ARGtek ARG-1320 QIG

7/28/2019 ARGtek ARG-1320 QIG

1/12

ARGtek Communication Inc. www.argtek.comE-Mail:[email protected] Tel:+ 886-2-2999-6958 Fax :+ 886-2-2999-7742


2/12


Part I: External Installation Direction

Package Content

AP Router 1

DC 12V Power Adapter 1

Antenna 1

Paper QIG 1

Manual/QIG CD 1

Front Panel

LED Light Status Description

ON Router power on.

ON Wireless LAN is active.

Off Wireless LAN is disabled.

Flashing Wireless LAN is sending or receiving data.

ON WAN is connected and active.

Off WAN is disconnected or inactive.

Flashing WAN port is sending or receiving data.

ON Wired LAN port(s) is connected and active.

Off Wired LAN port(s) is disconnected or inactive.

Flashing Wired LAN port(s) is sending or receiving data.


3/12


Rear Panel

Item Description

DC-Jack Power connector, connect to power adapter.

WAN Port Wide Area Network port, for connecting Cable Modem or ADSL

modem.

LAN Port Local Area Network port. Connect your network devices including

computers, printers, game consoles, hubs, or switches.

USB Port Connect your 3G USB modem.

Reset Button Reset router to manufacture default configurations or start WPS

function.

Antenna

ConnectorRP-SMA connector for connecting antenna.

Network Setup


4/12


provides two types of Internet connection:

wireless(3G/3.5G USB modem) or wired (xDSL / cable modem) connection.

You can access internet via USB 3G/3.5G modem card, or via wired xDSL / cable modem

connection. However, only one connection can be used at the same time.You will need to configure your network for the very first time and whenever you want to

change configurations via web interface. To make the network configurations, you have to

connect computer to one of the LAN port and open your web browser.

The AP Router is delivered with the following factory default parameters on the Ethernet LAN

interfaces.

Default IP Address: 10.10.10.254

Default IP subnet mask: 255.255.255.0

Web login User Name: admin

Web login Password: admin

The device has two operation modes (Gateway/Bridge).

The default IP addresses for the device are 10.10.10.254,

so you need to make sure the IP address of your PC is in the same subnet as the device,

such as 10.10.10.X.

It will take about 55 seconds to complete the boot up sequence after power on.

You can refer to user manual for the details of how to configure your network.


5/12


Part II: Internal Web Management

AP Model Setup (ADSL)

1 Install the antenna & power adapter, and then connect the LAN cable with LAN port of

this equipment. Another side of cable line connects with network card of computer.

Waiting for booting around 20 seconds.

2 Open the IE ( Internet Explorer) and type 10.10.10.254 on Website to enter the setup

frame. If you cant enter to setup frame, you can try to set the IP address for

10.10.10.XXX and try to connect again. Otherwise, please press Reset button around 10

seconds to restore AP and try to enter again

Select the Operation Mode on the left side of setup frame

1. In Operation Mode, select Gateway and press Apply


6/12


2a. In Internet Settings / WAN /, select PPPoE (ADSL) for your WAN Connection Type and

enter your User Name & Password which were presented by your ISOP company. And

then press Apply

2b. In Internet Setting/LAN/, you may change the setting of IP address, DHCP and etc. then

press Apply

3. In Wireless Settings / Basic, you may change the setting of SSID, and then press Apply


7/12


4. In Wireless Settings / Security, you may change the setting of password, and then press

Apply

Finish setting and press Apply, the setting will be completed after rebooting around 20

seconds.

Note: You have to connect ADSL cable with WAN port of this equipment.

==============================================================


8/12


AP Model Setup (IP Share)

1 Install the antenna & power adapter, and then connect the LAN cable with LAN port of

this equipment. Another side of cable line connects with network card of computer.

Waiting for booting around 20 seconds.2 Open the IE ( Internet Explorer) and type 10.10.10.254 on Website to enter the setup





1. In Operation Mode, please select Bridge. Select AP or Main AP in Wireless Operation

Mode and press Apply


9/12


2. In Internet Setting/LAN/, you may change the setting of IP address, DHCP and etc. then

press Apply



Apply


seconds.

tNote: You have to connect cable line with LAN port of this equipmen


10/12


.

3G Model Setup (3G Network Card)

1 Install the antenna & power adapter & your 3G network card in USB port of this

equipment, and then connect the LAN cable with LAN port of this equipment. Anotherside of cable line connects with network card of computer. Waiting for booting around

20 seconds.

2 Open the IE ( Internet Explorer) and type 10.10.10.254 on Website to enter the setup





1. In Operation Mode, please select Gateway. And then press Apply


11/12


2a. In Internet Settings / WAN /, select 3G Mode for your WAN Connection Type and choice

your USB 3G modem type. And then press Apply

2b. In Internet Setting/LAN/, you may change the setting of IP address, DHCP and etc. then

press Apply



12/12

ARGtek Communication Inc. www.argtek.comE-Mail:sales@argtek com Tel:+ 886-2-2999-6958 Fax :+ 886-2-2999-7742


Apply


seconds.

Note: You have to connect cable line with LAN port of this equipment.

=============================================================

ARGtek ARG-1320 QIG

Documents

Transcript of ARGtek ARG-1320 QIG