Assign 4
1
P O N 1 2 3 M L K I 4 5 6 7 8 H G F E D C B A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 P O N M K J I 9 10 11 12 13 H G F E D 14 15 16 C B A THIRD ANGLE PROJECTION 3. GENERAL FINISH REMOVE BURRS & LIGHTLY BREAK SHARP EDGES 4. DO NOT SCALE 1. ALL DIMENSIONS ARE IN MILLIMETRES (mm) NOTES: UNLESS OTHERWISE STATED TGB 21112012 INSERT MATERIAL SPECIFICATION HERE INSERT HEAT TREATMENT SPECIFICATION HERE Sample Component Drawn by Date 21112012 Drn. Tim Baker DRS Date RELEASED FOR INFORMATION & LAYOUT ONLY 00A Matl. Heat Treat. Surface Finish Title Issue Dwg. No. Ref. - RELEASED FOR MANUFACTURE 01A INSERT SURFACE FINISH SPECIFICATION HERE FS2013-00-0000-01A 2. THREADS: ISO COARSE TO CLASS 6H/6g U.O.S - FS2013-00-0000-01A Details L J - 21112012 ANGULAR ±1° GENERAL TOLERANCES: 0.00 ±0.05 0.0 ±0.2 0 ±0.5 LINEAR AND RADIAL 3 1:1 Scale Size A0 Sheet 1 of 1 Qty per Assembly 1 TGB 0000 THIS DRAWING AND THE COPYRIGHT THEREIN IS THE PROPERTY OF UCL RACING. IT MAY NOT BE COPIED, REPRODUCED, PUBLISHED OR DISCLOSED TO ANY OTHER PARTY, IN WHOLE OR IN PART, WITHOUT THE WRITTEN CONSENT OF AN AUTHORISED UCL RACING REPRESENTATIVE. Dep Univ Torr Lon WC +44 info www 50 50 85 REF. 30 = = A B B 114.5 REF. 129.12 REF. 126 PCD. 120 (X3) 10 R (X3) 31.5 REF. 54.56 REF. 32 LASER MARK WITH PART NUMBER AND DESCRIPTION HERE ON THIS FACE AKMAL BIN ABU BAKAR - 14059814 3 R TYP. 48.5 50 1 R TYP. 5 3.5 8.5 12 2 10 3 R TYP. 8.5 ±0.1 2 POS. 20 2 BOSSES Detail A Scale: 2:1 Ø0.2 A 10 18 CH'F x 90° 41.8 30 8.5 2 CH'F x 15° 31.975 31.950 (Ø32 f7) 1 R 2 CH'F x 15° 1.6 +0.15 0 0.5 R 37 +0.14 0 CIRCLIP GROOVE 35.025 35.000 (Ø35 H7) 1 CH'F x 15° Section view B-B Scale: 1:1 A Ra 1.6 Ra 1.6 C 1 CH'F x 15° 6 7.56 REF. 9 PTD. 1 R TYP. 12 6.012 6.000 (Ø6 H7) 1 R 5 Detail C Scale: 2:1 Ø0.05 A 6 Isometric view Scale: 1:1
-
Upload
akmal-bakar -
Category
Documents
-
view
213 -
download
1
description
technic drawing of bla bla
Transcript of Assign 4
-
PO
N
1 2 3
M
L
K
I
4 5 6 7 8
H
G
F
E
D
C
B
A
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
P
O
N
M
K
J
I
9 10 11 12 13
H
G
F
E
D
14 15 16
C
B
A
THIRD ANGLE PROJECTION
3. GENERAL FINISH REMOVE BURRS & LIGHTLY BREAK SHARP EDGES
4. DO NOT SCALE
1. ALL DIMENSIONS ARE IN MILLIMETRES (mm)
NOTES: UNLESS OTHERWISE STATED
TGB 21112012
INSERT MATERIAL SPECIFICATION HERE
INSERT HEAT TREATMENT SPECIFICATION HERE
Sample Component Drawn byDate21112012
Drn.
Tim Baker
DRS Date
RELEASED FOR INFORMATION & LAYOUT ONLY00A
Matl.
Heat Treat.
Surface Finish
Title
Issue
Dwg. No.
Ref.
-
RELEASED FOR MANUFACTURE01A
INSERT SURFACE FINISH SPECIFICATION HERE
FS2013-00-0000-01A
2. THREADS: ISO COARSE TO CLASS 6H/6g U.O.S
-
FS2013-00-0000-01A
Details
L
J
- 21112012
ANGULAR 1
GENERAL TOLERANCES:
0.00 0.050.0 0.20 0.5
LINEARANDRADIAL
3
1:1Scale Size A0 Sheet 1 of 1 Qty per Assembly 1
TGB 0000THIS DRAWING AND THE COPYRIGHT THEREIN ISTHE PROPERTY OF UCL RACING. IT MAY NOT BECOPIED, REPRODUCED, PUBLISHED OR DISCLOSEDTO ANY OTHER PARTY, IN WHOLE OR IN PART,WITHOUT THE WRITTEN CONSENT OF AN AUTHORISEDUCL RACING REPRESENTATIVE.
Department of Mechanical Engineering
University College London
Torrington Place
London
WC1E 7JE
+44 (0)20 7679 7178
www.mecheng.ucl.ac.uk
50
50
85 REF.
3 0= =
A
B
B
114.5 REF.
1 29.12 REF.
126 PCD.
120
(X3)
10R (X3)
31.5 REF.
5 4.56 REF.
32
LASER MARK WITH PART NUMBER ANDDESCRIPTION HERE ON THIS FACEAKMAL BIN ABU BAKAR - 14059814
3R TYP.
48.5
50
1R TYP.
5
3.5
8.5
12
210
3R TYP.
8.5 0.1
2 POS.
20
2 BOSSES
Detail AScale: 2:1
0.2 A
10
18CH'F x 90
41.8
30
8.5
2CH'F
x 15
3 1.97531.950 (32 f7)
1R
2CH'F x 15
1.6 +0.15 0
0.5R
37
+0.14
0
CIRCLIP GROOVE
35.025
35.000(35 H7)
1CH'F x 15
Section view B-BScale: 1:1
A
Ra
1.6
Ra1.6
C
1CH'F
x 15
67.56 REF.
9 PTD.
1R TYP.
12
6.0126.000 (6 H7)
1R
5
Detail CScale: 2:1
0.05 A
6
Isometric viewScale: 1:1
