IPFIX collectors.

Syntax

default ip ipfix collector <A.B.C.D> [dest-port]

default ip ipfix collector <A.B.C.D> [enable]

ip ipfix collector <A.B.C.D> [dest-port <1-65535>]

ip ipfix collector <A.B.C.D> [enable]

no ip ipfix collector <A.B.C.D> [enable]

Default

None

Command mode


Command parameters

Parameter Description<A.B.C.D> Specifies the IPFIX collector IP address.dest-port <1-65535>

Specifies the port on which the collector listens for IPFIX data. The default is9995.

enable Creates and enables a new IPFIX collector, or enables an existing IPFIX collector.The default is enabled.



Avaya.com/support


Command: ip ipfix enable


ip ipfix enable

Enables or disables IPFIX.

Syntax

default ip ipfix enable

ip ipfix enable

no ip ipfix enable

Default

Disabled

Command mode




Avaya.com/support


Command: ip ipfix (Ethernet InterfaceConfiguration)


ip ipfix (Ethernet Interface Configuration)

Enables IPFIX for one or more ports.

Syntax

default ip ipfix [port <port>] [enable]

ip ipfix [port <port>] enable

no ip ipfix [port <port>] [enable]

Default

Disabled

Command mode


Command parameters

Parameter Descriptionenable Enables IPFIX on the port.port <port> Specifies a port or list of ports.



Avaya.com/support


Command: ip ipfix flush port


ip ipfix flush port

Exports or flushes IPFIX port data.

Syntax

ip ipfix flush port <port>

ip ipfix flush port <port> export-and-flush

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionexport-and-flush Exports and flushes port data.port <port> Specifies the port for which to flush IPFIX data.



Avaya.com/support


Command: ip ipfix (GlobalConfiguration)


ip ipfix (Global Configuration)

Configures global IPFIX settings.

Syntax

default ip ipfix exporter-enable

default ip ipfix export-interval

default ip ipfix template-refresh-interval

default ip ipfix template-refresh-packets

ip ipfix exporter-enable

ip ipfix export-interval <10-3600>

ip ipfix template-refresh-interval <300-3600>

ip ipfix template-refresh-packets <10000-100000>

no ip ipfix exporter-enable

Default

None

Command mode


Command parameters

Parameter Descriptionexporter-enable Globally enables the IPFIX exporter.export-interval <10-3600> Specifies the IPFIX export interval in seconds. The default is 50.template-refresh-interval<300-3600>

Specifies the IPFIX template refresh interval in seconds. Thedefault is 1800.

template-refresh-packets<10000-100000>

Specifies the maximum number of IPFIX template packets atrefresh. The default is 10000.



Avaya.com/support


Command: ip ipfix slot


ip ipfix slot

Configures IPFIX on an slot or unit.

Syntax

default ip ipfix slot <unit number> aging-interval

ip ipfix slot <unit number> aging-interval <0-2147400>

Default

None

Command mode


Command parameters


<unit number> Specifies the position of a switch within a stack environment. If your switch isa standalone unit, use a value of 1.

aging-interval<0-2147400>

Specifies the aging interval of the flow record in seconds. The default is86400.



Avaya.com/support


Command: ip (Loopback InterfaceConfiguration)


ip (Loopback Interface Configuration)

Configure L3 parameters on a loopback interface

Syntax

default ip { area | ospf }

ip {address <A.B.C.D> <A.B.C.D> | area <A.B.C.D> | ospf }

no ip {address <A.B.C.D><A.B.C.D> | area | ospf }

Default

None

Command mode


Command parameters

Parameter Descriptionaddress <A.B.C.D> <A.B.C.D> Set an IP addressarea <A.B.C.D> Assign loopback interface to areaospf Enable OSPF on a loopback interface



Avaya.com/support


Command: ip mgmt address


ip mgmt address

Configures the switch or stack management IP address.

Syntax

default ip mgmt address

ip mgmt address [stack | switch] <A.B.C.D>

no ip mgmt address [stack | switch]

Default

None

Command mode


Command parameters

Parameter Description[stack |switch]

Specifies an out-of-band management IP address for an individual switch or thestack.

<A.B.C.D> Specifies the management IP address.



Avaya.com/support


Command: ip mgmt default-gateway


ip mgmt default-gateway

Specifies the management default gateway if the switch is not routing IP.

Syntax

default ip mgmt default-gateway

ip mgmt default-gateway <A.B.C.D>

no ip mgmt default-gateway

Default

None

Command mode


Command parameters

Parameter Description<A.B.C.D> Specifies the IP address.



Avaya.com/support


Command: ip mgmt limit


ip mgmt limit

Configures the packet-per-second limit at which the OOB port will automatically shutdown.

Syntax

default ip mgmt limit

ip mgmt limit <50-10000>

Default

None

Command mode


Command parameters

Parameter Description<50-10000> Specifies the number of packets per second.



Avaya.com/support


Command: ip mgmt netmask


ip mgmt netmask

Configures the management subnet mask.

Syntax

default ip mgmt netmask [unit <1-8>]

ip mgmt netmask [unit <1-8>] <A.B.C.D>

no ip mgmt netmask [unit <1-8>]

Default

None

Command mode


Command parameters

Parameter Description<A.B.C.D> Specifies the subnet mask.unit <1-8> Specifies the unit number in a stack.



Avaya.com/support


Command: ip mgmt route


ip mgmt route

Configures a static route for the management VLAN.

Syntax

ip mgmt route <A.B.C.D> <A.B.C.D> <A.B.C.D>

no ip mgmt route <A.B.C.D> <A.B.C.D> <A.B.C.D>

Default

None

Command mode


Command parameters

Parameter Description<A.B.C.D> <A.B.C.D><A.B.C.D>

Specifies the destination IP, destination subnet mask, andgateway IP.



Avaya.com/support


Command: ip mgmt shutdown


ip mgmt shutdown

Shuts down the management port.

Syntax

ip mgmt shutdown [all | unit <1-8>]

no ip mgmt shutdown [all | unit <1-8>]

Default

None

Command mode


Command parameters

Parameter Descriptionall | unit <1-8> Shuts down management ports in all units in the stack or in a specific unit.



Avaya.com/support


Command: ip mgmt shutdown-interval


ip mgmt shutdown-interval

Configures the management port shutdown time.

Syntax

default ip mgmt shutdown-interval

ip mgmt shutdown-interval <0-180>

Default

None

Command mode


Command parameters

Parameter Description<0-180> Specifies the shutdown time, in seconds.



Avaya.com/support


Command: ipmgr


ipmgr

Modifies IP Manager settings.

Syntax

default ipmgr snmp

default ipmgr source-ip

default ipmgr source-ip <1-50>

default ipmgr source-ip <51-100>

default ipmgr telnet

default ipmgr web

ipmgr snmp

ipmgr source-ip <1-50> <A.B.C.D> mask <A.B.C.D>

ipmgr source-ip <51-100> <WORD>

ipmgr telnet

ipmgr web

no ipmgr snmp

no ipmgr source-ip

no ipmgr source-ip <1-50>

no ipmgr source-ip <51-100>

no ipmgr telnet

no ipmgr web

Default

None

Command mode


Command parameters


<1-50> Selects the IPv4 address and mask pair.<51-100> Selects the IPv6 address and prefix.<A.B.C.D> Specifies the IPv4 address.<WORD> Specifies the IPv6 address/prefix.mask <A.B.C.D> Configures the IP mask.snmp Enables IP Manager control over SNMP traffic.source-ip Configures the source address from which connections are allowed.telnet Enables IP Manager control over Telnet sessions.web Enable IP Manager control over web connections.



Avaya.com/support


Command: ip name-server


ip name-server

Configures the address for the DNS server.

Syntax

ip name-server <A.B.C.D | WORD>

no ip name-server <A.B.C.D | WORD>

Default

None

Command mode


Command parameters

Parameter Description<A.B.C.D | WORD> Specifies the IPv4 or IPv6 address.



Avaya.com/support


Command: ip ospf advertise-when-down enable (Ethernet InterfaceConfiguration)


ip ospf advertise-when-down enable (Ethernet InterfaceConfiguration)

Enables the advertisement of the OSPF interface, and even if the port or VLAN for the routing interface subsequently goes down,the switch continues to advertise the route.

Syntax

default ip ospf [port <port>] advertise-when-down enable

ip ospf [port <port>] advertise-when-down enable

no ip ospf [port <port>] advertise-when-down enable

Default

Disabled

Command mode


Command parameters

Parameter Descriptionport <port> Selects a port or list of ports.



Avaya.com/support


Command: ip ospf advertise-when-down enable (VLAN InterfaceConfiguration)


ip ospf advertise-when-down enable (VLAN InterfaceConfiguration)

Enables the advertisement of the OSPF interface, and even if the port or VLAN for the routing interface subsequently goes down,the switch continues to advertise the route.

Syntax

default ip ospf advertise-when-down enable

ip ospf advertise-when-down enable

no ip ospf advertise-when-down enable

Default

Disabled

Command mode




Avaya.com/support


Command: ip ospf apply accept


ip ospf apply accept

Apply OSPF accept policy changes to allow the configuration changes in the policy to take effect in an OSPF Accept context (andto prevent the switch from attempting to apply the changes one by one after each configuration change).

Syntax

ip ospf apply accept

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: ip ospf apply redistribute


ip ospf apply redistribute

Apply the OSPF redistribution.

Syntax

ip ospf apply redistribute

ip ospf apply redistribute direct

ip ospf apply redistribute rip

ip ospf apply redistribute static

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptiondirect Applies only direct redistribution configuration.rip Applies only RIP redistribution configuration.static Applies only static redistribution configuration.



Avaya.com/support


Command: ip ospf area (EthernetInterface Configuration)


ip ospf area (Ethernet Interface Configuration)

Assigns an interface to an OSPF area.

Syntax

default ip ospf [port <port>] area

ip ospf [port <port>] area <A.B.C.D>

no ip ospf [port <port>] area

Default

None

Command mode


Command parameters


<A.B.C.D> Specifies the unique ID of the area to which the interface connects. An area ID of 0.0.0.0indicates the OSPF area backbone and is created automatically by the switch.

port<port>

Selects a port or list of ports.



Avaya.com/support


Command: ip ospf area (VLAN InterfaceConfiguration)


ip ospf area (VLAN Interface Configuration)

Assigns an interface to an OSPF area.

Syntax

default ip ospf area

ip ospf area <A.B.C.D>

no ip ospf area

Default

None

Command mode


Command parameters


<A.B.C.D> Specifies the unique ID of the area to which the interface connects. An area ID of 0.0.0.0indicates the OSPF area backbone and is created automatically by the switch.



Avaya.com/support


Command: ip ospf authentication-key(Ethernet Interface Configuration)


ip ospf authentication-key (Ethernet Interface Configuration)

Configures an OSPF interface authentication password.

Syntax

default ip ospf [port <port>] authentication-key

ip ospf [port <port>] authentication-key <WORD>

no ip ospf [port <port>] authentication-key

Default

None

Command mode


Command parameters


<WORD> Specifies an alphanumeric authentication key for the interface. The authentication keycan be a maximum of 8 characters.

port<port>

Selects a port or list of ports.



Avaya.com/support


Command: ip ospf authentication-key(VLAN Interface Configuration)


ip ospf authentication-key (VLAN Interface Configuration)

Configures an OSPF interface authentication password.

Syntax

default ip ospf authentication-key

ip ospf authentication-key <WORD>

no ip ospf authentication-key

Default

None

Command mode


Command parameters


<WORD> Specifies an alphanumeric authentication key for the interface. The authentication keycan be a maximum of 8 characters.



Avaya.com/support


Command: ip ospf authentication-type(Ethernet Interface Configuration)


ip ospf authentication-type (Ethernet Interface Configuration)

Configures the interface authentication type.

Syntax

default ip ospf [port <port>] authentication-type

ip ospf [port <port>] authentication-type <message-digest | none | simple>

no ip ospf [port <port>] authentication-type

Default

None

Command mode


Command parameters

Parameter Descriptionmessage-digest Spceifies MD5 digest authentication type.none No authentication type is applied to the interface.port <port> Selects a port or list of ports.simple Specifies simple password authentication type.



Avaya.com/support


Command: ip ospf authentication-type(VLAN Interface Configuration)


ip ospf authentication-type (VLAN Interface Configuration)

Configures the interface authentication type.

Syntax

default ip ospf authentication-type

ip ospf authentication-type <message-digest | none | simple>

no ip ospf authentication-type

Default

None

Command mode


Command parameters

Parameter Descriptionmessage-digest Spceifies MD5 digest authentication type.none No authentication type is applied to the interface.simple Specifies simple password authentication type.



Avaya.com/support


Command: ip ospf cost (EthernetInterface Configuration)


ip ospf cost (Ethernet Interface Configuration)

Specifies the cost metric assigned to the interface.

Syntax

default ip ospf [port <port>] cost

ip ospf [port <port>] cost <1-65535>

Default

10

Command mode


Command parameters

Parameter Description<1-65535> Specifies the cost metric.port <port> Selects a port or list of ports.



Avaya.com/support


Command: ip ospf cost (VLAN InterfaceConfiguration)


ip ospf cost (VLAN Interface Configuration)

Specifies the cost metric assigned to the interface.

Syntax

default ip ospf cost

ip ospf cost <1-65535>

Default

10

Command mode


Command parameters

Parameter Description<1-65535> Specifies the cost metric.



Avaya.com/support


Command: ip ospf dead-interval(Ethernet Interface Configuration)


ip ospf dead-interval (Ethernet Interface Configuration)

Specifies the interval of time that a neighbor waits for a hello packet from this interface before the neighbor declares the interfaceto be down.

Syntax

default ip ospf [port <port>] dead-interval

ip ospf [port <port>] dead-interval <1-2147483647>

Default

40

Command mode


Command parameters

Parameter Description<1-2147483647> Specifies the dead interval, in seconds.port <port> Selects a port or list of ports.



Avaya.com/support


Command: ip ospf dead-interval (VLANInterface Configuration)


ip ospf dead-interval (VLAN Interface Configuration)

Specifies the interval of time that a neighbor waits for a hello packet from this interface before the neighbor declares the interfaceto be down.

Syntax

default ip ospf dead-interval

ip ospf dead-interval <1-2147483647>

Default

40

Command mode


Command parameters

Parameter Description<1-2147483647> Specifies the dead interval, in seconds.



Avaya.com/support


Command: ip ospf enable (EthernetInterface Configuration)


ip ospf enable (Ethernet Interface Configuration)

Enables OSPF for the interface.

Syntax

default ip ospf [port <port>] enable

ip ospf [port <port>] enable

no ip ospf [enable]

Default

Disabled

Command mode


Command parameters




Avaya.com/support


Command: ip ospf enable (VLANInterface Configuration)


ip ospf enable (VLAN Interface Configuration)

Enables OSPF for the interface.

Syntax

default ip ospf enable

ip ospf enable

no ip ospf [enable]

Default

Disabled

Command mode




Avaya.com/support


Command: ip ospf hello-interval(Ethernet Interface Configuration)


ip ospf hello-interval (Ethernet Interface Configuration)

Specifies the period of time, in seconds, between the transmission of hello packets from the interface.

Syntax

default ip ospf [port <port>] hello-interval

ip ospf [port <port>] hello-interval <1-65535>

Default

10

Command mode


Command parameters

Parameter Description<1-65535> Specifies the hello interval, in seconds.port <port> Selects a port or list of ports.



Avaya.com/support


Command: ip ospf hello-interval (VLANInterface Configuration)


ip ospf hello-interval (VLAN Interface Configuration)

Specifies the period of time, in seconds, between the transmission of hello packets from the interface.

Syntax

default ip ospf hello-interval

ip ospf hello-interval <1-65535>

Default

10

Command mode


Command parameters

Parameter Description<1-65535> Specifies the hello interval, in seconds.



Avaya.com/support


Command: ip ospf message-digest-key(Ethernet Interface Configuration)


ip ospf message-digest-key (Ethernet Interface Configuration)

Configures the MD5 key for the interface.

Syntax

default ip ospf message-digest-key <1-255>

ip ospf message-digest-key <1-255> md5 <WORD>

no ip ospf message-digest-key <1-255>

Default

None

Command mode


Command parameters

Parameter Description<1-255>md5 <WORD>

Specifies an key index value for the MD5 key being configured, between 1 and 255.The key-value is a string up to 16 characters in length.



Avaya.com/support


Command: ip ospf message-digest-key(VLAN Interface Configuration)


ip ospf message-digest-key (VLAN Interface Configuration)

Configures the MD5 key for the interface.

Syntax

default ip ospf message-digest-key <1-255>

ip ospf message-digest-key <1-255> md5 <WORD>

no ip ospf message-digest-key <1-255>

Default

None

Command mode


Command parameters

Parameter Description<1-255>md5 <WORD>

Specifies an key index value for the MD5 key being configured, between 1 and 255.The key-value is a string up to 16 characters in length.



Avaya.com/support


Command: ip ospf mtu-ignore enable(Ethernet Interface Configuration)


ip ospf mtu-ignore enable (Ethernet Interface Configuration)

Instructs the interface to ignore the packet MTU size specified in database descriptors.

Syntax

default ip ospf [port <port>] mtu-ignore enable

ip ospf [port <port>] mtu-ignore enable

no ip ospf [port <port>] mtu-ignore enable

Default

Enabled

Command mode


Command parameters




Avaya.com/support


Command: ip ospf mtu-ignore enable(VLAN Interface Configuration)


ip ospf mtu-ignore enable (VLAN Interface Configuration)

Instructs the interface to ignore the packet MTU size specified in database descriptors.

Syntax

default ip ospf mtu-ignore enable

ip ospf mtu-ignore enable

no ip ospf mtu-ignore enable

Default

Enabled

Command mode




Avaya.com/support


Command: ip ospf network (EthernetInterface Configuration)


ip ospf network (Ethernet Interface Configuration)

Specifies the OSPF type for the interface.

Syntax

default ip ospf [port <port>] network

ip ospf [port <port>] network <broadcast | passive>

Default

Broadcast

Command mode


Command parameters

Parameter Description<broadcast | passive> Specifies the type.port <port> Selects a port or list of ports.



Avaya.com/support


Command: ip ospf network (VLANInterface Configuration)


ip ospf network (VLAN Interface Configuration)

Specifies the OSPF type for the interface.

Syntax

default ip ospf network

ip ospf network <broadcast | passive>

Default

Broadcast

Command mode


Command parameters

Parameter Description<broadcast | passive> Specifies the type.



Avaya.com/support


Command: ip ospf primary-md5-key(Ethernet Interface Configuration)


ip ospf primary-md5-key (Ethernet Interface Configuration)

Specifies the primary MD5 key value to use for authentication.

Syntax

ip ospf [port <port>] primary-md5-key <1-255>

Default

None

Command mode


Command parameters

Parameter Description<1-255> Specifies the key number.port <port> Selects a port or list of ports.



Avaya.com/support


Command: ip ospf primary-md5-key(VLAN Interface Configuration)


ip ospf primary-md5-key (VLAN Interface Configuration)

Specifies the primary MD5 key value to use for authentication.

Syntax

ip ospf primary-md5-key <1-255>

Default

None

Command mode


Command parameters

Parameter Description<1-255> Specifies the key number.



Avaya.com/support


Command: ip ospf priority (EthernetInterface Configuration)


ip ospf priority (Ethernet Interface Configuration)

Specifies a Designated Router (DR) election priority for the interface.

Syntax

default ip ospf [port <port>] priority

ip ospf [port <port>] priority <0-255>

Default

1

Command mode


Command parameters

Parameter Description<0-255> Specifies the priority value.port <port> Selects a port or list of ports.



Avaya.com/support


Command: ip ospf priority (VLANInterface Configuration)


ip ospf priority (VLAN Interface Configuration)

Specifies a Designated Router (DR) election priority for the interface.

Syntax

default ip ospf priority

ip ospf priority <0-255>

Default

1

Command mode


Command parameters

Parameter Description<0-255> Specifies the priority value.



Avaya.com/support


Command: ip ospf retransmit-interval(Ethernet Interface Configuration)


ip ospf retransmit-interval (Ethernet Interface Configuration)

Specifies the time interval, in seconds, between link state advertisement retransmissions from the interface.

Syntax

default ip ospf [port <port>] retransmit-interval

ip ospf [port <port>] retransmit-interval <1-3600>

no ip ospf [port <port>] retransmit-interval

Default

5

Command mode


Command parameters

Parameter Description<1-3600> Specifies the interval, in seconds.port <port> Selects a port or list of ports.



Avaya.com/support


Command: ip ospf retransmit-interval(VLAN Interface Configuration)


ip ospf retransmit-interval (VLAN Interface Configuration)

Specifies the time interval, in seconds, between link state advertisement retransmissions from the interface.

Syntax

default ip ospf retransmit-interval

ip ospf retransmit-interval <1-3600>

no ip ospf retransmit-interval

Default

5

Command mode


Command parameters

Parameter Description<1-3600> Specifies the interval, in seconds.



Avaya.com/support


Command: ip ospf transit-delay(Ethernet Interface Configuration)


ip ospf transit-delay (Ethernet Interface Configuration)

Specifies the estimated number of seconds for the interface to transmit link state advertisements.

Syntax

default ip ospf [port <port>] transit-delay

ip ospf [port <port>] transit-delay <1-3600>

no ip ospf [port <port>] transit-delay

Default

1

Command mode


Command parameters

Parameter Description<1-3600> Specifies the delay, in seconds.port <port> Selects a port or list of ports.



Avaya.com/support


Command: ip ospf transit-delay (VLANInterface Configuration)


ip ospf transit-delay (VLAN Interface Configuration)

Specifies the estimated number of seconds for the interface to transmit link state advertisements.

Syntax

default ip ospf transit-delay

ip ospf transit-delay <1-3600>

no ip ospf transit-delay

Default

1

Command mode


Command parameters

Parameter Description<1-3600> Specifies the delay, in seconds.



Avaya.com/support


Command: ip prefix-list


ip prefix-list

Adds or modifies a prefix from a prefix list.

Syntax

ip prefix-list <WORD> <A.B.C.D/0-32> [ge <0-32>] [le <0-32>]

ip prefix-list <WORD> name <WORD>

no ip prefix-list <WORD> [<A.B.C.D/0-32>]

Default

None

Command mode


Command parameters

Parameter Description<A.B.C.D/0-32>

Specifies the IP prefix and mask bits.

<WORD> Identifies the name or renames the prefix list.

ge <0-32> Specifies the starting point within the mask length. Specify the lower bound andhigher bound mask lengths together to define a range of networks.

le <0-32> Specifies the ending point within the mask length. Specify the lower bound and higherbound mask lengths together to define a range of networks.



Avaya.com/support


Command: ip rip advertise-when-downenable (Ethernet InterfaceConfiguration)


ip rip advertise-when-down enable (Ethernet InterfaceConfiguration)

Enables RIP advertisements for an interface even when the link to the network fails. The switch continues to advertise the subneteven if that particular network is no longer connected (no link in the enabled VLAN). This feature only functions on enabledinterfaces.

Syntax

default ip rip [port <port>] advertise-when-down enable

ip rip [port <port>] advertise-when-down enable

no ip rip [port <port>] advertise-when-down enable

Default

Disabled

Command mode


Command parameters

Parameter Descriptionport <port> Specifies a port or port list.



Avaya.com/support


Command: ip rip advertise-when-downenable (VLAN Interface Configuration)


ip rip advertise-when-down enable (VLAN Interface Configuration)

Enables RIP advertisements for an interface even when the link to the network fails. The switch continues to advertise the subneteven if that particular network is no longer connected (no link in the enabled VLAN). This feature only functions on enabledinterfaces.

Syntax

default ip rip advertise-when-down enable

ip rip advertise-when-down enable

no ip rip advertise-when-down enable

Default

Disabled

Command mode




Avaya.com/support


Command: ip rip auto-aggregationenable (Ethernet InterfaceConfiguration)


ip rip auto-aggregation enable (Ethernet Interface Configuration)

Enables automatic route aggregation on the interface. When automatic route aggregation is enabled, the switch automaticallyaggregates routes to their natural mask when an interface in a different class network advertises them. You can enable automaticroute aggregation only in RIP2 mode or RIP1 compatibility mode.

Syntax

default ip rip [port <port>] auto-aggregation enable

ip rip [port <port>] auto-aggregation enable

no ip rip [port <port>] auto-aggregation enable

Default

Disabled

Command mode


Command parameters




Avaya.com/support


Command: ip rip auto-aggregationenable (VLAN Interface Configuration)


ip rip auto-aggregation enable (VLAN Interface Configuration)

Enables automatic route aggregation on the interface. When automatic route aggregation is enabled, the switch automaticallyaggregates routes to their natural mask when an interface in a different class network advertises them. You can enable automaticroute aggregation only in RIP2 mode or RIP1 compatibility mode.

Syntax

default ip rip auto-aggregation enable

ip rip auto-aggregation enable

no ip rip auto-aggregation enable

Default

Disabled

Command mode




Avaya.com/support


Command: ip rip cost (EthernetInterface Configuration)


ip rip cost (Ethernet Interface Configuration)

Specifies the RIP cost (metric) for the selected interface.

Syntax

default ip rip [port <port>] cost

ip rip [port <port>] cost <1-15>

Default

1

Command mode


Command parameters

Parameter Description<1-15> Specifies the metric value.port <port> Specifies a port or port list.



Avaya.com/support


Command: ip rip cost (VLAN InterfaceConfiguration)


ip rip cost (VLAN Interface Configuration)

Specifies the RIP cost (metric) for the selected interface.

Syntax

default ip rip cost

ip rip cost <1-15>

Default

1

Command mode


Command parameters

Parameter Description<1-15> Specifies the metric value.



Avaya.com/support


Command: ip rip default-listen enable(Ethernet Interface Configuration)


ip rip default-listen enable (Ethernet Interface Configuration)

Enables the interface to accept default routes learned through RIP updates.

Syntax

default ip rip [port <port>] default-listen enable

ip rip [port <port>] default-listen enable

no ip rip [port <port>] default-listen enable

Default

Disabled

Command mode


Command parameters




Avaya.com/support


Command: ip rip default-listen enable(VLAN Interface Configuration)


ip rip default-listen enable (VLAN Interface Configuration)

Enables the interface to accept default routes learned through RIP updates.

Syntax

default ip rip default-listen enable

ip rip default-listen enable

no ip rip default-listen enable

Default

Disabled

Command mode




Avaya.com/support


Command: ip rip default-supply enable(Ethernet Interface Configuration)


ip rip default-supply enable (Ethernet Interface Configuration)

Enables the interface to send default route information in RIP updates.

Syntax

default ip rip [port <port>] default-supply enable

ip rip [port <port>] default-supply enable

no ip rip [port <port>] default-supply enable

Default

Disabled

Command mode


Command parameters




Avaya.com/support


Command: ip rip default-supply enable(VLAN Interface Configuration)


ip rip default-supply enable (VLAN Interface Configuration)

Enables the interface to send default route information in RIP updates.

Syntax

default ip rip default-supply enable

ip rip default-supply enable

no ip rip default-supply enable

Default

Disabled

Command mode




Avaya.com/support


Command: ip rip enable (EthernetInterface Configuration)


ip rip enable (Ethernet Interface Configuration)

Enables RIP on the IP interface.

Syntax

default ip rip [port <port>] [enable]

ip rip [port <port>] enable

no ip rip [port <port>] [enable]

Default

Disabled

Command mode


Command parameters




Avaya.com/support


Command: ip rip enable (VLANInterface Configuration)


ip rip enable (VLAN Interface Configuration)

Enables RIP on the IP interface.

Syntax

default ip rip [enable]

ip rip enable

no ip rip [enable]

Default

Disabled

Command mode




Avaya.com/support


Command: ip rip holddown (EthernetInterface Configuration)


ip rip holddown (Ethernet Interface Configuration)

Specifies the length of time (in seconds) that the interface RIP maintains a route in the garbage list after determining that route isunreachable.

Syntax

default ip rip [port <port>] holddown

ip rip [port <port>] holddown <0-360 | global>

Default

120

Command mode


Command parameters


<0-360 |global>

Specifies a holddown period or uses the global timer. During the holddown period, RIPcontinues to advertise the garbage route with a metric of infinity (16). If a valid updatefor a garbage route is received within the holddown period, the switch adds the routeback into the routing table. If no update is received, the switch deletes the garbage listentry. If the interface holddown timer is configured, this setting overrides the globalholddown timer and does not change if the global holddown timer is modified.

port<port>

Specifies a port or port list.



Avaya.com/support


Command: ip rip holddown (VLANInterface Configuration)


ip rip holddown (VLAN Interface Configuration)

Specifies the length of time (in seconds) that the interface RIP maintains a route in the garbage list after determining that route isunreachable.

Syntax

default ip rip holddown

ip rip holddown <0-360 | global>

Default

120

Command mode


Command parameters


<0-360 |global>

Specifies a holddown period or uses the global timer. During the holddown period, RIPcontinues to advertise the garbage route with a metric of infinity (16). If a valid updatefor a garbage route is received within the holddown period, the switch adds the routeback into the routing table. If no update is received, the switch deletes the garbage listentry. If the interface holddown timer is configured, this setting overrides the globalholddown timer and does not change if the global holddown timer is modified.



Avaya.com/support


Command: ip rip in-policy (EthernetInterface Configuration)


ip rip in-policy (Ethernet Interface Configuration)

Specifies a RIP in-policy to use for the selected interface.

Syntax

default ip rip [port <port>] in-policy

ip rip [port <port>] in-policy <WORD>

no ip rip [port <port>] in-policy

Default

None

Command mode


Command parameters

Parameter Description<WORD> Specifies a policy name.port <port> Specifies a port or port list.



Avaya.com/support


Command: ip rip in-policy (VLANInterface Configuration)


ip rip in-policy (VLAN Interface Configuration)

Specifies a RIP in-policy to use for the selected interface.

Syntax

default ip rip in-policy

ip rip in-policy <WORD>

no ip rip in-policy

Default

None

Command mode


Command parameters

Parameter Description<WORD> Specifies a policy name.



Avaya.com/support


Command: ip rip listen enable (EthernetInterface Configuration)


ip rip listen enable (Ethernet Interface Configuration)

Enables the selected interface to listen for RIP advertisements.

Syntax

default ip rip [port <port>] listen enable

ip rip [port <port>] listen enable

no ip rip [port <port>] listen enable

Default

Enabled

Command mode


Command parameters




Avaya.com/support


Command: ip rip listen enable (VLANInterface Configuration)


ip rip listen enable (VLAN Interface Configuration)

Enables the selected interface to listen for RIP advertisements.

Syntax

default ip rip listen enable

ip rip listen enable

no ip rip listen enable

Default

Enabled

Command mode




Avaya.com/support


Command: ip rip out-policy (EthernetInterface Configuration)


ip rip out-policy (Ethernet Interface Configuration)

Specifies a RIP out-policy to use for the selected interface.

Syntax

default ip rip [port <port>] out-policy

ip rip [port <port>] out-policy <WORD>

no ip rip [port <port>] out-policy

Default

None

Command mode


Command parameters

Parameter Description<WORD> Specifies a policy name.port <port> Specifies a port or port list.



Avaya.com/support


Command: ip rip out-policy (VLANInterface Configuration)


ip rip out-policy (VLAN Interface Configuration)

Specifies a RIP out-policy to use for the selected interface.

Syntax

default ip rip out-policy

ip rip out-policy <WORD>

no ip rip out-policy

Default

None

Command mode


Command parameters

Parameter Description<WORD> Specifies a policy name.



Avaya.com/support


Command: ip rip poison enable(Ethernet Interface Configuration)


ip rip poison enable (Ethernet Interface Configuration)

Specifies whether RIP routes on the interface learned from a neighbor are reversed back to the neighbor.

Syntax

default ip rip [port <port>] poison enable

ip rip [port <port>] poison enable

no ip rip [port <port>] poison enable

Default

Disabled

Command mode


Command parameters




Avaya.com/support


Command: ip rip poison enable (VLANInterface Configuration)


ip rip poison enable (VLAN Interface Configuration)

Specifies whether RIP routes on the interface learned from a neighbor are reversed back to the neighbor.

Syntax

default ip rip poison enable

ip rip poison enable

no ip rip poison enable

Default

Disabled

Command mode




Avaya.com/support


Command: ip rip proxy-announceenable (Ethernet InterfaceConfiguration)


ip rip proxy-announce enable (Ethernet Interface Configuration)

Enables proxy announcements for the RIP interface. When you enable proxy announcements, the source of a route and the nexthop are treated equally when the switch processes received updates. The next hop is advertised as the source, not the switch.

Syntax

default ip rip [port <port>] proxy-announce enable

ip rip [port <port>] proxy-announce enable

no ip rip [port <port>] proxy-announce enable

Default

Disabled

Command mode


Command parameters




Avaya.com/support


Command: ip rip proxy-announceenable (VLAN Interface Configuration)


ip rip proxy-announce enable (VLAN Interface Configuration)

Enables proxy announcements for the RIP interface. When you enable proxy announcements, the source of a route and the nexthop are treated equally when the switch processes received updates. The next hop is advertised as the source, not the switch.

Syntax

default ip rip proxy-announce enable

ip rip proxy-announce enable

no ip rip proxy-announce enable

Default

Disabled

Command mode




Avaya.com/support


Command: ip rip receive (EthernetInterface Configuration)


ip rip receive (Ethernet Interface Configuration)

Specifies the RIP version to accept for route updates received on the selected interface.

Syntax

default ip rip [port <port>] receive version

ip rip receive [port <port>] version {rip1 | rip1orrip2 | rip2}

Default

rip1orrip2

Command mode


Command parameters

Parameter Descriptionport <port> Specifies a port or port list.rip1 Accepts RIP version 1.rip1orrip2 Accepts RIP version 1 or RIP version 2.rip2 Accepts RIP version 2.



Avaya.com/support


Command: ip rip receive (VLANInterface Configuration)


ip rip receive (VLAN Interface Configuration)

Specifies the RIP version to accept for route updates received on the selected interface.

Syntax

default ip rip receive version

ip rip receive version {rip1 | rip1orrip2 | rip2}

Default

rip1orrip2

Command mode


Command parameters

Parameter Descriptionrip1 Accepts RIP version 1.rip1orrip2 Accepts RIP version 1 or RIP version 2.rip2 Accepts RIP version 2.



Avaya.com/support


Command: ip rip send (EthernetInterface Configuration)


ip rip send (Ethernet Interface Configuration)

Specifies the RIP version to use for sending route updates from the selected interface.

Syntax

default ip rip [port <port>] send version

ip rip [port <port>] send version {notsend | rip1 | rip1orrip2 | rip2}

Default

rip1orrip2

Command mode


Command parameters

Parameter Descriptionnotsend The interface does not send updates.port <port> Specifies a port or port list.rip1 Sends RIP version 1.rip1orrip2 Sends RIP version 1 or RIP version 2.rip2 Sends RIP version 2.



Avaya.com/support


Command: ip rip send (VLAN InterfaceConfiguration)


ip rip send (VLAN Interface Configuration)

Specifies the RIP version to use for sending route updates from the selected interface.

Syntax

default ip rip send version

ip rip send version {notsend | rip1 | rip1orrip2 | rip2}

Default

rip1orrip2

Command mode


Command parameters

Parameter Descriptionnotsend The interface does not send updates.rip1 Sends RIP version 1.rip1orrip2 Sends RIP version 1 or RIP version 2.rip2 Sends RIP version 2.



Avaya.com/support


Command: ip rip supply enable(Ethernet Interface Configuration)


ip rip supply enable (Ethernet Interface Configuration)

Enables RIP router advertisements for the selected interface.

Syntax

default ip rip [port <port>] supply enable

ip rip [port <port>] supply enable

no ip rip [port <port>] supply enable

Default

Enabled

Command mode


Command parameters




Avaya.com/support


Command: ip rip supply enable (VLANInterface Configuration)


ip rip supply enable (VLAN Interface Configuration)

Enables RIP router advertisements for the selected interface.

Syntax

default ip rip supply enable

ip rip supply enable

no ip rip supply enable

Default

Enabled

Command mode




Avaya.com/support


Command: ip rip timeout (EthernetInterface Configuration)


ip rip timeout (Ethernet Interface Configuration)

Specifies the RIP timeout (in seconds) for this interface. If a RIP interface does not receive an update from another RIP–enabledswitch or router within the configured timeout period, the RIP interface moves the routes advertised by the nonupdating switch orrouter to the garbage list. The timeout interval must be greater than the update timer.

Syntax

default ip rip [port <port>] timeout

ip rip [port <port>] timeout <15-259200 | global>

Default

180

Command mode


Command parameters

Parameter Description<15-259200 |global>

Specifies a timeout interval or uses the global value. The interface RIP timeout settingoverrides the global RIP timeout setting and the interface RIP timeout value does notchange if you change the global RIP timeout value.

port<port>

Specifies a port or port list.



Avaya.com/support


Command: ip rip timeout (VLANInterface Configuration)


ip rip timeout (VLAN Interface Configuration)

Specifies the RIP timeout (in seconds) for this interface. If a RIP interface does not receive an update from another RIP–enabledswitch or router within the configured timeout period, the RIP interface moves the routes advertised by the nonupdating switch orrouter to the garbage list. The timeout interval must be greater than the update timer.

Syntax

default ip rip timeout

ip rip timeout <15-259200 | global>

Default

180

Command mode


Command parameters

Parameter Description<15-259200 |global>

Specifies a timeout interval or uses the global value. The interface RIP timeout settingoverrides the global RIP timeout setting and the interface RIP timeout value does notchange if you change the global RIP timeout value.



Avaya.com/support


Command: ip rip triggered enable(Ethernet Interface Configuration)


ip rip triggered enable (Ethernet Interface Configuration)

Enables automatic triggered updates for the selected RIP interface.

Syntax

default ip rip [port <port>] triggered enable

ip rip [port <port>] triggered enable

no ip rip [port <port>] triggered enable

Default

Disabled

Command mode


Command parameters




Avaya.com/support


Command: ip rip triggered enable(VLAN Interface Configuration)


ip rip triggered enable (VLAN Interface Configuration)

Enables automatic triggered updates for the selected RIP interface.

Syntax

default ip rip triggered enable

ip rip triggered enable

no ip rip triggered enable

Default

Disabled

Command mode




Avaya.com/support


Command: ip route


ip route

Creates a static route.

Syntax

ip route {A.B.C.D} {A.B.C.D} {A.B.C.D} <1-65535>

ip route {A.B.C.D} {A.B.C.D} {A.B.C.D} disable

ip route {A.B.C.D} {A.B.C.D} {A.B.C.D} enable

ip route {A.B.C.D} {A.B.C.D} {A.B.C.D} weight <1-65535>

no ip route {A.B.C.D} {A.B.C.D} {A.B.C.D}

Default

None

Command mode


Command parameters

Parameter Description{A.B.C.D}{A.B.C.D}{A.B.C.D}

The first and second <A.B.C.D> specify the IP address and mask for the routedestination. 255.255.255.255 is the black hole route. The third <A.B.C.D> specifiesthe next-hop address.

<1-65535> Specifies the cost for a newly created static route.disable Disables the route.enable Enables the route.weight <1-65535>

Changes the weight (cost) of an existing static route.



Avaya.com/support


Command: ip routing (GlobalConfiguration)


ip routing (Global Configuration)

Enables global routing.

Syntax

ip routing

ip routing force

no ip routing

Default

None

Command mode


Command parameters

Parameter Descriptionforce Does not ask for confirmation.



Avaya.com/support


Command: ip routing (VLAN InterfaceConfiguration)


ip routing (VLAN Interface Configuration)

Enables Layer 3 routing on a VLAN.

Syntax

Default

None

Command mode


Command parameters

Parameter Descriptionforce Do not ask for confirmation.



Avaya.com/support


Command: ip source-interface


ip source-interface

Assigns or removes the CLIP as the source IP address for the selected applications.

Syntax

default ip source-interface {all | radius | snmp-traps | ssh | syslog | tacacs | telnet}

ip source-interface {all | radius | snmp-traps | ssh | syslog | tacacs | telnet} loopback

<1–16>

no ip source-interface {all | radius | snmp-traps | ssh | syslog | tacacs | telnet}

Default

Removed

Command mode


Command parameters

Parameter Description{all | radius | snmp-traps | ssh |syslog | tacacs | telnet}

Specifies the application for which to assign theCLIP as the source IP address.

loopback <1–16> Specifies the loopback interface identifier.



Avaya.com/support


Command: ipv6


ipv6

Configures IPv6 globally.

Syntax

default ipv6

default ipv6 enable

default ipv6 forwarding

default ipv6 hop-limit

default ipv6 icmp block-multicast-replies

default ipv6 icmp error-interval

default ipv6 icmp error-quota

default ipv6 icmp unreach-msg

ipv6 enable

ipv6 forwarding

ipv6 hop-limit <0-255>

ipv6 icmp block-multicast-replies

ipv6 icmp error-interval <0-2147483647>

ipv6 icmp error-quota <0-2000000>

ipv6 icmp unreach-msg

no ipv6

no ipv6 enable

no ipv6 forwarding

no ipv6 icmp block-multicast-replies

no ipv6 icmp unreach-msg

Default

None

Command mode


Command parameters

Parameter Descriptionenable Enables the IPv6 global admin status. The default is disabled.forwarding Enables global IPv6 forwarding. The default is disabled.hop-limit <0-255> Inserts a value into the hop-limit field of IPv6 header. The default is 30.icmp block-multicast-replies

Enables IPv6 ICMP block-multicast-replies. The default is disabled. You canconfigure multiple ICMP parameters in one command string.

icmp error-interval <0-2147483647>

Sets IPv6 ICMP error-interval. The default is 1000. You can configuremultiple ICMP parameters in one command string.

icmp error-quota<0-2000000>

Sets IPv6 ICMP error-quota. The default is 50. You can configure multipleICMP parameters in one command string.

icmp unreach-msg Enables IPv6 ICMP unreach-msg. The default is disabled. You can configuremultiple ICMP parameters in one command string.



Avaya.com/support


Command: ipv6 address


ipv6 address

Configures the IPV6 address/prefix_length for a stack, switch, or unit.

Syntax

default ipv6 address [ stack | switch | unit <1-8>]

ipv6 address [ stack | switch | unit <1-8>] <WORD>

no ipv6 address [ stack | switch | unit <1-8>]

Default

None

Command mode


Command parameters

Parameter Description<WORD> Specifies the IPv6 address/prefix.stack | switch | unit <1-8> Configures the address for a stack, switch, or particular unit.



Avaya.com/support


Command: ipv6 autoconfig


ipv6 autoconfig

Configures IPv6 autoconfiguration.

Syntax

default ipv6 autoconfig

ipv6 autoconfig

no ipv6 autoconfig

Default

None

Command mode




Avaya.com/support


Command: ipv6 default-gateway


ipv6 default-gateway

Configures the IPv6 default gateway.

Syntax

default ipv6 default-gateway

ipv6 default-gateway <WORD>

no ipv6 default-gateway

Default

None

Command mode


Command parameters

Parameter Description<WORD> Specifies the IPv6 address.



Avaya.com/support


Command: ipv6 dhcp-relay (GlobalConfiguration)


ipv6 dhcp-relay (Global Configuration)

Configures IPv6 DHCP relay globally.

Syntax

default ipv6 dhcp-relay fwd-path <WORD> <WORD> [enable]

ipv6 dhcp-relay fwd-path <WORD> <WORD> [enable]

no ipv6 dhcp-relay fwd-path <WORD> <WORD> [enable]

Default

None

Command mode


Command parameters

Parameter Description<WORD> <WORD> Specifies the agent and the server address.



Avaya.com/support


Command: ipv6 dhcp-relay (VLANInterface Configuration)


ipv6 dhcp-relay (VLAN Interface Configuration)

Configure IPv6 DHCP relay on a VLAN.

Syntax

ipv6 dhcp-relay [fwd-path <WORD> [enable]][max-hop <1-32>][remote-id]

Default

None

Command mode


Command parameters

Parameter Descriptionfwd-path <server-ip> [enable] Create a forward path and enable forward path on VLANmax-hop <1-32? Set max hop countremote-id Enable remote-id



Avaya.com/support


Command: ipv6 icmp addr-unreach


ipv6 icmp addr-unreach

Enable IPv6 Internet Control Message Protocol (ICMP) address unreachable.

Syntax

default ipv6 icmp addr-unreach icmp

ipv6 icmp addr-unreach icmp

no ipv6 icmp addr-unreach icmp

Default

None

Command mode


Command parameters

Parameter Descriptionicmp Enables IPv6 ICMP unreachable message.



Avaya.com/support


Command: ipv6 icmp block-multicast-replies


ipv6 icmp block-multicast-replies

Enable IPv6 Internet Control Message Protocol (ICMP) block-multicast-replies.

Syntax

ipv6 icmp block-multicast-replies icmp

no ipv6 icmp block-multicast-replies icmp

default ipv6 icmp block-multicast-replies icmp

Default

None

Command mode


Command parameters

Parameter Descriptionicmp Enables IPv6 ICMP block-multicast-replies.



Avaya.com/support


Command: ipv6 icmp error-interval


ipv6 icmp error-interval

Enable IPv6 Internet Control Message Protocol (ICMP) error-interval.

Syntax

ipv6 icmp error-interval <0-2147483647>

Default

None

Command mode


Command parameters

Parameter Description<0-2147483647> Enables IPv6 ICMP error-interval.



Avaya.com/support


Command: ipv6 icmp error-quota


ipv6 icmp error-quota

Enable IPv6 Internet Control Message Protocol (ICMP) error-quota.

Syntax

ipv6 icmp error-quota

Default

None

Command mode


Command parameters

Parameter DescriptionNone Enables IPv6 ICMP error-quota.



Avaya.com/support


Command: ipv6 icmp port-unreach


ipv6 icmp port-unreach

Enable IPv6 Internet Control Message Protocol (ICMP) port-unreach.

Syntax

default ipv6 icmp port-unreach icmp

ipv6 icmp port-unreach icmp

no ipv6 icmp port-unreach icmp

Default

None

Command mode


Command parameters

Parameter Descriptionicmp Enables IPv6 ICMP port unreachable message.



Avaya.com/support


Command: ipv6 icmp unreach-msg



Enable IPv6 Internet Control Message Protocol (ICMP) unreach-msg.

Syntax


Default

None

Command mode


Command parameters

Parameter DescriptionNone Enables IPv6 ICMP unreachable message.



Avaya.com/support


Command: ipv6 interface (LoopbackInterface Configuration)


ipv6 interface (Loopback Interface Configuration)

Creates and configures a Loopback IPv6 interface.

Syntax

default ipv6 interface [enable]

ipv6 interface [address <WORD>][enable]

no ipv6 interface [address <WORD>][enable]

Default

None

Command mode


Command parameters

Parameter Descriptionaddress <WORD> Specifies the IPv6 address.enable Enables the address.



Avaya.com/support


Command: ipv6 interface (VLANInterface Configuration)


ipv6 interface (VLAN Interface Configuration)

Creates and configures a VLAN IPv6 interface.

Syntax

default ipv6 interface [all][enable][link-local][mtu] [reachable-time] [retransmit-timer]

ipv6 interface [address <WORD>][enable][link-local][mtu <bytes>] [name <name>] [reachable-

time <ms>] [retransmit-timer <ms>]

no ipv6 interface[address <WORD>][all][enable]

Default

None

Command mode


Command parameters

Parameter Descriptionaddress<ipv6address>

Specifies the IPv6 address to assign to the interface.

all Adminstratively disables the management VLAN IPv6 interface and deletes the IPv6address previously assigned to the interface.

enable Enables interface admin status.link-local<WORD>

Specifies an IPv6 address identifier for the local link, with a maximum of 19characters.

mtu <1280-9216>

Configures the maximum transmission unit for the interface. The default value is1500.

name<WORD>

Specifies a unique alphanumeric name for the interface, with a maximum of 255characters.

reachable-time <1-3600000>

Configures the time, in milliseconds, that an IPv6 neighbor is considered reachableafter receiving a reachability confirmation. Range is 1-3600000. The default value is30000.

retransmit-timer <0-3600000>

Configures the time, in milliseconds, between retransmissions of neighbor solicitationmessages to a neighbor when resolving the address or when probing the reachabilityof an IPv6 neighbor. The default value is 1000.



Command: ipv6 mgmt address


ipv6 mgmt address

Configures the switch or stack management IPv6 address.

Syntax

default ipv6 mgmt address

no ipv6 mgmt address [stack | switch | unit <1-8> ]

Default

None

Command mode


Command parameters

Parameter Description[stack | switch |unit<1-8>]

Specifies a management IPv6 address for an individual switch, unit,or the stack.

<WORD> Specifies the management address.



Avaya.com/support


Command: ipv6 mgmt default-gateway


ipv6 mgmt default-gateway

Specifies the management default gateway.

Syntax

default ip mgmt default-gateway

ip mgmt default-gateway <WORD>

no ip mgmt default-gateway

Default

None

Command mode


Command parameters




Avaya.com/support


Command: ipv6 mgmt interface


ipv6 mgmt interface

Enables the management interface.

Syntax

default ipv6 mgmt interface [process-redirect]

ipv6 mgmt interface [process-redirect]

no ipv6 mgmt interface [process-redirect]

Default

None

Command mode




Avaya.com/support


Command: ipv6 nd prefix


ipv6 nd prefix

Configure neighbor discovery prefix parameters

Syntax

default ipv6 nd prefix <WORD> { [no-advertise] | [preferred-life] | [valid-life]

ipv6 nd prefix <WORD> {[infinite] | [no-advertise] | [preferred-life <0-3600000>] | [valid-

life <0-3600000>]

no ipv6 nd prefix <WORD> no-advertise

Default

None

Command mode


Command parameters

Parameter Description<WORD> Specifies the IPv6 address and prefix lengthinfinite If configured, the prefix does not expire. Default value is false.no-advertise

Removes entry from neighbor advertisement.

preferred-life <0-3600000>

Configures the number of seconds that the prefix can accept and use new connections.Default is 604800.

valid-life<0-3600000>

Specifies the number of seconds that the prefix advertised in the neighboradvertisement is valid. During the valid lifetime, existing connects can be used, newconnections cannot be opened. Default is 2592000.



Avaya.com/support


Command: ipv6 nd prefix-interface


ipv6 nd prefix-interface

Configure neighbor discovery prefixes on a VLAN.

Syntax

default ipv6 nd prefix-interface <WORD> [no-advertise]

ipv6 nd prefix-interface <WORD> [eui <1-3> ] [no-advertise] | [no-autoconfig] | [no-onlink]

no ipv6 nd prefix-interface <WORD> [no-advertise]

Default

None

Command mode


Command parameters

Parameter Description<WORD> Specifies the IPv6 address and prefix lengtheui 1 Specifies the Extended Unique Identifier (EUI) is not used. Default value.eui 2 Specifies EUI is used without U/L.eui 3 Specifies EUI is used without U/L.no-advertise Disables IPv6 nd prefix-interface advertise.no-autoconfig Disables IPv6 nd prefix-interface autoconfig.no-onlink Disables IPv6 nd prefix-interface onlink.



Avaya.com/support


Command: ipv6 nd (VLAN InterfaceConfiguration)


ipv6 nd (VLAN Interface Configuration)

Configure neighbor discovery parameters on a VLAN.

Syntax

default ipv6 nd [dad-ns][hop-limit][managed-config-flag][other-config-flag][ra-

lifetime][rtr-advert-max-interval ][rtr-advert-min-interval][send-ra]

ipv6 nd [dad-ns <0-600>][hop-limit <1-255>][managed-config-flag][other-config-flag][ra-

lifetime <0-9000>][rtr-advert-max-interval <4-1000>][rtr-advert-min-interval <3-

1350>][send-ra]

no ipv6 nd [managed-config-flag][other-config-flag][send-ra]

Default

None

Command mode


Command parameters

Parameter Descriptiondad-ns <0-600>

Configure the number of neighbor solicitation packets sent during duplicate addressdetection.

hop-limit <1-255>

Configure number of hops before packets are dropped.

managed-config-flag

Enables M-bit (managed address configuration) on the router. Use the no operatorto remove this option. Default is false.

other-config-flag

Enables the O-bit (other stateful configuration) in the router advertisement(autoconfigures received information without addresses). Use the no operator toremove this option. Default is false.

ra-lifetime<0-9000>

Configures the router lifetime included in router advertisement. Other devices usethis information to determine if they can reach the router. Default is 1800.

rtr-advert-max-interval<4-1000>

Configures the maximum time allowed between sending unsolicited multicast routeradvertisements. Default is 600.

rtr-advert-min-interval<3-1350>

Configures the minimum time allowed (in seconds) between sending unsolicitedmulticast router advertisements from the interface. Default is 200.

send-ra Enables or disables periodic router advertisement messages. Use the no operatorto remove this option. Default is true.



Avaya.com/support


Command: ipv6 neighbor


ipv6 neighbor

Configures the IPv6 neighbor cache.

Syntax

ipv6 neighbor <WORD> port <port> mac <H.H.H> [vlan <1-4094>]

no ipv6 neighbor <WORD>

Default

None

Command mode


Command parameters

Parameter Description<WORD> Specifies the IPv6 address.mac <H.H.H> Specififes the MAC address of the IPv6 neighbor.port <port> Specifies a port.vlan <1-4094> Specifies a VLAN ID.



Avaya.com/support


Command: ipv6 route


ipv6 route

Creates and configures an IPv6 static route.

Syntax

default ipv6 route <WORD> [cost] [enable] [mgmt] [next-hop <WORD>] [preference] [tunnel <1-

2147483647>] [vlan <1-4094>]

ipv6 route <WORD> cost <1-65535> [enable]

ipv6 route <WORD> mgmt [enable]

ipv6 route <WORD> next-hop <WORD> [enable]

ipv6 route <WORD> preference <1-255> [enable]

ipv6 route <WORD> tunnel <1-2147483647> [enable]

ipv6 route <WORD> vlan <1-4094> [enable]

no ipv6 route <WORD> mgmt [enable]

no ipv6 route <WORD> next-hop <WORD> [enable]

no ipv6 route <WORD> tunnel <1-2147483647 [enable]

no ipv6 route <WORD> vlan <1-4094> [enable]

Default

None

Command mode


Command parameters


cost <1-65535> Specifies the route cost or distance ratio to reach the destination for thisnode. The default is 1.

enable Enables the route.mgmt Designates the route for out-of-band management.next-hop <WORD> Configures the next-hop for the route.preference<1-255>

Specifies the route preference of the destination IPv6 address. The default is5.

tunnel <1-2147483647>

Specifies a tunnel ID.

vlan <1-4094> Specifies a VLAN ID.



Avaya.com/support


Command: ipv6 tunnel


ipv6 tunnel

Configures IPv6 tunnels.

Syntax

default ipv6 tunnel <1-2147483647> [hop-limit]

ipv6 tunnel <1-2147483647> hop-limit <0-255>

ipv6 tunnel <1-2147483647> source {A.B.C.D} address <WORD> destination {A.B.C.D}

no ipv6 tunnel <1-2147483647>

Default

None

Command mode


Command parameters

Parameter Description<1-2147483647> Specifies a tunnel ID.address <WORD> Specifies the IPv6 address and length.destination{A.B.C.D}

Configures the address of the remote endpoint of the tunnel.

hop-limit <0-255> Configures the maximum number of hops in the tunnel. The default is30.

source {A.B.C.D} Configures the address of the local endpoint of the tunnel.



Avaya.com/support


Command: ip verify source


ip verify source

Enables IP Source Guard to add a higher level of security to the desired port by preventing IP spoofing.

Syntax

default ip verify source [interface <Ethernet | WORD> ]

ip verify source

ip verify source interface <Ethernet | WORD>

no ip verify source [interface <Ethernet | WORD> ]

Default

None

Command mode


Command parameters

Parameter Description<WORD> Specifies a port list.Ethernet Selects Ethernet interfaces.



Avaya.com/support


Command: ip vrrp


ip vrrp

Changes VR settings or associate addresses.

Syntax

default ip vrrp <1-255> {[action ] [adver-int] [backup-master enable] [critical-ip enable]

[critical-ip-addr] [enable] [fast-adv enable] [fast-adv-int] [holddown-timer] [priority]}

ip vrrp <1-255> {[action <none | preempt>] [adver-int <1-255>] [backup-master enable]

[critical-ip enable] [critical-ip-addr <A.B.C.D>] [enable] [fast-adv enable] [fast-adv-int

<200-1000>] [holddown-timer <0-21600>] [priority <1-255>]}

no ip vrrp <1-255> { [backup-master enable] [critical-ip enable] [enable] [fast-adv

enable]}

Default

None

Command mode


Command parameters

Parameter Description<1-255> Specify the virtual router ID to configure.action {none |preempt}

Specify the holddown action. Enter none for no action, Enter preempt tocancel the holddown timer.

adver-int <1-255> Specifes the advertisement interval in seconds.badkup-masterenable

Enable the backup master functionality.

critical-ip enable Configure the status of the VRRP critical IP functionality.critical-ip-addr<A.B.C.D>

Set the critical IP address on the router.

enable Enable the VR.fast-adv enable Enable the VRRP fast advertisement functionality.fast-adv-int <200-1000>

Specify the fast advertisement interval in milliseconds. Value between 200and 1000.

holddown-timer <0-21600>

Specify the holddown timer value. Value in seconds between 1 and 21600.

priority <1-255> Specify the priority value for the virtual router ID.



Avaya.com/support


Command: ip vrrp address


ip vrrp address

Associate an address with a VR or change associated address

Syntax

default ip vrrp address <1-255> [<A.B.C.D>]

ip vrrp address <1-255> <A.B.C.D>

no ip vrrp address <1-255> [<A.B.C.D>]

Default

None

Command mode


Command parameters

Parameter Description<1-255> Specify the virtual router ID.<A.B.C.D> Specifies the IP address associated with the virtual router.



Avaya.com/support


Command: i-sid


i-sid

Configures the UNI.

Syntax

default i-sid <1-16777214> [port <port>] [vlan <1-4094>]

default i-sid <1-16777214> [vlan <1-4094> [port <port>]]

i-sid <1-16777214> [port <port> | <smlt-peer>] [vlan <1-4094>]

i-sid <1-16777214> vlan <1-4094> [port <port>]

no i-sid <1-16777214> port [<port> | <smlt-peer>] [vlan <1-4094>]

no i-sid <1-16777214> vlan <1-4094> [port <port>]

Default

None

Command mode


Command parameters

Parameter Descriptionport <port> Configures a switched or transparent UNI.port <smlt-peer> Configures a transparent UNI on SMLT peer.vlan <1-4094> Configures a C-VLAN UNI.



Avaya.com/support


Command: isis (Ethernet InterfaceConfiguration)


isis (Ethernet Interface Configuration)

Create an Intermediate-System-to-Intermediate-System (IS-IS) circuit and interface on the selected ports.

Syntax

default isis enable

isis

isis enable

no isis

no isis enable

Default

None

Command mode


Command parameters


enable Enables the Intermediate-System-to-Intermediate-System (IS-IS) circuit and interface onthe selected ports.



Avaya.com/support


Command: isis hello-auth (EthernetInterface Configuration)


isis hello-auth (Ethernet Interface Configuration)

Specify the authentication type used for Intermediate-System-to-Intermediate-System (IS-IS) hello packets on the interface. Thetype can be one of the following: none, simple or hmac-md5.

Syntax

default isis hello-auth

isis hello-auth type { none | simple | hmac-md5 }

isis hello-auth type { simple | hmac-md5 } key WORD

isis hello-auth type { simple | hmac-md5 } key WORD<1-16> key-id <1-255>

no isis hello-auth

Default

The default hello-auth type is none.

Command mode


Command parameters


key WORD Specifies the authentication key (password) used by the receiving router to verify thepacket.

key-id<1-255>

Specifies the optional key ID.

type {none |simple |hmac-md5}

Specifies the authentication type used for IS-IS hello packets on the interface. The typecan be one of the following: none, simple or hmac-md5. Simple password authenticationuses a text password in the transmitted packet. The receiving router uses anauthentication key (password) to verify the packet. MD5 authentication creates anencoded checksum in the transmitted packet. The receiving router uses an authenticationkey (password) to verify the MD5 checksum of the packet. There is an optional key ID.The default type is none.



Avaya.com/support


Command: isis l1-dr-priority (EthernetInterface Configuration)


isis l1-dr-priority (Ethernet Interface Configuration)

Configure the Level 1 Intermediate-System-to-Intermediate-System (IS-IS) designated router priority to the specified value.

Syntax

default isis l1-dr-priority

isis l1-dr-priority <0-127>

no isis l1-dr-priority

Default

The default Level 1 designated router priority value is 64.

Command mode


Command parameters


<0-127> Configures the Level 1 Intermediate-System-to-Intermediate-System (IS-IS) designatedrouter priority to the specified value.



Avaya.com/support


Command: isis l1-hello-interval(Ethernet Interface Configuration)


isis l1-hello-interval (Ethernet Interface Configuration)

Configure the hello interval to change how often hello packets are sent out from an interface level.

Syntax

default isis l1-hello-interval

isis l1-hello-interval <1-600>

no isis l1-hello-interval

Default

The default Level 1 hello interval value is 9 seconds.

Command mode


Command parameters

Parameter Description<1-600> Configures the Level 1 hello interval.



Avaya.com/support


Command: isis l1-hello-multiplier(Ethernet Interface Configuration)


isis l1-hello-multiplier (Ethernet Interface Configuration)

Configure the hello multiplier to specify how many hellos the Avaya Virtual Services Platform 7000 Series switch must miss beforeit considers the adjacency with a neighboring switch down.

Syntax

default isis l1-hello-multiplier

isis l1-hello-multiplier <2-100>

no isis l1-hello-multiplier

Default

The default Level 1 hello-multiplier value is 3 seconds.

Command mode


Command parameters

Parameter Description<2-100> Configures the Level 1 hello multiplier.



Avaya.com/support


Command: isis spbm (EthernetInterface Configuration)


isis spbm (Ethernet Interface Configuration)

Enable the Shortest Path Bridging MAC (SPBM) instance on the Intermediate-System-to-Intermediate-System (IS-IS) interfaces.

Syntax

default isis spbm <1-100> interface-type

default isis spbm <1-100> l1-metric

isis spbm <1-100>

isis spbm <1-100> interface-type {pt-pt}

isis spbm <1-100> l1-metric <1-16777215>

no isis spbm <1-100>

no isis spbm <1-100> interface-type

no isis spbm <1-100> l1-metric

Default

None

Command mode


Command parameters

Parameter Description<1-100> Specifies the Shortest Path Bridging MAC (SPBM) instance ID.interface-type {pt-pt}

Configures the Shortest Path Bridging MAC (SPBM) instance interfacetype.

l1-metric <1-16777215>

Configures the cost for the Shortest Path Bridging MAC (SPBM) instance.



Avaya.com/support


Command: ist


ist

Configures Inter Switch Trunk (IST)

Syntax

default ist

ist [enable] [peer-ip <A.B.C.D>] [vlan <1-4094>]

no ist

Default

None

Command mode


Command parameters

Parameter Descriptionenable Enables the IST on the specified MLT.peer-ip <A.B.C.D> Specifies the peer IP address for the IST.vlan <1-4094> Specifies a VLAN ID for the IST.



Avaya.com/support


Command: is-type


is-type

Configures the router type globally.

Syntax

is-type {l1}

no is-type

Default

None

Command mode


Command parameters

Parameter Description{l1} Sets the router type globally: l1: Level-1 router type



Avaya.com/support


Command: jumbo-frames


jumbo-frames

Enables jumbo frames on a switch or stack.

Syntax

default jumbo-frames enable

default jumbo-frames size

jumbo-frames enable

jumbo-frames size <1519-9216>

no jumbo-frames enable

Default

Enabled

Command mode


Command parameters

Parameter Descriptionenable Enables jumbo frames support.size <1519-9216> Configures the jumbo frames maximum size. The default is 9216.



Avaya.com/support


Command: l2 ping


l2 ping

Triggers a Layer 2 ping, which acts like a native ping. Enable Connectivity Fault Management (CFM) to debug Layer 2.

Syntax

l2 ping vlan <1-4094> mac <H.H.H>

l2 ping vlan <1-4094> mac <H.H.H> burst-count <1-200>

l2 ping vlan <1-4094> mac <H.H.H> data-tlv-size <0-400>

l2 ping vlan <1-4094> mac <H.H.H> frame-size <64-1500>

l2 ping vlan <1-4094> mac <H.H.H> priority <0-7>

l2 ping vlan <1-4094> mac <H.H.H> source-mode nodal

l2 ping vlan <1-4094> mac <H.H.H> source-mode smltVirtual

l2 ping vlan <1-4094> mac <H.H.H> testfill-pattern allZero

l2 ping vlan <1-4094> mac <H.H.H> testfill-pattern allZeroCrc

l2 ping vlan <1-4094> mac <H.H.H> testfill-pattern pseudoRandomBitSequence

l2 ping vlan <1-4094> mac <H.H.H> testfill-pattern pseudoRandomBitSequenceCrc

l2 ping vlan <1-4094> mac <H.H.H> time-out <1-10>

l2 ping vlan <1-4094> routernodename WORD

l2 ping vlan <1-4094> routernodename WORD burst-count <1-200>

l2 ping vlan <1-4094> routernodename WORD data-tlv-size <0-400>

l2 ping vlan <1-4094> routernodename WORD frame-size <64-1500>

l2 ping vlan <1-4094> routernodename WORD priority <0-7>

l2 ping vlan <1-4094> routernodename WORD source-mode nodal

l2 ping vlan <1-4094> routernodename WORD source-mode smltVirtual

l2 ping vlan <1-4094> routernodename WORD testfill-pattern allZero

l2 ping vlan <1-4094> routernodename WORD testfill-pattern allZeroCrc

l2 ping vlan <1-4094> routernodename WORD testfill-pattern pseudoRandomBitSequence

l2 ping vlan <1-4094> routernodename WORD testfill-pattern pseudoRandomBitSequenceCrc

l2 ping vlan <1-4094> routernodename WORD time-out <1-10>

Default

None

Command mode

User EXEC

Command parameters

Parameter Description<1-4094> Specifies the VLAN ID.burst-count <1-200> Specifies the burst count.data-tlv-size <0-400> Specifies the data Type-Length-Value (TLV) size. The default is 0.frame-size <64-1500> Specifies the frame size. The default is 0.mac <H.H.H> Specifies the MAC address.priority <0-7> Specifies the priority. The default is 7.routernodename WORD Specifies the router node name.

source-mode nodal

Specifies the source mode of nodal. Nodal MPs provide both MEPand MIP functionality for SPBM deployments. Nodal MPs areassociated with a B-VLAN and are VLAN encapsulated packets.The default is nodal. This mode applies to both B-VLANs and C-VLANs.

source-mode smltVirtual

Specifies the source mode of smltVirtual. Virtual Services Platform7000 Series supports SMLT interaction with SPBM. The platformuses two B-VIDs into the core from each pair of SMLT terminatingnodes. Both nodes advertise the Nodal B-MAC into the core onboth B-VIDS. In addition each node advertises the SMLT virtual B-MAC on one of the two B-VLANs. The default is nodal.

testfill-pattern allZero

Specifies the testfill pattern. The range is: allZero: null signalwithout cyclic redundancy check; allZeroCrc: null signal with cyclicredundancy check with 32-bit polynomial;pseudoRandomBitSequence: PRBS without cyclic redundancycheck; or pseudoRandomBitSequenceCrc: PBRS with cyclicredundancy check with 32-bit polynomial. A cyclic redundancycheck is a code that detects errors. The default is allZero.

testfill-patternallZeroCrc


testfill-patternpseudoRandomBitSequence


testfill-pattern

Specifies the testfill pattern. The range is: allZero: null signalwithout cyclic redundancy check; allZeroCrc: null signal with cyclicredundancy check with 32-bit polynomial;pseudoRandomBitSequence: PRBS without cyclic redundancy

pseudoRandomBitSequenceCrc check; or pseudoRandomBitSequenceCrc: PBRS with cyclicredundancy check with 32-bit polynomial. A cyclic redundancycheck is a code that detects errors. The default is allZero.

time-out <1-10> Specifies the interval in seconds. The default is 3.



Avaya.com/support


Command: l2 traceroute


l2 traceroute

Triggers a Layer 2 traceroute, which acts like native traceroute. Enable Connectivity Fault Management (CFM) to debug Layer 2.

Syntax

l2 traceroute vlan <1-4094> mac <H.H.H>

l2 traceroute vlan <1-4094> mac <H.H.H> priority <0-7>

l2 traceroute vlan <1-4094> mac <H.H.H> priority <0-7> ttl-value <1-255>

l2 traceroute vlan <1-4094> mac <H.H.H> source-mode nodal

l2 traceroute vlan <1-4094> mac <H.H.H> source-mode nodal ttl-value <1-255>

l2 traceroute vlan <1-4094> mac <H.H.H> source-mode smltVirtual

l2 traceroute vlan <1-4094> mac <H.H.H> source-mode smltVirtual ttl-value <1-255>

l2 traceroute vlan <1-4094> mac <H.H.H> ttl-value <1-255>

l2 traceroute vlan <1-4094> mac <H.H.H> ttl-value <1-255> vrf WORD<0-16>

l2 traceroute vlan <1-4094> routernodename WORD

l2 traceroute vlan <1-4094> routernodename WORD priority <0-7>

l2 traceroute vlan <1-4094> routernodename WORD priority <0-7> ttl-value <1-255>

l2 traceroute vlan <1-4094> routernodename WORD source-mode nodal

l2 traceroute vlan <1-4094> routernodename WORD source-mode nodal ttl-value <1-255>

l2 traceroute vlan <1-4094> routernodename WORD source-mode smltVirtual

l2 traceroute vlan <1-4094> routernodename WORD source-mode smltVirtual ttl-value <1-255>

l2 traceroute vlan <1-4094> routernodename WORD ttl-value <1-255>

Default

None

Command mode

User EXEC

Command parameters


<1-4094> Specifies the VLAN ID.mac <H.H.H> Specifies the MAC address.priority <0-7> Specifies the priority. The default is 7.routernodename WORD Specifies the router node name.source-mode<nodal|smltVirtual>

Specifies the source mode as nodal or smltVirtual. Use the smltVirtualvalue with B-VLANs only. The default is nodal.

ttl-value <1-255> Specifies the time-to-live (TTL) value. The default is 64.



Avaya.com/support


Command: l2 tracetree


l2 tracetree

Triggers a Layer 2 tracetree. Layer 2 tracetree allows a user to trigger a multicast link trace message (LTM) by specifying theBackbone VLAN (B-VLAN) and service instance identifier (I-SID). The command allows the user to view a multicast tree on theSPBM B-VLAN from the source node to the destination nodes for a particular I-SID.

Syntax

l2 tracetree vlan <1-4094> i-sid <1-16777215>

l2 tracetree vlan <1-4094> i-sid <1-16777215> mac <H.H.H>

l2 tracetree vlan <1-4094> i-sid <1-16777215> mac <H.H.H> priority <0-7>

l2 tracetree vlan <1-4094> i-sid <1-16777215> mac <H.H.H> source-mode nodal

l2 tracetree vlan <1-4094> i-sid <1-16777215> mac <H.H.H> source-mode smltVirtual

l2 tracetree vlan <1-4094> i-sid <1-16777215> mac <H.H.H> ttl-value <1-255>

l2 tracetree vlan <1-4094> i-sid <1-16777215> priority <0-7>

l2 tracetree vlan <1-4094> i-sid <1-16777215> routernodename WORD

l2 tracetree vlan <1-4094> i-sid <1-16777215> routernodename WORD priority <0-7>

l2 tracetree vlan <1-4094> i-sid <1-16777215> routernodename WORD source-mode nodal

l2 tracetree vlan <1-4094> i-sid <1-16777215> routernodename WORD source-mode smltVirtual

l2 tracetree vlan <1-4094> i-sid <1-16777215> routernodename WORD ttl-value <1-255>

l2 tracetree vlan <1-4094> i-sid <1-16777215> source-mode nodal

l2 tracetree vlan <1-4094> i-sid <1-16777215> source-mode smltVirtual

l2 tracetree vlan <1-4094> i-sid <1-16777215> ttl-value <1-255>

Default

None

Command mode

User EXEC

Command parameters

Parameter Description<1-16777215> Specifies the service instance identifier (I-SID).<1-4094> Specifies the VLAN ID.

mac <H.H.H> Specifies the MAC address.priority <0-7> Specifies the priority value. The default is 7.routernodename WORD Specifies the router node name.

source-mode nodal Specifies the source mode of nodal or smltVirtual. The default isnodal.

source-modesmltVirtual

Specifies the source mode of nodal or smltVirtual. The default isnodal.

ttl-value <1-255> Specifies the time-to-live (TTL) value. The default is 64.



Avaya.com/support


Command: lacp aggregation


lacp aggregation

Enables the port aggregation mode.

Syntax

default lacp aggregation [port <port>] enable

lacp aggregation [port <port>] enable

no lacp aggregation [port <port>] enable

Default

Disabled

Command mode


Command parameters

Parameter Descriptionenable Enable port aggregation mode. The default is disabled.port <port> Specify port list.



Avaya.com/support


Command: lacp clear-stats


lacp clear-stats

Clears LACP statistics.

Syntax

lacp clear-stats [port <port>]

Default

None

Command mode


Command parameters

Parameter Descriptionport <port> Specify port list.



Avaya.com/support


Command: lacp key (Ethernet InterfaceConfiguration)


lacp key (Ethernet Interface Configuration)

Configures the administrative LACP key for a set of ports.

Syntax

default lacp key [port <port>]

lacp key [port <port>] <1-4095>

Default

None

Command mode


Command parameters

Parameter Description<1-4095> Configures the LACP key to use.port <port> Specify port list.



Avaya.com/support


Command: lacp key (GlobalConfiguration)


lacp key (Global Configuration)

Configures LACP Key to MLT mappings.

Syntax

default lacp key <1-4095>

lacp key <1-4095> mlt-id <1-64> [smlt-id <1-512>]

Default

None

Command mode


Command parameters

Parameter Description<1-4095> Specifies the LACP administration key.mlt-id <1-64> Specifies the MLT ID.smlt-id <1-512> Specifies the SMLT ID.



Avaya.com/support


Command: lacp mode


lacp mode

Configures the LACP mode of operations for a set of ports.

Syntax

default lacp mode [port <port>]

lacp mode [port <port>] {active | off | passive }

Default

Off

Command mode


Command parameters


active The port will participate as an active Link Aggregation port. Ports in active mode sendLACPDUs periodically to the other end to negotiate for link aggregation.

off The port does not participate in Link Aggregation

passiveThe port will participate as a passive Link Aggregation port. Ports in passive mode sendLACPDUs only when the configuration is changed or when its link partner communicatesfirst.

port<port>

Specify port list.



Avaya.com/support


Command: lacp port-mode


lacp port-mode

Configures LACP port mode.

Syntax

default lacp port-mode

lacp port-mode advance

lacp port-mode default

Default

Default

Command mode


Command parameters


advance

Specifies advance mode for LACP–enabled switch ports. In advance mode, when a localswitch port has LACP enabled and STP disabled, and the port is connected to non-LACPpartner port, if the link with the partner fails, the local LACP–enabled port remains in theBlocking state. In advance mode, when a local LACP– enabled switch port is removedfrom a trunk configuration because LACP is disabled on the link partner, or PDU receptiontimes out, the local LACP–enabled port remains in the Blocking state.

default

Specifies default mode for LACP–enabled switch ports. In default mode, when a localLACP– enabled switch port is connected to a non-LACP partner port, and the link to thepartner fails to converge, the LACP–enabled port state changes to Forwarding. In defaultmode, when a local LACP–enabled switch port is removed from a trunk configurationbecause LACP is disabled on the link partner, or PDU reception times out, the local LACP–enabled port functions as a standalone port. The port state is determined by STP, if STPis enabled, or by Forwarding if STP is disabled.



Avaya.com/support


Command: lacp priority


lacp priority

Configures the per-port LACP priority for a set of ports.

Syntax

default lacp priority [port <port>]

lacp priority [port <port>] <0-65535>

Default

32768

Command mode


Command parameters

Parameter Description<0-65535> Assigns a priority value.port <port> Specify port list.



Avaya.com/support


Command: lacp smlt-sys-id


lacp smlt-sys-id

Configures the SMLT system ID for LACP.

Syntax

default lacp smlt-sys-id

lacp smlt-sys-id <H.H.H>

Default

None

Command mode


Command parameters

Parameter Description<H.H.H> Specifies the ID as a MAC address.



Avaya.com/support


Command: lacp system-priority


lacp system-priority

Configures the system priority.

Syntax

default lacp system-priority <0-65535>

lacp system-priority

Default

32768

Command mode


Command parameters

Parameter Description<0-65535> Specifies the priority.



Avaya.com/support


Command: lacp timeout-time


lacp timeout-time

Configures the LACP periodic transmission timeout interval for a set of ports.

Syntax

default lacp timeout-time [port <port>]

lacp timeout-time [port <port>] {long | short}

Default

Long

Command mode


Command parameters

Parameter Description{long | short} Specify the long or short timeout interval.port <port> Specify port list.



Avaya.com/support


Command: link-state group


link-state group

Configures upstream and downstream interface associations in a LST group.

Syntax

[no] link-state group <1-2> [upstream | downstream] interface Ethernet <port>

[no] link-state group <1-2> [upstream | downstream] interface mlt <1–64>

[no] link-state group <1-2> enable

default link-state group <1-2> [upstream |downstream]

Default

None

Command mode


Command parameters

Parameter Description[upstream |downstream]interface Ethernet<port>

Specifies one or more Ethernet interface ports as upstream ordownstream LST group members. Interfaces cannot be upstream anddownstream members simultaneously.

[upstream |downstream]interface mlt <1–64>

Specifies the ID of an MLT for upstream or downstream LST groupmembers. Interfaces cannot be upstream and downstream memberssimultaneously.

<1-2> Specifies the LST group number.enable Enables the selected LST group.



Avaya.com/support


Command: lldp config-notification


lldp config-notification

Enables notification on configuration changes.

Syntax

default lldp [port <port> ] config-notification

lldp [port <port> ] config-notification

no lldp [port <port> ] config-notification

Default

Enabled

Command mode


Command parameters

Parameter Descriptionport <port> Specifies a port or list of ports



Avaya.com/support


Command: lldp location-identification


lldp location-identification

Provides location configuration information (LCI).

Syntax

default lldp location-identification [port <port>] civic-address

default lldp location-identification [port <port>] coordinate-base

default lldp location-identification [port <port>] ecs-elin

lldp location-identification [port <port>] civic-address country-code <WORD> apartment

<WORD>

lldp location-identification [port <port>] civic-address country-code <WORD> additional-

code <WORD>

lldp location-identification [port <port>] civic-address country-code <WORD> block <WORD>

lldp location-identification [port <port>] civic-address country-code <WORD> building

<WORD>

lldp location-identification [port <port>] civic-address country-code <WORD> city <WORD>

lldp location-identification [port <port>] civic-address country-code <WORD> floor <WORD>

lldp location-identification [port <port>] civic-address country-code <WORD> house-number

<WORD>

lldp location-identification [port <port>] civic-address country-code <WORD> house-number-

suffix <WORD>

lldp location-identification [port <port>] civic-address country-code <WORD> name <WORD>

lldp location-identification [port <port>] civic-address country-code <WORD> p.o.box <WORD>

lldp location-identification [port <port>] civic-address country-code <WORD> postal-

community-name <WORD>

lldp location-identification [port <port>] civic-address country-code <WORD> state <WORD>

lldp location-identification [port <port>] civic-address country-code <WORD> street <WORD>

lldp location-identification [port <port>] civic-address country-code <WORD> additional-

information <WORD>

lldp location-identification [port <port>] civic-address country-code <WORD> city-district

<WORD>

lldp location-identification [port <port>] civic-address country-code <WORD> county <WORD>

lldp location-identification [port <port>] civic-address country-code <WORD> landmark

<WORD>

lldp location-identification [port <port>] civic-address country-code <WORD> leading-

street-direction <WORD>

lldp location-identification [port <port>] civic-address country-code <WORD> place-type

<WORD>

lldp location-identification [port <port>] civic-address country-code <WORD> postal/zip-

code <WORD>

lldp location-identification [port <port>] civic-address country-code <WORD> room-number

<WORD>

lldp location-identification [port <port>] civic-address country-code <WORD> street-suffix

<WORD>

lldp location-identification [port <port>] civic-address country-code <WORD> trailing-

street-suffix <WORD>

lldp location-identification [port <port>] coordinate-base altitude <LINE> {floors|meters}

lldp location-identification [port <port>] coordinate-base datum {NAD83/MLLW | NAD83/NAVD88

|WGS84}

lldp location-identification [port <port>] coordinate-base latitude <LINE> {NORTH | SOUTH }

lldp location-identification [port <port>] coordinate-base longitude <LINE> {EAST|WEST}]

lldp location-identification [port <port>] ecs-elin

no lldp location-identification [port <port>] civic-address

no lldp location-identification [port <port>] coordinate-base

no lldp location-identification [port <port>] ecs-elin

Default

None

Command mode


Command parameters

Parameter Descriptionadditional-code <WORD> Specifies additional code.additional-information <WORD> Specifies additional location information.altitude LINE Specifies altitude.apartment <WORD> Specifies unit (apartment, suite).block <WORD> Specifies neighborhood, block.building <WORD> Specifies building (structure).city <WORD> Specifies city, township, shi (JP).

city-district <WORD> Specifies city division, city district, ward.country-code <WORD> Specifies country code.county <WORD> Specifies county, parish, gun (JP), district(IN).datum Specifies reference datum.ecs-elin Enables or disables Emergency Call Service ELIN.floor <WORD> Specifies floor.house-number <WORD> Specifies house number.house-number-suffix <WORD> Specifies house number suffix.landmark <WORD> Specifies landmark or vanity address.latitude LINE Specifies latitude.leading-street-direction <WORD> Specifies leading street direction.longitude LINE Specifies longitude.name <WORD> Specifies residence and office occupant.p.o.box <WORD> Specifies post office box.place-type <WORD> Specifies office.postal/zip-code <WORD> Specifies postal/zip code.postal-community-name <WORD> Specifies postal community name.room-number <WORD> Specifies room number.state <WORD> Specifies national subdivisions: (state, canton, region).street <WORD> Specifies street.street-suffix <WORD> Specifies street suffix.trailing-street-suffix <WORD> Specifies trailing street suffix.



Avaya.com/support


Command: lldp med-fast-start


lldp med-fast-start

Specifies the number of times the Media Endpoint Devices (MED), fast start Link Layer Discovery Protocol Data Unit (LLDPDU) issent during the activation of the fast start mechanism.

Syntax

default lldp [med-fast-start]

lldp med-fast-start <1-10>

Default

4

Command mode


Command parameters

Parameter Description<1-10> Specifies the repeat count value.



Avaya.com/support


Command: lldp med-network-policies


lldp med-network-policies

Configures LLDP Media Endpoint Devices (MED) policies for switch ports.

Syntax

default lldp med-network-policies [port <port>] {voice | voice-signalling}

lldp med-network-policies [port <port>] {voice | voice-signalling} priority <0-7>

lldp med-network-policies [port <port>] {voice | voice-signalling} dscp <0-63>

lldp med-network-policies [port <port>] {voice | voice-signalling} tagging {tagged |

untagged }

lldp med-network-policies [port <port>] {voice | voice-signalling} vlan-id <0-4094>

no lldp med-network-policies [port <port>] {voice | voice-signalling}

Default

None

Command mode


Command parameters

Parameter Descriptiondscp <0-63>

Specifies the value of the Differentiated Service Code Point (DSCP) as defined in IETFRFC 2474 and RFC 2475 that is associated with the selected switch port or ports. Valuesrange from 0–63. The default value is 46.

port<port>

Specifies the port or ports on which to configure LLDP MED policies

priority<0-7>

Specifies the value of the 802.1p priority that applies to the selected switch port or ports.Values range from 0–7. The default value is 6

tagging{tagged|untagged}

Specifies the type of VLAN tagging to apply on the selected switch port or ports. tagged—uses a tagged VLAN. untagged—uses an untagged VLAN or does not support port-based VLANs. If you select untagged, the system ignores the VLAN ID and priorityvalues, and recognizes only the DSCP value.

vlan-id<0-4094>

Specifies the VLAN identifier for the selected port or ports. Values range from 0–4094 (0is for priority tagged frames). If you select priority tagged frames, the system recognizesonly the 802.1p priority level and uses a value of 0 for the VLAN ID of the ingress port.

voice Specifies voice network policy. The default value is 46.voice-

Specifies voice signalling network policy.

signaling



Avaya.com/support


Command: lldp notification-interval


lldp notification-interval

Specifies time interval, in seconds, between successive transmissions of LLDP notifications.

Syntax

default lldp [notification-interval]

lldp notification-interval <5-3600>

Default

5

Command mode


Command parameters

Parameter Description<5-3600> Specifies the notification interval, in seconds.



Avaya.com/support


Command: lldp reinit-delay


lldp reinit-delay

Specifies time delay, in seconds, from when LLDP on switch ports is disabled to the start of reinitialization.

Syntax

default lldp [reinit-delay]

lldp reinit-delay <1-10>

Default

2

Command mode


Command parameters

Parameter Description<1-10> Specifies the reinitialize value, in seconds.



Avaya.com/support


Command: lldp status


lldp status

Configures 802.1ab port(s) admin status.

Syntax

default lldp status

lldp status {rxOnly | txAndRx | txOnly}

no lldp status

Default

None

Command mode


Command parameters

Parameter DescriptionrxOnly Specifies that the selected port or ports can only receive LLDPUs.txAndRx Specifies that the selected port or ports can both transmit and receive LLDPUs.txOnly Specifies that the selected port or ports can only transmit LLDPUs.



Avaya.com/support


Command: lldp tx-delay


lldp tx-delay

Specifies the minimum time delay, in seconds, between successive LLDP frame transmissions.

Syntax

default lldp [tx-delay]

lldp tx-delay <1-8192>

Default

2

Command mode


Command parameters

Parameter Description<1-8192> Specifies the transmission delay value, in seconds.



Avaya.com/support


Command: lldp tx-hold-multiplier


lldp tx-hold-multiplier

Specifies the multiplier to use to calculate the Type, Length, and Value (TLV) for the LLDP Time To Live (TTL).

Syntax

default lldp [tx-hold-multiplier]

lldp tx-hold-multiplier <2-10>

Default

4

Command mode


Command parameters

Parameter Description<2-10> Specifies the transmission multiplier value.



Avaya.com/support


Command: lldp tx-interval


lldp tx-interval

Specifies the time interval, in seconds, between successive LLDP transmission cycles.

Syntax

default lldp [tx-interval]

lldp tx-interval <5-32768>

Default

30

Command mode


Command parameters

Parameter Description<5-32768> Specifies the retransmit interval value, in seconds.



Avaya.com/support


Command: lldp tx-tlv


lldp tx-tlv

Sets the optional Management TLVs to be included in the transmitted LLDPDUs.

Syntax

[default] [no] lldp tx-tlv [port <port>] med {extendedPSE | inventory | location | med-

capabilities | network-policy}

[default] [no] lldp tx-tlv [port <port>] sys-name

[default] [no] lldp tx-tlv [port <port>] vendor-specific avaya {call-server | dot1q-framing

| file-server |poe-conservation}

[default] [no] lldp tx-tlv [port <port>] sys-desc

[default] [no] lldp tx-tlv [port <port>] local-mgmt-addr

[default] [no] lldp tx-tlv [port <port>] port-desc

[default] [no] lldp tx-tlv [port <port>] sys-cap

Default

None

Command mode


Command parameters

Parameter Descriptioncall-server Enables the call server TLV transmit flag.dot1q-framing Enables the Layer 2 priority tagging TLV transmit flag.file-server Enables the file server TLV transmit flag.local-mgmt-addr Specifies the local management address TLV. This TLV is enabled by default.med location Specifies the location TLV. The default is enabled.med med-capabilities

Specifies the MED capabilities TLV. The default is enabled.

med extendedPSE Specifies the extended PSE TLV. The default is disabled.med inventory Specifies the inventory TLV. The default is enabled.med network-policy

Specifies the network policy TLV. The default is enabled.

poe-conservation Enables the PoE conservation request TLV transmit flag.

port <port> Specifies a port or list of ports.

port-desc Specifies the port description TLV This TLV is enabled by default. This TLV isenabled by default.

sys-cap Specifies the system capabilities TLV.sys-desc Specifies the system description TLV. This TLV is enabled by default.sys-name Specifies the system name TLV. This TLV is enabled by default.



Avaya.com/support


Command: lldp vendor-specific avayacall-server


lldp vendor-specific avaya call-server

Configures call-server addresses.

Syntax

default lldp

default lldp vendor-specific avaya call-server [<1-8>]

lldp vendor-specific avaya call-server <1-8> <A.B.C.D> [<1-8> <A.B.C.D>]

Default

None

Command mode


Command parameters


<1-8> Specifies the call server number. You can repeat <1–8> <A.B.C.D> to define IPaddresses for all eight call servers using the same command string.

<A.B.C.D> Specifies the call server IPv4 address.



Avaya.com/support


Command: lldp vendor-specific avayafile-server


lldp vendor-specific avaya file-server

Configures file-server addresses.

Syntax

default lldp

default lldp vendor-specific avaya file-server [<1-4>]

lldp vendor-specific avaya file-server <1-4> <A.B.C.D> [<1-4> <A.B.C.D>]

Default

None

Command mode


Command parameters


<1-4> Specifies the file server number. You can repeat <1–4> <A.B.C.D> to define IPaddresses for all four local file servers using the same command string.

<A.B.C.D> Specifies the file server IPv4 address.



Avaya.com/support


Command: lldp vendor-specific(Ethernet Interface Configuration)


lldp vendor-specific (Ethernet Interface Configuration)

Configures 802.1ab vendor-specific settings.

Syntax

default lldp vendor-specific avaya dot1q-framing

default lldp vendor-specific avaya poe-conservation-request-level

lldp vendor-specific avaya dot1q-framing {auto | tagged | untagged}

lldp vendor-specific avaya poe-conservation-request-level <0-255>

Default

None

Command mode


Command parameters

Parameter Descriptiondot1q-framing{auto |tagged |untagged}

Enables the Layer 2 priority tagging TLV transmit flag. The default is auto.

poe-conservation-request-level<0-255>

Specifies the power conservation level to request for a vendor specific PD. Valuesrange from 0 to 255. With the default value of 0, the switch does not request apower conservation level for an Avaya IP phone connected to the port.



Avaya.com/support


Command: logging


logging

Modifies the system event log configuration.

Syntax

default logging

logging <disable | enable>

logging level <critical | informational | none | serious>

logging nv-level <critical | none | serious>

logging volatile <latch | overwrite>

no logging

Default

None

Command mode


Command parameters


<disable | enable> Enables or disables the event log. The defaultis enable.

level <critical | informational | none |serious>

Specifies the level of logging stored in DRAM.

nv-level <critical | none | serious> Specifies the level of logging stored inNVRAM.

volatile <latch | overwrite> Specifies the options for logging in DRAM.



Avaya.com/support


Command: logging remote


logging remote

Configures the logging of system messages on a remote server.

Syntax

default logging remote address [secondary-address]

default logging remote facility

default logging remote level

logging remote address {A.B.C.D | <WORD>} [secondary-address {A.B.C.D | <WORD>}]

logging remote enable

logging remote facility <daemon | local0 | local1 | local2 | local3 | local4 | local5 |

local6 |local7>

logging remote level <criticial | informational | none | serious>

no logging remote address [secondary-address]

no logging remote enable

no logging remote facility

no logging remote level

Default

None

Command mode


Command parameters


address {A.B.C.D | <WORD>Specifies the IPv4 or IPv6 address of theprimary remote system log server. Thedefault is 0.0.0.0.

enable Enables the system message logging onremote server.

facility <daemon | local0 | local1 |local2 | local3 | local4 | local5 |local6 |local7>

Specifies the remote logging facility.

level <criticial | informational | none Specifies the remote logging level. The default

| serious> is none.

secondary-address {A.B.C.D | <WORD>}Specifies the IPv4 or IPv6 address of thesecondary remote system log server. Thedefault is 0.0.0.0.



Avaya.com/support


Command: logout


logout

Ends the current session.

Syntax

logout

Default

None

Command mode

User EXEC



Avaya.com/support


Command: mac-address-table


mac-address-table

Configures the MAC address table.

Syntax

default mac-address-table aging-time

default mac-address-table learning [<port>]

default mac-address-table static <H.H.H> <1-4094> interface Ethernet <port>

default mac-address-table static <H.H.H> <1-4094> interface mlt <1-64>

mac-address-table aging-time <10-1000000>

mac-address-table learning [<port>]

mac-address-table static <H.H.H> <1-4094> interface Ethernet <port>

mac-address-table static <H.H.H> <1-4094> interface mlt <1-64>

no mac-address-table learning [<port>]

no mac-address-table static <H.H.H> <1-4094> interface Ethernet <port>

no mac-address-table static <H.H.H> <1-4094> interface mlt <1-64>

Default

None

Command mode


Command parameters

Parameter Description<1-4094> Specifies a VLAN ID.

<H.H.H> Specifies the static MAC address to add or remove from the MAC addresstable.

aging-time <10-1000000>

Configures the time during which the switch retains unseen MAC addresses.The default is 300 seconds.

interface Ethernet<port>

Identifies the MAC address is on an Ethernet port.

interface mlt <1-64>

Identifies the MAC address is on an MLT trunk.

learning [<port>] Enables or disables MAC address learning on all ports or specific ports. Thedefault is enabled.

static Adds or removes a static MAC address from the forwarding database table.



Avaya.com/support


Command: mac-security auto-learning


mac-security auto-learning

Configures MAC auto-learning.

Syntax

default mac-security auto-learning aging-time

default mac-security auto-learning sticky

mac-security auto-learning aging-time <0-65535>

mac-security auto-learning sticky

no mac-security auto-learning aging-time

no mac-security auto-learning sticky

Default

None

Command mode


Command parameters

Parameter Descriptionaging-time<0-65535>

Configure the interval during which the switch will auto-learn MAC addresses. Thedefault is 60 minutes.

sticky Sets MAC security mode to enable storage of automatically-learned MAC addressesacross switch reboots. The default is disabled.



Avaya.com/support


Command: mac-security disable


mac-security disable

Disables MAC-based security.

Syntax

mac-security disable

no mac-security

Default

Disabled

Command mode




Avaya.com/support


Command: mac-security enable


mac-security enable

Enables MAC-based security.

Syntax

mac-security enable

Default

Disabled

Command mode




Avaya.com/support


Command: mac-security (EthernetInterface Configuration)


mac-security (Ethernet Interface Configuration)

Configures MAC-based security for a set of ports.

Syntax

default mac-security auto-learning [port <portlist>][enable ][ max-addrs ]

default mac-security [port <portlist>] [lock-out]

mac-security [port <port>] {disable|enable}

mac-security [port <port>] learning

mac-security [port <port>] lock-out

mac-security auto-learning [port <portlist>] {disable | enable | max-addrs <1-25>}

no mac-security [port <port>] learning

no mac-security [port <port>] lock-out

no mac-security auto-learning [port <portlist>]

Default

Disabled

Command mode


Command parameters

Parameter Descriptionauto-learning Configure MAC Auto-Learning. The default is disabled.disable Disable MAC security for port(s).enable Enable MAC security for port(s).learning Enable MAC security address learning for port(s).lock-out Lock out ports from MAC security.max-addrs Specifies the maximum number of MAC address to learn.port <port> Specifies a port or list of ports



Avaya.com/support


Command: mac-security filtering


mac-security filtering

Disables or enables DA filtering for intruder addresses.

Syntax

mac-security filtering disable

mac-security filtering enable

Default

Disabled

Command mode


Command parameters

Parameter Descriptiondisable Disables DA filtering for intruder addresses.enable Enables DA filtering for intruder addresses.



Avaya.com/support


Command: mac-security intrusion-detect


mac-security intrusion-detect

Disables or enables partitioning on intrusion detection.

Syntax

mac-security intrusion-detect disable

mac-security intrusion-detect enable

mac-security intrusion-detect forever

Default

Disabled

Command mode


Command parameters

Parameter Descriptiondisable Disables partitioning on intrusion detection.enable Enables partitioning on intrusion detection.forever Enables permanent partition on intrusion detection.



Avaya.com/support


Command: mac-security intrusion-timer


mac-security intrusion-timer

Sets temporary partition time, in seconds, for intrusion detection.

Syntax

mac-security intrusion-timer <0-65535>

Default

None

Command mode


Command parameters

Parameter Description<0-65535> Specifies the time, in seconds. 0 indicates forever.



Avaya.com/support


Command: mac-security learning


mac-security learning

Disables or enables MAC address learning.

Syntax

mac-security learning disable [snmp-lock <disable | enable>]

mac-security learning enable [snmp-lock <disable | enable>]

Default

Disabled

Command mode


Command parameters

Parameter Descriptiondisable Disables MAC address learning.enable Enables MAC address learning.snmp-lock <disable |enable>

Enables or disables SNMP lock on MAC address security parameters.The default is disabled.



Avaya.com/support


Command: mac-security learning-ports


mac-security learning-ports

Modifies port participation in MAC address learning.

Syntax

mac-security learning-ports add <port>

mac-security learning-ports remove <port>

Default

None

Command mode


Command parameters

Parameter Descriptionadd <port> Adds a port or list of ports.remove <port> Removes a port or list of ports.



Avaya.com/support


Command: mac-security mac-address-table


mac-security mac-address-table

Adds addresses to MAC security address table.

Syntax

mac-security mac-address-table {address | sticky-address} <H.H.H> mlt-id <1-64>

mac-security mac-address-table {address | sticky-address} <H.H.H> port <port>

mac-security mac-address-table address <H.H.H> security-list <1-128>

no mac-security mac-address-table

no mac-security mac-address-table address <H.H.H>

no mac-security mac-address-table mlt-id <1-64>

no mac-security mac-address-table port <port>

no mac-security mac-address-table security-list <1-128>

Default

None

Command mode


Command parameters

Parameter Description{address | sticky-address} Specifies the address to add or adds a sticky address.<H.H.H> Specifies the MAC address.mlt-id <1-64> Assigns a specific trunk to a MAC address.port <port> Assigns a specific port to a MAC address.security-list <1-128> Assigns a security list to a MAC address.



Avaya.com/support


Command: mac-security mac-da-filter


mac-security mac-da-filter

Adds or deletes MAC DA filtering addresses.

Syntax

default mac-security mac-da-filter [<H.H.H>]

mac-security mac-da-filter add <H.H.H>

mac-security mac-da-filter delete <H.H.H>

no mac-security mac-da-filter [<H.H.H>]

Default

None

Command mode


Command parameters

Parameter Descriptionadd <H.H.H> Adds the address.delete <H.H.H> Deletes the address.



Avaya.com/support


Command: mac-security security-list


mac-security security-list

Modifies the port membership for a security list.

Syntax

mac-security security-list <1-128> <port>

mac-security security-list <1-128> add <port>

mac-security security-list <1-128> remove <port>

no mac-security security-list [<1-128>]

Default

None

Command mode


Command parameters

Parameter Description<1-128> Specifies a security list number.add <port> Adds a port or list of ports.remove <port> Removes a port or list of ports.



Avaya.com/support


Command: mac-security snmp-lock


mac-security snmp-lock

Enables or disables SNMP lock on MAC address security parameters.

Syntax

mac-security snmp-lock disable

mac-security snmp-lock enable

Default

Disabled

Command mode


Command parameters

Parameter Descriptiondisable Disables SNMP lock.enable Enables SNMP lock.



Avaya.com/support


Command: manual-area


manual-area

Configures an IS-IS manual area.

Syntax

manual-area <xx.xxxx.xxxx...xxxx>

no manual-area

Default

None

Command mode


Command parameters


<xx.xxxx.xxxx...xxxx>Specifies the IS-IS manual-area (1–13 bytes in the format<xx.xxxx.xxxx...xxxx>. In this release, only one manual area issupported. For IS-IS to operate, you must configure at least one area.



Avaya.com/support


Command: manualtrigger ip ripinterface vlan


manualtrigger ip rip interface vlan

Triggers a RIP update manually.

Syntax

manualtrigger ip rip interface vlan <1-4094>

Default

None

Command mode

Privileged EXEC

Command parameters




Avaya.com/support


Command: maximum-path


maximum-path

Configures the maximum number of ECMP path for static routes.

Syntax

default maximum-path

maximum-path <1-4>

no maximum-path

Default

1

Command mode


Command parameters

Parameter Description<1-4> Specifies the maximum number of paths.



Avaya.com/support


Command: max-lsp-gen-interval


max-lsp-gen-interval

Configures the maximum level, in seconds, between generated LSPs by this Intermediate System.

Syntax

default max-lsp-gen-interval

max-lsp-gen-interval <30-900>

no max-lsp-gen-interval

Default

None

Command mode


Command parameters


<30-900> Specifies the maximum interval, in seconds, between generated LSPs by this IntermediateSystem.



Avaya.com/support


Command: mda enable


mda enable

Enables the MDA slot.

Syntax

default mda enable

mda enable

no mda enable

Default

Enabled

Command mode




Avaya.com/support


Command: metric


metric

Configures the IS-IS metric type.

Syntax

default metric

metric wide

no metric

Default

Wide

Command mode


Command parameters


wide Specifies the IS-IS metric type. Only wide is supported in this release. The default valueis wide. Use the no or default options to set this parameter to the default value of wide.



Avaya.com/support


Command: mlt


mlt

Configures MultiLink Trunking (MLT) to set up MLTs on the switch.

Syntax

default mlt <1-64> bpdu

mlt <1-64> {disable | enable}

mlt <1-64> bpdu {all-ports | single-port}

mlt <1-64> learning {disable | fast | normal}

mlt <1-64> loadbalance {advance | basic}

mlt <1-64> member <port>

mlt <1-64> name <WORD>

no mlt <1-64>

Default

None

Command mode


Command parameters

Parameter Description{disable |enable}

Disables or enables the trunk. By default, a new MLT is disabled.

<1-64> Specifies the MLT ID.bpdu {all-ports| single-port}

Specifies the BPDU send and receive mode. The default is all-ports.

learning{disable | fast| normal}

Configures STP learning mode.

loadbalance{advance |basic}

Specifies the MLT load balancing mode. Basic provides MAC address-basedload balancing. Advance provides IP-based load balancing. The default isbasic.

member <port> Specifies a port or list of ports to assign as members of the MLT.

name <WORD> Specifies a unique, alphanumeric identifier for the MLT, with a maximum of 16

characters.Avaya Virtual Services Platform 7000 Series Release 10.4

NN47202-600 Avaya Command Line Interface Commands ReferenceVersion 04.01 July 2015



Command: mlt shutdown-ports-on-disable enable


mlt shutdown-ports-on-disable enable

Enables disabled trunk loop prevention.

Syntax

default mlt shutdown-ports-on-disable [enable]

mlt shutdown-ports-on-disable enable

no mlt shutdown-ports-on-disable [enable]

Default

Disabled

Command mode




Avaya.com/support


Command: mlt spanning-tree


mlt spanning-tree

Configures STP participation for MLTs.

Syntax

mlt spanning-tree <1-64> stp <1-8 | all> learning {disable | fast | normal}

Default

None

Command mode


Command parameters

Parameter Description<1-64> Specifies the MLT ID.learning {disable | fast| normal}

Configures STP learning mode.

stp <1-8 | all> Specifies the spanning tree group number or all groups associatedwith the MLT trunk.



Avaya.com/support


Command: name


name

Specify the name of the port that needs to be changed.

Syntax

default name [port <port>]

name <name>

name port <port> <name>

no name [port <port>]

Default

None

Command mode


Command parameters

Parameter Description<name> Specifies the new name.port <port> Specifies a port or list of ports.



Avaya.com/support


Command: network (OSPF RouterConfiguration)


network (OSPF Router Configuration)

Enables OSPF on an interface.

Syntax

default network <ip_address>

network {A.B.C.D} area <area_id>

no network {A.B.C.D}

Default

None

Command mode


Command parameters

Parameter Description{A.B.C.D} Specifies the IP address of interface to be enabled for OSPF routingarea<area_id>

Specifies the ID of the area assigned to the interface in dotted decimal notation(A.B.C.D)



Avaya.com/support


Command: network (RIP RouterConfiguration)


network (RIP Router Configuration)

Enables RIP on an IP interface.

Syntax

network {A.B.C.D}

no network {A.B.C.D}

Default

None

Command mode


Command parameters

Parameter Description{A.B.C.D} IP address of the interface



Avaya.com/support


Command: ntp


ntp

Enable Network Time Protocol (NTP) globally and create an authentication key.

Syntax

default ntp [authentication-key <1-2147483647>]

default ntp [interval]

no ntp [authentication-key <1-2147483647>]

ntp [authentication-key <1-2147483647> <WORD>]

ntp [interval <10-1440>]

ntp sync-now

Default

Removes the secret key

Command mode


Command parameters

Parameter Descriptionauthentication-key<1-2147483647><WORD>

Creates an authentication key for Message Digest 5 (MD5) authentication.WORD specifies the secret key.

interval <10-1440>

Specifies the time interval, in minutes, between successive Network TimeProtocol (NTP) updates. The default value is 15. If NTP is already activated, thisconfiguration does not take effect until you disable NTP, and then re-enable it.

sync-now Forces immediate NTP synchronization.



Avaya.com/support


Command: ntp server


ntp server

Add an IP address for a Network Time Protocol (NTP) server or modify existing NTP server parameters. You can configure amaximum of 10 time servers.

Syntax

default ntp server {A.B.C.D} [auth-enable] [authentication-key]

default ntp server {A.B.C.D} [enable]

no ntp server {A.B.C.D} [auth-enable]

no ntp server {A.B.C.D} [enable]

ntp server {A.B.C.D} [auth-enable] [authentication-key <1-2147483647>]

ntp server {A.B.C.D} [enable]

Default

Does not use MD5 authentication

Command mode


Command parameters


{A.B.C.D} Specifies the IP address of the Network Time Protocol (NTP) server to add ormodify.

auth-enable Activates MD5 authentication on this Network Time Protocol (NTP) server.authentication-key <1-2147483647>

Specifies the key ID value used to generate the MD5 digest for the NetworkTime Protocol (NTP) server. The default authentication key is 0, which indicatesdisabled authentication.

enable Activates the Network Time Protocol (NTP) server.



Avaya.com/support


Command: ospf maximum-path


ospf maximum-path

Configures the maximum number of ECMP path for OSPF.

Syntax

default ospf maximum-path

no ospf maximum-path

ospf maximum-path <1-4>

Default

1

Command mode


Command parameters

Parameter Description<1-4> Specifies the number of paths.



Avaya.com/support


Command: overload


overload

Sets or clears the overload condition.

Syntax

default overload

no overload

overload

Default

None

Command mode




Avaya.com/support


Command: overload-on-startup


overload-on-startup

Configure the overload-on-startup value.

Syntax

default overload-on-startup

no overload-on-startup

overload-on-startup <15-3600>

Default

None

Command mode


Command parameters

Parameter Description<15-3600>

Specifies the IS-IS overload-on-startup value in seconds. Used as a timer to control whento send out LSPs with the overload bit cleared after IS-IS startup.



Avaya.com/support


Command: password


password

Configures password security restrictions.

Syntax

default password aging-time day

default password aging-time username <WORD>

default password password-history

no password security

password aging-time day <1-2730>

password aging-time username <WORD> <1-365>

password password-history <3-10>

password security

Default

None

Command mode


Command parameters

Parameter Descriptionaging-time day <1-2730> Configures the global password validity period.aging-time username<WORD> <1-365>

Configures the password validity period for a specific user.

password-history <3-10> Configure the maximum number of passwords stored in the passwordhistory table. The default is 3.

security Enables or disables password security for the switch.



Avaya.com/support


Command: ping


ping

Ping a device to test the connection between the VSP 7000 Series switch and another network device. After you ping a device, theswitch sends an Internet Control Message Protocol (ICMP) packet to the target device. If the device receives the packet, it sends aping reply. After the switch receives the reply, a message appears that indicates traffic can reach the specified IP address. If theswitch does not receive a reply, the message indicates the address is not responding.

Syntax

ping

ping <A.B.C.D|WORD>

ping <A.B.C.D|WORD> continuous

ping <A.B.C.D|WORD> count <1-9999>

ping <A.B.C.D|WORD> datasize <64-4096>

ping <A.B.C.D|WORD> debug

ping <A.B.C.D|WORD> interval <1-60>

ping <A.B.C.D|WORD> scopeid <1-4094>

ping <A.B.C.D|WORD> scopeid mgmt

ping <A.B.C.D|WORD> source <A.B.C.D|WORD>

ping <A.B.C.D|WORD> timeout <1-120>

ping <A.B.C.D|WORD> ttl <0-255>

Default

None

Command mode

User EXEC

Command parameters

Parameter Description<A.B.C.D|WORD> Specifies the hostname, IPv4 address, or IPv6 address to ping.

continuous Configures the continuous ping at the interval rate defined by the intervalparameter (for IPv4).

count <1-9999>

Specifies the number of times to ping (for IPv4) (1-9999).

datasize <64-

4096>Specifies the size of ping data sent in byte.

debugConfigures the ping debug mode. This variable detects local software failures(ping related threads creation or write to sending socket) and receiving issues(ICMP packet too short or wrong ICMP packet type).

interval <1-60>

Specifies the interval between transmissions in seconds (1-60).

scopeid <1-4094>|mgmt

Specifies the scope ID as a VLAN ID or the management port.

source<A.B.C.D/WORD>

Specifies an IPv4 or IPv6 address that will be used as the source address in thepacket header.

timeout <1-120>

Specifies the no-answer timeout value in seconds (1-120) for IPv4.

ttl <0-255> Specifies the time to live for the ping packet. <0-255> specifies the hop limit.



Avaya.com/support


Command: ping-virtual-address


ping-virtual-address

Enables or disables ICMP echo replies from virtual router IP addresses.

Syntax

default ping-virtual-address

default ping-virtual-address enable

no ping-virtual-address

no ping-virtual-address enable

ping-virtual-address enable

Default

None

Command mode


Command parameters

Parameter Descriptionenable Enables ICMP echo replies for VRRP associated addresses



Avaya.com/support


Command: port-mirroring


port-mirroring

Modifies the port-mirroring configuration.

Syntax

no port-mirroring [<1-4>] [rspan] [rspan <1-4>]

port-mirroring <1-4> [allow-traffic] mode {Adst | Asrc | AsrcBdst | AsrcBdstOrBsrcAdst |

AsrcOrAdst | disable | ManytoOneRx | ManytoOneRxTx | ManytoOneTx | Xrx | XrxOrXtx |

XrxOrYtx | XrxYtx | XrxYtxOrYrxXtx | Xtx} monitor-port <port> mirror-MAC-A <H.H.H> [rspan-

vlan <2-4094>]

port-mirroring <1-4> [allow-traffic] mode Adst monitor-port <port> mirror-MAC-A <H.H.H>

[rspan-vlan <2-4094>]

port-mirroring <1-4> [allow-traffic] mode Asrc monitor-port <port> mirror-MAC-A <H.H.H>


port-mirroring <1-4> [allow-traffic] mode AsrcBdst monitor-port <port> mirror-MAC-A <H.H.H>

mirror-MAC-B <H.H.H> [rspan-vlan <2-4094>]

port-mirroring <1-4> [allow-traffic] mode AsrcBdstOrBsrcAdst monitor-port <port> mirror-

MAC-A <H.H.H> mirror-MAC-B [rspan-vlan <2-4094>]

port-mirroring <1-4> [allow-traffic] mode AsrcOrAdst monitor-port <port> mirror-MAC-A

<H.H.H> [rspan-vlan <2-4094>]

port-mirroring <1-4> [allow-traffic] mode disable

port-mirroring <1-4> [allow-traffic] mode ManytoOneRx monitor-port <port> mirror-MAC-A


port-mirroring <1-4> [allow-traffic] mode ManytoOneRxTx monitor-port <port> mirror-MAC-A


port-mirroring <1-4> [allow-traffic] mode ManytoOneTx monitor-port <port> mirror-MAC-A


port-mirroring <1-4> [allow-traffic] mode Xrx monitor-port <port> mirroring-port-X <port>


port-mirroring <1-4> [allow-traffic] mode XrxOrXtx monitor-port <port> mirroring-port-X

<port> [rspan-vlan <2-4094>]

port-mirroring <1-4> [allow-traffic] mode XrxOrYtx monitor-port <port> mirroring-port-X

<port> mirroring-port-Y <port> [rspan-vlan <2-4094>]

port-mirroring <1-4> [allow-traffic] mode XrxYtx monitor-port <port> mirroring-port-X

<port> mirroring-port-Y <port> [rspan-vlan <2-4094>]

port-mirroring <1-4> [allow-traffic] mode XrxYtxOrYrxXtx monitor-port <port> mirroring-

port-X <port> mirroring-port-Y <port> [rspan-vlan <2-4094>]

port-mirroring <1-4> [allow-traffic] mode Xtx monitor-port <port> mirroring-port-X <port>


port-mirroring rspan <1-4> destination-port <port> vlan <2-4094>

Default

None

Command mode


Command parameters

Parameter Description<1-4> Specifies the mirroring or RSPAN instance number.<port> Specifies the port numbers.Adst Mirror packets with destination MAC address A.allow-traffic Enables bi-directional monitor port.Asrc Mirror packets with source MAC address A.AsrcBdst Mirror packets with source MAC address A and destination MAC address B.

AsrcBdstOrBsrcAdst Mirror packets with source MAC address A and destination MAC address B orpackets with source MAC address B and destination MAC address A.

AsrcOrAdst Mirror packets with source or destination MAC address A.destination-port<port>

Specifies the RSPAN destination port.

disable Disables port-mirroring.ManytoOneRx Many to one port mirroring on ingress packets.ManytoOneRxTx Many to one port mirroring on ingress and egress packets.ManytoOneTx Many to one port mirroring on egress packets.mirror-MAC-A<H.H.H>

Specifies the mirroring MAC address A.

mirror-MAC-B<H.H.H>

Specifies the mirroring MAC address B.

mirror-port-X Specifies the mirroring port X.mirror-port-Y Specifies the mirroring port Y.monitor-port<port>

Specifies the monitoring port.

rspan-vlan <2-4094>

Enables remote port-mirroring and specifies the VLAN for mirrored traffic.

vlan <2-4094> Specifies the RSPAN VLAN.Xrx Mirror packets received on port X.XrxOrXtx Mirror packets received or transmitted on port X.XrxOrYtx Mirror packets received on port X or transmitted on port Y.

XrxYtx Mirror packets received on port X and transmitted on port Y. This mode isnot recommended for mirroring broadcast and multicast traffic.

XrxYtxOrXtxYrx Mirror packets received on port X and transmitted on port Y or packetsreceived on port Y and transmitted on port X.

Xtx Mirror packets transmitted on port X.



Avaya.com/support


Command: psnp-interval


psnp-interval

Configures the Partial Sequence Number Packet (PSNP) in seconds.

Syntax

default psnp-interval

no psnp-interval

psnp-interval <1-120>

Default

None

Command mode


Command parameters


<1-120>

Specifies the PSNP interval in seconds. This is a system level parameter that applies forlevel 1 PSNP generation on all interfaces. A longer interval reduces overhead, while ashorter interval speeds up convergence. The default value is 2. Use the no or defaultoptions to set this parameter to the default value of 2.



Avaya.com/support


Command: qos action


qos action

Creates base actions.

Syntax

no qos action <10-55000>

qos action <10-55000> [action-ext <1-55000>] [action-ext-name <WORD>] [drop-action

{deferred-pass | disable | enable}] [name <WORD>] [session-id <1-4294967295>] [set-drop-

prec {high-drop | low-drop}] [update-1p {<0-7> | use-egress | use-tos-prec}] [update-dscp

<0-63>]

Default

None

Command mode


Command parameters

Parameter Description<10-55000> Specifies the QoS action ID.action-ext <1-55000> Specifies the action extension.

action-ext-name <WORD> Specifies a label for the action extension; maximum is 16alphanumeric characters.

drop-action {deferred-pass| disable | enable}

Specifies whether packets are dropped. The default is deferred-pass.

name <WORD> Assigns a name to a QoS action with the designated action ID.session-id <1-4294967295> Specifies the session identifier.set-drop-prec {high-drop |low-drop}

Specifies the drop precedence value. The default is low-drop.

update-1p {<0-7> | use-egress | use-tos-prec}

Specifies whether 802.1p priority values are updated or leftunchanged: unchanged equals ignore.

update-dscp <0-63> Specifies whether DSCP values are updated or left unchanged;unchanged equals ignore. The default is ignore.



Avaya.com/support


Command: qos agent


qos agent

Configures global agent parameters.

Syntax

default qos agent [buffer] [nvram-delay] [oper-mode] [queue-set] [statistics-tracking]

no qos agent oper-mode [enable]

qos agent buffer <large | lossless |lossless-pfc | maximum | regular | spb-scaled>

qos agent nvram-delay <0-604800>

qos agent oper-mode [enable]

qos agent queue-set <1-8>

qos agent reset-default

qos agent reset-partial-default

qos agent statistics-tracking {aggregate | disable | individual}

Default

None

Command mode


Command parameters

Parameter Descriptionbuffer <large |lossless |lossless-pfc | maximum |regular | spb-scaled>

Configures QoS resource buffer allocation. The default is large.

nvram-delay <0-604800>

Specifies the maximum amount of time, in seconds, before nonvolatileQoS configuration is written to non-volatile storage. The default is 10seconds.

oper-mode [enable] Enables the QoS operational mode.queue-set <1-8> Specifies the default QoS CoS queue set.reset-default Restores QoS to configuration default.reset-partial-

Restores QoS to partial configuration default.

default

statistics-tracking{aggregate | disable| individual}

Specifies default QoS statistics tracking. Aggregate allocates a singlestatistics counter to track data for all classifier of the policy being created.Individual allocates individual statistics counters to track data for eachclassifier of the QoS policy being created.



Avaya.com/support


Command: qos classifier


qos classifier

Creates a classifier.

Syntax

no qos classifier <1-55000>

qos classifier <1-55000> set-id <1-55000> [name <WORD>] element-type {ip | l2 | system}

element-id <1-55000> [session-id <1-4294967295>]

Default

None

Command mode


Command parameters

Parameter Description<1-55000> Specifies the classifier ID.element-id <1-55000> Specifies the element ID.element-type {ip | l2 |system}

Specifies the element-type; either ip, l2, or system classifier.

name <WORD> Specifies the set label; maximum is 16 alphanumericcharacters.

session-id <1-4294967295> Specifies the session ID.set-id <1-55000> Specifies the classifier set ID.



Avaya.com/support


Command: qos classifier-block


qos classifier-block

Creates a classifier block entry.

Syntax

no classifier-block <1-55000>

qos classifier-block <1-55000> block-number <1-55000> name <WORD> set-id <1-55000> [eval-

order <1-65535>] [in-profile-action <1-55000>] [in-profile-action-name <WORD>] [meter <1-

55000>] [meter-name <WORD>] [session-id <1-4294967295>]

qos classifier-block <1-55000> block-number <1-55000> name <WORD> set-name <WORD> [in-

profile-action <1-55000>] [in-profile-action-name <WORD>] [meter <1-55000>] [meter-name

<WORD>] [session-id <1-4294967295>]

Default

None

Command mode


Command parameters

Parameter Description<1-55000> Specifies the classifier ID.block-number <1-55000> Specifies the classifier block number.eval-order <1-65535> Specifies the block entry evaluation order.in-profile-action <1-55000>

Specifies the in profile action to be linked to the filter block.

in-profile-action-name<WORD>

Specifies the in profile action name to be linked to the classifierblock.

meter <1-55000> Specifies the meter to be linked to the classifier block.meter-name <WORD> Specifies the meter name to be linked to the classifier block.

name <WORD> Specifies the label for the classifier block; maximum is 16alphanumeric characters.

session-id <1-4294967295>

Specifies the session ID.

set-id <1-55000> Specifies the classifier set to be linked to the classifier block.set-name <WORD> Specifies the classifier set name to be linked to the classifier block.



Command: qos clear-stats


qos clear-stats

Clears all QoS statistics counters.

Syntax

qos clear-stats

Default

None

Command mode




Avaya.com/support


Command: qos egressmap


qos egressmap

Configures the DSCP to 802.1p priority and drop precedence associations.

Syntax

default qos egressmap [ds <0-63>]

qos egressmap name <WORD> ds <0-63> 1p <0-7> dp {high-drop | low-drop} [ds-new <0-63>]

Default

None

Command mode


Command parameters

Parameter Description1p <0-7> Specifies the 802.1p priority value associated with the DSCP.dp {high-drop |low-drop}

Specifies the drop precedence values associated with the DSCP.

ds <0-63> Specifies the DSCP value used as a lookup key for 802.1p priority and dropprecedence at egress when appropriate.

ds-new <0-63> On switches that support DSCP mutation: specifies a new DSCP value to usewhen DSCP mutation is required

name <WORD> Specifies the label for the egress mapping.



Avaya.com/support


Command: qos if-action-extension


qos if-action-extension

Creates interface action extension entries.

Syntax

no qos if-action-extension <1-55000>

qos if-action-extension <1-55000> [name <WORD>] egress-ucast <port> egress-non-ucast <port>

[session-id <1-4294967295>]

Default

None

Command mode


Command parameters

Parameter Description<1-55000> Specifies the interface action ID.egress-non-ucast <port> Specifies redirection of non-unicast to specified port or ports.egress-ucast <port> Specifies redirection of unicast to specified port or ports.name <WORD> Assigns a name to a QoS action with the designated action ID.session-id <1-4294967295> Specifies the session ID.



Avaya.com/support


Command: qos if-assign (EthernetInterface Configuration)


qos if-assign (Ethernet Interface Configuration)

Adds ports to an interface group.

Syntax

no qos if-assign [port <port>]

qos if-assign name <WORD>

qos if-assign port <port> name <WORD>

Default

None

Command mode


Command parameters

Parameter Descriptionname <WORD> Specify name of interface groupport <port> Specify list of ports



Avaya.com/support


Command: qos if-assign (GlobalConfiguration)


qos if-assign (Global Configuration)

Add interfaces to an interface group.

Syntax

no qos if-assign [port <port>]

qos if-assign name <WORD>

qos if-assign port <port> name <WORD>

Default

None

Command mode


Command parameters

Parameter Descriptionname <WORD> Specify name of interface groupport <port> Specify list of ports



Avaya.com/support


Command: qos if-group


qos if-group

Creates an interface group.

Syntax

no qos if-group name <WORD>

qos if-group name <WORD> class {trusted | unrestricted | untrusted | untrustedbasic |

untrustedv4v6}

Default

None

Command mode


Command parameters

Parameter Descriptionclass {trusted | unrestricted| untrusted | untrustedbasic| untrustedv4v6}

Specifies class of traffic received on interfaces associatedwith this interface group. The default is trusted.

name <WORD>Specifies the name of the interface group. The maximumlength of the name is 32 US-ASCII characters. The namemust begin with a letter a..z or A..Z.



Avaya.com/support


Command: qos if-queue-shaper


qos if-queue-shaper

Creates an egress queue shaper for one or more interfaces.

Syntax

no qos if-queue-shaper port <port> [queue <1-8>]

qos if-queue-shaper port <port> queue <1-8> name <WORD> shape-rate <0-10230000> shape-min-

rate <0-10230000>

qos if-queue-shaper queue <1-8> name <WORD> shape-rate <0-10230000> shape-min-rate <0-

10230000>

Default

None

Command mode


Command parameters


name <WORD> Specifies an alphanumeric label used to identify the QoS interface queue shaper.Value is a character string ranging from 1–16 characters in length.

port <port> Specifies the port or list of ports for which to apply egress queue shaping

queue <1-8>Specifies the queue for the selected interface port or ports, on which traffic isshaped. The range of available values is determined by the OoS agent default queueconfiguration.

shape-min-rate <0-10230000>

Specifies the minimum QoS interface queue shaping rate, in kilobits per second(Kbps). Values range from 0 to10230000 Kbps.

shape-rate<0-10230000>

Specifies the QoS interface queue shaping rate, in kilobits per second (Kbps). Valuesrange from 0 to 10230000 Kbps



Avaya.com/support


Command: qos if-shaper


qos if-shaper

Configures the interface shaping parameters for a set of ports.

Syntax

no qos if-shaper [port <port>]

qos if-shaper shape-rate <64-10230000> max-burst-rate <64-4294967295> [max-burst-duration

<1-4294967295>]

qos if-shaper name <WORD> shape-rate <64-10230000> max-burst-rate <64-4294967295> [max-

burst-duration <1-4294967295>]

qos if-shaper name <WORD> shape-rate <64-10230000> burst-size <1024 | 128 | 16 | 2 | 2048

| 256 | 32 | 4 | 4096 |512 | 64 | 8 | 8192>

qos if-shaper port <port> name <WORD> shape-rate <64-10230000> max-burst-rate <64-

4294967295> [max-burst-duration <1-4294967295>]

qos if-shaper port <port> name <WORD> shape-rate <64-10230000> burst-size <1024 | 128 | 16

| 2 | 2048 | 256 | 32 | 4 | 4096 |512 | 64 | 8 | 8192>

qos if-shaper shape-rate <64-10230000> burst-size <1024 | 128 | 16 | 2 | 2048 | 256 | 32 |

4 | 4096 |512 | 64 | 8 | 8192>

Default

None

Command mode


Command parameters

Parameter Descriptionburst-size <1024 | 128 | 16 | 2 | 2048 | 256| 32 | 4 | 4096 |512 | 64 | 8 | 8192>

Committeed burst size in Kilobytes.

max-burst-duration <1-4294967295>Maximum burst duration inmilliseconds; range is 1–4294967295ms.

max-burst-rate <64-4294967295> Maximum burst rate in kilobits/sec;range is 64-4294967295Kbits/sec.

name <WORD> Specify name for if-shaper; maximumis 16 alphanumeric characters.

port <portlist> Specify the port or list of ports forwhich to apply egress shaping.

shape-rate <64-10230000> Shaping rate in kilobits/sec; range is64-10230000 kilobits/sec.



Avaya.com/support


Command: qos ingressmap


qos ingressmap

Configures 802.1p priority-to-DSCP associations.

Syntax

default qos ingressmap

qos ingressmap [name <WORD>] 1p <0-7> ds <0-63>

Default

None

Command mode


Command parameters

Parameter Description1p <0-7> Specifies the 802.1p priority used as the lookup key for DSCP assignment at ingress.ds <0-63> Specifies the DSCP value associated with the target 802.1p priority.name <WORD> Specifies the label for the ingress mapping.



Avaya.com/support


Command: qos ip-element


qos ip-element

Adds and configures classifier entries.

Syntax

no qos ip-element <1-55000>

qos ip-element <1-55000>

qos ip-element <1-55000> ds-field <0-63>

qos ip-element <1-55000> addr-type <ipv4 | ipv6>

qos ip-element <1-55000> dst-ip <A.B.C.D/0-32>

qos ip-element <1-55000> dst-port-min <0-65535> dst-port-max <0-65535>

qos ip-element <1-55000> ip-flag <flag>

qos ip-element <1-55000> ipv4-option <no-opt | with-opt>

qos ip-element <1-55000> name <WORD>

qos ip-element <1-55000> protocol <0-255>

qos ip-element <1-55000> session-id <1-4294967295>

qos ip-element <1-55000> src-ip <A.B.C.D/0-32>

qos ip-element <1-55000> src-port-min <0-65535> src-port-max <0-65535>

qos ip-element <1-55000> tcp-control <flags>

Default

None

Command mode


Command parameters

Parameter Description<1-55000> Specifies the element ID.

addr-type <ipv4 |ipv6>

Specifies the address type. Use the value ipv4 to indicate an IPv4 addressor, on switches that support IPv6, the value ipv6 to indicate an IPv6address. The default is ipv4.

ds-field <0-63> Specifies a 6-bit DSCP value. The default is ignore.

dst-ip <A.B.C.D/0-32>

Specifies the destination IP address and mask in the form of a.b.c.d/x forIPv4, or, on switches that support IPv6, x:x:x:x:x:x:x:x/z .

dst-port-min <0-65535> dst-port-max<0-65535>

Specifies the Layer 4 destination port minimum and maximum value.

ip-flag <flag> Specifies the flags present in an IPv4 header.ipv4-option <no-opt| with-opt>

Specifies whether the Option field is present in the packet header.

name <WORD> Specifies the name of the IP element.protocol <0-255> Specifies the IPv4 protocol classifer criterial.session-id <1-4294967295>


src-ip <A.B.C.D/0-32>

Specifies the source IP address and mask in the form of a.b.c.d/x for IPv4,or, on switches that support IPv6, x:x:x:x:x:x:x:x/z.

src-port-min <0-65535> src-port-max<0-65535>

Specifies the Layer 4 source port minimum and maximum value.

tcp-control <flags> Specifies the control flags present in an TCP header.



Avaya.com/support


Command: qos l2-element


qos l2-element

Adds Layer 2 elements.

Syntax

no qos l2-element <1-55000>

qos l2-element <1-55000>

qos l2-element <1-55000> dst-mac <H.H.H>

qos l2-element <1-55000> dst-mac-mask <H.H.H>

qos l2-element <1-55000> ethertype <0x0-0xFFFF

qos l2-element <1-55000> name <WORD>

qos l2-element <1-55000> pkt-type <etherII | llc |snap>

qos l2-element <1-55000> priority <0-7 | all>

qos l2-element <1-55000> session-id <1-4294967295>

qos l2-element <1-55000> src-mac <H.H.H>

qos l2-element <1-55000> src-mac-mask <H.H.H>

qos l2-element <1-55000> vlan-min <1-4094> vlan-max <1-4094>

qos l2-element <1-55000> vlan-tag <tagged | untagged>

Default

None

Command mode


Command parameters

Parameter Description<1-55000> Specifies the element ID.dst-mac <H.H.H> Specifies the destination MAC element criteria.dst-mac-mask <H.H.H> Specifies the destination MAC mask element criteria.

ethertype <0x0-0xFFFF Specifies the Ethernet type. Valid format is 0xXXXX, forexample, 0x0801.

name <WORD> Specifies the name of the element.

pkt-type <etherII | llc|snap>

Specifies the packet frame format.

priority <0-7 | all> Specifies the 802.1p priority values.session-id <1-4294967295> Specifies the session ID.src-mac <H.H.H> Specifies the source MAC element criteria.src-mac-mask <H.H.H> Specifies the source MAC mask element criteria.vlan-min <1-4094> vlan-max<1-4094>

Specifies the VLAN ID minimum and maximum value elementcriteria.

vlan-tag <tagged | untagged> Specifies the packet format element criteria.



Avaya.com/support


Command: qos meter


qos meter

Creates a meter entry.

Syntax

no qos meter <1-5000>

qos meter <1-5000> [name <WORD>] committed-rate <64-10230000> burst-size <1024 | 128 | 16

|16384 | 2048 | 256 | 32 | 4 | 4096 | 512 | 64 | 8 | 8192> {in-profile-action <1-55000> |

in-profile-action-name <WORD>} {out-profile-action <1-1 | 9-55000> | out-profile-action-

name <WORD>} [session-id <1-4294967295>]

qos meter <1-5000> [name <WORD>] committed-rate <64-10230000> max-burst-rate <64-

4294967295> [max-burst-duration <1-4294967295>] {in-profile-action <1-55000> | in-profile-

action-name <WORD>} {out-profile-action <1-1 | 9-55000> | out-profile-action-name <WORD>}

[session-id <1-4294967295>]

Default

None

Command mode


Command parameters

Parameter Description<1-5000> Specifies the meter ID.burst-size <1024 | 128 | 16 |16384 | 2048 | 256 |32 | 4 | 4096 | 512 | 64 | 8 | 8192>

Specifies the burst size inKilobytes.

committed-rate <64-10230000> Specifies the committed ratevalue.

in-profile-action <1-55000> Specifies the in profile actionto be linked.

in-profile-action-name <WORD> Specifies the in profile actionname to be linked.

max-burst-duration <1-4294967295> Specifies the maximum burstduration in milliseconds.

max-burst-rate <64-4294967295> Specifies the maximum burstrate value.

name <WORD> Assigns a name to the meter.

out-profile-action <1-1 | 9-55000> Specifies the out profile actionto be linked.

out-profile-action-name <WORD> Specifies the out profile actionname to be linked.

session-id <1-4294967295> Specifies the session ID.



Avaya.com/support


Command: qos policy


qos policy

Creates a policy entry.

Syntax

qos policy <1-55000> [enable]

qos policy <1-55000> enable

qos policy <1-55000> if-group <WORD> clfr-type <block | classifier> {clfr-id <1-55000> |

clfr-name <WORD>} {in-profile-action <1-55000> | in-profile-action-name <WORD>} precedence

<1-8> [session-id <1-4294967295>] [track-statistics <aggregate | individual>]


clfr-name <WORD>} {meter <1-55000> | meter-name <WORD>} precedence <1-8> [session-id <1-

4294967295>] [track-statistics <aggregate | individual>]


clfr-name <WORD>} precedence <1-8> [session-id <1-4294967295>] [track-statistics <aggregate

| individual>]


clfr-name <WORD>} session-id <1-4294967295>

Default

None

Command mode


Command parameters

Parameter Description<1-55000> Specifies the policy ID.clfr-id <1-55000>

Specifies the classifier ID.

clfr-name<WORD>

Specifies the classifier by name.

clfr-type<block |classifier>

Specifies the classifier type; classifier or block.

enable Enables the policy.

if-group Specifies the interface group name to which this policy applies; maximum number

<WORD>of characters is 32 US-ASCII. The group name must begin with a letter within therange a..z or A..Z.

in-profile-action <1-55000>

Specifies the in profile action to be linked.

in-profile-action-name<WORD>

Specifies the in profile action name to be linked.

meter <1-55000>

Specifies the meter ID associated with this policy.

meter-name<WORD>

Specifies the meter name associated with this policy.

precedence<1-8>

Specifies the precedence of this policy in relation to other policies associated withthe same interface group. Evaluation goes from highest value to lowest.

session-id<1-4294967295>

Specifies the session by ID.

track-statistics<aggregate |individual>

Specifies statistics tracking. Aggregate allocates a single statistics counter to trackdata for all classifiers of the policy being created. Individual allocates individualstatistics counters to track data for each classifier of the QoS policy being created.



Avaya.com/support


Command: qos queue-set-assignment


qos queue-set-assignment

Configures 802.1p priority values.

Syntax

qos queue-set-assignment queue-set <1-8> 1p <0-7> queue <1-8>

Default

None

Command mode


Command parameters


1p <0-7> Specifies the 802.1p priority value, as a value in a range from 0 to 7, for the queueassociation being modified.

queue <1-8> Specifies the queue, within the identified queue set, to assign the 802.1p prioritytraffic to at egress.

queue-set<1-8>

Specifies the queue-set as a value in a range.



Avaya.com/support


Command: qos system-element


qos system-element

Configures system classifier element parameters that you can use in QoS policies.

Syntax

no qos system-element <1-55000>

qos system-element <1-55000>

qos system-element <1-55000> known-ip-mcast

qos system-element <1-55000> known-non-ip-mcast

qos system-element <1-55000> name <WORD>

qos system-element <1-55000> non-ip

qos system-element <1-55000> pattern-data <WORD> pattern-mask <WORD>

qos system-element <1-55000> pattern-format <tagged | untagged>

qos system-element <1-55000> pattern-ip-version <ipv4 | ipv6 | non-ip>

qos system-element <1-55000> pattern-l2-format <etherII | llc | snap>

qos system-element <1-55000> session-id <1-4294967295>

qos system-element <1-55000> unknown-ip-mcast

qos system-element <1-55000> unknown-non-ip-mcast

qos system-element <1-55000> unknown-ucast

Default

None

Command mode


Command parameters

Parameter Description<1-55000> Specifies the system classifier element entry ID.known-ip-mcast Specifies the filter on known multicast destination address.known-non-ip-mcast Specifies the filter on known non IP multicast destination address.name <WORD> Specifies a unique alphanumeric identifier for the system element.

non-ip Specifies the filter on non IP packets as the destination address.pattern-data <WORD>pattern-mask <WORD>

Specifies the byte pattern data and mask to filter on. The format ofthe WORD string is in the form of XX:XX:XX:....:XX.

pattern-format <tagged| untagged>

Specifies the format of data/mask pattern.

pattern-ip-version<ipv4 | ipv6 | non-ip>

Specifies the IP version of the pattern data or mask.

pattern-l2-format<etherII | llc | snap>

Specifies the format of the Layer 2 pattern data and mask.

session-id <1-4294967295>


unknown-ip-mcast Specifies the filter on unknown multicast destination address.unknown-non-ip-mcast Specifies the filter on unknown non IP multicast destination address.unknown-ucast Specifies the Filter on unknown unicast destination address.



Avaya.com/support


Command: qos traffic-profile classifier


qos traffic-profile classifier

Creates and configures a traffic profile classifier for a QoS policy. You can configure multiple parameters using the same commandstring. The syntax section does not include the possible parameter combinations. To understand the possible combinations, usethe question mark Help in ACLI to determine which parameters can be entered in the same command string.

Syntax

no qos traffic-profile classifier name <WORD> [eval-order <1-255>]

qos traffic-profile classifier name <WORD>

qos traffic-profile classifier name <WORD> addr-type {ipv4 | ipv6}

qos traffic-profile classifier name <WORD> block <WORD>

qos traffic-profile classifier name <WORD> committed-rate <64-10230000> committed-burst-

size <1024 | 128 | 16 |16384 | 2048 | 256 | 32 | 4 | 4096 | 512 | 64 | 8 | 8192>

qos traffic-profile classifier name <WORD> committed-rate <64-10230000> max-burst-rate <64-

4294967295> max-burst-duration <1-4294967295>

qos traffic-profile classifier name <WORD> drop-action disable

qos traffic-profile classifier name <WORD> drop-out-action <disable | enable>

qos traffic-profile classifier name <WORD> ds-field <0-63>

qos traffic-profile classifier name <WORD> dst-ip <A.B.C.D/0-32>

qos traffic-profile classifier name <WORD> dst-mac <H.H.H> dst-mac-mask <H.H.H>

qos traffic-profile classifier name <WORD> dst-port-min <0-65535> dst-port-max <0-65535>

qos traffic-profile classifier name <WORD> ethertype <0x0-0xFFFF>

qos traffic-profile classifier name <WORD> eval-order <1-255>

qos traffic-profile classifier name <WORD> ip-flag <flag>

qos traffic-profile classifier name <WORD> ipv4-option <no-opt | with-opt>

qos traffic-profile classifier name <WORD> master

qos traffic-profile classifier name <WORD> pkt-type <etherII | llc | snap>

qos traffic-profile classifier name <WORD> priority <0-7 | all>

qos traffic-profile classifier name <WORD> protocol <0-255>

qos traffic-profile classifier name <WORD> set-drop-prec <high-drop | low-drop>

qos traffic-profile classifier name <WORD> set-drop-prec-out-action <high-drop | low-drop>

qos traffic-profile classifier name <WORD> src-ip <A.B.C.D/0-32>

qos traffic-profile classifier name <WORD> src-mac <H.H.H> src-mac-mask <H.H.H>

qos traffic-profile classifier name <WORD> src-port-min <0-65535> src-port-max <0-65535>

qos traffic-profile classifier name <WORD> tcp-control <flag>

qos traffic-profile classifier name <WORD> update-1p {0-7 | use-egress | use-tos-prec}

qos traffic-profile classifier name <WORD> update-dscp <0-63>

qos traffic-profile classifier name <WORD> update-dscp-out-action <0-63>

qos traffic-profile classifier name <WORD> vlan-min <1-4094> vlan-max <1-4094>

qos traffic-profile classifier name <WORD> vlan-tag <tagged | untagged>

Default

None

Command mode


Command parameters


addr-type {ipv4 | ipv6} Specifies the type of IP address used by this classifier entry.The type is limited to IPv4 and IPv6 addresses.

block <WORD>Specifies an alphanumeric label, ranging from 1 to 16characters, to identify traffic profile classifier elements that areof the same block.

committed-burst-size <1024 |128 | 16 |16384 | 2048 |256 | 32 | 4 | 4096 | 512 |64 | 8 | 8192>

Specifies the burst size in Kilobytes.

committed-rate <64-10230000> Specifies the committed rate for metering.

drop-action disable Specifies whether to drop (enable) or pass (disable) trafficmatching the classifier criteria.

drop-out-action <disable |enable>

Specifies whether to drop (enable) or pass (disable) out ofprofile packets.

ds-field <0-63> Specifies the value for the DiffServ Codepoint (DSCP) in apacket.

dst-ip <A.B.C.D/0-32> Specifies the IP address and subnet mask to match against thedestination IP address of a packet.

dst-mac <H.H.H> dst-mac-mask<H.H.H>

Specifies the MAC address to which the MAC destinationaddress of incoming packets is compared.

dst-port-min <0-65535> dst-port-max <0-65535>

Specifies the minimum value for the Layer 4 destination portclassifier.

ethertype <0x0-0xFFFF> Specifies the type of information carried in the data portion ofthe frame.

eval-order <1-255> Specifies the evaluation order for all elements with the same

name.ip-flag <flag> Specifies the IP fragment flag criteria.ipv4-option <no-opt | with-opt>

Specifies the IPv4 option criteria.

master Designates the classifier as the master block member.max-burst-duration <1-4294967295>

Specifies the maximum burst duration in milliseconds.

max-burst-rate <64-4294967295>

Specifies the maximum burst rate value.

name <WORD>

Specifies an alphanumeric identifier for the traffic profileclassifier. The value is a character string from 1–16 charactersin length. All classifiers associated with a specific traffic-profilefilter set share the same name.

pkt-type <etherII | llc |snap>

Specifies the filter packet format ethertype encoding criteria.

priority <0-7 | all> Specifies a value for the 802.1p user priority.protocol <0-255> Specifies the IPv4 protocol value.set-drop-prec <high-drop |low-drop>

Specifies the drop precedence for traffic matching the classifiercriteria.

set-drop-prec-out-action<high-drop | low-drop>

Specifies the drop precedence value associated with out ofprofile traffic.

src-ip <A.B.C.D/0-32> Specifies the IPv4 address and subnet mask to match to thesource IP address of a packet.

src-mac <H.H.H> src-mac-mask<H.H.H>

Specifies the MAC source MAC address of incoming packets.

src-port-min <0-65535> src-port-max <0-65535>

Specifies the minimum value for the Layer 4 source portnumber in a packet.

tcp-control <flag> Specifies the TCP control criteria.update-1p {0-7 | use-egress| use-tos-prec}

Specifies the 802.1p user priority update value.

update-dscp <0-63> Specifies the DSCP update value.update-dscp-out-action <0-63>

Specifies the DSCP update value in out of profile packets.

vlan-min <1-4094> vlan-max<1-4094>

Specifies the minimum and maximum VLAN ID value for theclassifier.

vlan-tag <tagged | untagged> Specifies the VLAN tag classifier criteria.



Avaya.com/support


Command: qos traffic-profile set


qos traffic-profile set

Creates and configures a new QoS traffic profile filter set or modify an existing QoS traffic profile filter set.

Syntax

no qos traffic-profile set port <port> name <WORD> [enable]

qos traffic-profile set port <port> name <WORD> [enable]

qos traffic-profile set port <port> name <WORD> committed-rate <64-10230000> committed-

burst-size <1024 | 128 | 16 |16384 | 2048 | 256 | 32 | 4 | 4096 | 512 | 64 | 8 | 8192>

qos traffic-profile set port <port> name <WORD> committed-rate <64-10230000> max-burst-rate

<64-4294967295> max-burst-duration <1-4294967295>

qos traffic-profile set port <port> name <WORD> meter-mode {classifier | individual-per-

policy | uniform-per-policy}

qos traffic-profile set port <port> name <WORD> track-statistics {aggregate | disable

|individual}

Default

None

Command mode


Command parameters

Parameter Descriptioncommitted-burst-size <1024 | 128 | 16|16384 | 2048 | 256 | 32 | 4 | 4096 |512 | 64 | 8 | 8192>

Specifies the burst size in Kilobytes.

committed-rate <64-10230000> Specifies the committed rate for metering.enable Enables the traffic profile filter set.

max-burst-duration <1-4294967295> Specifies the maximum burst duration inmilliseconds.

max-burst-rate <64-4294967295> Specifies the maximum burst rate value.meter-mode {classifier | individual-per-policy | uniform-per-policy}

Specifies the metering type.

name <WORD>Specifies the traffic profile filter set name. Thisname is used to identify classifier elements thatare associated with the filter set.Specifies the ports on which the traffic profile

port <port> filter set is to be applied.track-statistics {aggregate | disable|individual}

Specifies how to track policy statistics for thetraffic profile filter set.



Avaya.com/support


Command: quickconfig enable


quickconfig enable

Enables quick configuration.

Syntax

default quickconfig

no quickconfig enable

quickconfig enable

Default

Disabled

Command mode




Avaya.com/support


Command: quickconfig start-recording



Records a default configuration that applies to new units joining the stack. Enter one command on each line in ACLI. The first twocomands must be enable and config term, otherwise the configuration commands that follow do not apply. Use $ as a wildcard forthe slot. The unit number is not known when a new unit joins a stack, so the wildcard can match any slot number. To end therecording process enter a . on the last line in ACLI.

Syntax


Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: radius accounting enable


radius accounting enable

Enables or disables the recording of management logon activity to the switch.

Syntax

default radius accounting enable

no radius accounting enable

radius accounting enable

Default

Disabled

Command mode




Avaya.com/support


Command: radius reachability


radius reachability

Configures RADIUS server reachability settings.

Syntax

default radius reachability

radius reachability use-icmp

radius reachability use-radius [username <name> password <password>]

Default

ICMP

Command mode


Command parameters

Parameter Descriptionuse-icmp Enables RADIUS server reachability using ICMP.use-radius Enables RADIUS server reachability using RADIUS requests.username <name> password<password>

Specifies a user identification name and password for RADIUSreachability.



Avaya.com/support


Command: radius-server


radius-server

Configures a switch to interface with a RADIUS server.

Syntax

default radius-server [encapsulation ms-chap-v2] [host] [key] [password fallback] [port]

[secondary-host] [timeout]

no radius-server [encapsulation ms-chap-v2] [host] [key] [password fallback] [secondary-

host]

radius-server encapsulation ms-chap-v2

radius-server host <A.B.C.D | WORD>

radius-server key [<key>]

radius-server password fallback

radius-server port <1-65535>

radius-server secondary-host <A.B.C.D | WORD>

radius-server timeout <1-60>

Default

None

Command mode


Command parameters


encapsulationms-chap-v2

Specifies to enable or disable Microsoft Challenge-Handshake AuthenticationProtocol version 2 (MS-CHAP-V2). MSCHAP-V2 provides an authenticator controlledpassword change mechanism also known as the change RADIUS password function.The deafult is disabled. This parameter is available only if the switch runs a secureimage.

host<A.B.C.D |WORD>

Specifies an IPv4 or IPv6 address for the primary RADIUS server.

key [<key>]

Specifies the secret authentication and encryption key used for all communicationsbetween the Network Access Server (NAS) and the RADIUS server. The key, alsoreferred to as the shared secret, must be the same as the one defined on theserver. You are prompted to enter and confirm the key.

passwordfallback

Enables or disables RADIUS password fallback. The default is disabled.

port <1-65535>

Specifies the UDP port the switch uses to interface with the RADIUS server. Thedefault is 1812.

secondary-host<A.B.C.D |WORD>

Specifies an IPv4 or IPv6 address for a secondary RADIUS server.

timeout <1-60>

Specifies the number of seconds before the switch RADIUS service request timesout. RADIUS allows three retries each for the primary and secondary server. Thedefault is 2.



Avaya.com/support


Command: radius use-management-ip


radius use-management-ip

Specifies whether generated RADIUS requests us the management IP address as the source IP address.

Syntax

default radius use-management-ip

no radius use-management-ip

radius use-management-ip

Default

Enabled

Command mode




Avaya.com/support


Command: range


range

Creates or modifies an IGMP filter profile. To enter the IGMP Filter Profile Configuration mode, use the ip igmp profile command.

Syntax

range <A.B.C.D> [A.B.C.D]

Default

None

Command mode


Command parameters

Parameter Description[A.B.C.D] Specifies the ending address of the range.<A.B.C.D> Specifies the starting address of the range.



Avaya.com/support


Command: rate-limit


rate-limit

Configures rate-limiting on the port.

Syntax

default rate-limit [port <port>]

no rate-limit [port <port>]

rate-limit [port <port>] <both <0-10> | percent <0-10> | pps <0-262143>

rate-limit [port <port>] <broadcast <0-10> | percent <0-10> | pps <0-262143>

rate-limit [port <port>] <multicast <0-10> | percent <0-10> | pps <0-262143>

Default

None

Command mode


Command parameters

Parameter Description<both <0-10> |percent <0-10> |pps <0-262143>

Apply rate-limiting to both multicast and broadcast. Enter an integer from1–10 to set the rate-limiting percentage or configure the packets-per-second.

<broadcast <0-10>| percent <0-10> |pps <0-262143>

Apply rate-limiting to broadcast packets. Enter an integer from 1–10 to setthe rate-limiting percentage or configure the packets-per-second.

<multicast <0-10>| percent <0-10> |pps <0-262143>

Apply rate-limiting to multicast packets. Enter an integer from 1–10 to setthe rate-limiting percentage or configure the packets-per-second.

port <port>Specify the port numbers to configure for rate-limiting. Enter the portnumbers to configure. If you omit this parameter, the system uses the portnumber you specified to enter the interface command mode.



Avaya.com/support


Command: rear-port mode


rear-port mode

Configures Fabric Interconnect (FI) ports on the rear of the switch.

Syntax

default rear-port mode

no rear-port mode

rear-port mode normal

rear-port mode spbm

Default

Disabled

Command mode


Command parameters

Parameter Descriptionnormal Enables rear-port mode without SPBM support.spbm Enables Shortest Path Bridging (SPB) loopback mode.



Avaya.com/support


Command: redistribute


redistribute

Configures OSPF route redistribution.

Syntax

default no redistribute <direct|rip|static>

default redistribute <direct|rip|static> enable

default redistribute <direct|rip|static> metric

default redistribute <direct|rip|static> route-policy

default redistribute <direct|rip|static> subnets

default redistribute <direct|rip|static>[enable] metric-type

no redistribute <direct|rip|static>

no redistribute <direct|rip|static> enable

no redistribute <direct|rip|static> route-policy

redistribute <direct|rip|static> enable

redistribute <direct|rip|static> metric <0-65535>

redistribute <direct|rip|static> route-policy <rmap_name>

redistribute <direct|rip|static> subnets <allow|suppress>

redistribute <direct|rip|static>[enable] metric-type <type1|type2>

Default

None

Command mode


Command parameters


<route_type> Specifies the source protocol to be redistributed. Valid options are direct, rip,and static.

metric <0-65535>

Specifies the metric value to associate with the route redistribution. This is aninteger value between 0 and 65535.

metric-type Specifies the metric type to associate with the route redistribution. Valid

<type1|type2> options are type1 and type2.route-policy<rmap_name>

Specifies the route policy to associate with route redistribution. This is thename of a previously configured route map.

subnets<allow|suppress>

Specifies the subnet advertisement setting of this route redistribution. Thisdetermines whether individual subnets are advertised. Valid options are allowand suppress.



Avaya.com/support


Command: reload


reload

Reloads the switch or stack.

Syntax

reload

reload cancel

reload force [minutes-to-wait <1-60>]

reload minutes-to-wait <1-60>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptioncancel Cancels a previously scheduled reload.force Does not ask for confirmation.minutes-to-wait <1-60> Specifies the minutes to wait before the reboot.



Avaya.com/support


Command: renew


renew

Renews a DHCP lease.

Syntax

renew dhcp

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: renumber unit


renumber unit

Renumbers unit numbers in a stack.

Syntax

renumber unit

Default

None

Command mode




Avaya.com/support


Command: restore factory-default


restore factory-default

Resets the stack or switch to the factory default configuration.

Syntax

restore factory-default

restore factory-default -y

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description-y Does not prompt for confirmation.



Avaya.com/support


Command: retransmit-lsp-interval


retransmit-lsp-interval

Configures the minimum time between retransmission of an LSP.

Syntax

default retransmit-lsp-interval

no retransmit-lsp-interval

retransmit-lsp-interval <1-300>

Default

5

Command mode


Command parameters


<1-300>

Specifies the minimum time between retransmission of an LSP. This defines how fast theswitch resends the same LSP. This is a system level parameter that applies for Level1retransmission of LSPs. The default value is 5 seconds. Use the no or default options toset this parameter to the default value of 5.



Avaya.com/support


Command: rfc1583-compatibility


rfc1583-compatibility

Configures OSPF RFC 1583 compatibility.

Syntax

default rfc1583-compatibility

default rfc1583-compatibility enable

no rfc1583-compatibility

no rfc1583-compatibility enable

rfc1583-compatibility enable

Default

None

Command mode


Command parameters

Parameter Descriptionenable Enable RFC-1583 compatibility mode



Avaya.com/support


Command: rip maximum-path


rip maximum-path

Configures the maximum number of ECMP paths for RIP.

Syntax

default rip maximum-path

no rip maximum-path

rip maximum-path <1-4>

Default

1

Command mode


Command parameters

Parameter Description<1-4> Specifies the number of paths.



Avaya.com/support


Command: rmon alarm


rmon alarm

Configures RMON alarms.

Syntax

no rmon alarm [<1-65535>]

rmon alarm <1-65535> <WORD> <1-2147483647> {absolute | delta} rising-threshold <-2147483648

- 2147483647> [<1-65535>] falling-threshold <-2147483648 - 2147483647> [<1-65535>] [owner

<owner>]

Default

None

Command mode


Command parameters

Parameter Description{absolute |delta}

Specifies the comparison method. For absolute values, the value of the MIBobject is compared directly with thresholds. For delta values, the change inthe value of the MIB object between samples is compared with thresholds.

<1-2147483647> Specifies the sampling interval, in seconds.<1-65535> Specifies a unique index for the alarm entry.

<WORD> Specifies the MIB object to be monitored. This object identifier can be anEnglish name.

falling-threshold<-2147483648 -2147483647> [<1-65535>]

The first integer value is the falling threshold value. The optional secondinteger specifies the event entry to be triggered after the falling threshold iscrossed. If omitted, or if an invalid event entry is referenced, no event istriggered.

owner <owner> Specifies the owner string to identify the alarm entry.rising-threshold<-2147483648 -2147483647> [<1-65535>]

The first integer value is the rising threshold value. The optional secondinteger specifies the event entry to be triggered after the rising threshold iscrossed. If omitted, or if an invalid event entry is referenced, no event istriggered.



Avaya.com/support


Command: rmon event


rmon event

Configures RMON event log and trap settings.

Syntax

no rmon event [<1-65535>]

rmon event <1-65535> [description <description>]

rmon event <1-65535> log

rmon event <1-65535> owner <owner> [community <community>]

rmon event <1-65535> trap

Default

None

Command mode


Command parameters

Parameter Description<1-65535> Specifies a unique index for the alarm entry.community <community> Specifies a community string.description <description> Specifies a textual description for the event.log Records events in the log table.owner <owner> Specifies the owner string to identify the alarm entry.trap Generates SNMP trap messages for events.



Avaya.com/support


Command: rmon history


rmon history

Configures RMON history settings.

Syntax

no rmon history [<1-65535>]

rmon history <1-65535> <port> <1-65535> <1-3600> [owner <owner>]

Default

None

Command mode


Command parameters

Parameter Description<1-3600> Specifies the sampling rate (how often a history sample is collected).<1-65535>

The first instance specifies a unique index for the entry. The second instance specifies thenumber of history buckets (records) to keep.

owner<owner>

Specifies the owner string.

port Specifies the port number to be monitored.



Avaya.com/support


Command: rmon stats


rmon stats

Configures RMON statistics settings.

Syntax

no rmon stats <1-65535>

rmon stats <1-65535> <port> [owner <owner>]

Default

None

Command mode


Command parameters

Parameter Description<1-65535> Specifies a unique index for the entry.owner <owner> Specifies the owner string.port Specifies the port number to be monitored.



Avaya.com/support


Command: route-map


route-map

Defines a route map that is used in the configuration of IP route policies.

Syntax

default route-map <WORD> <1-65535> [match {interface | metric | network | next-hop |

protocol | route-source | route-type}] [set {injectlist | ip-preference | mask | metric |

metric-type | nssa-pbit enable}

no route-map <WORD> <1-65535> [match {interface | metric | network | next-hop | protocol |

route-source | route-type}] [set {injectlist | ip-preference | mask | metric | metric-type

| nssa-pbit enable}

route-map <WORD> {deny | permit} <1-65535> set {injectlist <WORD> | ip-preference <0-255> |

mask <A.B.C.D> | metric <0-65535> | metric-type <type1 | type2> | nssa-pbit enable}

route-map <WORD> {deny | permit} <1-65535> enable

route-map <WORD> {deny | permit} <1-65535> match {interface <WORD> | metric <0-65535> |

network <WORD> | next-hop <WORD> | protocol <name> | route-source <WORD> | route-type <any

| external | external-1 | external-2 | internal |local>}

route-map <WORD> {deny | permit} <1-65535> name <WORD>

Default

None

Command mode


Command parameters


{deny | permit} Specifies the action to be taken when this policy is selected for a specificroute.

<1-65535> Specifies the secondary policy index sequence number to assign toindividual policies inside a larger policy group.

<WORD> Specifies an alphanumeric name for the IP route map.

enableEnables the IP route map policy index sequence number. If you do notenable the map policy index sequence number, the switch ignores theselected value. The default is disabled.

injectlist <WORD> Replaces the destination network of the route that matches this policywith the contents of the specified prefix list.

interface <WORD> Matches the IP address of the received interface against the contents ofthe specified prefix list.

ip-preference <0-255>

Specifies the route preference value to be assigned to the route thatmatches this policy. If you select a value of 0, the switch uses the globalpreference value. This parameter is used for accept policies only. Thedefault is 0.

mask <A.B.C.D> Sets the mask of the route that matches this policy. This parameter isused for RIP accept policies only. The default is 0.0.0.0.

match Specifies the match criteria for the IP route map.

metric <0-65535>

Matches the metric of the incoming advertisement or existing routeagainst the specified value or sets the value of the metric to be assignedto matching routes. If you set the match value to 0, the switch ignoresthis field. The default is 0.

metric-type <type1 |type2>

Sets the metric type for routes to be imported into the OSPF routingprotocol. The default is type2.

name <WORD> Assigns a new alphanumeric name to a previously configured IP routemap.

network <WORD> Matches the destination network against the contents of the specifiedprefix list.

next-hop <WORD> Matches the next hop IP address of the route against the contents of thespecified prefix list.

nssa-pbit enableEnables the NSSA P-bit, which notifies the ABR to export the matchingexternal route. This parameter is used for OSPF policies only. Thedefault is enable.

protocol <name>Matches the protocol through which the switch learns a route. Valuesinclude direct, static, rip, ospf, or any. You can select a list of multipleprotocols by separating the selections with commas.

route-source <WORD> Matches the source IP address for RIP routes against the contents of thespecified prefix list.

route-type <any |external | external-1 | external-2 |internal |local>

Matches a specific route. The default is any.

set Specifies an IP route map policy.



Avaya.com/support


Command: router-id


router-id

Configures the router ID.

Syntax

default router-id

no router-id

router-id <A.B.C.D>

Default

None

Command mode


Command parameters

Parameter Description<A.B.C.D> Specifies the unique identifier for the router



Avaya.com/support


Command: router isis


router isis

Enter Intermediate-System-to-Intermediate-System (IS-IS) Router Configuration mode. If you do not use an optional parameterwith the command, you enter the IS-IS Router Configuration mode.

Syntax

default router isis enable

no router isis enable

router isis [enable]

Default

Disabled

Command mode




Avaya.com/support


Command: router ospf


router ospf

Enable OSPF for the switch. If you do not use an optional parameter with the command, you enter the OSPF Router Configurationmode.

Syntax

default router ospf enable

no router ospf enable

router ospf [enable]

Default

Disabled

Command mode




Avaya.com/support


Command: router rip


router rip

Enable RIP globally. If you do not use an optional parameter with the command, you enter the RIP Router Configuration mode.

Syntax

default router rip enable

no router rip enable

router rip [enable]

Default

Disabled

Command mode




Avaya.com/support


Command: router vrrp


router vrrp

Enter VRRP Router Configuration mode. If you do not use an optional parameter with the command, you enter the VRRP RouterConfiguration mode.

Syntax

default router vrrp enable

no router vrrp enable

router vrrp [enable]

Default

Diabled

Command mode




Avaya.com/support


Command: run spbm


run spbm

Enables Avaya VENA Fabric Connect on a switch or stack. You can use the SPB script, rather than configure the minimum SPBMand IS-IS parameters. You can accept the default values, or enter a specific value at each prompt.

Syntax

run spbm

Default

None

Command mode

User EXEC



Avaya.com/support


Command: save config


save config

Write the configuration to NVRAM.

Syntax

save config

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: script run


script run

Runs an ASCII configuration file from a USB mass storage device, or from a TFTP/SFTP server on a switch or stack. The followingparameters force the script to load from the specified source, and then run.

Syntax

script run <-1-127>

script run sftp <Hostname|A.B.C.D|WORD> username <WORD>

script run tftp <Hostname|A.B.C.D|WORD> <WORD>

script run usb unit <1–8> <WORD>

Default

None

Command mode

Privileged EXEC

Command parameters


<1–127> Specifies the index in the ASCII configuration script table of the scriptto be loaded.

<Hostname|A.B.C.D|WORD> Specifies an alphanumeric host name, an IPv4 address, or an IPv6address.

<WORD> Specifies a filename for the script.sftp Specifies the script loads from the SFTP server.

tftp

Specifies the script loads from the TFTP server. You must add theenable and configure terminal commands to the ASCII configurationscript table file. If you do not add the enable and configure terminalcommands, the ASCII script does not auto download from the TFTPserver.

unit <1–8> Specifies the unit number in a stack.usb Specifies the script loads from the USB.username <WORD> Specifies a username for the script.



Avaya.com/support


ASCIIconfiguration.



Avaya.com/support


Command: serial-console


serial-console

Enables the serial console port.

Syntax

default serial-console [unit <1-8>] enable

no serial-console [unit <1-8>] enable

serial-console [unit <1-8>] enable

Default

Enabled

Command mode


Command parameters

Parameter Descriptionenable Enables the port.unit <1-8> Identifies the unit number in a stack.



Avaya.com/support


Command: serial-security enable


serial-security enable

Enables security for the serial console port.

Syntax

default serial-security enable

no serial-security enable

serial-security enable

Default

Enabled

Command mode




Avaya.com/support


Command: sflow


sflow

Configures SFLOW global settings.

Syntax

default sflow [enable]

no sflow [enable]

sflow [enable]

Default

None

Command mode


Command parameters

Parameter Descriptionenable Enables SFLOW protocol.



Avaya.com/support


Command: sflow collector


sflow collector

Configures SFLOW collectors.

Syntax

default sflow collector [<1-4>] [max-data-size]

no sflow collector [<1-4>]

sflow collector [<1-4>] [address <A.B.C.D> | <ipv6addr>] [owner <WORD/1-20>] [port<1-

65535>][max-datagram-size <400-9216>][timeout <0-65535>]

Default

None

Command mode


Command parameters

Parameter Descriptionaddress <A.B.C.D> | <ipv6addr> Specifies the ip address.LINE <1-4> Specifies the collector ID.max-datagram-size <400-9216> Specifies the maximum size of the sflow packet.owner <WORD/1-20> Specifies the name of collector.port<1-65535> Specifies the UDP port number.timeout <0-65535> Specifies the time until collector is deleted.



Avaya.com/support


Command: sflow (Ethernet InterfaceConfiguration)


sflow (Ethernet Interface Configuration)

Modify SFLOW settings on port

Syntax

default sflow port <portList> [collector <1-4>] [counter-interval] [max-header-size]

[sampling-rate [ingress | egress]]

no sflow port <portList> [collector <1-4>] [counter-interval] [max-header-size] [sampling-

rate [ingress | egress]]

sflow port <portList> [collector <1-4>] [counter-interval <1-3600>] [max-headersize <64-

256>] [sampling-rate [ingress | egress] <4096-1000000>]

Default

None

Command mode


Command parameters

Parameter Descriptioncollector <1-4> Sets collector on port.

counter-interval <1-3600> Sets counter pooling interval onport.

max-header-size <64-256> Sets maximum capturated headersize.

port [collector | counter-interval | sampling-rate]

Specifies the port.

port <portList> Specifies the port.sampling-rate [egress | ingress] <4096-1000000> Sets sampling rate on port.



Avaya.com/support


Command: sftp-server


sftp-server

Configures an SFTP server address for the switch. This command is only available if the switch runs a secure image.

Syntax

default sftp-server

no sftp-server

sftp-server <A.B.C.D|Word>

Default

0.0.0.0

Command mode


Command parameters

Parameter Description<A.B.C.D|Word> Specifies the IPv4 or IPv6 address.



Avaya.com/support


Command: show application slamonagent


show application slamon agent

Shows the SLA Mon™ configuration.

Syntax

show application slamon agent

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show arp


show arp

Shows ARP entries.

Syntax

show arp

show arp <A.B.C.D>

show arp <H.H.H>

show arp add-fail

show arp dynamic

show arp -s <A.B.C.D> <A.B.C.D>

show arp static

show arp summary

show arp vlan <1-4094>

Default

None

Command mode

User EXEC

Command parameters

Parameter Description<A.B.C.D> Displays ARP entries for a specific IP address.<H.H.H> Displays ARP entries for specific MAC address.add-fail Displays ARP entries not programmed in hardware.dynamic Displays dynamic ARP entries that do not have a valid route.-s <A.B.C.D> <A.B.C.D> Displays ARP entries for specific IP addresses and subnet masks.static Displays static ARP entries that do not have a valid route.summary Displays a summary of ARP entries.vlan <1-4094> Displays ARP entries for a specific VLAN ID.



Avaya.com/support


Command: show arp-table


show arp-table

Shows the system ARP table.

Syntax

show arp-table

show arp-table mgmt-port

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionmgmt-port Displays the system ARP cache entry table for the management port.



Avaya.com/support


Command: show audit log


show audit log

Shows the audit log.

Syntax

show audit log

show audit log asccfg

show audit log config

show audit log serial

show audit log telnet

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionasccfg Display audit log for ASCII configuration.config Display audit log save configuration.serial Display audit log for serial connections.telnet Display audit log for telnet/ssh.



Avaya.com/support


Command: show auto-negotiation-advertisements


show auto-negotiation-advertisements

Displays current auto-negotiation advertisement settings.

Syntax

show auto-negotiation-advertisements

show auto-negotiation-advertisements port <port>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionport <port> Specifies a port or list of ports.



Avaya.com/support


Command: show auto-negotiation-capabilities


show auto-negotiation-capabilities

Displays current auto-negotiation advertisement capabilities.

Syntax

show auto-negotiation-capabilities

show auto-negotiation-capabilities port <port>

Default

None

Command mode

Privileged EXEC

Command parameters




Avaya.com/support


Command: show auto-pvid


show auto-pvid

Shows Auto-PVID mode.

Syntax

show auto-pvid

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show autosave


show autosave

Displays current autosave settings.

Syntax

show autosave

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show autotopology


show autotopology

Displays autotopology information.

Syntax

show autotopology nmm-table

show autotopology settings

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionnmm-table Shows the contents of the topology table.settings Shows global settings.



Avaya.com/support


Command: show banner


show banner

Displays banner information.

Syntax

show banner

show banner custom

show banner static

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptioncustom Displays the customer banner.static Displays the static banner.



Avaya.com/support


Command: show boot


show boot

Shows boot settings.

Syntax

show boot

show boot diag

show boot image

show boot image primary

show boot image secondary

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptiondiag Displays information about diag images.image Displays information about agent image information.primary Displays primary image software version.secondary Displays secondary image software version.



Avaya.com/support


Command: show brouter


show brouter

Show brouter port information.

Syntax

show brouter

show brouter port <port>

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionport <port> Displays information for a specific port number.



Avaya.com/support


Command: show cfm spbm


show cfm spbm

Displays the global CFM SPBM configuration for SPBM VLANs.

Syntax

show cfm spbm

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show cli


show cli

Displays ACLI settings.

Syntax

show cli info

show cli mode

show cli password [type]

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptioninfo Displays general console information.mode Displays the current ACLI mode.password Displays usernames and passwords.type Displays password types.



Avaya.com/support


Command: show clock


show clock

Displays the current time.

Syntax

show clock

show clock detail

show clock summer-time

show clock time-zone

Default

None

Command mode

Privileged EXEC

Command parameters


detail In addition to displaying the current time, displays all time source current value and RTCconfiguration.

summer-time

Shows daylight saving time settings.

time-zone Shows local time zone settings.



Avaya.com/support


Command: show config-network


show config-network

Shows settings for downloading configuration files.

Syntax

show config-network

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show cpu-utilization


show cpu-utilization

Displays CPU utilization information.

Syntax

show cpu-utilization

show cpu-utilization unit <1-8>

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionunit <1-8> Displays information for a specific unit number.



Avaya.com/support


Command: show ddi-logging


show ddi-logging

Displays ports with DDI events logging disabled.

Syntax

show ddi-logging

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show diagnostics-quick-mode


show diagnostics-quick-mode

Displays the status of diagnostic quick mode.

Syntax

show diagnostics-quick-mode

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show ecmp


show ecmp

Displays ECMP settings.

Syntax

show ecmp

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show edm help-file-path


show edm help-file-path

Display the configuration information for the EDM Help files.

Syntax

show edm help-file-path

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show environmental


show environmental

Displays environmental information.

Syntax

show environmental

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show fa


show fa

Displays Fabric Attach specific settings.

Syntax

show fa

Default

None

Command mode




Avaya.com/support


Command: show fa agent


show fa agent

Display Fabric Attach agent status

Syntax

show fa agent

Default

None

Command mode




Avaya.com/support


Command: show fa element


show fa element

Displays Fabric Attach elements

Syntax

show fa element [auth-status <auth-fail> <auth-pass> <not-auth>] [client-type <6-17>]

[element-type <client> <proxy> <server>] [LINE]

Default

None

Command mode


Command parameters

Parameter Descriptionauth-status <auth-fail> Displays elements with Authentication Fail status.auth-status <auth-pass> Displays elements with Authentication Pass status.auth-status <not-auth> Displays elements with Not Authenticated status.client-type <6-17> Displays specific FA Client type elements.elements-type <client> Displays FA Client elements.elements-type <proxy> Displays FA Proxy elements.elements-type <server> Displays FA Server elements.LINE <1-4> List of ports.



Avaya.com/support


Command: show fa i-sid


show fa i-sid

Displays Fabric Attach configured UNIs.

Syntax

show fa i-sid <1-16777214>

Default

None

Command mode


Command parameters

Parameter Description<1-16777214> I-SID value.



Avaya.com/support


Command: show fa port-enable


show fa port-enable

Displays Fabric Attach port settings.

Syntax

show fa port-enable [disabled-auth] [disabled-port] [enabled-auth] [enabled-port] [LINE]

Default

None

Command mode


Command parameters

Parameter Descriptiondisabled-auth Displays only authentication-disabled ports.disabled-port Displays only FA-disabled ports.enabled-auth Displays only authentication-enabled ports.enabled-port Displays only FA-enabled ports.LINE <1-4> List of ports.



Avaya.com/support


Command: show fa uplink


show fa uplink

Displays Fabric Attach uplink data.

Syntax

show fa uplink

Default

None

Command mode




Avaya.com/support


Command: show fa vlan


show fa vlan

Display Fabric Attach VLANs.

Syntax

show fa vlan

Default

None

Command mode




Avaya.com/support


Command: show fa zero-touch-options


show fa zero-touch-options

Displays Fabric Attach Zero Touch option settings.

Syntax

show fa zero-touch-options

Default

None

Command mode




Avaya.com/support


Command: show fcoe


show fcoe

Displays configuration information for the FCoE Redirect feature.

Syntax

show fcoe

show fcoe profile

show fcoe profile <1-55000>

show fcoe profile name <WORD>

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionname <WORD> Displays an FCoE profile based on profile name.profile <1-55000> Displays an FCoE profile based on profile ID.



Avaya.com/support


Command: show flash


show flash

Displays flash information.

Syntax

show flash

show flash history

show flash unit <1-8>

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionhistory Provides counters that show flash activity.unit <1-8> Specifies the unit number in stack mode.



Avaya.com/support


Command: show http-port


show http-port

Displays the TCP port on which the web server will listen.

Syntax

show http-port

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show https-only


show https-only

Shows if the web server is configured to respond to HTTPS only, or both HTTPS and HTTP client browser requests when SSL isenabled

Syntax

show https-only

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show https-port


show https-port

Shows the value for the HTTPS port that the switch uses for secure client web browser requests

Syntax

show https-port

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show interfaces


show interfaces

Shows the status and configuration for all interfaces.

Syntax

show interfaces

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show interfaces admin-disabled


show interfaces admin-disabled

Displays the admin disabled interfaces.

Syntax

show interfaces admin-disabled

show interfaces admin-disabled <port>

Default

None

Command mode

User EXEC

Command parameters


<port> Specifies the port in one of the following formats: a single port (3), a range of ports (3-4), or a series of ports (3,5,6).



Avaya.com/support


Command: show interfaces admin-enabled


show interfaces admin-enabled

Displays the admin enabled interfaces.

Syntax

show interfaces admin-enabled

show interfaces admin-enabled <port>

Default

None

Command mode

User EXEC

Command parameters





Avaya.com/support


Command: show interfaces gbic-info


show interfaces gbic-info

Displays GBIC details.

Syntax

show interfaces gbic-info

show interfaces gbic-info <port>

Default

None

Command mode

User EXEC

Command parameters





Avaya.com/support


Command: show interfaces link-down


show interfaces link-down

Displays the interfaces with a link down.

Syntax

show interfaces link-down

show interfaces link-down <port>

Default

None

Command mode

User EXEC

Command parameters





Avaya.com/support


Command: show interfaces link-up


show interfaces link-up

Displays the interfaces with a link up.

Syntax

show interfaces link-up

show interfaces link-up <port>

Default

None

Command mode

User EXEC

Command parameters





Avaya.com/support


Command: show interfaces loopback


show interfaces loopback

Displays loopback interfaces.

Syntax

show interfaces loopback <1-16>

Default

None

Command mode

User EXEC

Command parameters

Parameter Description<1-16> Specifies the interface ID.



Avaya.com/support


Command: show interfaces names


show interfaces names

Displays interface names.

Syntax

show interfaces names

show interfaces names <port>

shows interfaces names

shows interfaces names <port>

Default

None

Command mode

User EXEC

Command parameters





Avaya.com/support


Command: show interfaces <port>


show interfaces <port>

Displays information for a list of ports.

Syntax

show interfaces <port>

show interfaces <port> config

show interfaces <port> verbose

Default

None

Command mode

User EXEC

Command parameters



config Shows the interface configuration.verbose Displays the port status for several applications.



Avaya.com/support


Command: show interfaces verbose


show interfaces verbose

Displays the port status information for several applications.

Syntax

show interfaces verbose

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip


show ip

Displays IP-related information.

Syntax

show ip

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip address


show ip address

Shows the IP address for the switch or stack.

Syntax

show ip address

show ip address source

show ip address stack

show ip address switch

show ip address unit <1-8>

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionsource Displays BOOTP and DHCP configuration.stack Displays the IP address of the stack.switch Displays the IP address of the local unit.unit <1-8> Displays the IP address of another unit in a stack.



Avaya.com/support


Command: show ip arp-inspection


show ip arp-inspection

Displays ARP inspection port information.

Syntax

show ip arp-inspection

show ip arp-inspection interface

show ip arp-inspection interface <port>

show ip arp-inspection interface Ethernet

show ip arp-inspection interface Ethernet <port>

show ip arp-inspection vlan

show ip arp-inspection vlan <vlan list>

Default

None

Command mode

User EXEC

Command parameters


<port> Specifies the port in one of the following formats: a single port (3), a range of ports(3-4), or a series of ports (3,5,6).

Ethernet Displays information about all Ethernet interfaces.interface Displays the interface configuration.vlan <vlanlist>

Specifies the VLAN ID.



Avaya.com/support


Command: show ip arp-proxy


show ip arp-proxy

Displays Proxy ARP status.

Syntax

show ip arp-proxy interface

show ip arp-proxy interface vlan <1-4094>

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptioninterface Displays the interface configuration.vlan <1-4094> Specifies a VLAN ID.



Avaya.com/support


Command: show ip-blocking


show ip-blocking

Displays the Layer 3 IP blocking state.

Syntax

show ip-blocking

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip blocking-mode


show ip blocking-mode

Displays the Layer 3 IP blocking mode.

Syntax

show ip blocking-mode

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip bootp


show ip bootp

Shows the BOOTP configation. You can also use an optional address parameter to show information similar to the show ip addresscommand, or the optional default-gateway parameter to show information similar to the show ip default-gateway command.

Syntax

show ip bootp

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip default-gateway


show ip default-gateway

Displays the IP address of the default gateway. You can also use an optional address parameter to show information similar to theshow ip address command.

Syntax

show ip default-gateway

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip default-ttl


show ip default-ttl

Displays the default time-to-live.

Syntax

show ip default-ttl

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip dhcp client lease


show ip dhcp client lease

Displays information about the DHCP client lease.

Syntax

show ip dhcp client lease

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip dhcp-relay


show ip dhcp-relay

Displays Dynamic Host Configuration Protocol (DHCP) Relay information to show relay information about DHCP routes andcounters.

Syntax

show ip dhcp-relay counters

show ip dhcp-relay fwd-path

show ip dhcp-relay fwd-path summary

show ip dhcp-relay interface Ethernet

show ip dhcp-relay interface Ethernet <port>

show ip dhcp-relay interface vlan

show ip dhcp-relay interface vlan <1-4094>

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptioncounters Displays the count of DHCP Relay requests and replies.fwd-path Displays information about DHCP Relay forward paths.interface Ethernet <port> Displays information about DHCP Relay Ethernet interfaces.interface vlan <1-4084> Displays information about DHCP Relay VLAN interfaces.summary Displays a summary of the DHCP Relay fowarding path.



Avaya.com/support


Command: show ip dhcp-snoopingbinding


show ip dhcp-snooping binding

Displays the DHCP snooping binding table.

Syntax

show ip dhcp-snooping binding

show ip dhcp-snooping binding summary

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionsummary Displays a summary of the DHCP snooping binding table.



Avaya.com/support


Command: show ip dhcp-snoopingexternal-save


show ip dhcp-snooping external-save

Displays the current operating state of DHCP snooping external save.

Syntax

show ip dhcp-snooping external-save

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip dhcp-snoopinginterface


show ip dhcp-snooping interface

Displays DHCP snooping port information.

Syntax

show ip dhcp-snooping interface

show ip dhcp-snooping interface <port>

show ip dhcp-snooping interface Ethernet

show ip dhcp-snooping interface Ethernet <port>

Default

None

Command mode

User EXEC

Command parameters



Ethernet Displays information about all Ethernet interfaces.



Avaya.com/support


Command: show ip dhcp-snooping vlan


show ip dhcp-snooping vlan

Displays DHCP snooping VLAN information.

Syntax

show ip dhcp-snooping vlan

show ip dhcp-snooping vlan <vlan list>

Default

None

Command mode

User EXEC

Command parameters

Parameter Description<vlan list> Specifies the VLAN ID.



Avaya.com/support


Command: show ip directed-broadcast


show ip directed-broadcast

Shows the interface status for direct broadcast.

Syntax

show ip directed-broadcast

show ip directed-broadcast interface

show ip directed-broadcast interface vlan

show ip directed-broadcast interface vlan <1-4094>

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptioninterface Displays the interface configuration.vlan <1-4094> Specifies a VLAN ID.



Avaya.com/support


Command: show ip dns


show ip dns

Displays the DNS client system status.

Syntax

show ip dns

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip forward-protocol


show ip forward-protocol

Displays the UDP protocol table with the UDP port numbers for each supported or designated protocol.

Syntax

show ip forward-protocol udp

show ip forward-protocol udp interface

show ip forward-protocol udp interface vlan

show ip forward-protocol udp interface vlan <1-4094>

show ip forward-protocol udp portfwdlist

show ip forward-protocol udp portfwdlist <1-128>

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptioninterface Displays information about the UDP interface.portfwdlist <1-128>

Displays the UDP port forwarding list table for the specified list or all lists onthe switch.

udp Shows configured UDP ports.vlan <1-4094> Specifies a VLAN ID.



Avaya.com/support


Command: show ip igmp


show ip igmp

Displays IGMP information.

Syntax

show ip igmp {[cache] | [group] | [group-ext] | [interface] | [profile] | [router-alert] |

[snoop-querier-addr] | [snooping] | [ssm] | [ssm-map]}

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show ip igmp cache


show ip igmp cache

Displays IGMP cache details.

Syntax

show ip igmp cache

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show ip igmp group


show ip igmp group

Displays IGMP group details.

Syntax

show ip igmp group {[count] | [group <A.B.C.D>] | [member-subnet [A.B.C.D/<0-32>]}

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show ip igmp group-ext


show ip igmp group-ext

Displays IGMP extended group details.

Syntax

show ip igmp group-ext {[count] | [group <A.B.C.D>] | [member-subnet [A.B.C.D/<0-32>] |

[source <A.B.C.D>]}

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show ip igmp interface


show ip igmp interface

Displays IGMP interface information.

Syntax

show ip igmp interface vlan <1-4094>

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show ip igmp profile


show ip igmp profile

Displays IGMP filter profiles.

Syntax

show ip igmp profile <1-65535>

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show ip igmp router-alert


show ip igmp router-alert

Displays router-alert settings.

Syntax

show ip igmp router-alert vlan <1-4094>

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show ip igmp snooping


show ip igmp snooping

Displays IGMP snooping information.

Syntax

show ip igmp snooping

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show ip igmp snoop-querier-addr


show ip igmp snoop-querier-addr

Displays IGMP snoop-querier-addr.

Syntax

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show ip ipfix


show ip ipfix

Displays global Internet Protocol Flow Information eXport (IPFIX) information.

Syntax

show ip ipfix

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip ipfix collector


show ip ipfix collector

Displays collector information.

Syntax

show ip ipfix collector

show ip ipfix collector {A.B.C.D}

Default

None

Command mode

User EXEC

Command parameters

Parameter Description{A.B.C.D} Specifies the collector IP address.



Avaya.com/support


Command: show ip ipfix interface


show ip ipfix interface

View Internet Protocol Flow Information eXport (IPFIX) information for an interface to see the sampling rate and the IPFIXadministrative status for the interface.

Syntax

show ip ipfix interface

show ip ipfix interface <port>

Default

None

Command mode

User EXEC

Command parameters





Avaya.com/support


Command: show ip ipfix slot


show ip ipfix slot

Displays IPFIX per-slot/unit settings.

Syntax

show ip ipfix slot <slot>

Default

None

Command mode

User EXEC

Command parameters

Parameter Description<slot> Specifies the slot number. Enter 1 for a standalone unit.



Avaya.com/support


Command: show ip ipfix table


show ip ipfix table

Displays IPFIX table.

Syntax

show ip ipfix table sort-by {byte-count | dest-addr | first-pkt-time | last-pkt-time |

pkt-count | port | protocol | source-addr | TCP-UDP-dest-port | TCP-UDP-scr-port | TOS}

sort-order {ascending | descending} display {all | top-10 | top-100 | top-200 | top-25 |

top-50}

Default

None

Command mode

User EXEC

Command parameters


display {all | top-10 | top-100 | top-200 | top-25 | top-50}

Specifies thenumber of entriesto display in theoutput.

sort-by {byte-count | dest-addr | first-pkt-time | last-pkt-time | pkt-count | port | protocol | source-addr | TCP-UDP-dest-port | TCP-UDP-scr-port | TOS}

Configures the sortrule

sort-order {ascending | descending} Configures the sortorder.



Avaya.com/support


Command: show ip mgmt


show ip mgmt

Displays management information.

Syntax

show ip mgmt

show ip mgmt all

show ip mgmt route

show ip mgmt switch

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionall Displays the management IP address for all units in the stack.route Displays management VLAN information.switch Displays the management IP address for the switch.



Avaya.com/support


Command: show ipmgr


show ipmgr

Displays IP Manager settings.

Syntax

show ipmgr

show ipmgr IPv4

show ipmgr IPv6

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter DescriptionIPv4 Shows only IPv4 information.IPv6 Shows only IPv6 information.



Avaya.com/support


Command: show ip netstat


show ip netstat

Displays IP TCP and UDP connections and services.

Syntax

show ip netstat

show ip netstat tcp

show ip netstat udp

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptiontcp Show IP TCP connections and services.udp Show IP UDP endpoints.



Avaya.com/support


Command: show ip ospf


show ip ospf

Displays OSPF configuration information.

Syntax

show ip ospf

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip ospf accept


show ip ospf accept

Displays information about the configured OSPF entries.

Syntax

show ip ospf accept

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip ospf area


show ip ospf area

Displays OSPF area configuration.

Syntax

show ip ospf area

show ip ospf area {A.B.C.D}

Default

None

Command mode

User EXEC

Command parameters

Parameter Description{A.B.C.D} Specifies the area ID.



Avaya.com/support


Command: show ip ospf area-range


show ip ospf area-range

Displays OSPF area range configuration.

Syntax

show ip ospf area-range

show ip ospf area-range {A.B.C.D}

Default

None

Command mode

User EXEC

Command parameters

Parameter Description{A.B.C.D} Specifies the area ID.



Avaya.com/support


Command: show ip ospf ase


show ip ospf ase

Displays AS External link state advertisements.

Syntax

show ip ospf ase

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip ospf authentication


show ip ospf authentication

Displays interface MD5 keys.

Syntax

show ip ospf authentication interface

show ip ospf authentication interface <port>

show ip ospf authentication interface Ethernet

show ip ospf authentication interface Ethernet <port>

show ip ospf authentication interface vlan

show ip ospf authentication interface vlan <1-4094>

show ip ospf authentication virtual-links

Default

None

Command mode

User EXEC

Command parameters


<port> Specifies the port in one of the following formats: a single port (3), a range of ports(3-4), or a series of ports (3,5,6).

interfaceEthernet

Displays only Ethernet IEEE 802.3 interfaces.

interfacevlan

Displays VLAN interfaces only.

virtual-links

Displays configured OSPF virtual link timer values.

vlan <1-4094>

Specifies a VLAN ID.



Avaya.com/support


Command: show ip ospf default-cost


show ip ospf default-cost

Displays default metric settings.

Syntax

show ip ospf default-cost

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip ospf host-route


show ip ospf host-route

Displays OSPF host routes.

Syntax

show ip ospf host-route

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip ospf ifstats


show ip ospf ifstats

Displays interface statistics.

Syntax

show ip ospf ifstats

show ip ospf ifstats {A.B.C.D}

show ip ospf ifstats detail

show ip ospf ifstats mismatch

Default

None

Command mode

User EXEC

Command parameters

Parameter Description{A.B.C.D} Specifies the interface IP address.detail Displays detailed information.mismatch Displays information if the area ID was not matched.



Avaya.com/support


Command: show ip ospf int-auth


show ip ospf int-auth

Displays interface authentication information.

Syntax

show ip ospf int-auth

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip ospf interface


show ip ospf interface

Displays interface configuration.

Syntax

show ip ospf interface

show ip ospf interface enabled

show ip ospf interface vlan

show ip ospf interface vlan <1-4094>

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionenabled Displays enabled OSPF interfaces.vlan <1-4094> Specifies a VLAN ID.



Avaya.com/support


Command: show ip ospf int-timers


show ip ospf int-timers

Displays timer settings of all interfaces.

Syntax

show ip ospf int-timers

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip ospf lsdb


show ip ospf lsdb

Displays the OSPF link state database.

Syntax

show ip ospf lsdb

show ip ospf lsdb adv-rtr {A.B.C.D}

show ip ospf lsdb area {A.B.C.D}

show ip ospf lsdb detail

show ip ospf lsdb lsa-type <as-external-link | as-summary-link | multicast-link |network-

link | nssa-extlink |router-link | summary-link>

show ip ospf lsdb lsid {A.B.C.D}

Default

None

Command mode

User EXEC

Command parameters


adv-rtr {A.B.C.D} Specifries theadvertising router.

area {A.B.C.D} Specifies the area.

detail {A.B.C.D} Displays detailedLSDB information.

lsa-type <as-external-link | as-summary-link | multicast-link |network-link | nssa-extlink |router-link | summary-link>

Specifies a linkstate advertismenttype.

lsid {A.B.C.D} Specifies a linkstate ID.



Avaya.com/support


Command: show ip ospf neighbor


show ip ospf neighbor

Displays OSPF neighbors.

Syntax

show ip ospf neighbor

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip ospf redistribute


show ip ospf redistribute

Displays OSPF redistribution policy.

Syntax

show ip ospf redistribute

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip ospf stats


show ip ospf stats

Displays global statistics.

Syntax

show ip ospf stats

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip ospf timer


show ip ospf timer

Displays interface timer settings.

Syntax

show ip ospf timer interface

show ip ospf timer interface vlan

show ip ospf timer interface vlan <1-4094>

show ip ospf timer virtual-links

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptioninterface Displays interface timer settings.virtual-links Displays configured OSPF virtual link timer values.vlan <1-4094> Specifies a Layer 3 IP VLAN.



Avaya.com/support


Command: show ip ospf virtual-link


show ip ospf virtual-link

Displays virtual links configuration.

Syntax

show ip ospf virtual-link

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip ospf virtual-neighbors


show ip ospf virtual-neighbors

Displays OSPF virtual link neighbors.

Syntax

show ip ospf virtual-neighbors

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip prefix-list


show ip prefix-list

Displays prefix list information.

Syntax

show ip prefix-list

show ip prefix-list <WORD>

show ip prefix-list prefix {A.B.C.D}

Default

None

Command mode

User EXEC

Command parameters

Parameter Description<WORD> Specifies the name of the prefix list.prefix {A.B.C.D} Specifies the IP prefix list.



Avaya.com/support


Command: show ip rip


show ip rip

Displays RIP configuration information.

Syntax

show ip rip

show ip rip interface

show ip rip interface <1-4094>

show ip rip interface enabled

show ip rip interface Ethernet

show ip rip interface Ethernet <port>

show ip rip interface vlan

show ip rip stats

Default

None

Command mode

User EXEC

Command parameters

Parameter Description<1-4094> Specifies a VLAN ID.


enabled Displays only enabled RIP interfaces.Ethernet Displays only Ethernet IEEE 802.3 interfaces.stats Displays RIP statistics.vlan Displays VLAN interfaces only.



Avaya.com/support


Command: show ip route


show ip route

Displays the IP route information.

Syntax

show ip route

show ip route -s <A.B.C.D> <A.B.C.D>

show ip route <ospf|rip|static>

show ip route <ospf|rip|static> -s <A.B.C.D> <A.B.C.D>

show ip route <ospf|rip|static> <A.B.C.D>

show ip route summary

Default

None

Command mode

User EXEC

Command parameters

Parameter Description-s <A.B.C.D> <A.B.C.D> Indicates the IP address and subnet mask for which to display routes.<A.B.C.D> Specifies the IP address of the route.<ospf|rip|static> Displays IP route information for a specific type of route.summary Displays a summary of IP route information.



Avaya.com/support


Command: show ip routing


show ip routing

Displays the IP routing configuration information.

Syntax

show ip routing

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip source-interface


show ip source-interface

Displays which applications a CLIP is assigned as the source IP address.

Syntax

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ipv6 address


show ipv6 address

Displays configured IPv6 addresses.

Syntax

show ipv6 address

show ipv6 address interface

show ipv6 address interface <WORD>

show ipv6 address interface summary

show ipv6 address interface vlan <1-4094>

show ipv6 address stack

show ipv6 address switch

show ipv6 address unit <1-8>

Default

None

Command mode

User EXEC

Command parameters

Parameter Description<WORD> Specifies the IPv6 address.interface Displays addresses for IPv6 interfaces.stack Displays the IPv6 address of the stack.summary Displays an IPv6 interface summary.switch Displays the IPv6 address of the local unit.unit <1-8> Displays the IPv6 address of another unit in a stack.vlan <1-4094> Displays VLAN addresses for IPv6 interfaces.



Avaya.com/support


Command: show ipv6 default-gateway


show ipv6 default-gateway

Displays IPv6 default gateway information.

Syntax

show ipv6 default-gateway

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ipv6 default-routers(Privileged Executive)


show ipv6 default-routers (Privileged Executive)

Displays IPv6 default routers configuration.

Syntax

Default

None

Command mode




Avaya.com/support


Command: show ipv6 default-routers(User Executive)


show ipv6 default-routers (User Executive)

Displays IPv6 default routers configuration.

Syntax

Default

None

Command mode

User Executive



Avaya.com/support


Command: show ipv6 destinationcache(Privileged Executive)


show ipv6 destinationcache (Privileged Executive)

Displays IPv6 destination cache information.

Syntax

Default

None

Command mode




Avaya.com/support


Command: show ipv6 destinationcache(User Executive)


show ipv6 destinationcache (User Executive)

Displays IPv6 destination cache information.

Syntax

Default

None

Command mode

User Executive



Avaya.com/support


Command: show ipv6 dhcp-relay


show ipv6 dhcp-relay

Displays IPv6 Dynamic Host Configuration Protocol (DHCP) Relay information to show relay information about DHCP routes andcounters.

Syntax

show ipv6 dhcp-relay counters

show ipv6 dhcp-relay fwd-path

show ipv6 dhcp-relay interface

show ipv6 dhcp-relay interface vlan <1-4094>

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptioncounters Displays the count of DHCP Relay requests and replies.fwd-path Displays information about DHCP Relay forward paths.interface Displays information about DHCP Relay interfaces.interface vlan <1-4084> Specifies the VLAN ID.



Avaya.com/support


Command: show ipv6 global


show ipv6 global

Displays global IPv6 configuration information.

Syntax

show ipv6 global

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ipv6 interface


show ipv6 interface

Displays IPv6 information for all or specific interfaces.

Syntax

show ipv6 interface

show ipv6 interface loopback <1-16>

show ipv6 interface vlan <1-4094>

show ipv6 interface icmpstatistics mgmt

show ipv6 interface icmpstatistics tunnel <1-2147483647>

show ipv6 interface icmpstatistics vlan <1-4094>

show ipv6 interface statistics

show ipv6 interface statistics mgmt

show ipv6 interface statistics tunnel <1-2147483647>

show ipv6 interface statistics vlan <1-4094>

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionloopback <1-16> Displays per loopback IPv6 interfaces.vlan <1-4094> Displays per vlan IPv6 interfaces.icmpstatistics Displays IPv6 ICMP statistics.process-redirect Displays IPv6 processing redirect.statistics Displays IPv6 statistics.mgmt Displays information by management interface.statistics Displays IPv6 statistics.tunnel <1-2147483647> Displays information by tunnel.



Command: show ipv6 mgmt


show ipv6 mgmt

Displays IPv6 management information.

Syntax

show ipv6 mgmt address

show ipv6 mgmt address unit <1-8>

show ipv6 mgmt default-gateway

show ipv6 mgmt interface [process-redirect]

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionaddress Displays IPv6 management addresses.default-gateway Displays IPv6 management gateway.interface Displays IPv6 management interfaces.unit <1-8> Specifies the unit number in stack mode.



Avaya.com/support


Command: show ipv6 mld-host-cache


show ipv6 mld-host-cache

Displays the learned multicast groups in the host cache.

Syntax

show ipv6 mld-host-cache [interface <1-4094>]

Default

None

Command mode

User Executive

Command parameters

Parameter Descriptioninterface <1-4094> Displays by VLAN.



Avaya.com/support


Command: show ipv6 mld-host-cache(Privileged Executive)


show ipv6 mld-host-cache (Privileged Executive)

Displays the learned multicast groups in the host cache.

Syntax

Default

None

Command mode


Command parameters

Parameter Descriptioninterface <1-4094> Displays by VLAN.



Avaya.com/support


Command: show ipv6 nd


show ipv6 nd

Displays neighbor discovery interface configuration.

Syntax

show ipv6 nd interface <1-4094>

show ipv6 nd interface details

show ipv6 nd interface vlan

Default

None

Command mode

User EXEC

Command parameters

Parameter Description<1-4094> Specifies a VLAN ID.details Shows detailed information.vlan Shows addresses on VLAN interfaces only.



Avaya.com/support


Command: show ipv6 nd-prefix


show ipv6 nd-prefix

Displays configured neighbor discovery prefixes.

Syntax

show ipv6 nd-prefix interface

show ipv6 nd-prefix interface <1-4094>

show ipv6 nd-prefix interface details

show ipv6 nd-prefix interface vlan

Default

None

Command mode

User EXEC

Command parameters

Parameter Description<1-4094> Specifies a VLAN ID.details Shows detailed information.vlan Shows addresses on VLAN interfaces only.



Avaya.com/support


Command: show ipv6 neighbor


show ipv6 neighbor

Displays entries in the neighbor cache.

Syntax

show ipv6 neighbor

show ipv6 neighbor <WORD>

show ipv6 neighbor interface mgmt

show ipv6 neighbor interface tunnel

show ipv6 neighbor interface tunnel <1-2147483647>

show ipv6 neighbor interface vlan

show ipv6 neighbor interface vlan <1-4094>

show ipv6 neighbor summary

show ipv6 neighbor type <dynamic|local|other|static>

Default

None

Command mode

User EXEC

Command parameters

Parameter Description<WORD> Specifies an IPv6 address.

interface mgmt Displays neighbor information by out-of-bandmanagement.

interface tunnel <1-2147483647> Displays neighbor information by tunnel.interface vlan <1-4094> Displays neighbor information by VLAN.summary Displays a summary of the neighbor cache.type<dynamic|local|other|static>

Displays neighbor information by neighbor type.



Avaya.com/support


Command: show ipv6 route


show ipv6 route

Displays IPv6 routes for the switch.

Syntax

show ipv6 route

show ipv6 route dest <WORD>

show ipv6 route mgmt

show ipv6 route next-hop <WORD>

show ipv6 route static

show ipv6 route tunnel <1-2147483647>

show ipv6 route vlan <1-4094>

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptiondest <WORD> Shows the route to a specific IPv6 address.mgmt Shows route entries for out-of-band management.next-hop <WORD> Shows the route to a specific IPv6 next hop.static Shows static IPv6 routes.tunnel <1-2147483647> Shows route entries for a specific tunnel ID.vlan <1-4094> Shows route entries for a specific VLAN ID.



Avaya.com/support


Command: show ipv6 tcp


show ipv6 tcp

Displays IPv6 TCP information. Check the health of connections, from the switch perspective, as they traverse the network; detectintermittent connectivity; detect attacks on resources; determine which applications are active by checking the port numbers.

Syntax

show ipv6 tcp

show ipv6 tcp connections

show ipv6 tcp listener

Default

None

Command mode

User EXEC

Command parameters


connections Displays IPv6 TCP connection table information that includes: local port, remote port,local address, remote address, and state.

listener Displays IPv6 TCP listener table information that includes: local port and local address.



Avaya.com/support


Command: show ipv6 tunnel


show ipv6 tunnel

Shows information about configured IPv6 tunnels, for example, operational state or addresses.

Syntax

show ipv6 tunnel

show ipv6 tunnel <1-2147483647>

Default

None

Command mode

User EXEC

Command parameters

Parameter Description<1-2147483647> Shows configuration information for a specific tunnel ID.



Avaya.com/support


Command: show ipv6 udp


show ipv6 udp

Show IPv6 User Datagram Protocol (UDP) information.

Syntax

show ipv6 udp

show ipv6 udp endpoints

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionendpoints Shows IPv6 UDP information for the endpoints.



Avaya.com/support


Command: show ip vrrp


show ip vrrp

Displays the global Virtual Router Redundancy Protocol (VRRP) configuration.

Syntax

show ip vrrp

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ip vrrp address


show ip vrrp address

Displays basic Virtual Router Redundancy Protocol (VRRP) configuration information about the specified port, all ports, or theVLAN.

Syntax

show ip vrrp address

show ip vrrp address addr {A.B.C.D}

show ip vrrp address interface

show ip vrrp address interface <1-4094>

show ip vrrp address interface addr {A.B.C.D}

show ip vrrp address interface vlan

show ip vrrp address interface vrid <1-255>

show ip vrrp address vrid

show ip vrrp address vrid <1-255>

Default

None

Command mode

User EXEC

Command parameters

Parameter Description<1-4094> Specifies a VLAN ID.addr {A.B.C.B} Displays a specific address.interface Displays addresses per interface.vlan Displays addresses on VLAN interfaces only.vrid <1-255> Display saddresses associated with specific VR.



Avaya.com/support


Command: show ip vrrp interface


show ip vrrp interface

Displays Virtual Router Redundancy Protocol (VRRP) information about the interface.

Syntax

show ip vrrp interface

show ip vrrp interface <vlan ID>

show ip vrrp interface verbose

show ip vrrp interface vlan

show ip vrrp interface vrid <1-255>

Default

None

Command mode

User EXEC

Command parameters

Parameter Description<vlan ID> Specifies a VLAN ID.verbose Displays additional information.vlan Displays addresses on VLAN interfaces only.vrid <1-255> Specifies a virtual router ID.



Avaya.com/support


Command: show i-sid


show i-sid

Display I-SID information.

Syntax

show i-sid

show i-sid <1-16777214>

Default

None

Command mode

User EXEC

Command parameters

Parameter Description<1-16777214> Specifies a particular I-SID by ID.



Avaya.com/support


Command: show isis adjacencies


show isis adjacencies

Displays Intermediate-System-to-Intermediate-System (IS-IS) adjacencies.

Syntax

show isis adjacencies

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show isis int-auth


show isis int-auth

Displays the Intermediate-System-to-Intermediate-System (IS-IS) interface authentication configuration.

Syntax

show isis int-auth

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show isis int-ckt-level


show isis int-ckt-level

Displays the Intermediate-System-to-Intermediate-System (IS-IS) circuit level parameters.

Syntax

show isis int-ckt-level

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show isis int-counters


show isis int-counters

Displays Intermediate-System-to-Intermediate-System (IS-IS) interface counters.

Syntax

show isis int-counters

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show isis interface


show isis interface

Displays Intermediate-System-to-Intermediate-System (IS-IS) interface configuration and status parameters (includingadjacencies).

Syntax

show isis interface

show isis interface l1

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionl1 Displays the interface information for the specified level.



Avaya.com/support


Command: show isis int-l1-cntl-pkts


show isis int-l1-cntl-pkts

Displays Intermediate-System-to-Intermediate-System (IS-IS) Level 1 control packet counters.

Syntax

show isis int-l1-cntl-pkts

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show isis int-timers


show isis int-timers

Displays Intermediate-System-to-Intermediate-System (IS-IS) interface timers.

Syntax

show isis int-timers

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show isis lsdb


show isis lsdb

Displays the Intermediate-System-to-Intermediate-System (IS-IS) Link State Database (LSDB).

Syntax

show isis lsdb

show isis lsdb detail

show isis lsdb level l1

show isis lsdb lspid <WORD>

show isis lsdb sysid <H.H.H>

show isis lsdb tlv <WORD>

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptiondetail Displays details.level l1 Displays the link state database for the specified level.lsp-id<WORD>

Displays the link state database for the specified Link State Packet (LSP) ID. The LSP IDis assigned to external IS-IS routing devices.

sysid<H.H.H>

Displays the link state database for the specified system ID.

tlv<WORD>

Displays the link state database for a specified Type-Length-Value (TLV). Enter the TLVtype: 1(Area Addresses), 3(End System Neighbors), 5(Prefix Neighbors), 22(TENeighbors), 128(IP Addresses), 129(Protocol Supported), 135(TE IP Reachability),144(Multi Topology)



Avaya.com/support


Command: show isis manual-area


show isis manual-area

Displays Intermediate-System-to-Intermediate-System (IS-IS) areas.

Syntax

show isis manual-area

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show isis net


show isis net

Displays Intermediate-System-to-Intermediate-System (IS-IS) net information.

Syntax

show isis net

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show isis spbm i-sid


show isis spbm i-sid

Displays the Intermediate-System-to-Intermediate-System (IS-IS) Shortest Path Bridging MAC (SPBM) multicast ForwardingInformation Base (FIB) calculation results by service instance identifier (I-SID).

Syntax

show isis spbm i-sid { all | config | discover }

show isis spbm i-sid { all | config | discover } id <1-16777215>

show isis spbm i-sid { all | config | discover } nick-name <WORD>

show isis spbm i-sid { all | config | discover } vlan <0-4094>

Default

None

Command mode

User EXEC

Command parameters

Parameter Description{ all | config| discover }

all: Displays all service instance identifier (I-SID) entries; config: Displays theconfigured I-SID entries; and discover: Displays discovered I-SID entries.

id <1-16777215>

Displays service instance identifier (I-SID) information for the specified I-SID.

nick-name<WORD>

Displays service instance identifier (I-SID) information for the specified nick-name.

vlan <0-4094> Displays service instance identifier (I-SID) information for the specified ShortestPath Bridging MAC (SPBM) VLAN.



Avaya.com/support


Command: show isis spbm multicast-fib


show isis spbm multicast-fib

Displays the Intermediate-System-to-Intermediate-System (IS-IS) Shortest Path Bridging MAC (SPBM) multicast ForwardingInformation Database (FIB) entries.

Syntax

show isis spbm multicast-fib

show isis spbm multicast-fib i-sid <1-16777214>

show isis spbm multicast-fib nick-name <WORD>

show isis spbm multicast-fib summary

show isis spbm multicast-fib vlan <0-4094>

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptioni-sid <1-16777214>

Displays the Forwarding Information Base (FIB) entry for the specified serviceinstance identifier (I-SID).

nick-name<WORD>

Displays the Forwarding Information Base (FIB) entry for the specified nick-name.

summary Displays a summary of the Forwarding Information Base (FIB).vlan <0-4094>

Displays the Forwarding Information Base (FIB) entry for the specified ShortestPath Bridging MAC (SPBM) VLAN.



Avaya.com/support


Command: show isis spbm nick-name


show isis spbm nick-name

Displays the Shortest Path Bridging MAC (SPBM) configurations for a specific nick-name.

Syntax

show isis spbm nick-name

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show isis spbm unicast-fib


show isis spbm unicast-fib

Displays the Shortest Path Bridging MAC (SPBM) unicast Forwarding Information Base (FIB).

Syntax

show isis spbm unicast-fib

show isis spbm unicast-fib b-mac <H.H.H.>

show isis spbm unicast-fib summary

show isis spbm unicast-fib vlan <0-4094>

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionb-mac<H.H.H>

Displays the Forwarding Information Base (FIB) entry for the specified Backbone MAC(BMAC).

summary Displays a summary of the Forwarding Information Base (FIB).vlan <0-4094>

Displays the Forwarding Information Base (FIB) entry for the specified Shortest PathBridging MAC (SPBM) VLAN.



Avaya.com/support


Command: show isis spbm unicast-tree


show isis spbm unicast-tree

Displays the Shortest Path Bridging MAC (SPBM) unicast tree.

Syntax

show isis spbm unicast-tree <1-4094>

show isis spbm unicast-tree <1-4094> destination <H.H.H>

Default

None

Command mode

User EXEC

Command parameters

Parameter Description<1-4094> Specifies the VLAN ID.destination <H.H.H> Specifies the destination B-MAC.



Avaya.com/support


Command: show isis statistics


show isis statistics

Displays Intermediate-System-to-Intermediate-System (IS-IS) statistics.

Syntax

show isis statistics

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show isis system-id


show isis system-id

Displays Intermediate-System-to-Intermediate-System (IS-IS) system ID.

Syntax

show isis system-id

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ist


show ist

Displays Inter Switch Trunk (IST) configuration.

Syntax

show ist

show ist stat

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionstat Displays IST statistics.



Avaya.com/support


Command: show jumbo-frames


show jumbo-frames

Displays jumbo frames support.

Syntax

show jumbo-frames

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show lacp aggr


show lacp aggr

Displays LACP aggregator information.

Syntax

show lacp aggr

show lacp aggr <1-65535>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<1-65535> Specifies the aggregator ID.



Avaya.com/support


Command: show lacp debug


show lacp debug

Displays LACP port debug information.

Syntax

show lacp debug member

show lacp debug member <WORD>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionmember <WORD> Specifies a port or list of ports.



Avaya.com/support


Command: show lacp key


show lacp key

Displays MLTs or MLTs/SMLTs reserved for LACP key values.

Syntax

show lacp key

show lacp key <1-4095>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<1-4095> Specifies the LACP key value.



Avaya.com/support


Command: show lacp port


show lacp port

Displays LACP port information.

Syntax

show lacp port

show lacp port <WORD>

show lacp port aggr <1-65535>

show lacp port key <1-4095>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<WORD> Specifies a port or list of ports.aggr <1-65535> Specifies the aggregator ID.key <1-4095> Specifies the LACP key value.



Avaya.com/support


Command: show lacp port-mode


show lacp port-mode

Displays current LACP port mode settings.

Syntax

show lacp port-mode

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show lacp stats


show lacp stats

Displays LACP statistics information.

Syntax

show lacp stats

show lacp stats <WORD>

show lacp stats aggr <1-65535>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<WORD> Specifies a port or list of ports.aggr <1-65535> Specifies the aggregator ID.



Avaya.com/support


Command: show lacp system


show lacp system

Displays LACP system settings.

Syntax

show lacp system

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show link-state


show link-state

Displays link-state tracking configuration.

Syntax

show link-state

show link-state detail

show link-state group <1-2>

show link-state group <1-2> detail

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptiondetail Displays detailed configuration information.group <1-2> Displays link-state tracking configuration for a specific group.



Avaya.com/support


Command: show lldp


show lldp

Displays 802.1ab settings.

Syntax

show lldp

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show lldp local-sys-data


show lldp local-sys-data

Displays 802.1ab local system data.

Syntax

show lldp local-sys-data

show lldp local-sys-data detail

show lldp local-sys-data med

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptiondetail Displays all TLVs.med Displays Media Endpoint Devices (MED) specific TLVs.



Avaya.com/support


Command: show lldp med-network-policies


show lldp med-network-policies

Displays Media Endpoint Devices (MED) network policies.

Syntax

show lldp med-network-policies

show lldp med-network-policies port <port>

show lldp med-network-policies voice

show lldp med-network-policies voice-signaling

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionport<port>

Specifies the port in one of the following formats: a single port (3), a range of ports(3-4), or a series of ports (3,5,6).

voice Displays voice network policies.voice-signaling

Displays voice signaling network policies.



Avaya.com/support


Command: show lldp mgmt-sys-data


show lldp mgmt-sys-data

Displays 802.1ab management data.

Syntax

show lldp mgmt-sys-data

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show lldp neighbor


show lldp neighbor

Displays 802.1ab neighbors.

Syntax

show lldp neighbor

show lldp neighbor detail

show lldp neighbor med

show lldp neighbor med capabilities

show lldp neighbor med extended-power

show lldp neighbor med inventory

show lldp neighbor med location

show lldp neighbor med network-policy

show lldp neighbor vendor-specific avaya

show lldp neighbor vendor-specific avaya call-server

show lldp neighbor vendor-specific avaya dot1q-framing

show lldp neighbor vendor-specific avaya file-server

show lldp neighbor vendor-specific avaya phone-ip

show lldp neighbor vendor-specific avaya poe-conservation

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptioncall-server Displays neighbors call-server information.capabilities Displays neighbors MED capabilities.detail Displays all TLVs.dot1q-framing Displays neighbors dot1q-framing information.

extended-power Displays neighbors MED power information.file-server Displays neighbors file-server information.inventory Displays neighbors MED inventory information.location Displays neighbors MED location information.med Displays MED specific TLVs.network-policy Displays neighbors MED network-policy information.phone-ip Displays neighbors phone-ip information.poe-conservation Displays neighbors poe-conservation information.vendor-specific Displays the vendor-specific TLVs.



Avaya.com/support


Command: show lldp neighbor-mgmt-addr


show lldp neighbor-mgmt-addr

Displays 802.1ab neighbors management addresses.

Syntax

show lldp neighbor-mgmt-addr

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show lldp pdu-tlv-size


show lldp pdu-tlv-size

Displays 802.1ab TLVs in PDU.

Syntax

show lldp pdu-tlv-size

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show lldp port


show lldp port

Displays 802.1ab configuration for specified ports. You can append other LLDP parameters to the end of this command to viewLLDP information for specific ports, similar to other show lldp commands that show information for all ports simulatenously.

Syntax

show lldp port <port>

Default

None

Command mode

User EXEC

Command parameters


port Specifies the port in one of the following formats: a single port (3), a range of ports (3-4), or a series of ports (3,5,6).



Avaya.com/support


Command: show lldp rx-stats


show lldp rx-stats

Displays 802.1ab receive statistics.

Syntax

show lldp rx-stats

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show lldp stats


show lldp stats

Displays 802.1ab statistics.

Syntax

show lldp stats

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show lldp tx-stats


show lldp tx-stats

Displays 802.1ab transmit statistics.

Syntax

show lldp tx-stats

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show lldp tx-tlv


show lldp tx-tlv

Displays 802.1ab TLVs.

Syntax

show lldp tx-tlv

show lldp tx-tlv med

show lldp tx-tlv vendor-specific avaya

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionmed Displays Media Endpoint Devices (MED) specific TLVs.vendor-specific avaya Displays vendor-specific TLVs.



Avaya.com/support


Command: show lldp vendor-specificavaya


show lldp vendor-specific avaya

Displays 802.1ab vendor-specific settings.

Syntax

show lldp vendor-specific avaya call-server

show lldp vendor-specific avaya dot1q-framing

show lldp vendor-specific avaya file-server

show lldp vendor-specific avaya poe-conservation-request-level

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptioncall-server Displays call-server addresses.dot1q-framing Displays 802.1Q framing tragging-mode.file-server Displays file-server addresses.poe-conservation-request-level Displays PoE conservation request level.



Avaya.com/support


Command: show logging


show logging

Displays the contents of the logging buffers.

Syntax

show loggin unit <1-8>

show logging

show logging config

show logging critical [sort-reverse] [unit<1-8>]

show logging informational [sort-reverse] [unit<1-8>]

show logging serious [sort-reverse] [unit<1-8>]

show logging sort-reverse

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionconfig Displays configuration of event logging.critical Displays critical events.informational Displays informational messages.serious Displays serious event messages.sort-reverse Displays log messages in reverse order.unit <1-8> Displays log messages by unit number.



Avaya.com/support


Command: show mac-address-table


show mac-address-table

Displays forwarding database tables.

Syntax

show mac-address-table

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show mac-address-tableaddress


show mac-address-table address

Displays a specific address.

Syntax

show mac-address-table address <H.H.H>

Default

None

Command mode

Privileged EXEC

Command parameters


<H.H.H> Specifies the address to be displayed (i.e. H.H.H or xx.xx.xx.xx.xx.xx or xx-xx-xx-xx-xx-xxor xx:xx:xx:xx:xx:xx)



Avaya.com/support


Command: show mac-address-tableaging-time


show mac-address-table aging-time

Displays forwarding database aging time.

Syntax

show mac-address-table aging-time

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show mac-address-tabledynamic


show mac-address-table dynamic

Displays only dynamically learned addresses.

Syntax

show mac-address-table dynamic

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show mac-address-table mlt


show mac-address-table mlt

Displays the mac-address-table for a specified trunk ID.

Syntax

show mac-address-table mlt <1-64>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<1-64> Specifies the MLT ID.



Avaya.com/support


Command: show mac-address-tableport


show mac-address-table port

Displays the mac-address-table for specified ports.

Syntax

show mac-address-table port <port>

Default

None

Command mode

Privileged EXEC

Command parameters




Avaya.com/support


Command: show mac-address-tablespbm


show mac-address-table spbm

Displays SPBM MAC entries.

Syntax

show mac-address-table spbm [i-sid <1-16777215>]

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptioni-sid <1-16777215> Displays SPBM MAC entries for the specified i-sid.



Avaya.com/support


Command: show mac-address-tablestatic


show mac-address-table static

Displays only statically inserted addresses.

Syntax

show mac-address-table static

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show mac-address-table vid


show mac-address-table vid

Displays the mac-address-table for a specified VLAN ID.

Syntax

show mac-address-table vid <1-4094>

Default

None

Command mode

Privileged EXEC

Command parameters




Avaya.com/support


Command: show mac-security


show mac-security

Displays current MAC address security settings.

Syntax

show mac-security config

show mac-security mac-address-table [address <H.H.H>] [port <port>]

show mac-security mac-da-filter

show mac-security port <port>

show mac-security security-lists <LINE>}

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionaddress <H.H.H> Displays the accessible port for specific MAC address.config Displays the stack or switch MAC security configuration.mac-address-table Displays the accessible MAC addresses on each port.mac-da-filter Displays MAC DA filtering addresses.port Displays the MAC security status for a port.port <port> Displays MAC addresses from specific port.security-lists <LINE> Displays port membership of security lists.



Avaya.com/support


Command: show mda


show mda

Displays information about the media dependent adapater (MDA).

Syntax

show mda

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show memory-utilization


show memory-utilization

Displays memory utilization information.

Syntax

show memory-utilization

show memory-utilization unit <1-8>

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionunit <1-8> Specifies the unit number in stack mode.



Avaya.com/support


Command: show mgmt-port status


show mgmt-port status

Displays management port information.

Syntax

show mgmt-port status

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show mlt


show mlt

Displays MultiLink Trunking (MLT) information.

Syntax

show mlt

show mlt shutdown-ports-on-disable

show mlt <line>

show mlt disabled

show mlt enabled

show mlt spanning-tree <1-64>

show mlt utilization <1-64>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<line> Specifies a list of trunk groups.disabled Shows disabled MLTs.enabled Shows enables MLTs.shutdown-ports-on-disable Displays the status of disabled trunk loop prevention.spanning-tree <1-64> Displays MLT spanning-tree group and learning information.utilization <1-64> Displays MLT utilization information.



Avaya.com/support


Command: show mlt hash-calc


show mlt hash-calc

Displays MLT hash calculations.

Syntax

show mlt hash-calc <1-64> dest-ip <A.B.C.D |WORD> src-ip <A.B.C.D> tcp-udp-dport <0-65535>

tcp-udp-sport <0-65535>

show mlt hash-calc <1-64> dest-mac <H.H.H> src-mac <H.H.H> vlan <1-4094> ethertype

<0x0600-0xffff> src-port <WORD>

show mlt hash-calc <1-64> non-unicast dest-mac <H.H.H> src-mac <H.H.H> src-port <WORD>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<1-64> Specifies the MLT ID.dest-ip<A.B.C.D|WORD>

Specifies the IPv4 or IPv6 address of the destination switch.

dest-mac<H.H.H>

Specifies the MAC address of the destination switch.

ethertype<0x0600-0xffff>

Specifies the Ethertype value as a decimal or hexadecimal value. Values rangefrom 8101 to 81FF hexadecimal, or 33025 to 36479 decimal.

non-unicast Indicates the non-unicast algorithm for which to display load balancinginformation.

src-ip<A.B.C.D>

Specifies the IPv4 or IPv6 address of the source switch.

src-mac<H.H.H>

Specifies the MAC address of the source switch.

src-port<WORD>

Specifies the slot and port number of the source switch.

tcp-udp-dport<0-65535>

Specifies the destination TCP/UDP port number.

tcp-udp-sport<0-65535>

Specifies the source TCP/UDP port number.

vlan <1-4094> Specifies a VLAN ID.



Avaya.com/support


Command: show ntp


show ntp

Displays the Network Time Protocol (NTP) server status statistics.

Syntax

show ntp

show ntp server

show ntp statistics

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionserver Specifies to show NTP server information.statistics Specifies to show NTP statistics information.



Avaya.com/support


Command: show nvram block


show nvram block

Displays NV block information.

Syntax

show nvram block

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show password


show password

Displays password security restrictions.

Syntax

show password aging-time

show password aging-time username <WORD>

show password password-history

show password security

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionaging-time Shows the validity period in days.password-history Shows the number of passwords in history.security Shows the state of password security restrictions.username <WORD> Shows the aging time for a particular username.



Avaya.com/support


Command: show port-mirroring


show port-mirroring

Displays the port mirroring configuration.

Syntax

show port-mirroring

show port-mirroring <1-4>

show port-mirroring rspan

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<1-4> Specifies an instance number.rspan Shows Remote Switch Port Analyzer (RSPAN) settings.



Avaya.com/support


Command: show port-statistics


show port-statistics

Displays port counters for a port.

Syntax

show port-statistics

show port-statistics port <port>

show port-statistics port mgmt

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionport <port> Displays statistics for a specific port or list of ports.port mgmt Displays statistics for the management port.



Avaya.com/support


Command: show qos action


show qos action

Displays the base action entries.

Syntax

show qos action

show qos action <1-65535>

show qos action all

show qos action system

show qos action user

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<1-65535> Display the specified base action entry.all Display all user-created, default, and system entries.system Display only system entries.user Display only user-created and default entries.



Avaya.com/support


Command: show qos agent


show qos agent

Displays the global QoS parameters.

Syntax

show qos agent

show qos agent details

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptiondetails Display agent details.



Avaya.com/support


Command: show qos capability


show qos capability

Displays QoS port capabilities.

Syntax

show qos capability meter

show qos capability meter port <port>

show qos capability shaper

show qos capability shaper port <port>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionmeter Display QoS port meter capabilities.port <port> Specifies a port or list of ports.shaper Display QoS port shaper capabilities.



Avaya.com/support


Command: show qos classifier


show qos classifier

Displays the classifier entries.

Syntax

show qos classifier

show qos classifier <1-65535>

show qos classifier all

show qos classifier system

show qos classifier user

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<1-65535> Display the specified classifier entry.all Display all user-created, default, and system entries.system Display only system entries.user Display only user-created and default entries.



Avaya.com/support


Command: show qos classifier-block


show qos classifier-block

Displays the classifier block entries.

Syntax

show qos classifier-block

show qos classifier-block <1-65535>

show qos classifier-block all

show qos classifier-block system

show qos classifier-block user

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<1-65535> Display the specified classifier block entry.all Display all user-created, default, and system entries.system Display only system entries.user Display only user-created and default entries.



Avaya.com/support


Command: show qos diag


show qos diag

Displays the diagnostics entries.

Syntax

show qos diag

show qos diag unit <1-8>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionunit <1-8> Specifies the unit number in a stack.



Avaya.com/support


Command: show qos egressmap


show qos egressmap

Displays the association between the DSCP and the 802.1p priority and drop precedence

Syntax

show qos egressmap

show qos egressmap ds <0-63>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionds <0-63> Show the mapping for one DSCP value.



Avaya.com/support


Command: show qos if-action-extension


show qos if-action-extension

Displays the interface action extension entries.

Syntax

show qos if-action-extension

show qos if-action-extension <1-65535>

show qos if-action-extension all

show qos if-action-extension system

show qos if-action-extension user

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<1-65535> Display the specified interface action extension entry.all Display all user-created, default, and system entries.system Display only system entries.user Display only user-created and default entries.



Avaya.com/support


Command: show qos if-assign


show qos if-assign

Displays the list of interface assignments.

Syntax

show qos if-assign

show qos if-assign port <port>

Default

None

Command mode

Privileged EXEC

Command parameters




Avaya.com/support


Command: show qos if-group


show qos if-group

Displays the interface groups.

Syntax

show qos if-group

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show qos if-queue-shaper


show qos if-queue-shaper

Displays the interface egress queue shaping parameters.

Syntax

show qos if-queue-shaper

show qos if-queue-shaper port <port>

Default

None

Command mode

Privileged EXEC

Command parameters




Avaya.com/support


Command: show qos if-shaper


show qos if-shaper

Displays the interface shaping parameters.

Syntax

show qos if-shaper

show qos if-shaper port <port>

Default

None

Command mode

Privileged EXEC

Command parameters




Avaya.com/support


Command: show qos ingressmap


show qos ingressmap

Displays the 802.1p priority to DSCP mapping.

Syntax

show qos ingressmap

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show qos ip-element


show qos ip-element

Displays the IP classifier element entries.

Syntax

show qos ip-element

show qos ip-element <1-65535>

show qos ip-element all

show qos ip-element system

show qos ip-element user

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<1-65535> Display the specified IP classifer element entry.all Display all user-created, default, and system entries.system Display only system entries.user Display only user-created and default entries.



Avaya.com/support


Command: show qos l2-element


show qos l2-element

Displays the Layer2 classifier element entries.

Syntax

show qos l2-element

show qos l2-element <1-65535>

show qos l2-element all

show qos l2-element system

show qos l2-element user

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<1-65535> Display the specified Layer 2 classifer element entry.all Display all user-created, default, and system entries.system Display only system entries.user Display only user-created and default entries.



Avaya.com/support


Command: show qos meter


show qos meter

Displays the meter entries.

Syntax

show qos meter

show qos meter <1-65535>

show qos meter all

show qos meter system

show qos meter user

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<1-65535> Display the specified meter entry.all Display all user-created, default, and system entries.system Display only system entries.user Display only user-created and default entries.



Avaya.com/support


Command: show qos policy


show qos policy

Displays the policy entries.

Syntax

show qos policy

show qos policy <1-65535>

show qos policy all

show qos policy port <port>

show qos policy system

show qos policy user

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<1-65535> Display the specified policy entry.all Display all user-created, default, and system entries.port <port> Specifies a port or list of ports.system Display only system entries.user Display only user-created and default entries.



Avaya.com/support


Command: show qos port


show qos port

Displays port QoS configuration.

Syntax

show qos port <port>

Default

None

Command mode

Privileged EXEC

Command parameters




Avaya.com/support


Command: show qos queue-set


show qos queue-set

Displays the queue set configuration.

Syntax

show qos queue-set

show qos queue-set <1-8>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<1-8> Display the specified queue-set.



Avaya.com/support


Command: show qos queue-set-assignment


show qos queue-set-assignment

Displays the association between the 802.1p priority to that of a specific queue.

Syntax

show qos queue-set-assignment

show qos queue-set-assignment queue-set <1-8>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionqueue-set <1-8> Display the specified queue-set.



Avaya.com/support


Command: show qos statistics


show qos statistics

Displays statistics values.

Syntax

show qos statistics <1-65535>

show qos statistics <1-65535> port <port>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<1-65535> Specifies a policy ID.<port> Specifies a port or list of ports.



Avaya.com/support


Command: show qos system-element


show qos system-element

Displays the system classifier element entries.

Syntax

show qos system-element

show qos system-element <1-65535>

show qos system-element all

show qos system-element system

show qos system-element user

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<1-65535> Display the specified system classifier element entry.all Display all user-created, default, and system entries.system Display only system entries.user Display only user-created and default entries.



Avaya.com/support


Command: show qos traffic-profile


show qos traffic-profile

Displays QoS traffic profile entries.

Syntax

show qos traffic-profile classifier

show qos traffic-profile classifier name <WORD>

show qos traffic-profile classifier name <WORD> eval-order <1-255>

show qos traffic-profile interface

show qos traffic-profile set

show qos traffic-profile set name <WORD>

show qos traffic-profile set port <port> name <WORD>

show qos traffic-profile statistics port <port> name <WORD>

show qos traffic-profile statistics port <port> name <WORD> precedence <1-9>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionclassifier Display QoS traffic profile classifier entries.eval-order <1-255>

Specify the evaluation order to reference a specific traffic profile classifierentry.

interface Display QoS traffic profile interface entries.name <WORD> Specify the label to display a specific traffic profile classifier entry.port <port> Specifies a port or list of ports.precedence <1-9> Specify the precedence used to reference the traffic profile entry.set Display QoS traffic profile set entries.statistics Display QoS traffic profile statistics.



Avaya.com/support


Command: show quickconfig


show quickconfig

Displays quick config status.

Syntax

show quickconfig

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show radius


show radius

Displays the RADIUS configuration.

Syntax

show radius reachability

show radius use-management-ip

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionreachability Shows RADIUS reachability settings.use-management-ip Display RADIUS use-management-ip setting.



Avaya.com/support


Command: show radius-server


show radius-server

Displays current RADIUS server, port, and key configuration.

Syntax

show radius-server

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show rate-limit


show rate-limit

Displays rate-limiting settings and statistics.

Syntax

show rate-limit

show rate-limit port <port>

Default

None

Command mode

Privileged EXEC

Command parameters




Avaya.com/support


Command: show rear-port


show rear-port

Displays the rear-port mode configuration.

Syntax

show rear-port mode

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show rmon alarm


show rmon alarm

Displays RMON alarm entries.

Syntax

show rmon alarm

show rmon alarm sort-reverse

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionsort-reverse Display RMON alarm entries in the reverse order.



Avaya.com/support


Command: show rmon ethernet


show rmon ethernet

Displays RMON Ethernet statistics table entries.

Syntax

show rmon ethernet history

show rmon ethernet history delta

show rmon ethernet history interval-range <hh:mm:ss> <hh:mm:ss> [delta] [port <port>]

show rmon ethernet history port <port>

show rmon ethernet history sample-range <1-2147483647> <1-2147483647> [delta] [port <port>]

[interval-range <hh:mm:ss> <hh:mm:ss>]

show rmon ethernet history sample-set <1-65535> [delta] [port <port>] [interval-range

<hh:mm:ss> <hh:mm:ss>] [sample-range <1-2147483647> <1-2147483647> ]

show rmon ethernet packets

show rmon ethernet packets port <port>

show rmon ethernet statistics

show rmon ethernet statistics port <port>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<hh:mm:ss> Specify the first or second history interval-range value.<1-2147483647> Specify the first or second history sample index value.delta Display deltas of consecutive history data.interval-range Display history data for specific interval range.port <port> Specifies a port or list of ports.sample-range Display history data for specific sample range.sample-set <1-65535> Display history data for specific index.



Avaya.com/support


Command: show rmon event


show rmon event

Displays RMON event entries.

Syntax

show rmon event

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show rmon history


show rmon history

Displays RMON history entries.

Syntax

show rmon history

show rmon history port <port>

Default

None

Command mode

Privileged EXEC

Command parameters




Avaya.com/support


Command: show rmon stats


show rmon stats

Displays RMON statistics entries.

Syntax

show rmon stats

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show role


show role

Displays role settings for CLI command groups.

Syntax

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show route-map


show route-map

Displays current information about the IP route policy.

Syntax

show route-map

show route-map <WORD>

show route-map <WORD> <1-65535>

show route-map <WORD> <1-65535> detail

show route-map <WORD> detail

show route-map detail

Default

None

Command mode

User EXEC

Command parameters

Parameter Description<1-65535> Specifies a specific policy in the route policy group.<WORD> Specifies the name of a group of policies.detail Specifies the long format information of the route map.



Avaya.com/support


Command: show script


show script

Displays ASCII configuration script table entries.

Syntax

show script

show script <1-127>

show script status

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<1-127> Specifies the index of the ASCII configuration script table entry.status Displays the script status.



Avaya.com/support


Command: show serial-console


show serial-console

Displays current serial console port access.

Syntax

show serial-console

show serial-console unit <1-8>

Default

None

Command mode

Privileged EXEC

Command parameters




Avaya.com/support


Command: show serial-security


show serial-security

Displays current serial security settings.

Syntax

show serial-security

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show sflow


show sflow

Displays current settings of the SFLOW protocol.

Syntax

show sflow

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show sflow collector


show sflow collector

Displays SFLOW configuration for specified collectors.

Syntax

show sflow collector <LINE>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<LINE> Specifies the collector ID.



Avaya.com/support


Command: show sflow interface


show sflow interface

Displays SFLOW configuration for specified interfaces.

Syntax

show sflow interface <LINE>

show sflow interface enabled

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<LINE> Specifies the port number.enabled Displays sflow interfaces with non-default settings.



Avaya.com/support


Command: show sftp-server


show sftp-server

Displays the SFTP server IP address.

Syntax

show sftp-server

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show slpp


show slpp

Displays SLPP information.

Syntax

show slpp

show slpp interface

show slpp interface <WORD>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<WORD> Specifies a port or list of ports.interface Shows SLPP information per interface.



Avaya.com/support


Command: show slpp-guard


show slpp-guard

Displays SLPP-guard information.

Syntax

show slpp-guard

show slpp-guard <port>

Default

None

Command mode

User EXEC

Command parameters


port Specifies the port in one of the following formats: a single port (3), a range of ports (3-4), or a series of ports (3,5,6).



Avaya.com/support


Command: show smlt


show smlt

Displays all ports for a single port SMLT.

Syntax

show smlt

show smlt Ethernet

show smlt Ethernet <1-512>

show smlt mlt

show smlt mlt <1-64>

Default

None

Command mode

User EXEC

Command parameters

Parameter DescriptionEthernet <1-512> Displays the configuration for an SLT.mlt <1-64> Displays the configuration for a specific MLT.



Avaya.com/support


Command: show snmp-server


show snmp-server

Displays the SNMP configuration.

Syntax

show snmp-server

show snmp-server host

show snmp-server notification-control

show snmp-server notification-control <WORD>

show snmp-server notify-filter

show snmp-server user

show snmp-server view

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<WORD> Specify the description or OID of a notification type.host Display SNMP trap destinations.notification-control <WORD> Display notification control table.notify-filter Display SNMP notify filter configuration.user Display SNMP users.view Display SNMP views.



Avaya.com/support


Command: show sntp


show sntp

Displays the Simple Network Time Protocol (SNTP) configuration.

Syntax

show sntp

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show spanning-tree


show spanning-tree

Displays Spanning Tree information.

Syntax

show spanning-tree

show spanning-tree 802dot1d-port-compliance

show spanning-tree mode

Default

None

Command mode

User EXEC

Command parameters

Parameter Description802dot1d-port-compliance Displays 802dot1d port compliance mode.mode Display Spanning Tree operation mode



Avaya.com/support


Command: show spbm


show spbm

Displays global SPBM status.

Syntax

show spbm

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show ssh


show ssh

Displays SSH information. This command appears only if the switch runs a secure image.

Syntax

show ssh download-auth-key

show ssh global

show ssh session

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptiondownload-auth-key Displays authorization key and TFTP server IP address.global Displays the SSH configuration for the switch.session Displays SSH session information.



Avaya.com/support


Command: show sshc


show sshc

Shows SSH client status.

Syntax

show sshc

show sshc known-hosts

show sshc sessions

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionknown-hosts Shows SSH client known hosts.sessions Shows SSH client active sessions.



Avaya.com/support


Command: show ssl


show ssl

Displays SSL information for the switch. This command appears only if the switch runs a secure image.

Syntax

show ssl [certificate]

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptioncertificate Displays the SSL certificate stored in NVRAM and used by the SSL server.



Avaya.com/support


Command: show stack auto-unit-replacement


show stack auto-unit-replacement

Displays auto unit replacement configuration.

Syntax

show stack auto-unit-replacement

show stack auto-unit-replacement mac-addresses

Default

None

Command mode

User EXEC

Command parameters

Parameter Descriptionmac-addresses Displays the AUR MAC address cache.



Avaya.com/support


Command: show stack auto-unit-replacement-image


show stack auto-unit-replacement-image

Displays auto unit image replacement configuration.

Syntax

show stack auto-unit-replacement-image

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show stack-cable-info


show stack-cable-info

Displays cable information for the stack.

Syntax

show stack-cable-info

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show stack forced-mode


show stack forced-mode

Displays the forced stack mode.

Syntax

show stack forced-mode

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show stack health


show stack health

Display the status of each stacking link.

Syntax

show stack health

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show stack-info


show stack-info

Displays stack information.

Syntax

show stack-info

show stack-info uptime

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionuptime Shows the time each unit has been in the up state.



Avaya.com/support


Command: show stack-monitor


show stack-monitor

Displays the stack monitor configuration.

Syntax

show stack-monitor

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show stack reboot-on-failure


show stack reboot-on-failure

Displays stack reboot-on-failure status.

Syntax

show stack reboot-on-failure

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show stack retry-count


show stack retry-count

Displays stack retry count.

Syntax

show stack retry-count

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show storm-control


show storm-control

Displays packet storm control settings.

Syntax

show storm-control unicast

show storm-control unicast interface

show storm-control unicast interface <port>

show storm-control unicast interface Ethernet

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptioninterface <port> Specifies a port or list of ports.interface Ethernet Shows information per Ethernet interface.



Avaya.com/support


Command: show sys-info


show sys-info

Displays system information.

Syntax

show sys-info

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show system


show system

Displays consolidated system information.

Syntax

show system

show system last-exception [unit <1-8 | all>]

show system verbose

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionlast-exception Display last software exception information.unit <1-8 | all> Display last exception for a specified unit.verbose Display verbose system information.



Avaya.com/support


Command: show tacacs


show tacacs

Displays the status of the TACACS+ configuration.

Syntax

show tacacs

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show tech


show tech

Display technical information about the status of the system and complete information about the hardware components, softwarecomponents, and operation of the system.

Syntax

show tech

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show telnet-access


show telnet-access

Displays Telnet access configuration.

Syntax

show telnet-access

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show telnet sessions


show telnet sessions

Displays the active Telnet sessions.

Syntax

show telnet sessions

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show terminal


show terminal

Displays terminal configuration parameters.

Syntax

show terminal

Default

None

Command mode

User EXEC



Avaya.com/support


Command: show tftp-server


show tftp-server

Displays the TFTP server address.

Syntax

show tftp-server

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show trace


show trace

Displays trace information.

Syntax

show trace level

show trace modid-list

show trace status

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionlevel Show the current trace level for all modules.modid-list Show the relationship between level number and module ID to use with the trace tool.status Show the trace status.



Avaya.com/support


Command: show usb-files


show usb-files

Displays USB files.

Syntax

show usb-files

show usb-files ascii <WORD> [unit <1-8>]

show usb-files binary <WORD> [unit <1-8>]

show usb-files dir <WORD> [tree] [unit <1-8>]

show usb-files tree [dir <WORD>] [unit <1-8>]

show usb-files unit <1-8> dir <WORD> [tree]

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<WORD> Specifies te filename which will be displayed.ascii Displays the ASCII contents of a file.binary Displays the binary contents of a file.dir Shows files from a specific directory.tree Lists subdirectories recursively.unit <1-8> Specifies a unit number in a stack.



Avaya.com/support


Command: show usb-host-port


show usb-host-port

Displays USB host port information.

Syntax

show usb-host-port

show usb-host-port all

show usb-host-port unit <1-8>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptionall Display USB host port information for all units.unit <1-8> Display USB host port information of an unit in stack.



Avaya.com/support


Command: show username


show username

Displays username settings.

Syntax

show username <LINE>

Default

None

Command mode

User EXEC

Command parameters

Parameter DescriptionLINE Display usernmae settings.



Avaya.com/support


Command: show vlacp


show vlacp

Displays the VLACP configuration.

Syntax

show vlacp

show vlacp interface [<port>]

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<port> Specifies a port or list of ports.interface Displays VLACP configuration for specified interfaces.



Avaya.com/support


i-sid C-VLAN to I-SIDassociations.

<1-4094>Specifies aVLAN or listof VLANs.

<vlan>Specifies aVLAN or listof VLANs.

configcontrolDisplaysVLAN controlmode.

dhcp-relay

DisplaysDHCP relayinfo for aparticularVLAN.

idDisplays aspecificVLAN.

mgmtDisplays themanagementVLAN ID.

multicast membersip <1-4094>

DisplaysVLANmulticastconfiguration.

remote-spanDisplaysRSPANVLANs.

summaryDisplays asummary ofVLANs.

type <port | protocol-decEther2 | protocol-decOtherEther2 |Protocol-ipEther2 | protocol-ipv6Ether2 | protocol-ipx802.2 |protocol-ipx802.3 | protocol-ipxEther2 | protocol-ipxSnap |protocol-Netbios | protocol-RarpEther2 | protocol-sna802.2 |protocol-snaEther2 | protocol-Userdef | protocol-vinesEther2 |protocol-xnsEther2 | spbm-bvlan | spbm-switchedUni>

Displays aspecific typeof VLAN.



Avaya.com/support


Command: show vlan configcontrol


show vlan configcontrol

Displays VLAN control mode.

Syntax

Default

None

Command mode




Avaya.com/support


Command: show vlan dhcp-relay


show vlan dhcp-relay

Displays DHCP relay info for a particular VLAN.

Syntax

Default

None

Command mode




Avaya.com/support


Command: show vlan id


show vlan id

Displays specific VLAN.

Syntax

Default

None

Command mode




Avaya.com/support


Command: show vlan igmp


show vlan igmp

Displays IGMP snoop settings.

Syntax

Default

None

Command mode




Avaya.com/support


Command: show vlan interface


show vlan interface

Displays VLAN configuration for specified interfaces.

Syntax

Default

None

Command mode




Avaya.com/support


Command: show vlan ip


show vlan ip

Displays IP info for VLANs.

Syntax

Default

None

Command mode




Avaya.com/support


Command: show vlan i-sid


show vlan i-sid

Displays the C-VLAN to I-SID associations.

Syntax

Default

None

Command mode




Avaya.com/support


Command: show vlan mgmt


show vlan mgmt

Displays mgmt vlan ID.

Syntax

Default

None

Command mode




Avaya.com/support


Command: show vlan multicast


show vlan multicast

Displays VLAN multicast configuration.

Syntax

Default

None

Command mode




Avaya.com/support


Command: show vlan remote-span


show vlan remote-span

Displays Rspan VLANs.

Syntax

Default

None

Command mode




Avaya.com/support


Command: show vlan summary


show vlan summary

Displays a summary of VLANs.

Syntax

Default

None

Command mode




Avaya.com/support


Command: show vlan type


show vlan type

Displays specific type of VLAN.

Syntax

Default

None

Command mode




Avaya.com/support


Command: show vlan voice-vlan


show vlan voice-vlan

Displays voice VLANs.

Syntax

Default

None

Command mode




Avaya.com/support


Command: show web-server


show web-server

Displays the status of the web server.

Syntax

show web-server

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: show who


show who

Displays the users authenicated by AAA.

Syntax

show who

Default

None

Command mode

User EXEC



Avaya.com/support


Command: shutdown (EthernetInterface Configuration)


shutdown (Ethernet Interface Configuration)

Shuts down the selected interface.

Syntax

default shutdown [port <port>]

no shutdown [port <port>]

shutdown port <port>

Default

None

Command mode


Command parameters

Parameter Descriptionport <portlist> Specify the port or list of ports to shutdown.



Avaya.com/support


Command: shutdown (Privileged EXEC)


shutdown (Privileged EXEC)

Saves the configuration and shuts down the stack or switch.

Syntax

shutdown

shutdown cancel

shutdown force [minutes-to-wait <1-60>]

shutdown minutes-to-wait <1-60>

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Descriptioncancel Cancels a previously scheduled shutdown.force Does not ask for confirmation.minutes-to-wait <1-60> Specifies the minutes to wait before the reset.



Avaya.com/support


Command: slamon agent-comm-port


slamon agent-comm-port

Configures the agent-to-agent communication port.

Syntax

default slamon agent-comm-port

slamon agent-comm-port {0 |<1024-65535>}

Default

50012

Command mode


Command parameters

Parameter Description{0 |<1024-65535>}

Configures the SLA Monitor agent-to-agent communication UDP port. The defaultport is 50012.



Avaya.com/support


Command: slamon agent ip address


slamon agent ip address

Configures the agent IP address.

Syntax

default slamon agent ip address

slamon agent ip address {A.B.C.D}

Default

None

Command mode


Command parameters


{A.B.C.D} Configures the agent IP address. If no IP address is specified, the default value is0.0.0.0, which causes the agent to use the switch/stack IP address.



Avaya.com/support


Command: slamon agent port


slamon agent port

Configures the UDP port.

Syntax

default slamon agent port

slamon agent port {0 |<1024-65535>}

Default

50011

Command mode


Command parameters

Parameter Description{0|<1024-65535>}

Configures the UDP port for agent-server communication. The agent receives discoverypackets on this port. The default is port 50011. The server must use the same port.



Avaya.com/support


Command: slamon cli


slamon cli

Enables the SLA Mon™ agent CLI support.

Syntax

default slamon cli

no slamon cli

no slamon cli enable

slamon cli

slamon cli enable

Default

Disabled

Command mode




Avaya.com/support


Command: slamon cli-timeout


slamon cli-timeout

Configures the agent automatic CLI session timeout value.

Syntax

default slamon cli-timeout

slamon cli-timeout <60-600>

Default

60

Command mode


Command parameters

Parameter Description<60-600> Configures the CLI timeout value in seconds. The default is 60 seconds



Avaya.com/support


Command: slamon cli-timeout-mode


slamon cli-timeout-mode

Enables the agent automatic CLI session timeout.

Syntax

no slamon cli-timeout-mode

no slamon cli-timeout-mode enable

pe

slamon cli-timeout-mode

slamon cli-timeout-mode enable

Default

Enabled

Command mode




Avaya.com/support


Command: slamon ntr


slamon ntr

Executes a new trace route (NTR) test on the network to establish the QoS benchmark.

Syntax

slamon ntr {A.B.C.D} <0-63>

slamon ntr {A.B.C.D} <0-63> attempts <1-10>

slamon ntr {A.B.C.D} <0-63> attempts <1-10> period <1000-200000>

slamon ntr {A.B.C.D} <0-63> period <1000-200000>

Default

None

Command mode


Command parameters


<0-63> Specifies the Differential Services Code Point (DSCP) value for use in packets thatare generated by the NTR test.

<A.B.C.D> Specifies the destination IP address. If no IP address is specified, the test executionfails.

attempts <1-10>

Specifies the number of attempts generated by the NTR test. The default value is 2.

period<1000-200000>

Specifies the interval between packets in microseconds, generated by the NTR test.The default interval is 20000 microseconds.



Avaya.com/support


Command: slamon oper-mode


slamon oper-mode

Enables the SLA Mon™ agent.

Syntax

default slamon oper-mode

no slamon oper-mode

no slamon oper-mode enable

slamon oper-mode

slamon oper-mode enable

Default

Disabled

Command mode




Avaya.com/support


Command: slamon refuse-server-tests


slamon refuse-server-tests

Enables the agent refuse server test mode.

Syntax

default slamon refuse-server-tests

no slamon refuse-server-tests

no slamon refuse-server-tests refuse

slamon refuse-server-tests

slamon refuse-server-tests refuse

Default

Refuse tests

Command mode


Command parameters

Parameter Descriptionrefuse Enables the mode.



Avaya.com/support


Command: slamon RTP


slamon RTP

Executes a real time protocol (RTP) test on the network to establish the QoS benchmark.

Syntax

slamon RTP {A.B.C.D} <0-63>

slamon RTP {A.B.C.D} <0-63> npack <10-100>

slamon RTP {A.B.C.D} <0-63> npack <10-100> nsync <10-100> period <1000-200000>

slamon RTP {A.B.C.D} <0-63> nsync <10-100>

slamon RTP {A.B.C.D} <0-63> period <1000-200000>

Default

None

Command mode


Command parameters

Parameter Description<0-63> Specifies the DSCP value for use in packets that are generated by the RTP test.

<A.B.C.D> Specifies the destination IP address. If no IP address is specified, the test executionfails.

npack <10-100>

Specifies the RTP npack value. The default value is 50.

nsync <10-100>

Specifies the RTP nsync value. The default value is 10.

period<1000-200000>

Specifies the interval between packets in microseconds, generated by the RTP test.The default interval is 20000 microseconds.



Avaya.com/support


Command: slamon server-bypass


slamon server-bypass

Enables the agent server bypass mode.

Syntax

default slamon server-bypass

no slamon server-bypass

no slamon server-bypass enable

slamon server-bypass

slamon server-bypass enable

Default

Enabled

Command mode




Avaya.com/support


Command: slamon server ip address


slamon server ip address

Configures the agent server IP address.

Syntax

default slamon server ip address

slamon server ip address {A.B.C.D}

slamon server ip address {A.B.C.D} {A.B.C.D}

Default

None

Command mode


Command parameters

Parameter Description{A.B.C.D}{A.B.C.D}

Restricts the agent to use of this server IP address only. The default is 0.0.0.0, whichmeans the agent can register with any server. You can optionally provide the IP addressfor a second server to act as a backup.



Avaya.com/support


Command: slamon server port


slamon server port

Configure the server TCP registration port.

Syntax

default slamon server port

slamon server port <0-65535>

Default

0

Command mode


Command parameters

Parameter Description<0-65535>

Restricts the agent to use of this registration port only. The default is 0, which means theagent disregards the source port information in server traffic. The server must use thesame port.



Avaya.com/support


Command: slpp (Ethernet InterfaceConfiguration)


slpp (Ethernet Interface Configuration)

Enable Simple Loop Prevention Protocol (SLPP) by port to detect a loop and automatically stop it.

Syntax

default slpp [enable] [packet-rx-threshold] [port <port>]

no slpp [enable] [port <port>]

slpp [port <port>] enable [packet-rx-threshold <1-500>]

slpp [port <port>] packet-rx-threshold <1-500>

Default

Disabled

Command mode


Command parameters

Parameter Descriptionenable Enables or disables SLPP packet reception on the port. The default is disabled.packet-rx-threshold<1-500>

Specifies the SLPP reception threshold on the ports, expressed as an integer. Thepacket reception threshold specifies the number of SLPP packets the port receivesbefore it is administratively disabled. The default is 5.

port<port>

Specify the port or list of ports.



Avaya.com/support


Command: slpp (Global Configuration)


slpp (Global Configuration)

Configures SLPP globally.

Syntax

default slpp [enable] [ethertype] [timeout] [tx-interval] [vid]

no slpp [enable] [timeout] [vid <WORD>]

slpp enable

slpp ethertype <0x0600-0xffff>

slpp timeout <0 | 1-65535>

slpp tx-interval <500-5000>

slpp vid <WORD>

Default

None

Command mode


Command parameters

Parameter Descriptionenable Enables SLPP globally. The default is disabled.ethertype<0x0600-0xffff>

Configures the SLPP PDU ethertype value. You cannot set the SLPP ethertype value toan ethertype value reserved for common protocols, such as LLDP, ARP, and IPv6. Thedefault is 0x8102.

timeout <0| 1-65535>

Configures the auto enable timer for ports shut down by SLPP. If the value is set to 0,ports shut down by SLPP remain disabled until manually re enabled. The default isdisabled.

tx-interval<500-5000>

Configures the SLPP PDU transmit interval. The default is 500.

vid <VLANID>

Adds a VLAN to the SLPP transmitting list.



Avaya.com/support


Command: slpp-guard (EthernetInterface Configuration)


slpp-guard (Ethernet Interface Configuration)

Configures SLPP Guard for switch ports.

Syntax

default slpp-guard [port <port>] [enable] [timeout]

no slpp-guard [port <port>] [enable] [timeout]

slpp-guard port <port> enable [timeout {0 | <10-65535>}]

Default

None

Command mode


Command parameters

Parameter Descriptionenable Enables SLPP Guard parameters for a port or list of ports.port<port>

Specifies the port or list of ports on which the specified SLPP Guard parameter orparameters are configured

timeout{0 |<10-65535>}

Specifies the time period, in seconds, for which SLPP Guard disables the port. After thetimeout period expires, the switch re-enables the port. The timeout value can be 0 or avalue ranging from 10 to 65535. With a value of 0, the port remains disabled until it ismanually re-enabled. The default timeout value is 60 seconds.



Avaya.com/support


Command: slpp-guard (GlobalConfiguration)


slpp-guard (Global Configuration)

Specifies an SLPP Guard Ethernet type for the switch.

Syntax

default slpp-guard [ethertype]

slpp-guard ethertype <0x0600-0xffff>

Default

0x8102

Command mode


Command parameters

Parameter Descriptionethertype <0x0600-0xffff>

Specifies a hexadecimal value ranging from 0x0600 to 0xffff. Use the prefix0x to type the hexadecimal



Avaya.com/support


Command: smlt (Ethernet InterfaceConfiguration)


smlt (Ethernet Interface Configuration)

Configures an SLT.

Syntax

default smlt [port <port>]

no smlt [port <port>]

smlt <1-512>

smlt port <port>

Default

None

Command mode


Command parameters

Parameter Description<1-512> Specifies a numerical ID for the SMLT.port <port> Specifies a port.



Avaya.com/support


Command: smlt (MLT InterfaceConfiguration)


smlt (MLT Interface Configuration)

Configures an SMLT from an existing MLT.

Syntax

default smlt

no smlt

smlt <1-512>

Default

None

Command mode


Command parameters

Parameter Description<1-512> Specifies a numerical ID for the SMLT.



Avaya.com/support


Command: snmp-server bootstrap


snmp-server bootstrap

Specifies how to secure SNMP communications, as described in the SNMPv3 standards.

Syntax

snmp-server bootstrap <minimum-secure | semi-secure | very-secure>

Default

None

Command mode


Command parameters

Parameter Description<minimum-secure>

Specifies a minimum security configuration that allows read access and notify access toall processes (view restricted) with noAuthnoPriv and read, write, and notify access to allprocesses (internet view) using AuthnoPriv and Auth-Priv.

<semi-secure>

Specifies a minimum security configuration that allows read access and notify access toall processes (view restricted) with noAuthnoPriv and read, write, and notify access to allprocesses (internet view) using AuthnoPriv and Auth-Priv.

<very-secure>

Specifies a maximum security configuration that allows no access to the users.



Avaya.com/support


Command: snmp-server community


snmp-server community

Creates community strings with varying levels of read, write, and notification access based on SNMPv3 views.

Syntax

default snmp-server community [ro] [rw]

no snmp-server community [<WORD>] [ro] [rw]

snmp-server community [<WORD>] [notify-view <WORD>] [read-view <WORD>] [ro] [rw] [write-

view <WORD>]

Default

None

Command mode


Command parameters

Parameter Description<WORD> Specifies the SNMP community string.notify-view<WORD>

Changes the notify view settings used by the new community string for differenttypes of SNMP operations.

read-view<WORD>

Changes the read view used by the new community string for different types ofSNMP operations.

ro Specifies read-only (ro) access for an SNMP server community.rw Specifies read-write (rw) access for an SNMP server community.write-view<WORD>

Changes the write view used by the new community string for different types ofSNMP operations.



Avaya.com/support


Command: snmp-server contact


snmp-server contact

Adds or removes a contact person name for a managed SNMP server system node.

Syntax

default snmp-server contact

no snmp-server

snmp-server contact <name>

Default

None

Command mode


Command parameters


<name> Specifies an alphanumeric character string that identifies a contact person for a managedSNMP server system node.



Avaya.com/support


Command: snmp-server disable


snmp-server disable

Disables SNMP server access to the switch.

Syntax

no snmp-server

snmp-server disable

Default

Disabled in the secure image. Enabled in the non-secure image.

Command mode




Avaya.com/support


Command: snmp-server enable


snmp-server enable

Enables SNMP server access to the switch.

Syntax

no snmp-server

snmp-server enable

Default

Disabled in the secure image. Enabled in the non-secure image.

Command mode




Avaya.com/support


Command: snmp-server host


snmp-server host

Adds SNMP trap receivers to the trap receiver table or remove trap receivers from the table.

Syntax

default snmp-server host

no snmp-server host [A.B.C.D | <WORD>] [port <1-165535>] [v1] [v2c] [v3 <WORD>] [<WORD>]

snmp-server host {A.B.C.D | <WORD>} [port <1-165535>] v1 <WORD> [filter <WORD>]

snmp-server host {A.B.C.D | <WORD>} [port <1-165535>] v2c <WORD> [filter <WORD>] [inform]

[retries <0-255>] [timeout <1-2147483647>]

snmp-server host {A.B.C.D | <WORD>} [port <1-165535>] v3 {auth | no-auth | auth-priv}

<WORD> [filter <WORD>] [inform] [retries <0-255>] [timeout <1-2147483647>]

snmp-server host {A.B.C.D | <WORD>} <WORD>

Default

None

Command mode


Command parameters

Parameter Description{A.B.C.D |<WORD>}

Specifies the address of a host for the trap destination.

<WORD> If you use the proprietary method for SNMP, this parameter specifies a communitystring that works as a password and permits access to the SNMP protocol.

filter<WORD>

Specifies a filter profile name.

inform Generates acknowledge Inform requests.port <1-165535>

Specifies a value for the SNMP trap port.

retries<0-255>

Specifies the retries for inform requests.

timeout<1-2147483647>

Specifies the timeout for inform requests (centi-seconds).

To configure the standards-based tables, using v1 creates trap receivers in the

v1 <WORD> SNMPv3 MIBs. Multiple trap receivers with varying access levels can be created.

v2c <WORD> To configure the new standards-based tables, using v2c creates trap receivers in theSNMPv3 MIBs. Multiple trap receivers with varying access levels can be created.

v3 {auth |no-auth |auth-priv}<WORD>

To configure the new standards-based tables, using v3 creates trap receivers in theSNMPv3 MIBs. Multiple trap receivers with varying access levels can be created. Authspecifies SNMPv3 traps are sent using authentication and no privacy. noauth specifiesSNMPv3 traps are sent using with no authentication and no privacy. auth-priv specifiestraps are sent using authentication and privacy; this parameter is available only if theimage has full SHA/DES support. <WORD> specifies the username



Avaya.com/support


Command: snmp-server location


snmp-server location

Configures the system location.

Syntax

default snmp-server location

no snmp-server location

snmp-server location <location>

Default

None

Command mode


Command parameters


<location> Specifies an alphanumeric value, with a maximum of 255 characters, for the SNMPsystem location.



Avaya.com/support


Command: snmp-server name


snmp-server name

Configues a system name.

Syntax

default snmp-server name

no snmp-server name

snmp-server name <name>

Default

None

Command mode


Command parameters


<name> Specifies an alphanumeric value, with a maximum of 255 characters, for the SNMPsystem name.



Avaya.com/support


Command: snmp-server notification-control


snmp-server notification-control

Enables or disables SNMP trap notifications by notification type.

Syntax

default snmp-server notification-control <WORD> [<port>]

no snmp-server notification-control <WORD> [<port>]

snmp-server notification-control <WORD> [<port>]

Default

None

Command mode


Command parameters

Parameter Description<port> Specifies a port or list of ports.<WORD> Specifies an alphanumeric description or the OID of a supported notification type.



Avaya.com/support


Command: snmp-server notify-filter


snmp-server notify-filter

Creates an SNMP notify filter.

Syntax

no snmp-server notify-filter <name> <WORD>

snmp-server notify-filter <name> <WORD> [<WORD>]

Default

None

Command mode


Command parameters

Parameter Description<name> Specifies the filter profile name.

<WORD> Specifies an alphanumeric description or the OID filter specification. You can add morethan one description or OID in the same command string.



Avaya.com/support


Command: snmp-server user


snmp-server user

Creates an SNMPv3 user.

Syntax

no snmp-server user <WORD>

no snmp-server user engine-id <WORD> <WORD>

snmp-server user <WORD> md5 <password>

snmp-server user <WORD> notify-view <WORD> [md5 <password>]

snmp-server user <WORD> read-view <WORD> [md5 <password>]

snmp-server user <WORD> write-view <WORD> [md5 <password>]

snmp-server user engine-id <WORD> <WORD> [md5 <password>]

Default

None

Command mode


Command parameters

Parameter Description<WORD> Specifies the username.engine-id <WORD> Specifies the SNMP engine ID for the remote user.md5 <password> Selects the MD5 authentication protocol and provides the MD5 password.notify-view <WORD> Specifies the notify view to which the new user has access.read-view <WORD> Specifies the read view to which the new user has access.write-view <WORD> Specifies the write view to which the new user has access.



Avaya.com/support


Command: snmp-server view


snmp-server view

Creates and SNMPv3 view.

Syntax

no snmp-server view <WORD>

snmp-server view <WORD> <OID> [<OID>]

Default

None

Command mode


Command parameters


<OID>

Specifies the Object identifier. The OID can be entered as a dotted form OID. Each OIDmust be preceded by a + or - sign (if this is omitted, a + sign is implied). For the dottedform, a sub-identifier can be an asterisk, indicating a wildcard. The + or - indicateswhether the specified OID is included in or excluded from, the set of MIB objectsaccessible using this view. You can specify 10 possible OID values in the same commandstring.

<WORD> Specifies an alphanumeric value that provides a unique name for the SNMPv3 view.



Avaya.com/support


Command: snmp trap


snmp trap

Allows or disallows a specific SNMP trap.

Syntax

default snmp trap link-status [port]

no snmp trap link-status [port]

snmp trap link-status [port] {enable | disable}

Default

Enabled

Command mode


Command parameters

Parameter Descriptionlink-status [port] {enable |disable}

Enables or disables link status SNMP trap generation for oneor more switch ports.



Avaya.com/support


Command: sntp enable


sntp enable

Enables or disables Simple Network Time Protocol (SNTP).

Syntax

default sntp enable

no sntp enable

sntp enable

Default

Disabled

Command mode




Avaya.com/support


Command: sntp server


sntp server

Configures Simple Network Time Protocol (SNTP) addresses.

Syntax

default sntp server primary

default sntp server secondary

no sntp server primary

no sntp server secondary

sntp server primary address <A.B.C.D|WORD>

sntp server secondary address <A.B.C.D|WORD>

Default

0.0.0.0

Command mode


Command parameters

Parameter Descriptionprimary address <A.B.C.D|WORD> Specifies the primary SNTP IP address, or IPv6 address.secondary address<A.B.C.D|WORD>

Specifies the secondary SNTP IP address, or IPv6address.



Avaya.com/support


Command: sntp sync-interval


sntp sync-interval

Sets the interval, in hours, for recurring SNTP syncronization.

Syntax

default sntp sync-interval

sntp sync-interval <0-168>

Default

24 hours

Command mode


Command parameters


<0-168> Specifies the recurring synchronization interval in hours. Values range from 0 to 168. Thedefault is 24.



Avaya.com/support


Command: sntp sync-now


sntp sync-now

Forces a manual SNTP syncronization.

Syntax

sntp sync-now

Default

None

Command mode




Avaya.com/support


Command: spanning-tree 802dot1d-port-compliance enable


spanning-tree 802dot1d-port-compliance enable

Enables or disables spanning tree 802dot1d port compliance.

Syntax

default spanning-tree 802dot1d-port-compliance enable

no spanning-tree 802dot1d-port-compliance enable

spanning-tree 802dot1d-port-compliance enable

Default

Disabled

Command mode




Avaya.com/support


Command: spanning-tree add-vlan


spanning-tree add-vlan

Adds a specific VLAN to a Spanning Tree Group (STG).

Syntax

spanning-tree add-vlan <1-4094>

Default

None

Command mode


Command parameters

Parameter Description<1-4094> Specifies the VLAN identifier (VID) to add to the STG. Values range from 1 to 4094.



Avaya.com/support


Command: spanning-tree bpdu-filtering(Ethernet Interface Configuration)


spanning-tree bpdu-filtering (Ethernet Interface Configuration)

Configures STP BPDU filtering.

Syntax

default spanning-tree bpdu-filtering [port <port> [enable] [timeout]

no spanning-tree bpdu-filtering [port <port>] [enable]

spanning-tree bpdu-filtering [port <port>] enable [timeout <10-65535 | 0>]

Default

None

Command mode


Command parameters

Parameter Descriptionenable Enables STP BPDU Filtering on the specified ports. The default value is disabled.port<port>

Specifies the ports affected by the command.

timeout<10-65535 |0>

When BPDU filtering is enabled, this indicates the time (in seconds) during which the portremains disabled after it receives a BPDU. The port timer is disabled if this value is set to0. The default value is 120 seconds.



Avaya.com/support


Command: spanning-tree bpdu-filteringignore-self (Global Configuration)


spanning-tree bpdu-filtering ignore-self (Global Configuration)

Enables or disables spanning tree BPDU filtering ignore self option.

Syntax

default spanning-tree bpdu-filtering ignore-self

no spanning-tree bpdu-filtering ignore-self

spanning-tree bpdu-filtering ignore-self

Default

Disabled

Command mode




Avaya.com/support


Command: spanning-tree cost-calc-mode


spanning-tree cost-calc-mode

Sets the path cost calculation mode for all Spanning Tree Groups on the VSP 7000 Series switches.

Syntax

default spanning-tree cost-calc-mode

spanning-tree cost-calc-mode {dot1d | dot1t}

Default

802.1d

Command mode


Command parameters

Parameter Description{dot1d |dot1t}

Specifies the STG path cost calculation mode. Values include dot1d and dot1t. Thedefault is dot1d.



Avaya.com/support


Command: spanning-tree (EthernetInterface Configuration)


spanning-tree (Ethernet Interface Configuration)

Sets the Spanning Tree Protocol (STP) participation for the ports within the specified Spanning Tree Group.

Syntax

default spanning-tree [port <port>] [cost] [learning] [priority] [stp <1-8>]

no spanning-tree [port <port>] [stp <1-8>]

spanning-tree [port <port>] cost <1-65535> [priority {00 | 10 | < | F0}]

spanning-tree [port <port>] learning {disable | normal | fast} [cost <1-65535>] [priority

{00 | 10 | < | F0}]

spanning-tree [port <port>] priority {00 | 10 | < | F0}

spanning-tree [port <port>] stp <1-8> [cost <1-65535>] [learning {disable | normal | fast}

] [priority {00 | 10 | < | F0}]

Default

None

Command mode


Command parameters

Parameter Descriptioncost <1-65535> Enter the path cost of the spanning tree; range is from 1–65535.

learning{disable|normal|fast}

Specify the STP learning mode: disable: disables FastLearn mode;normal: changes to normal learning mode; fast: enables FastLearnmode.

port <port>

Enable the spanning tree for the specified port or ports; enter port orports you want enabled for the spanning tree. If you omit thisparameter, the system uses the port number you specified when youissued the interface command to enter the Interface Configurationmode.

priority {00 | 10 |< | F0}

Set the spanning tree priority for a port as a hexadecimal value.

stp <1-8> Specify the spanning tree group; enter the STG ID.



Avaya.com/support


Command: spanning-tree forward-time


spanning-tree forward-time

Sets the STG forward time in seconds.

Syntax

default spanning-tree forward-time

spanning-tree forward-time <4-30>

Default

15

Command mode


Command parameters

Parameter Description<4-30> Specifies the STG forward time in seconds. Values range from 4 to 30. The default is 15.



Avaya.com/support


Command: spanning-tree hello-time


spanning-tree hello-time

Sets the STG hello time in seconds.

Syntax

default spanning-tree hello-time

spanning-tree hello-time <1-10>

Default

2

Command mode


Command parameters

Parameter Description<1-10> Specifies the STG hello time in seconds. Values range from 1 to 10. The default is 2.



Avaya.com/support


Command: spanning-tree max-age


spanning-tree max-age

Sets the STG maximum age time in seconds.

Syntax

default spanning-tree max-age

spanning-tree max-age <6-40>

Default

20

Command mode


Command parameters


<6-40> Specifies the STG maximum age time in seconds. Values range from 6 to 40. The defaultis 20.



Avaya.com/support


Command: spanning-tree mode


spanning-tree mode

Sets the spanning tree operating mode.

Syntax

spanning-tree mode {mst | rstp | stpg}

Default

None

Command mode


Command parameters

Parameter Description{mst | rstp | stpg} Specifies the STG operating mode. Values include mst, rstp, and stpg.



Avaya.com/support


Command: spanning-tree multicast-address


spanning-tree multicast-address

Sets the spanning tree multicast MAC address.

Syntax

default spanning-tree multicast-address

spanning-tree multicast-address <H.H.H.H | xx:xx:xx:xx:xx:xx | xx.xx.xx.xx.xx.xx | xx-xx-

xx-xx-xx-xx>

Default

01-80-C2-00-00-00

Command mode


Command parameters

Parameter Description<H.H.H.H | xx:xx:xx:xx:xx:xx |xx.xx.xx.xx.xx.xx | xx-xx-xx-xx-xx-xx>

Specifies the spanning tree multicast addressin either of the listed formats.



Avaya.com/support


Command: spanning-tree port-mode


spanning-tree port-mode

Sets the STG port membership for all Spanning Tree Groups on the VSP 7000 Series switches.

Syntax

default spanning-tree port-mode

spanning-tree port-mode {auto | normal}

Default

auto

Command mode


Command parameters

Parameter Description{auto |normal}

Specifies the STG port membership mode. Values include auto and normal. Thedefault is auto.



Avaya.com/support


Command: spanning-tree priority


spanning-tree priority

Sets the spanning tree priority in hexadecimal. If 802.1T compliant, this value must be a multiple of 0x1000.

Syntax

default spanning-tree priority

spanning-tree priority {0000 | 1000 | 2000 | 3000 | .... | e000 | f000}

Default

8000 (Hex)

Command mode


Command parameters

Parameter Description{0000 | 1000 | 2000 | 3000 |.... | e000 | f000}

Specifies the spanning tree priority. Values range from 0000to f000 hexadecimal. The default is 8000.



Avaya.com/support


Command: spanning-tree remove-vlan


spanning-tree remove-vlan

Removes a specific VLAN from a Spanning Tree Group (STG).

Syntax

spanning-tree remove-vlan <1-4094>

Default

None

Command mode


Command parameters

Parameter Description<1-4094> Specifies the VLAN identifier (VID) to remove from the STG. Values range from 1 to 4094.



Avaya.com/support


Command: spanning-tree stp


spanning-tree stp

Selects a Spanning Tree Group (STG) to configure.

Syntax

default spanning-tree stp <1-8>

spanning-tree stp <1-8>

Default

None

Command mode


Command parameters

Parameter Description<1-8> Specifies a Spanning Tree Group (STG) identifer.



Avaya.com/support


Command: spanning-tree tagged-bpdu


spanning-tree tagged-bpdu

Sets the BPDU on the tagged port as tagged or untagged.

Syntax

default spanning-tree tagged-bpdu

spanning-tree tagged-bpdu {disable | enable}

Default

Disabled

Command mode


Command parameters

Parameter Description{disable | enable} Enables or disables BPDU tagging on tagged ports.



Avaya.com/support


Command: spanning-tree tagged-bpdu-vid


spanning-tree tagged-bpdu-vid

Sets the VLAN identifier (VID) for the tagged BPDU.

Syntax

spanning-tree tagged-bpdu-vid <1-4094>

Default

4001–4008 for STG 1–8 respectively

Command mode


Command parameters

Parameter Description<1-4094> Specifies the VLAN identifier (VID) for the tagged BPDU. Values range from 1 to 4094.



Avaya.com/support


Command: spbm


spbm

Enables or disables Shortest Path Bridging MAC (SPBM) globally.

Syntax

default spbm

no spbm

spbm

Default

Disabled

Command mode




Avaya.com/support


Command: spbm ethertype


spbm ethertype

Configures the SPBM ethertype.

Syntax

default spbm ethertype

spbm ethertype {0x8100 | 0x88a8}

Default

0x8100

Command mode


Command parameters

Parameter Description{0x8100 |0x88a8}

Sets the SPBM ethertype. Values include 0x8100 and 0x88a8. The default is0x8100.



Avaya.com/support


Command: spbm (ISIS RouterConfiguration)


spbm (ISIS Router Configuration)

Creates the SPBM instance.

Syntax

default spbm <1-100>

no spbm <1-100>

no spbm <1-100> b-vid {<vlan-id> [-<vlan-id>][,...]}

spbm <1-100>

spbm <1-100> b-vid {<vlan-id> [-<vlan-id>][,...]} [primary <1-4094>]

Default

None

Command mode


Command parameters

Parameter Description<1-100> Creates the SPBM instance. In this release, only one SPBM instance is supportedb-vid{<vlan-id>[-<vlan-id>][,...]}

Sets the ISIS SPBM instance data VLANs. Use the no option to remove the specifiedBVLAN from the SPBM instance.

lsdb-trapenable

Enables a trap when the SPBM LSDB changes.

nick-name<x.xx.xx>

Specifies a nickname for the SPBM instance globally. The value is 2.5 bytes in theformat <x.xx.xx>. Use the no or default options to delete the configured nickname.

smlt-peer-system-id

Specifies the IS-IS SPBM peer system ID. The ID is part of the required configuration.You must configure the SMLT peer system ID as the nodal MAC of the peer device. Inthe IS-IS network, the nodal MAC of devices should be eight apart from each other.

smlt-virtual-bmac

Specifies a virtual MAC address used by both peers. SMLT virtual B-MAC is anoptional configuration.



Command: spbm lsdb-trap enable


spbm lsdb-trap enable

Enables a trap when the SPBM LSDB changes.

Syntax

default spbm <1-100> lsdb-trap enable

no spbm <1-100> lsdb-trap enable

spbm <1-100> lsdb-trap enable

Default

None

Command mode




Avaya.com/support


Command: spbm nick-name


spbm nick-name

Configures the system nickname.

Syntax

default spbm <1-100> nick-name

no spbm <1-100> nick-name

spbm <1-100> nick-name <x.xx.xx>

Default

None

Command mode


Command parameters

Parameter Descriptionnick-name<x.xx.xx>

Specifies a nickname for the SPBM instance globally. The value is 2.5 bytes in theformat <x.xx.xx>. Use the no or default options to delete the configured nickname



Avaya.com/support


Command: speed (Ethernet InterfaceConfiguration)


speed (Ethernet Interface Configuration)

Sets the port speed.

Syntax

default speed [port <port>]

speed [port <port>] {100 | 1000 | 10000 | 40000 |auto}

Default

None

Command mode


Command parameters

Parameter Description{100 | 1000 | 10000 |40000 |auto}

Set the speed to: 100: 100 Mbps; 1000: 1 Gbps; 10000: 10 Gbps;40000: 40 Gbps; auto: autonegotiation.

port <port> Specify the port or list of ports.



Avaya.com/support


Command: speed (Mgmt InterfaceConfiguration)


speed (Mgmt Interface Configuration)

Sets the port speed of the management port

Syntax

speed {10 | 100 | 1000 | auto}

Default

None

Command mode


Command parameters


10|100|1000|auto Set the speed to: 10: 10 Mbps; 100: 100 Mbps; 1000: 1000 Mbps or 1 Gbps;auto: autonegotiation.



Avaya.com/support


Command: spf-delay


spf-delay

Configures the SPF delay in milliseconds.

Syntax

default spf-delay

no spf-delay

spf-delay <0-5000>

Default

100

Command mode


Command parameters


<0-5000>

Configures the delay, in milliseconds, to pace successive Shortest Path First (SPF) runs.The timer prevents more than two SPF runs from being scheduled back-to-back. Themechanism for pacing SPF allows two back-to-back SPF runs. The default value is 100milliseconds. Use the no or default options to set this parameter to the default value of100 milliseconds.



Avaya.com/support


Command: sshc


sshc

Configures SSH client settings. This commands appears only if the switch runs a secure image.

Syntax

default sshc authentication

default sshc dsa-key

default sshc dsa-keysize

default sshc port

default sshc rsa-key

default sshc rsa-keysize

no sshc authentication

no sshc dsa-host-key

no sshc rsa-host-key

sshc authentication {dsa | password | rsa}

sshc close-session <0-8>

sshc dsa-host-key [force]

sshc dsa-key <512-1024>

sshc port <1-65535>

sshc rsa-host-key [force]

sshc rsa-key <1024-2048>

sshc upload-host-key address <A.B.C.D | WORD> [key-name <WORD>] [dsa | rsa]

sshc upload-host-key usb [unit <1-8>] key-name <WORD> [dsa | rsa]

Default

None

Command mode


Command parameters

Parameter Descriptionaddress <A.B.C.D | WORD> Uploads the authentication key from a TFTP server.authentication {dsa |password | rsa}

Enables the authentication method. The default is DSA.

close-session <0-8> Closes a client session by ID.dsa Uploads the SSH DSA authentication key.

dsa-host-key [force] Generates a new SSH DSA host key. Use the force parameter togenerate the host key without a reset.

dsa-key <512-1024> Specifies the host key size. A new key is generated as the nextsystem reboot. The default is 512.

key-name <WORD> Specifies the key filename.port <1-65535> Specifies the port to accept new connections. The default is 22.rsa Uploads the SSH RSA authentication key.

rsa-host-key [force] Generates a new SSH RSA host key. Use the force parameter togenerate the host key without a reset.

rsa-key <1024-2048> Specifies the host key size. A new key is generated as the nextsystem reboot. The default is 1024.

unit <1-8> Specifies a unit number in a stack.upload-host-key Uploads the host key.usb Uploads the authentication key to USB.



Avaya.com/support


Command: ssh (Global Configuration)


ssh (Global Configuration)

Modify Secure Shell (SSH) configuration parameters. This command appears only if the switch runs a secure image.

Syntax

default ssh dsa-auth

default ssh pass-auth

default ssh port

default ssh rsa-auth

default ssh timeout

no ssh [dsa-auth] [dsa-auth-key] [dsa-host-key] [pass-auth] [rsa-auth] [rsa-auth-key]

[rsa-host-key]

ssh

ssh download-auth-key address <A.B.C.D | WORD> [key-name <WORD>] [dsa | rsa]

ssh download-auth-key usb [unit <1-8>] key-name <WORD> [dsa | rsa]

ssh dsa-auth

ssh dsa-host-key

ssh pass-auth

ssh port <1-65535>

ssh rsa-auth

ssh rsa-host-key

ssh secure [force]

ssh timeout <1-120>

Default

Disabled

Command mode


Command parameters


address <A.B.C.D |WORD>

Downloads the authentication key from a TFTP server.

dsa Downloads the SSH DSA authentication key.dsa-auth Enables SSH DSA authentication. The default is enabled.dsa-auth-key Deletes the authentication key.dsa-host-key Generates a new SSH DSA host key.key-name <WORD> Specifies the key filename.pass-auth Enables SSH password authentication. The default is enabled.port <1-65535> Specifies the SSH port to accept new connections. The default is 22.rsa Downloads the SSH RSA authentication key.rsa-auth Enables SSH RSA authentication. The default is enabled.rsa-auth-key Deletes the authentication key.rsa-host-key Generates a new SSH RSA host key.

secure [force] Enables SSH secure mode. Use the force parameter to skipconfirmation.

timeout <1-120> Configures the SSH timeout, in seconds. The default is 60.unit <1-8> Specifies a unit number in a stack.usb Downloads the authentication key from USB.



Avaya.com/support


Command: ssh (User ExecConfiguration)


ssh (User Exec Configuration)

Connect to a remote Secure Shell (SSH) host.

Syntax

ssh <A.B.C.D|WORD>

ssh <A.B.C.D|WORD> port <0-65535>

ssh <A.B.C.D|WORD> username <WORD>

ssh <A.B.C.D|WORD> username <WORD> port <0-65535>

Default

None

Command mode

User EXEC

Command parameters

Parameter Description<A.B.C.D|WORD> Specifies the hostname, IPv4 address, or IPv6 address of the remote SSH server.

port <0-65535> Specifies the remote SSH server port number to which to connect. The default is22.

username<WORD>

Specifies the login name of the remote SSH server.



Avaya.com/support


Command: ssl


ssl

Configures Secure Socket Layer (SSL) for the switch. This command appears only if the switch runs a secure image.

Syntax

no ssl [certificate]

ssl

ssl certificate

ssl reset

Default

Active

Command mode


Command parameters

Parameter Descriptioncertificate Creates a new SSL certificate.reset Resets the SSL server.



Avaya.com/support


Command: stack auto-unit-replacementconfig


stack auto-unit-replacement config

Modifies AUR operational settings.

Syntax

stack auto-unit-replacement config restore unit <1-8>

stack auto-unit-replacement config save {disable | enable }

stack auto-unit-replacement config save unit <1-8>

Default

None

Command mode

Privileged EXEC

Command parameters


restore unit <1-8> Restore configuration of a unit from the saved configuration on thebase unit.

save {disable | enable}

Enables or disables auto-save of unit configuration to the base unit.

unit <1-8> Forces immediate save of a non base unit configuration to the baseunit.



Avaya.com/support


Command: stack auto-unit-replacementenable


stack auto-unit-replacement enable

Enables or disables Auto Unit Replacement (AUR) for switch units that are part of a stack.

Syntax

default stack auto-unit replacement enable

no stack auto-unit replacement enable

stack auto-unit replacement enable

Default

Enabled

Command mode




Avaya.com/support


Command: stack auto-unit-replacement-image enable


stack auto-unit-replacement-image enable

Enables or disables Agent Auto Unit Replacement (AAUR) for switch units that are part of a stack.

Syntax

default stack auto-unit-replacement-image enable

no stack auto-unit-replacement-image enable

stack auto-unit-replacement-image enable

Default

Enabled

Command mode




Avaya.com/support


Command: stack auto-unit-replacementremove-mac-address


stack auto-unit-replacement remove-mac-address

Removes the MAC address for a unit from the AUR cache.

Syntax

stack auto-unit-replacement remove-mac-address unit <1-8>

Default

None

Command mode

Privileged EXEC

Command parameters




Avaya.com/support


Command: stack forced-mode


stack forced-mode

Enables or disables Stack Forced Mode for switch units that are part of a stack.

Syntax

default stack forced-mode

no stack forced-mode

stack forced-mode

Default

Disabled

Command mode




Avaya.com/support


Command: stack-monitor


stack-monitor

Configures the monitoring of stack switch units to detect problems within the stack.

Syntax

default stack-monitor [enable] [stack-size] [trap-interval]

no stack-monitor enable

stack-monitor enable [stack-size <2-8>] [trap-interval <30-300>]

Default

None

Command mode


Command parameters


stack-size <2-8> Sets the stack size to be monitored. Values range from 2 to 8. Thedefault is 2

trap-interval <30-300>

Sets the trap interval value. The default is 60.



Avaya.com/support


Command: stack reboot-on-failure


stack reboot-on-failure

Enables or disables rebooting of stack units when stack communication fails.

Syntax

default stack reboot-on-failure

no stack reboot-on-failure

stack reboot-on-failure

Default

Enabled

Command mode




Avaya.com/support


Command: stack replace


stack replace

Use stack replace to replace a specific switch unit within a stack.

Syntax

stack replace unit <1-8>

Default

None

Command mode


Command parameters

Parameter Descriptionunit <1-8> Specifies the stack switch unit to replace. Values range from 1 to 8.



Avaya.com/support


Command: stack retry-count


stack retry-count

Sets the stack recovery retry count value.

Syntax

default stack retry-count

stack retry-count <0-4294967295>

Default

0

Command mode


Command parameters

Parameter Description<0-4294967295> Specifies the retry count value.



Avaya.com/support


Command: storm-control unicast(Ethernet Interface Configuration)


storm-control unicast (Ethernet Interface Configuration)

Configure per-interface packet storm control settings.

Syntax

default storm-control unicast [port <port>] [action shutdown]

no storm-control unicast [port <port>] [action shutdown]

storm-control unicast [port <port>] [action shutdown]

Default

Disabled

Command mode


Command parameters

Parameter Descriptionaction shutdown Specifies the storm control action.port <port> Specifies the port or list of ports.



Avaya.com/support


Command: storm-control unicast(Global Configuration)


storm-control unicast (Global Configuration)

Configures a maximum rate, beyond which traffic cannot traverse the switch.

Syntax

default storm-control unicast [enable] [low-watermark] [high-watermark] [poll-interval]

[trap-send-interval ]

no storm-control unicast enable

storm-control unicast enable [low-watermark <10-99999999>] [high-watermark <11-100000000>]

[poll-interval <5-300>] [trap-send-interval <0-1000>]

Default

None

Command mode


Command parameters

Parameter Descriptionenable Enables unicast storm control. The default is disabled.high-watermark<11-100000000>

Specifies the high watermark value in packets per second. Values range from11 to 100000000. The default is 500.

low-watermark<10-99999999>

Specifies the low watermark value in packets per second. Values range from10 to 99999999. The default is 200.

poll-interval <5-300>

Specifies the time period in seconds over which the packet rate is computed.Values range from 5 to 300. The default is 30.

trap-send-interval <0-1000>

Specifies the number of polling cycles between sending of traps. Valuesrange from 0 to 1000. The default is 5.



Avaya.com/support


Command: sys-name


sys-name

Configures the name for the system.

Syntax

default sys-name

no sys-name

sys-name <WORD>

Default

None

Command mode


Command parameters


<WORD>

Specifies a name for the system. This may be used as the host name for dynamic hostname exchange in accordance with RFC 2763. By default, the system name comes fromthe host name configured at the system level. Use the no or default options to set thisparameter to the default value (host name).



Avaya.com/support


Command: system-id


system-id

Configures the IS-IS system ID for the switch.

Syntax

default system-id

no system-id

system-id <xxxx.xxxx.xxxx>

Default

None

Command mode


Command parameters


<xxxx.xxxx.xxxx> Specifies the IS-IS system ID for the switch. Use the no or default options toset this parameter to the default value (node BMAC).



Avaya.com/support


Command: tacacs accounting


tacacs accounting

Use TACACS+ accounting to track the services that users access and the amount of network resources that users consume.

Syntax

tacacs accounting disable

tacacs accounting enable

Default

Disabled

Command mode


Command parameters

Parameter Descriptiondisable Disables the accounting function for the specified application.enable Enables the accounting function for the specified application.



Avaya.com/support


Command: tacacs authorization


tacacs authorization

Enables authorization for a particular privilege level.

Syntax

tacacs authorization disable

tacacs authorization enable

tacacs authorization level <1-6>

tacacs authorization level all

tacacs authorization level none

Default

Disabled

Command mode


Command parameters

Parameter Descriptiondisable Disables command authorization.enable Enables command authorization.level <1-6> Enables command authorization for a specific privilege level.level all Enables command authorization for all privilege levels.level none Disables command authorization for all privilege levels.



Avaya.com/support


Command: tacacs server host


tacacs server host

Configures the entry for the primary TACACS+ server.

Syntax

default tacacs server

default tacacs server host

default tacacs server key

default tacacs server port

no tacacs server

no tacacs server host

no tacacs server key

no tacacs server port

tacacs server host {A.B.C.D}

tacacs server host {A.B.C.D} key

tacacs server host {A.B.C.D} port <1-65535>

Default

None

Command mode


Command parameters


key Configures the secret key to share with this TACACS+ server. If the key length is zero,that indicates no encryption is used.

port <1-65535>

Configures the TCP port on which the client establishes a connection to the server. Avalue of 0 indicates that the system specified default value is used. The default is 49.



Avaya.com/support


Command: tacacs server secondary-host


tacacs server secondary-host

Configures the entry for the secondary TACACS+ server.

Syntax

default tacacs server

default tacacs server secondary-host

default tacacs server secondary-host key

default tacacs server secondary-host port

no tacacs server

no tacacs server secondary-host

no tacacs server secondary-host key

no tacacs server secondary-host port

tacacs server secondary-host {A.B.C.D}

tacacs server secondary-host {A.B.C.D} key

tacacs server secondary-host {A.B.C.D} port <1-65535>

Default

None

Command mode


Command parameters


key Configures the secret key to share with this TACACS+ server. If the key length is zero,that indicates no encryption is used.

port <1-65535>

Configures the TCP port on which the client establishes a connection to the server. Avalue of 0 indicates that the system specified default value is used. The default is 49.



Avaya.com/support


Command: tacacs switch


tacacs switch

Changes the privilege level to determine what commands a user can access through TACACS+ server authorization. You mustconfigure separate profiles in the TACACS+ server configuration file for switch level.

Syntax

tacacs switch back

tacacs switch level

tacacs switch level <1-15>

Default

None

Command mode


Command parameters

Parameter Descriptionback Returns the privilege level to the original level.level <1-15> Selects a specific privilege level.



Avaya.com/support


Command: telnet


telnet

Use this command to access another system remotely.

Syntax

telnet <A.B.C.D|WORD>

telnet <A.B.C.D|WORD> port <0-65535>

Default

None

Command mode

User EXEC

Command parameters

Parameter Description<A.B.C.D|WORD> Specifies the hostname, IPv4 address, or IPv6 address of the remote system.port <0-65535> Specifies the port number to which to connect.



Avaya.com/support


Command: telnet-access


telnet-access

Configures Telnet access to the switch using ACLI.

Syntax

default telnet-access

no telnet-access [source-ip <1-50> | <51-100>]

telnet-access disable

telnet-access enable

telnet-access inactive-timeout <0-60>

telnet-access logging {none | access | failures | all}

telnet-access login-timeout <1-10>

telnet-access retry <1-100>

telnet-access source-ip <1-50> <A.B.C.D> | <51-100> <WORD>

Default

None

Command mode


Command parameters

Parameter Descriptiondisable Disables Telnet access to the switch.enable Enables Telnet access to the switch.inactive-timeout <0-60>

Specifies, in minutes, the duration for an inactive session to beterminated. Values range from 0 to 60. The default is 15 minutes.

logging {none |access | failures |all}

Specifies the events for which to log details. The default is all.

login-timeout <1-10> Specifies the time, in minutes, to wait for Telnet and Console loginbefore the connection closes. The default is 1 minute.

retry <1-100>Specifies the number of times the user can enter an incorrect passwordbefore closing the connection. Values range from 1 to 100. The default is3.

source-ip <1-50>

<51-100> <A.B.C.D><WORD>

Specifies the source IP address from which connections are allowed.



Avaya.com/support


Command: terminal


terminal

Configures the ACLI display.

Syntax

terminal length <0-132>

terminal speed <19200|38400|9600>

terminal width <1-132>

Default

None

Command mode

User EXEC

Command parameters


length <0-132> Configures the number of lines in the output display for the currentsession.

speed<19200|38400|9600>

Configures the transmit and receive speeds.

width <1-132> Configures the width of the output display for the current session.



Avaya.com/support


Command: tftp-server


tftp-server

Configures a TFTP server IPv4 or IPv6 address for the switch.

Syntax

default tftp-server

no tftp-server

tftp-server <A.B.C.D|Word>

Default

0.0.0.0

Command mode


Command parameters

Parameter Description<A.B.C.D|Word> Specifies an IP or IPv6 address for the TFTP server.



Avaya.com/support


Command: timers basic


timers basic

Sets the RIP global timeout, holddown timer, and update timer.

Syntax

default timers basic

default timers basic timeout

default timers basic holddown

default timers basic update

timers basic timeout <15-259200>

timers basic timeout <15-259200> update

timers basic holddown <0-360>

timers basic holddown <0-360> update

timers basic update <1-360>

Default

None

Command mode


Command parameters

Parameter Descriptionholddown<0-360>

Specifies a holddown timer.

holddown<holdown-timer>

Specifies the global holddown timer, which is the length of time (in seconds) that RIPmaintains a route in the garbage list after determining that it is unreachable. During thisperiod, RIP continues to advertise the garbage route with a metric of infinity (16). If avalid update for a garbage route is received within the holddown period, the router addsthe route back into its routing table. If no update is received, the router deletes thegarbage list entry. Range is 0–360 seconds. Default is 120 seconds.

timeout<15-259200>

Specifies a global timeout.

timeout<global-

Specifies the global timeout interval parameter. If a RIP router does not receive anupdate from another RIP router within the configured timeout period, it moves theroutes advertised by the nonupdating router to the garbage list. The timeout interval

timeout> must be greater than the update timer. Range is 15–259200 seconds. Default is 180seconds.

update<1-360>

Specifies a value for the RIP update timer, which is the time interval (in seconds)between regular RIP updates. The update timer value must be less than the timeoutinterval. Default is 30 seconds.



Avaya.com/support


Command: timers basic holddown


timers basic holddown

Configures the OSPF hold own timer.

Syntax

default timers basic

default timers basic holddown

timers basic holddown <3-60>

Default

None

Command mode


Command parameters

Parameter Description<3-60> Specifies a hold down timer value between 3 and 60 seconds.



Avaya.com/support


Command: toggle-next-boot-image


toggle-next-boot-image

Toggles the next boot image. The Next Boot image in Dual Agent is an agent image that is stored in the flash memory to be usedfor the next boot. In Dual Agent, there are two agent images in the flash memory, but only one image is assigned as the NextBoot image at a time. You must restart the switch or stack after this command to use the next boot image as the new primaryimage.

Syntax

toggle-next-boot-image

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Command: trace


trace

Perform trace operations.

Syntax

trace level <1-5> <0-4>

trace screen <disable | enable>

trace shutdown

Default

None

Command mode

Privileged EXEC

Command parameters

Parameter Description<0-4> Specifies the trace level ID.<1-5> Specifies the trace module ID.screen <disable | enable> Enables or disables viewing the trace on screen.shutdown Turns off the trace.



Avaya.com/support


Command: traceroute


traceroute

Use traceroute to determine the route packets take through a network to a destination.

Syntax

traceroute <A.B.C.D|WORD>

traceroute <A.B.C.D|WORD> <1-1460>

traceroute <A.B.C.D|WORD> -m <1-255>

traceroute <A.B.C.D|WORD> -p <0-65535>

traceroute <A.B.C.D|WORD> -q <1-255>

traceroute <A.B.C.D|WORD> -v

traceroute <A.B.C.D|WORD> -w <1-255>

Default

None

Command mode

User EXEC

Command parameters

Parameter Description<1-1460> Specifies the size of the probe packet.<A.B.C.D|WORD> Specifies the hostname, IP address, or IPv6 address.-m <1-255> Specifies the is maximum time-to-live (TTL).-p <0-65535> Specifies the base UDP port number.-q <1-255> Specifies the number of probes per TTL.-v Specifies verbose mode (detailed output).-w <1-255> Specifies the wait time per probe.



Avaya.com/support


Command: usb-host-port


usb-host-port

Configures user access to USB ports on a switch or stack.

Syntax

default usb-host-port enable [unit <1-8>] enable

usb-host-port [unit <1-8>] enable

usb-host-port [unit <1-8>] enable

Default

None

Command mode


Command parameters

Parameter Descriptionenable Enables user access to the USB port on a standalone switch.unit <1-8> Specifies the USB port on a switch unit in a stack.



Avaya.com/support


Command: username


username

Configures user credentials.

Syntax

default username <LINE> [enable|ssh-access|telnet-access]

no username <LINE> [enable|ssh-access|telnet-access]

username {add | lockout-time | password | WORD}

Default

None

Command mode




Avaya.com/support


Command: username add


username add

Configures local read-write (RW) and read-only (RO) users accounts

Syntax

username add <WORD> role-name {RO|RW} password

Default

None

Command mode


Command parameters

Parameter Description<WORD> Assigns a password to the new RW or RO user account.



Avaya.com/support


Command: username lockout-time


username lockout-time

Configures the failed logon attempt lockout interval.

Syntax

default username lockout-time

no username lockout-time [enable|ssh-access|telnet-access]

username lockout-time <1-60>

Default

1 minute

Command mode


Command parameters

Parameter Description<1-60> Configure the failed logon attempt lockout interval.



Avaya.com/support


Command: username password


username password

Changes the user password.

Syntax

username password

Default

None

Command mode




Avaya.com/support


Command: username WORD


username WORD

Specifies the user name.

Syntax

username <WORD> {enable|password|ssh-access {disable|enable}|telnet-access

{disable|enable}|unlock}

Default

None

Command mode


Command parameters

Parameter Descriptionenable Enables the specified user.password Changes user's password.ssh-access Enables/Disables SSH access for user.telnet-access Enables/Disables TELNET access for user.unlock Unlock's user account.



Avaya.com/support


Command: vlacp enable


vlacp enable

Enables VLACP on a switch.

Syntax

default vlacp enable

no vlacp enable

vlacp enable

Default

Disabled

Command mode




Avaya.com/support


Command: vlacp (Ethernet InterfaceConfiguration)


vlacp (Ethernet Interface Configuration)

Configures VLACP parameters for a port.

Syntax

default [port <port>] vlacp ethertype

default [port <port>] vlacp fast-periodic-time

default [port <port>] vlacp funcmac-addr

default [port <port>] vlacp slow-periodic-time

default [port <port>] vlacp timeout

default [port <port>] vlacp timeout-scale

default vlacp [port <port>]

default vlacp [port <port>] enable

no [port <port>] vlacp funcmac-addr

no vlacp [port <port>]

no vlacp [port <port>] enable

vlacp [port <port>] enable

vlacp [port <port>] ethertype <0x8101-0x81ff | 33025-33279>

vlacp [port <port>] fast-periodic-time <400-20000>

vlacp [port <port>] funcmac-addr <H.H.H>

vlacp [port <port>] slow-periodic-time <10000-30000>

vlacp [port <port>] timeout {long | short}

vlacp [port <port>] timeout-scale <1-10>

Default

None

Command mode


Command parameters

Parameter Description[port<port>]

Specifies the port or list of ports.

enable Enables VLACP for this port. The default is disabled.ethertype<0x8101-0x81ff |33025-33279>

Sets the VLACP protocol identification for this port. The default is 8103.

fast-periodic-time <400-20000>

Sets the fast periodic time (in milliseconds) for this port. The default is 500.

funcmac-addr<H.H.H>

Sets the multicast MAC address used for the VLACPDU. Specify a MAC address in theformat H.H.H or xx:xx:xx:xx:xx:xx or xx.xx.xx.xx.xx.xx or xx-xx-xx-xx-xx-xx.

slow-periodic-time<10000-30000>

Sets the slow periodic time (in milliseconds) for a specific port type. The default is30000.

timeout{long|short}

Sets the port to use the long or short timeout: long sets the port to use the timeout-scale value multiplied by the slow-periodic-time. short sets the port to use thetimeout-scale value multiplied by the fast-periodic-time. For example, if you specify ashort timeout, set the timeout-scale value to 3, and the fast-periodic-time to 400 ms,the timer will expire within 1000 to 1200 ms. The default is long.

timeout-scale <2-10>

Sets a timeout scale for this port used to calculate the timeout. The default value is3.



Avaya.com/support


Command: vlacp hold_time


vlacp hold_time

Configures the time, in seconds, after restart to send VLACP PDUs with the subtype HOLD.

Syntax

default vlacp hold_time

no vlacp hold_time

vlacp hold_time <0-60>

Default

0

Command mode


Command parameters

Parameter Description<0-60> Specifies the hold time in seconds. Values range from 0 to 60. The default is 0.



Avaya.com/support


Command: vlacp macaddress


vlacp macaddress

Configures a Layer 2 destination multicast MAC address that global VLACP uses for the end-to-end exchange of PDUs .

Syntax

vlacp macaddress <H.H.H.H | xx:xx:xx:xx:xx:xx | xx.xx.xx.xx.xx.xx | xx-xx-xx-xx-xx-xx>

Default

None

Command mode


Command parameters

Parameter Description<H.H.H.H | xx:xx:xx:xx:xx:xx | xx.xx.xx.xx.xx.xx | xx-xx-xx-xx-xx-xx>

Specifies the MACaddress.



Avaya.com/support


Command: vlan configcontrol


vlan configcontrol

Configures control of how VLANs can be modified.

Syntax

default vlan configcontrol

no vlan configcontrol

vlan configcontrol <automatic | autopvid | flexible | strict>

Default

Strict

Command mode


Command parameters

Parameter Description<automatic | autopvid | flexible | strict> Specifies the VLAN control mode.



Avaya.com/support


Command: vlan create


vlan create

Creates and configures a new VLAN.

Syntax

no vlan create [remote-span]

vlan create <2-4094> [name <vlan_name>] type port <1-8>

vlan create <2-4094> [name <vlan_name>] type port remote-span

vlan create <2-4094> [name <vlan_name>] type protocol ipEther2 [<1-8>]

vlan create <2-4094> [name <vlan_name>] type protocol snaEther2 [<1-8>]

vlan create <2-4094> [name <vlan_name>] type protocol-decEther2 [<1-8>]

vlan create <2-4094> [name <vlan_name>] type protocol-decOtherEther2 [<1-8>]

vlan create <2-4094> [name <vlan_name>] type protocol-ipv6Ether2 [<1-8>]

vlan create <2-4094> [name <vlan_name>] type protocol-ipx802.2 [<1-8>]

vlan create <2-4094> [name <vlan_name>] type protocol-ipx802.3 [<1-8>]

vlan create <2-4094> [name <vlan_name>] type protocol-ipxEther2 [<1-8>]

vlan create <2-4094> [name <vlan_name>] type protocol-ipxSnap [<1-8>]

vlan create <2-4094> [name <vlan_name>] type protocol-Netbios [<1-8>]

vlan create <2-4094> [name <vlan_name>] type protocol-RarpEther2 [<1-8>]

vlan create <2-4094> [name <vlan_name>] type protocol-sna802.2 [<1-8>]

vlan create <2-4094> [name <vlan_name>] type protocol-Userdef ether <4096 - 65534> [<1-8>]

vlan create <2-4094> [name <vlan_name>] type protocol-Userdef llc <1 - 65534> [<1-8>]

vlan create <2-4094> [name <vlan_name>] type protocol-Userdef snap <1 - 65534> [<1-8>]

vlan create <2-4094> [name <vlan_name>] type protocol-vinesEther2 [<1-8>]

vlan create <2-4094> [name <vlan_name>] type protocol-xnsEther2 [<1-8>]

vlan create <2-4094> [name <vlan_name>] type spbm-bvlan

vlan create <2-4094> [name <vlan_name>] type spbm-switchedUni [<1-8>]

Default

None

Command mode


Command parameters


<2-4094> Creates a new VLAN with a VLAN identifier (VID) ranging in value from 2to 4094.

name <vlan_name> Assigns an alphanumeric name to the new VLAN.

type port <1-8> Specifies a port-based VLAN and assigns a Spanning Tree Group ID to theVLAN. Values range from 1 to 8.

type port remote-span

Creates a port-based, Remote Switch Port Analyzer (RSPAN) VLAN.

type protocolipEther2 [<1-8>]

Specifies a ipEther2 protocol-based VLAN. You can optionally assign aSpanning Tree Group ID to the VLAN. Values range from 1 to 8.

type protocolsnaEther2 [<1-8>]

Specifies a snaEther2 protocol-based VLAN. You can optionally assign aSpanning Tree Group ID to the VLAN. Values range from 1 to 8.

type protocol-decEther2 [<1-8>]

Specifies a decEther2 protocol-based VLAN. You can optionally assign aSpanning Tree Group ID to the VLAN. Values range from 1 to 8.

type protocol-decOtherEther2 [<1-8>]

Specifies a decOtherEther2 protocol-based VLAN. You can optionallyassign a Spanning Tree Group ID to the VLAN. Values range from 1 to 8.

type protocol-ipv6Ether2 [<1-8>]

Specifies a ipv6Ether2 protocol-based VLAN. You can optionally assign aSpanning Tree Group ID to the VLAN. Values range from 1 to 8.

type protocol-ipx802.2 [<1-8>]

Specifies a ipx802.2 protocol-based VLAN. You can optionally assign aSpanning Tree Group ID to the VLAN. Values range from 1 to 8.

type protocol-ipx802.3 [<1-8>]

Specifies a ipx802.3 protocol-based VLAN. You can optionally assign aSpanning Tree Group ID to the VLAN. Values range from 1 to 8.

type protocol-ipxEther2 [<1-8>]

Specifies a ipxEther2 protocol-based VLAN. You can optionally assign aSpanning Tree Group ID to the VLAN. Values range from 1 to 8.

type protocol-ipxSnap [<1-8>]

Specifies a ipxSnap protocol-based VLAN. You can optionally assign aSpanning Tree Group ID to the VLAN. Values range from 1 to 8.

type protocol-Netbios [<1-8>]

Specifies a NetBIOS protocol-based VLAN. You can optionally assign aSpanning Tree Group ID to the VLAN. Values range from 1 to 8.

type protocol-RarpEther2 [<1-8>]

Specifies a RarpEther2 protocol-based VLAN. You can optionally assign aSpanning Tree Group ID to the VLAN. Values range from 1 to 8.

type protocol-sna802.2 [<1-8>]

Specifies a sna802.2 VLAN. You can optionally assign a Spanning TreeGroup ID to the VLAN. Values range from 1 to 8.

type protocol-Userdef ether <4096- 65534> [<1-8>]

Specifies a userdefined protocol-based ether VLAN. Values range from4096 to 65534. You can optionally assign a Spanning Tree Group ID tothe VLAN. Values range from 1 to 8.

type protocol-Userdef llc <1 -65534> [<1-8>]

Specifies a userdefined protocol-based llc VLAN. Values range from 1 to65534. You can optionally assign a Spanning Tree Group ID to the VLAN.Values range from 1 to 8.

type protocol- Specifies a userdefined protocol-based snap VLAN. Values range from 1

Userdef snap <1 -65534> [<1-8>]

to 65534. You can optionally assign a Spanning Tree Group ID to theVLAN. Values range from 1 to 8.

type protocol-vinesEther2 [<1-8>]

Specifies a vinesEther2 protocol-based VLAN. You can optionally assign aSpanning Tree Group ID to the VLAN. Values range from 1 to 8.

type protocol-xnsEther2 [<1-8>]

Specifies a xnsEther2 protocol-based VLAN. You can optionally assign aSpanning Tree Group ID to the VLAN. Values range from 1 to 8.

type spbm-bvlan Specifies a SPBM protocol-based BVLAN.type spbm-switchedUni [<1-8>]

Specifies a SPBM switched UNI protocol-based VLAN. You can optionallyassign a Spanning Tree Group ID to the VLAN. Values range from 1 to 8.



Avaya.com/support


Command: vlan delete


vlan delete

Deletes one or more existing VLANs

Syntax

vlan delete <2-4094>

Default

None

Command mode


Command parameters


<2-4094> Specifies the VLAN identifier (VID) for the VLAN to delete. Values range from 2 to 4094.To delete multiple VLANs, you can enter a range or group of VIDs.



Avaya.com/support


Command: vlan igmp


vlan igmp

Configures IGMP for the selected VLAN.

Syntax

default vlan igmp <1-4094>

vlan igmp <1-4094> proxy <enable | disable>

vlan igmp <1-4094> query-interval <1-65535>

vlan igmp <1-4094> robust-value <2-255>

vlan igmp <1-4094> snooping <enable | disable>

vlan igmp <1-4094> v1-members add <port_list>

vlan igmp <1-4094> v1-members remove <port_list>

vlan igmp <1-4094> v2-members add <port_list>

vlan igmp <1-4094> v2-members remove <port_list>

Default

None

Command mode


Command parameters

Parameter Description<1-4094> Specifies the VLAN identifier (VID).proxy <enable |disable>

Enables or disables VLAN proxy for the selected VLAN.

query-interval<1-65535>

Sets the frequency, in seconds, at which host query packets are transmitted onthe selected VLAN. Values range from 1 to 65535. The default is 125.

robust-value<2-255>

Set the robustness value for the selected VLAN. Values range from 2 to 255.The default is 2.

snooping <enable| disable>

Enables or disables IGMP snooping for the selected VLAN.

v1-members {add<port_list>}

Adds one or more IGMPv1 static multicast router (mrouter) ports to theselected VLAN.

v1-members

{remove<port_list>}

Removes one or more IGMPv1 static multicast router (mrouter) ports from theselected VLAN.

v2-members{remove<port_list>}

Removes one or more IGMPv2 static multicast router (mrouter) ports from theselected VLAN.



Avaya.com/support


Command: vlan igmp unknown-mcast-allow-flood


vlan igmp unknown-mcast-allow-flood

Adds addresses to respective lists of MAC addresses and IP addresses that can flood VLANs with unknown multicast packets.

Syntax

Default

None

Command mode


Command parameters


<1-4094> Specifies the VLAN identifier (VID) of the VLAN to flood with unknown multicast packets..Values range from 1 to 4094.



Avaya.com/support


Command: vlan igmp unknown-mcast-no-flood


vlan igmp unknown-mcast-no-flood

Deletes addresses from respective lists of MAC addresses and IP addresses that can flood VLANs with unknown multicast packets.

Syntax

Default

Disabled

Command mode


Command parameters


<1-4094> Specifies the VLAN identifier (VID) of the VLAN to discontinue flooding with unknownmulticast packets. Values range from 1 to 4094.

<enable |disable>

When enabled, deletes addresses from respective lists of MAC addresses and IPaddresses that can flood VLANs with unknown multicast packets.



Avaya.com/support


Command: vlan i-sid


vlan i-sid

Creates or removes a C-VLAN.

Syntax

default vlan i-sid <1-4094>

no vlan i-sid <1-4094>

vlan i-sid <1-4094>

Default

None

Command mode


Command parameters

Parameter Description<1-4094> Specifies the VLAN identifier (VID) of the C-VLAN. Values range from 1 to 4094.



Avaya.com/support


Command: vlan members


vlan members

Adds port members to or removes port members from one or more specific VLANs.

Syntax

<1-4094> <port_list>

add <1-4094> <port_list>

no vlan members

remove <1-4094> <port_list>

Default

None

Command mode


Command parameters


<1-4094> <port_list> Specifies one or more switch ports to add as members to theselected VLAN.

add <1-4094> <port_list> Specifies one or more switch ports to add as members to theselected VLAN.

remove <1-4094><port_list>

Specifies one or more port members to remove from the selectedVLAN.



Avaya.com/support


Command: vlan mgmt


vlan mgmt

Sets the management VLAN.

Syntax

default vlan mgmt <1-4094>

vlan mgmt <1-4094>

Default

None

Command mode


Command parameters




Avaya.com/support


Command: vlan name


vlan name

Assigns an alphanumeric name to an existing VLAN.

Syntax

default vlan name <1-4094>

vlan name <1-4094> <vlan_name>

Default

None

Command mode


Command parameters


<1-4094> Specifies the VLAN identifier (VID) of the VLAN to assign the name. Values range from1 to 4094.

<vlan_name> Specifies an alphanumeric name for the VLAN.



Avaya.com/support


Command: vlan ports


vlan ports

Configures VLAN associated switch ports.

Syntax

default vlan ports name <port_list>

no vlan ports name <port_list>

vlan ports <port_list> filter-unregistered-frames {enable | disable}

vlan ports <port_list> filter-untagged-frame {enable | disable}

vlan ports <port_list> name <port_name>

vlan ports <port_list> priority <0-7>

vlan ports <port_list> pvid <1-4094>

vlan ports <port_list> tagging {enable | disable | tagAll | untagAll | tagPvidOnly |

untagPvidOnly}

Default

None

Command mode


Command parameters


<port_list> Specifies one or more VLAN member ports toconfigure.

filter-unregistered-frames {enable |disable}

Enables or disables the port to filter receivedunregistered packets.

filter-untagged-frames {enable |disable}

Enables or disables the port to filter receiveduntagged packets.

name <port_name> Specifies an alphanumeric name for the port.

priority <0-7>Sets the port as a priority for the switch to consideras it forwards received packets. Values range from0 to 7.

pvid <1-4094> Sets the PVID of the port to the specified VLAN.Values range from 1 to 4094.

tagging {enable | disable | tagAll| untagAll | tagPvidOnly | Enables or disables the port as a tagged VLAN

untagPvidOnly}member for egressing packet.



Avaya.com/support


Command: vlan remote-span


vlan remote-span

Enables or disables Remote Switch Port Anaylzer (RSPAN) on one or more VLANs

Syntax

no vlan remote-span <1-4094>

vlan remote-span <1-4094>

Default

None

Command mode


Command parameters


<1-4094> Specifies one or more VLANs for which to enable or disable RSPAN. Values range from 1to 4094.



Avaya.com/support


Command: web-server


web-server

Enable the web management interface to provide management access to the switch using a web browser.

Syntax

no web-server

web-server <disable | enable>

Default

Enabled

Command mode


Command parameters

Parameter Description<disable | enable> Disables or enable web access.



Avaya.com/support


Command: write memory


write memory

Writes the configuration in NVRAM.

Syntax

write memory

Default

None

Command mode

Privileged EXEC



Avaya.com/support


Avaya Command Line Interface Commands Reference

Documents

Transcript of Avaya Command Line Interface Commands Reference