ASSEMBLY INSTRUCTIONS - Focus Foodservicefocusfoodservice.com/media/catalog/product/doc/ffs... ·...
4
ASSEMBLY INSTRUCTIONS Enclosure Panels on Wire Shelving with Aluminum Truck Dolly FOODSERVICE, LLC CAUTION: INSPECT CONTENTS IMMEDIATELY TO ENSURE PRODUCT WAS NOT DAMAGED DURING SHIPPING. Assemble Wire Shelving Unit to Truck Dolly Step 1 Unpack carton, identify and confirm quality of components. Step 2 Before assembly of shelving unit to Truck Dolly, unscrew the leveling feet on the posts (See Diagram 1). Step 3 Attach the posts to Truck Dolly frame, using leveling feet and washers and tighten down (See Diagram 2). Step 4 Choose the desired height of the bottom shelf (for added stability, it is recommended that the bottom shelf is installed no more than 6"(2 – 3 lines) above the truck dolly and the top shelf no more than 6"(2 – 3 lines) from the top.) Snap two (2) tapered sleeves, with the word UP on top, at the desired height on each post. (See Diagram 3) Shelves can be adjusted every 1". (Note: Double grooves in the posts are placed every 8th groove for simple shelf height reference.) Step 5 Snap the tapered sleeves into place on posts at the next desired shelf height. Slide the shelf down from the top of the posts onto the tapered sleeves and repeat this step for the remaining shelves. (Note: A rubber mallet may be used to tap each corner of the shelves so they firmly install onto the tapered sleeves.) Attach Enclosure Panels (See Diagram 4) Step 6 Place (2) S-hooks Assemblies such that they slide down over the top portion of each truss on the top shelf of the shelving unit. Make sure to space the S-hooks Assemblies so that they are approx. 4" from the shelving collars and aligned to the second square from each end of the side panels. Step 7 Attach the side panels: The (2) horizontal bars should face toward the shelving unit. Place the side panel onto the already positioned S-hooks. Make sure that the position of the S-hooks Assemblies are positioned on second horizontal bar. Step 8 Secure the side panels: Secure the S-hook Assemblies to the panel using the nut and bolt. Secure the bottom panel to the bottom shelf truss using C-Channel Bracket Assemblies. Space each approx. 3" from shelving collar. Step 9 Tighten all screws to ensure secure fit. Repeat process for remaining side panel and rear panels. Enclosure Panel Requirements Ends- Panels required for EACH end according to shelf widths as follows Nominal Post Height Nominal Shelf Width 18" (45.7 cm) 21" (53.0 cm) 24" (61.0 cm) 30" (76.0 cm) 36" (91.4 cm) 54" (137.2 cm) (1) FEP1854CH (1) FEP1854CH (1) FEP2454CH (2) FEP1854CH (1) FEP1854CH & (1) FEP2454CH 63" (160.0 cm) (1) FEP1863CH (1) FEP1863CH (1) FEP2463CH (2) FEP1863CH (1) FEP1863CH & (1) FEP2463CH 74" (188.0 cm) (1) FEP1874CH (1) FEP1874CH (1) FEP2474CH (2) FEP1874CH (1) FEP1874CH & (1) FEP2474CH Backs - Requires multiple panels IN QUANTITIES SHOWN for specific shelf lengths: Nominal Post Height Nominal Shelf Length 30" (76.0 cm) 36" (91.4 cm) 42" (106.6 cm) 48" (122.0 cm) 54" (137.0 cm) 60" (152.4 cm) 72" (182.9) 54" (137.2 cm) (2) FEP1854CH (1) FEP1854CH & (1) FEP2454CH (2) FEP2454CH (2) FEP1854CH & (1) FEP2454CH (1) FEP1854CH & (2) FEP2454CH (3) FEP2454CH (1) FEP1854CH & (3) FEP2454CH 63" (160.0 cm) (2) FEP1863CH (1) FEP1863CH & (1) FEP2463CH (2) FEP2463CH (2) FEP1863CH & (1) FEP2463CH (1) FEP1863CH & (2) FEP2463CH (3) FEP2463CH (1) FEP1863CH & (3) FEP2463CH 74" (188.0 cm) (2) FEP1874CH (1) FEP1874CH & (1) FEP2474CH (2) FEP2474CH (2) FEP1874CH & (1) FEP2474CH (1) FEP1874CH & (2) FEP2474CH (3) FEP2474CH (1) FEP1874CH & (3) FEP2474CH
Transcript of ASSEMBLY INSTRUCTIONS - Focus Foodservicefocusfoodservice.com/media/catalog/product/doc/ffs... ·...
ASSEMBLY INSTRUCTIONSEnclosure Panels on Wire Shelving with Aluminum Truck Dolly
FOODSERVICE, LLC
CAUTION: INSPECT CONTENTS IMMEDIATELY TO ENSURE PRODUCT WAS NOT DAMAGED DURING SHIPPING.
Assemble Wire Shelving Unit to Truck DollyStep 1 Unpack carton, identify and confirm quality of components. Step 2 Before assembly of shelving unit to Truck Dolly, unscrew the leveling feet on the posts (See Diagram 1).Step 3 Attach the posts to Truck Dolly frame, using leveling feet and washers and tighten down (See Diagram 2). Step 4 Choose the desired height of the bottom shelf (for added stability, it is recommended that the bottom shelf is installed no
more than 6"(2 – 3 lines) above the truck dolly and the top shelf no more than 6"(2 – 3 lines) from the top.) Snap two (2) tapered sleeves, with the word UP on top, at the desired height on each post. (See Diagram 3) Shelves can be adjusted every 1". (Note: Double grooves in the posts are placed every 8th groove for simple shelf height reference.)
Step 5 Snap the tapered sleeves into place on posts at the next desired shelf height. Slide the shelf down from the top of the posts onto the tapered sleeves and repeat this step for the remaining shelves. (Note: A rubber mallet may be used to tap each corner of the shelves so they firmly install onto the tapered sleeves.)
Attach Enclosure Panels (See Diagram 4)Step 6 Place (2) S-hooks Assemblies such that they slide down over the top portion of each truss on the top shelf of the shelving
unit. Make sure to space the S-hooks Assemblies so that they are approx. 4" from the shelving collars and aligned to the second square from each end of the side panels.
Step 7 Attach the side panels: The (2) horizontal bars should face toward the shelving unit. Place the side panel onto the already positioned S-hooks. Make sure that the position of the S-hooks Assemblies are positioned on second horizontal bar.
Step 8 Secure the side panels: Secure the S-hook Assemblies to the panel using the nut and bolt. Secure the bottom panel to the bottom shelf truss using C-Channel Bracket Assemblies. Space each approx. 3" from shelving collar.
Step 9 Tighten all screws to ensure secure fit. Repeat process for remaining side panel and rear panels.
Enclosure Panel Requirements Ends- Panels required for EACH end according to shelf widths as follows
Nominal Post Height
Nominal Shelf Width
18" (45.7 cm) 21" (53.0 cm) 24" (61.0 cm) 30" (76.0 cm) 36" (91.4 cm)
54" (137.2 cm) (1) FEP1854CH (1) FEP1854CH (1) FEP2454CH (2) FEP1854CH (1) FEP1854CH & (1) FEP2454CH63" (160.0 cm) (1) FEP1863CH (1) FEP1863CH (1) FEP2463CH (2) FEP1863CH (1) FEP1863CH & (1) FEP2463CH
74" (188.0 cm) (1) FEP1874CH (1) FEP1874CH (1) FEP2474CH (2) FEP1874CH (1) FEP1874CH & (1) FEP2474CH
Backs - Requires multiple panels IN QUANTITIES SHOWN for specific shelf lengths:
Nominal Post Height
Nominal Shelf Length
30" (76.0 cm) 36" (91.4 cm) 42" (106.6 cm) 48" (122.0 cm) 54" (137.0 cm) 60" (152.4 cm) 72" (182.9)
54" (137.2 cm) (2) FEP1854CH (1) FEP1854CH & (1) FEP2454CH (2) FEP2454CH (2) FEP1854CH & (1) FEP2454CH (1) FEP1854CH & (2) FEP2454CH (3) FEP2454CH (1) FEP1854CH & (3) FEP2454CH63" (160.0 cm) (2) FEP1863CH (1) FEP1863CH & (1) FEP2463CH (2) FEP2463CH (2) FEP1863CH & (1) FEP2463CH (1) FEP1863CH & (2) FEP2463CH (3) FEP2463CH (1) FEP1863CH & (3) FEP2463CH
74" (188.0 cm) (2) FEP1874CH (1) FEP1874CH & (1) FEP2474CH (2) FEP2474CH (2) FEP1874CH & (1) FEP2474CH (1) FEP1874CH & (2) FEP2474CH (3) FEP2474CH (1) FEP1874CH & (3) FEP2474CH
ASSEMBLY INSTRUCTIONS
Call Customer Service at 1.800.968.3918 | Fax 1.800.968.4129 www.focusfoodservice.com
rev. 0811
TaperedSleeves
Post
ShelfCollar
TaperedSleeve
Diagram 1
Part Truck DollyEnclosure Panels Required
(See Page 1)S-Hook
AssembliesC-Channel Assemblies
Qty 1 For 3 Sides 2 Per Panel 2 Per Panel
In demanding use situations and where thresholds are continually encountered. Focus recommends the use of stacked posts and aluminum split sleeves.
Diagram 2
Diagram 3
Diagram 4
Casters, Shelves, & Posts Sold Separately
FOODSERVICE, LLC
INSTRUCCIONES DE ARMADOPaneles de Cierre en Estantería de Alambre con Carro de Aluminio
FOODSERVICE, LLC
PRECAUCIóN: INSPECCIONE EL CONTENIDO INMEDIATAMENTE PARA ASEGURARSE DE QUE EL PRODUCTO NO SE HAYA DAÑADO DURANTE EL TRANSPORTE.
Ensamble la estantería de alambre sobre el carro Paso 1 Desempaque el cartón de embalaje e identifique y confirme la calidad de los componentes. Paso 2 Antes de ensamblar la estantería sobre el carro, desatornille los pies de nivelación de los postes (ver el Diagrama 1).Paso 3 Fije los postes al armazón del carro utilizando los pies de nivelado y las arandelas, y apriételos (ver el Diagrama 2). Paso 4 Decida la altura deseada para el estante inferior (para una mayor estabilidad, se recomienda que el estante inferior se instale a no más de 6
pulgadas (15 cm) (2 - 3 líneas) del piso y el restante superior a no más de 6 pulgadas (15 cm) (2 - 3 líneas) de la parte superior.) Inserte dos (2) manguitos ahusados, con la palabra "UP" hacia arriba, a la altura deseada en cada poste. (Ver el Diagrama 3) Los estantes pueden ajustarse cada 1 pulgada (2,5 cm). (Nota: A cada 8 ranuras de cada poste, se colocan ranuras dobles para tener una sencilla referencia respecto a la altura del estante.)
Paso 5 Inserte los manguitos ahusados en su lugar en los postes a la próxima altura deseada. Deslice el estante desde la parte superior de los postes y hacia abajo sobre los manguitos ahusados y repita este paso para los estantes remanentes. (Nota: Se puede utilizar un mazo de goma para dar golpecitos a cada esquina de los estantes de manera que queden firmemente instalados sobre los manguitos ahusados.)
Fijar los paneles de cierre (ver Diagrama 4)Paso 6 Coloque (2) los conjuntos de los ganchos en S de manera que deslicen sobre la parte superior de cada viga de celosía del estante superior
de la estantería. Asegúrese de espaciar los conjuntos de los ganchos en S de manera que estén a aproximadamente 4 pulgadas (10 cm) de los collarines de los estantes y que estén alineados con el segundo cuadrado de cada extremo de los paneles laterales.
Paso 7 Fije los paneles laterales: Las (2) barras horizontales deberán estar de cara hacia la estantería. Coloque el panel lateral sobre los ganchos en S ya colocados en su lugar. Asegúrese de que los conjuntos de los ganchos en S estén ubicados sobre la segunda barra horizontal.
Paso 8 Atornille los paneles laterales: Atornille los conjuntos de los ganchos en S utilizando el perno y la tuerca. Fije la parte inferior del panel a la viga de celosía del estante inferior utilizando los conjuntos de los soportes de canal en C. Espacie cada uno a aproximadamente 3 pulgadas del collarín de los estantes.
Paso 9 Apriete todos los tornillos para asegurarse de que el panel quede firmemente fijo. Repita el proceso para el panel lateral remanente y para los paneles posteriores.
Paneles de cierre requeridos Extremos: paneles requeridos para CADA extremo de acuerdo a las anchuras de los estantes según sigue:
Altura nominal del poste
Ancho nominal del estante
18" (45.7 cm) 21" (53.0 cm) 24" (61.0 cm) 30" (76.0 cm) 36" (91.4 cm)
54" (137.2 cm) (1) FEP1854CH (1) FEP1854CH (1) FEP2454CH (2) FEP1854CH (1) FEP1854CH & (1) FEP2454CH63" (160.0 cm) (1) FEP1863CH (1) FEP1863CH (1) FEP2463CH (2) FEP1863CH (1) FEP1863CH & (1) FEP2463CH
74" (188.0 cm) (1) FEP1874CH (1) FEP1874CH (1) FEP2474CH (2) FEP1874CH (1) FEP1874CH & (1) FEP2474CH
Partes posteriores: se requieren paneles múltiples en las CANTIDADES MOSTRADAS para cada longitud de estante en particular:
Altura nominal del poste
Longitud nominal del estante
30" (76.0 cm) 36" (91.4 cm) 42" (106.6 cm) 48" (122.0 cm) 54" (137.0 cm) 60" (152.4 cm) 72" (182.9)
54" (137.2 cm) (2) FEP1854CH (1) FEP1854CH & (1) FEP2454CH (2) FEP2454CH (2) FEP1854CH & (1) FEP2454CH (1) FEP1854CH & (2) FEP2454CH (3) FEP2454CH (1) FEP1854CH & (3) FEP2454CH63" (160.0 cm) (2) FEP1863CH (1) FEP1863CH & (1) FEP2463CH (2) FEP2463CH (2) FEP1863CH & (1) FEP2463CH (1) FEP1863CH & (2) FEP2463CH (3) FEP2463CH (1) FEP1863CH & (3) FEP2463CH
74" (188.0 cm) (2) FEP1874CH (1) FEP1874CH & (1) FEP2474CH (2) FEP2474CH (2) FEP1874CH & (1) FEP2474CH (1) FEP1874CH & (2) FEP2474CH (3) FEP2474CH (1) FEP1874CH & (3) FEP2474CH
INSTRUCCIONES DE ARMADO
Call Customer Service at 1.800.968.3918 | Fax 1.800.968.4129 www.focusfoodservice.com
rev. 0911
Manguitos ahusados
Poste
Collarines de los estantes
Manguitos ahusados
Diagrama 1
Pieza CarroPaneles de cierre requeridos
(ver página 1)Ensambles de ganchos en S
Ensambles de canales en C
Cant. 1 para 3 lados 2 por panel 2 por panel
En situaciones de uso exigentes y donde continuamente se topa contra los límites. Focus recomienda el uso de postes apilados y manguitos en dos mitades de aluminio.
Diagrama 2
Diagrama 3
Diagrama 4
Las ruedas, los estantes y los postes se venden por separado
FOODSERVICE, LLC
