(732) 938-2000 / 800-LAB-VOLT, FAX: (732) 774-8573, E-MAIL: us@labvolt.com(418) 849-1000 / 800-LAB-VOLT, FAX: (418) 849-1666, E-MAIL: ca@labvolt.com

INTERNET: http://www.labvolt.com

8092 – shown with computer, not included

ATelecommunications ANTENNA TRAINING AND

MEASURING SYSTEMMODEL 8092

GENERAL DESCRIPTIONThe Lab-Volt Antenna Training and Measuring System(ATMS), Model 8092, provides teachers and studentswith training materials for hands-on experimentation onantennas in the 1-GHz and 10-GHz bands. A convenientand powerful antenna measuring system, the ATMS canalso be utilized by design and research teams.

The ATMS includes a set of 1-GHz antennas, a setof 10-GHz antennas, an RF Generator, a receivingsystem, and the Lab-Volt Data Acquisition andManagement software for Antennas (LVDAM-ANT), auser-friendly software operating under the Microsoft®

Windows™ environment. The receiving system consistsof a rotating Antenna Positioner linked to a DataAcquisition Interface connected to the USB port of aPentium-type personal computer (to be purchasedseparately).

The ATMS is designed for low-power safe operation,both in the 1-GHz and 10-GHz bands, allowingmeasurement of antenna characteristics in these bands.The Data Acquisition Interface controls the AntennaPositioner and acquires the signal received from theantenna under test.

The LVDAM-ANT software provides a toolbox forcontrolling antenna rotation and data acquisition, and fordisplaying measured antenna characteristics in the E andH planes. Different forms of 2 D and 3 D representationsare available from the results of the E- and H-planepattern measurements as shown in Figures 1 to 5 on thenext pages. The LVDAM-ANT software also includesalgorithms for estimating the beamwidth and directivityof antennas from measurements.

The ATMS is a self-contained, stand-alone systemthat does not require other microwave equipment.However, optional antennas, a two element phasing kit,and a set of RCS demonstration accessories can beadded to the ATMS in order to enhance the scope ofexperimentation on antennas and reflectors. Thesepieces of optional equipment are listed and described inthe Optional Equipment and Optional EquipmentDescription sections of this data sheet. Furthermore, theATMS is compatible with the Lab-Volt 10.5-GHzMicrowave Technology Training System, Model 8090.The VSWR Meter and the Power Meter of the Lab-Volt

ANTENNA TRAINING AND MEASURING SYSTEMMODEL 8092

2

Figure 1. The E-plane and the H-plane patterns are acquiredseparately. These patterns can be plotted on a polar graph (asshown in figure) or a Cartesian graph (see Figure 2).

Figure 2. E- and H-plane patterns of an helical antenna plotted ona Cartesian coordinate graph.

Figure 3. The acquired E- and H-plane patterns can be displayedsimultaneously on a tri-dimensional (3D) display (shown in figure:dipole antenna pattern).

Microwave Technology Training System, along withmicrowave components such as the slotted line, the Gunnoscillator, attenuators, and couplers, can be put to usefor various creative laboratory projects.

(continues on next page)

TABLE OF CONTENTSGeneral Description . . . . . . . . . . . . . . . . . . . . . . . . . 1Table of Contents of the Student Manual . . . . . . . . . 3List of Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Optional Equipment . . . . . . . . . . . . . . . . . . . . . . . . . 4Module Description . . . . . . . . . . . . . . . . . . . . . . . . . . 5Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Optional Equipment Description . . . . . . . . . . . . . . . . 8Other Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Personal Computer Requirements . . . . . . . . . . . . . 13Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Ordering Numbers . . . . . . . . . . . . . . . . . . . . . . . . . 15

1 The ordering numbers shown apply to the English 120-V version. Other versions are available. Refer to the Ordering Numbers section.

3

Figure 4. The acquired E- and H-plane patterns can be displayedsimultaneously on a tri-dimensional (3D) display (shown in figure:helical antenna pattern).

Figure 5. The E- and H-plane patterns can also be combined toproduce a full 3D radiation pattern (shown in figure: dipoleantenna pattern).

GENERAL DESCRIPTION (cont’d)

TABLE OF CONTENTS OF THE STUDENT MANUALAntenna Fundamentals (30857-00)C Basic Antenna Measurements

– Radiation Pattern of a λ/2 Dipole at 1 GHz– Radiation Pattern of an Open Waveguide at,

10 GHz– Gain of Pyramidal Horn Antennas– Experiments with λ/2, λ, and 3λ/2 Dipoles– Half Wave Folded Dipole Antennas and

Impedance Transformation with Baluns

C Experimentation with Different Antenna Types– Monopole Antennas– Loop Antennas– Circular Polarization and Helical Antennas– Parasitic Array (Yagi-Uda) Antennas

C Microstrip and Array Antennas– Antenna Arrays: The Slot Antenna– Microstrip Technology: The Rectangular Patch

Antenna– Microstrip Planar Array Antennas

LIST OF EQUIPMENTQTY DESCRIPTION ORDERING NUMBER1

1 RF Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9505-001 Antenna Positioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9506-001 Data Acquisition Interface / Power Supply (includes system user guide, no. 30857-E0) . . . . . . . . . . 9507-301 Horn Antenna, Small Aperture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9535-A02 Horn Antenna, Large Aperture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9550-002 Helical Antenna, Right-Hand Circular Polarization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9551-001 Helical Antenna, Left-Hand Circular Polarization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9552-001 Patch Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9553-001 Multi-Slotted-Waveguide Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9554-00

ANTENNA TRAINING AND MEASURING SYSTEMMODEL 8092

2 The ordering numbers shown apply to the English 120-V version. Other versions are available. Refer to the Ordering Numbers section.3 When ordering the optional RCS Demonstration Accessories, Model 9594-B0, the Antenna Positioner, Model 9506-A0, is required instead of the conventional Antenna Positioner, Model 9506-00.

An upgrade kit (part number 39378) is available to convert the conventional Antenna Positioner, Model 9506-00, into a 9506-A0 Antenna Positioner. See OPTIONAL EQUIPMENT DESCRIPTIONin this data sheet for additional information.

4

LIST OF EQUIPMENT (cont’d)QTY DESCRIPTION ORDERING NUMBER2

1 Open-Ended Waveguide Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9555-001 Yagi Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9560-001 Wire Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9561-001 Cables and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9594-101 Waveguide Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9594-A01 Antenna Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9595-001 Storage Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9598-001 Antenna Fundamentals (student manual) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30857-001 Antenna Fundamentals (instructor guide) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30857-10

OPTIONAL EQUIPMENTDESCRIPTION ORDERING NUMBER2

Antenna Positioner (for RCS Demonstration) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9506-A03

Directional Coupler, 1 GHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9529-00Multi-Beam Array Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9556-00Log-Periodic Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9562-00Two Element Phasing Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9563-00RCS Demonstration Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9594-B03

Parabolic Reflector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9596-00The Multi-Beam Array Antenna (student manual) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33458-00Two Element Phasing Kit Instructions (instruction sheet) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35166-E0

5

MODULE DESCRIPTIONModel 9505 – RF Generator

The RF Generator contains two independent generatorscapable of producing a CW or 1-kHz square wave AMmodulated RF signal at 915 MHz and 10.5 GHz. Eachgenerator has a push-button switch for turningRF power on and off, a LED that flashes on and offwhen RF power is turned on, and an SMA outputconnector. The oscillator in the 915-MHz generator canbe tuned from 700 to 1200 MHz via an external tuningvoltage input. All outputs are fully protected againstshort-circuits and misconnections. The RF Generatoris self-powered and has a Lab-Volt standardunregulated DC power bus to supply power to othercompatible modules through its top panel connector.The unit beeps when RF power is turned on to helpavoiding interference and to warn students in thelaboratory that RF power is being emitted.

Model 9506 – Antenna Positioner

The Antenna Positioner consists of the mast for thereceiving antenna (antenna under test), a drive motor,a signal detector, a variable attenuator, and a shaftencoder. The drive motor is used to rotate the mastwhile the rotation is controlled by the LVDAM-ANTsoftware via the Data Acquisition Interface. An SMAconnector, mounted on the base of the mast, allows aconnection to be made between the receiving antennaand the signal detector. This detector provides a signalwhose voltage depends on the level of the RF signalreceived. This signal is available on a BNC connectorfor connection to the Data Acquisition Interface.

The variable attenuator allows adjustments to bemade to the sensitivity of the receiving systemaccording to the strength of the received signal, in orderto prevent system saturation. This attenuator iscontrolled by the LVDAM-ANT software via the DataAcquisition Interface. The shaft encoder is coupled withthe shaft of the drive motor and provides signals tomonitor the rotation of the mast. Two multi-pinconnectors on the Antenna Positioner allow connectionto the Data Acquisition Interface / Power Supply .

ANTENNA TRAINING AND MEASURING SYSTEMMODEL 8092

6

Model 9507-3 – Data Acquisition Interface /Power Supply

The Data Acquisition Interface links the Antenna Posi-tioner with the personal computer that runs theLVDAM-ANT software. The link to the computer isachieved through a USB port connector mounted on therear panel of the module. The Data Acquisition Interface

converts the received signal coming from the AntennaPositioner into a digital signal which can be used by thecomputer. It also routes the shaft encoder signalscoming from the Antenna Positioner to the computerand provides the signals required to control the drivemotor and the variable attenuator in the AntennaPositioner. A BNC connector and a multi-pin connectorallow connection of the Data Acquisition Interface to theAntenna Positioner.

The Power Supply, which provides regulated DCpower to the Data Acquisition Interface, has a Lab-Voltstandard unregulated DC power bus to supply powerto other compatible modules through its top panelconnector. The unregulated DC power bus suppliespower to the Antenna Positioner through a multi-pinconnector mounted on the front panel of the module.The Power Supply also provides AC power to the drivemotor in the Antenna Positioner through this multi-pinconnector. An illuminated power switch allows thePower Supply to be turned on and off.

ANTENNASThe ATMS provides a great variety of 1-GHz and 10-GHz antennas. With the exception of the horn- and waveguide-typeantennas, connection to each antenna is made through an SMA connector. The 1-GHz and 10-GHz antennas availablein the ATMS are listed below:

1-GHz AntennasC Dipoles (λ/2, λ, 3λ/2)C Folded DipoleC Folded Dipole with BalunC Monopole (over ground plane)C Drooping MonopoleC Loops (circular, square, lozenge)C Fixed YagiC Adjustable Yagi

10-GHz AntennasC Open-Ended WaveguideC Slotted Waveguide (single and multi-slots)C Horns (small and large aperture)C Helical (right-hand and left-hand circular

polarization)C Patch (rectangular, parallel-fed array, series-fed

array)

7

The following figures show polar plots of the radiation patterns of the folded dipole and slotted-waveguide antennas,obtained using the ATMS.

Folded Dipole Antenna Slotted-Waveguide Antenna

Radiation patterns

ANTENNA TRAINING AND MEASURING SYSTEMMODEL 8092

8

RCS pattern of a small metal plate obtained using the ATMS.

ATMS ready to measure the RCS of a metal plate. Notice theconnection of a second horn antenna to the auxiliary RF input ofthe optional Antenna Positioner, Model 9506-A

OPTIONAL EQUIPMENT DESCRIPTIONModel 9506-A – Antenna Positioner

This variant of the Antenna Positioner is provided with anauxiliary RF input coupled to an RF signal detector.These additional components are required when theATMS is used with the optional RCS DemonstrationAccessories, Model 9594-B0, to measure and observethe near-field or far-field relative Radar Cross Section(RCS) of reflecting objects (targets). RCS patterns oftargets with different shapes are acquired, displayed, andstored using the LVDAM-ANT software the same way asantenna radiation patterns are (see figure). The ATMSand RCS Demonstration Accessories allow quasi-monostatic and bi-static RCS measurements to beperformed. The standard Antenna Positioner,Model 9506, is no longer required when the AntennaPositioner, Model 9506-A, is ordered.

A switch on the front panel of the Antenna Positionerallows selection between the RF input mounted on thebase of the rotating mast and the auxiliary RF input.

Model 9594-B – RCS Demonstration Accessories

This kit contains all the accessories required to measurethe relative RCS pattern of targets using the ATMS. Itincludes targets of various shapes (small and large metalplates, cylinder, and prism-shaped target), a 2 m SMAcable, a fixed antenna support, and an antenna mountingpole.

9

MBAA radiation pattern obtained using the ATMS when twobeams are simultaneously excited.

Model 9556 – Multi-Beam Array Antenna

The Multi-Beam Array Antenna (MBAA) is designed tooperate in the X frequency band (8 to 12.4 GHz) andprovides students with training in phased array antennatheory. It allows hands-on experimentation in advancedantenna principles used in the fields of radar imagery aswell as satellite and space-diversity communicationsystems.

The MBAA uses a microstrip Rotman lens to modifythe phase shifts to a linear array of radiating elements.The antenna beam can be steered to various discretedirections by manually switching the connection to oneof the MBAA RF port connectors. The MBAA can also beoperated with multiple beams (2) by using the includedpower combiner. The MBAA is mechanically designed toprovide easy installation on the ATMS AntennaPositioner. The student manual included with the MBAAdeals with the multi-beam array antenna theory anddesign, antenna beam characteristics, and beamcombination effects.

ANTENNA TRAINING AND MEASURING SYSTEMMODEL 8092

10

Two drooping monopole antennas installed on the ATMS AntennaPositioner ready for experimenting the effects of antennaphasing.

Model 9562 – Log-Periodic Antenna

The Log-Periodic Antenna is designed to familiarizestudents with the principles of frequency independentantennas. The nominal frequency range of the Log-Periodic Antenna is 700 to 3600 MHz, but it can beoperated from 700 to 1200 MHz when used with theATMS (by tuning the frequency of the ATMS 1-GHz RFGenerator). The antenna can be mounted to the ATMSAntenna Positioner for either vertical or horizontalpolarization. For full flexibility in experimenting with thisantenna, it is recommended that two are used, one fortransmission and one for reception.

Model 9563 – Two Element Phasing Kit

The Two Element Phasing Kit enables students toobserve the effects of antenna phasing on the resultingantenna radiation pattern (combined radiation pattern).Different combined radiation patterns such as end-fire,broadside, and cardioid can be obtained. These can bemeasured, stored, and analyzed using the ATMS.

The Two Element Phasing Kit consists of anadditional drooping monopole antenna (one is alreadyincluded in the ATMS), an additional antenna mast withvertical mounting clips (one is already included in theATMS), a power splitter/combiner, and a set of RF cablesof different lengths. Phase shifts of 0, 90, and 180degrees can be produced with the supplied RF cables.Other phase shifts can be produced by using RF cableshaving lengths that differ from those of the supplied RFcables.

11

Model 9596 – Parabolic ReflectorThe Parabolic Reflector allows students to study thecharacteristics of the parabolic antenna, one of today'smost widely used antennas, that finds applications incellular telephony, satellite communications, radars, etc.

The Parabolic Reflector mainly consists of a parabolicreflector and a chassis. It allows a complete parabolicantenna to be assembled using the small-aperture hornantenna included in the ATMS. A mast included in theParabolic Reflector allows the assembled parabolicantenna to be installed on the ATMS Antenna Positioner.This mast also allows the parabolic antenna to be tilted90E for either vertical or horizontal polarization.

ANTENNA TRAINING AND MEASURING SYSTEMMODEL 8092

12

OTHER HARDWAREModel 9594-1 – Cables and Accessories

This kit contains the cables necessary for theinterconnection of the modules in the ATMS. The kitincludes SMA connector coaxial cables (flexible) ofdifferent lengths for the RF connections, as well as a90E adapter required when using the adjustable Yagiantenna and patch antennas. A plastic case is suppliedfor storage.

Model 9594-A – Waveguide Accessories

This kit contains the accessories required when usingthe horn- and waveguide-type antennas of the ATMS.The kit includes quick-lock fasteners, waveguide-to-coaxial cable adapters (SMA connector), a waveguideplastic holder, a waveguide short-circuit, and coppertape to modify the characteristics of the slotted-waveguide and patch antennas.

Model 9595 – Antenna Support

The Antenna Support is used as a mount for the fixed(transmitting) antenna of the ATMS. It comes withdifferent adapters to mount different types of antennas.

13

PERSONAL COMPUTER REQUIREMENTSA Pentium-type personal computer running under Microsoft® – Windows® XP or Windows® Vista – is required to runthe LVDAM-ANT software.

SPECIFICATIONSModel 9505 – RF Generator 120 V – 50/60 Hz 220 V – 50 Hz 240 V – 50 HzPower Requirement 1 A 0.5 A 0.5 A

Unregulated DC Output (Power Bus) +25 V typ. – 1 A max.; !25 V typ. – 1 A max.; +11 V typ. – 1 A max.

1-GHz RF Power Output Impedance 50 Ω

Power Level +3 dBm (typical); 0 dBm (minimum)

10-GHz RF Power Output Impedance 50 Ω

Power Level +10 dBm (typical)

1-GHz Tuning Voltage Input Voltage Range 0 to 10 V

Frequency Range 700 to 1200 MHz

Protection AC Line Input Circuit Breaker

Unregulated DC Power Bus Circuit Breaker

Physical Characteristics Dimensions (H x W x D) 112 x 330 x 300 mm (4.4 x 13.0 x 11.8 in)

Net Weight 6.1 kg (13.4 lb)

Models 9506 and 9506-A – Antenna Positioner Unregulated DC Power Requirement +25 V – 90 mA, !25 V – 90 mA, +11 V – 90 mA

Drive Motor Power Input 24 V – 1.25 A – AC

RF Detector Frequency Range 1 to 15 GHz

Input Impedance 50 Ω

Maximum Input Power 100 mW, CW

Signal Amplifier Input Impedance 10 k Ω

Center Frequency 1 kHz

Signal Output Voltage Range 0 to +10 V

Impedance 600 Ω

Physical Characteristics Dimensions (H x W x D) 260 x 385 x 250 mm (10.2 x 15.2 x 9.8 in)

Net Weight 10.2 kg (22.4 lb)

Model 9507 – Data Acquisition Interface / Power Supply 120 V – 50/60 Hz 220 V – 50 Hz 240 V – 50 HzPower Requirement 1.5 A 0.8 A

Data Acquisition Interface Analog Signal Input Voltage Range 0 to +2.5 V

Analog Signal Input Impedance 1 MΩ

Power Supply Unregulated DC Power Bus Output +25 V typ. – 1 A max.; !25 V typ. – 1 A max.; +11 V typ. – 1 A max.

Drive Motor Power Output 24 V – 1.5 A – AC

Physical Characteristics Dimensions (H x W x D) 167 x 330 x 300 mm (6.6 x 13.0 x 11.8 in)

Net Weight 8.5 kg (18.8 lb)

Model 9556 – Multi-Beam Array AntennaFrequency Range 8.0 to 12.4 GHz

Overall Array Gain (@ 10.5 GHz) 10 to 13 dB

Maximum Sidelobe Level !15 dB

Maximum VSWR 1.8

Polarization Horizontal

Scanning Range ±35E

Number of Beams 8

Beamwidth 6E ±1E

ANTENNA TRAINING AND MEASURING SYSTEMMODEL 8092

14

SPECIFICATIONS (cont'd)

Model 9556 – Multi-Beam Array Antenna (cont'd)Physical Characteristics Dimensions (H x W x D) 70 x 380 x 430 mm (2.8 x 15.0 x 16.9 in)

Net Weight 1.0 kg (2.2 lb)

Model 9562 – Log-Periodic AntennaFrequency Range 700 to 3600 MHz

Gain (typical) 7.0 dB

Maximum VSWR 2.0

H-Plane Beamwidth 100E

E-Plane Beamwidth 60E

Input Impedance 50 ΩFront-to-Back Ratio 5 dB min., 15 dB typicalPhysical Characteristics Dimensions (H x W x D) 73 x 287 x 192 mm (2.9 x11.3 x 7.6 in)

Net Weight 0.13 kg (0.28 lb)

Model 9563 – Two Element Phasing KitOperating Frequency 1 GHz

RF Cable Lengths 30.0, 35.4, and 40.8 cm (11.8, 13.9, and 16.1 in)

Physical Characteristics Dimensions (H x W x D) 73 x 287 x 192 mm (2.9 x11.3 x 7.6 in)

Net Weight 1.58 kg (3.4 lb)

Model 9596 – Parabolic ReflectorFrequency Range 8.0 to 12.4 GHz

Gain (typical) 27 dB

H-Plane Beamwidth (@ 9.0 GHz) 6E

E-Plane Beamwidth (@ 9.0 GHz) 8E

Input Impedance 50 Ω

Physical Characteristics Dimensions (H x W x D) 375 x 370 x 510 mm (14.8 x 14.6 x 20.1 in)

Net Weight 1.5 kg (3.3 lb)

1-GHz AntennasGain (typical) Dipole (λ/2) 1.9 dB

Folded Dipole with Balun 2.1 dB

Monopole (over ground plane) 2.5 dB

Drooping Monopole 1.6 dB

Circular Loop 2.9 dB

Square Loop 2.9 dBLozenge Loop 2.9 dB

10-GHz AntennasGain (typical) Horn (small aperture) 13.8 dB

Horn (large aperture) 16.7 dB

Helical (RHCP) 13.6 dB

Helical (LHCP) 13.6 dB

Patch (rectangular) 7.7 dB

Patch (series-fed array) 13.0 dB

Patch (parallel-fed array) 14.0 dB

Slotted Waveguide 13.2 dB

4 TBE = To be established.

15

ORDERING NUMBERS120 V – 60 Hz 220 V – 50 Hz 240 V – 50 Hz

ENGLISH FRENCH SPANISH ENGLISH FRENCH SPANISH ENGLISH8092-00 8092-01 8092-02 8092-05 8092-06 8092-07 8092-0A9505-00 9505-01 9505-02 9505-05 9505-06 9505-07 9505-0A9506-00 9506-01 9506-02 9506-00 9506-01 9506-02 9506-009506-A0 9506-A1 9506-A2 9506-A0 9506-A1 9506-A2 9506-A09507-30 9507-31 9507-32 9507-35 9507-36 9507-37 9507-3A9529-00 9529-00 9529-00 9529-00 9529-00 9529-00 9529-009535-A0 9535-A0 9535-A0 9535-A0 9535-A0 9535-A0 9535-A09550-00 9550-00 9550-00 9550-00 9550-00 9550-00 9550-009551-00 9551-00 9551-00 9551-00 9551-00 9551-00 9551-009552-00 9552-00 9552-00 9552-00 9552-00 9552-00 9552-009553-00 9553-00 9553-00 9553-00 9553-00 9553-00 9553-009554-00 9554-00 9554-00 9554-00 9554-00 9554-00 9554-009555-00 9555-00 9555-00 9555-00 9555-00 9555-00 9555-009556-00 9556-01 9556-02 9556-00 9556-01 9556-02 9556-009560-00 9560-00 9560-00 9560-00 9560-00 9560-00 9560-009561-00 9561-00 9561-00 9561-00 9561-00 9561-00 9561-009562-00 9562-00 9562-00 9562-00 9562-00 9562-00 9562-009563-00 9563-00 9563-00 9563-00 9563-00 9563-00 9563-009594-10 9594-10 9594-10 9594-10 9594-10 9594-10 9594-109594-A0 9594-A0 9594-A0 9594-A0 9594-A0 9594-A0 9594-A09594-B0 9594-B0 9594-B0 9594-B0 9594-B0 9594-B0 9594-B09595-00 9595-00 9595-00 9595-00 9595-00 9595-00 9595-009596-00 9596-00 9596-00 9596-00 9596-00 9596-00 9596-009598-00 9598-00 9598-00 9598-00 9598-00 9598-00 9598-00

30857-00 30857-01 30857-02 30857-00 30857-01 30857-02 30857-0030857-10 30857-11 30857-12 30857-10 30857-11 30857-12 30857-1030857-E0 30857-E1 30857-E2 30857-E0 30857-E1 30857-E2 30857-E033458-00 TBE4 TBE 33458-00 TBE TBE 33458-0035166-E0 TBE TBE 35166-E0 TBE TBE 35166-E039378-00 39378-00 39378-00 39378-00 39378-00 39378-00 39378-00

Reflecting Lab-Volt's commitment to high quality standards in product, design, development, production, installation, and service, our manufacturing and distributionfacility has received the ISO 9001 certification.

Lab-Volt reserves the right to make product improvements at any time and without notice and is not responsible for typographical errors. Lab-Volt recognizes all productnames used herein as trademarks or registered trademarks of their respective holders. © Lab-Volt 2010. All rights reserved.

94045-00 Rev. E3