Associated Electrics, Inc. Customer Service 26021...
Transcript of Associated Electrics, Inc. Customer Service 26021...
11/1
2
2:: Introduction
:: KIT Features
:: Additional
:: Other Helpful Items
Associated Electrics, Inc.26021 Commercentre Dr.Lake Forest, CA 92630
http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook
Customer ServiceTel: 949.544.7500Fax: 949.544.7501
Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new RC10 B4.2. Please take a moment to read through this manual to help familiarize yourself with these steps.
We are continually changing and improving our designs; therefore, actual parts may appear slightly different than in the illustrations. New parts will be noted on supplementary sheets located in the appropriate parts bags. Check each bag for these sheets before you start to build.
Features in the B4.2 Factory Team:
• Factory Team 12mm “Big Bore” hard anodized, threaded aluminum shocks with TiN “Gold” 3mm shock shafts
• VTS slipper (variable torque, multi-plate slipper with 3 drive surfaces) and high-resolution spring
• Factory Team blue aluminum steering bellcrank set
• Factory Team 12mm blue aluminum front and rear clamping hexes with hex drive wheels
• Factory Team 7075-T6 blue aluminum 0° rear hubs with oversized outer bearing
• +8mm B4 chassis and Pro-Line Bulldog +8mm body
• Updated front and rear shock towers optimized for the 12mm ‘Big Bore’ shocks
• CVA joints with pin retainer clips
• Ball differential with light-weight outdrives
• Factory Team carbon fiber battery strap and blue aluminum thumb screws
• Complete set of precision ball bearings
• Factory Team blue titanium turnbuckles, blue aluminum hinge pin brace, milled motor plate, servo mounts, rear ballast weight and much more!
Your new B4.2 FT kit comes unassembledand requires the following items for completion (refer to catalog section for suggestions):• R/C two channel surface frequency radio system• AA-size batteries for transmitter (#302 alkaline, #303 rechargealble)• Electronic Speed Control, ESC (#29140, #29143)• Steering servo (#29166, #29167) • R/C electric motor • Pinion gear, size determined by type/wind of motor• Battery charger (a peak detection charger, or LiPo compatible charger)• 6 cell NiMH battery pack (#700) or a 2 cell LiPo battery pack (#714)
• Calipers or a precision ruler • Needle nose pliers• Lexan specific spray paint• Reamer / hole punch • Cyanacrylate glue (#1597) • Thread locking compound (#1596)• Tires and Inserts, Fronts and Rears
Tools included:• Allen wrenches #6950 (.050”, 1/16”, 3/32”, 5/64”)• Molded tools #6956• Camber gauge #1719
• Silicone Shock Fluid (Refer to catalog for complete listings)• Body Scissors (AE Part # 1737) • Reamer / Hole Punch • Wire Cutters • Hobby Knife • FT Hex Wrenches (AE Part # 1655) • Needle Nose Pliers • Multi Tool (AE Part #7494)• Soldering Iron • Calipers or a Precision Ruler • Green Slime shock lube (AE Part # 1105)
3:: Table of Contents
:: Notes
This symbols indicates a special note or instruction in the manual.
!There is a 1:1 hardware foldout page in the back of the manual. To check the size of a part, line up your hardare with the correct drawing until you find the exact size. Each part in the foldout has a number assigned to it for ordering replacement parts.
1................... Cover
2................... Introduction 3................... Table of Contents
4................... Steering Build (Bag A-AA)
4 - 5............. Front End, Outer Build (Bag B-BB)
5 - 6............. Front End, Inner Build (Bag C)
6 - 9............. Transmission Build (Bag D-DD)
9 - 11........... Rear End Build (Bag E-EE)
11 - 12........ CVA and Turnbuckle Build (Bag F-FF)
12 - 14........ Shocks Build (Bag G-GG)
14 - 16........ Electronics Build (Bag H-HH)
16 - 17........ Wheels, Tires and Body Install (Bag I)
17................. Servo Chart
18 - 19....... Tuning Tips
20 - 29....... Catalog
30................ Notes
31................ Setup Sheet “Kit Setup”
32................ 1:1 Hardware “Fold Out”
33................ Setup Sheet “Blank”
34................ Back Cover
Associated Electrics, Inc.26021 Commercentre Dr.Lake Forest, CA 92630
http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook
Customer ServiceTel: 949.544.7500Fax: 949.544.7501
:: Steering Build - Bag A-AA - Step 2
:: Front End, Outer Build - Bag B-BB - Step 1
4:: Steering Build - Bag A-AA - Step 1
Install the C Clip into the groove
shown below.
Do not overtighten steering bolts. Make sure there is free movement in the steering rack.
!
!
Build 2 (1 left, 1 right) Build 2!!
69224-40x1/2
fhcs
69154-40x5/8
fhcs
9637B4
chassis +8mm
9659Steering
brace9640
Steeringbolt(left)
6272Dust cover
foam
9659Block carrier
bushingx2
x2
x2
x2
3981Ballstud, .20 black, short
6276Ballstud, .20 silver, short
69174-40x3/8
bhcs
6272Dust cover
foam9679FT Aluminum Bellcrank Set
3971Steering rack
bearing
9566Top plate
89229Blue
countersunk washer
9563Front
bulkhead
9640Steering
bolt(right)
9659Steering
rack
x4
x3x3
x2
Be careful to not get thread lock on steering
rack bushings!
!
!
!
6272Dust cover
foam 7496B4 front axle, hex
31286FT ballstud
washer, aluminum
(2mm)
9880Steering
block, hex
6277Ballstud, .30 silver, long
39773/16x3/8bearing
9882C-clip, 3/16
44494-40x3/16aluminum
locknut
#1596
thread lock
5:: Front End, Outer Build - Bag B-BB - Step 2
:: Front End, Outer Build - Bag B-BB - Step 3
:: Front End, Inner Build - Bag C - Step 1
6272Dust cover
foam
x2
Align the C-clip onthe front axles
with the D-shape inside the
steering blocks.
!
39773/16x3/8bearing
98982-56x3/16
shcs
96452-56x1/8
bhcs
9665FT front
hinge pin brace
96452-56x1/8
bhcs
7922Spacer
989112mm aluminum clamping wheel hex, buggy front
73691/16
universalroll pin
9622Hinge pin,front outer
9621Hinge pin,front inner 9562
Front bumper
9622Hinge pin,front outer
9578B4 a-arms,
front
7922Caster block,
30°(1 left, 1 right)
3983Ballstud, .30 black, short
44494-40x3/16aluminum
locknut
x269154-40x5/8
fhcs
43342-56x5/16
bhcs
x2
6:: Front End, Inner Build - Bag C - Step 2
:: Front End, Inner Build - Bag C - Step 3
:: Transmission Build - Bag D-DD - Step 1
Front Camber Turnbuckle1.26” (32.00mm)
1.44” (36.50mm)Steering Turnbuckle
Orient the notch to the left
throughout the car. It indicates
which end has the left hand threads!
!
7230ball cup(large)
7666Drive rings
9852Ball diffoutdrives
9852Ball diffoutdrives
7666Drive rings
7230ball cup(large)
14062.00”
turnbuckle
14062.00”
turnbuckle
913114-40x7/8
bhcs
9568B4 front
shock tower
1780FT aluminum
shock bushings, standard
69244-40x3/8
shcs
6277Ballstud .30silver, long
65813/32 carbide
diff balls
7664Diff gear
52T
x2
x4x2
x12
x2
x2
x2
x2
Ball diffoutdrives
rings
31286FT ballstud
washer, aluminum
(2mm)
6272Dust cover
foam
x2
#6591diff lube
#6591diff lube
#6591diff lube
#1596
thread lock
7:: Transmission Build - Bag D-DD - Step 2
:: Transmission Build - Bag D-DD - Step 3
:: Transmission Build - Bag D-DD - Step 4
As you tighten the diff bolt, you will notice the T-nut ears moving closer to the bottom of the outdrive slot. This compresses the spring behind the T-nut. The spring should be completely com-
pressed at the same time the T-nut reaches the end of the slot. Caution! Pay close attention to the feeling when the spring is
completely compressed. Do not overtighten the bolt. When you feel the spring completely compressed, loosen the diff bolt 1/8” of a turn. Your diff should now operate smoothly with resistance
as the outdrives move in opposite directions. After you have driven the car once, re-check the diff setting.
9601Top shaft
9602Top shaft
spacer
9826Transmission case(1 left, 1 right)
3977Ball bearing
3/16x3/8
9361Idler gear
shaft
9360Idler gear
3977Ball bearing
3/16x3/8
9832Ball bearing10x16mm
6575Diff
cover
6575Locking
t-nut
6582Diff
thrust spring
#6588
black grease
x2
x2
x2
x2
6573Diff thrust
washer
65895/32 x 5/16,
unflangedbearing
65745/64 diff
thrust balls
6573Diff thrust
bolt
x2
x2
x6
8:: Transmission Build - Bag D-DD - Step 5
:: Transmission Build - Bag D-DD - Step 6
:: Transmission Build - Bag D-DD - Step 7
x2
7485FT V2
slipper hub
91177VTS
slipper pads
9603Slipper
pad
965181T 48Pspur gear
91176VTS slipper
housing
91178VTS slipper
plate91179
VTS slipper hub, outer
#1596thread lock
#1596
thread lock
69194-40x5/16
bhcs
69254-40x1/2
shcs
69134-40x1 1/4
shcs
1770FT milled
motor plate(blue)
69284-40x1
shcs
9587Wing mounts
(1 left, 1 right)
9819Motor guard
9630.030 ballstud
washer
x2
x3
x2
x3
There’s also a 75T 48P Spur Gear
(#9650)included for stock
motors use!!
!
!
9:: Transmission Build - Bag D-DD - Step 8
:: Rear End Build - Bag E-EE - Step 1
:: Rear End Build - Bag E-EE - Step 2
Set nut flush with top shaft.
See page 18 for gear mesh, and slipper clutch
setting instructions!
!
!!
7487Anti-squat shim
(2 degrees)
9621Hinge pin, rear inner
9582Rear B4 a-arms (1 left, 1 right)
96452-56x1/8
bhcs
66295-40
locknut
9739Slipper spring
9818Rear chassis
plate
7487Rear arm
mount(3.0 degree)
7486V2 slipper
washer
x2
x2
x2
Compress spring first.
!
92695-40x1/2
fhcs
92695-40x1/2
fhcs
x2 x4
10:: Rear End Build - Bag E-EE - Step 3
:: Rear End Build - Bag E-EE - Step 4
:: Rear End Build - Bag E-EE - Step 5
6277Ballstud .30silver, long
96445-40x9/16
shcs74134-40x3/4
bhcs
9564Rear chassis
brace
96435-40x7/16
shcs
96435-40x7/16
shcs
69224-40x1/2
fhcs
7488Rear ballast
weight
31286FT ballstud
washer, aluminum
(1mm)
x2
x2
x2
x2
x2
x2
x2
6272Dust cover
foam
1781FT aluminum
shock bushing, short
x2
x2
#1596thread lock
Use inside hole in chassis brace!
!
11:: Rear End Build - Bag E-EE - Step 6
:: CVA and Turnbuckles Build - Bag F-FF - Step 1
:: CVA and Turnbuckles Build - Bag F-FF - Step 2
Build x2 (right and left side)
1 drop!CA glue not
included
Align the gap in the pin retainer
to be opposite of the CVA pin.
!
#1597ca glue
Build x2
39773/16x3/8bearing
9864FT aluminum
hub ( 0˚)
44494-40x3/16aluminum
locknut
6272Dust cover
foam
7933Crush tube
3981Ballstud, .20black, short
9917Aluminum
hub A, carbon
7935.187x.196bearing
73683/16 axle
shim
Left Side
7381CVA coupler
7996CVA pinretainer
9755CVA axle
rear
9672CVA bone
7381CVA cross
pin
#6588
black grease
62884-40x1/4
bhcs
x2
69244-40x3/8
shcs69154-40x5/8
fhcs
x2
x2
12:: CVA and Turnbuckles Build - Bag F-FF - Step 3
:: CVA and Turnbuckles Build - Bag F-FF - Step 4
:: Shocks Build - Bag G-GG - Step 1
73691/16
roll pins
989012mm aluminumclamping wheel hex, buggy rear
Build x2 (right and left side)
Build x2 (right and left side)
Build x2 (right and left side)
1/16roll pins
12mm aluminumclamping wheel hex, buggy rear
Orient the notch to the left
throughout the car. It indicates
which end has the left hand threads!
!
9130812mm shock
piston (1.6 front)(1.6 rear)
9130521x3 TiN
shock shaft (front)
9130627.5x3 TiN shock shaft
(rear)
62991/8 E-clip
62991/8 E-clip
4187Nylon spacer,
(.030)
Racers Tip:
Use a marker over the numbers on the pistons to
make them easily visible!
!
Front:3 spacers
Rear:2 spacers
98982-56x3/16
shcs9645
2-56x1/8bhcs
31286FT ballstud
washer, aluminum
(1mm)
9622Hinge pin,rear outer
9630.030 ballstud
washer
Rear Camber Turnbuckle1.28” (32.25mm)
7230ball cup(large)
14062.00”
turnbuckle
x2
13:: Shocks Build - Bag G-GG - Step 2
:: Shocks Build - Bag G-GG - Step 3
:: Shocks Build - Bag G-GG - Step 4
1777FT shock pivot ball
1777Shock eyelet
#1105green slime
9129912x23mm
shock bodies (front)
9130112x31mm
shock bodies (rear)
91309Shock hat bushing
91309Shock spacer
5407O-ring
31327VCS3 shock bottom cap
31327VCS3 shock bottom cap
o-ring
9130912mm shock cap o-ring
x2
x2
#1105green slime
Racers Tip:
Lightly rub shock oil on the o-ring before installation!
Racers Tip:
Coating the o-rings with green slime
(#1105) helps seal & reduce o-ring
swell! Green slime not included in kit!
!
!
x49130312mm
shock cap
Step 9-10Step 8Step 6-7Step 4-5
Front Shock: 30 wt
Rear Shock: 30 wt
Step 2-3
31510M2x4mm
bhcs
91309Shock cap
o-ring
x4
x4Shock Bleeding Steps:1. Before assembly, get each bleed
screw and thread it 1-2 turns into the shock cap. This will make installation easier when you are bleeding your shocks.
2. Pull shock shaft down.3. Fill shock body 3/4 full with silicone
shock fluid.4. Slowly move the shock shaft up and
down to remove air from under the piston.
5. Wait for bubbles to come to surface.6. Fill shock body to top with silicone
shock fluid.7. Place a drop of oil in the cap and on
cap threads.8. Install cap (without bleed screw) and
tighten completely.9. Slowly compress shaft all the way to
bleed excess silicone shock fluid out the hole in the cap (use rag around-shock to catch excess fluid).
10. Install M2x4mm button head screw until snug while shaft is fully com-pressed.
Shock oil#5422Sh
ock oil
#5422
x4x4
9131012mm shock spring cup
(5mm offset)
9132612mm front spring, Black
(3.00lb)
9133712mm rear
spring, white (2.10lb)
9130412mm
threaded collar
9130412mm
threaded collar o-ring
x4
x4Front: 4mm
Rear: 7mm
Build x2 front and x2 rear shocks
Racers Tip:
Use your finger to rub shock oil on the o-ring for
smoother adjustment!
!
!
!
14:: Shocks Build - Bag G-GG - Step 5
:: Electronics Build - Bag H-HH - Step 1
:: Electronics Build - Bag H-HH - Step 2
Offset the servo horn by 5-10 degrees
(approximately one notch)! (approximately one notch)!
Use outside hole in
front arm!
!Use outside
hole in front arm!
!
Offset the servo horn by 5-10 degrees
(approximately one notch)(approximately one notch)
9170Servo link
7337Gold
washer
89007Servo horn
ring
3981Ballstud, .20 black, short
6272Dust cover
foam
9180Servohorn
1779FT Servo mount
x4
x2
x2x2
x2
7336Servo
spacers
69174-40x3/8
bhcs
62924-40x3/8
fhcs
Servo not included!
Servo screwnot included!
6472Shock
mount nut
x2
69254-40x1/2
shcs
x2
Use inside hole in
rear arm!
!
69274-40x3/4
shcs
x2
6472Shock
mount nut
x2
Leave a 2mm gap!
!
See page 17 for correct servo spacing on the
servo chart!!
15:: Electronics Build - Bag H-HH - Step 3
:: Electronics Build - Bag H-HH - Step 4
:: Electronics Build - Bag H-HH - Step 5
6338Antenna
tube & cap
38625-40x1/8set screw
Receiver / Servo tapenot included!
ESC/ Servo tapenot included!
Pinion / Setscrewnot included!
Motor not included!
7461Gear cover
(clear)
7461Gear cover
button
6936Washer #4aluminum
62854-40x1/4
shcs
31532M3x8mm
bhcs
x2
x2
x2
See page 18 for gear mesh setting
instructions!!
16:: Electronics Build - Bag H-HH - Step 6
:: Wheels / Tires and Body - Bag I - Step 2
:: Wheels / Tires and Body - Bag I - Step 1
69538-32
LP steellocknut
x2
Tires / Insertsnot included!
Tires / Insertsnot included!
#1597
ca glue #1597
ca glue
x29696Buggy rear wheel hex,
yellow
9638B4+8mm
battery strap, carbon
9691Buggy front wheel hex,
yellow
x2
Carefully apply tire adhesive to the tire bead on
both sides.Do one side at a time, allow it to
dry before gluing the other side!
!
x269528-32
locknut, steel
17874-40x1/2set screw
1787FT battery
strap thumb screws
9238Foam
battery spacer
x2x2 x2
x2
Batterynot included!
17:: Wheels / Tires and Body - Bag I - Step 3
:: Wheels / Tires and Body - Bag I - Step 4
:: Servo Chart
Painting Tips:Body : Your B4.2 FT comes with a clear polycarbonate body. You will need to prep the body before you can paint it. Wash the inside thoroughly with warm water and liquid detergent. Dry the body using a clean, soft, lint-free cloth. Use the supplied window masks to cover the windows from the INSIDE of the body (RC cars get painted from the inside). Using high quality masking tape, apply tape to the inside of the body to create a design. Spray (either rattle can or airbrush) the paint to the inside of the body (prefferably dark colors first, lighter colors last).
NOTE: use ONLY paint that is recommended for use with (polycarbonate) plastics. If you don’t, you candestroy the plastic body!!!!).
After painting, cut the body along the trim lines. Make sure to drill or use a body reamer to make the holes for the body mounts and antenna!
Steering Servo ChartAssociated
* Not all servo’s are listed* Make sure servo linkage clears the servo through full travel in both directions. Use #7336 servo spacers to adjust the servos position (to make the steering link as straight as possible)
XP-1015, XP-1313 F
F
F
A
A
H
H
J
J
J
# 9180servo arm
94102
HS-5625MG, HS-5645MG, HS645MG
Z4750, Z2750
Z250, Z550
S9204, S9250, S9450
S9404
94257, 94258, 94357, 94358, 94452, 94453, 94755
HS-965, HS-985MG, HS-5965, HS-5985MG
PS-401, PS-2001, PS-2004, PS-2015, PS-2173, PS-2174, PS-2123, PS-2143, PS-2144
Airtronics
Airtronics
Hitec
Hitec
JR
JR
Futaba
Futaba
KO
x29587Wing shims
69294-40x3/8
shcs(w/hole)
x26332Body clips
*Racers Tip:Instead of using the included body clips (#6332) and the #6929 SHCS for the top
plate to install your body, you can use hook and loop tape
on the inside of the body, and the sides of the chassis to
keep your body in place!
!
18:: Tuning TipsTips for Beginners:
Before making any changes to the standard setup, make sure you can get around the track without crashing. Changes to your vehicle will not be beneficial if you can’t stay on the track. Your goal is consistent laps.
Once you can get around the track consistently, start tuning your vehicle. Make only ONE adjustment at a time, testing it before making another change. If the result of your adjustment is a faster lap, mark the change on the included setup sheet (make adddtional copies of the sheet before writing on it). If your adjustment results in a slower lap, revert back to the previous setup and try another change.
When you are satisfied with your vehicle, fill in the setup sheet thoroughly and file it away. Use this as a guide for future track days or conditions.
Peridicaly check all moving suspension parts. Suspension components must be kept clean and move freely without binding to prevent poor and/or inconsistent handling.
Motor Maintenance:
Brushed motors require frequent maintenance to keep performance levels at their maximum. Between runs and after letting the motor cool completely, inspect the brushes to ensure that they are moving freely in their holders. Remove the springs and slide the brushes in and out of their holders checking for any resistance or rough spots. If found, remove the brush and carefully wipe it clean. Removing buildup will allow the brush to slide freely and create maximum contact with the commutator resulting in maximum power output.After every 3-5 runs, remove the brushes from their holders and inspect the tips for wear or burning. If there is noticeable wear (less than 75% of the brush remaining), it is best to cut the commutator and replace the brushes with a new pair. If the tips become a burned blue color, the lubricant in the brush has been burned away and new brushes should be installed.Occasionally, the motor should be cleaned with a soft brush to prevent dirt build up around the brush hood area and ball bearings. At this time, it is a good idea to add one drop of bushing / bearing oil to each bushing or ball bearing.
If using a brushless motor, please refer to the motor manufacturer’s guidelines for proper maintenance.
Slipper Clutch:
The assembly instructions give you a base setting for your clutch. Turn the nut on the shaft so that the end of the top shaft is even with the outside of the nut. At the track, tighten or loosen the nut in 1/8 turn increments until you hear a faint slipping sound for 1-2 feet on takeoffs. Another popular way to set the clutch is to hold both rear tires firmly in place and apply short bursts of throttle. If the clutch is properly set, the front tires should lift slightly up off the surface.
Motor Gearing:
Proper motor gearing will result in maximum performance and run time while reducing the chance of overheating and premature motor failure. The gear ratio chart lists recommended starting gear ratios for the most widely used motor types. Gear ratios will vary depending upon motor brand, wind, and electronic speed control. Consult your motor and electronic speed control manufacturers for more information. Team Associated is not responsible for motor damage due to improper gearing. * These gearings are for use with advanced timing speed control settings!
Set The Gear Mesh:
You should be able to rock the spur gear back and forth in the teeth of the pinion gear without making the pinion gear move. If the spur gear mesh is tight, then loosen the #31532 screws and move the motor away, then try again. A gear mesh that is too tight or too loose will reduce power and damage the gear teeth.
27T Reedy Stock19T Reedy Super Stock
17.5 Reedy Sonic Brushless *17.5 Reedy Sonic Brushless
13.5 Reedy Sonic Brushless *13.5 Reedy Sonic Brushless10.5 Reedy Sonic Brushless9.5 Reedy Sonic Brushless8.5 Reedy Sonic Brushless7.5 Reedy Sonic Brushless6.5 Reedy Sonic Brushless
3300kV Brushless3900kV Brushless4900kV Brushless6100kV Brushless
232223322230242322212121211918
818178758175818181818181818181
9.16:19.57:18.82:16.09:19.57:16.50:18.78:19.15:19.57:1
10.03:110.03:110.03:110.03:111.08:111.70:1
Motor Pinion Spur FDRB4.2 Gear Ratio Chart (Internal Gear Ratio 2.60:1)
19:: Tuning Tips (cont.)Front Camber Links:
Changing the length of the camber link is considered a bigger step than adjusting the ball end height on the tower. Shortening the camber link (or lowering the ball end) will give the front end less roll and quicken steering response. Lengthening the camber link (or raising the ball end) will give the front more roll and slower steering response. Longer camber links are typically used on high grip tracks and shorter links tend to work better on medium-grip loose tracks.
*Raise or lower the ball end by adding
or subtracting washers here
!
Caster:
Caster describes the angle of the kingpin as it leans toward the rear of the vehicle. Positive caster means the kingpin leans rearward at the top. The supplied 30° caster blocks (#7922) are recommended in most cases. For less corner entry steering and more exit steering, try the optional 25° blocks (#7919).
Rear Camber Link:
Changing the length of the camber link is considered a bigger step than adjusting the ball end height on the rear chassis brace. Shortening the camber link (or lowering the ball end) will give the rear end less roll and the car will tend to accelerate or “square up” better. Lengthening the camber link (or raising the ball end) will give the rear more roll and more cornering grip. Longer camber links are typically used on high grip tracks, while shorter links tend to work better on medium grip loose tracks. The kit setting is the best compromise of cornering grip and acceleration.
Wheelbase Adjustment:
You have three options for rear hub spacing, Forward, Middle, & Back. The kit setting provides the most rear traction, and will be used most often. For improved handling in bumps or rhythm sections, try moving the hubs to the Middle or Back position. This can also make the car handle better in 180° turns.
Rear Camber:
Camber describes the angle at which the tire and wheel rides when looked at from the back. Negative camber means that the tire leans inward at the top. A good starting camber setting is -1°. Use the included #1719 camber gauge to set your camber. Adding a small amount of positive camber, where the top of the tire is leaning out, will tend to improve straight-line acceleration on loose tracks.
Anti-Roll Bars:
The optional #9635 rear anti-roll bar kit (also called the “swaybar”) allows you to add roll resistance to the rear end with minimal effect on handling over bumps and jumps. It is an especially helpful tuning item on high-grip tracks (try the gold bar). The silver and black anti-roll bars are typically used on medium-grip loose tracks.
Ride Height:
Ride height is the distance from the ground to the bottom of the chassis.The standard front ride height setting is with the front arms level (reffered to as “arms level”) or 24mm (Ride Height Gauge #1449). Check the ride height by lifting up the entire car about 8-12 inches off the bench and drop it. After the suspension “settles” into place, measure ride height (Ride Height Gauge #1449). Raise or lower the shock collars as necessary so that the left & right arms appear to be level.
The rear ride height setting you should use most often is with the outdrive, driveshaft, and axles all on the same imaginary horizontal line (reffered to as “bones level”) or 24mm (Ride Height Gauge#1449). Check the ride height by lifting up the entire car about 8-12 inches off the bench and drop it. After the suspension “settles” into place, measure ride height (Ride Height Gauge #1449). Raise or lower the shock collars as necessary so that the left & right driveshafts appear to be level.
Front Camber:
Camber describes the angle at which the tire and wheel rides when looked at from the front. Negative camber means that the tire leans inward at the top. A good starting camber setting is -1°. Use the included #1719 camber gauge to set your camber. Positive camber, where the top of the tire is leaning out, is not recommended.
*Testing camber with camber gauge
!
*Raise or lower the ball end by
adding or subtracting
washers here
*Spacers to the rear will place hubs for-ward, shortening the wheelbase
*Front arms should be in a straight line when ride height is set at “arms level”
*CVA bones should be in a straight line when ride height is set at “CVA bones
level”
!
!
!
!
*Spacers to the rear
20:: Shocks
:: Shock Springs
:: Ball Differential
:: Shock Oil
177741875407629931327315109129991301913039130491305913069130891309913109131491316
4 ea.12812
2 ea.6222211
4 ea.1
4 ea.22
913259132691327913289132991330913319133291333913349133591336913379133891339913409134191342913439134491345
Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.11111
5420542154225423542454255426542754285429543054315432543354345435543654375438
2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.
65736574657565816582658976647666767798529853
261
121212111
FT Blue Aluminum Shock Pivot Ball with Eyelet.030 Nylon WasherRed O-RingsE-ClipVCS3 Shock Bottom Cap and O-RingM2 x 4mm BHCS12X23mm FT Shock Bodies (front)12X31mm FT Shock Bodies (rear)12MM Shock Cap12MM Threaded Collar and O-Ring21X3mm TiN Shock Shaft (front)27.5X3mm TiN Shock Shaft (rear)12MM Shock Pistons, (1.5, 1.6, 1.7)12MM Shock Rebuild Kit12MM Shock Spring Cups (+0mm, +5mm, +9mm)12MM Shock (B4/B44 Front)12MM Shock (B4/B44 Rear)
12MM Front SPRING BRN 2.8512MM Front SPRING BLK 3.00 - Kit12MM Front SPRING GRN 3.1512MM Front SPRING WHT 3.3012MM Front SPRING GRY 3.4512MM Front SPRING BLU 3.6012MM Front SPRING YLW 3.7512MM Front SPRING RED 3.9012MM Front SPRING ORN 4.0512MM Front SPRING PRL 4.2012MM Rear SPRING BLK 1.9012MM Rear SPRING GRN 2.0012MM Rear SPRING WHT 2.10 - Kit12MM Rear SPRING GRY 2.2012MM Rear SPRING BLU 2.3012MM Rear SPRING YLW 2.4012mm Big Bore Front Soft Spring Kit12mm Big Bore Front Medium Spring Kit12mm Big Bore Front Hard Spring Kit12mm Big Bore Rear Soft Spring Kit12mm Big Bore Rear Medium Spring Kit
10 Weight Silicone Shock Oil20 Weight Silicone Shock Oil30 Weight Silicone Shock Oil40 Weight Silicone Shock Oil22.5 Weight Silicone Shock Oil80 Weight Silicone Shock Oil27.5 Weight Silicone Shock Oil15 Weight Silicone Shock Oil25 Weight Silicone Shock Oil35 Weight Silicone Shock Oil45 Weight Silicone Shock Oil55 Weight Silicone Shock Oil32.5 Weight Silicone Shock Oil37.5 Weight Silicone Shock Oil42.5 Weight Silicone Shock Oil50 Weight Silicone Shock Oil60 Weight Silicone Shock Oil70 Weight Silicone Shock Oil47.5 Weight Silicone Shock Oil
Diff Thrust Washer & BoltPrecision Diff Thrust Balls, 5/64”Locking T-Nut, Diff Thrust Bolt, & Cover3/32” Carbide Diff BallsDiff Thrust SpringBall Bearing, 5/32 x 5/16” unflangedDiff Gear 52TDiff Drive Rings, 2.60:1B4 / T4 / GT Diff Rebuild KitSC10 Ball Diff OutdrivesSC10 Complete Ball Differential
6299
6299
91304
91304
91310
31327
31327
5407
5407
91303
91309
91309
91309
31510
9130591306
9129991301
4187
1777
1777
91308
6575
9853
6582
9852
7666
6589
6581
7664
6589
7666
9852
6573
6573
6574
6575
6575
21:: Slipper Clutch
:: Optional Gear Differential
:: Differential Fluids
6285662974617485748696039649965096519652965397399117591176911779117891179
126121211111111211
982798289829983098319888
5450545154525453545454555456545754585459
111
Pr.12
1111111111
Complete Gear DiffDiff Gear and Cover SetGear Diff Rebuild KitGear Diff OutdrivesGear Diff O-Ring Set0.5mm Gear Diff Shim
Silicone Diff Fluid 1,000CSTSilicone Diff Fluid 2,000CSTSilicone Diff Fluid 3,000CSTSilicone Diff Fluid 5,000CSTSilicone Diff Fluid 7,000CSTSilicone Diff Fluid 10,000CSTSilicone Diff Fluid 20,000CSTSilicone Diff Fluid 30,000CSTSilicone Diff Fluid 60,000CSTSilicone Diff Fluid 100,000CST
4-40 x 1/4” SHCS5-40 Diff Locking NutMolded Gear Cover, ClearFT V2 Slipper HubsFT V2 Slipper Spring and WasherSlipper Pad72T 48P Spur Gear75T 48P Spur Gear81T 48P Spur Gear (Kit)78T 48P Spur Gear84T 48P Spur GearSlipper SpringFT VTS Slipper ConversionVTS Slipper HousingVTS Slipper PadsVTS Slipper PlateFT VTS Slipper Hub, outer
7486
97396629
7485
7461
6285 6285
7461
91179
91176
91177
91177
91178
9603
9651
:: Turnbuckles and Servo Mounts1406177939816272629269177230733673379170918089007
226
2866
1214111
FT Blue Titanium Turnbuckles, 2.00”FT Servo Mount, blueBallstud .20” Black, shortFoam Ballend Dust Covers4-40 x 3/8” FHCS4-40 x 3/8” BHCSBallups, LargeSteering Servo Mount Kit.250 x .125 x .015” WasherSteering Servo LinkServo Horns, MoldedSteering Servo Ring, blue
91709180
1779
17796292
6917
6917
6917
6917
73367337
7337
7336
6292
39816272
9170
9170
89007
9830
9828
9828
9828
9828
9888
9829
9829
9888
9829
9829
7230
1406
9829
9829
9831
9831
9831
9831
9831
9830
9830
9830
:: Front Bulkhead / Steering
:: Front Shock Tower
:: Rear Shock Tower
39713981627262766332691769226929956696409659
967989229
17806272627764726924956831286
91311
4284461
4ea
6
178163326472691574139572958796439644
464661166
FT Shock Bushing, standard (blue)Foam Ballend Dust CoversBallstud .30 Silver (short)4-40/5-40 Plastic Nut4-40 x 3/8” SHCSB4 Front Shock TowerFT Ballstud Washer, aluminum(1mm, 2mm)4-40 x 7/8 BHCS
FT Shock Bushings, short, (blue)Body Clips4-40/5-40 Plastic Nut4-40 x 5/8” FHCS4-40 x 3/4 BHCSB4 Rear Shock TowerB4 / T4 Wing Mount / Shim Set5-40 x 7/16” SHCS 5-40 x 9/16” SHCS
.125 x .250 x .109“ BearingsBallstud .20 Black, shortFoam Ball end Dust CoversBallstud .20” Silver (short)Body Clip, Large4-40 X 3/8” BHCS4-40 x 1/2” FHCS4-40 x 3/8” SHCS w/holeB4 / T4 Top PlateB4 / T4 Steering Bolt, left & rightB4 / T4 Steering Set. Includes Rack,Bellcrank, Servo Saver, Steering BraceB4/T4 Aluminum Bellcrank SetBlue Countersunk Washers
22
9566
69226922
6922
89229
6332
6332
6332
6332
6929 6272
6272
91311
913119568
6277
6277
31286
31286
6924
6924
6924
6924
1780
1780
1781
1781
6472
6472
6472
6472
9587
95879587
9587
9572
9643
9643
9644
9644
7413
6915
6915
7413
6272
6272
6272
9640
9640
9659
3971
3971
3971 3971
6276
9679
9679
9659
3981
3981
9659
6917
6917
89229
89229
46
2866664111
110
23 :: Front Arm
:: Rear Arm
39773983444962726277692569537369749679229578962196229645988098829891
989831286
265
28466421
Pr.118
Pr.62
64ea
39773981627262886925695273687369738179337935958296229630964596729677975598649890
989899173123731286
26
28666
144122
Pr.1
10821222
622
4ea
Ball Bearing 3/16” x 3/8”Ballstud .30” Black (short)4-40 x 3/16 Aluminum LocknutFoam Ballend Dust CoversBallstud .30 Silver (short)4-40 X 1/2” SHCS8-32 Low Profile Locknut, steel1/16” Universal Roll PinsB4 Front Axle, hexCaster Block, (left & right) 30 degFront A-Arm B4Inner Hinge Pin SetOuter Hinge Pin Set2-56 x 1/8” BHCSSteering Block, Hex C-Clip, 3/16”12mm Aluminum Clamping Wheel Hex, Buggy Front2-56 x 3/16 SHCSFT Ballstud Washer, aluminum(1mm, 2mm)
Ball Bearing 3/16 x 3/8”Ballstud .20” Black (short)Foam Ballend Dust Cover4-40 X 1/4” BHCS4-40 x 1/2” SHCS8-32 Locking Nut, Steel3/16” Axle Shims1/16” Axle Roll PinsCVD Rebuild KitAxle Spacer Crush TubesBearing, .187 x .50 x .196B4 Rear A-Arms (left & right)B4 Outer Hinge Pin SetBallstud Washer2-56 x 1/8” BHCSFT CVA Bone, B4FT CVA Set, B4CVA Axle, RearFT Aluminum Hub, 0.0 deg12mm Aluminum Clamping Wheel Hex, Buggy Rear2-56 x 3/16 SHCSFT Aluminum Hub A, carbonCVA Pin Retaining ClipAluminum Ballstud Washer(1mm & 2mm)
79227922
9622
9622
9622
9621
9645
9645
9645
9645
6925
6925
9582
9578
7496
9882
6272
6272
6272
3981
6277
31286
9880
31286
3977 3977
3977
96306288
9917
7933
7935 7369
6952
9890
9898
9864
6953
9898
9891
7369
3983
4449
4449
4449
97557368
7381
7381
9672
31237
24:: Battery Strap
:: Transmission
178792389638
111
1770397769136919692269246925692869369360936195759601960296309826983231532
12666666101111110126
FT Battery Strap Thumbscrews SetFoam Battery Spacers, SetBattery Strap B4, Carbon Fiber
FT Milled Motor Plate, blueBall Bearing, 3/16” x 3/8“4-40 x 1 1/4” SHCS4-40 X 5/16” BHCS4-40 X 1/2” FHCS4-40 X 3/8” SHCS4-40 x 1/2” SHCS4-40 x 1” SHCS#4 Washer, aluminumIdler Gear, moldedIdler Gear ShaftRear Motor GuardB4/T4 Top ShaftB4/T4 Top Shaft SpacerBallstud WasherTransmission Case for Gear Diff (left & right)Ball Bearing, 10 x 16mmM3 x 8mm BHCS
:: Pinion Gears8253825482558256825782588259826082618263826482658266826782688269827082718272
1111111111111111111
16T 48P Pinion Gear17T 48P Pinion Gear18T 48P Pinion Gear19T 48P Pinion Gear20T 48P Pinion Gear21T 48P Pinion Gear22T 48P Pinion Gear23T 48P Pinion Gear24T 48P Pinion Gear 26T 48P Pinion Gear27T 48P Pinion Gear28T 48P Pinion Gear29T 48P Pinion Gear30T 48P Pinion Gear31T 48P Pinion Gear32T 48P Pinion Gear33T 48P Pinion Gear34T 48P Pinion Gear35T 48P Pinion Gear
1787
1787
1787
1787
9638
9238
69196919
9575
69226922
6924
9832
9832
9361
9602
9601
9360
3977
39779826
9826
6925 6928
6928
6913
9630
9630
9630
1770
6924
31532
31532 6936
6936
9238
25:: Chassis
38624334627262776338691574877488926995629563956496219637964396459665981831286
68
28416116111416811
4ea
5-40 x 1/8” Set Screw2-56 x 5/16” BHCSFoam Ballend Dust CoverBallstud .30” Silver (long)Antenna Tube & Cap (black)4-40 X 5/8” FHCSArm Mounts 2.5, 3, 3.5, 4 deg SetBallast Weight5-40 x 1/2” FHCSFront BumperB4 / T4 / GT2 Front BulkheadRR / FR Hinge BraceB4 Inner Hinge Pin SetB4 +8mm Chassis5-40 x 7/16” SHCS 2-56 x 1/8” BHCSFT Hinge Pin Brace, blueB4/T4/SC10 Arm Mount / Chassis PlateAluminum Ballstud Washer(1mm & 2mm)
:: Wheels9690969196959696
2222
Buggy Front Wheel, hex, whiteBuggy Front Wheel, hex, yellowBuggy Rear Wheel Hex, whiteBuggy Rear Wheel Hex, yellow
3862
6338
9818
9645
9621
9621
7487
7487
7488
9269 9269
9637
69156915
6915
6915
9562
9563
4334
9665
6272
6272
9564
31286
6277
6277
31286
9643
9643
96969691
Not includedin Kit!
Not includedin Kit!
26:: Factory Team and Option Parts140614091585165417341735173617701777177817791780178117873971690669376943738174857486748779227990956195659567956995739577957995839586959295939594959795989599
9600B96239635
9655966596729673967796799739975597899795979697979798979998649865986698679872991731237312869117591176911779117891179
Pr.Pr.Pr.41046141
Pr.44
Pr.42661
Pr.11
Pr.111111
Pr.Pr.Pr.1
Pr.Pr.1
Pr.Pr.11
Pr.1
11
Pr.Pr.Pr.11
Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.1
Pr.Pr.
4ea.11211
FT Ti Turnbuckle, 2.00” (blue)FT Ti Turnbuckle, 1” (sway bar) (blue)FT B4 Aluminum Trailing AxleFT Solid Axle PinsFT Blue Body Clip, 4 long, 6 shortFT Blue Body Clip, longFT Blue Body Clip, shortFT Milled Aluminum Motor Plate, (blue)Blue Aluminum Shock Ball Ends with EyeletsFT Milled Aluminum Motor Plate, (black)FT Servo Mounts, blue aluminumFT Blue Alum. Threaded Shock Bushings (standard)FT Blue Alum. Threaded Shock Bushings (short)FT Battery Strap Thumb ScrewsSteering Rack BearingsBall Bearing, PTFE Sealed 3/16 x 3/8”FT 4-40 Aluminum Locknuts (blue)FT 8-32 Aluminum Locknuts (blue)CVD Rebuild KitFT V2 Slipper HubsFT V2 Slipper Spring and WasherArm Mount Set (2.5, 3, 3.5, 4 deg)Caster Block 30 deg, (left & right)Aluminum Front BulkheadB4 Chassis Carbon, short chassisChassis Brace, Hinge Pin Brace, CarbonTop Plate, CarbonFront Shock Tower B4 CarbonRear Shock Tower Carbon B4Steering Blocks, Inline (B4 req. #9623)Front A-Arm B4 CarbonRear A-Arm B4 CarbonBattery Strap Carbon, B4 (short chassis)Caster Block 20 deg, (left & right)FT Caster Block, 30 deg, (left & right)Battery Strap Woven Carbon, B4 (short chassis)CVD Axle Bones, B4CVD Axles, B4 / T4CVD Set, B4FT Aluminum Motor Plate (blue)FT B4 Front Inline Axle (req. #9577)B4 / T4 Sway Bar Kit. Includes color coded bars,soft (black), med (silver), hard (gold)B4 Full Carbon Set, (short chassis)FT B4 / T4 Aluminum Hinge Pin BraceFT CVA Bone, B4B4 Shiny CVD DogboneFT CVA Set, B4B4/T4 Aluminum Bellcrank SetSlipper SpringCVA Axle, Rear (B44, B4, T4, SC10)FT Titanium Front Axles, SC10 / B4Ti Nitride Ballstuds 4-40 x 0.20” LongTi Nitride Ballstuds 4-40 x 0.30” LongTi Nitride Ballstuds 4-40 x 0.40” LongTi Nitride Ballstuds 4-40 x 0.20” ShortTi Nitride Ballstuds 4-40 x 0.30” ShortFT Aluminum Hub, 0 degFT Aluminum Hub, 0.5 degFT Aluminum Hub, 1 degFT Aluminum Hub, 1.5 degFT Aluminum Hub Tower SetAluminum Hub A, CarbonCVA Pin Retaining ClipFT Ballstud Washer, aluminum (1mm, 2mm)FT VTS Slipper ConversionVTS Slipper HousingVTS Slipper PadsVTS Slipper PlateFT VTS Slipper Hub, outer
:: Body and Decals
:: XP Electronics
:: Reedy Accessories
9614965896759676969297729790979197929782
291072912529126291412914229143291662916729209292102921129212292142921529216292172921829221
1111111111
111111111111111111
604605606607654655656658659660661663664716959960961962972973974975978979980981982992
1111111111111111111111111111
B4 Clear Body & WingB4 Decal SheetB4 Painted Body, Flames, Blue BackgrouondB4 Painted Body, Flames, Red BackgroundB4 Vortex Body + Wings Set, clearHigh Downforce Wing 6.5”B4.1 RTR Body, Blue, with spoiler (Kit, B4.1)B4.1 RTR Body, Green, with spoiler (Kit, B4.1)B4.1 Body Clear, with spoilerB4.2 Decal Sheet
S1903 Metal Gear SetS1903MG ServoS2008MG ServoXP SC450-BL Brushless ESCXP ESC Fan OptionXP SC700-BL Brushless ESCXP DS1313 Digital ServoXP DS1015 Digital ServoGear Set, DS1313Gear Set, DS1015Servo Case , DS1313 / DS1015Accessory Pack, DS1313 / DS1015TRS 403-SSi ReceiverXP2G 2.4GHz Radio SystemXP3G 2.4GHz Radio SystemXP TRS402-SSI ReceiverXP2-SSi 2.4GHz Radio SystemXP3SS 2.4GHz Radio System
526-S AC/DC 2S-6S LiPo/LiFe ChargerMotor Cooling Fans (2)Charge Harness 2S Saddle Pack 4mmCharge Harness 2S Standard Pack 4mm4.0mm plugs (2M, 2F) 4.0mm plugs (2M, 10F) 4.0mm plugs (10F)4.0mm plugs (10M)4.0mm plugs (30M)3.5mm plugs (3M, 3F)3.5mm plugs (10F)3.5mm plugs (10M)3.5mm plugs (30M)Reedy 09 Decal SetSonic 540/550 Sensor w/BearingSonic 540/550 Insulator Set (2 pcs.)Sonic 540/550 Timing Cap w/ScrewsSonic 540 Case Screws (3 pcs.)Sonic 540 Steel Bearing SetSonic 540 Ceramic Bearing Set540-SL/550-SL Steel Bearing Set540-SL/550-SL Ceramic Bearing SetFlat Sensor Wire 70mmFlat Sensor Wire 110mmFlat Sensor Wire 150mmFlat Sensor Wire 200mmFlat Sensor Wire 270mmSonic 540 Rotor Spacers
:: Reedy Motors and ESC’s
:: Reedy Batteries
908920921922923940941941S942943944945946947948949950951952954955956957958987
1111111111111111111111111
302303309601602628632633634637736738
111111111111
Replacement Rotor 540-SL540-SL Brushless Motor 3300kV540-SL Brushless Motor 3900kV540-SL Brushless Motor 4900kV540-SL Brushless Motor 6100kVSonic 540 21.5 Competition Brushless MotorSonic 540 17.5 Competition Brushless MotorSonic 540 17.5 Replacement StatorSonic 540 13.5 Competition Brushless MotorSonic 540 10.5 Competition Brushless MotorSonic 540 9.5 Competition Brushless MotorSonic 540 8.5 Competition Brushless MotorSonic 540 7.5 Competition Brushless MotorSonic 540 6.5 Competition Brushless MotorSonic 540 5.5 Competition Brushless MotorSonic 540 5.0 Competition Brushless MotorSonic 540 4.5 Competition Brushless MotorSonic 540 4.0 Competition Brushless MotorSonic 540 3.5 Competition Brushless MotorSonic 540 Stock Rotor 12.3 x 24.2 (7.25)Sonic 540 Stock Rotor 12.3 x 25.0 (7.25)Sonic 540 Stock Rotor 12.5 x 25.0 (7.25)Sonic 540 Modified Rotor 12.2 x 25.0 (5.0)Sonic 540 Modified Rotor 12.5 x 25.0 (5.0)Sonic 540 Modified Rotor 13.0 x 25.3 (5.0)
AA Alkaline 1.5V (4)AA 2700mAh NiMH 1.2V Rechargeable 7000mAh 65C 7.4v LiPo6500mAh 65C Competition 7.4V LiPo4100mAh 65C Competition 7.4V Shorty LiPo5500mAh 7.4V 60C LiPoTX Lightweight Battery 1350mAh 11.1VTX Battery - 3PK, M11 3000mAh 11.1VTX Battery - Helios, Z1 2400mAh 11.1VTX Battery - M11X 2500mAh 7.4VWolfPack 5000mAh 25C 7.4V LiPoWolfPack 3800mAh Shorty 7.4V 25C
27
:: LRP Speed ControlsLRP80230LRP80250LRP80970
111
Spin Super BrushlessSpin Pro BrushlessFlow Works Team
:: LRP Chargers, Power Supply, BalancerLRP41281LRP41555LRP42103LRP42104LRP42105LRP42305LRP42306LRP43200LRP45050LRP45200LRP65800LRP65802LRP65803LRP65804LRP81801
111111111111111
Quadra Pro 2 ChargerPulsar Touch Competition ChargerLiPo Balance Board XHLiPo Balance Board FP/TP LiPo Balance Board PQPulsar Touch Temperature SensorPulsar Touch Sensor Wire SplitterLRP Competition 20A Power SupplyLRP 2in1 LiPo Guard + BECLiPo Parallel BalancerHigh Power Solder StationSoldering Tip 5mmSoldering Tip 1.2mmSoldering HandleLRP Speedo Updater Spec 2
:: LRP Brushless Motors / CombosLRP50430LRP50440LRP50450LRP50460LRP50480LRP50643LRP50644LRP50654LRP50664LRP50674LRP50684LRP50689LRP50694LRP50704LRP80741LRP80742LRP80743
11111111111111111
Vector K4 6.5 TurnVector K4 8.5 TurnVector K4 10.5 TurnVector K4 13.5 TurnVector K4 17.5 TurnVector X-20 10.5 TurnVector X-20 9.5 TurnVector X-20 8.5 TurnVector X-20 7.5 TurnVector X-20 6.5 TurnVector X-20 5.5 TurnVector X-20 5.0 TurnVector X-20 4.5 TurnVector X-20 4.0 TurnSpin Super / K4 17.5 Turn Spin Super / K4 13.5 TurnSpin Super / K4 10.5 Turn
:: LRP Misc.LRP50621LRP50622LRP50623 LRP50626LRP50632 LRP50634LRP50635LRP50636LRP50637LRP50638LRP50639LRP62415LRP80135LRP82512LRP82515LRP82520LRP82530LRP82531LRP819307LRP819310LRP819315LRP819320
1111111111111111111111
X-12 Optional Ceramic Ball BearingsX-12 Small Parts Set X-12 PreciSensor Unit X-12 Alum Rear Cover X-12 12.0mm Sintered RotorX-12 13.0mm Sintered RotorX-12 Stock Spec Rotor 12.45mmWorks Team X-12 12.0mm RotorWorks Team X-12 12.5mm RotorWorks Team X-12 13.0mm RotorX-12 Stock Spec 1S LiPo RotorLRP Logo Sticker SheetBEC Stabilizing Capacitor SXX Low Profile Fan 30mm Motor Fan/Clamp, GunmetalRadical Cooling Set, Blue SXX Power Cap 3.7-4.8V SXX Power Cap 6.0-7.4V70mm High Flex Sensor Wire100mm High Flex Sensor Wire150mm High Flex Sensor Wire200mm High Flex Sensor Wire
:: Lubes & Adhesives / Decals / Misc.1105159615976588659166366727
716717381638203834
1111112
11112
FT Green Slime Shock LubeFT Locking AdhesiveFT Tire Adhesive, mediumBlack Grease - 4ccS.Diff Lube - 4ccSilicone Grease - 4ccServo Tape
Reedy 2009 Sticker SetReedy Powered Logo DecalAmerican Bumper StickerAE Logo Decal SheetAE Blue Embossed Logo Sticker
28:: Tools111114501541154215431544154515461547154815511553155415611562156315641565156715891590159216551656165716581659166016611662166316641665166616671668166916701671167216731674
1719173737183719372039876429695674947709
111111111111111111111111111111111111111111
11
1212121111
12
FT Turnbuckle WrenchFT Ride Height GaugeFT Hex Driver Set, (7 pcs)FT .050” Silver Hex DriverFT 1/16” Black Hex DriverFT 1.5mm Purple Hex DriverFT 5/64” Blue Hex DriverFT 3/32” Gold Hex DriverFT 2.5mm Green Hex DriverFT 3mm Red Hex DriverFT Screwdriver SetFT Phillips Silver ScrewdriverFT Silver Spring Hook Tool FT Nut Driver Set, (6 pcs)FT 3/16” Black Nut DriverFT 1/4” Red Nut DriverFT 5.5mm Red Nut DriverFT 11/32” Green Nut DriverFT 8mm Gold Nut DriverFT 5/64” Blue Ball Hex DriverFT 3/32” Gold Ball Hex DriverFT Ball Hex Driver Set, (3 pcs)FT 8-Piece 1/4” Hex Drive SetFT 1/4” Hex Drive Handle, without tipsFT 1/4” Hex Drive .050” TipFT 1/4” Hex Drive 1/16” TipFT 1/4” Hex Drive 5/64” - 2.0mm TipFT 1/4” Hex Drive 3/32” TipFT 1/4” Hex Drive 1.5mm TipFT 1/4” Hex Drive 2.5mm TipFT 1/4” Hex Drive 3/16” Nut Driver TipFT 1/4” Hex Drive 1/4” Nut Driver TipFT 1/4” Hex Drive 11/32” Nut Driver TipFT 1/4” Hex Drive 5.5mm Nut Driver TipFT 1/4” Hex Drive 7.0mm Nut Driver TipFT 1/4” Hex Drive 8.0mm Nut Driver TipFT 1/4” Hex Drive 5/64” - 2.0mm Ball End TipFT 1/4” Hex Drive 3/32” Ball End TipFT 1/4” Hex Drive Standard Screwdriver TipFT 1/4” Hex Drive Phillips Screwdriver TipFT 1/4” Hex Drive 2.5mm Ball End TipFT 1/4” 5 Piece Power Tool Tips Set (5/64-2.0mm, 1.5mm, 2.5mm, 5/64”- 2.0mm ball, 2.5mm ball)FT Camber + Track Width ToolFT Body Scissors12 Inch Nylon Wire Ties6 Inch Nylon Wire Ties8 Inch Nylon Wire TiesFT Droop GaugeShock Building ToolMolded Tools, SetV2 Stamped Multi-tool4 Inch Nylon Wire Ties
:: 1/18 Kits and RTR’s
:: 1/12, 1/10 Kits and RTR’s
201032011020115201182012120130
204240207023702970307034703770467047704870497050705270927093802080229039904090419050906230101301089000490005900069000790010
111111
11111111111111111111111111111
RC18B2 - RC18T2 Team KitRC18MT RTR (ready-to-run)RC18R Kamino RTR (ready-to-run)RC18R Niteline RTR (ready-to-run)SC18 RTR Brushless (ready-to-run)RC18LM RTR (ready-to-run)
Nitro TC3 RTR Plus (ready-to-run)FT 12R5.2 KitRC10T4.1 FT KitSC10 Associated/RC10.com Truck RTR (ready-to-run)SC10 KMC Wheels Race Truck RTR (ready-to-run)SC10 FT KitRC10T4.1 RTR 2.4GHz Brushless (ready-to-run)SC10 RS RTR, Lucas Oil (ready-to-run)SC10 RS RTR, Monster Energy (ready-to-run)SC10 RS RTR, Pro Comp (ready-to-run)SC10 RS RTR, Rockstar/Makita (ready-to-run)SC10 RS RTR, Hart and Huntington (ready-to-run)Quaifier Series - Pro Lite 4x4 RTR (ready-to-run)GT2 RS Truck Nitro RTR (ready-to-run)SC10GT RTR (ready-to-run)FT RC10R5 KitFT RC10R5.1 KitRC10B4.1 RTR 2.4GHz Brushless (ready-to-run)FT RC10B4.1 Worlds KitFT RC10B4.2 KitSC10B RS RTR (ready-to-run)FT B44.2 4WD Buggy KitTC4 Club Racer 4WD Touring Car Race RollerFT TC6.1 WC 4WD Touring Car KitSC10 4x4 KitSC10 4x4 Lucas Oil RTR (ready-to-run)SC10 4x4 Pro Comp RTR (ready-to-run)SC10 4x4 Rockstar/Makita RTR (ready-to-run)SC10 4x4 FT Kit
:: 1/8 Kits and RTR’s205012050220503
20504
8090580906809078090880912
80933
80934
111
1
11111
1
1
MGT 4.60 SE RTR (ready-to-run)MGT 8.0 Nitro RTR (ready-to-run)Limited Edition MGT 4.60 Nitro RTR, w/flag body (ready-to-run)Limited Edition MGT 8.0 Nitro RTR, w/flag body (ready-to-run)RC8RS “Race Spec” Nitro Buggy RTR (ready-to-run)RC8.2 Nitro Buggy FT KitRC8.2e Electric Buggy FT KitRC8.2e Electric Buggy RTR (ready-to-run)RC8T Championship EditionRC8T-RS “Race Spec” Nitro Truggy RTR (ready-to-run)SC8.2e Short Course Race Truck, Rockstar/Makita Electric RTR (ready-to-run)SC8.2e Short Course Race Truck, Slick Mist ElectricRTR (ready-to-run)
29
:: ApparelSP35**SP36**SP37**SP38SP39
SP66**SP67**SP68**SP69**
SP70**SP71**SP73**SP74**SP75**SP76**SP77**SP78**SP79**SP411SSP411LSP413SSP413LSP417SP418
SP420**SP421SSP421LSP422SSP422LSP423SSP423LSP424SSP424L
715110684
111111111
111111111111111
Pr.1111111111
Reedy 09’ White T-Shirt (L, XL, 2XL)Reedy 09’ Black T-Shirt (M, L, XL, 2XL, 3XL)Reedy 2012 T-shirt - Black (S, M, L, XL, 2XL, 3XL)Reedy Trucker HatReedy PatchStencil Blue T-Shirt (S, M, L, XL, 2-6XL)AE Stencil Gray Sweatshirt (S, M, L, XL, 2XL, 3XL)AE Stencil Blue T-Shirt (M, L, XL, 2XL)AE 26 Time World Championship T-Shirt, Black (S, M, L, XL, 2XL, 3XL)Associated Windbreaker (S, M, L, XL, 3XL)Associated Winter Jacket (S, M, L, XL, 2XL)AE Long Sleeve T-Shirt (S, M, L, XL, 2XL)AE White T-Shirt (S, M, L, XL, 2XL, 3XL, 4XL)AE Blue T-Shirt (S, M, L, XL, 2-6XL)AE Black T-Shirt (S, M, L, XL, 2XL, 3XL, 4XL) AE 2012 T-Shirt, Blue (S, M, L, XL, 2XL, 3XL)AE 2012 T-Shirt, White (S, M, L, XL, 2XL, 3XL)AE 2012 T-Shirt, Black (S, M, L, XL, 2XL, 3XL)AE Hat 11’ Flat Bill Black S/MAE Hat 11’ Flat Bill Black L/XL26 Time World Championship Hat S/M26 Time World Championship Hat L/XL1/10 FT Motor BagFactory Team 1/10 Car Carrier BagAE Pit Gloves (M, L, XL)AE 2012 Hat, Black, Flat Bill, S/MAE 2012 Hat, Black, Flat Bill, L/XLAE 2012 Hat, Black, Curved Bill, S/MAE 2012 Hat, Black, Curved Bill, L/XLAE 2012 Hat, White, Flat Bill, S/MAE 2012 Hat, White, Flat Bill, L/XLAE 2012 Hat, White, Curved Bill, S/MAE 2012 Hat, White, Curved Bill, L/XLReedy 2009 Track BannerTeam Associated Track Banner
** Use part number plus the desired size when ordering!
:: Contact Information
Associated Electrics, Inc.26021 Commercentre Drive
Lake Forest, CA 92630-8853 USAhttp://www.TeamAssociated.com
http://www.RC10.comhttp://twitter/Team Associated
http://bit.ly/AEonFacebook
call: (949) 544-7500fax: (949) 544-7501
Check out the following web sites for all of our electric kits, current products, new releases, setup help, tips, and racing info!
www.TeamAssociated.com. - www.RC10.com
30:: Notes
Ride Height:
I O
A CB
Driver: Date: Track: Event:Conditions: Indoor Outdoor Temp. Rev.1Setup Sheet
:: For more setups, visit RC10.com and click on “Setup Sheets”
Front Suspension
Front Shocks
Electronics / Weight
DifferentialsDrivetrain
Front Tires
Race and Vehicle Comments
Other
Rear Tires
Track Info
Rear Suspension
Rear Shocks
Anti Roll Bar:
NoneBlack (soft)Silver (med)Gold (hard)
Rear Hub Carriers:0°0.5°1°1.5°
Spring: Piston:Shock Oil: Limiter:
Motor & Wind:Pinion: Spur Gear:Batteries:Battery Placement:Ballast Weight: Chassis Weight:
Slipper:2 Pads 3 Pads 4 PadsNotes:
Ball:Gear:Notes:
Tire:Compound:Insert: Wheel:
Qualify: Main: Finish: TQ:Comments:
Tire:Compound:Insert: Wheel:
Surface:DirtCarpetAstroMulti
Traction:LowMedHigh
Moisture:WetDampDry
Conditions:GroovedDustySmoothBumpyHard PackLoamy
Radio:Throttle / Brake e.p.a:Throttle / Brake expo:Servo: Steering Expo:ESC: ESC Settings:
Body Type:Wing Type: Wing Angle:
Spring: Piston:Shock Oil: Limiter:
Washers:
Washers:
Washers:
Ride Height:
Aluminum Hub Tower:ABC
Caster Block Spacing:ForwardBack
Caster:
20°25°30°
1 2 3
1
1
2
2
I O
A CB D
Camber:
Inner Toe:
Anti-Squat:
Camber:
Toe:12 3 -1 -1
0 3°
2°
2mm1mm
2mm
Black
30wt
Thin pad back, thick pad front
Proline VortexVortex
30wt3
VTS
Stock Stock
2
White1.6 1.6
24mm
24mm
Wheelbase:LongMediumShort
Chassis BraceGround Flat:
Steering Rack:
FrontBack
32:: Hardware - 1:1 Scale View
Notes:
E-clip 1/8 (6299)
Clips
2-56x1/8 (9645)
2-56x5/16 (4334)
4-40x5/16 (6919)
4-40x3/8 (6917)
4-40x7/16 (2221)
4-40x3/4 (7413)
4-40x7/8 (91311)
3x8mm (31532)
Button Head (bhcs)
4-40 Aluminum Locknut (4449)
4-40 Plastic Nut (6472)
5-40 Diff Locknut (6629)
8-32 LP Steel Locknut (6953)
8-32 Steel Locknut (6952)
Nuts (lock/plain)
5/64 Diff Thrust Balls (6574)
3/32 Carbide Diff Balls (6581)
Diff Balls
Ballstuds
Black .20 Short (3981)
Black .30 Short (3983)
Silver .20 Short (6276)
Silver .30 Long (6277)
Silver .40 (6278)
.030 Ballstud Washer (9630)
.030 Nylon Spacer (4187)
Servo Mount Washer (7337)
#4 Washer (6936)
3/16 Axle Shim - Silver (7368)
FT Ballstud Washer, Aluminum(1mm and 2mm, 4 each) (31286)
Shims and Washers
4-40x3/8 (6292)
4-40x1/2 (6922)
4-40x5/8 (6915)
5-40x1/2 (9269)
Flat Head (fhcs)
Ball Bearings
Steering Rack Bearing (3971)
3/16x3/8 (3977)
3/16x1/2 RS (7935)
10 x 16mm (9832)
Cap Head (shcs)
2-56x 3/16 (9898)
4-40x1/4 (6285)
4-40x5/16” (6932)(4145, aluminum)
4-40x3/8 (6924)w/hole (6929)
4-40x1/2 (6925)
4-40x5/8 (6926)
4-40x3/4 (6927)
4-40x7/8 (7738)
4-40x1 (6928)
4-40x1 1/4 (6913)
4-40x1 3/4 (9833)
5-40x7/16 (9643)
5-40x9/16 (9644)
5-40x7/3/4 (9835)
Ride Height:
I O
A CB
Driver: Date: Track: Event:Conditions: Indoor Outdoor Temp. Rev.1Setup Sheet
:: For more setups, visit RC10.com and click on “Setup Sheets”
Front Suspension
Front Shocks
Electronics / Weight
DifferentialsDrivetrain
Front Tires
Race and Vehicle Comments
Other
Rear Tires
Track Info
Rear Suspension
Rear Shocks
Anti Roll Bar:
NoneBlack (soft)Silver (med)Gold (hard)
Rear Hub Carriers:0°0.5°1°1.5°
Spring: Piston:Shock Oil: Limiter:
Motor & Wind:Pinion: Spur Gear:Batteries:Battery Placement:Ballast Weight: Chassis Weight:
Slipper:2 Pads 3 Pads 4 PadsNotes:
Ball:Gear:Notes:
Tire:Compound:Insert: Wheel:
Qualify: Main: Finish: TQ:Comments:
Tire:Compound:Insert: Wheel:
Surface:DirtCarpetAstroMulti
Traction:LowMedHigh
Moisture:WetDampDry
Conditions:GroovedDustySmoothBumpyHard PackLoamy
Radio:Throttle / Brake e.p.a:Throttle / Brake expo:Servo: Steering Expo:ESC: ESC Settings:
Body Type:Wing Type: Wing Angle:
Spring: Piston:Shock Oil: Limiter:
Washers:
Washers:
Washers:
Ride Height:
Aluminum Hub Tower:ABC
Caster Block Spacing:ForwardBack
Caster:
20°25°30°
1 2 3
1
1
2
2
I O
A CB D
Camber:
Inner Toe:
Anti-Squat:
Camber:
Toe:12 3
Wheelbase:LongMediumShort
Chassis BraceGround Flat:
Steering Rack:
FrontBack
Associated Electrics, Inc.26021 Com
mercentre Dr.
Lake Forest, CA 92630 USAhttp://w
ww
.TeamAssociated.com
http://ww
w.RC10.com
http://twitter/Team
_Associatedhttp://bit.ly/AEonFacebook
call: (949) 544-7500 - fax: (949) 544-7501Check out the follow
ing web sites for all of our kits,
current products, new releases, setup help, tips, and racing info!
ww
w.Team
Associated.com. - w
ww
.RC10.com