Assembly Instructions Page 1 of 17 - Kids Bunk Beds · STUDENT LOFT BED - Assembly Instructions NE...

17
STUDENT LOFT BED Assembly Instructions NE kids · 2300 Prospect Dr. Christiansburg, VA 24073 · www.ne-kids.com NE kids Item No. X080 1. Follow the information on the warnings appearing on the upper bunk end structure and on the carton. Do not remove warning label from bed. 2. Always use the recommended size mattress or mattress support, or both, to help prevent entrapment or falls. 3. Surface of mattress must be at least 5 inches (127 mm) below the upper edge of guardrails. 4. Do not allow children under 6 years of age to use the upper bunk. 5. Prohibit more than one person on the upper bunk. 6. Periodically, check and ensure that the guardrail, stairs, and other components are in their proper position, free from damage, and that all connectors are tight. 7. Do not allow horseplay on or under the bed and prohibit jumping on the bed. 8. Always use the stairs for entering and leaving the upper bunk. 9. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts. 10. Use of a nightlight may provide added safety precaution for a child using the upper bunk. 11. Always use guardrails on both long sides of the upper bunk. If bunk bed will be placed next to the wall, the guardrail that runs the full length of the bed should be placed against the wall to prevent entrapment between the bed and wall. 12. The use of water or sleep flotation mattresses is prohibited. 13. Keep these instructions for future reference. ! ! STRANGULATION HAZARD Never attach or hang items to any part of the bunk bed that are not designed for use with the bed; including, but not limited to, hooks, belts and jump ropes SIZE OF MATTRESS AND FOUNDATION Use only mattress, foundation and deck combined which is 74-75 inches long and 37 ½-38 ½ inches wide on upper bunk. Ensure thickness of mattress and foundation combined does not exceed 8 inches and the mattress is at least 5 inches below upper edge of guardrails. SAFETY WARNINGS SAFETY FIRST! All of NE kid’s Bunkbeds were designed and manufactured with your child’s safety as our top priority. Their unparalleled strength is a bi-product of the safety design. Our bunks meet all compliance with ASTM F 1427-07 “Standard Consumer Safety Specification for Bunk Beds” and Code of Federal Regulations (CFR) 1213 “Safety Standards for Entrapment Hazards in Bunk Beds” and (CFR) 1513 “Requirements for Bunk Beds”. Safety is a cooperative effort between us as the manufacturer, and you as a guardian. Please read and consider the warnings listed on this page when choosing a mattress and discussing rules of use with your child. REPLACEMENT PARTS Replacement parts, including additional guardrails, may be obtained from any of NE kids’ dealers. Page 1 of 17

Transcript of Assembly Instructions Page 1 of 17 - Kids Bunk Beds · STUDENT LOFT BED - Assembly Instructions NE...

STUDENT LOFT BEDAssembly Instructions

NE kids · 2300 Prospect Dr. Christiansburg, VA 24073 · www.ne-kids.com

NEk i d s

Item No. X080

1. Follow the information on the warnings appearing on the upper bunk end structure and on the carton. Do not remove warning label from bed.

2. Always use the recommended size mattress or mattress support, or both, to help prevent entrapment or falls.

3. Surface of mattress must be at least 5 inches (127 mm) below the upper edge of guardrails.

4. Do not allow children under 6 years of age to use the upper bunk.

5. Prohibit more than one person on the upper bunk.

6. Periodically, check and ensure that the guardrail, stairs, and other components are in their proper position, free from damage, and that all connectors are tight.

7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.

8. Always use the stairs for entering and leaving the upper bunk.

9. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.

10.Use of a nightlight may provide added safety precaution for a child using the upper bunk.

11.Always use guardrails on both long sides of the upper bunk. If bunk bed will be placed next to the wall, the guardrail that runs the full length of the bed should be placed against the wall to prevent entrapment between the bed and wall.

12.The use of water or sleep flotation mattresses is prohibited.

13.Keeptheseinstructionsforfuturereference.

!

!STRANGULATIONHAZARDNever attach or hang items to any part of the bunk bed that are not designed for use with the bed; including, but not limited to, hooks, belts and jump ropes

SIZEOFMATTRESSANDFOUNDATIONUse only mattress, foundation and deck combined which is 74-75 inches long and 37 ½-38 ½ inches wide on upper bunk. Ensure thickness of mattress and foundation combined does not exceed 8 inches and the mattress is at least 5 inches below upper edge of guardrails.

SAFETYWARNINGSSAFETYFIRST!All of NE kid’s Bunkbeds were designed and manufactured with yourchild’ssafetyasourtoppriority.

Their unparalleled strength is a bi-product of the safety design. Our bunks meet all compliance with ASTM F 1427-07 “Standard Consumer Safety Specification for Bunk Beds” and Code of Federal Regulations (CFR) 1213 “Safety Standards for Entrapment Hazards in Bunk Beds” and (CFR) 1513 “Requirements for Bunk Beds”.

Safety is a cooperative effort between us as the manufacturer, and you as a guardian. Pleasereadandconsiderthewarningslistedonthispagewhen choosing a mattress and discussing rules of use with your child.

REPLACEMENTPARTSReplacement parts, including additional guardrails, may be obtained from any of NE kids’ dealers.

Page 1 of 17

Page 2 of 17

NE kids · 2300 Prospect Dr. Christiansburg, VA 24073 · www.ne-kids.com

NEk i d s

Enclosedpleasefindsimplestep-by-stepinstructionstohelpyouquicklyassembleyourproduct. Before you begin we recommend that you follow the steps below:

Please read the instructions thoroughly

Identify all parts and hardware

Gather the tool(s) necessary

2 adults required for assembly

Toprotectyourparts during assembly please place them on a soft surface.To clean surface use only water on a damp cloth. Do not use window cleaners or cleaning abrasives as it will scratch the surface and could damage the protective coating.

CUSTOMERSUPPORTIf you are missing parts or need assistance with your product, please contact the retailer from whom you purchased the product. When you call or email, please include the Product’s Item Number and PO Number which is located on the Production Tracking Sticker. This sticker can be found on the bottom, inside or back of your product.

1.

2.

3.

4.

INTRODUCTION

STUDENT LOFT BEDItem No. X080

Assembly Instructions

Fully AssembledStudent Loft

STUDENT LOFT BED - Assembly Instructions

NE kids · 2300 Prospect Dr. Christiansburg, VA 24073 · www.ne-kids.com

NEk i d s

Page 3 of 17

J

10mm Wood DowelsX4

Allen WrenchX1

K

L

PARTS LIST

H

30mm ScrewsX26

1

2

3

4

7

8

9 10

5

6

C

60mm BoltsX16

F

Barrel NutsX24

D

40mm BoltsX23

25mm BoltsX2

T-NutsX2

Ladder HooksX2

A 100mm BoltsX8

B

G

8mm Wood DowelsX12

E

45mm ScrewsX4

I

20mm ScrewsX12

11

Top

Bottom

Left & Right Desk Hutch Side PanelsX1ea.

Desk Hutch Top Panel

X1

Desk CabinetX1

BookcaseTop Panel

X1

BookcaseSide Panel

X1

BookcaseDrawer Chest

X1

BookcaseShelves

X2

Desk TopX1

Desk Hutch Back SupportsX1(of each type)

STUDENT LOFT BED - Assembly Instructions

NE kids · 2300 Prospect Dr. Christiansburg, VA 24073 · www.ne-kids.com

NEk i d s

Page 4 of 17

PARTS LIST (CONTINUED)

LadderX1

Rear Guard RailX1

Front Guard RailX1

15 16 17

Head/FootboardsX2

12

Set of SlatsX1

14

RailsX2

13

Other Tools Required(Not Included)

• Phillips Screwdriver

• Flathead Screwdriver

STUDENT LOFT BED - Assembly Instructions

NE kids · 2300 Prospect Dr. Christiansburg, VA 24073 · www.ne-kids.com

NEk i d s

Page 5 of 17

For left-hand Desk/Ladder follow directions as indicated.

For right-hand Desk/Ladder follow directions as indicated but

please note inset drawings.

NOTE: Before beginning assembly, decide exactly where the bed is to be placed and on which ends you would like the the Desk/Ladder and Bookcase. Both the Bookcase and Desk can be placed at either end and reversed. See below.!

STUDENT LOFT BED - Assembly Instructions

NE kids · 2300 Prospect Dr. Christiansburg, VA 24073 · www.ne-kids.com

NEk i d s

Page 6 of 17

STEP 1 STEP 2

Remove drawers from chest. Assemble Drawer Chest, Shelves and Bookcase Side Panel

X2

X2

X2

X2B

B

B

B

B

B

B

B

E

E

E

E

1

1

2

3

3

STUDENT LOFT BED - Assembly Instructions

NE kids · 2300 Prospect Dr. Christiansburg, VA 24073 · www.ne-kids.com

NEk i d s

Page 7 of 17

STEP 3 STEP 4

Withtwoadults, lift the Bookcase into desired position then replace the Drawers.

Attach Head/Footboard to Bookcase Top Panel then attach Top Panel to Bookcase.

Left-hand Bookcase(Right-hand Desk/Ladder)

C

C

C

C

C

CC

C

4

4

12

12

STUDENT LOFT BED - Assembly Instructions

NE kids · 2300 Prospect Dr. Christiansburg, VA 24073 · www.ne-kids.com

NEk i d s

Page 8 of 17

STEP 5

Loosely affix Desk Top to Right Desk Hutch Side Panel (do not completely tighten bolts). Remove drawers from Desk Cabinet, then attach Right Desk Hutch Side Panel to Desk Cabinet.

X2

X2

C

C

For outside-facing Desk assembly, please continue with Step 6 on Page 9.

For inside-facing Desk assembly, please skip to

Step 6A on Page 11.

NOTE: Before continuing assembly, decide whether you would like the Desk to be outside-facing or inside-facing and follow instructions below. For use of the Lower Bed with the Student Loft, Desk must be outside-facing.

!

10

5

5

F

F

B

B

E

E

10

8

STUDENT LOFT BED - Assembly Instructions

NE kids · 2300 Prospect Dr. Christiansburg, VA 24073 · www.ne-kids.com

NEk i d s

Page 9 of 17

STEP 6

Fit Desk Hutch Back Supports, Desk Top, and Left Desk Hutch Side Panel together using wood dowels(12).

Steps 6-8: Outside-facing Desk assembly

STEP 7

Secure Desk Hutch Side Panels and Back Supports as shown and tighten any bolts that were left loose.

FRONT VIEW

REAR VIEW

J

J

B

BB

B

B

B

B

F

F

F

F

F

F

F

F

F

F

E

E

E

E

E

E

E

K

K

D

7

8

9

6

10

5

STUDENT LOFT BED - Assembly Instructions

NE kids · 2300 Prospect Dr. Christiansburg, VA 24073 · www.ne-kids.com

NEk i d s

Page 10 of 17

STEP 8

Attach Desk Hutch Top Panel.

Skip to Step 9 on Page 12

C

C

C

C

D

D

D

D

11

STUDENT LOFT BED - Assembly Instructions

NE kids · 2300 Prospect Dr. Christiansburg, VA 24073 · www.ne-kids.com

NEk i d s

Page 11 of 17

Fit Desk Hutch Back Supports, Desk Top, and Left Desk Hutch Side Panel together using wood dowels(12).

Secure Desk Hutch Side Panels and Back Supports as shown and tighten any bolts that were left loose.

REAR VIEW

J

J

B

B

BB

B

B

F

F

F

F

F

F

F

F

F

FE

E

E

EE

E

E

K

K

D

STEP 8ASTEP 6A STEP 7A

Attach Desk Hutch Top Panel.

CC

CC

DD

D

Steps 6A-8A: Inside-facing Desk assembly

7

8

9

6

10

5

11

STUDENT LOFT BED - Assembly Instructions

NE kids · 2300 Prospect Dr. Christiansburg, VA 24073 · www.ne-kids.com

NEk i d s

Page 12 of 17

STEP 10

Attach Headboard to the top of the Desk Hutch.

Steps 10-14: Upper Bed assemblySTEP 9

Withtwoadults, move the Desk Hutch into position then replace the drawers.

For inside-facing Desk assembly

For outside-facing Desk assembly

C CC C

C CC C

12 12

STUDENT LOFT BED - Assembly Instructions

NE kids · 2300 Prospect Dr. Christiansburg, VA 24073 · www.ne-kids.com

NEk i d s

Page 13 of 17

STEP 11

Loosely attach Desk Hutch, Bed Side Rails and Bookcase (do not completely tighten bolts until Step 13).

Detail for all four corners

I

I

I

I

A

A

A

A

E

E

E

E 13

13

STUDENT LOFT BED - Assembly Instructions

NE kids · 2300 Prospect Dr. Christiansburg, VA 24073 · www.ne-kids.com

NEk i d s

Page 14 of 17

STEP 12

Lay slat roll between side rails and screw in slats to slat support as indicated. Make sure rails are pulled into slats prior to screwing in place.

To help prevent serious or fatal injuries SCREWBOTHSIDESOFEACHSLATTOTHESLATSUPPORT. Failure to do so could result in the collapse of the entire slat roll, and will void your warranty.

WARNING!

Attach Slats.G

G

G

14

14

STUDENT LOFT BED - Assembly Instructions

NE kids · 2300 Prospect Dr. Christiansburg, VA 24073 · www.ne-kids.com

NEk i d s

Page 15 of 17

Position Guard Rails in place, tighten all Bed Side Rail bolts completely, then attach Guard Rails as shown. Note: Ladder opening must be on the Desk end of the bed.

Inside detail

Detail for 3 corners

STEP 13

Right-hand Desk/Ladder

H

H

H

C

15

15

16

16

STUDENT LOFT BED - Assembly Instructions

NE kids · 2300 Prospect Dr. Christiansburg, VA 24073 · www.ne-kids.com

NEk i d s

Page 16 of 17

Attach Ladder Hooks to Ladder, then attach Ladder to Upper Bed.

Inside detail

STEP 14

L

L

17

H

HH

H

Note: Please ensure that the bolts for Ladder rungs are tight before using.

STUDENT LOFT BED - Assembly Instructions

NE kids · 2300 Prospect Dr. Christiansburg, VA 24073 · www.ne-kids.com

NEk i d s

Page 17 of 17

CARE INSTRUCTIONS

• A lacquer finish is used on this furniture to protect the wood. It is not waterproof, clean spills immediately. Dust using a slightly damp cloth, making sure no standing water is left on the furniture. DO NOT use any household cleaners, citrus-based polishes, wood soaps, or oils; they can break down the natural lacquer finish.

• Do not place furniture in direct sunlight. Natural solid wood furniture will naturally color as it ages, however, direct sunlight dramatically speeds up the process.

• In natural wood furniture, the variations in texture and grain will affect the finish, making it impossible to guarantee an exact match between two pieces of wood even though identical finishing processes are used. These differences in character are not defects, but variations that make each piece of furniture unique and beautiful.

• Solid wood naturally expands and contracts. In high humidity you may find that drawers can stick slightly. This will correct itself, and is not reason for concern.

• Do not place furniture over heating or cooling vents. Dramatic changes in temperature can cause the wood to split.

• If you place objects such as lamps or plants on your case pieces make sure to move them from time to time. There may be a slight discoloration where the object was. However, by exposing it to light the color will catch up to the rest of the case.

• Plastic or foam footed items such as phones or clocks can damage this finish, use trivets under such items.