Architectural Interior Wall Paneling Interior Wall Paneling. Compact Laminate Arpa Compact Laminate...
Transcript of Architectural Interior Wall Paneling Interior Wall Paneling. Compact Laminate Arpa Compact Laminate...
ArchitecturalInterior Wall Paneling
Compact Laminate
Arpa Compact Laminate is comprised of reinforced wood fibres and thermosetting resins which when manufactured under very high pressure and heat produce a homogenous, non porousand extremely strong material. The surface of compact laminate is achieved through a decorativepaper impregnated with melamine which gives it an extremely high wear and scratch resistant property.
Because of it’s particular material makeup and mechanical properties, Compact Laminate has the following attributes:
Impact Resistant - because of it’s solid core and hard surface, this material is a goodchoice for surfacing, wall cladding and case work that needs to be durable.
Scratch resistant - the melamine surface provides excellent scratch resistance even inheavy duty use and high traffic areas.
Wear resisant - this surface is durable and long lasting: ideal even when frequent clean-ing is required.
Non-porous - since Compact Laminate has a sealed non- porous surface, it is hygenic, chemically resistant and not affected by moisture.
Extreme Temperature Resistant - Arpa Compact Laminate is not affected by temperaturesranging from -20 to 280 degrees F.
Structural Strength - Due to it’s high flexural rigidness, Arpa’s Compact Laminate is highlysuited for self supporting applications.
Open Reveal Captured Shadowline
Architectural Interior Panels and Fastening Systems
Sheet Size - Panels are custom fabricated to meet the design needs of each project’s requirements. Maximum size 51” x 120“ Thickness - 8 mm (.31”) Finish (Surface Texture) - Standard Finishes - matte (erre), gloss, and pesca.
Fire Rating Class B - Availability dependant upon local code requirements.Pattern availability - Most of Arpa’s thin laminate patterns are available. Check the
“Wall Panel” sample chain, “Wall Panel” patterns selection sheet, or contact your local Arpa sales representative for information.
The “open reveal”system featuresa 1/4” channelat all joint areas.Perfect for the designer looking
with elegantdetailing.
Available in satin,black, gold and
The “captured system”features a closededge. It is ideallysuited for hospitalsand other high
where cleanlinessis of utmost concern.
Available in satin,black, gold and
The “shadowlinesystem” featuresa narrow edge and joint reveal that creates a slightshadow betweenthe panels and theextrusion for asubtle, upscale look.
Available in satin,gold, black and
Arpa has been manufacturing high pressure laminates for over 50 years and is recognized as a design innovator. With distribution andsales representation globally, Arpa can handle any project regardless of its scope or location.
and abstract patterns. Combined with a broad range of available textures the designer has virtually unlimited possibilities.
For technical assistance or additional information contact Arpa USA or your local Arpa sales representative.
Arpa USA Inc. 13300 Vantage Way, Jacksonville, Fl 32218 tel 877-277-2669 email [email protected] www.arpausa.com
0001 0004 0010 0011 0020 0200 0201 0202 0203 0204 0205 0206 0210 0211 0214
0215 0218 0227 0234 0237 0242 0244 0247 0248 0256 0257 0264 0500 0509 0510
0511 0515 0517 0523 0526 0527 0530 0531 0533 0534 0535 0536 0538 0542 0543
0549 0566 0553 0559 0561 0562 0564 0565 0569 0570 0571 0573 0576 0589 0593
0594 0595 0605 0606 0607 0608 0610 0614 0619 0621 0622 0623 0624 0627 0634
0636 0637 0638 0639 0640 0641 0643 0644 0647 0648 0649 0651 0654 0658 0659
0660 0661 0662 0663 0664 0665 0666 0669 0670 0672 0673 0675 0677 0679 0682
0685 0689 0690 0691 0692 0997 0998 1017 1086 1856 1857 1858 1859 1860 1861
Colors and Patterns
1862 1864 1869 1902 1903 1905 1907 1908 1909 1910 1911 1958 1961 1975 1986
Colors and Patterns
1993 1994 2002 2511 2512 2516 2523 2527 2536 2541 2543 2550 2551 2553 2557
2558 2569 2571 2572 2573 2574 2575 2576 2577 2578 2591 2593 2594 2595 2596
2600 2601 2606 2607 2608 2609 2610 2611 2612 2613 2614 2615 3072 3099 3112
3118 3135 3139 3141 3151 3175 3190 3191 3192 3193 3276 3279 4070 4098 4123
4129 4197 4198 4201 4202 4203 4205 4206 4207 4264 4266 4267 4268 4303 4306
4318 4319 4321 4322 4329 4350 4379 4384 4390 4396 4397 4416 4417 4419 4445
4450 4451 4452 4471 4472 7360 7361 7363 9204 9205 9206 9208 9209 9214 9215
9216 A034 A035 A036 A067 A068 A069 A070 A071 A072 A073 A074 A075 A076 A077
A078 A079 A080 A081 A082 A083 A084 A085 A086 A087
Fixed and sliding points have to be formed (Fig. 15.)
Sliding pointThe diameter of the drill hole in ARPA (BG) must be drilledlarger than the diameter of the fastening, depending on therequired expansion clearance. This is the shaft diameter of thefastening plus 2 mm (.08”) for every meter of cladding material startingfrom the fixed point. The head of the fastening must be bigenough so that the drill hole in ARPA (BG) is always covered.The fastening is placed in such a way that the panel can move.Rivets are put in place with flexible mouth-pieces. The definedclearance of the rivet head to the surface of the panel (0.3 mm,.01”)allows movement of the element in the drill hole.
Screws must not be over-tightened. Do not use any countersunkscrews - use washers if necessary. The center point of the drillhole in the subconstruction must coincide with the centre point ofthe drill hole in the ARPA (BG) panels. Drill with a centeringpiece. The fastenings should be put in place starting from themiddle of panel outwards.
Fixed pointFixed points are used for uniform distribution (halving) of theexpansion and shrinkage movements. The diameter of the drillhole in ARPA (BG) is the same size as the diameter of thefastening.
Edge spacingsFor reasons of stability and flatness, the edge spacings must bekept to without fail. The joints must be made at least 8 mm (5/16”) wide so that changes in size can take place without hindrance.
Fastening SpacingsThese are to be chosen in accordance with the structuralengineering requirements (calculations) or, if this is not necessarydue to the local regulations, according to the following table. Inthe edge region of the construction, the spacings of the fasteningsare to be chosen smaller than in the central region (pressure,suction).
Panel thickness
6 mm
8 mm
10 mm
Maximum fasteningspacing “b”Single span panel
400mm (16”)
600 mm (24”)
700 mm (28”)
Maximum fasteningspacing “a“Double span panel
500 mm (19”)
700mm (28”)
850 mm (34”)
For installation with mechanical fastenings
Fixed point Sliding point Space from edge
2-3”
2-3”
20mm(.75”)20aa
a
a
a
a
a
2-3”
2-3”
20mm(.75”)20b
a
a
a
a
a
≥
Double span panelSingle span panel
tnioj lacitrev fo elpmaxE
ARPA (BG) panels can be mounted using screws or rivets on an aluminium substructure, or with screws on a wood framework. An aluminiumsubstructure consists of vertical support profiles which are secured to the wall using angle brackets. A wooden substructure consists ofslats fitted to durable studs secured to the wall. Due to the material properties of ARPA (BG) , fixed points and sliding points need tobe made to mount the panels (Fig. 15 and Fig. 16).
*
(5/16”)
Visable Mechanical Fastening
Visable Fastening With Screws on a Timber Batten
3/4”- 1,1/2”
1/8”
External Corner Profile
(Optional)
Vertical Timber Batten
Color Coated Screws to Match Panel
Arpa Panel
2-3mm Space Between Paneland Screw to Allow For Expansion/Contraction
Horizontal Joint Detail
1/8”-3/8”
Arpa Panel
1/2”- 1,1/2”
Structure Wall Substrate
Vertical Timber Battens
Color Coated Screws to Match Panel 2-3mm Space Between Panel andScrew to Allow For Expansion/Contraction
Visable Fastening With Screws on a Timber Batten
,1/2
”1-
1/2”
Intermediate Support Detail
Vertical Timber BattenIntermediate Support
Color Coated Screws to Match Panel
Arpa Panel
2-3mm Space Between Panel andScrew to Allow For Expansion/Contraction
Vertical Panel Joint Detail
Arpa Panel
1/8”-3/8”
Vertical Timber Batten
Color Coated Screws to Match Panel
2-3mm Space Between Panel andScrew To Allow For Expansion/Contraction
Gluing*An alternative to fastening with mechanical means is gluing the ARPA (BG) wall panels* with the adhesive and tape gluing system.
works on normal planed wood or aluminium subconstructions.Gluing is a clean and simple solution for vertical wall panel systems,ceilings reveals and much more.
For proper structural bonding, Arpa wall panels are designed to beused with the proper wall cladding adhesive.
by the adhesive manufacturer must be strictly complied with toensure proper bonding.**
Advantages of the adhesive gluing system:
Excellent appearance - no fastening elements can be seen from the front
Simple, economical and fast installation
Tough, movement-absorbing fastening
Panel thickness
6 mm (1/4”)
Maximum fastening spacingSingle span panel
450 mm (18”)600 mm (24”)650 mm (26”)
Maximum fastening spacingDouble span panel
550 mm (22”)650 mm (26”)650 mm (26”)
For glued installation with adhesive (spacing of the verticalsupport construction)
Installation
foamtape------------------9mm(3/8”)-------------adheasivebead
span foradhesive application
Vertical ------------Profiles
BG Panels------
------------- ^Profile SpanSee Chart below
Compressed------Bead
Single Span Multispan
Profile Width 80-100mm(3-4”)----------------------------
>
--------------
>
Attachment/Bonding Diagram
Typical Installation Diagram
> Profile width 45mm(1.75”)
8 mm (5/16”)10 mm (3/8”)
Non Visable Adhesive Fastening
*Not re commended for pattern 2002OP
75 lbs. psf holding strength
**Failure to use the correct fasteners or adhesive, or to strictly follow the correct installation procedures as required by the adhesive/fastener manufacturer,may result not only in the voidance of the product warranty but may result in potential panel detachment causing personal injury, death or property damage.
Open Reveal Captured Shadowline
Architectural Interior Panels and Fastening Systems
Sheet Size - Panels are custom fabricated to meet the design needs of each project’s requirements. Maximum size 51” x 120“ Thickness - 8 mm (.31”) Finish (Surface Texture) - Standard Finishes - matte (erre), gloss, and pesca.
Fire Rating Class B - Availability dependant upon local code requirements.Pattern availability - Most of Arpa’s thin laminate patterns are available. Check the
“Wall Panel” sample chain, “Wall Panel” patterns selection sheet, or contact your local Arpa sales representative for information.
The “open reveal”system featuresa 1/4” channelat all joint areas.Perfect for the designer looking
with elegantdetailing.
Available in satin,black, gold and
The “captured system”features a closededge. It is ideallysuited for hospitalsand other high
where cleanlinessis of utmost concern.
Available in satin,black, gold and
The “shadowlinesystem” featuresa narrow edge and joint reveal that creates a slightshadow betweenthe panels and theextrusion for asubtle, upscale look.
Available in satin,gold, black and
Arpa has been manufacturing high pressure laminates for over 50 years and is recognized as a design innovator. With distribution andsales representation globally, Arpa can handle any project regardless of its scope or location.
and abstract patterns. Combined with a broad range of available textures the designer has virtually unlimited possibilities.
For technical assistance or additional information contact Arpa USA or your local Arpa sales representative.
Arpa USA Inc. 13300 Vantage Way, Jacksonville, Fl 32218 tel 877-277-2669 email [email protected] www.arpausa.com
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa
Arpa