R

01–Worksurface ............................... Qty. 1 ....................... (see below) 24” Wide Worksurface (F24029zz/xx3) ............100-6527-00 30” Wide Worksurface (F3029zz/xx3) ...............100-6432-00 36” Wide Worksurface (F3629zz/xx3) ...............100-6433-00 48” Wide Worksurface (F4829zz/xx3) ...............100-6417-0002– Support Bracket-B .................... Qty. 1 ...................225-2296-00

fi t Small Support Y fi t Small Support Y fi t (F2429zz/xx3) .. Qty. 1 ...................225-2015-0003– 22.875” Vertical Legs .................Qty. 4 ...................125-5213-0004– Base Tubes .......................................Qty. 2 ..................125-5273-0005– Cross Tubes ................................ Qty. 2 ....................... (see below) 24” Deep Base Tube (F2429zz/xx3) ....................125-5218-00 30” Deep Base Tube (F3029zz/xx3) ....................125-5219-00 36” Deep Base Tube F3629zz/xx3) ......................125-5220-00 48” Deep Base Tube (F4829zz/xx3) ....................125-5214-0006– Insert Screws ............................. Qty. 4 ...................325-5052-0007– 2” Large End Caps .................... Qty. 4 ...................175-5157-0008– 3” Locking Casters ................... Qty. 2 ...................150-5053-0009– Caster Inserts ............................ Qty. 4 ...................525-5032-00

Component list for part #’s F2429zz/xx3, F3029zz/xx3, F3629zz/xx3 & F4829zz/xx3

10– 5/16-18 fi t Bolts .......................... ...................325-5194-0011– fi t Tube Washers ....................... Qty. 8 ..225-2050-00 or 225-3522-00

12– 3” Non-Locking Casters ......... Qty. 2 ...................150-5052-0013– 3/4” Wood Screws ...................... Qty. 8 ...................325-5106-0014– Support Bracket-A .................... Qty. 1 ................. 225-2295 -00

fi t Small Support X fi t Small Support X fi t (F2429zz/xx3) .. Qty. 1 ...................225-2014-0015– Support Screws ......................... Qty. 8 ...................325-5010-0016– 1.5” Small Caps ......................... Qty. 4 ...................175-5156-0017– Back Trough ................................ Qty. 1 ....................... (see below) 24” Wide Back Trough (F2429zz/xx3) ................225-2289-00 30” Wide Back Trough (F3029zz/xx3) ................225-2290-00 36” Wide Back Trough (F3629zz/xx3) ................225-2291-00 48” Wide Back Trough (F4829zz/xx3) ................225-2292-0018– 1/4-20 Button Head Screws ....Qty. 4 ...................325-5003-00All Screw quantities listed here are the minimum needed for your Standard Unit assembly. There may be a few extra Screws included, which are not counted in the Parts List.

Anthro Corporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062 anthro.com

SAVE THESE INSTRUCTIONS! Rev. D January 2006

Step 8Align the Base Assembly on the Vertical Tubes as shown.

Secure the Base Assembly by inserting a fi t Bolt through a Tube Washer. Then insert the Bolt through the Base Tube and carefully thread it into the Vertical Tubes.

Repeat for the remaining three Bolts and tighten all Bolts.

Step 9Insert the four 1.5” Small End Caps into the Vertical Legs.

Congratulations! Your assembly is complete.

Please return the enclosed Registration Card to receive our product updates, new catalogs, and sale fl yers.

Thank you for choosing Anthro!

Hello! Thank you for choosing Anthro.

Before beginning assembly of your Standard Unit, please take a moment to review the parts listed below to verify that your shipment is complete.

Please review the assembly instructions of all Anthro products you purchased and are planning to include in this installation, prior to beginning this assembly.

To make the assembly of your Standard Unit even easier, we have included all of the required tools. The handy Hex Driver Bit can be used in your electric drill in place of the Hex Driver. Hex Driver 5/32” .........375-5000-00Hex Driver Bit 5/32” ....375-5003-008 oz. Rubber Mallet ....375-5022-00

Questions? 1-800-325-3841

1.5” Small End Cap

(5/16-18 X 3.5”) fi t Bolt325-5194-00

fi t Tube Washer225-2050-00 or 225-3522-00

04

06

07

05

01

13

14

18

fi t Boltfi t Bolt

fi t Tube WasherCross Tube

24”/30”/36”/48” wide Standard UnitAssembly Instructions

1-800-325-3841

NOTE: Detailed views of all Hardware are provided with each Assembly Step.

Step 7Attach a Cross Tube to a Base Tube by inserting a fi t Bolt through a Tube Washer, then insert the Bolt through the Base Tube and carefully thread into the Cross Tube.

Repeat this procedure for other Cross Tube. Then tighten all fi t Bolts.

fi t Tube Washer225-2050-00 or 225-3522-00

Cross Tube

fi t Tube Washer

(5/16-18 X 3.5”) fi t Bolt325-5194-00

fi t Bolt

Base Assembly

Anthro Corporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062

Step 1Place your Worksurface onto the fl oor with the pre-drilled holes facing upward.

Position the Support Brackets onto the Worksurface and align two of the holes on each Support Bracket with the predrilled holes on the Worksurface.

Loosely secure each Support Bracket to the Worksurface using two Wood Screws per Support Bracket.

NOTE: fi t Small Support X & Y, to be used in place of the Support Brackets (24” only).

anthro.com

Step 4Attach a Vertical Leg by installing two Support Screws through the Support Bracket-A into holes 1 & 3 from the top (non-coped end) of a Leg.

Repeat for the second Vertical Leg to be installed to Support Bracket-A.

Step 6Insert two End Caps into the ends of both Base Tubes.

Install two Caster Inserts into each Base Tube and secure with one Insert Screw per Insert.

Insert one Locking and one Non-Locking Caster into each Caster Insert of a Base Tube as shown.

Questions? 1-800-325-3841

Support Screw325-5010-00

Step 2Place the Back Trough onto the Worksurface, between the installed Support Brackets (from Step 1).

Align the two threaded holes on each end of the Back Trough with those on both Support Brackets. Carefully, thread one Button Head Screw through the Support Bracket, into the Back Trough. Repeat for remaining three Button Head Screws.

Insert two Wood Screws through the two remaining holes on the Back Trough fl ange (which should be aligned with two predrilled holes on the Worksurface) and tighten into place.

Step 5Attach the remaining Vertical Legs to Support Bracket-B using the same procedure used in Step 5.

NOTE: Make certain to install the Vertical Legs into the same holes used in Step 5.

Support Screw325-5010-00

3/4” Wood Screw325-5106-00

3/4” Wood Screw325-5106-00

(1/4-20 X .50”) Button Head Screw325-5003-00

Insert Screw(with pink threads)

325-5052-00

Locking Caster

Support Bracket-B

FIRST: Install the Button Head ScrewsFIRST: Install the Button Head ScrewsFIRST

SECOND: Install the Wood Screws

Back Trough

SECOND:

Back Support Flange

Support Bracket-A

Support Bracket-B

Caster Inserts placed into the large holes

Leave these two side holes open

Non-Locking Caster

Hole 1=29” Final Worksurface Height

Support Bracket-A

Support Bracket-B

Hole 1

Top(non-coped) (non-coped)

end

Bottom(coped)

end

Hole 3

Hole 1

Hole 3

Top(non-coped)

end

Bottom(coped)

end

NOTE: Make certain to install the Back Trough in front of the Support Brackets

Threaded Holes

24”/30”/36”/48” Standard UnitAssembly Instructions

fi t Small Support X & Y(24” Standard Unit Only)

Step 3Determine the best height for your Worksurface. These instructions will place your Worksurface 29” from the fl oor using the standard 3” casters.

For a fi nal Worksurface height that is lower than 29”, adjust one hole down for each inch of variance desired.

NOTE: Your Worksurface location may be changed after your Standard Unit has been completely assembled by repeating Steps 5 & 6.

29”