ASSEMBLY INSTRUCTION 1GHXL or C - Rubinet
8
1GHXL 1GHXC WALL MOUNT LAVATORY SET ASSEMBLY INSTRUCTION 1GHXL or C REMOVAL OF FAUCET: Always turn the water supply off before removing the existing faucet or disassembling a valve. Open both faucet handles to relieve water pressure and to ensure that the water has been successfully turned off. CARE OF FAUCET: The use of warm water and a soft cloth is all that is required to clean Rubinet products. The patina of our living finishes (Oil Rubbed Bronze & Tuscan Brass) will change as a result of normal use. Applying Mineral Oil on occasion will create a softer look, subtle color changes and character. 160927
Transcript of ASSEMBLY INSTRUCTION 1GHXL or C - Rubinet
1GHXL
1GHXC
CONTACT US: If you need assistance with installation, replacement parts or have any questions regarding your Rubinet product, please call a Customer Service representative at: 905-851-6781 toll free 1-800-461-5901 or visit www.rubinet.com
FEATURES:- Brass construction with choice of 21 finishes- Two Cross or Lever handles- Quarter-turn ceramic disk cartridges- 2.4 gpm @ 60 psi (Helps meet CalGreen regulation)
APPROVAL:- AB1953 / NSF61- ASME A 112.18.1- CSA B125.1
WALL MOUNT LAVATORY SET
ASSEMBLY INSTRUCTION 1GHXL or C
REMOVAL OF FAUCET: Always turn the water supply off before removing the existing faucet or disassembling a valve. Open both faucet handles to relieve water pressure and to ensure that the water has been successfully turned off.
CARE OF FAUCET: The use of warm water and a soft cloth is all that is required to clean Rubinet products. The patina of our living finishes (Oil Rubbed Bronze & Tuscan Brass) will change as a result of normal use. Applying Mineral Oil on occasion will create a softer look, subtle color changes and character.
160927
1 3/8"
HOL
ES35
2 1/2" MIN wall limit3 1/8" MAX wall limit
6 9/16"167
ALLO
W 4"
FROM
RIM
OF
FIXT
URE
FINISHED WALL
8"203
2 15/16"75
2 1/2"
Loosen the lock nut using * 17mm Deep Socket. 1/2“ Drive
LOCK NUTRecommended torque 20Nm
1 2
5 6
HANDLE ALIGNMENT (1G)
3 4
Use Handles to unscrew cartridge.Turn both splines counter clock-wise.
Once cartridge valves are loose, screw them back into the faucet using the handle.Stop when you feel a noticeable resistance.Then remove handles.
Replace Left Handle (hot) one tooth o�from the OFF position as shown.
And Right Handle (cold) one tooth o�from the ON position as shown.
Turn the handles to the desired alignment. (This will unscrew the cartridge)This adjustment should not be more than 25º.
Tighten Lock Nut using 17mm Deep Socket.wrench to secure cartridge valve position.
*Use handle to hold spline while tightening.
RemoveTHREADEDSLEEVE
LOCK NUT
5
WALL MOUNT LAVATORY SET 1GHXL or CWALL MOUNT LAVATORY SET 1GHXL or C
1GR000Wall Mount Valve Rough-In
9Y0HXFA1BFlange
HHX04 Cross Handle
Spout Ring
HHX01Lever Handle
9Y0HXST1ASpout
9YAERSW3AAerator * Turn counter-clock wise to unscrew.
9X0FBHA1EFlange Bushing
1 5/8˝
4 1
1 7/8˝
WALL MOUNT LAVATORY SET 1GHXL or CWALL MOUNT LAVATORY SET 1GHXL or C
MUST CUT FLUSH TO THE FLANGE TRIM
* 1 7/8˝ (47.5mm) from the finished wall
Flange
Pre-assembled Spout Ring
* Cut the Slip-Fit Shank 1 5/8˝ long from the finished wall and MUST REMOVE ANY BURRS before installing the Wall Spout.
Tighten set screws to secure
IF THE HANDLES DO NOT ALIGN CORRECTLYYou can adjust them. Please refer to the ‘Handle Alignment’ instruction at the back.
Lock Nut
2 3/4˝
2 3
WALL MOUNT LAVATORY SET 1GHXL or CWALL MOUNT LAVATORY SET 1GHXL or C
Turn each cartridge splines into OFF position before installing handles
Place handle on the spline.
Flange Bushing
IF THE HANDLE DOES NOT FIT
CUT THE SPLINE TO FIT* 2 3/4˝ (69.5mm)
from the finished wall
2 3/4˝
2 3
WALL MOUNT LAVATORY SET 1GHXL or CWALL MOUNT LAVATORY SET 1GHXL or C
Turn each cartridge splines into OFF position before installing handles
Place handle on the spline.
Flange Bushing
IF THE HANDLE DOES NOT FIT
CUT THE SPLINE TO FIT* 2 3/4˝ (69.5mm)
from the finished wall
1 5/8˝
4 1
1 7/8˝
WALL MOUNT LAVATORY SET 1GHXL or CWALL MOUNT LAVATORY SET 1GHXL or C
MUST CUT FLUSH TO THE FLANGE TRIM
* 1 7/8˝ (47.5mm) from the finished wall
Flange
Pre-assembled Spout Ring
* Cut the Slip-Fit Shank 1 5/8˝ long from the finished wall and MUST REMOVE ANY BURRS before installing the Wall Spout.
Tighten set screws to secure
IF THE HANDLES DO NOT ALIGN CORRECTLYYou can adjust them. Please refer to the ‘Handle Alignment’ instruction at the back.
Lock Nut
Loosen the lock nut using * 17mm Deep Socket. 1/2“ Drive
LOCK NUTRecommended torque 20Nm
1 2
5 6
HANDLE ALIGNMENT (1G)
3 4
Use Handles to unscrew cartridge.Turn both splines counter clock-wise.
Once cartridge valves are loose, screw them back into the faucet using the handle.Stop when you feel a noticeable resistance.Then remove handles.
Replace Left Handle (hot) one tooth o�from the OFF position as shown.
And Right Handle (cold) one tooth o�from the ON position as shown.
Turn the handles to the desired alignment. (This will unscrew the cartridge)This adjustment should not be more than 25º.
Tighten Lock Nut using 17mm Deep Socket.wrench to secure cartridge valve position.
*Use handle to hold spline while tightening.
RemoveTHREADEDSLEEVE
LOCK NUT
5
WALL MOUNT LAVATORY SET 1GHXL or CWALL MOUNT LAVATORY SET 1GHXL or C
1GR000Wall Mount Valve Rough-In
9Y0HXFA1BFlange
HHX04 Cross Handle
Spout Ring
HHX01Lever Handle
9Y0HXST1ASpout
9YAERSW3AAerator * Turn counter-clock wise to unscrew.
9X0FBHA1EFlange Bushing
1GHXL
1GHXC
CONTACT US: If you need assistance with installation, replacement parts or have any questions regarding your Rubinet product, please call a Customer Service representative at: 905-851-6781 toll free 1-800-461-5901 or visit www.rubinet.com
FEATURES:- Brass construction with choice of 21 finishes- Two Cross or Lever handles- Quarter-turn ceramic disk cartridges- 2.4 gpm @ 60 psi (Helps meet CalGreen regulation)
APPROVAL:- AB1953 / NSF61- ASME A 112.18.1- CSA B125.1
WALL MOUNT LAVATORY SET
ASSEMBLY INSTRUCTION 1GHXL or C
REMOVAL OF FAUCET: Always turn the water supply off before removing the existing faucet or disassembling a valve. Open both faucet handles to relieve water pressure and to ensure that the water has been successfully turned off.
CARE OF FAUCET: The use of warm water and a soft cloth is all that is required to clean Rubinet products. The patina of our living finishes (Oil Rubbed Bronze & Tuscan Brass) will change as a result of normal use. Applying Mineral Oil on occasion will create a softer look, subtle color changes and character.
1609271 3
/8" H
OLES
35
2 1/2" MIN wall limit3 1/8" MAX wall limit
6 9/16"167
ALLO
W 4"
FROM
RIM
OF
FIXT
URE
FINISHED WALL
8"203
2 15/16"75
2 1/2"
