Assembling Assembly station - robotics.ee.uwa.edu.au
Transcript of Assembling Assembly station - robotics.ee.uwa.edu.au
Assembly station Assembly instructions
GB 10/02
Intended use
This station has been developed and produced solely for vocational and further training purposes in the field of automation and communication. The company undertaking the training and/or the instructors is/are to ensure that trainees observe the safety precautions described in the manuals provided.
Festo Didactic herewith excludes any liability for damage or injury caused to trainees, the training company and/or any third party, which may occur if the system is in use for purposes other than purely for training, unless the said damage/injury has been caused by Festo Didactic deliberately or through gross negligence.
Description MONT.ANLEIT
Designation: D:MP-MA-S-MONT-1-GB
Status: 10/2002
Author: Frank Ebel
Graphics: Doris Schwarzenberger, Albert Sigel
Layout: 10/2002
© Festo Didactic GmbH & Co., D-73770 Denkendorf, 2002
Internet: www.festo.com/didactic
e-mail: [email protected]
The copying, distribution and utilisation of this document, as well as the communication of its contents
to others without the express authorisation of Festo Didactic is prohibited. Offenders will be held liable
for the payment of damages. All rights reserved, in particular the right to carry out patent, utility model
or ornamental design registration
2 © Festo Didactic GmbH & Co. • Assembly station
Contents
1. Notes on safety ________________________________________________ 5 2. Short description_______________________________________________ 6 3. Views and tools ________________________________________________ 8 3.1 Views ________________________________________________________ 8 3.2 Required tools _________________________________________________ 9 4. Assembling the station _________________________________________ 10 4.1 Step 1 _______________________________________________________ 10 4.2 Step 2 _______________________________________________________ 11 4.3 Step 3 _______________________________________________________ 12 4.4 Step 4 _______________________________________________________ 13 4.5 Step 5 _______________________________________________________ 14 4.6 Step 6 _______________________________________________________ 15 4.7 Step 7 _______________________________________________________ 16 4.8 Step 8 _______________________________________________________ 17 4.9 Simulation ot the robot cell ______________________________________ 18
© Festo Didactic GmbH & Co. • Assembly station 3
Contents
4 © Festo Didactic GmbH & Co. • Assembly station
1. Notes on safety
In the interests of your own safety, please observe the following safety instructions:
General • Trainees must only work on a station under the supervision of an instructor. • Observe the data in the data sheets for the individual components, particularly
all safety instructions!
Electrical • Electrical connections are to be wired-up or disconnected only when the power
supply is turned off! • Use only extra-low-voltages of up to max. 24 V DC.
Pneumatic • Do not exceed the maximum permissible pressure of 8 bar (800 kPa). • Do not switch on the compressed air supply until you have established and
secured all tubing connections. • Do not disconnect air lines under pressure. • Particular care is to be taken when switching on the compressed air supply.
Cylinders may advance or retract as the compressed air is switched on.
Robotic system • Do not touch any moving part of the robot during operation. Any work within the
operation space must be done after switching off the power. • Do not store a teaching box not connected to the robot control close to the robot
because the built-in EMERGENCY-STOP device is not functional. • If the gripper contains a part during an EMERGENCY-STOP, this will be dropped
during the reset function (nest travel).
Mechanical • Attach all components securely on the mounting plate. • No manual intervention is to take place unless the machine is at rest.
© Festo Didactic GmbH & Co. • Assembly station 5
2. Short description
View of Assembly station
The Assembly station works together with the Robot station.
It supplies the components of the cylinder for the assembly process:
• A double-acting cylinder pushes the cylinder caps out of the cover magazine. • The pistons are available on a pallet. • A double-acting cylinder pushes the springs out of a slim magazine.
The following parts are assembled and fitted by an industrial robot:
• basic body, • piston, • spring and • cover.
Thanks to the use of different basic bodies, it is possible to produce short-stroke cylinders of different piston diameters.
6 © Festo Didactic GmbH & Co. • Assembly station
Short description
The purpose of the Assembly station is
• to supply workpieces to the Robot station
The Assembly station consists of the following:
• Spring magazine module • Slide module • Cover magazine module • Pallet module • Profile plate
• Trolley • Control panel • PLC board
View of Robot station and Assembly station
© Festo Didactic GmbH & Co. • Assembly station 7
3. Views and tools
3.1 Views
Assembly station, plan view
Assembly station, side view
8 © Festo Didactic GmbH & Co. • Assembly station
Views and tools
Assembly station, front view
3.2 Required tools
Tube spanner, 9 x 10
Open ended spanners, 6 x 7, 12 x 13, 22 x 24
Slot-head screwdriver, 3.5
Allen key, 5
© Festo Didactic GmbH & Co. • Assembly station 9
4. Assembling the station
4.1 Step 1
1
10.
9.
8.
7.
6.
5.
4.
3.
2.
1.
11.
12.
13.
14. Nut
1 Profile plate
10 © Festo Didactic GmbH & Co. • Assembly station
Assembling the station
© Festo Didactic GmbH & Co. • Assembly station 11
4.2 Step 2
2.1 (2x)
2.2 (4x)
2.3 (4x)
2.4 (4x) 2.8 (2x)
2.6 (2x)
2.7 (2x)
2.5
2.1 Cable duct
2.2 Socket-head screw
2.3 Washer
2.4 T-head nut
2.5 Top-hat rail
2.6 Socket-head screw
2.7 Washer
2.8 T-head nut
Assembling the station
12 © Festo Didactic GmbH & Co. • Assembly station
4.3 Step 3
2
1.
3.
5.
2 Mounting the electrical system
Assembling the station
© Festo Didactic GmbH & Co. • Assembly station 13
4.4 Step 4
4
3
6
5 (5x)
9.
11.
13.
14.
13.
8
7.
8
7
3 I/O terminal
4 CP valve terminal
5 Cable fixtures (5x)
6 Service unit
7 Palett module
8 Fibre-optic device
9 Fibre-optic device
Assembling the station
14 © Festo Didactic GmbH & Co. • Assembly station
4.5 Step 5
Position of cable fixtures
Assembling the station
© Festo Didactic GmbH & Co. • Assembly station 15
4.6 Step 6
15
10
2.
11 (2x)6.
7.
2.
12
13
14
10.
6.
10 StationLink receiver
11 Connector (2x)
12 Slide module
13 Cover magazine module
14 Spring magazine module
15 StationLink transmitter
Assembling the station
16 © Festo Didactic GmbH & Co. • Assembly station
4.7 Step 7
7.
12.
10.
10.
16 (4x)
16 Cable fixtures (4x)
Assembling the station
© Festo Didactic GmbH & Co. • Assembly station 17
4.8 Step 8
Station fully assembled
Assembling the station
18 © Festo Didactic GmbH & Co. • Assembly station
4.9 Simulation of the robot cell
The robot cell 'Assembly station' is stored in the directory 'Sources\Robot programs\RV-2AJ\Cosimir\Assembly\Assembly.mod' of the CD-ROM supplied. For the simulation of the robot cell you need Cosimir Industrial or Cosimir Professional.