ARCHITECTURAL STRUCTURES FORM, B DESIGN ARCH...

1

F2009abn

twenty two

concrete construction:

flat spanning systems, columns & frames

ARCHITECTURAL STRUCTURES:

FORM, BEHAVIOR, AND DESIGN ARCH 331

DR. ANNE NICHOLSSUMMER 2014

Concrete Spans 1Lecture 22

Architectural StructuresARCH 331

lecture

http:// nisee.berkeley.edu/godden

Concrete Spans 2

Lecture 25

Foundations Structures

ARCH 331

F2008abn

Reinforced Concrete Design

• economical & common

• resist lateral loads

Concrete Spans 3

Lecture 25


ARCH 331

F2008abn


• flat plate

– 5”-10” thick

– simple formwork

– lower story heights

• flat slab

– same as plate

– 2 ¼”–8” drop panels

Concrete Spans 4

Lecture 25


ARCH 331

F2008abn


• beam supported

– slab depth ~ L/20

– 8”–60” deep

• one-way joists

– 3”–5” slab

– 8”–20” stems

– 5”-7” webs

The Architect’s Studio Companion

2

Concrete Spans 5

Lecture 25


ARCH 331

F2008abn


• two-way joist

– “waffle slab”

– 3”-5” slab

– 8”-24” stems

– 6”-8” webs

• beam supported slab

– 5”-10” slabs

– taller story heights

F2008abnConcrete Spans 6Lecture 25

Foundations Structures ARCH 331


• simplified frame analysis

– strips, like

continuous beams

• moments require flexural reinforcement

– top & bottom

– both directions of slab

– continuous, bent or

discontinuous

Concrete Spans 7

Lecture 25


ARCH 331

F2008abn


• one-way slabs (wide beam design)

– approximate analysis for moment & shear

coefficients

– two or more spans

– ~ same lengths

– wu from combos

– uniform loads with L/D ≤ 3

– � n is clear span (+M) or average of

adjacent clear spans (-M)

Concrete Spans 8

Lecture 25


ARCH 331

F2008abn


3

Concrete Spans 9

Lecture 25


ARCH 331

F2008abn


• two-way slabs - Direct Design Method

– 3 or more spans each way

– uniform loads with L/D ≤ 3

– rectangular panels with

long/short span ≤ 2

– successive spans

can’t differ > longer/3

– column offset no more

than 10% span

Concrete Spans 10

Lecture 25


ARCH 331

F2008abn




Shear in Concrete

• at columns

• want to avoid stirrups

• can use shear studs or heads

Concrete Spans 12

Lecture 25


ARCH 331

F2008abn

Shear in Concrete

• critical section at d/2 from

– column face, column capital or drop panel

4

F2008abnConcrete Spans 13

Lecture 25


ARCH 331

Shear in Concrete

• at columns with waffle slabs


Concrete Spans 14

Lecture 25


ARCH 331

F2008abn

Openings in Slabs

• careful placement of holes

• shear strength reduced

• bending & deflection canincrease

Concrete Spans 15

Lecture 25


ARCH 331

F2008abn

General Beam Design

• f’c & fy needed

• usually size just b & h

– even inches typical (forms)

– similar joist to beam depth

– b:h of 1:1.5-1:2.5

– bw & bf for T

– to fit reinforcement + stirrups

• slab design, t

– deflection control & shear6

2bhS =

Concrete Spans 16

Lecture 25


ARCH 331

F2008abn

General Beam Design (cont’d)

• custom design:

– longitudinal steel

– shear reinforcement

– detailing

5

Concrete Spans 17

Lecture 25


ARCH 331

F2008abn

Space “Frame” Behavior

• handle uniformly distributed loads well

• bending moment

– tension &

compression

“couple” with

depth

– member sizes

can vary,

but difficult

Concrete Spans 18

Lecture 25


ARCH 331

F2008abn

Space “Frame” Behavior

• shear at columns

• support conditions still important

– point supports not optimal

• fabrication/construction can dominate design

Concrete Spans 19

Lecture 25


ARCH 331

F2008abn

Folded Plates

• increased bending stiffness with folding

• lateral buckling avoided



Folded Plates

• common for roofs

• edges needstiffening


6


Architectural Structures ARCH 331

Folded Plates

– State Farm Center(Assembly Hall), University of Illinois

– Harrison & Abramovitz 1963

– Edge-supported dome spanning 400 feet wound with 614 miles of one-fifth inch steel wire

www.library.illinois.edu

F2008abnConcrete Columns 2

Lecture 26


ARCH 331

Concrete in Compression

• crushing

• vertical cracking

– tension

• diagonal cracking

– shear

•cf ′

http://www.bam.de

Concrete Columns 3

Lecture 26


ARCH 331

F2008abn

Columns Reinforcement

• columns require

– ties or spiral reinforcement

to “confine” concrete

(#3 bars minimum)

– minimum amount of longitudinal steel

(#5 bars minimum: 4 with ties, 5 with spiral)

Concrete Columns 4Lecture 26


F2008abn

Slenderness

• effective length in monolithic with

respect to stiffness of joint: Ψ & k

• not slender when

22<r

kLu

7



F2008abn

Effective Length (revisited)

• relative rotation

b

c

lEI

lEI

Σ

Σ=Ψ

Concrete Columns 6

Lecture 26


ARCH 331

F2008abn

Column Behavior

F2008abnConcrete Columns 7Lecture 26


Column Design

• φc = 0.65 for ties, φc = 0.75 for spirals

• Po – no bending

• Pu ≤ φcPn– ties: Pn = 0.8Po– spiral: Pn = 0.85Po

• nominal axial capacity:

– presumes steel yields

– concrete at ultimate stress

stystgco AfAAfP +−′= )(85.0



F2008abn

Columns with Bending

• eccentric loads can cause moments

• moments can change shape and induce more deflection

(P-∆)P

∆

8



F2008abn


• for ultimate strength behavior, ultimate strains can’t be exceeded

– concrete 0.003

– steel

• P reduces with M

s

y

E

f

F2009abn


• need to consider combined stresses

• linear strain

• steel stress at or below fy

• plot interactiondiagram

Concrete Columns 10

Lecture 26


ARCH 331

Concrete Columns 11

Lecture 26


ARCH 331

F2008abn

Design Methods

• calculation intensive

– handbook charts

– computer programs

Concrete Columns 12

Lecture 26


ARCH 331

F2008abn

Design Considerations

• bending at both ends

– P- ∆ maximum

• biaxial bending

• walls

– unit wide columns

– “deep” beam shear

• detailing

– shorter development lengths

– dowels to footings

ARCHITECTURAL STRUCTURES FORM, B DESIGN ARCH...

Documents

Transcript of ARCHITECTURAL STRUCTURES FORM, B DESIGN ARCH...