GENERIC PROJECT DOCUMENT ATDP_ES_000212

TYPICAL RATES SCHEDULEISSUE 0

COPYRIGHT

Earthworks

Earthworks (Pipe Trenches)

Roads

Piling Auger Piles

Civil Works

Civil Works

Trackwork Trackwork

Structural Steel

Platework

Mechanical

Pipework

Pipework

Electrical

ATDP_ES_00021200 DRAFT 4-May-06 Page 1 of 1

Demolitions Site Clearance Excavations Fill Sundries

Site Clearance Excavations Fill Pipeline Valve Chambers Drainage

"All in" Rates Culverts Earthworks Surface Treatment Sundries

Concrete Formwork Rebar Joints Grouting

Miscell Metal Sundries

Steelwork Flooring Handrailing Cladding

Mild steel Stainless steel Liners Sundries

Valves Equipment

HDPE Piping SABS 62 R/Lined 719 GrB R/Lined SABS 62 Copon 719 GrB Copon SABS 62

719Gr B Stainless Steel S/Socketted Schedule 40 (0 to 150) Schedule 40 >200 "All in rates"

LV Cables MV Cables 600/1000V Cable Earthing Racking Sundries

document.xls Revision 0 Approved : October 31, 2001

SCHEDULE OF RATES

Code Item Description Unit Rate

AA EARTHWORKS

AA100 10 DemolitionsAA200 20 Break up and removeAA210 30 100mm Thick unreinforced concrete surface beds, paving m3 380AA220 40 100mm Thick mesh reinforced concrete surface beds, pavm3 410AA225 Sawcut surface bed 6mm x 40mm deep m 12AA230 50 75mm Thick brick paving with mortar joints m2 50AA240 60 150mmx250mm High reinforced concrete kerbs m 15AA300 Taking down and removeAA310 Diamond mesh fence 2.5m high complete with steel postsm 25AA320 Diamond mesh security fence with 45 degree razor wire overhang 2.8m

high overall complete with steel posts and droppers m 40AA330 One brick boundary wall complete with foundations 2m hi m2 95AA340 Half brick boundary wall complete with foundations 1.8m m2 85AA400 Demolishing and removingAA410 Single storey building with pitched roof 10 x 10 m on plan and 3m high

at eaves comprising concrete surface bed, 220mm thick external walls110mm internal walls and chromadek roof covering on timno

AA420 Mild steel framed shed including all IBR roof and side sheeting 10 X 10mon plan and 3m high comprising reinforced concrete surface bed, 110mm internal walls, column bases and foundations and no

AA500 Site ClearanceAA510 Clear and grub site of all vegetation, shrubs, rubbish etc ha 4000AA520 Remove topsoil to nominal depth of 150mm stockpile and m3 12AA530 Rip to 150mm depth and recompact in-situ material to m3 8.5

AA600 Bulk Excavation, Filling, etcAA610 Excavate in all materials and dispose m3 18.5AA620 Excavate in all materials and use as backfill as ordered m3 25AA630 Extra over for hard rock excavation m3 120AA640 Overhaul (assume 2km free haul) m3/k 2AA650 Opening and closing of designated borrow pits sum 10000AA660 Dealing with overburden m3 18AA700 Restricted Excavation -assume all material to be disposedAA710 Excavate in all materials for foundations m3 28AA720 Excavate in all materials for bases m3 30AA730 Excavate in all materials for sumps m3 30AA740 Excavate in all materials for surface bed and thickenings m3 28AA750 Excavate in all materials for V-drains m3 25AA760 Excavate in all materials for trapezoidal drains m3 25AA770 Excavate in all materials for catch pits m3 30

AA800 Importing of MaterialsAA810 From designated borrow pitAA820 Fill making up levels in 150mm layers compacted to minimum 90% Mod

AASHTO density m3 26AA830 Ditto, to 93% Mod AASHTO density m3 28AA840 From commercial sourcesAA850 26mm Thick crushed stone layer uncompacted m3 150

AA900 SundriesAA910 Extra over excavation in all materials for working space over 0 and up to

2m total depth m2 28AA920 Ditto, exceeding 2m but not exceeding 4m total depth m2 32AA930 Polyethelene sheeting laid under surface bed m2 4.5

AA940 In-situ compaction 150mm deep to minimum 93% Mod.A m3 16.5

RETURN TO MENU

RETURN TO MENU

RETURN TO MENU

RETURN TO MENU

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

SCHEDULE OF RATES

CodeItem Description Unit Rate

AB EARTHWORKS (PIPE TRENCHES)

AB100 Site ClearanceAB110 Clear and grub site of all vegetation, shrubs, rubbish etc ha 4000AB120 Remove topsoil to nominal depth of 150mm stockpile and maintain m3 12

AB200 Excavate in all materials for trenches, backfill, compact to minumum90% Mod AASHTO density and dispose of surplus material for pipesup to 225mm diameter for depths:

AB210 Pipe trenches exceeding 0,0m but not exceeding 1,0m deep m 45AB220 Ditto, exceeding 1,0m but not exceeding 2,0m deep m 54AB230 Ditto, exceeding 2,0m but not exceeding 3,0m deep m 60AB230 Ditto, exceeding 3,0m but not exceeding 4,0m deep m 68AB240 Extra over all excavations for excavation in intermediate material m3 85AB250 Extra over all excavations for excavation in hard rock material m3 100

AB300 Importing of Bedding MaterialsAB310 From designated borrow pitAB320 Selected granular bedding material compacted to 90% Mod AASHTO

density m3 18AB330 Selected fill material compacted to 90% Mod AASHTO density m3 18

AB400 Medium Pressure PipelinesSupply, handle, lay, joint bed in selected material, test and disinfect pipes

AB405 110mm Diameter Upvc pressure pipes class 6 with rubber ring joints m 95AB410 200mm Diameter, ditto m 125AB415 Extra over for 110mm diameter 45 degree bend complete with all necessary

couplings including cutting pipes to length where required no 250AB420 Ditto, for 200mm diameter 45 degree bend, ditto no 350AB425 Ditto, for 110mm diameter 90 degree bend, ditto no 250AB430 Ditto, for 200mm diameter 90 degree bend, ditto no 350AB435 200 X 50mm Diameter reducing tee noAB450 200mm Diameter saddle noAB500 Valves, Chambers, Piping etcAB510 Chamber with 230mm thick brick walls pointed internally with flush joints

externally for and including bagwash to external walls, with 200mm thickconcrete 20Mpa/19mm base slab including mesh reinforcement type 311to base slab, excavations in all materials, sleeves through wall for 200mm diameter pipes and 4,5mm thick chequer plate cover on two sections,including framing, hinges, lugs, packs, hasp, staple, padlock, lifting handleand corrosion protection, size 1000 x1000 x 1000mm deep no 5000

AB520 20Mpa to anchor blocks m3 480AB530 Rough formwork to anchor blocks m2 75AB600 Stormwater DrainageAB610 Supply, lay, bed and joint in trench class 75D precast concrete pipes with

IJ joints:600mm Diameter m 380750mm Diameter m 570Head walls for 600mm pipe culvert no 2000Head walls for 750mm pipe culvert no 2400

RETURN TO MENU

RETURN TO MENU

RETURN TO MENU

RETURN TO MENU

RETURN TO MENU

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

SCHEDULE OF RATES

CodeItem Description Unit Rate

RoadsTypical "all in" rates for roads (no major earthworks)8m Wide road with 1.3m shoulder with 30mm Premix m 630/m6m Wide road with 1.0m shoulder with chip and spray m 510/m6m Wide road with 1.0m shoulder with (MC 30 Bitumen - ratem 570/m6m Wide road with 1.3m shoulder with 30mm Premix m 500/m6m Wide gravel road (no major earthworks) m 250/m4m Wide gravel road (no major earthworks) m 160/m6m Wide gravel road ( major earthworks) m 510/mCulverts3600x3000mm Hi class C culvert m 8960/m3600x1500mm Hi class C culvert m 6156/m3000x2400mm Hi class C culvert m 8200/m3000x1800mm Hi class C culvert m 6156/m2400x1200mm Hi class C culvert m 3300/m2400x900mm Hi class C culvert m 2500/m2100x2100mm Hi class C culvert m 5900/m2100x1500mm Hi class C culvert m 3591/m1500x900mm Hi class C culvert m 1850/m

AC100 Site ClearanceAC110 Clear and grub site of all vegetation, shrubs, rubbish etc ha 4000AC120 Remove topsoil to nominal depth of 150mm stockpile and mm3 12AC200 Treatment of Road-bedAC210 Road-bed preparation by thoroughly wetting in-situ material and drying

to optimum moisture content and compaction of material with six passesof a 12 ton vibratory or impact roller m2 6

AC230 Road-bed preparation and compaction of materials to 93% Mod AASHTOdensity to a depth of 150mm m3 16

AC300 EarthworksAC310 Borrow to fill with material from designated borrow pit in 150mm layers

compacted to 90% Mod AASHTO density m3 20Ditto, in fill behind kerbs m3 50

AC320 Construct selected subgrade layer with material from designated borrowpit in 150mm layers compacted to 93% Mod AASHTO densim3 25

AC330 Cut to spoil in all materials m3 10AC340 Overhaul (within 2km radius) m3/k 2AC400 SubbaseAC410 Construct subbase with material from designated borrow pit in 150mm layers

compacted to 95% Mod AASHTO density m3 20Process subbase material byb) Stabilisation m3 15Stabilising Agenta) Portland cement ton 600

AC500 BaseAC510 Construct base with material from designated borrow pit in 150mm layers

compacted to 95% Mod AASHTO density m3 20AC520 Construct base with material from commercial sources in 150mm layers

of crusher run to 88% Mod AASHTO density m3 200AC600 Surface Treatment AC610 Prime coat using MC 30 cut back bitumen at a rate of 0,8 li m2 3AC620 Prime coat using RTH 3/12 P at a rate of 0,75 litres/m2 m2 2.5AC630 Bituminous surface treatment with aggregate and slurry seal using 19mm

aggregate at 0,013m3/m2 with cationic emulsion binder at 0,7 litre/m2 one

RETURN TO MENU

RETURN TO MENU

RETURN TO MENU

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

slurry seal application consisting of 60% stable grade emulsion at 260 litrescement at 0,01m3, water at 235 litres, spread on site at ra m2 20

AC640 Double surface treatment using tack coat of 150/200 penetration grade bitumen applied at a rate of 1,2 litres/m2 m2

AC650 19mm Aggregate at 0,014m3/m2 as first application with 150/200 penetrationgrade bitumen emulsion applied at a rate of 0,87 litres/m2 m2 18

AC660 9,5mm Aggregate at 0,006m3/m2 as second application with 150/200penetration grade bitumen emulsion applied at a rate of 1,2 m2

AC670 Fog spray cationic emulsion 65% applied at a rate of 0,6lit m2AC680 Pre-coated chips nominal size 19mm m3AC700 KerbingAC710 Non-mountable concrete kerbing laid straight including earthworks, grouting

benching and haunching in 15Mpa/25mm concrete m 90AC720 Curved mountable kerbing of radius not exceeding 1m ditto m 92AC730 Curved mountable kerbing of radius exceeding 4m and exc m 98AC800 Statutory Road SignsAC810 Approved road signs with and including 100mm diameter treated timber

supporting post, excavation and setting post in concrete 25Mpa/19mmAC 820 Stop sign no 450AC830 Yield sign no 450AC840 Directional sign no 450AC850 Road Markings (applied at a rate of 0,42litres/m2)AC860 Road marking lines m 3.5AC870 Road marking characters and symbols noAC880 Setting out and premarking lines m 4.5AC890 Setting out and premarking characters and symbols m2AC900 Ancillary RoadworksAC910 Armco galvanised guard rails on treated timber posts complete with all

earthworks, concrete etc m 150Extra over for horizontally curved guard rails, factory bent to a radius of lessthan 150m m 40

AC920 Armco galvanised end wings no 140Terminal section no 2000Reflector plates no 20

RETURN TO MENU

RETURN TO MENU

SCHEDULE OF RATES

AD PILING

CodeItem Description Unit Rate

AD100 Concrete PilingAD110 Establish on site for piping sumAD120 Move equipment and set up at each pile position noAD130 Auger holes for pipes of 1200mm diameter through material in the following

successive depth ranges over 0,00m and up to 10,0m mAD140 Ditto, over 10,0m and up to 20m mAD150 Extra over, irrespective of depth, for augering holes through obstructions

consisting of boulders mAD160 Ditto, in rock formation mAD170 Install and remove temporary casing in auger holes for pil mAD175 Install permanent pile casing for piles of 1200mm diameter mAD180 Concrete 25 Mpa in cast in situ piles m3AD185 Cut pile heads 1200mm diameter pipe noAD200 TestingAD210 Establish on site for the load testing of piles sumAD300 Compression Load Test on PilesAD310 1200mm Diameter to 5000Kpa sum

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

SCHEDULE OF RATES

Code Item Description Unit Rate

CIVILWORKSAE100 Mass Concrete AE110 Concrete 10Mpa/19mm blinding layer 50mm minumum thic m2 26AE200 Structural Concrete (25Mpa)AE205 Strip footings m3 500AE210 Bases m3 510AE215 Pump bases m3 500AE220 Sump walls and base m3 510AE225 Surface bed and thickenings m3 510AE230 Plinths m3 500AE235 Kerbs m3 510AE240 Columns m3 500AE245 Beams m3 520AE250 Walls m3 510AE255 Suspended slabs m3 520AE265 Culvert headwall and footing m3 500AE300 Unformed surface fininshesAE310 Wood float finish m2 5AE320 Steel float finish m2 6.5AE400 FormworkAE405 Rough formwork to bases m2 90AE410 Rough formwork to sump m2 90AE415 Rough formwork to strip footings m2 90AE420 Smooth formwork to bases m2 110AE425 Smooth formwork to walls of sump m2 115AE430 Smooth formwork to surface bed and thickenings m2 110AE435 Smooth formwork to columns m2 115AE440 Smooth formwork to kerbs m2 115AE445 Smooth formwork to walls m2 115AE450 Smooth formwork to soffit of suspended slab m2 200AE450 QC-decking 1,2mm thick to soffits of suspended slabs m2 220AE455 Flashings to sides of suspended slabs exceeding 150mm m 400AE460 To narrow widths not exceeding 150mm high m 25AE465 To narrow widths exceeding 150mm not exceeding 300mm m 36AE470 Box out formwork to form 80mm diameter x 200mm deep h.dno 15AE500 ReinforcementAE510 25mm Diameter mild steel bars t 3600AE515 Extra over for 8mm bars t 600AE520 Extra over for 10mm bars t 400AE530 Extra over for 12mm bars t 350AE540 Extra over for 16mm bars t 200AE550 25mm Diameter high tensile steel bars t 3800AE560 Extra over for 8mm bars t 450AE570 Extra over for 10mm bars t 300AE580 Extra over for 12mm bars t 250AE590 Extra over for 16mm bars t 180AE591 Welded mesh reference 245 m2 35AE592 Welded mesh reference 311 m2 30AE600 JointsAE610 Formwork to expansion joint exceeding 0 n/e 150mm high m 25AE620 12mm Thick flexcell or impregnated fibreboard joint filler m 32AE630 Rake out 12mm thick joint filler 12mm deep and fill with ploysulphide

RETURN TO MENU

RETURN TO MENU

RETURN TO MENU

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

sealant, including bond m 22AE640 Formwork to joggle joint exceeding 0 n/e 150mm high m 40AE650 Box out to formwork to form 20x20 mm deep groove m 12AE660 Polysulphide sealant 12mm deep to 20 x 20mm groove, including

polyethylene back-up m 30AE670 Form construction joint through 200mm thick ground slab mAE680 Form construction joint through 300mm thick ground slab mAE700 GroutingAE710 Non-shrink, non-metallic grouting under base plates dm3 8AE720 Non-shrink, non-metallic grouting to h.d bolt pockets dm3 8AE730 Cement/Sand grouting dm3 3.5

AE800 H.D Bolts and Miscellaneous MetalworkAE810 Provide and install 12mm diameter mild steel h.d bolts with kg 18.5AE820 Ditto, 20mm diameter kg 16.5AE830 Ditto, 30mm diameter kg 15AE840 Provide and install 50x50x6mm galvanised mild steel kerb angle with flat

and lugs welded on kg 14.5AE850 Ditto, 16mm thick mild steel plate with lugs welded on kg 14.5AE900 Sundries

DowelsAE910 Drill 30mm diameter x 300 mm deep hole vertically in concr no 25AE915 Provide and install 20mm diameter x 1850mm long high tensno 28AE920 Grout up dowels with Epidermix 395 or other approved groudm3 80

ManholesAE930 Manhole overall size 1500 x 1500 x 300mm deep consisting of 100mm thick

concrete 30Mpa/19mm base and cover slabs reinforced with high tensilemesh type 311, one brick thick walls plastered internally and cast ironmanhole cover type 4A no 3800Fencing

AE940 Provide and install 2.0m high fence infilled with galvanised diamond meshand with 5No rows of 4mm galvanised straining wire and Y-section droppers2m long at maximum 2,5m centres m 160

AE945 Extra over for 150mm diameter gate posts, including setting post and strut in concrete base no 400

AE950 Extra over for 150mm diameter corner posts with two struts no 500AE955 Galvanised mild steel single leaf gate consisting of 42mm nominal bore x

4mm thick welded frame infill with galvanised diamond mesh, including pivots,bolts, bolting to post etc. Size 700x1940mm high no 850

AE960 Ditto, two leaf with 2 No braces. Each leaf size 1335 x 19 no 1800

AE1000 Provisional SumsAE1100 Weighbridge

Provide the sum of one hundred and fifty thousand rand (R150 000.00)for the building of a weighbridge. sum 150 000

AE1200 Sub-StationsProvide the sum of one hundred thousand rand (R100 000.00) for the building of a sub-station sum 100 000

AE1300 MCC RoomProvide the sum of eighty thousand rand (R80 000.00) for the building of a MCC Room sum 80 000

AE1400 Oil StoreProvide the sum of ninety thousand rand (R90 000.00) for the building of an Oil Store sum 90 000

AE1500 Gas StoreProvide the sum of fifty thousand rand (R50 000.00) for the building of a Gas Store sum 50 000

AE1600 Paint Store

RETURN TO MENU

RETURN TO MENU

RETURN TO MENU

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

Provide the sum of fifty thousand (R50 000.00) for the building of a Paint Store sum 50 000"All in" Rates

AE1700 Survey Beacons (1m3) no 2000Pollution Control Dam -civils only m2 150/m21500T Concrete Silo including throat liners m3 1950/m34000T Concrete Silo including throat liners m3 1500/m3Concrete Potable Water Tank m3 1350/m3

RETURN TO MENU

SCHEDULE OF RATES

CodeItem Description Unit Rate

TRACKWORKAF100 BallastAF110 Provide and distribute ballast, 53mm nominal size 1050m3/km3AF200 Lay or install plain trackAF210 Lay plain track in 36m lengths mAF215 Lift, pack and box plain track mAF220 Extra over for laying in curves not exceeding 300mm radiusmAF225 Lay turnouts noAF230 Lay stopblocks noAF235 Lift, pack and box turnouts noAF240 Lift, pack and box stopblocks noAF245 Cut rail using rail saw or disc cutter noAF250 Supply and transport to site Grinaker or other approved precast reinforced

sleepers complete with pandrol fastenings, fittings and insu noAF255 Supply , delivery to site and offloading of fishplate joints complete, heavy duty

design noAF300 SundriesAF310 Supply, deliver and install Clearance Marker noAF320 Ditto, Whistle board, including post, excavation, setting in c no

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

SCHEDULE OF RATESSUPPLYTRANSPORT ERECT TOTAL

CodeItem Description Unit Rate Rate Rate Rate

STRUCTURAL STEELWORK

AG100 Supply, Fabricate, Transport to Site and ErectionAG101 Purlins and girts t 7582 173.81 1540.92 9296.73AG102 Single section columns t 9458 173.81 963.08 10594.89AG103 Platework columns t 10036 173.81 963.08 11172.89AG104 Lattice columns t 10901 173.81 963.08 12037.89AG105 Composite columns t 10036 173.81 963.08 11172.89AG106 Single section beams t 9458 173.81 1091.49 10723.3AG107 Composite beams t 9458 173.81 1091.49 10723.3AG108 Single section crane beams t 9458 173.81 1091.49 10723.3AG109 Composite crane beams t 11190 173.81 1091.49 12455.3AG110 Crawl beams t 9458 173.81 1091.49 10723.3AG111 Plate girders t 7135 173.81 1091.49 8400.3AG112 Lattice girders t 8754 173.81 1091.49 10019.3AG113 Rafters t 9747 173.81 1155.69 11076.5AG114 False rafters t 10036 173.81 1155.69 11365.5AG115 Single section bracing t 9204 173.81 1155.69 10533.5AG116 Star angle bracing t 9458 173.81 1155.69 10787.5AG117 Tubular bracing t 14090 173.81 1155.69 15419.5AG118 Door posts t 9105 173.81 963.08 10241.89AG119 Sag rods t 15519 173.81 2054.56 17747.37AG120 Sag angles t 13355 173.81 1540.92 15069.73AG121 Stairs, landings and walkways t 10296 173.81 1284.1 11753.91AG122 Crane rails t 8325 173.81 2054.56 10553.37AG123 Catladders t 19848 173.81 2054.56 22076.37AG124 Handrails, kneerails and stanchions - site fabricated t 0AG125 Gantries t 10826 173.81 1091.49 12091.3AG126 Trestles t 10826 173.81 898.87 11898.68AG127 Conveyor stringers t 11850 173.81 898.87 12922.68AG128 Conveyor legs t 7896 173.81 898.87 8968.68AG129 Conveyor head and tail frames t 12191 173.81 1091.49 13456.3AG130 Take up frames t 12191 173.81 898.87 13263.68AG131 Conveyor deck plates t 10980 173.81 1540.92 12694.73AG132 Conveyor skirt plates t 10826 173.81 1284.1 12283.91AG133 Platework in counterweights t 13146 173.81 77046 90365.81AG134 Motor sole plates t 0AG135 Framing to guards t 10826 173.81 963.08 11962.89AG136 Guard mesh m2 0AG137 Pig tails no 0 0AG138 Conveyor skirt rubber m 0AG139 Bolts - 4.6 t 8386 173.81 963.08 9522.89AG140 Bolts - 8.8 t 11151 173.81 963.08 12287.89AG200 Flooring 0

RETURN TO MENU

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

AG210 Mentis rectagrid RS40 or other approved hot dipped galvanised mild steel 0grating with 40x5mm bearer bars bolted to steelwork m2 495 4.67 489.79 989.46

AG220 Hot dipped galvanised stair tread 750mm long x 245mm wide with non slip 0nosing and side plates bolted to steelwork no 85.23 2.11 45.76 133.1

AG230 Hot dipped galvanised mild steel 130x8mm kickflat welded on m 90 0.93 81.31 172.24AG300 Handrailing 0AG310 34mm Diameter Mentis or equal approved hot dipped galvanised mild steel 0

tubular handrailing system secured to stanchions (elsewhere measured)m 23.96 1.41 9.79 35.16AG320 Extra over for standard 90 degree bend no 19.77 0.35 17.71 37.83AG330 Ditto, 45 degree bend no 20.05 0.35 17.71 38.11AG340 Ditto, 45 degree angle closure to end of handrailing no 30.13 0.35 17.71 48.19AG350 Ditto, 90 degree angle closure to end of handrailing no 28.45 0.35 17.71 46.51AG360 43mm External diameter tubular stanchion, 1025mm high c/w base plate 0

and welded or bolted to cast in plates including bolts no 59.31 2.64 71.83 133.78AG400 Cladding 0AG410 Supply, deliver and install complete IBR or similar approved profiled 0

galvanised metal sheeting, corrosion by Colomet C1S, including stainless 0steel fastenings and fixings 0

AG415 0.8mm Thick roof sheeting m2 72.29 incl. 72.29AG420 0.6mm Thick vertical cladding m2 55.08 incl. 55.08

Accessories 0AG425 Vertical corner trim 462mm girth m 24.56 incl. 24.56AG430 Ridge capping girth 600mm m 31.36 incl. 31.36AG435 Polyclosers m 4.14 incl. 4.14AG440 Door trim flashing girth 462mm m 24.56 incl. 24.56AG445 Bullnose profile to end of sheeting m 19.24 incl. 19.24AG450 Supply, deliver and install complete Stainless steel IBR Grade 430 sheeting 0

with colomet finish one side fixed to steelwork with 304mm stainless steel 0topspeed screws and bonded stainless steel washers 0

AG455 0.559mm Thick roof sheeting m2 120.65 120.65AG460 0.559mm Thick side sheeting m2 120.65 120.65

Accessories 0AG465 Vertical corner trim 462mm girth m 58.32 58.32AG470 Ridge capping girth 600mm m 83.5 83.5AG475 Polyclosers m 4.14 4.14AG480 Door trim flashing girth 462mm m 58.32 58.32

RETURN TO MENU

RETURN TO MENU

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

SCHEDULE OF RATES

Code Item Description Unit Supply Transport Erect Total

PLATEWORK

AH100 Platework to tanks, chutes, bins, hoppers etcAH105 Supply, Fabricate, Transport to Site and Erection of Mild Steel PlateAH110 Framing and support steelwork t 9458 173.81 963.08 10594.89AH115 6mm Thick platework t 13695 531.72 1540.9 15767.64AH120 Ditto, rolled to a circular profile tAH125 8mm Thick platework t 12630 531.72 1540.9 14702.64AH130 Ditto, rolled to a circular profile tAH135 10mm Thick platework t 11746 531.72 1540.9 13818.64AH140 Ditto, rolled to a circular profile tAH145 12mm Thick platework t 11746 831.72 1540.9 14118.64AH150 Ditto, rolled to a circular profile tAH155 Bolts - 4.6 t 8386 173.81 963.08 9522.89AH160 Bolts - 8.8 t 11151 173.81 963.08 12287.89AH200 Ditto, Stainless Steel SS316 PlateworkAH205 6mm Thick platework t 44285 531.72 1540.9 46357.64AH210 Ditto, rolled to a circular profile tAH215 8mm Thick platework t 44285 531.72 1540.9 46357.64AH220 Ditto, rolled to a circular profile tAH225 10mm Thick platework t 44285 531.72 1540.9 46357.64AH230 Ditto, rolled to a circular profile tAH235 12mm Thick platework t 44285 531.72 1540.9 46357.64AH240 Ditto, rolled to a circular profile tAH245 Bolts - 4.6 t 88060 173.81 963.08 89196.89AH250 Bolts - 8.8 t 88060 173.81 963.08 89196.89AH300 LinersAH310 MOH scale 9 hardness 94% alumina tiles, including preparing surfaces to

receive epoxy bonding material and filling joints and edgesAH315 12mm Thick ceramic tiles m2 1735 173.81 1908.81AH320 25mm Thick ceramic tiles m2 1950 173.81 2123.81AH330 VRN 500 wearing plate liners each not exceeding 35kg each to be fixed with

and including a minimum of 4No M16 countersunk nib headboltsAH335 12mm Thick VRN hardwearing plate liners t 16955 173.81 17128.81AH340 25mm Thick VRN hardwearing plate liners t 17190 173.81 17363.81AH350 6mm Thick natural soft rubber Grade A 40 Shore A hardness, with 18Mpa

tensile strength lining fixed to steel surfaces, including scarfing and preparingsurfaces

AH355 6mm Thick rubberlining m2 413.42 413.42AH360 12mm Thick rubberlining m2 495.23 495.23AH370 Ultra high molecular polyurethane 12mm thick Solidur B15 liner with and

including bolted fixings to plateworkAH375 Polyurethane liners m2 2650 173.81 2823.81AH400 SundriesAH405 50mm Nominal bore, 6mm wall thickness nozzle with and including 50mm

nominal bore flanged end no 253.93 173.81 50.97 478.71AH410 Ditto, 80mm Nominal bore, ditto no 307.31 173.81 54.99 536.11AH415 Ditto, 100mm Nominal bore, ditto no 371.99 173.81 92.23 638.03AH420 Ditto, 200mm Nominal bore, ditto no 585.05 173.81 105.16 864.02AH425 Ditto, 400mm Nominal bore, ditto no 1028.17 173.81 325.69 1527.67

document.xls Revision 0 Approved : October 31, 2001

SCHEDULE OF RATES

CodeItem Description Unit Rate

MECHANICAL INSTALLATIONAH Take delivery from stores, transport onto site, hoist into position, align

level and fix in position including cold commission

AH Free Issue Valve SupplyErection Only

AH 1 Gate ValvesAH 2 50mm diameter no 62AH 3 80mm diameter no 74AH 4 100mm diameter no 82AH 5 150mm diameter no 92AH 6 200mm diameter no 125AH 7 250mm diameter no 135AH 8 300mm diameter no 174AH 9 350mm diameter no 220AH 10 400mm diameter no 270AH 11 450mm diameter no 360AH 12 500mm diameter no 400AH 13 600mm diameter no 620AH 14 650mm diameter no 780AH 15 Butterfly ValvesAH 16 80mm diameter no 75AH 17 100mm diameter no 82AH 18 150mm diameter no 95AH 19 250mm diameter no 140AH 20 Diaphragm ValveAH 21 15mm diameter no 33AH 22 20mm diameter no 36AH 23 25mm diameter no 40AH 24 40mm diameter no 44AH 25 50mm diameter no 62AH 26 80mm diameter no 75AH 27 100mm diameter no 82AH 28 150mm diameter no 92AH 29 200mm diameter no 125AH 30 250mm diameter no 135AH 31 300mm diameter no 175AH 32 350mm diameter no 230AH 33 Check ValvesAH 34 20mm diameter no 36AH 35 50mm diameter no 62AH 36 80mm diameter no 75AH 37 100mm diameter no 82AH 38 150mm diameter no 92AH 39 200mm diameter no 125AH 40 250mm diameter no 135AH 41 600mm diameter no 620AH 42 PSV ValvesAH 43 20mm diameter no 33AH 44 50mm diameter no 36AH 45 80mm diameter no 62AH 46 Mechanical EquipmentAH 47 Single piece of equipment of mass up to 500kg no 2400AH 48 Ditto of mass exceeding 500kg and up to 1000kg no 2800AH 49 Ditto of mass exceeding 1000kg and up to 2000kg no 3500AH 50 Ditto of mass exceeding 2000kg and up to 5000kg no 5500AH 51 Ditto of mass exceeding 5000kg and up to 10000kg no 8500

RETURN TO MENU

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

SCHEDULE OF RATES

Code Item Description Unit Supply Transport Erect total

PIPEWORK

AI HDPE PIPING TO SABS 533 PART IIFlanged piping in standard 6m lengthscomplete with stub ends welded on andgalvanising backing flanges

AI 1 Class 6AI 2 40mm S/F/B/E m 128.90 112.51 241.41AI 3 63mm S/F/B/E m 167.46 144.67 312.13AI 4 90mm S/F/B/E m 244.22 168.76 412.98AI 5 110mm S/F/B/E m 328.46 184.13 512.59AI 6 160mm S/F/B/E m 623.82 253.24 877.06AI 7 200mm S/F/B/E m 876.98 300.96 ###AI 8 250mm S/F/B/E m ### 391.58 ###AI 9 315mm S/F/B/E m ### 502.37 ###AI 10 400mm S/F/B/E m ### 945.31 ###AI 11 500mm S/F/B/E m ### ### ###AI 12 Class 10AI 13 25mm S/F/B/E m 120.10 112.51 232.61AI 14 50mm S/F/B/E m 156.80 119.13 275.93AI 15 75mm S/F/B/E m 235.29 162.05 397.34AI 16 125mm S/F/B/E m 490.38 202.56 692.94AI 17 180mm S/F/B/E m 943.82 270.05 ###AI 18 250mm S/F/B/E m ### 391.58 ###AI 19 355mm S/F/B/E m ### 658.37 ###AI 20 400mm S/F/B/E m ### 945.31 ###AI 21 450mm S/F/B/E m ### ### ###AI 22 500mm S/F/B/E m ### ### ###AI 23 Plain ended piping in standard 6m lengthsAI 24 Class 6AI 25 40mm P/E m 21.23 112.51 133.74AI 26 63mm P/E m 53.44 144.67 198.11AI 27 90mm P/E m 107.60 168.76 276.36AI 28 110mm P/E m 161.04 184.13 345.17AI 29 160mm P/E m 335.99 253.24 589.23AI 30 200mm P/E m 524.11 300.96 825.07AI 31 250mm P/E m 819.84 391.58 ###AI 32 315mm P/E m ### 502.37 ###AI 33 400mm P/E m ### 945.31 ###AI 34 500mm P/E m ### ### ###AI 35 Class 10AI 36 25mm P/E m 12.44 112.51 124.95AI 37 50mm P/E m 49.78 119.13 168.91AI 38 75mm P/E m 110.53 162.05 272.58AI 39 125mm P/E m 302.32 202.56 504.88AI 40 180mm P/E m 639.04 270.05 909.09AI 41 250mm P/E m ### 391.58 ###AI 42 355mm P/E m ### 658.37 ###AI 43 400mm P/E m ### 945.31 ###AI 44 450mm P/E m ### ### ###AI 45 500mm P/E m ### ### ###AI 46 Plain ended piping in non-standard lengths (per 1m)AI 47 Class 6AI 48 40mm m 3.54 18.75 22.29AI 49 63mm m 8.91 24.11 33.02AI 50 90mm m 17.93 28.13 46.06AI 51 110mm m 26.84 30.68 57.52

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

AI 52 160mm m 56.00 42.20 98.20AI 53 200mm m 87.35 50.48 137.83AI 54 250mm m 136.64 65.26 201.90AI 55 315mm m 219.60 83.73 303.33AI 56 400mm m 353.80 157.55 511.35AI 57 500mm m 555.10 253.20 808.30AI 58 Class 10AI 59 25mm m 2.07 18.75 20.82AI 60 50mm m 8.30 19.85 28.15AI 61 75mm m 18.42 27.00 45.42AI 62 125mm m 50.39 33.76 84.15AI 63 180mm m 106.51 45.00 151.51AI 64 250mm m 204.96 65.26 270.22AI 65 355mm m 412.36 109.72 522.08AI 66 400mm m 523.28 157.55 680.83AI 67 450mm m 661.24 197.15 858.39AI 68 500mm m 817.40 253.20 ###AI 69 Extra on piping in non-standard lengths for closuresAI 70 (Applicable only to B and C above) (1m Lengths S/F/O/E)AI 71 Class 6AI 72 40mm no 94.76 18.75 113.51AI 73 63mm no 106.47 24.11 130.58AI 74 90mm no 136.48 28.13 164.61AI 75 110mm no 174.53 30.68 205.21AI 76 160mm no 314.22 42.20 356.42AI 77 200mm no 405.69 50.48 456.17AI 78 250mm no 650.35 65.26 715.61AI 79 315mm no 881.70 83.73 965.43AI 80 400mm no ### 157.55 ###AI 81 500mm no ### 253.20 ###AI 82 Class 10AI 83 25mm no 93.29 18.75 112.04AI 84 50mm no 98.88 19.85 118.73AI 85 75mm no 126.74 27.00 153.74AI 86 125mm no 215.43 33.76 249.19AI 87 180mm no 378.40 45.00 423.40AI 88 250mm no 718.67 65.26 783.93AI 89 355mm no ### 109.77 ###AI 90 400mm no ### 157.55 ###AI 91 450mm no ### 197.15 ###AI 92 500mm no ### 253.20 ###AI 93 Unflanged site run piping in continuous lengths including measuringAI 94 on site and cutting to suit. ( Note: closures shall not be measured).AI 95 (1m Length + 1xSite Weld)AI 96 Class 6AI 97 40mm m 19.98 19.98AI 98 63mm m 25.35 25.35AI 99 90mm m 36.02 36.02AI 100 110mm m 46.57 46.57AI 101 160mm m 85.60 85.60AI 102 200mm m 121.89 121.89AI 103 250mm m 185.97 185.97AI 104 315mm m 293.60 293.60AI 105 400mm m 436.02 436.02AI 106 500mm m 672.10 672.10AI 107 Class 10AI 108 25mm m 18.51 18.51AI 109 50mm m 24.74 24.74AI 110 75mm m 34.86 34.86AI 111 125mm m 73.41 73.41AI 112 180mm m 139.40 139.40

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

AI 113 250mm m 254.29 254.29AI 114 355mm m 494.58 494.58AI 115 400mm m 605.60 605.60AI 116 450mm m 778.24 778.24AI 117 500mm m 934.40 934.40AI 118 Butt Weld/Shop WeldAI 119 Class 6AI 120 40mm no 16.44 54.69 71.13AI 121 63mm no 16.44 61.52 77.96AI 122 90mm no 18.09 67.20 85.29AI 123 110mm no 19.73 85.44 105.17AI 124 160mm no 29.60 119.61 149.21AI 125 200mm no 34.54 136.70 171.24AI 126 250mm no 49.33 153.80 203.13AI 127 315mm no 74.00 170.88 244.88AI 128 400mm no 82.22 222.14 304.36AI 129 500mm no 117.00 256.32 373.32AI 130 Class 10AI 131 25mm no 16.44 54.69 71.13AI 132 50mm no 16.44 58.09 74.53AI 133 75mm no 16.44 64.93 81.37AI 134 125mm no 23.02 85.44 108.46AI 135 180mm no 32.89 129.87 162.76AI 136 250mm no 49.33 153.80 203.13AI 137 355mm no 82.22 186.26 268.48AI 138 400mm no 82.22 222.14 304.36AI 139 450mm no 117.00 256.32 373.32AI 140 500mm no 117.00 256.32 373.32AI 141 Victualic or similar approved coupling complete AI 142 with two adaptorsAI 143 Class 6AI 144 40mm no 56.82 30.94 87.76AI 145 63mm no 56.82 39.79 96.61AI 146 90mm no 83.47 46.42 129.89AI 147 110mm no 83.47 50.64 134.11AI 148 160mm no 138.55 69.63 208.18AI 149 200mm no 202.56 76.40 278.96AI 150 250mm no 270.57 77.98 348.55AI 151 315mm no N/QAI 152 400mm no N/QAI 153 500mm no N/QAI 154 Class 10AI 155 25mm no 56.82 30.94 87.76AI 156 50mm no 56.82 32.77 89.59AI 157 75mm no 83.47 44.56 128.03AI 158 125mm no 83.47 55.71 139.18AI 159 180mm no 195.99 74.27 270.26AI 160 250mm no 270.57 77.98 348.55AI 161 355mm no N/QAI 162 400mm no N/QAI 163 450mm no N/QAI 164 500mm no N/QAI 165 Viking Johnson coupling completeAI 166 Class 6AI 167 40mm no 174.00 30.94 204.94AI 168 63mm no 174.00 39.79 213.79AI 169 90mm no 214.80 46.42 261.22AI 170 110mm no 260.40 50.64 311.04AI 171 160mm no 376.80 69.63 446.43AI 172 200mm no 470.40 76.40 546.80AI 173 250mm no 501.60 77.98 579.58

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

AI 174 315mm no 621.60 84.67 706.27AI 175 400mm no ### 111.41 ###AI 176 500mm no ### 139.26 ###AI 177 Class 10AI 178 25mm no 174.00 30.94 204.94AI 179 50mm no 174.00 32.77 206.77AI 180 75mm no 214.80 44.56 259.36AI 181 125mm no 260.40 55.71 316.11AI 182 180mm no 270.40 74.27 344.67AI 183 250mm no 501.60 77.98 579.58AI 184 355mm no 621.60 97.49 719.09AI 185 400mm no ### 111.41 ###AI 186 450mm no ### 120.32 ###AI 187 500mm no ### 139.26 ###AI 188 Compression couplingAI 189 Class 6AI 190 40mm no 30.90 30.94 61.84AI 191 63mm no 67.74 39.79 107.53AI 192 90mm no 155.62 46.42 202.04AI 193 110mm no 284.37 50.64 335.01AI 194 160mm no ### 69.63 ###AI 195 200mm no N/QAI 196 250mm no N/QAI 197 315mm no N/QAI 198 400mm no N/QAI 199 500mm no N/QAI 200 Class 10AI 201 25mm no 14.86 30.94 45.80AI 202 50mm no 42.10 32.77 74.87AI 203 75mm no 108.11 44.56 152.67AI 204 125mm no ### 55.70 ###AI 205 180mm no N/Q 74.27 74.27AI 206 250mm no N/QAI 207 355mm no N/QAI 208 400mm no N/QAI 209 450mm no N/QAI 210 500mm no N/QAI 211 Compression elbowAI 212 Class 6AI 213 40mm no 35.95 30.94 66.89AI 214 63mm no 64.05 39.79 103.84AI 215 63mm tee no 93.37 46.42 139.79AI 216 110mm no 297.32 50.64 347.96AI 217 160mm no N/QAI 218 200mm no N/QAI 219 250mm no N/QAI 220 315mm no N/QAI 221 400mm no N/QAI 222 500mm no N/QAI 223 Class 10AI 224 25mm no 15.36 30.94 46.30AI 225 50mm no 46.11 32.79 78.90AI 226 75mm no 109.92 46.42 156.34AI 227 125mm no N/QAI 228 180mm no N/QAI 229 250mm no N/QAI 230 355mm no N/QAI 231 400mm no N/QAI 232 450mm no N/QAI 233 500mm no N/QAI 234 Stub end complete with galvanised backing flange

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

AI 235 Class 6AI 236 40mm no 37.39 85.63 123.02AI 237 63mm no 40.56 101.31 141.87AI 238 90mm no 50.23 113.62 163.85AI 239 110mm no 63.98 136.08 200.06AI 240 160mm no 114.31 189.25 303.56AI 241 200mm no 141.90 213.10 355.00AI 242 250mm no 232.19 231.77 463.96AI 243 315mm no 294.06 255.55 549.61AI 244 400mm no 512.70 333.55 846.25AI 245 500mm no 695.54 395.58 ###AI 246 Class 10AI 247 25mm no 37.39 85.63 123.02AI 248 50mm no 37.39 101.31 138.70AI 249 75mm no 45.94 109.48 155.42AI 250 125mm no 71.01 140.67 211.68AI 251 180mm no 119.50 204.14 323.64AI 252 250mm no 232.19 231.77 463.96AI 253 355mm no 365.41 283.73 649.14AI 254 400mm no 512.70 333.55 846.25AI 255 450mm no 617.37 376.64 994.01AI 256 500mm no 695.54 395.58 ###AI 257 Chamfer stub end to suit internal diameter of matingAI 258 pipeAI 259 Class 6AI 260 40mm no 54.69 54.69AI 261 63mm no 61.52 61.52AI 262 90mm no 67.20 67.20AI 263 110mm no 85.40 85.40AI 264 160mm no 119.61 119.61AI 265 200mm no 136.70 136.70AI 266 250mm no 153.80 153.80AI 267 315mm no 170.88 170.88AI 268 400mm no 222.14 222.14AI 269 500mm no 256.32 256.32AI 270 Class 10AI 271 25mm no 54.69 54.69AI 272 50mm no 58.09 58.09AI 273 75mm no 64.93 64.93AI 274 125mm no 85.46 85.46AI 275 180mm no 129.87 129.87AI 276 250mm no 153.80 153.80AI 277 355mm no 186.24 186.24AI 278 400mm no 222.14 222.14AI 279 450mm no 256.32 256.32AI 280 500mm no 256.32 256.32AI 281 Bolt Set and bolt upAI 282 Class 6AI 283 40mm no 15.98 30.94 46.92AI 284 63mm no 15.98 39.79 55.77AI 285 90mm no 31.97 46.42 78.39AI 286 110mm no 32.16 50.64 82.80AI 287 160mm no 67.10 69.63 136.73AI 288 200mm no 67.10 76.40 143.50AI 289 250mm no 127.73 77.98 205.71AI 290 315mm no 133.49 84.67 218.16AI 291 400mm no 451.97 111.41 563.38AI 292 500mm no 564.90 139.26 704.16AI 293 Class 10AI 294 25mm no 15.98 30.94 46.92AI 295 50mm no 15.98 32.77 48.75

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

AI 296 75mm no 15.98 44.56 60.54AI 297 125mm no 32.16 55.71 87.87AI 298 180mm no 67.10 74.27 141.37AI 299 250mm no 127.73 77.98 205.71AI 300 355mm no 133.49 97.49 230.98AI 301 400mm no 451.97 111.41 563.38AI 302 450mm no 564.90 120.32 685.22AI 303 500mm no 564.90 139.26 704.16AI 304 Gasket and bolt set and bolt upAI 305 Class 6AI 306 40mm no 18.09 30.94 49.03AI 307 63mm no 19.49 39.79 59.28AI 308 90mm no 36.19 46.42 82.61AI 309 110mm no 38.33 50.64 88.97AI 310 160mm no 76.19 69.63 145.82AI 311 200mm no 78.43 76.40 154.83AI 312 250mm no 143.14 77.98 221.12AI 313 315mm no 153.41 84.67 238.08AI 314 400mm no 482.77 111.41 594.18AI 315 500mm no 611.40 139.20 750.60AI 316 Class 10AI 317 25mm no 18.09 30.94 49.03AI 318 50mm no 19.49 32.77 52.26AI 319 75mm no 36.19 44.56 80.75AI 320 125mm no 38.33 55.71 94.04AI 321 180mm no 76.19 74.27 150.46AI 322 250mm no 143.14 77.98 221.12AI 323 355mm no 153.41 97.49 250.90AI 324 400mm no 482.77 111.41 594.18AI 325 450mm no 611.40 120.32 731.72AI 326 500mm no 611.40 139.20 750.60AI 327 RUBBER LINED PIPINGAI 328 (Note: Rates to include for all r/ling toAI 329 piping, bends, fittings etc.)AI 330 Carbon Steel to SABS 62 Medium Wall AI 331 thickness piping scarfed plain ended lengths AI 332 with carbon steel standard weight flanged AI 333 ended fittings to SABS 62 and including AI 334 rubbber lining and flexible, welded or flangedAI 335 jointing as separately measuredAI 336 50 Diameter piping in standard 6m lengths m 126.5 35.64AI 337 Ditto, in non standard lengths m 126.5 35.64AI 338 50 Diameter closers no 55.517 251.64AI 339 80 Diameter butt welds no 39.809 74.52AI 340 50 Diameter bends no 342.43 35.64AI 341 50 Diameter tees no 366.3 47.52AI 342 80 Diameter concentric/eccentric reducers no 234.52 29.16AI 343 80 Diameter laterals no 366.3 49.68AI 344 80 Diameter cut in and branch weld no 58.3 118.8AI 345 50 Diameter flanges including welding on no 19.8 110.16AI 346 (1000/3)AI 347 50 Diameter blank flange no 70 12.96AI 348 50 Diameter Gasket and bolt set no 20 33.48AI 349 100 Diameter piping in standard lengths m 155.1 44.28AI 350 Ditto, in non standard lengths m 155.1 44.28AI 351 100 Diameter closers no 67.1 314.28AI 352 100 Diameter butt welds no 41.8 91.8AI 353 100 Diameter bends no 717.2 50.76AI 354 100 Diameter tees no 437.8 68.04AI 355 100 Diameter concentric/eccentric reducers no 271.7 39.96AI 356 100 Diameter laterals no 477.4 70.2

RETURN TO MENU

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

AI 357 100 Diameter cut in and branch weld no 74.8 151.2AI 358 100 Diameter flanges including welding on no 58.3 131.76AI 359 100 Diameter blank flange no 100.1 23.76AI 360 100 Diameter Gasket and bolt set no 26.4 62.64AI 361 125 Diameter piping in standard lengths m 203.5 56.16AI 362 Ditto, in non standard lengths m 203.5 56.16AI 363 125 Diameter closers no 86.9 374.76AI 364 125 Diameter butt welds no 58.3 110.16AI 365 125 Diameter bends no 977.9 59.4AI 366 125 Diameter tees no 628.1 74.52AI 367 125 Diameter concentric/eccentric reducers no 359.7 44.28AI 368 125 Diameter laterals no 629.2 76.68AI 369 125 Diameter cut in and branch weld no 85.8 178.2AI 370 125 Diameter flanges including welding on no 75.9 154.44AI 371 125 Diameter blank flange no 108.9 23.76AI 372 125 Diameter Gasket and bolt set no 31.9 66.96AI 373 150 Diameter piping in standard lengths m 221.1 61.56AI 374 Ditto, in non standard lengths m 221.1 61.56AI 375 150 Diameter closers no 94.6 421.2AI 376 150 Diameter butt welds no 64.9 124.2AI 377 150 Diameter bends no 917.4 70.2AI 378 150 Diameter tees no 734.8 85.32AI 379 150 Diameter concentric/eccentric reducers no 399.3 47.52AI 380 150 Diameter laterals no 779.9 87.48AI 381 150 Diameter cut in and branch weld no 99 203.04AI 382 150 Diameter flanges including welding on no 101.2 179.28AI 383 150 Diameter blank flange no 156.2 27AI 384 150 Diameter Gasket and bolt set no 40.7 68.04AI 385 Carbon Steel to SABS 719 Gr.B pipeworkAI 386 plain ended lengths with carbon steelAI 387 standard weight flanged ended fittingsAI 388 to SABS 719 Grade B. including AI 389 rubbber lining and flexible, welded or flangedAI 390 jointing as separately measuredAI 391 (6mm wall thickness)AI 392 200 Diameter piping in standard 9m lengths m 311.3 87.48AI 393 Ditto, in non standard lengths m 311.3 87.48AI 394 200 Diameter closers no 108.9 598.32AI 395 200 Diameter butt welds no 80.3 181.44AI 396 200 Diameter bends no 1389.3 118.8AI 397 200 Diameter tees no 1131.9 138.24AI 398 200 Diameter concentric/eccentric reducers no 719.4 71.28AI 399 200 Diameter laterals no 1137.4 139.32AI 400 200 Diameter cut in and branch weld no 106.7 286.2AI 401 200 Diameter flanges including welding on no 137.5 233.28AI 402 200 Diameter blank flange no 177.1 47.52AI 403 200 Diameter Gasket and bolt set no 56.1 77.76AI 404 250 Diameter piping in standard lengths m 398.2 105.84AI 405 Ditto, in non standard lengths m 398.2 105.84AI 406 250 Diameter closers no 140.8 725.76AI 407 250 Diameter butt welds no 103.4 218.16AI 408 250 Diameter bends no 1785.3 152.28AI 409 250 Diameter tees no 1554.3 180.36AI 410 250 Diameter concentric/eccentric reducers no 826.1 88.56AI 411 250 Diameter laterals no 1438.8 180.36AI 412 250 Diameter cut in and branch weld no 124.3 338.04AI 413 250 Diameter flanges including welding on no 159.5 293.76AI 414 250 Diameter blank flange no 270.6 60.48AI 415 250 Diameter Gasket and bolt set no 64.9 114.48AI 416 300 Diameter piping in standard lengths m 489.5 114.48AI 417 Ditto, in non standard lengths m 489.5 114.48

RETURN TO MENU

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

AI 418 300 Diameter closers no 137.5 114.48AI 419 300 Diameter butt welds no 99 114.48AI 420 300 Diameter bends no 2249.5 114.48AI 421 300 Diameter tees no 1841.4 114.48AI 422 300 Diameter concentric/eccentric reducers no 899.8 114.48AI 423 300 Diameter laterals no 1918.4 114.48AI 424 300 Diameter cut in and branch weld no 146.3 114.48AI 425 300 Diameter flanges including welding on no 210.1 114.48AI 426 300 Diameter blank flange no 360.8 114.48AI 427 300 Diameter Gasket and bolt set no 83.6 114.48AI 428 350 Diameter piping in standard lengths m 562.1 138.24AI 429 Ditto, in non standard lengths m 562.1 138.24AI 430 350 Diameter closers no 157.3 943.92AI 431 350 Diameter butt welds no 106.7 292.68AI 432 350 Diameter bends no 2644.4 281.88AI 433 350 Diameter tees no 2382.6 332.64AI 434 350 Diameter concentric/eccentric reducers no 1096.7 189AI 435 350 Diameter laterals no 2352.9 332.64AI 436 350 Diameter cut in and branch weld no 237.6 475.2AI 437 350 Diameter flanges including welding on no 282.7 406.08AI 438 350 Diameter blank flange no 477.4 101.52AI 439 350 Diameter Gasket and bolt set no 106.7 131.76AI 440 400 Diameter piping in standard lengths m 633.6 151.2AI 441 Ditto, in non standard lengths m 633.6 151.2AI 442 400 Diameter closers no 162.8 1049.76AI 443 400 Diameter butt welds no 117.7 331.56AI 444 400 Diameter bends no 3471.6 346.68AI 445 400 Diameter tees no 3045.9 371.52AI 446 400 Diameter concentric/eccentric reducers no 1219.9 205.2AI 447 400 Diameter laterals no 2875.4 400.68AI 448 400 Diameter cut in and branch weld no 189.2 509.76AI 449 400 Diameter flanges including welding on no 361.9 453.6AI 450 400 Diameter blank flange no 608.3 136.08AI 451 400 Diameter Gasket and bolt set no 154 165.24AI 452 450 Diameter piping in standard lengths m 717.2 176.04AI 453 Ditto, in non standard lengths m 717.2 176.04AI 454 450 Diameter closers no 199.1 1159.92AI 455 450 Diameter butt welds no 130.9 347.76AI 456 450 Diameter bends no 4100.8 388.8AI 457 450 Diameter tees no 3440.8 470.88AI 458 450 Diameter concentric/eccentric reducers no 1438.8 255.96AI 459 450 Diameter laterals no 3581.6 490.32AI 460 450 Diameter cut in and branch weld no 191.4 561.6AI 461 450 Diameter flanges including welding on no 420.2 522.72AI 462 450 Diameter blank flange no 717.2 152.28AI 463 450 Diameter Gasket and bolt set no 213.4 159.84AI 464 500 Diameter piping in standard lengths m 755.7 189AI 465 Ditto, in non standard lengths m 755.7 189AI 466 500 Diameter closers no 213.4 1245.24AI 467 500 Diameter butt welds no 138.6 376.92AI 468 500 Diameter bends no 4763 468.72AI 469 500 Diameter tees no 4514.4 571.32AI 470 500 Diameter concentric/eccentric reducers no 1741.3 330.48AI 471 500 Diameter laterals no 1787.5 598.32AI 472 500 Diameter cut in and branch weld no 224.4 589.68AI 473 500 Diameter flanges including welding on no 540.1 545.4AI 474 500 Diameter blank flange no 976.8 193.32AI 475 500 Diameter Gasket and bolt set no 213.4 213.84AI 476 600 Diameter piping in standard lengths m 1083.5 213.84AI 477 Ditto, in non standard lengths m 1083.5 213.84AI 478 600 Diameter closers no 237.6 213.84

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

AI 479 600 Diameter butt welds no 162.8 213.84AI 480 600 Diameter bends no 7698.9 213.84AI 481 600 Diameter tees no 6557.1 213.84AI 482 600 Diameter concentric/eccentric reducers no 2542.1 213.84AI 483 600 Diameter laterals no 6429.5 213.84AI 484 600 Diameter cut in and branch weld no 240.9 213.84AI 485 600 Diameter flanges including welding on no 897.6 213.84AI 486 600 Diameter blank flange no 1521.3 213.84AI 487 600 Diameter Gasket and bolt set no 244.2 213.84AI 488 A2 PIPINGAI 489 COPON LINEDAI 490 Carbon Steel to SABS 62 Medium Wall AI 491 thickness piping scarfed plain ended lengths AI 492 with carbon steel standard weight flanged AI 493 ended fittings to SABS 62 and including AI 494 copon lining and flexible, welded or flangedAI 495 jointing as separately measuredAI 496 15 Diameter piping in standard lengths m 13.2 23.76AI 497 Ditto, in non standard lengths m 13.2 23.76AI 498 15 Diameter closers no 42.9 160.92AI 499 15 Diameter butt welds no 30.8 49.68AI 500 15 Diameter bends no 121 22.68AI 501 15 Diameter tees no 174.9 29.16AI 502 15 Diameter concentric/eccentric reducers no 110 21.6AI 503 15 Diameter laterals no 181.5 29.16AI 504 15 Diameter cut in and branch weld no 49.5 72.36AI 505 15 Diameter flanges including welding on no 33 65.88AI 506 15 Diameter blank flange no 41.8 10.8AI 507 15 Diameter Gasket and bolt set no 6.6 25.92AI 508 20 Diameter piping in standard lengths m 15.4 24.84AI 509 Ditto, in non standard lengths m 15.4 24.84AI 510 20 Diameter closers no 44 169.56AI 511 20 Diameter butt welds no 30.8 52.92AI 512 20 Diameter bends no 143 25.92AI 513 20 Diameter tees no 179.3 31.32AI 514 20 Diameter concentric/eccentric reducers no 123.2 20.52AI 515 20 Diameter laterals no 181.5 28.08AI 516 20 Diameter cut in and branch weld no 51.7 75.6AI 517 20 Diameter flanges including welding on no 33 70.2AI 518 20 Diameter blank flange no 39.6 14.04AI 519 20 Diameter Gasket and bolt set no 6.6 29.16AI 520 25 Diameter piping in standard lengths m 20.9 29.16AI 521 Ditto, in non standard lengths m 20.9 29.16AI 522 25 Diameter closers no 46.2 29.16AI 523 25 Diameter butt welds no 31.9 29.16AI 524 25 Diameter bends no 128.7 29.16AI 525 25 Diameter tees no 187 29.16AI 526 25 Diameter concentric/eccentric reducers no 127.6 29.16AI 527 25 Diameter laterals no 185.9 29.16AI 528 25 Diameter cut in and branch weld no 51.7 29.16AI 529 25 Diameter flanges including welding on no 33 29.16AI 530 25 Diameter blank flange no 41.8 29.16AI 531 25 Diameter Gasket and bolt set no 6.6 29.16AI 532 40 Diameter piping in standard lengths m 30.8 28.08AI 533 Ditto, in non standard lengths m 30.8 28.08AI 534 40 Diameter closers no 44 189AI 535 40 Diameter butt welds no 30.8 56.16AI 536 40 Diameter bends no 160.6 27AI 537 40 Diameter tees no 198 34.56AI 538 40 Diameter concentric/eccentric reducers no 138.6 22.68AI 539 40 Diameter laterals no 52.8 88.56

RETURN TO MENU

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

AI 540 40 Diameter cut in and branch weld no 29.7 81AI 541 40 Diameter flanges including welding on no 38.5 10.8AI 542 40 Diameter blank flange no 14.3 30.24AI 543 40 Diameter Gasket and bolt set no 6.6 29.16AI 544 50 Diameter piping in standard lengths m 41.8 32.4AI 545 Ditto, in non standard lengths m 41.8 32.4AI 546 50 Diameter closers no 44 212.76AI 547 50 Diameter butt welds no 30.8 62.64AI 548 50 Diameter bends no 182.6 34.56AI 549 50 Diameter tees no 204.6 41.04AI 550 50 Diameter concentric/eccentric reducers no 137.5 25.92AI 551 50 Diameter laterals no 212.3 44.28AI 552 50 Diameter cut in and branch weld no 51.7 101.52AI 553 50 Diameter flanges including welding on no 35.2 87.48AI 554 50 Diameter blank flange no 40.7 12.96AI 555 50 Diameter Gasket and bolt set no 20.9 28.08AI 556 80 Diameter piping in standard lengths m 64.9 37.8AI 557 Ditto, in non standard lengths m 64.9 37.8AI 558 80 Diameter closers no 56.1 247.32AI 559 80 Diameter butt welds no 41.8 78.84AI 560 80 Diameter bends no 269.5 38.88AI 561 80 Diameter tees no 272.8 52.92AI 562 80 Diameter concentric/eccentric reducers no 172.7 33.48AI 563 80 Diameter laterals no 287.1 50.76AI 564 80 Diameter cut in and branch weld no 66 119.88AI 565 80 Diameter flanges including welding on no 39.6 106.92AI 566 80 Diameter blank flange no 78.1 14.04AI 567 80 Diameter Gasket and bolt set no 20.9 34.56AI 568 100 Diameter piping in standard lengths m 88 45.36AI 569 Ditto, in non standard lengths m 88 45.36AI 570 100 Diameter closers no 68.2 322.92AI 571 100 Diameter butt welds no 44 97.2AI 572 100 Diameter bends no 624.8 52.92AI 573 100 Diameter tees no 334.4 65.88AI 574 100 Diameter concentric/eccentric reducers no 210.1 37.8AI 575 100 Diameter laterals no 345.4 65.88AI 576 100 Diameter cut in and branch weld no 73.7 141.48AI 577 100 Diameter flanges including welding on no 48.4 135AI 578 100 Diameter blank flange no 97.9 23.76AI 579 100 Diameter Gasket and bolt set no 26.4 59.4AI 580 COPON LINEDAI 581 Carbon Steel to SABS 719 Gr.B pipeworkAI 582 plain ended lengths with carbon steelAI 583 standard weight flanged ended fittingsAI 584 to SABS 719 Grade B. including AI 585 copon lining and flexible, welded or flangedAI 586 jointing as separately measuredAI 587 (6mm wall thickness)AI 588 200 Diameter piping in standard 9m lengths m 202.4 86.4AI 589 Ditto, in non standard lengths m 202.4 86.4AI 590 200 Diameter closers no 103.4 561.6AI 591 200 Diameter butt welds no 75.9 177.12AI 592 200 Diameter bends no 922.9 102.6AI 593 200 Diameter tees no 731.5 135AI 594 200 Diameter concentric/eccentric reducers no 622.6 68.04AI 595 200 Diameter laterals no 855.8 135AI 596 200 Diameter cut in and branch weld no 116.6 277.56AI 597 200 Diameter flanges including welding on no 128.7 230.04AI 598 200 Diameter blank flange no 182.6 44.28AI 599 200 Diameter Gasket and bolt set no 67.1 74.52AI 600 250 Diameter piping in standard lengths m 276.1 104.76

RETURN TO MENU

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

AI 601 Ditto, in non standard lengths m 276.1 104.76AI 602 250 Diameter closers no 140.8 706.32AI 603 250 Diameter butt welds no 93.5 214.92AI 604 250 Diameter bends no 1108.8 141.48AI 605 250 Diameter tees no 904.2 160.92AI 606 250 Diameter concentric/eccentric reducers no 722.7 84.24AI 607 250 Diameter laterals no 1116.5 177.12AI 608 250 Diameter cut in and branch weld no 125.4 340.2AI 609 250 Diameter flanges including welding on no 149.6 305.64AI 610 250 Diameter blank flange no 268.4 59.4AI 611 250 Diameter Gasket and bolt set no 69.3 113.4AI 612 300 Diameter piping in standard lengths m 328.9 119.88AI 613 Ditto, in non standard lengths m 328.9 119.88AI 614 300 Diameter closers no 146.3 829.44AI 615 300 Diameter butt welds no 103.4 252.72AI 616 300 Diameter bends no 1228.7 209.52AI 617 300 Diameter tees no 1155 245.16AI 618 300 Diameter concentric/eccentric reducers no 825 125.28AI 619 300 Diameter laterals no 1349.7 245.16AI 620 300 Diameter cut in and branch weld no 148.5 388.8AI 621 300 Diameter flanges including welding on no 185.9 353.16AI 622 300 Diameter blank flange no 317.9 86.4AI 623 300 Diameter Gasket and bolt set no 94.6 124.2AI 624 350 Diameter piping in standard lengths m 361.9 141.48AI 625 Ditto, in non standard lengths m 361.9 141.48AI 626 350 Diameter closers no 170.5 955.8AI 627 350 Diameter butt welds no 113.3 290.52AI 628 350 Diameter bends no 1677.5 281.88AI 629 350 Diameter tees no 1390.4 329.4AI 630 350 Diameter concentric/eccentric reducers no 961.4 185.76AI 631 350 Diameter laterals no 1796.3 329.4AI 632 350 Diameter cut in and branch weld no 176 447.12AI 633 350 Diameter flanges including welding on no 251.9 415.8AI 634 350 Diameter blank flange no 438.9 100.44AI 635 350 Diameter Gasket and bolt set no 107.8 129.6AI 636 400 Diameter piping in standard lengths m 409.2 155.844AI 637 Ditto, in non standard lengths m 409.2 155.552AI 638 400 Diameter closers no 190.3 2144.88AI 639 400 Diameter butt welds no 133.1 319.68AI 640 400 Diameter bends no 2025.1 345.6AI 641 400 Diameter tees no 1786.4 382.32AI 642 400 Diameter concentric/eccentric reducers no 1123.1 203.04AI 643 400 Diameter laterals no 2152.7 382.32AI 644 400 Diameter cut in and branch weld no 198 502.2AI 645 400 Diameter flanges including welding on no 342.1 461.16AI 646 400 Diameter blank flange no 575.3 136.08AI 647 400 Diameter Gasket and bolt set no 163.9 163.08AI 648 450 Diameter piping in standard lengths m 467.5 171.72AI 649 Ditto, in non standard lengths m 467.5 171.72AI 650 450 Diameter closers no 198 1186.92AI 651 450 Diameter butt welds no 1238.6 356.4AI 652 450 Diameter bends no 2381.5 406.08AI 653 450 Diameter tees no 2326.5 477.36AI 654 450 Diameter concentric/eccentric reducers no 1317.8 249.48AI 655 450 Diameter laterals no 2384.8 484.92AI 656 450 Diameter cut in and branch weld no 210.1 555.12AI 657 450 Diameter flanges including welding on no 449.9 529.2AI 658 450 Diameter blank flange no 731.5 163.08AI 659 450 Diameter Gasket and bolt set no 210.1 169.56AI 660 600 Diameter piping in standard lengths m 618.2 228.96AI 661 Ditto, in non standard lengths m 618.2 228.96

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

AI 662 600 Diameter closers no 262.9 1533.6AI 663 600 Diameter butt welds no 173.8 470.88AI 664 600 Diameter bends no 3908.3 646.92AI 665 600 Diameter tees no 3111.9 810AI 666 600 Diameter concentric/eccentric reducers no 2273.7 427.68AI 667 600 Diameter laterals no 4671.7 806.76AI 668 600 Diameter cut in and branch weld no 270.6 719.28AI 669 600 Diameter flanges including welding on no 852.5 707.4AI 670 600 Diameter blank flange no 1387.1 308.88AI 671 600 Diameter Gasket and bolt set no 270.6 232.2AI 672 A2 PIPINGAI 673 Carbon Steel to SABS 62 Medium Wall AI 674 thickness piping scarfed plain ended lengths AI 675 with carbon steel standard weight flanged AI 676 ended fittings to SABS 62 and including AI 677 flexible, welded or flangedAI 678 jointing as separately measuredAI 679 15 Diameter piping in standard lengths m 8.8 24.84AI 680 Ditto, in non standard lengths m 8.8 24.84AI 681 15 Diameter closers no 39.6 153.36AI 682 15 Diameter butt welds no 27.5 49.68AI 683 15 Diameter bends no 94.6 24.84AI 684 15 Diameter tees no 143 31.32AI 685 15 Diameter concentric/eccentric reducers no 84.7 18.36AI 686 15 Diameter laterals no 138.6 31.32AI 687 15 Diameter cut in and branch weld no 47.3 75.6AI 688 15 Diameter flanges including welding on no 25.3 71.28AI 689 15 Diameter blank flange no 30.8 11.88AI 690 15 Diameter Gasket and bolt set no 6.6 28.08AI 691 20 Diameter piping in standard lengths m 13.2 28.08AI 692 Ditto, in non standard lengths m 13.2 28.08AI 693 20 Diameter closers no 44 165.24AI 694 20 Diameter butt welds no 30.8 51.84AI 695 20 Diameter bends no 115.5 28.08AI 696 20 Diameter tees no 146.3 30.24AI 697 20 Diameter concentric/eccentric reducers no 100.1 21.6AI 698 20 Diameter laterals no 148.5 30.24AI 699 20 Diameter cut in and branch weld no 51.7 78.84AI 700 20 Diameter flanges including welding on no 27.5 73.44AI 701 20 Diameter blank flange no 30.8 11.88AI 702 no 6.6 29.16AI 703 25 Diameter piping in standard lengths m 16.5 28.08AI 704 Ditto, in non standard lengths m 16.5 28.08AI 705 25 Diameter closers no 45.1 182.52AI 706 25 Diameter butt welds no 31.9 56.16AI 707 25 Diameter bends no 100.1 29.16AI 708 25 Diameter tees no 147.4 33.48AI 709 25 Diameter concentric/eccentric reducers no 102.3 20.52AI 710 25 Diameter laterals no 152.9 33.48AI 711 25 Diameter cut in and branch weld no 52.8 84.24AI 712 25 Diameter flanges including welding on no 26.4 75.6AI 713 25 Diameter blank flange no 33 10.8AI 714 25 Diameter Gasket and bolt set no 6.6 29.16AI 715 40 Diameter piping in standard lengths m 24.2 29.16AI 716 Ditto, in non standard lengths m 24.2 29.16AI 717 40 Diameter closers no 46.2 193.32AI 718 40 Diameter butt welds no 33 60.48AI 719 40 Diameter bends no 129.8 30.24AI 720 40 Diameter tees no 157.3 37.8AI 721 40 Diameter concentric/eccentric reducers no 108.9 22.68AI 722 40 Diameter laterals no 162.8 37.8

RETURN TO MENU

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

AI 723 40 Diameter cut in and branch weld no 53.9 88.56AI 724 40 Diameter flanges including welding on no 27.5 82.08AI 725 40 Diameter blank flange no 34.1 10.8AI 726 40 Diameter Gasket and bolt set no 14.3 31.32AI 727 50 Diameter piping in standard lengths m 34.1 31.32AI 728 Ditto, in non standard lengths m 34.1 31.32AI 729 50 Diameter closers no 46.2 218.16AI 730 50 Diameter butt welds no 33 66.96AI 731 50 Diameter bends no 145.2 37.8AI 732 50 Diameter tees no 165 45.36AI 733 50 Diameter concentric/eccentric reducers no 114.4 29.16AI 734 50 Diameter laterals no 172.7 45.36AI 735 50 Diameter cut in and branch weld no 53.9 103.68AI 736 50 Diameter flanges including welding on no 27.5 91.8AI 737 50 Diameter blank flange no 34.1 14.04AI 738 50 Diameter Gasket and bolt set no 23.1 32.4AI 739 80 Diameter piping in standard lengths m 52.8 41.04AI 740 Ditto, in non standard lengths m 52.8 41.04AI 741 80 Diameter closers no 55 265.68AI 742 80 Diameter butt welds no 39.6 83.16AI 743 80 Diameter bends no 226.6 39.96AI 744 80 Diameter tees no 221.1 56.16AI 745 80 Diameter concentric/eccentric reducers no 143 34.56AI 746 80 Diameter laterals no 228.8 56.16AI 747 80 Diameter cut in and branch weld no 62.7 125.28AI 748 80 Diameter flanges including welding on no 36.3 113.4AI 749 80 Diameter blank flange no 66 16.2AI 750 80 Diameter Gasket and bolt set no 25.3 39.96AI 751 100 Diameter piping in standard lengths m 66 48.6AI 752 Ditto, in non standard lengths m 66 48.6AI 753 100 Diameter closers no 67.1 324AI 754 100 Diameter butt welds no 47.3 100.44AI 755 100 Diameter bends no 506 56.16AI 756 100 Diameter tees no 273.9 65.88AI 757 100 Diameter concentric/eccentric reducers no 171.6 42.12AI 758 100 Diameter laterals no 289.3 70.2AI 759 100 Diameter cut in and branch weld no 78.1 150.12AI 760 100 Diameter flanges including welding on no 44 136.08AI 761 100 Diameter blank flange no 79.2 24.84AI 762 100 Diameter Gasket and bolt set no 42.9 66.96AI 763 150 Diameter piping in standard lengths m 138.6 63.72AI 764 Ditto, in non standard lengths m 138.6 63.72AI 765 150 Diameter closers no 99 429.84AI 766 150 Diameter butt welds no 70.4 128.52AI 767 150 Diameter bends no 564.3 23.76AI 768 150 Diameter tees no 462 31.32AI 769 150 Diameter concentric/eccentric reducers no 248.6 8.64AI 770 150 Diameter laterals no 476.3 28.08AI 771 150 Diameter cut in and branch weld no 106.7 195.48AI 772 150 Diameter flanges including welding on no 86.9 165.24AI 773 150 Diameter blank flange no 93.5 27AI 774 150 Diameter Gasket and bolt set no 42.9 70.2AI 775 Carbon Steel to SABS 719 Gr.B pipeworkAI 776 plain ended lengths with carbon steelAI 777 standard weight flanged ended fittingsAI 778 to SABS 719 Grade B. welded or flanged, AI 779 jointing as separately measuredAI 780 250 Diameter piping in standard lengths m 209 103.68AI 781 Ditto, in non standard lengths m 209 103.68AI 782 250 Diameter closers no 268.4 709.56AI 783 250 Diameter butt welds no 103.4 210.6

RETURN TO MENU

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

AI 784 250 Diameter bends no 869 60.48AI 785 250 Diameter tees no 733.7 72.36AI 786 250 Diameter concentric/eccentric reducers no 570.9 16.2AI 787 250 Diameter laterals no 876.7 72.36AI 788 250 Diameter cut in and branch weld no 121 334.8AI 789 250 Diameter flanges including welding on no 117.7 300.24AI 790 250 Diameter blank flange no 203.5 55.08AI 791 250 Diameter Gasket and bolt set no 66 115.56AI 792 500 Diameter piping in standard lengths m 390.5 185.76AI 793 Ditto, in non standard lengths m 390.5 185.76AI 794 500 Diameter closers no 201.3 1264.68AI 795 500 Diameter butt welds no 138.6 372.6AI 796 500 Diameter bends no 2380.4 221.4AI 797 500 Diameter tees no 2382.6 249.48AI 798 500 Diameter concentric/eccentric reducers no 1318.9 97.2AI 799 500 Diameter laterals no 2451.9 249.48AI 800 500 Diameter cut in and branch weld no 221.1 570.24AI 801 500 Diameter flanges including welding on no 402.6 562.68AI 802 500 Diameter blank flange no 756.8 189AI 803 500 Diameter Gasket and bolt set no 217.8 200.88AI 804 600 Diameter piping in standard lengths m 496.1 226.8AI 805 Ditto, in non standard lengths m 496.1 226.8AI 806 600 Diameter closers no 232.1 1437.48AI 807 600 Diameter butt welds no 162.8 450.36AI 808 600 Diameter bends no 3286.8 251.64AI 809 600 Diameter tees no 3406.7 338.04AI 810 600 Diameter concentric/eccentric reducers no 1780.9 114.48AI 811 600 Diameter laterals no 3633.3 338.04AI 812 600 Diameter cut in and branch weld no 242 707.4AI 813 600 Diameter flanges including welding on no 649 703.08AI 814 600 Diameter blank flange no 1183.6 297AI 815 600 Diameter Gasket and bolt set no 242 226.8AI 816 S2 PIPINGAI 817 ASTM A312 TP316 stainless steel schedule AI 818 40S BE piping, with SS flanges SABSAI 819 1123 T 1000/3 FFAI 820 15 Diameter piping in 6m standard lengths m 49.5 23.76AI 821 Ditto, in non standard lengths m 49.5 23.76AI 822 15 Diameter closers no 61.6 160.92AI 823 15 Diameter butt welds no 46.2 48.6AI 824 15 Diameter bends no 13.2 2.16AI 825 15 Diameter tees no 18.7 3.24AI 826 15 Diameter concentric/eccentric reducers no 15.4 21.6AI 827 15 Diameter laterals no 34.1 2.16AI 828 15 Diameter cut in and branch weld no 70.4 75.6AI 829 15 Diameter flanges including welding on no 74.8 70.2AI 830 15 Diameter blank flange no 30.8 10.8AI 831 15 Diameter PTFE Fluorocarbon 3mm thick gasket set no 15.4 27AI 832AI 833 20 Diameter piping in 6m standard lengths m 60.5 24.84AI 834 Ditto, in non standard lengths m 60.5 24.84AI 835 20 Diameter closers no 67.1 165.24AI 836 20 Diameter butt welds no 47.3 50.76AI 837 20 Diameter bends no 16.5 2.16AI 838 20 Diameter tees no 24.2 3.24AI 839 20 Diameter concentric/eccentric reducers no 18.7 2.16AI 840 20 Diameter laterals no 42.9 3.24AI 841 20 Diameter cut in and branch weld no 73.7 77.76AI 842 20 Diameter flanges including welding on no 86.9 71.28AI 843 20 Diameter blank flange no 39.6 11.88AI 844 20 Diameter PTFE Fluorocarbon 3mm thick gasket set no 22 29.16

RETURN TO MENU

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

AI 845AI 846 25 Diameter piping in standard lengths m 74.8 28.08AI 847 Ditto, in non standard lengths m 74.8 28.08AI 848 25 Diameter closers no 73.7 179.28AI 849 25 Diameter butt welds no 51.7 56.16AI 850 25 Diameter bends no 17.6 2.16AI 851 25 Diameter tees no 28.6 4.32AI 852 25 Diameter concentric/eccentric reducers no 17.6 2.16AI 853 25 Diameter laterals no 50.6 4.32AI 854 25 Diameter cut in and branch weld no 79.2 86.4AI 855 25 Diameter flanges including welding on no 93.5 76.68AI 856 25 Diameter blank flange no 42.9 10.8AI 857 25 Diameter PTFE Fluorocarbon 3mm thick gasket set no 6.6 27AI 858AI 859 40 Diameter piping in 6m standard lengths m 129.8 29.16AI 860 Ditto, in non standard lengths m 129.8 29.16AI 861 40 Diameter closers no 80.3 193.32AI 862 40 Diameter butt welds no 56.1 60.48AI 863 40 Diameter bends no 46.2 3.24AI 864 40 Diameter tees no 55 7.56AI 865 40 Diameter concentric/eccentric reducers no 30.8 2.16AI 866 40 Diameter laterals no 82.5 7.56AI 867 40 Diameter cut in and branch weld no 85.8 92.88AI 868 40 Diameter flanges including welding on no 125.4 82.08AI 869 40 Diameter blank flange no 71.5 10.8AI 870 40 Diameter PTFE Fluorocarbon 3mm thick gasket set no 15.4 31.32AI 871AI 872 50 Diameter piping in 6m standard lengths m 166.1 32.4AI 873 Ditto, in non standard lengths m 166.1 32.4AI 874 50 Diameter closers no 89.1 218.16AI 875 50 Diameter butt welds no 62.7 66.96AI 876 50 Diameter bends no 47.3 4.32AI 877 50 Diameter tees no 94.6 7.56AI 878 50 Diameter concentric/eccentric reducers no 47.3 3.24AI 879 50 Diameter laterals no 130.9 7.56AI 880 50 Diameter cut in and branch weld no 96.8 103.68AI 881 50 Diameter flanges including welding on no 159.5 93.96AI 882 50 Diameter blank flange no 94.6 12.96AI 883 50 Diameter PTFE Fluorocarbon 3mm thick gasket set no 24.2 31.32AI 884AI 885 80 Diameter piping in 6m standard lengths m 341 41.04AI 886 Ditto, in non standard lengths m 341 41.04AI 887 80 Diameter closers no 108.9 265.68AI 888 80 Diameter butt welds no 77 81AI 889 80 Diameter bends no 123.2 7.56AI 890 80 Diameter tees no 180.4 11.88AI 891 80 Diameter concentric/eccentric reducers no 84.7 4.32AI 892 80 Diameter laterals no 235.4 11.88AI 893 80 Diameter cut in and branch weld no 118.8 125.28AI 894 80 Diameter flanges including welding on no 223.3 112.32AI 895 80 Diameter blank flange no 150.7 15.12AI 896 80 Diameter PTFE Fluorocarbon 3mm thick gasket set no 24.2 35.64AI 897AI 898 100 Diameter piping in standard lengths m 495 49.68AI 899 Ditto, in non standard lengths m 495 49.68AI 900 100 Diameter closers no 134.2 321.84AI 901 100 Diameter butt welds no 91.3 99.36AI 902 100 Diameter bends no 242 11.88AI 903 100 Diameter tees no 292.6 17.28AI 904 100 Diameter concentric/eccentric reducers no 133.1 5.4AI 905 100 Diameter laterals no 366.3 17.28

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

AI 906 100 Diameter cut in and branch weld no 144.1 150.12AI 907 100 Diameter flanges including welding on no 291.5 136.08AI 908 100 Diameter blank flange no 200.2 25.92AI 909 100 Diameter PTFE Fluorocarbon 3mm thick gasket setno 26.4 66.96AI 910AI 911 Galvanised Carbon Steel medium weight to SABS 62AI 912 Screwed and socket jointed pipework inAI 913 standard 6m lengths with malleable ironAI 914 screwed fittings to SABS 509 AI 915 25 Diameter piping in standard lengths m 19.8 24.84AI 916 Ditto, in non standard lengths m 19.8 24.84AI 917 25 Diameter bends, spring and return bends no 6.6 125.28AI 918 25 Diameter equal tee no 5.5 30.24AI 919 25 Diameter reducing tee no 4.95 180.36AI 920 25 Diameter concentric reducer no 4.4 125.28AI 921 25 Diameter bronze taper seat union no 17.6 129.6AI 922 25 Diameter socket unions no 9.9 129.6AI 923 25 Diameter nipples no 3.3 3.24AI 924 25 Diameter reducing bush no 3.3 128.52AI 925 25 Diameter sockets no 4.4 78.84AI 926 25 Diameter caps no 3.3 77.76AI 927 25 Diameter flange to SABS 1123 - 1000/3 no 16.5 87.48AI 928 25 Diameter bolts and 3mm thick no 6.6 27AI 929 compressed asbestos fibre gasket setAI 930 50 Diameter piping in standard lengths m 39.6 33.48AI 931 Ditto, in non standard lengths m 39.6 33.48AI 932 50 Diameter bends, spring and return bends no 19.8 174.96AI 933 50 Diameter equal tee no 14.3 251.64AI 934 50 Diameter reducing tee no 16.5 251.64AI 935 50 Diameter concentric reducer no 7.7 178.2AI 936 50 Diameter bronze taper seat union no 26.4 189AI 937 50 Diameter socket unions no 18.7 189AI 938 50 Diameter nipples no 6.6 4.32AI 939 50 Diameter reducing bush no 5.5 174.96AI 940 50 Diameter sockets no 6.6 105.84AI 941 50 Diameter caps no 6.6 104.76AI 942 50 Diameter flange to SABS 1123 - 1000/3 no 16.5 115.56AI 943 50 Diameter bolts and 3mm thick AI 944 compressed asbestos fibre gasket set no 13.2 32.4AI 945 Carbon Steel to ASTM A106 GR.B plain endedAI 946 piping to schedule 40, butt welded endsAI 947 (All fittings to ANSI B16 Schedule 40)AI 948 40 Diameter piping in standard lengths m 42 28AI 949 Ditto, in non standard lengths m 42 28AI 950 40 Diameter closers no 12 363AI 951 40 Diameter butt welds no 45 235AI 952 40 Diameter bends no 10 5AI 953 40 Diameter tees no 28 8AI 954 40 Diameter concentric/eccentric reducers noAI 955 40 Diameter laterals noAI 956 40 Diameter cut in and branch weld noAI 957 40 Diameter flanges including welding on no 58 87AI 958 40 Diameter blank flange no 40 87AI 959 40 Diameter Gasket and bolt set no 8 26AI 960 50 Diameter piping in standard lengths m 45 28AI 961 Ditto, in non standard lengths m 45 28AI 962 50 Diameter closers no 14 363AI 963 50 Diameter butt welds no 50 235AI 964 50 Diameter bends no 12 5AI 965 50 Diameter tees no 30 8AI 966 50 Diameter concentric/eccentric reducers no

RETURN TO MENU

RETURN TO MENU

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

AI 967 50 Diameter laterals noAI 968 50 Diameter cut in and branch weld noAI 969 50 Diameter flanges including welding on no 65 87AI 970 50 Diameter blank flange no 45 87AI 971 50 Diameter Gasket and bolt set no 8 26AI 972 80 Diameter piping in standard lengths m 90 38AI 973 Ditto, in non standard lengths m 90 38AI 974 80 Diameter closers no 23 475AI 975 80 Diameter butt welds no 60 250AI 976 80 Diameter bends no 38 10AI 977 80 Diameter tees no 63 14AI 978 80 Diameter concentric/eccentric reducers noAI 979 80 Diameter laterals noAI 980 80 Diameter cut in and branch weld noAI 981 80 Diameter flanges including welding on no 72 112AI 982 80 Diameter blank flange no 68 112AI 983 80 Diameter Gasket and bolt set no 12 34AI 984 100 Diameter piping in standard lengths m 135 47AI 985 Ditto, in non standard lengths m 135 47AI 986 100 Diameter closers no 32 585AI 987 100 Diameter butt welds no 70 258AI 988 100 Diameter bends no 61 15AI 989 100 Diameter tees no 96 19AI 990 100 Diameter concentric/eccentric reducers noAI 991 100 Diameter laterals noAI 992 100 Diameter cut in and branch weld noAI 993 100 Diameter flanges including welding on no 79 138AI 994 100 Diameter blank flange no 90 142AI 995 100 Diameter Gasket and bolt set no 16 42AI 996 150 Diameter piping in standard lengths m 228 65AI 997 Ditto, in non standard lengths m 228 65AI 998 150 Diameter closers no 50 810AI 999 150 Diameter butt welds no 92 285AI ### 150 Diameter bends no 110 25AI ### 150 Diameter tees no 165 30AI ### 150 Diameter concentric/eccentric reducers noAI ### 150 Diameter laterals noAI ### 150 Diameter cut in and branch weld noAI ### 150 Diameter flanges including welding on no 92 190AI ### 150 Diameter blank flange no 135 197AI ### 150 Diameter Gasket and bolt set no 25 57AI ### Carbon Steel to ASTM A106 GR.B plain endedAI ### piping to schedule 40AI ### (All fittings to ANSI B16 Schedule 40)AI ### 200 Diameter piping in standard lengths mAI ### Ditto, in non standard lengths mAI ### 200 Diameter closers noAI ### 200 Diameter butt welds noAI ### 200 Diameter bends noAI ### 200 Diameter tees noAI ### 200 Diameter concentric/eccentric reducers noAI ### 200 Diameter laterals noAI ### 200 Diameter cut in and branch weld noAI ### 200 Diameter flanges including welding on noAI ### 200 Diameter blank flange noAI ### 200 Diameter Gasket and bolt set noAI ### 250 Diameter piping in standard lengths mAI ### Ditto, in non standard lengths mAI ### 250 Diameter closers noAI ### 250 Diameter butt welds noAI ### 250 Diameter bends no

RETURN TO MENU

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

AI ### 250 Diameter tees noAI ### 250 Diameter concentric/eccentric reducers noAI ### 250 Diameter laterals noAI ### 250 Diameter cut in and branch weld noAI ### 250 Diameter flanges including welding on noAI ### 250 Diameter blank flange noAI ### 250 Diameter Gasket and bolt set noAI ### 500 Diameter piping in standard lengths mAI ### Ditto, in non standard lengths mAI ### 500 Diameter closers noAI ### 500 Diameter butt welds noAI ### 500 Diameter bends noAI ### 500 Diameter tees noAI ### 500 Diameter concentric/eccentric reducers noAI ### 500 Diameter laterals noAI ### 500 Diameter cut in and branch weld noAI ### 500 Diameter flanges including welding on noAI ### 500 Diameter blank flange noAI ### 500 Diameter Gasket and bolt set noAI ### Typical "all in" ratesAI ### UPVC PIPINGAI ### 110mm Diameter buried upvc piping class 12 m 260/mAI ### 110mm Diameter buried upvc piping class 1 normal dut m 148/mAI ### 160mm Diameter buried upvc piping class 1 normal dut m 297/mAI ### 200mm Diameter buried upvc piping class 1 normal dut m 339/mAI ### Fire hydrant c/w hoses etc no 1200AI ### MILD STEEL FLANGED PIPING - Surface (INFRASTRUCTURE)AI ### 250mm NB piping m 570/mAI ### 200mm NB piping m 330/mAI ### 75mm NB piping m 96/mAI ### 50mm NB piping m 45/mAI ### 40mm NB piping m 39/m

RETURN TO MENU

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

SCHEDULE OF RATES

Code Description Unit Supply Transport Erect

ELECTRICAL WORKS

AK 1 LV CABLES:- PVCSWAPVC

AK 2 1.5mm2 x 3 core m 7.16 0.36 4.82AK 3 Ditto termination no 12.47 0.62 37.74AK 4 2.5mm2 x 3core m 7.76 0.39 4.82AK 5 Ditto termination no 12.47 0.62 37.74AK 6 2.5mm2 x 4core m 10.69 0.53 4.82AK 7 Ditto termination no 16.32 0.82 37.74AK 8 6mm2 x 3core m 13.27 0.66 7.35AK 9 Ditto termination no 16.33 0.82 56.65AK 10 6mm2 x 4core m 14.87 0.74 7.35AK 11 Ditto termination no 16.33 0.82 56.65AK 12 10mm2 x 3core m 19.55 0.98 7.35AK 13 Ditto termination no 16.33 0.82 76.24AK 14 10mm2 x 4core m 20.5 1.03 7.35AK 15 Ditto termination no 26.7 1.34 76.24AK 16 16mm2 x 3core m 21.51 1.08 7.35AK 17 Ditto termination no 40.24 2.01 121.98AK 18 25mm2 x 3core m 29.43 1.47 8.85AK 19 Ditto termination no 40.24 2.01 121.98AK 20 35mm2 x 3core m 37.76 1.89 8.85AK 21 Ditto termination no 40.24 2.01 152.48AK 22 50mm2 x 3core m 51.3 2.57 11.5AK 23 Ditto termination no 71.97 3.60 228.72AK 24 70mm2 x 3core m 66.7 3.34 14.82AK 25 Ditto termination no 71.97 3.60 304.96AK 26 95mm2 x 3core m 94.22 4.71 18.56AK 27 Ditto termination no 71.97 3.60 304.96AK 28 120mm2 x 3core m 114.23 5.71 18.56AK 29 Ditto termination no 133.13 6.66 381.2AK 30 150mm2 x 3core m 139.76 6.99 18.56AK 31 Ditto termination no 133.13 6.66 381.2AK 32 185mm2 x 3core m 169.41 8.47 22.9AK 33 Ditto termination no 220.53 11.03 510AK 34 10mm2 x 4core m 20.5 1.03 7.35AK 35 Ditto termination no 26.7 1.34 76.24AK 36 16mm2 x 4core m 26.01 1.30 7.35AK 37 Ditto termination no 40.24 2.01 121.98AK 38 25mm2 x 4core m 41.84 2.09 8.85AK 39 Ditto termination no 40.24 2.01 121.98AK 40 35mm2 x 4core m 49.39 2.47 8.85AK 41 Ditto termination no 40.24 2.01 152.48AK 42 50mm2 x 4core m 66.1 3.30 11.5AK 43 Ditto termination no 71.97 3.60 228.72AK 44 70mm2 x 4core m 88.45 4.42 14.82AK 45 Ditto termination no 71.97 3.60 304.96AK 46 95mm2 x 4core m 117.58 5.88 18.56AK 47 Ditto termination no 71.97 3.60 304.96AK 48 120mm2 x 4core m 147.27 7.36 18.56AK 49 Ditto termination no 133.13 6.66 381.2AK 50 150mm2 x 4core m 177.64 8.88 18.56AK 51 Ditto termination no 133.13 6.66 381.2AK 52 185mm2 x 4core m 216.86 10.84 22.9AK 53 Ditto termination no 220.53 11.03 510AK 54 MV CABLES (PVCSWAPVC XLPE)

AK 55 25mm2 x 3 core 11KV XLPE Cable m 80 4.00 13.86AK 56 Ditto, termination no 1100 55.00 485AK 57 35mm2 x 3 core 11KV XLPE Cable m 111 5.55 13.86AK 58 Ditto, termination no 1100 55.00 485

RETURN TO MENU

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

AK 59 50mm2 x 3 core 11KV XLPE Cable m 123 6.15 13.86AK 60 Ditto, termination no 1271 63.55 510AK 61 70mm2 x 3 core 11KV XLPE Cable m 148 7.40 20.22AK 62 Ditto, termination no 1271 63.55 510AK 63 95mm2 x 3 core 11KV XLPE Cable m 171 8.55 22.47AK 64 Ditto, termination no 1340 67.00 662AK 65 120mm2 x 3 core 11KV XLPE Cable m 198 9.90 24.72AK 66 Ditto, termination no 1364 68.20 662AK 67 150mm2 x 3 core 11KV XLPE Cable m 238 11.90 26.75AK 68 Ditto, termination no 1364 68.20 662AK 69 185mm2 x 3 core 11KV XLPE Cable m 278 13.90 29.42AK 70 Ditto, termination no 1500 75.00 728AK 71 600/1000V PVCSWAPVC Cu Cables

AK 72 2.5mm2 x 3core (cabtyre) m 7.99 0.40 4.82AK 73 Ditto termination no 12.47 0.62 37.74AK 74 2.5mm2 x 7core m 14.54 0.73 8.85AK 75 Ditto termination no 16.35 0.82 76.25AK 76 4mm2 x 3core m 9.95 0.50 4.82AK 77 Ditto termination no 16.33 0.82 37.74AK 78 4mm2 x 4core m 12.02 0.60 4.82AK 79 Ditto termination no 16.33 0.82 37.74AK 80 EARTHING:-

AK 81 2.5mm2 Bare Copper Earth Wire m 0.67 0.03 1.13AK 82 Ditto termination no

AK 83 6mm2 Bare Copper Earth Wire m 1.65 0.08 1.52AK 84 Ditto termination no

AK 85 16mm2 Bare Copper Earth Wire m 4.22 0.21 1.52AK 86 Ditto termination no

AK 87 25mm2 Bare Copper Earth Wire m 7.4 0.37 1.91AK 88 Ditto termination no

AK 89 70mm2 Bare Copper Earth Wire m 18.5 0.93 4.62AK 90 Ditto termination no 15 0.75 20AK 91 120mm2 Bare Copper Earth Wire m 22 1.10 6AK 92 Ditto termination noAK 93 RACKING:-

AK 94 (Heavy duty hot dip galvanised steel.)

AK 95 Straight runs

AK 96 150mm Wide m 102.62 5.13 26.96AK 97 300mm Wide m 112.73 5.64 33.71AK 98 600mm Wide m 144.93 7.25 68.53AK 99 1000mm Wide m 206.72 10.34 102.24AK ### Racking Supports

AK ### O-Line P1000 unistruts m 45 2.25 27AK ### 50x50x5mm Angle iron support m 15 0.75 20AK ### Junction Boxes

AK ### No 1 Pratley 3 Way Junction Boxes no 176.4 8.82 38AK ### No 1 Pratley 4 Way Junction Boxes no 210 10.50 45AK ### No 2 Pratley 3 Way Junction Boxes no 246 12.30 38AK ### No 2 Pratley 4 Way Junction Boxes no 281 14.05 45AK ### No 3 Pratley 3 Way Junction Boxes no 359 17.95 63AK ### No 3 Pratley 4 Way Junction Boxes no 402 20.10 75AK ### Aircraft Warning Lights

AK ### Aircraft warning lights CAT No. ZA742-13PL C/W Lam no 960 48.00 150AK ### Lights (Bulkhead)

AK ### 125W MV Wall Mounted Bulk head light no 513 25.65 50AK ### 70W HPS Wall Mounted Bulk head light no 551 27.55 50AK ### 100W HPS Wall Mounted Bulk head light no 755 37.75 50AK ### 2PL9 Wall Mounted Bulk head light no 269 13.45 50AK ### Lights (Fluorescent)

AK ### 1x58W-SS Open channel fluorescent luminaire no 97 4.85 50AK ### 2x58W-SS Open channel fluorescent luminaire no 109 5.45 50AK ### Lights (Flood)

AK ### 1000W Tungsten Halogen Flood Lights no 195 9.75 100AK ### 250W MV Flood light no 997 49.85 100

RETURN TO MENU

RETURN TO MENU

RETURN TO MENU

RETURN TO MENU

RETURN TO MENU

document.xls Revision 0 Approved : October 31, 2001

AK ### 400W MV Flood light no 1029 51.45 100AK ### Lights (High Bay)

AK ### 400W HPS High bay Sodium light no 769 38.45 100AK ### 250W MV HB Mercury Vapour light no 503 25.15 100AK ### 80W MV HB Mercury Vapour light no N/A N/AAK ### 1000W HPS High Bay Sodium light no 2399 119.95 100AK ### Galvanised Conduits and Accessories

AK ### 25mm Conduit m 12.64 0.63 15.25AK ### 32mm Conduit m 16.05 0.80 21AK ### Sundries

AK ### 16 Amp one lever, one way, light switch no 19.32 0.97 38.62AK ### 16 Amp one lever, two way, light switch no 24.18 1.21 57.97AK ### 16 Amp 220V switched socket outlet no 40.52 2.03 38.62AK ### Electric Photocell no 189 9.45 120AK ### Stop/Start Station c/w stand no 1404.32 70.22 150AK ### 16A Single pole light switch no N/A N/AAK ### Triple pole isolator no 378 18.90 50AK ### Telephone outlet point no 65 3.25 50AK ### 63A Waco Welding Plug no 1500 75.00 150AK ### 1x5KVA UPS Unit (25-30 mins) no 34500 1725.00 350AK ### 2 Compartment/3 Channel Power Skirting m 123.32 6.17 27AK ### Extract Fans GX9 Xpelair (GEC Woods) no 1185 59.25 120

RETURN TO MENU