ASSEMBLY INSTRUCTIONS Wallaby IIarrowcabinets.com/wp-content/pdf/WallabyII-Assembly-Manual.pdf ·...
Transcript of ASSEMBLY INSTRUCTIONS Wallaby IIarrowcabinets.com/wp-content/pdf/WallabyII-Assembly-Manual.pdf ·...
-
SEW IN COMFORT. SEW LONGER.™
ASSEMBLY INSTRUCTIONS
Wallaby I IITEM NO.: K8405 Teak
K8411 White Ash
-
2Wallaby II Assembly Instructions
Read the instructions carefully before starting. Please open and inspect the contents of boxes to see that all parts are included. You will need a Phillips head and a flat head screwdriver. A power screwdriver or cordless drill is preferable. Ensure that the Phillips head fits neatly and fully engages the screw to avoid damage to the screws. Make sure that you tighten all screws securely and tap wooden dowels all the way in.
Use and Care
Your cabinet normally requires a minimum amount of maintenance; however, the following points are worth noting:
Cleaning – To remove marks and enhance the surface, wipe with general purpose cleaner.
Caution – Do not use ammonia-based cleaning agents. Do not use harsh chemicals or abrasive cleansers. The surface can be wiped with a damp cloth but should be dried quickly.
Electrical and Hydraulic Lifts – Require annual lubrication.
180°
Screw cam bolts flush as illustrated.
Press cam Into hole until flush with surface. The arrow direction must be in the direction of the hole!
Insert bolt through pre-drilledhole in edge of panel.
Understanding How the Cam Fastener Works
Turn clockwise to lock cam with bolt.
-
3Wallaby II Assembly Instructions
Parts ListITEM DESCRIPTION QTY. PACK.
A Top Panel 1 1 of 4
B Right Leaf 1 1 of 4
C Left Leaf 1 1 of 4
A5 Platform Cover 1 1 of 4
G Bottom Panel 1 1 of 4
D Back Panel 1 2 of 4
Z Right Side Panel 1 2 of 4
A1 Quilt Extension Panel 1 2 of 4
V1 Left Door Panel 1 2 of 4
V2a Right Main Door Panel 1 3 of 4
X Left Side Panel 1 3 of 4
Y Partition 1 3 of 4
F Fixed Shelf 1 3 of 4
ITEM DESCRIPTION QTY. PACK.
V2b Right Door Edge Panel 1 3 of 4
L Drawer Front 1 3 of 4
L1 Drawer Side Left 1 3 of 4
L2 Drawer Side Right 1 3 of 4
L3 Drawer Back 1 3 of 4
L4 Drawer Bottom 1 3 of 4
O Insert Holder 1 3 of 4
01 Gate Leg 1 3 of 4
K1 Door Bin Front Panel 1 3 of 4
K2 Door Bin Bottom Panel 1 3 of 4
K3 Door Bin Sides 2 3 of 4
K4 Fixed Shelf On Door 3 3 of 4
A4 Platform 1 3 of 4
Lift & Rails 1 4 of 4
K3
K3K1
K2
K4
K4
K4
V2a
V2b
Z
A
C
B
A5
A1
O1
D A4
O
G
X
V1
F
Y
L3
L1L4
L
L2
-
4Wallaby II Assembly Instructions
Parts List
6x35 Cam Bolt x35
3.5x14 Screw x52 3x14 Screw x28 3x20 Screw x4
Wrench x1 Handle x2 Door Plate x2 14mm Spanner x1
Stay Arm x1
Cam
6x25 Cam Bolt x255⁄8“ Cam Cover x60 6x50 Dowel Pin x33
Alignment Pin x1
Flap Hinge x3
Caster x3 Locking Plate Caster x5
Butt Hinge x2 Flush Hinge x6
Lock x1Magnet x1Lock plate x1Catch plate x1Key x2
8x16 Fix Bolt x20 4x20 Fix Bolt x4
Pre-installed parts
ITEM DESCRIPTION QTY.
c1 6x35 Cam Bolt 35
c3 6x25 Cam Bolt 25
d1 8x30 Dowel Pin 36
d2 6x50 Dowel Pin 33
c2 5⁄8“ Cam Cover 60
t2 Locking Plate Caster 5
a Wrench 1
s2 3x14 Screw 28
S Stay Arm 1
r3 14mm Spanner 1
d3 Door Plate 2
s5 Alignment Pin 1
ITEM DESCRIPTION QTY.
s3 3.5x35 Screw 4
h Handle 2
h3 Flap Hinge 3
h2 Flush Hinge 6
b2 4x20 Fix Bolt 4
b1 8x16 Fix Bolt 20
s1 3.5x14 Screw 52
m Magnet, Catch Plate 1
L Lock, Lock Plate, Keyx2 1
t1 Caster 3
h1 Butt hinge 2
s4 3x20 Screw 4
d2
s5
b2 s2 s4
h d3 r3
h1 h2
Lm
t1 t2 Drawer RunnersCaster Bracket
8x30 Dowel Pin x12d1
3.5x35 Screw x4
c1 c3
h3
b1 s1
a
s
c2
c5
s3
-
Wallaby II 5 Assembly Instructions
3.5x14 Screw x23
Stay Arm x1
8x30 Dowel Pin x12
Magnet x1
Lock Plate x1
Catch Plate x1
d1
r3
L
m
t1
Step 1. Preparation Panels A, A1, Z, X, F and O11. Insert cams bolts c1 into panels A, X and Z as illustrated below.2. Insert dowel pins d1 to panels X, Z and F as illustrated below..3. Fix Stay Arm s using Screws s1 to panel A as illustrated below.4. Fix Lock Plate using Screws s1 to panel A as illustrated below. Orient the flat face of lock plate L towards front edge of
panel A.5. Fix Magnet m using Screw s1 to panels A1 as illustrated below.6. Fix Flap Hinge h3 using Screw s1 to panels A1 as illustrated below.7. Fix Butt hinges h1 using Screws s1 as shown on Panel O1. Insert the Alignment pin s5.8. Insert the caster t1 into the pre-installed caster bracket on panel O1 and tighten with spanner r3.9. Fix Catch plate m to panel O1 using screws s1.
h3
Flap Hinge x3
14mm Spanner x1
Caster x1
6x35 Cam Bolt x15
Butt Hinge x2
Alignment Pin x1
c1
c1
c1
h3
s1
s1
s1
s1
s1
s
s
Z
A
O1
A1
X
F
L
m
t1
r3
s5
s1
s1
h1
c1
m
h1
s5
-
6x25 Cam Bolt x25
c3
4x20 Fix Bolt x4
b2
Wallaby II 6 Assembly Instructions
3.5x14 Screw x4
Step 2. Preparation Panels Y, D, 0, V1, V2a, V2b, K1, K3, K4, L, L3 and L21. Insert cam bolts c1 into panels Y and V2a and L as illustrated below.2. Insert cam bolts c3 into panels V2a, K1 and K3 as illustrated below.3. Insert dowel pins d1 into edges of panels Y, D, V2b, L1 and L2 using glue as illustrated below.4. Insert dowel pins d2 into top of panels K4 using glue to secure.5. Fix Lock mechanism L into corner of V2a using s4 screws. Add trim ring to exterior end of lock.6. Fix Door plate d3 to panel V1 using screws s1.7. Attach Flush Hinges h2 to panel V1 using s2 screws as shown.8. Attach the screw-in caster to V1 and V2a panel caster bracket and tighten with spanner t1.9. Attach door handles h to exterior of V1 and V2a using fix bolts b2 as shown.
14mm Spanner x1
Caster x2
x3
6x35 Cam Bolt x6
6x50 Dowel Pin x33
3x20 Screw x4
Lock x1Key x2
Door Plate x2
Flush Hinge x3
3x14 Screw x6
Handle x2
8x30 Dowel Pin x12
c1
c1
c1
c1
c1
b2
h
h2
s1
s2
D
Y
L
Ls4
t1
r3
d3
c3
c3
c3
K3
K1
K4V2a
V2b
O
V1
L
d3
h2
d1
r3
t1
c1
s1
d2
s4
L
s2
h
x2
L2
L1
-
Wallaby II 7 Assembly Instructions
3.5x14 Screw x3
Step 3. Fix Lifter Rail (right) to Z panel with s1 screws following predrilled holes as shown on the illustration below.
Step 4. Fix Lifter Rail (Left) to Y panel with s1 screws following predrilled holes as shown on the illustration below.
Lifter Rail (Right) x1
Lifter Rail (Left) x1
3.5x14 Screw x3
Rail faces front of panel.Detail beside shows the holes on back as it attaches to panel.
s1
s1
s1
s1
Y
Z
-
Wallaby II 8 Assembly Instructions
Step 5. Panels D, X, Z assembly.Insert cam bolts c1 on panels X and Z into cams on panel D and tighten in a clockwise direction as illustrated below. Apply cam covers c2 over tightened cams.
Panel D has the cams facing outside to the back of the cabinet and will be covered with stickers provided.
Step 6. Panel F and Y assembly.Insert cam bolts c1 on panels X and Y into cams on panel F and tighten in a clockwise direction as illustrated below. Apply cam covers c2 over tightened cams.
Important Note:We recommend doing this step with panels upside down so panels are in correct position for Step 6 on page 8 and Step 8 on page 9.
180°
180°
5⁄8“ Cam Cover x4
5⁄8“ Cam Cover x4
Z
ZY
F
D
D
X
X
c2
c2
c5
c5
-
180°
Wallaby II 9 Assembly Instructions
Step 7. Panel G assembly.1. Fix casters t2 to panel G with bolts b1 as illustrated below.2. Flip panel G over to top side. Install cam bolts c1 as illustrated below.3. Attach insert holder O by inserting cam bolts c1 on panel G into O and tightening cams clockwise.
Step 8. Panel G assembly.1. Remove the drawer runners from panels X and Y.2. Insert cam bolts c1 on panel G into cams on panels X, D, Y and Z and tighten in a clockwise direction as illustrated
below. Apply cam covers c2 over tightened cams.3. Attach the drawer runners on panels X and Y.
Locking Plate Caster x5
8x16 Fix Bolt x20
6x35 Cam Bolt x11
Wrench x1
180°
5⁄8“ Cam Cover x9
1.2.
3.
G
X
X
YX
Y
Y
ZD
G
t2
t2
b1
b1
c1
a
OG
c5
c2
c5
-
Wallaby II 10 Assembly Instructions
Step 10. Lifter Panel assembly.Fix Lifter to A4 panel with s1 screws following predrilled holes as shown on the illustration below.Note: Remove cable ties (do not remove wooden block).
Step 9. Flip cabinet over (right side up).
3.5x14 Screw x4
s1
Lifter x1
A4
s1
-
Wallaby II 11 Assembly Instructions
Step 12. Panel A assembly.1. Insert cam bolts c1 on panel A into cams on panels X, D, Y and Z and tighten in a clockwise direction as illustrated.
Apply cam covers c2 over tightened cams.
Step 11. Mounting the Lifter Assembly.1. Position lifter onto side rails using plastic guides; make sure the cable is hooked into the rail tabs on both sides then
lower the lift. See illustration below.2. When lifter is pushed to first lock position remove a small wooden block that will be released from lifter.
180°
5⁄8“ Cam Cover x9
Plastic guides Cable
Lifter rail
Lifter rail
Rail tabs
A4
c2
Y
A
X
Z
D
c5
-
Wallaby II 12 Assembly Instructions
Step 14. Drawer assembly.
Step 13. Drawer assembly.1. Insert cam bolts c1 on panel L into cams on panels L1 and L2 and tighten in a clockwise direction as illustrated below.
Apply cam cover c2 over tightened cams.2. Slide bottom L4 into L, L1, L2 and L3 grooves as illustrated.3. Connect drawer panels L1, L2 and L3 with screws s3 as illustrated below.
Apply cam cover c2 over tightened cams.
180°
5⁄8“ Cam Cover x4
3.5x35 Screw x4
s3
L
L3
L4
L2
L
L1
c2
c5
s3
-
Wallaby II 13 Assembly Instructions
Step 16. Panel V2 assembly.1. Insert cam bolts c1 on panel V2a into cams on panels V2b and tighten in a clockwise direction as illustrated below.2. Insert cam bolts c3 on panel V2a into cams on panels K1 and K4 and tighten in a clockwise direction as illustrated below.3. Fix flush hinges h2 to panel V2b with screws s2 as illustrated below.
Apply cam covers c2 over tightened cams.
Step 15. Door Bin assembly.1. Insert cam bolts on K3 sides into cams in K2 bottom panel and tighten cams in clockwise direction.2. Insert cam bolts on K1 front into cams in K2 bottom panel and sides K3 and tighten cams in clockwise direction.
5⁄8“ Cam Cover x13
180° 180°
c5
Flush Hinge x3
3x14 Screw x6
K1 K3
K2
K3
K4
K4
K4
c5
c2
V2a
V2b
K1
h2
h2
s2
s2
-
Wallaby II 14 Assembly Instructions
Step 18. Panel V1 assembly.1. Fix flush hinges h2 on panel V1 to X with screws s2 as illustrated below.2. Fix Stay Arm s with Screws s1 to panel V1 as illustrated below.3x14 Screw x6
s2
s
Step 17. Panel V2 assembly.Fix Flush hinges h2 on panel V2b to Z with screws s2 as illustrated below. It is helpful to have two people hold the door, but it is not required.3x14 Screw x6
V1
X
s2
h2
3.5x14 Screw x2
s1
s1
V2bZ
s2
s2
h2
-
Wallaby II 15 Assembly Instructions
Step 20. Panel A1 assembly.1. Have a second person hold the A1 Quilt panel balanced on the gate leg panel O1.2. Using screws s1 attach the flap hinges h3 to panels D and A1 from underneath panel A1.
Step 19. Panel 01 assembly.1. Fix O1 panel butt hinges h1 on to panel D with screws s1 as illustrated below.
s1
D
D
O1
O1
A1
3.5x14 Screw x9
3.5x14 Screw x6
s1
s1
s1
h1
h3
-
SEW IN COMFORT. SEW LONGER.™
LIMITED LIFETIME WARRANTYKangaroo™ Sewing Furniture Limited Lifetime Warranty
WHAT THIS WARRANTY COVERS: Arrow Companies, LLC (Arrow) provides limited warranty coverage to the original purchaser of this product against defects in materials or workmanship of Arrow furniture components for a period of ten years from the date of purchase. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
HOW TO GET SERVICE: Simply contact Arrow at 1-800-533-7347 or [email protected]. When you request warranty service, you must also present proof of purchase documentation, which includes the date of purchase (detailed receipt), and photos of the product. Arrow will replace any defective part (at its sole option), excluding labor. Replacement parts will be warranted for only the remaining period of the original Warranty.
Replacement parts will be shipped freight prepaid on any initial warranty claim during first year of Warranty only. Warranty applies only to defects confirmed by Arrow Companies, LLC and will be replaced or repaired at Arrow’s option. In the event parts are no longer available for a warranty claim, customer may receive brand new cabinet at a price equal to 60% off the MSRP of a current comparable model.
WHAT’S NOT COVERED: There is no warranty coverage for defects or conditions that result from the failure to follow product assembly instructions, information or warnings, misuse or abuse, intentional damage, fire, flood, alteration or modification of the product, or use of the product in a manner inconsistent with its intended use, nor any condition resulting from incorrect or inadequate maintenance, cleaning, or care, or neglect, cuts or scratches. Caster damage as a result of moving furniture fully loaded or with locked casters. Damage resulting from electrical surge or lightning. Use in commercial or education environments. Kangaroo Sewing Furniture is designed for residential use only.
ARROW SHALL HAVE NO LIABILITY for ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND and all such damages are EXCLUDED FROM THIS WARRANTY, such as loss of use, disassembly, transportation, labor or damage to property on or near the product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. The Warranty cannot be transferred to subsequent owners or users of the product, and it shall be immediately void in the event the product is resold, transferred, leased or rented to any third party or person other than the original purchaser.
ADDITIONAL LIMITATIONS:
THERE ARE NO OTHER WARRANTIES APPLICABLE TO THIS PRODUCT. Under the laws of certain states, there may be no implied warranties from Arrow and all implied warranties, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE are disclaimed where allowed by law. TO THE EXTENT ANY IMPLIED WARRANTIES ARE APPLICABLE, ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THIS EXPRESS WARRANTY or the minimum period allowed by law, whichever is shorter. Some states do not allow limitations on how long an implied Warranty lasts, so the above limitation may not apply to you. This limited warranty gives you specific legal rights. This limited warranty does not, in any way, affect the rights given to you by law.
REGISTER YOUR PRODUCT: Original purchaser should register the purchase online at www.ArrowCabinets.com/warranty.
-
SEW IN COMFORT. SEW LONGER.™
Enhance your sewing experience with a custom-made insert for your Arrow or Kangaroo cabinet. Inserts are designed to reduce the gap between the machine and cabinet opening. This provides an ergonomic work surface for the free arm of the sewing machine, allowing for straighter stitches, less fatigue and an overall better experience using your machine and cabinet.
Hydraulic Sewing Chair
Insert
Our adjustable height sewing chair is a perfect accessory for any craft and sewing room. The chair’s height is adjustable with easy to use controls and the cushions provide perfect lumbar support and comfort for those long sewing hours. Chair features five casters on a star base for greater movement at your sewing cabinet or crafting surface. Lift the seat cushion to reveal a hidden storage compartment for your small notions or patterns.
Accessories to Complete Your Sewing Experience
P.O. Box 307 Delavan, WI 53115 1-800-533-7347 Ext. 1
[email protected] www.ArrowCabinets.com 07-20
Custom Insert Arrow Sewing Chairs