ATMATM PETE 689 UBD ATMATM ATMATMATMATM Lesson 9 Gasified Liquid Hydraulics Read: UDM Chapter 2.7...

ATMPETE 689 UBDATM

ATM ATM

Lesson 9

Gasified Liquid Hydraulics

Read: UDM Chapter 2.7

pages 2.131-2.179

Harold Vance Department of Petroleum Engineering

ATMPETE 689 UBDATM

ATM ATM

Gasified Liquid Hydraulics

• Reynolds Number

• Multi-phase flow

• Pressure prediction– HSP– Circulating pressure– Bit pressure drop

• Hole Cleaning


ATMPETE 689 UBDATM

ATM ATM

Reynolds Number

• In practice the flow of gasified liquid is almost always turbulent (Reynolds number > 4000)

• Example water flowing up an 8 1/2” hole with 5” drillpipe.

• AV of 7 ft/min would be turbulent

• AV’s > 100 ft/min are common


ATMPETE 689 UBDATM

ATM ATM

Reynolds Number

• Equation 2.58


ATMPETE 689 UBDATM

ATM ATM

Reynolds Number

• The consequenses of turbulance in the annulus is that the rheology of gasified fluids has little effect on the annular pressure profile.

• This is at least true with un-viscosified base fluid.


ATMPETE 689 UBDATM

ATM ATM

Multi-phase flow

• At least three phases are present in the wellbore– Liquid, gas, and solids

• Liquids could be:– Mud– Oil– Water


ATMPETE 689 UBDATM

ATM ATM

Flow Regimes


ATMPETE 689 UBDATM

ATM ATM

Pressure prediction

• HSP• Annular Friction• Bit pressure drop

– Mud– Gasified mud

• Drillstring pressure drop– Mud– Gasified mud


ATMPETE 689 UBDATM

ATM ATM

HSP

1

2

0144P

PhVdP


ATMPETE 689 UBDATM

ATM ATM

HSP


ATMPETE 689 UBDATM

ATM ATM

Gas Volume


ATMPETE 689 UBDATM

ATM ATM

Friction forces


ATMPETE 689 UBDATM

ATM ATM

Fanning Friction Factor


ATMPETE 689 UBDATM

ATM ATM


ATMPETE 689 UBDATM

ATM ATM

Reduced Reynolds Number


ATMPETE 689 UBDATM

ATM ATM


ATMPETE 689 UBDATM

ATM ATM

Gas volume

• This correlation and equation 2.66 were used to compute the required air injection rate to give a BHP of 2497 psi at 6000’ in an 8 1/2” X 4 1/2” annulus at 350 gpm.

• Required 14.9 scf/bbl


ATMPETE 689 UBDATM

ATM ATM

Gas volume

• Equation 2.63 was used to calculate the volume of air to give the same BHP static.

• Required 13.4 scf/bbl.

• Poettmann and Bergman concluded that the difference is insignificant and a reasonable calculation of air rate for the desired BHP could be done assuming a static fluid column.


ATMPETE 689 UBDATM

ATM ATM


ATMPETE 689 UBDATM

ATM ATM

Bit pressure drop

• Mud

• Gasified Mud


ATMPETE 689 UBDATM

ATM ATM

Bit pressure drop - Mud

• Red book


ATMPETE 689 UBDATM

ATM ATM

Bit pressure drop - Gasified Mud

• This relationship neglects any energy loss through the nozzles due to frictional effects and any change in potential energy.


ATMPETE 689 UBDATM

ATM ATM

Bit pressure drop - Gasified Mud

• Substituting equation 2.44 for the density of a lightened fluid this becomes


ATMPETE 689 UBDATM

ATM ATM


ATMPETE 689 UBDATM

ATM ATM

Fig. 2.41


ATMPETE 689 UBDATM

ATM ATM

Hole Cleaning

• Settling velocity

• Critical velocity

• Settling Velocity

• Cuttings Transport ratio


ATMPETE 689 UBDATM

ATM ATM

Settling velocity


ATMPETE 689 UBDATM

ATM ATM

Critical velocity

• Guo assumed that the cuttings concentration in the annulus should not exceed some critical value if hole cleaning problems were to be avoided.

• vc = ROP/60Cc

• vc = critical velocity, ft/min

• ROP = Rate of penetration, ft/hr

• Cc = Cuttings concentration, fraction


ATMPETE 689 UBDATM

ATM ATM

Critical velocity

• Taking the critical concentration as 4%, cuttings would need to travel uphole with a velocity 25 times greater than the penetration rate.

• For a penetration rate of 30 ft/hour, this corresponds to a velocity of 12.5 ft/min.


ATMPETE 689 UBDATM

ATM ATM


ATMPETE 689 UBDATM

ATM ATM

Settling Velocity

• With a large annulus, the AV may not be such that turbulent flow can be achieved.

• We would then need to alter the viscosity of the fluid.


ATMPETE 689 UBDATM

ATM ATM

Settling Velocity

• For a 0.25” cutting with a density of 21 ppg falling through a fluid of density of 5 ppg.

• Maximum AV = 15 ft/min.

• Settling velocity would have to be restricted to 17.4 ft/min at a penetration rate of 30 ft/hr.

• This would require an effective viscosity of 160 cP.


ATMPETE 689 UBDATM

ATM ATM

Cuttings Transport Ratio


ATMPETE 689 UBDATM

ATM ATM

Cuttings Transport Ratio• The velocity of the system is normally the mean

velocity in the annulus determined by dividing the total flow rate of the various phases of the fluid by the cross-sectional area of the annulus.


ATMPETE 689 UBDATM

ATM ATM

Cuttings Transport Ratio

• The CTR should be calculated throughout the annulus to ensure that adequate hole cleaning takes place at all points and that the cuttings are not packing off in the hole somewhere.

• A CTR of 1.0 implies perfect hole cleaning.

• If CTR>0 cuttings are moving upward.

• CTR should be >0.55


ATMPETE 689 UBDATM

ATM ATM

Example


ATMPETE 689 UBDATM

ATM ATM

ATMATM PETE 689 UBD ATMATM ATMATMATMATM Lesson 9 Gasified Liquid Hydraulics Read: UDM Chapter 2.7...

Documents

Transcript of ATMATM PETE 689 UBD ATMATM ATMATMATMATM Lesson 9 Gasified Liquid Hydraulics Read: UDM Chapter 2.7...