Asgard Annexe Shed Instructions
4
It is always recommended to anchor the unit to the ground. Drill through the four holes in the base of the unit using 6mm dia masonry drill to a depth of 70mm. Screw in the anchor fixings. (These have a self cutting thread). If not anchoring the unit, fit the self seal plugs BEFORE BUILDING to block the fixing holes from underneath. Please note product must be anchored down to comply with LPS1175. TOOLS REQUIRED Power driver POSI-DRIV screwdriver, 6mm dia. masonry drill and a 13mm socket or spanner. ANNEXE ZSCREW32 x4 ZSCREW100 x123 ZSCREW340 x18 32670 x12 6mm Dia. 13mm Spanner 18V ZCOMPPLZS02 x4 ZCOMPPLAS22-23-24 x6 2x 2mm, 2x 3mm, 2x 5mm RH DOOR 32613 x1 LH DOOR 32612 x1 FRT PNL TRAP PLATE 32614 x1 LARGE FRT PANEL 32610 x1 LH SIDE PANEL 32608 x1 RH SIDE PANEL 32609 x1 RH BACK PANEL 32607 x1 LH BACK PANEL 32606 x1 TOP PANEL 32696 x1 BASE PANEL 32605 x1 FASCIA 32611 x1 RAIN GUARD 32615 x1 BASE INSTRUCTIONS Flat and firm base. Recommended: concrete, tarmac or paving flags. Min. distance from walls/ shrubbery: 1000mm. Min. base size (WxDxH) 1990mm x 1100mm x 50mm. LEVELING THE UNIT Correctly level the constructed unit using the shims (ZCOMPPLAS) provided prior to fixing the unit to the ground. Slide the packing pieces under the corners of the unit base as required until an equal gap has been achieved around the door allowing for its smooth operation and alignment. For maintenance instructions of this product visit www.asgardsss.co.uk Warning: some panels may weigh over 20Kg. Beware of manual handling Warning: Please keep this key card safe! Refer to if replacement key is required. x2 Posi-Driv Screwdriver 00001 YOUR UNIQUE KEY CODE
-
Upload
asgard-secure-steel-storage -
Category
Documents
-
view
226 -
download
0
description
For more information please visit www.asgardsss.co.uk
Transcript of Asgard Annexe Shed Instructions
It is always recommended to anchor the unit to the ground. Drill through the four holes in the base of the unit using 6mm dia masonry drill to a depth of 70mm. Screw in the anchor fixings. (These have a self cutting thread). If not anchoring the unit, fit the self seal plugs BEFORE BUILDING to block the fixing holes from underneath. Please note product must be anchored down to comply with LPS1175.
TOOLS REQUIREDPower driver POSI-DRIV screwdriver, 6mm dia. masonry drill and a13mm socket or spanner.
ANNEXE
ZSC
REW
32 x
4
ZSC
REW
100
x12
3
ZSC
REW
340
x18
3267
0 x
12
6mm Dia.
13mm Spanner
18V
ZCO
MPP
LZS0
2 x
4
ZCO
MPP
LAS2
2-23
-24
x6
2x 2
mm
, 2x
3mm
, 2x
5mm
RH
DO
OR
326
13 x
1
LH D
OO
R 3
2612
x1
FRT
PNL
TRAP
PLA
TE 3
2614
x1
LAR
GE
FRT
PAN
EL 3
2610
x1
LH S
IDE
PAN
EL 3
2608
x1
RH
SID
E PA
NEL
326
09 x
1
RH
BAC
K PA
NEL
326
07 x
1
LH B
ACK
PAN
EL 3
2606
x1
TOP PANEL 32696 x1
BASE PANEL 32605 x1
FASCIA 32611 x1
RAIN GUARD 32615 x1
BASE INSTRUCTIONSFlat and firm base. Recommended: concrete, tarmac or paving flags. Min. distance from walls/ shrubbery: 1000mm.Min. base size (WxDxH) 1990mm x 1100mm x 50mm.
LEVELING THE UNITCorrectly level the constructed unit using the shims (ZCOMPPLAS) provided prior to fixing the unit to the ground. Slide the packing pieces under the corners of the unit base as required until an equal gap has been achieved around the door allowing for its smooth operation and alignment.
For maintenance instructions of this product visit www.asgardsss.co.uk
Warning: some panels may weigh over 20Kg. Beware of manual handling
Warning: Please keepthis key card safe! Referto if replacement key is required.
x2
Posi-DrivScrewdriver
00001
YOUR UNIQUEKEY CODE
1
3
5 6
4
2PLEASE NOTE ALL SCREWS ARE FIXED FROM THE INSIDE
RH
SID
E PA
NEL
326
09
RH
BAC
K PA
NEL
326
07
x11
x0x16
LH B
ACK
PAN
EL 3
2606
LH S
IDE
PAN
EL 3
2608
LAR
GE
FRT
PAN
EL 3
2610
ATTACH PANEL 32610 TO LEFT OR RIGHT HAND SIDE TO DETERMINE DOOR LOCATION!
x11
x4
x11
x5x3
x4
x13
BASE PANEL 36443
x5 x8
x16
x11
x5
BASE PANEL 32605 x1
7 8
9 10
11 12
x7
x8
x21
FRT PNL TRAP PLATE 32614
TOP PANEL 32696
RAI
N G
UAR
D 3
2615x8
x7
x3
x4
x4
x12
3267
0 x0
FASC
IA 3
2611
13 14
www.asgardsss.co.uk
x4
32735/11.12.15/KW/REV1
x18
RH
DO
OR
326
13LH
DO
OR
326
12
x3
x3
x3
x3
x3
x3
