01

All rights reserved © Baicells Technologies Co., Ltd.

ATOM OD06 - EG7010C USER Manual

2

1. Shipping List

Make sure you have got the following parts:

EG7010C Quick Guide

PoE Adapter Power Cord

Standard Mounting Kits

Optional Mounting Kits

2. Hardware Introduction

2.1 Indicators

Identity Description Color Status Description

MIU

-

Yellow OFF Reserved.

Steady On Reserved.

Blanking Reserved.

LTE Network state

Indicator Blue OFF LTE disconnected.

Steady On LTE connected.

SIM SIM card

status

indicator

Yellow Steady On The SIM card is normal.

Blanking The SIM card is abnormal or not

inserted.

LAN 100Mbps Eth

Indication

Yellow OFF Ethernet connection does not

established.

Steady On Ethernet connection is normal.

Blanking Data is transmitting.

PWR Power

Indicator

Yellow OFF No Power Supply

Steady On Power On

LTE

Signal

5 LTEs,

Indicate

Green All OFF Signal is too weak to attach.

Steady On According to signal strength in turn light

Identity Description Color Status Description

connection

state and

signal

strength

up

Blanking Scanning the LTE network

The CPE is authenticating.

CPE is getting IP address from the LTE

network.

2.2 Interface and Buttons

Interface & Button Description

PoE Connected to the PoE Power Adapter

TF Support SD card

SIM Support 1.8V/3.0V USIM 2FF

RESET Long press over 10 seconds to restore the factory settings

GND Connected to Earth by conductor

3. Installation Guide

3.1 Support Materials

Before installation, prepare the following support materials accordingly, as given below:

Item Description

Ethernet cable Outdoor Shield CAT5E

Shorter than 330 feet

Ground wire 16mm² yellow-green wire

3.2 Install USIM Card and Cables

(1) Screw the screw on the waterproof

cover, and open the waterproof cover

(2) Insert the USIM card to the USIM

slot. Note following the directions

(3) Connect the Ethernet cable to the PoE

port

(4) connect the ground cable to the

ground screw

(5) Close the waterproof cover and fasten the screw on the cover.

(6) Connected Ethernet cable to the power adapter.

Pay attention to the power adapter interface directions.

(7) Power on, the LED indicator will light up.

4. Configuration Guide

4.1 4.1 Login

The CPE manages, configures, and maintains the device by web management page. The

steps to log in are as follows:

1. In the address column of browser, type in http://192.168.150.1, then press “Enter”:

2. Enter the user name and password, click "LOGIN". After password authentication,

you can log on to the web management page.

The default user name and password is admin.

For security, it is recommended that you open the firewall, and keep your login password,

WLAN FTP passwords and password well.

4.2 View Status

In the overview area, you can view the device information and LTE status,such as Product

name, Software version, PLMN, IMSI, RSRP, RSRQ, CINR, SINR, Tx Power, Cell ID, PCI,

and so on, as shown below:

5. Specifications

Basic Specifications

Item Description

UE-Category 3GPP R10, CAT 6/7

USIM Slot 1.8V/3.0V USIM 2FF

Ethernet Port 1 RJ45, LAN, 10/100/1000 auto-sensing, auto-MDX,

PoE

Power Supply Input: Universal range 100V~240V AC

Output: PoE (24V DC, 0.5A)

Reset Button Tactile button. Long press over 10s to restore the

factory settings

LED Indicators MIU/LTE/SIM/LAN/PWR/LTE Signal

Dimensions 241mm (H) x 154mm (W) x 50mm (D)

Weight About 900 g

LTE Specifications

Item Description

LTE Mode LTE-TDD

LTE Bands Band 43

TXRX 2T4R

Channel Bandwidth 5MHz, 10MHz, 15MHz, 20MHz

Modulation QPSK, 16QAM

Receive Sensitivity -94dBm @ QPSK,20MHz, 25°C

MAX Output Power 19±2dBm

Antenna Type Internal directional-antenna

Antenna Gain 10dBi@3.xGHz, 2 Ports

Polarization ±45°

Antenna Efficiency >70%

Isolation ≤-25dB

VSWR ≤2

Horizontal Beam Width (3dB) 60±3°@3.xGHz, 2 Ports

Vertical Beam Width (3dB) 25±5°@3.xGHz, 2 Ports

WiFi Specifications (Just for Alignment)

Item Description

Standard IEEE 802.11b/g/n

Channel Bandwidth 20MHz

Frequency 2.4GHz

TXRX 1T1R

Peak Rate

802.11b: 11Mbps

802.11g: 54Mbps

802.11n: 300Mbps

Modulation DSSS/CCK, OFDM

Receive Sensitivity

-64 dBm@65Mbit/s, typical for 802.11n

-65 dBm@54Mbit/s, typical for 802.11g

-76 dBm@11Mbit/s, typical for 802.11b

MAX Output Power 15±2dBm

Antenna Type Internal omni-antenna

Antenna Gain 0dBi

SW Specifications

Item Description

Language Support English/Chinese

Network Mode NAT/Bridge/Tunnel

IP Protocol IPv4/IPv6

SIM Management PIN Management, SIM Lock

Network Connection Management Auto/Manual

LTE Scan Mode Full band scan, Frequency Lock

WLAN

WPS

MSSID Isolation

VLAN

VPN L2TP

GRE

NAT

Port forwarding

DMZ

ALG

Port Trigger

Firewall

IP/MAC/URL Filter

Access Control

Block Port Scanner / SYN Flood

SPI Filter

Network Management TR069

SNMP

Diagnostics

TCPDump

Ping

Trace route

Statistics

LTE Status/Connection Time/System Up Time

Device Status

DHCP Client List

WiFi Station List

LTE Status

Firewall Status

Maintenance

Date & Time setting

Reboot

Restore factory settings

Restore / Back up configuration file

Firmware upgrade locally/OTA (over the air)

System Log

Operating Log

Run-time Log

Filter/Select/Display/Export Log

Environmental Specifications

Item Description

Operating Temperature -40°C to 55°C

Storage Temperature -40°C to 70°C

Operating Humidity 5% to 95%

Ingress Protection Rating IP65

1

6. Regulatory Compliance

FCC Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void

the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

Warning:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm between the radiator &

your body.

2

ISEDC Compliance

This device complies with Innovation, Science, and Economic Development

Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) This device may not cause interference, and

(2) This device must accept any interference, including interference that may cause undesired opera

tion of the device.

Le présent appareil est conforme aux CNR d' Innovation, Science et Développement

économique Canada applicables aux appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions

suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d'en compromettre le fonctionnement.

The antenna(s) used for this transmitter must be installed to provide a separation distance of at least

20cm from all persons and must not be collocated or operating in conjunction with any other antenna

or transmitter, End-Users must be provided with transmitter operation conditions for satisfying RF

exposure compliance.