AUSTRALIAN ENVIROBLAST PTY LTD

abrasive blasting cleaning

paint removal restoration

www.australianenviroblast.com.au

Abrasiive blasting is effective on a wide range of surfaces and structures around the home and in the garden

www.australianenviroblast.com.au

What is abrasive blasting?

Abrasive blasting is: ] fast ] efficient ] safe ] effective ] EPA approved

Abrasive blasting (sometimes known as sand blasting) is a safe, environmentally-friendly and cost effective way of removing rust, grease, paint, stains, and other types of coatings, corrosion and residue from almost any type of surface. It is also an effective means of smoothing, roughing up, or reshaping different types of surfaces and structures, and can also be used to create decorative finishes on concrete.

During the process, abrasive material is propelled by at high pressure (powered by air or water) onto the surface or structure to be cleaned, and this strips away unwanted substances but leaves the original surfaces clean and contaminant free. Different types of abrasive materials (or media) can be used according to the objects or areas that need to be cleaned. These

include sand, metallic grit, shot, stone granulate, garnet, glass, chalk or soda. After abrasive blasting has been completed, surfaces and structures are extremely clean and are prepared ready for protective coatings to be re-applied or repainting to take place.

The media used during abrasive blasting is reclaimed, as is any water used during wet abrasive blasting, while there is no dust produced during the process. Therefore, using the Quill Falcon Precision Dustless Kwikblast® System means that this process does not cause environmental damage nor consume excessive natural resources, as there is significantly less dust and waste produced, and water used.

At Australian Enviroblast, we are able to offer a full range of abrasive blasting services, all designed to meet the specific requirements of any job, no matter how large or small, or however delicate. Our mobile on site service means that we can travel to you, and we also have a facility at Seaford equipped with blasting and spray booths.

Applications

before

Abrasive blasting can be used in a wide variety of applications, and is as well-suited to tackling domestic and small-scale jobs as it is commercial projects, and it’s ideal for use in tight, out of the way places as well as on large surfaces.

Around the home, abrasive blasting can be used for an enormous variety of cleaning, restoration and refurbishment work, and is entirely safe to employ in a domestic setting. It can also be used to create a non-slip surface on concrete, or to create textured finishes.

after

Steel ] verandahs and carports ] gates ] lattice work ] trellises ] fences ] sheds ] pipes ] staircases ] beams

Brick ] exterior walls ] fences ] renderings ] sandstone

Stone ] paving stones ] exterior walls ] fences ] garden statues or sculptures

Cement and concrete ] driveways ] patios ] verandahs ] architectural concrete

Swimming pools ] pool floors ] pool walls ] pool surrounds

Wood ] decking ] outdoor furniture

Trailers ] boat trailers ] car trailers ] horse floats ] box trailers ] motor bike trailers

Boats ] cleaning hulls ] preparation for repainting

Cars ] strip paint from bodywork ] clean car chassis ] clean car parts

Bikes ] motorbike frames ] bicycle frames

Machinery ] industrial machinery ] agricultural machinery

Any other application that requires a surface to be prepared for painting or coating

Applications

Australian Enviroblast hard

at work cleaning an Adelaide

swimming pool

Heritage brickwork comes up especially well after abrasive blasting, and can be restored it to its former glory

before

after

Concrete is cleaned very effectively by abrasive blasting, as demonstrated here at the University of Adelaide, where the tannin

covering the wood on this outdoor seating had streaked and discoloured the concrete base below.

before

after

www.australianenviroblast.com.au

About UsAustralian Enviroblast was founded in 2009 by Mark Chiappin with the aim of introducing environmentally-friendly abrasive blasting serves to Australia.

Using the revolutionary and technologically-advanced Quill Falcon Precision Dustless Kwikblast® System, the Australian Enviroblast team of trained and skilled operators is able to remove a wide range of coatings, corrosion and residues from all types of structures, locations and equipment, while leaving surfaces clean and contaminant free. We have vast experience of jobs both large and small, in the commercial and the domestic fields.

Australian Enviroblast is able to offer a full range of services, including: ] wet abrasive blasting ] dry abrasive blasting ] mechanical preparation ] UHP (pressure cleaning) ] industrial coatings

With a fleet of mobile equipment, Australian Enviroblast is able carry out on-site abrasive blasting and industrial coating, and offers efficient, flexible and cost-effective solutions that deliver outstanding results on

both large-scale and more intricate, delicate jobs. Furthermore, the Quill Falcon Precision Dustless Kwikblast® System is extremely safe and requires no encapsulation, meaning that other work can be carried out at the same time, saving both time and money.

Australian Enviroblast is licensed by the Environmental Protection Agency and adheres to its high standards of environmental safety with regards to air quality, noise, water quality and waste management. The company has won contracts in both the public and private sectors, including markets such as oil, gas, shipping, construction and the highways, and also has an impressive portfolio of domestic and small-scale abrasive blasting jobs, including: ] rust removal ] paint removal ] graffiti removal ] stain removal ] driveway and decking cleaning ] steel and fibreglass cleaning

AUSTRALIAN ENVIROBLAST PTY LTD

www.australianenviroblast.com.auinfo@australianenviroblast.com.au

tel: 0458 455668

Contact Us