Atom OD0406-14/19.5 User Manual

February 2018

Version 1.3

2

About This Document This document is intended installers and users of the Baicells Atom OD04/06-14 or Atom OD04/06-19.5 outdoor user equipment (UE). The information covers how to install, set up, and use the outdoor UEs for broadband wireless access to Long-Term Evolution (LTE) carrier networks.

Copyright Notice Baicells Technologies, Inc., copyrights the information in this document. No part of this document may be reproduced in any form or means without the prior written consent of Baicells Technologies, Inc.

Disclaimer The information in this document is subject to change at any time without notice. For more information, please consult with a Baicells technical engineer or the support team. Refer to the “Contact Us” section below.

Revision Record Date Version Description SMEs/Contributors Writer/Editor 21-Feb-2018 V1.3 Updated for CAT 6 Cameron Kilton

Rick Harnish Sharon Redfoot

Dec 2017 V1.1, V1.2

Draft Yang Yanan Cameron Kilton Rick Harnish

Sharon Redfoot

Contact Us Baicells Technologies Co., Ltd.

China North America

Address: 3F, Bldg. A, No. 1 Kai Tuo Rd, Haidian Dist, Beijing, China

Address: 555 Republic Dr., #200, Plano, TX 75074, USA

Phone: +86-10-62607100 Phone: +1-888-502-5585

E-mail: contact@Baicells.com Email: sales_na@Baicells.com or support_na@Baicells.com

Website: www.Baicells.com Website: https://na.Baicells.com

3

Table of Contents

1 Introduction .................................................................................................................. 5

2 Parts & Materials .......................................................................................................... 7

3 Description ................................................................................................................... 9

4 Installation Procedures ................................................................................................ 12

5 Basic Configuration...................................................................................................... 18

5.1 Log in and Change the Password ............................................................................... 18

5.2 Configure Network Mode .......................................................................................... 19

5.3 Configure LTE Connection Setting ............................................................................. 19

5.4 Configure Scan Mode ................................................................................................ 20

5.5 Configure APN Management ..................................................................................... 22

Appendix A: Atom OD04/06-14 Technical Specifications .................................................. 25

Basic Specifications .......................................................................................................... 25

RF Specifications .............................................................................................................. 25

Wi-Fi Specifications ......................................................................................................... 27

Software Specifications ................................................................................................... 27

Environmental Specifications .......................................................................................... 28

Global Part Numbers ....................................................................................................... 28

Appendix B: Atom OD04/06-19.5 Technical Specifications ............................................... 29

Basic Specifications .......................................................................................................... 29

RF Specifications .............................................................................................................. 29

Wi-Fi Specifications ......................................................................................................... 31

Software Specifications ................................................................................................... 31

Environmental Specifications .......................................................................................... 32

Global Part Numbers ....................................................................................................... 32

Appendix C: CE Statement .............................................................................................. 33

Appendix D: FAQs .......................................................................................................... 34

List of Figures Figure 1-1: Baicells Broadband Wireless Access System ........................................................... 5 Figure 3-1: Atom OD04/06-14 ................................................................................................... 9 Figure 3-2: Atom OD04/06-19.5 ................................................................................................ 9 Figure 3-3: LEDs and Interfaces ............................................................................................... 10 Figure 4-1: Atom OD04/06-14/19.5 Installation ...................................................................... 12 Figure 4-2: Anti-Slip Rubber .................................................................................................... 13 Figure 4-3: Bracket ................................................................................................................... 13 Figure 4-4: Install Unit on Bracket ........................................................................................... 13 Figure 4-5: Tighten Bracket ...................................................................................................... 14 Figure 4-6: Threaded Rod ........................................................................................................ 14 Figure 4-7: Attach Omegas ...................................................................................................... 15

4

Figure 4-8: Remove Bracket ..................................................................................................... 15 Figure 4-9: Fix Bracket to Wall ................................................................................................. 16 Figure 4-10: Install Unit ........................................................................................................... 16 Figure 4-11: Mark Drilling Locations ........................................................................................ 16 Figure 4-12: Install Bracket ...................................................................................................... 17 Figure 4-13: OD04/06-19.5 Grounding .................................................................................... 17 Figure 5-1: Log in to CPE GUI ................................................................................................... 18 Figure 5-2: Change Account Information ................................................................................ 19 Figure 5-3: Network Mode ...................................................................................................... 19 Figure 5-4: LTE Settings ............................................................................................................ 20 Figure 5-5: Scan Mode ............................................................................................................. 20 Figure 5-6: PCI Lock Settings .................................................................................................... 21 Figure 5-7: Band/Frequency Preferred Settings ...................................................................... 22 Figure 5-8: APN Management Settings ................................................................................... 23

List of Tables Table 2-1: Parts .......................................................................................................................... 7 Table 2-2: Materials ................................................................................................................... 8 Table 3-1: LEDs ......................................................................................................................... 11 Table 3-2: Interfaces ................................................................................................................ 11 Table 5-1: APN Management Settings ..................................................................................... 23

5

1 Introduction The Baicells Atom OD04/06-14 and OD04/06-19.5 outdoor user equipment (UE) is part of the Baicells broadband wireless access system that integrates with carrier networks based on Long-Term Evolution (LTE) technology. The Baicells system allows telecom operators, service providers, and enterprises to bring broadband data and voice services to customers or employees, even in challenging environments such as rural locations.

The outdoor UE serves as a gateway between the user’s computers or other smart devices and the carrier network by communicating wirelessly with the service provider’s LTE eNodeB’s (eNB) at cell sites located in the region (Figure 1-1). The eNBs communicate with the carrier network, providing the user with internet access.

The user-friendly, plug-and-play design behind the Atom UE makes it quick and easy to install, configure, and use. And because it is carrier-grade equipment, the UE is built for endurance and the ability to adapt newer LTE technologies as they evolve.

Figure 1-1: Baicells Broadband Wireless Access System

Note: The terms user equipment (UE) and customer premise equipment (CPE) are used interchangeably in the GUIs and documentation. Likewise, the terms eNodeB (eNB) and base station are used interchangeably.

6

Following is a list of the key features of the Atom OD04/06-14 and OD04/06-19.5 UEs. Exact specifications vary by model: (Refer to the technical specifications in Appendix A for Atom OD04/06-14 and Appendix B for Atom OD04/06-19.5.)

• Support standard LTE FDD and TDD bands and comply with 3GPP Release 9 CAT4 or Release CAT 6/7 standards

o FDD: Band 7

o TDD: Bands 38, 40, 41, 42, 43, 48, and customized

• Ethernet interface:

o OD04: 100 Mbps

o OD06: 1000 Mbps

• Local and Web based GUI, TR069 network management protocol, Baicells Operations Management Console (OMC)

• Integrated bipolar directional high-gain LTE antenna

• Cell lock, SIM lock, and Pin lock

• User-friendly LEDs

• Power supply using Power Over Ethernet (PoE)

• Pole or wall mount options

• Wi-Fi assisted alignment

7

2 Parts & Materials Refer to Table 2-1 for a list of the components that you should receive with the Baicells Atom OD04/06-14 or OD04/06-19.5 user equipment (UE).

Table 2-1: Parts

Item Qty Picture

Atom OD04/06-14 or Atom OD04/06-19.5 unit

1

Power Cable 1

PoE Power Adaptor 1

Atom OD04/06-19.5 Mounting Bracket

1 each

User Manual 1 -

8

You will need standard tools, Ethernet cable, and RJ-45 connectors to cable the outdoor unit to the indoor LAN equipment. The cable length will depend on where the UE will be placed externally. Refer to Table 2-2.

Table 2-2: Materials

Item Description

Ethernet Cable Outdoor shield CAT5E

Shorter than 330 feet

Ground Wire 16mm2 yellow-green wire

9

3 Description The Baicells Atom OD04/06-14 and OD04/06-19.5 models of user equipment (UE) are powerful, outdoor, standards-based devices designed to connect seamlessly to any standard Long-Term Evolution (LTE) eNodeB (eNB) operating on the same frequency band. The devices have a small, sleek form factor (Figures 3-1 and 3-2), yet are ruggedized for the most challenging outdoor environments. Refer to Appendix A for the technical specifications.

Figure 3-1: Atom OD04/06-14

Figure 3-2: Atom OD04/06-19.5

10

Looking further at the unit (Figure 3-3) you will see LED indicators on the side and interfaces on the side, back, and bottom of the unit. The LEDs are explained in Table 3-1, and the interfaces are described in Table 3-2.

Figure 3-3: LEDs and Interfaces

11

Table 3-1: LEDs

LEDs vary by model – not all models will have all of the LEDs listed below.

Identity Description Color Status Description

MIU - Yellow Off Reserved.

Steady On Reserved. Blinking Reserved.

LTE LTE network status indicator

Blue Off

The unit is not connected to the LTE network.

Steady On The unit is connected to the LTE network.

SIM

Universal Subscriber Identification Module (USIM) card status indicator

Yellow

Steady On The USIM card is functioning normally.

Blinking The USIM card is not inserted or is not functioning normally.

LAN 100 or 1000 Mbps Local Area Network Ethernet indicator

Yellow Off No Ethernet connection established

Steady On Ethernet connection is normal Blinking Data is transmitting

PWR Power indicator Yellow Off No power supply to the unit

Steady On Power to the unit is on

LTE Signal

1, 2, 3, 4, or 5 bars to indicate connection status and signal strength. The more bars, the stronger the signal between the CPE and a network cell.

Green

All Off The signal is too weak for the unit to connect to the LTE network.

Steady On Bars will light steadily according to signal strength

Blinking

The unit is scanning the LTE network. The unit is authenticating with the network. The unit is getting an IP address from the LTE network.

Table 3-2: Interfaces

Interfaces vary by model – not all models will have all of the interfaces listed below.

Interfaces Description PoE The Power over Ethernet (PoE) power adaptor is connected to the

unit. TF or SD Slot Card slot for a secure digital (SD) card SIM/USIM Slot Universal Subscriber Identity Module card slot, 1.8V/3.0V USIM 2FF RESET Press the reset button for at least 10 seconds to restore the UE to its

factory settings. GND Ground lug. The unit is connected to Earth by conductor.

12

4 Installation Procedures Follow the steps below to install the Atom OD04/06-14 or OD04/06-19.5 user equipment (UE).

1. Prepare the Ethernet cable, per section 2 Parts & Materials. The Ethernet cable will run from the outside Atom unit to the inside of the facility, where the unit connects to the LAN. Cable length will vary by location.

2. Loosen the screws on the Atom’s waterproof cover, and open the cover.

3. Connect the Ethernet cable to the PoE port on the unit. Connect the other end to the power adaptor. Refer to Figure 4-1.

4. Follow the instructions on the SIM/USIM card to insert it in the Atom unit.

Attention: Do not power on the unit while installing or uninstalling the SIM/USIM card. Doing so could damage the card and the unit.

5. Close the Atom unit’s waterproof cover, and tighten the screws.

6. Atom OD04/06-14: Connect the ground cable to the ground screw. (NOTE: The Atom OD04/06-19.5 grounding information is covered in step 11.)

7. Plug the power adaptor into an electrical outlet. Pay attention to the power adaptor interface directions noted on the adaptor itself. The LED indicators should light up.

Figure 4-1: Atom OD04/06-14/19.5 Installation

13

8. Mount the Atom unit. If you are installing the unit on a pole, e.g., to attach to a roof, follow the instructions provided in step 9. If you are installing the unit on an outside wall, follow the instructions provided in step 10.

9. Pole installation:

a. Atom OD04/06-14:

a1) Round an anti-slip rubber band on the pole (Figure 4-2).

Figure 4-2: Anti-Slip Rubber

a2) Fix the bracket over the band using the hoop (Figure 4-3).

Figure 4-3: Bracket

a3) Install the unit on the bracket, and tighten the screw (Figure 4-4).

Figure 4-4: Install Unit on Bracket

b. Atom OD04/06-19.5:

b1) Tighten four M6 screws at the bottom of the bracket (Figure 4-5).

14

Figure 4-5: Tighten Bracket

b2) Install the threaded rod to the bracket (Figure 4-6).

Figure 4-6: Threaded Rod

b3) Hold the assembly up to the pole. Attach the two omegas to the threaded rods with M8 nuts, and tighten them (Figure 4-7).

15

Figure 4-7: Attach Omegas

b4) Proceed to step 11 for grounding.

10. Wall installation:

a. Atom OD04/06-14:

a1) Slip the bracket off of the Atom unit, and fit the unit on the wall to mark the drilling locations (Figure 4-8).

Figure 4-8: Remove Bracket

a2) Drill four 10-mm diameter and 70-mm depth holes in the wall, following the marked locations.

a3) Check the up/down direction of the bracket, and then fix it on the wall using the M5 tapping screws (Figure 4-9).

16

Figure 4-9: Fix Bracket to Wall

a4) Install the unit to the bracket, and tighten the screws (Figure 4-10).

Figure 4-10: Install Unit

b. Atom OD04/06-19.5:

b1) Put the bracket on the wall, and mark the drilling locations (Figure 4-11).

Figure 4-11: Mark Drilling Locations

b2) Drill two 12-mm (0.5-in) diameter and 80-mm (3.1-in) depth holes on the marked locations.

b3) Install the expansion bolts on the hole with a hammer.

b4) Install the bracket on the expansion, and tighten the screws (Figure 4-12).

17

Figure 4-12: Install Bracket

b5) Proceed to step 11 for grounding.

11. Grounding the Atom OD04/06-19.5: The unit must be grounded. Using the grounding cable, connect the grounding screw to the ground row shown in Figure 4-13.

Figure 4-13: OD04/06-19.5 Grounding

18

5 Basic Configuration To configure the Atom outdoor user equipment (UE), you will access the local or Web-based GUI application. Follow the steps provided to log in and complete the minimal configuration requirements for the UE to operate. For more detailed configuration information, refer to the Baicells Configuration and Network Administration Guide on the Baicells support website.

NOTE: If your service provider pre-configured the device with a CloudKey, the device may already be configured in the network.

5.1 Log in and Change the Password

Follow the steps below to access and log in to the UE GUI application.

1. Connect the UE power. 2. Open a Web browser, and in the address bar type http://192.168.254.1

(or http://192.168.1.1 if on older firmware than V1.0.3) and then press Enter. The login window should appear as shown in Figure 5-1. Figure 5-1: Log in to CPE GUI

3. Enter the default user name (admin) and password (admin), and click on the Login

button. The first window you will see is called the overview. The overview is a dashboard showing the product name, software version, and operational information. All of the UE GUI windows and fields are explained in the Baicells Configuration & Network Administration Guide, found on the Baicells support website.

4. After you log in, you should change the default password to a secure password. You can find the account fields under System > Account (Figure 5-2).

19

Figure 5-2: Change Account Information

5.2 Configure Network Mode

1. Choose Network > Network Mode. Choose either Network Address Translation (NAT), Router, or Bridge mode (Figure 5-3) according to your LTE network setup.

Figure 5-3: Network Mode

2. Click on Submit to save your selection.

5.3 Configure LTE Connection Setting

1. Choose Network > LTE Settings to choose the LTE connection setting for this UE as either Auto connect or Manual connect (Figure 5-4) to the LTE network. If you choose Auto connect, click on Submit to save your selection. If you choose Manual connect, go to step 2.

20

Figure 5-4: LTE Settings

2. To manually connect the UE to the LTE network, choose Manual connect and click on PLMN for Public Land Mobile Network to scan all available networks and to select a specific LTE network to connect to. Select Connect to connect the network. Use the Disconnect button to disconnect from the selected network.

5.4 Configure Scan Mode

The Scan Mode setting determines which frequencies the UE’s routine scan of available frequencies will cover. Scanning is a process of tuning to a specific frequency and measuring the simplest signal quality [e.g., Received Signal Strength Indication (RSSI)]. As part of the cell selection and reselection process, the UE performs the scan first and then selects a small number of candidate cells to go through the next step of measuring and evaluating signals to select the best eNodeB (eNB) to serve it.

Go to Network > Scan Mode, and select either FullBand, PCI Lock, or Band/Frequency Preferred, as shown in Figure 5-5. The options are explained beneath the figure. Click on Submit to save the configuration.

Figure 5-5: Scan Mode

21

• FullBand – The UE will routinely scan all channels in the band. The band is dependent on the model of UE being used. Click on Submit after selecting this option.

• PCI Lock – Allows you to select the specific E-UTRA Absolute Radio Frequency Channel Number (EARFCN) and Physical Cell Identifier (PCI). After selecting PCI Lock, click on Submit. This will open the PCI Lock Settings window (Figure 5-6). After entering the information, click on Add to save the list. You can add more than one PCI Lock list. The UE will scan the list for eNBs with the PCI and EARFCN combination before locking on to one of them.

• Band/Frequency Preferred – You can specify which band(s) the UE will scan. After selecting Band/Frequency Preferred, click on Submit. This will open a settings window (Figure 5-7). Select the band by checking the check box next to it, and click on Add List. The window will display the EARFCN field. Select the desired EARFCN from the drop-down list, and then click on Add to add the list.

Figure 5-6: PCI Lock Settings

22

Figure 5-7: Band/Frequency Preferred Settings

5.5 Configure APN Management

Under Network > APN Management, you will configure up to 4 eNBs with which this UE may connect. APN is an acronym for Access Point Name. An access point, in this case, is another term for an eNB (base station). Refer to Figure 5-8 and Table 5-1 concerning the parameters. Click on Submit to save your data.

23

Figure 5-8: APN Management Settings

Table 5-1: APN Management Settings

Field Name Description

APN Selection

APN Number Select the APN number – 1, 2, 3, or 4

APN Settings

Enable Select the check box next to Enable to enable this APN

Name Required field: Enter a name for this APN

APN Name Enter the name of this APN, as defined in the eNB/base station configuration

Authentication Type Select the type of authentication required for this eNB/base station:

• None – the eNB/base station is not required to authenticate itself to the UE/CPE

• PAP – stands for Password Authentication Protocol, where the eNB/base station will authenticate itself to the UE/CPE using a static user name and password

24

• CHAP – stands for Challenge-Handshake Authentication Protocol, where the base station will authenticate itself to the UE/CPE through an authenticating entity

PDN Type Select the type of Packet Data Network (PDN) the eNB/base station can use when communicating with this UE/CPE: IPv4, IPv6, or IPv4v6

MTU Required field: Enter the Maximum Transmit Unit (MTU), which is the size of the largest network layer protocol data unit (PDU) that the eNB/base station can communicate in a single transaction. The range is 576 to 1500 bytes.

Manage Interface To enable a management interface to this eNB/base station, select the check box next to Enable.

Default Gateway To enable a default gateway to this eNB/base station, select the check box next to Enable.

25

Appendix A: Atom OD04/06-14 Technical Specifications

Basic Specifications

Item Description

LTE Standard Atom OD04-14: 3GPP Release 9, CAT4 Atom OD06-14: 3GPP Release 10, CAT 6/7

Ethernet LAN Port One RJ-45 port auto-sensing, auto-MDX, PoE:

• Atom OD04-14: 10/100 Mbps • Atom OD06-14: 10/100/1000 Mbps

LED Indicators MIU/LTE/SIM/LAN/PWR/LTE SIGNAL USIM 1.8V/3V 2FF

Restore Button Tactile button. Press button for at least 10 seconds to restore the UE to factory settings.

Power Supply Input: Universal range 100V to 240V AC Output: PoE (24VDC, 0.5A)

Dimensions (HxWxD) 9.5 x 6 x 2 inches 241 x 154 x 50 millimeters

Weight 2 lbs / 900 g

RF Specifications

Item Description

LTE Mode Atom OD04-14: FDD/TDD Atom OD06-14: TDD

Channel Bandwidth 5 / 10 / 15 / 20 MHz MAX Output Power 23 ± 2 dBm / TX antenna

TXRX

Atom OD04-14: 1T2R Atom OD06-14:

• 1T2R / 1T4R • 2T2R / 2T4R (uplink enhanced

Frequency Bands FDD Bands 7/38 (Atom OD04-14 only) TDD Bands 40/41 TDD Bands 42/43/48

Peak Rate FDD: DL 100 Mbps, UL 50 Mbps TDD (Atom OD04-14): DL 100 Mbps, UL 10 Mbps (2:7) TDD (Atom OD06-14): DL 220 Mbps, UL 15 Mbps (2:7)

Antenna Gain Atom OD04-14:

26

11 dBi @ 2.x GHz, 2 ports 14 dBi @ 3.x GHz, 2 ports

Atom OD06-14: 11 dBi @ 2.x GHz, 2 ports 11 dBi @ 3.x GHz, 4 ports 14 dBi @ 3.x GHz, 2 ports

Carrier Aggregation Atom OD06-14 only: 2CC CA

Modulation

Atom OD04-14: • UL: QPSK, 16QAM • DL: QPSK, 16QAM, 64QAM

Atom OD06-14: • UL: QPSK, 16QAM, 64QAM • DL: QPSK, 16QAM, 64QAM

Receive Sensitivity -94 dBm @ QPSK, 20 MHz, 25°C Antenna Type Internal directional Polarization ± 45° Antenna Efficiency > 70% Isolation ≤ -25 dB VSWR ≤ 2

Horizontal Beamwidth (3 dB)

Atom OD04-14: • 63 ± 3° @ 2.x GHz, 2 ports • 60 ± 3° @ 3.x GHz, 2 ports

Atom OD06-14: • 63 ± 3° @ 2.x GHz, 2 ports • 60 ± 3° @ 3.x GHz, 2 ports • 70 ± 5° @ 3.x GHz, 4 ports

Vertical Beamwidth (3 dB)

Atom OD04-14: • 35 ± 3° @ 2.x GHz, 2 ports • 25 ± 5° @ 3.x GHz, 2 ports

Atom OD06-14: • 35 ± 3° @ 2.x GHz, 2 ports • 25 ± 5° @ 3.x GHz, 2 ports • 30 ± 5° @ 3.x GHz, 4 ports

Atom OD06-14 notes:

Note 1: Different models support different frequencies, antennas, and Carrier Aggregation configurations.

Note 2: The current version supports only the 2-port antenna.

27

Wi-Fi Specifications

Item Description Standard IEEE 802.11b/g/n Channel Bandwidth 20/40 MHz Frequency 2.4 GHz TXRX 1T1R

Peak Rate 802.11b: 11 Mbps 802.11g: 54 Mbps 802.11n: 300 Mbps

Modulation DSSS/CCK, OFDM

Receive Sensitivity • -64 dBm @ 65 Mbps, typical for 802.11n • -65 dBm @ 54 Mbps, typical for 802.11g • -76 dBm @ 11 Mbps, typical for 802.11b

Max Output Power 10 ± 3 dBm Antenna Type Internal omni Antenna Gain 0 dBi

Software Specifications

Item Description Network Mode NAT / Bridge / Tunnel IP Protocol IPv4 / IPv6

USIM Universal Subscriber Identity Management: PIN management SIM lock

Network Connection Management Auto / Manual

LTE Scan Mode Full band scan, frequency lock

WLAN WPS MSSID isolation VLAN

VPN

Atom OD04-19.5: L2TP GRE PPTP L2 VxLAN Atom OD06-19.5: L2TP L2/L3 GRE L2/L3

NAT

Port forwarding Port trigger DMZ ALG

Firewall IP/MAC/URL filter

28

Item Description Access control Block port scanner / SYN flood SPI filter

Network Management TR069 SNMP

Diagnostics TCP dump Ping Trace route

Maintenance

Data and time setting Reboot Restore factory settings Restore / back up configuration files Firmware upgrade locally or OTA

System Logs Operating Run-time Filter / select / display / export

Statistics

LTE status / connection time /system up time Device status DHCP client list Wi-Fi station list Firewall status

Environmental Specifications

Item Description Operating Temperature -40°F to 131°F, -40℃ ~ 55℃ Storage Temperature -40°F to 158°F, -40℃ to 70℃ Operating Humidity 5% ~ 95% Ingress Protection Rating IP65

Global Part Numbers

Model Name Description

EG7010C-M1 Atom Outdoor 14 dBi UE, CAT 6/7, 2T2R, Bands 40/41 EG7010D-M11 Atom Outdoor 14 dBi UE, CAT 6/7, 2T2R, Bands 42/43/38 EG7035L-M1 OD04-14: Bands 40/41 EG7035L--M2 OD04-14: Bands 42/43 EG7035L-M10 OD04-14: Bands 7/38 EG7035L-M11 OD04-14: Bands 42/43/48 EG7011B-M2 OD04-14: Bands 42/43

29

Appendix B: Atom OD04/06-19.5 Technical Specifications

Basic Specifications

Item Description

LTE Standard Atom OD04-19.5: 3GPP Release 9, CAT4 Atom OD06-19.5: 3GPP Release 10, CAT 6/7

Ethernet LAN Port One RJ-45 port auto-sensing, auto-MDX, PoE: • Atom OD04-19.5: 10/100 Mbps • Atom OD06-19.5: 10/100/1000 Mbps

LED Indicators MIU/LTE/SIM/LAN/PWR/LTE SIGNAL USIM 1.8V/3V 2FF

Restore Button Tactile button. Press button for at least 10 seconds to restore the UE to factory settings.

Power Supply Input: Universal range 100V to 240V AC Output: PoE (24VDC, 0.5A)

Dimensions (HxWxD) 9.8 x 9.8 x 3.2 in 248 x 248 x 80 mm

Weight 4 lbs / 1800 g

RF Specifications

Item Description

LTE Mode Atom OD04-19.5: FDD/TDD Atom OD06-19.5: TDD

Channel Bandwidth 5 / 10 / 15 / 20 MHz MAX Output Power 23 ± 2 dBm

TXRX Atom OD04-19.5: 1T2R Atom OD06-19.5: 1T2R/1T4R, 2T2R/2T4R (uplink enhanced)

Frequency Bands

Atom OD04-19.5: Bands 7/38 Bands 40/41 Bands 42/43/48

Atom OD06-19.5: Bands 40/41/42/43/48 Customized

Peak Rate Atom OD04-19.5:

30

• FDD: DL 100 Mbps, UL 50 Mbps • TDD: DL 100 Mbps, UL 10 Mbps (2:7)

Atom OD06-19.5: • TDD: DL 220 Mbps, UL 15 Mbps (2:7)

Antenna Gain

OD04-19.5: • 14 dBi @ 2.x GHz, 2 ports • 19.5 dBi @ 3.x GHz, 2 ports

OD06-19.5: • 14 dBi @ 2.x GHz, 2 ports • 19.5 dBi @ 3.x GHz, 2 ports • 11 dBi @ 2.x GHz, 4 ports • 14 dBi @ 3.x GHz, 4 ports

Modulation

Atom OD04-19.5: • UL: QPSK, 16QAM • DL: QPSK, 16QAM, 64QAM

Atom OD06-19.5: • UL: QPSK, 16QAM, 64QAM • DL: QPSK, 16QAM, 64QAM

Receive Sensitivity -94 dBm @ QPSK, 20 MHz, 25°C Antenna Type Internal directional Polarization ± 45° Antenna Efficiency > 70% Isolation ≤-20 dB VSWR ≤2.5

Horizontal Beamwidth (3 dB)

OD04-19.5: • 35 ± 5° @ 2.x GHz, 2 ports • 25 ± 5° @ 3.x GHz, 2 ports

OD06-19.5: • 35 ± 5° @ 2.x GHz, 2 ports • 25 ± 5° @ 3.x GHz, 2 ports • 60 ± 5° @ 2.x GHz, 4 ports • 25 ± 5° @ 3.x GHz, 4 ports

Vertical Beamwidth (3 dB)

OD04-19.5: • 35 ± 5° @ 2.x GHz, 2 ports • 25 ± 5° @ 3.x GHz, 2 ports

OD06-19.5: • 35 ± 5° @ 2.x GHz, 2 ports • 25 ± 5° @ 3.x GHz, 2 ports • 35 ± 5° @ 2.x GHz, 4 ports • 25 ± 5° @ 3.x GHz, 4 ports

31

Wi-Fi Specifications

Item Description Standard IEEE 802.11b/g/n Channel Bandwidth 20/40 MHz Frequency 2.4 GHz TXRX 1T1R

Peak Rate 802.11b: 11 Mbps 802.11g: 54 Mbps 802.11n: 300 Mbps

Modulation DSSS/CCK, OFDM

Receive Sensitivity • -64 dBm @ 65 Mbps, typical for 802.11n • -65 dBm @ 54 Mbps, typical for 802.11g • -76 dBm @ 11 Mbps, typical for 802.11b

Max Output Power 10 ± 3 dBm Antenna Type Internal omni Antenna Gain 0 dBi

Software Specifications

Item Description Network Mode NAT / Bridge / Tunnel IP Protocol IPv4 / IPv6

USIM Universal Subscriber Identity Management: PIN management SIM lock

Network Connection Management Auto / Manual

LTE Scan Mode Full band scan, frequency lock

WLAN WPS MSSID isolation VLAN

VPN

Atom OD04-19.5: L2TP GRE PPTP L2 VxLAN Atom OD06-19.5: L2TP L2/L3 GRE L2/L3

NAT

Port forwarding Port trigger DMZ ALG

Firewall IP/MAC/URL filter Access control Block port scanner / SYN flood

32

Item Description SPI filter

Network Management TR069 TR104 (Atom OD06-19.5 only) SNMP

Diagnostics TCP dump Ping Trace route

Maintenance

Data and time setting Reboot Restore factory settings Restore / back up configuration files Firmware upgrade locally or OTA

System Logs Operating Run-time Filter / select / display / export

Statistics

Atom OD04-19.5: LAN link status Transmit/receive traffic Run time Atom OD06-19.5: LTE status / connection time /system up time Device status DHCP client list Wi-Fi station list Firewall status

Environmental Specifications

Item Description Operating Temperature -40°F to 131°F, -40℃ to 55℃ Storage Temperature -40°F to 158°F, -40℃ to 70℃ Operating Humidity 5% to 95% Ingress Protection Rating IP67

Global Part Numbers

Model Name Description

EG7010A-M11 Atom OD06-19.5 dBi, 3.5 GHz User Equipment EG7035E-M1 Atom OD04-19.5 dBi UE: Bands 40/41 EG7035E-M2 Atom OD04-19.5 dBi UE: Bands 42/43 EG7035E-M10 Atom OD04-19.5 dBi UE: Bands 7/38 EG7035E-M11 Atom OD04-19.5 dBi UE: Bands 42/43/48

33

Appendix C: CE Statement Baicells Technologies Co., Ltd. hereby declares that this LTE and Wi-Fi Wireless Terminal is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

1. The plug is considered a disconnect device of the adaptor.

2. The device complies with RF specifications when the device is used at 16 inches (40 cm) from your body.

34

Appendix D: FAQs If you have questions, please check the list of frequently asked questions (FAQs) on the Baicells support website or the Facebook support forum.

• Baicells support website - https://na.Baicells.com/support/

• Baicells support forum on Facebook - https://www.facebook.com/groups/Baicellsoperatorsupportgroup/