AssphaAlht/Tr ppRlh/ MEMRemovUimTaemvU nTgS ......2019/03/29 · Asphalt/Tar Removal Using...
Transcript of AssphaAlht/Tr ppRlh/ MEMRemovUimTaemvU nTgS ......2019/03/29 · Asphalt/Tar Removal Using...
Asphalt/Tar Removal Using Solvent-Based FormulationsModified ASTM D4488 | Testing cleaning performance of products intended for use on resilient surfaces
Ingredient % by Weight
Elevance Clean® 1200 80
BIO-SOFT® N91-2.5 10
Butyl CarbitolTM 10
APPLICATION BULLETIN | Elevance Clean® 1200 | Asphalt and Tar Removal
ELEVANCE CLEAN® 1200 – ASPHALT AND TAR REMOVAL
Elevance Clean® 1200 is an effective industrial grade bio-based
ingredient used in aqueous and non-aqueous formulations
for cleaning tar, asphalt and bitumen from the surface of
tools, equipment and vehicles. It successfully addresses the
environmental, health and safety (EH&S) concerns of many
traditional ingredients currently on the market.
When compared to most petroleum-based solvents (e.g.
Benzene, Ethyl Benzene, Toluene, and Xylenes-BETX),
Elevance Clean® 1200 has an improved environmental
profile, and when compared to other bio-based products (e.g.
d-Limonene) Elevance Clean® 1200 is VOC-exempt. These
attributes of Elevance Clean® 1200 will allow formulators
maximum flexibility in developing products that will meet your
customers’ most challenging cleaning requirements.
The Elevance Clean® 1200 product line consists of two
products containing the same active material. Elevance Clean®
1200XA has no added fragrance while Elevance Clean® 1200HT
has fragrance added. The technical performance of both
products is identical.
All references to Elevance Clean® 1200 in this document refer
to both products.
Asphalt/Tar Removal Using Solvent-Based Formulations
Tar, Asphalt and Sealcoat Removal
Formulating cleaning products with Elevance Clean® 1200 provides the needed strength to eliminate these difficult-to-remove soils. Use of Elevance Clean® 1200 in formulations can make the cleaning process more effective and efficient. This is critical in applications such as cleaning asphalt and tar from trucks, rail cars and automotive parts. Elevance Clean® 1200 also retains its cleaning performance in cold temperatures and therefore provides ease in cleaning equipment during winter months.
0.00
10.00
20.00
30.00
40.00
50.00
60.00
70.00
80.00
90.00
100.00 % ASPHALT REMOVAL
40 CYCLES
Elevance Clean® 1200
d-Limonene Exxsol™ D60 Exxsol™ D110 Isopar™ L
Figure 1. Asphalt Spray and Rinse Cleaning Performance. High-concentration non-aqueous spray and rinse formulation using cleaning agents
Testing Methodology Section: 1
Asphalt/Tar Removal — Solvent-Based Formulations3" x 6" x 1/16" stainless steel plate coated with a uniform film of driveway asphalt sealcoat tar | 24 h cure @ 23 C | 5 mL solvent-imbibed cellulose pad | See formulation in table above | Gardner scrub apparatus | Image analysis software.
Asphalt/Tar Removal Using Water-Based Formulations
Modified ASTM D4488 | Testing cleaning performance of products intended for use on resilient surfaces
Ingredient % by Weight
Elevance Clean® 1200 5
BIO-SOFT® N91-6 or Empilan® KR 6 5
BIO-SOFT® D-40 12.5
Dowanol™ DPnB 5
Water 72.5
Elevance Clean® 1200 not only does an excellent job at removing asphalt and tar at ambient temperatures, but excels at removing these challenging soils at low temperatures for both routine, low-concentrate formulations and more concentrated spray and rinse formulations used for more heavily soiled surfaces.
Figure 2. Asphalt Spray and Rinse Cleaning Performance. High-concentration spray and rinse formulation using different cleaning agents
0%
10%
20%
30%
40%
50%
60%
70%
80%
90%
100%
30%
20%
75%
50%
90%
AMBIENT TEMPERATURE (25°C)
5% 5% 5%
15%
80%
COLD TEMPERATURE (-10°C)
AVG % ASPHALT REMOVED IN 30 CYCLES
ISOPAR™ M
ISOPAR™ HMINERAL SPIRITSELEVANCE CLEAN®1200
METHYL LAURATE
Testing Methodology Section: 2
Asphalt/Tar Removal — Water-Based Formulations 3” x 6” x 1/16” stainless steel plate coated with a uniform film of driveway asphalt sealcoat tar | 24 h cure @ 23C | 5 ml solvent-imbibed cellulose pad | See formulation in table above | Gardner scrub apparatus | Image analysis software
Industry Certifications
• VOC-exempt (40 CFR 59.203 — Standards for consumer products, U.S.)
• TSCA-listed and REACh-registered
• California Air Resource Board LVP VOC (CARB Method 310)
• Readily biodegradable by OECD Method 301
• Non-flammable (ASTM D-93) by OSHA standard 29 CFR 1910.106
• Reviewed by EPA’s Safer Choice program and qualifies for use in Safer Choice-labeled products
• Free of components listed in EU Dangerous Substances Directive (Regulation No. 1272/2008)
• Listed in the USDA BioPreferred® catalogue and CleanGredients inventory
ELEVANCE CLEAN® 1200 | ASPHALT AND TAR REMOVAL
1OSHA Standard 29 CFR 1910.1062Directive 2004/42/CE of the European Parliament and the Council3Title 40 CFR 59.203 – Standards for consumer products (U.S.)
Figure 3. ASTM D93 | Flash Point by Pensky-Martens Closed Cup Tester. Elevance Clean® 1200 is non-flammable in accordance with OSHA designations, imparting an added element of safe handling and transportation.
0.025.050.075.0
100.0125.0150.0175.0200.0
OXIDATION ONSET TEMPERATURE (°C)
Elevance Clean® 1200
165
Methyl Soyate
139
Aromatic150™
174
126
d-LIMONENE
167
Methyl Caprylate/Caprate
050
100150200250300350
INITIAL BOILING POINT (°C)
250°
C1
216°
C2
Elevance Clean® 1200
267
d-LIMONENE
184
AROMATIC150™
176
METHYL SOYATE
333
RHODIASOLV®
IRIS
196
020406080
100120140160180200
Elevance Clean® 1200
127
93°
C1
METHYLSOYATE
130
43
AROMATIC150™
62
d-LIMONENE
98
RHODIASOLV®
IRIS
FLASH POINT (CLOSED CUP, ºC)
Figure 5. ASTM E2009 | Oxidation Onset Temperature Using Pressurized Differential Scanning Calorimeter. Elevance Clean® 1200 demonstrates higher oxidative stability.
Figure 4. ASTM D2887 | Boiling Range Distribution of Petroleum Fractions by Gas Chromatography. Elevance Clean® 1200 exceeds VOC exempt classification requirements for the EU and U.S.2,3
LEVERAGE THE SUPERIOR CLEANING PERFORMANCE OF ELEVANCE CLEAN® 1200 TO BUILD YOUR BUSINESS.
ELEVANCE CLEAN® 1200 | ASPHALT AND TAR REMOVAL
Table 4. Dilutable Concentrate (2)
Ingredient % by Weight
Elevance Clean® 1200 24
BIO-SOFT® N91- 6 60
DOWANOL™ DPM 16
TOTAL 100
Table 5. Spray and Rinse (1)
Ingredient % by Weight
Elevance Clean® 1200 80
Tomadol® 91-2.5 or Berol® 533 10
Dowanol™ DPM 10
TOTAL 100
Table 6. Spray and Rinse (2)
Ingredient % by Weight
Elevance Clean® 1200 90
Tergitol™ 15-S-7 or Synperonic™ L7 5
Tergitol™ 15-S-9 or Synperonic™ A9 5
TOTAL 100
TO LEARN MORE AND REQUEST A SAMPLE:
www.elevance.com/products 866-625-7103 [email protected]
Headquartered in Woodridge, Ill., Elevance Renewable Sciences, Inc. is a high-growth specialty chemical company that creates novel specialty chemicals that perform better from renewable feedstocks, making the products that industry and consumers use every day better. Using a proprietary technology called olefin metathesis, the company helps industry deliver products that exceed the performance of existing products while leaving a smaller environmental footprint—for use in personal care products, detergents and cleaners, engineered polymers, lubricants and additives and other specialty chemicals markets. Visit www.elevance.com.
Copyright © 2019 Elevance Renewable Sciences. All rights reserved
Typical Formulations
Table 1. Ready-to-Use (1)
Ingredient % by Weight
Elevance Clean® 1200 5
BIO-SOFT® N91-6 or Empilan® KR 6 5
Calsoft® L40 12.5
STEPANATE® SXS-40 5
Water 72.5
TOTAL 100
Table 2. Ready-to-Use (2)
Ingredient % by Weight
Elevance Clean® 1200 0.5
BIO-SOFT® N91-6 or Empilan® KR 6 2.5
AMPHOSOL® CA or AMMONYX® LO 0.5
Sodium Citrate 0.5
Water 96
TOTAL 100
Table 3. Dilutable Concentrate (1)
Ingredient % by Weight
Elevance Clean® 1200 20
Tergitol™ 15-S-7 or Synperonic™ L7 10
Calsoft® L40 25
STEPANATE® SXS 6
EDTA Disodium Salt 0.3
Water Balance to 100
As of 03/29/2019