Product Description Au.diPanel offers our widest selection of perforation options and a choice of substrates. Combined with our range of decorative surface finishes and our Integrated Acoustic Backing (IAB), Au.diPanel lends itself to tailoring for specific appearance or acoustic performance requirements.

Product Features– Standard range of pre-finished timber grain and

decorative surfaces– Largest selection of perforation patterns– Panel sizes up to 3600 x 1200mm – Veneers can be nominated to co-ordinate with

other timber building elements or furnishings– Higher impact-resistance obtained with

plywood panels

Variations – Optional face veneer to your specifications– Range of standard perforation patterns or custom

patterns – Range of standard side and end margins or custom

margins – Edge profiling and face detailing of panels

available to specification– Integrated Acoustic Backing (IAB)– Graphic images achievable

Jointing Options– Vee Joint– Expressed Joint

(Where expressed joints are selected, allowance should be made for dressing of panel edges)

Material Sizes Au.diPanel is available uncoated or pre-finished in our select range of decorative surface finishes in the following sizes. For non-standard sizes, consult Atkar Technical Staff.

Natural timber veneers in lengths over 2400mm are limited and subject to current availability.

Performance AcousticDiversity of perforation options allow for open area of panel to range from 2.47% up to 34.51 % nominally.

Open Area Guide

Au.diPanel data sheet

© Copyright 2018 GroupAtkar

TM

WA/SAPOT 5662 6323 08

6919 DC Joondalup 710 Box Region Head Office

17–19 David Lee Road Hallam Victoria 3803 PO Box 1143 Narre Warren MDC 3805 T 03 9796 3333 atkar.com.au

with Graphic Au.diPanel

ApplicationsWalls ceilings and

Substrates–––––– OSB

Plywood resistant moisture MDF

rated fire Blackcore / Blackcore MDF rated fire MDF standard MDF

FireFor Atkar. contact please ratings fire Number Group

Rating

WarrantyAu.diPanel

terms. for document warranty to Refer years. (15) fifteen for warranted is

Fixing–––– fix Face

(ceilings) fix concealed PS3 Au.diMount (walls) fix concealed XJ1 Au.diMount (walls) fix concealed BJ2 Au.diMount

Systems

NRC 0.8 to up value

Finish

– Inluxe– Inluxe– Inluxe– Inluxe Colour

Laminate Image Veneer

Options

Document 3 Version

Margin Options Standard

possible. sizes margin Other 25mm. is margin perimeter

Perforation Patterns Available

patterns

MDF

12.0mm. and 10.0mm 8.0mm, 6.0mm, :sizes perforation following

the for used be can substrate rated fire

Staff. Technical Atkarconsult sizes, perforation and patterns

custom For below. detailed as of selection a in diameter 57.0mm to 4.5mm from ranging sizes perforation with

Au. Paneldi data sheet

© Copyright 2018 GroupAtkar

Product AP125S Type Product AP125D Type

Product AP250S Type Product AP250D Type

Product AP500S Type Product AP1000S Type

Document 3 Version

Accesseasily

shouldtheplanks

machined

Standard

request. on available sizes Custom 600mm. x 600 450mm, x 450 sizes: panel access

to. mounted be to services for installed insert matching solid custom a and

left be can space width plank 3 or 2 a Alternatively installed. they’re once the into cut be

can penetrations Service planks. of installation the during on-site out carried be processes

These Au.diPanel. intointegrated be can penetrations ceiling other and panels

Access Panels

Vee Joint* Timber Batten or Stud

Expressed Joint Timber Batten or Stud

Bevel Panel Edges

Acoustic Insulation(optional)

Integrated AcousticBacking or selectedscrim shown dotted

*Vee jointing may create difficulties with panel and perforation alignment

Au.diPanel

Acoustic Insulation(optional)

Integrated AcousticBacking or selectedscrim shown dotted Au.diPanel

BackingStrip

Attention – The method of fixing indicated for this product is of a general nature only and does not allow for specific design criteria such as wind loads, expansion joints or any other special design requirements which should be separately provided for by the It

secured. firmly are panels ensure to responsibility installers the is

specifier.

Due to continual product improvement the information in this publication is subject to alteration without notice.

Jointing Details

* For other thicknesses consult Atkar Technical Staff.

used. be to fixings discrete more enable to recommended are members To

framing

minimise the risk of buckling, it is recommended that the panels be allowed to acclimatise in the area in which they are to be installed. This is best achieved by standing individual panels loosely around the room and allowing air to freely circulate around them for several days prior to fixing. Allowance should be made between panels to accommodate swelling and building movement.

Au.diPanel installation guide

© Copyright 2018 GroupAtkar

Au.diStyle Au.diStyle Au.diStyle Au.diStylePanelAu.di

Wall frame Batten or Stud Batten or Stud Batten or StudWall frame

Edge profile/finish as selectedEdge profile/finish as selectedExposed fasteners as selected

Exposed fasteners as selectedBevel panel edges

Edge profile/finish as selectedMax. joint width

5

Expressed Joint – Plan view Au.diMount Concealed Fixing System (Refer to Installation System - XJ1)

Butt Joint System Typical detail refer to Au.diMount BJ2 System for full details

Wall Frame

AMCC061screwed to wall frame

AMCO61screwed to rear of panel

Panel

Panel

Panel

Panel

4

3

2

5

1

Installation Details The following table provides a fixing guide for general residential and commercial applications. Panels can be face fixed or conceal fixed. Refer to Au.diMount data sheets for applicable concealed fixing systems.

Consideration should be given to reduced framing centres for higher impact areas such as corridors and crowded spaces, or where surfaces are to be curved. Au.diPanel wall panels should be installed with a full perimeter support and plywood ceiling panels must have the face grain running at right

timber fixed, face be to are panels If members. framing to angles

Concealed Fixings Expressed Joint Typical detail refer to Au.diMount

XJ1 System for full details

A

advice. further for engineer

acoustican consult Please performance. acoustic optimal

achieve to recommended is gap air 90mm

FaceConcealed

available. options for Atkar Consult required. as head screw

ixF

Document 3 Version

General fixing details. full for Atkar consult applications, interior for only, guide

Typical System details full for PS3 Au.diMount to refer detail