Ansa v15 1 0 release notes
-
Upload
hankookaac -
Category
Documents
-
view
278 -
download
2
description
Transcript of Ansa v15 1 0 release notes
ANSA v15.1.0 Release Notes Introduction
BETA CAE Systems S.A.
v.15.1.0v13.1.1
ANSA v15.1.0 Release Notes Introduction
BETA CAE Systems S.A.
Kato Scholari, Thessaloniki
GR-575 00 EpanomiGreece
Tel. : +30-2392021420, 30-2311993300Fax. : +30-2392021417
http://www.beta-cae.gr
Queries & Services : [email protected]
BETA CAE Systems S.A.
ANSA v15.1.0 Release Notes Introduction
1. Introduction
This document contains all the information about problems fixed during development of ANSA from version 15.0.2 to version 15.1.0.
NOTES:
•ANSA databases saved by ANSA v15.1.0 can be opened by v15.x.x but not with v14.x.x or previous versions.
•New/Updated documents:
➢ NASTRAN tutorial: NASTRAN Embedded Fatigue Model Set-up
➢ CFD OPTIMIZATION: ANSA-FLUENT-META
➢ BATCH SOLID MESH: MESHING AND ASSEMBLY
➢ TOOLS: Results Based Mesh Refinement
Release History:
v15.1.0 2014.05.08
v15.0.2 2014.04.28
v15.0.1 2014.02.24
v15.0.0 2013.12.30
v14.2.3 2013.12.20
v14.2.2 2013.09.15
v14.2.1 2013.10.02
v14.2.0 2013.08.01
v14.1.3 2013.08.29
v14.1.2 2013.06.26
v14.1.1 2013.05.13
v14.1.0 2013.04.08
Copyright notes: All other company and product names mentioned in the software and its documentation are property, trademarks or registered trademarks of their respective owners.
BETA CAE Systems S.A.
ANSA v15.1.0 Release Notes What's New
2. What’s new in v15.1.0Enhancements – New Options – New Features
GENERAL
Touch Screen
The touch screen application is now introduced. This makes ANSA suitable for presentations and for use on devices without the need of keyboard. This is available for Windows OS only and when touch screen is provided.
• The actions to control the model view:
➢ Zoom in/out
➢ Rotation by (i) a point, (ii) an axis
➢ Panning
• Picking, Confirming and Opening of context menus:
➢ Selecting/Picking (like left mouse button) – One finger tap
➢ Confirming/proceeding (like middle mouse button) – Two fingers tap
➢ Opening of context menus (like right mouse button) – One finger in prolonged tap
BETA CAE Systems S.A. 4
ANSA v15.1.0 Release Notes What's New
Touch Screen
• Selections from model/lists and virtual keyboard
➢ The Touch Assistant controls the selection/deselection operation switch and the virtual keyboard activation. It can be activated through the right-click menu on the toolbar area.
➢ For selections (box type/ lists) it is required one finger tap and dragging.
32-bit Platform
Discontinuation support for Linux OS.
Display Styles
New tool is now introduced that stores the current visibility buttons status under a given name.
The tool stores:
• All buttons that control the visibility of a feature e.g. Wire, Geometry, Shadow, etc.
• The options from the Presentation Parameters tab of the F11 card.
[Incident: 48083]
Taskbar window
Now, any ANSA session that is minimized, the name of the opened database is displayed instead of the full path name.
[Incident: 43400]
File Open/Save now support progress bar.
[Incident: 49573]
BETA CAE Systems S.A. 5
ANSA v15.1.0 Release Notes What's New
Windows Settings
The stored paths in the .xml file (open/input recent) can now be cleared by pressing the respective button.
[Incident: 44132]
Settings>General settings
When a session unexpectedly terminates, it is now possible to:
• Save the database (Crash report path)
• Re-open the database (Recover Database path)
To decrease the possibility of loosing the current database when terminating, it is recommended to have the option “Recover Database path” always active.
Settings>Buttons Manager
Now, the standard views (Fi and Ctrl+Fi) can be controlled with user-defined short-cut buttons.
[Incident: 48300]
Settings>Resolution
The Curves resolution can now be as low as the Perimeters Length.
[Incident: 41961]
Settings>GUI Settings>General
The Rotation Center can now be visible. Its color and radius can be edited.
BETA CAE Systems S.A. 6
ANSA v15.1.0 Release Notes What's New
GUI Special toolbar for the model View and Rotation actions is now supported. Making right-click on any toolbar, the option “Views” can be activated that makes visible this toolbar.
It mainly supports the “F” view buttons and a new one called “Zoom Area”. These will aid the use of devices with no keyboard.
[Incident: 34766]
Zoom by a window is now supported under the “Rectangle Zoom” option. The area included in the selection-box will be fitted to the screen.
[Incident: 43103]
Zoom in/out Now, zooming with the mouse wheel is possible even when the Ctrl button is pressed.
[Incident: 47632]
BETA CAE Systems S.A. 7
ANSA v15.1.0 Release Notes What's New
Focus Select Front Only
Focus functions can now select the front entities (faces, shells and solids) which actually are only drawn according to the current view.
This is a special selection assistant button and applies when selecting with box or polygon selection method.
[Incident: 15531, 44494]
Near
The “Dense search” option is now supported in order to give more accurate results from big entities, e.g. from faces.
[Incident: 43380]
LOCK
The button activation/deactivation can now be controlled through a custom short-cut.
[Incident: 49278]
Menubar Utilities>Best
It can now be applied on solid elements facets too.
[Incident: 47646]
Lists A tooltip is now provided for the listed items in order to display the whole field when this is not possible due to narrow column width. E.g. the name of a property.
[Incident: 47040]
BETA CAE Systems S.A. 8
ANSA v15.1.0 Release Notes What's New
CAD Import / Export
Import JT files can now be imported (translated) directly in ANSA.
IGES reading has been improved for specific cases.
[Incident: 48741]
CATIA
• Now, the Annotations are read and they are written to the Comment field of the entity that they refer to.
• User-defined parameters assigned on entities which exist under a geometric set can now be read.
[Incident: 38402, 32434, 48997]
CAD Translators
The size/position of the Translators output window and the File manager window are now saved the file named as TranslGUIOptions.dat, when the button “Save Options” is pressed.
[Incident: 44492]
The NX (UGOpen) menu now points to the ansa_ug9.sh run file. Also, the field “Script to run” is now saved when the button Save Options is pressed.
[Incident: 48952]
COMPARE
Compare>Build variants
New tool is now supported which creates one new model with the variants of the original models as different configurations in the Parts Manager. For example, a car with first variant the normal roof and second variant the sun roof. When compared, different configurations are created for each variation.
BETA CAE Systems S.A. 9
ANSA v15.1.0 Release Notes What's New
The option Tools>Create New Model in the Compare Report window is now supported. It provides a wizard to simply create the new model from the compared ones, by traveling through all the parts.
[Incident: 48570]
The function Tools>Model Updates has been enhanced with new options. Each part can be classified as “Minor difference” or “Major difference” and the respective options are then given.
Now, the Compare filter settings are saved along with the ansa_compare file.
[Incident: 45125]
Model differences between the solid description and the middle description can now be identified.
The shell element thickness differences can now be identified. This is applicable only for FE models comparison.
Data Management
Generic Entity Builder (GEB): When Multi-Instantiated parts are selected as “connectivity”, a warning window pops-up where the user can continue or include all Instances.
[Incident: 48198]
The option to whether save or not the internal connections/connectors/GEBs is now provided in the Windows>Settings.
[Incident: 42633]
BETA CAE Systems S.A. 10
ANSA v15.1.0 Release Notes What's New
Connections & Assembly
View Modes New view modes make possible to overview the model according to the attributed Names and Comments.
[Incident: 46465]
Connection Manager The Inspect tool is now available in order to control interactively every connection entity and its connectivities.
The tool opens as a separate window which can be docked and then by choosing from the list or by using the short-cuts inspect one-by-one the selected connections according to options provided.
• The N & P buttons move to the next/previous listed connection
• The 1 to 5 button numbers activate/deactivate the corresponding options.
BETA CAE Systems S.A. 11
ANSA v15.1.0 Release Notes What's New
Connection Manager The available options are:
• Show Connectivity – Shows/Hides the parts that are connected on this connection
• Show all with – Shows the rest of the connections that are connected with the visible parts
• Zoom – For every new selected connection from the list, zooms on the part
• Fe Rep – Shows/Hides the FE representation
[Incident: 45659]
New Apply button is now provided. When the settings of FE Representation are changed, they can be applied on the selected connection entities by pressing this button.
[Incident: 44378]
Connection entities now are not Erased/Realized if they have status FROZEN_DELETE=YES. A warning message pops-up to confirm.
[Incident: 48767]
Connection Entities Robscan
New entity is now available to support the FEMSITE-ROBSCAN representation.
[Incident: 45795]
BOLTs New option Use Bolt Geometry (yes/no) is now available to align the body either (i) perpendicularly or (ii) according to the bolt's direction.
[Incident: 35796, 48295]
BETA CAE Systems S.A. 12
ANSA v15.1.0 Release Notes What's New
Convert FE to Seamline
The RBE3-CONNECTOR-RBE3 representation can now be converted.
[Incident: 48359]
Connection to Connection
While the function is active the rest of the model turns to transparent view mode.
[Incident: 48852]
User Attributes They are now also accessible through the Connection Manager, in the right-click list of options.
[Incident: 46497]
CHECKs Flanges Weld Spots
Flanges with no connections are now reported separately.
[Incident: 47273]
Template Support of the option to apply scripts on the Fe-representation of a template, using the field “Post Realize Function”.
[Incident: 43131, 44666]
FE Representations
SOLID BOLT New option is now supported to dis-associate the mesh of the Head from the Body.
[Incident: 33248]
BOLT_ON_SOLID The option to attach on “Bottom Ring” is now also provided.
[Incident: 49584]
BEAM_BOLT • Now, the Shank diameter can be defined
• The rings can now be skipped with the option “skip tube rings” in the Interface section
• A new Shank scheme “BEAM BOLT” is now available that combines Beam and Solid elements.
[Incident: 49457, 50004]
SPIDER2 The option to define the number of affected zones is now supported under the name “Num of shell zones affected”. If left blank, a default value is considered.
[Incident: 46746]
BETA CAE Systems S.A. 13
ANSA v15.1.0 Release Notes What's New
SOLID NUGGED The Scheme CONTACT supports new field “Orient Solids by” in the Body section of the settings. Two options are available:
• Fusion Zone – Follows the orientation of the hole
• Flange – Follows the flow of the flange
[Incident: 48931]
RBE3-SHELL-RBE3 New option “Weld Shell Thickness Factor” is now provided.
[Incident: 48799]
RBE3-CONNECTOR-RBE3
The coordinate system is now defined on node.
[Incident: 49336]
FEMSITE-SPOTWELD
The button “Directories” is now provided at the bottom area of the FE REP settings section, which opens directly to the Windows>Settings>Connections>Femsite-Spotweld.
[Incident: 46145]
BETA CAE Systems S.A. 14
ANSA v15.1.0 Release Notes What's New
TOPO
CONS Project
Support of the option to create curves at the intersection with the faces, instead of cutting them.
Project
The option “Paste” is now provided. If the distance between the source entities (cons, curves) and the target faces smaller than the “Cons Matching Distance” (Tolerances); they will be pasted.
Release>Volumes
New function to disconnect geometrical volumes that have been topologically pasted.
• The function works on visible faces
• Even one selected face is enough for the function to identify the volumes and disconnect them
[Incident: 48340]
BETA CAE Systems S.A. 15
ANSA v15.1.0 Release Notes What's New
CONS Open Hole
• The direction of the hole can now be modified, by moving/rotating the coordinate system
• New option “Produce Cylinder” creates the cylinder between two or more selected faces that the hole axis intersects with.
Faces Mid. Surface>Calculate Thickness
The thickness can now be assigned either on nodes or on properties, according to the inserted step value.
[Incident: 47888]
Casting
Now the information of material and property names & attributes are transferred from the original volume parts to the new middle extracted parts.
BETA CAE Systems S.A. 16
ANSA v15.1.0 Release Notes What's New
Faces Flanges>Simplify
New function that simplifies the flanges shape.
• The desired red conses have to be selected by simple pick or by area selection method
• These cut-patterns are discriminated from the main flange by hot points at the start and end points
• Multiple cut-patterns can be selected in one step
Alternatively, the function converts the rounded areas to sharp edges. The only requirement is that the area has to be marked by hot points at the start/end points.
[Incident: 27099]
Fuse>Project
New option that projects and connects every visible single (red) CONS to the visible neighboring faces. The maximum searching distance is taken from the current value of Nodes matching distance (Windows>Settings).
[Incident: 48001]
Plane Cut
Now, progress bar is supported.
[Incident: 24999]
BETA CAE Systems S.A. 17
ANSA v15.1.0 Release Notes What's New
Surfaces Fillet>Surfaces
The former Fillet function is now relocated as sub-option.
Fillet>Faces
New function is now introduced that creates continues fillets from multiple faces.
• Selection of yellow CONs is required
• The orientation of faces does not affect the result
• The created fillet has constant radius
Points On COG>Points & Relative
Selection assistant tools (e.g. Feature Line) are now supported.
[Incident: 42814, 31990]
Relative
The value fields now follow the resizing of the window, so that long values can be visible.
[Incident: 35620]
Scripting Support of the functions: CrossSectionsMulticut & ZoneCut
[Incident: 41163, 30332]
SHELL MESH
Perimeters Number & Num+/-
The displayed numbers on every perimeter now refer to the counted edges instead of nodes.
[Incident: 48298]
BETA CAE Systems S.A. 18
ANSA v15.1.0 Release Notes What's New
Perimeters Spacing>Auto CFD
• Trailing edge refinement now contains user control angle
• Interior type faces are now checked for both sides proximity
• The mesh growth between size boxes and near perimeters is now smooth
• It is now possible to select the perimeters/macros to apply
[Incident: 33132, 40054, 40077, 50099]
Shell Mesh Reconstruct / Reshape / Batch / Split
New option “Freeze>Line elements” in Mesh Parameters is now provided. Elements (e.g. RBE2) sharing nodes with shell elements follow the resulting mesh, if the option is not active.
[Incident: 624, 1101, 46997, 21985]
Project
When the source curves/edges/perimeters describe a closed loop, the new option “Open closed perimeter hole” can be used to delete the included by the projection elements.
[Incident: 49776]
Fix Quality
The 2nd nodes can now be constrained. They respect the option “Maximum distance from perimeter” of the Mesh Parameters.
[Incident: 36659]
Volumize>Composites
New option is now supported that converts the shell to solid laminates, creating also a new SOLID_LAMINATE property.
BETA CAE Systems S.A. 19
ANSA v15.1.0 Release Notes What's New
Checks Sharp Edges
An automatic “Fix” option is now provided for the detected errors.
[Incident: 49150]
Scripting The function MultiNumber supports the nodal renumbering of multiple perimeters.
[Incident: 48345]
VOLUME MESH
Structured Mesh
Layers
The Y+ calculator is now supported.
[Incident: 35511]
Scripting Support of the VoxelGeneration function in both python and Beta scripting language.
[Incident: 48005]
Batch Meshing
Scenario It is now possible to load script functions on every scenario. Two separate scripts can be loaded to be run, one at the start and another one at the end of every scenario.
The scripts are loaded through the right-click menu of the scenario, at the “Script” option.
[Incident: 14883, 21446]
Scripting Support of Layers and Wrap creation, using the functions:
GetNewLayersArea & GetNewWrapArea.
[Incident: 25256]
DECKs
Input The location where all the “log” files are stored (e.g. ANSA_Input.log) can now be defined in Windows>Settings>General Settings.
[Incident: 7014, 32904]
BETA CAE Systems S.A. 20
ANSA v15.1.0 Release Notes What's New
Output When variable element thickness is detected and the option to export this information is not active, a warning message is displayed.
[Incident: 44180, 12054, 10799]
General Connectors / GEBs
When Multi-Instantiated parts are selected for the Connectivity field, a warning window prompts whether to keep only the selected part or all the multi-instances.
In addition, the Module Id of the Multi-Instantiated part is also displayed.
[Incident: 44235]
General Mat Sync
The NASTRAN fields “A” and “TREF” of *MAT1 are now transferred to Abaqus *BEAM_SECTION fields “ZERO” and “ALPHA”.
[Incident: 48208]
ELEMENTs UTIL>Remesh 1D elements
Now, two target options are provided: (i) the number of elements and (ii) the element length.
[Incident: 43390]
UTIL>Mass Balance
The warning messages are now more informative.
[Incident: 48821]
The creation of line elements like RBE3 & COUPLING is now possible using the node sets.
[Incident: 48907]
AUXILIARIES CONTACT>Flanges
New option “Include connection elements” considers also solid bolt created by the Connection Manager.
[Incident: 49903]
Checks Checks Manager
Selecting a check from the drop-down menu it is now executed immediately if there are no parameters to define.
[Incident: 46572]
Penetrations>Intersections & Interior Intersections
The support of Multi-thread run has significantly reduced the processing time.
[Incident: 47956, 48120]
Trias Attached On Boundary
The number of detected elements is now also reported.
[Incident: 48296]
Sharp Edges
Fix option is now supported, affecting the defined number of zones.
[Incident: 49150]
Flanges Weld Spots
The option “Maximum weld spot distance” is now also available.
[Incident: 47264]
BETA CAE Systems S.A. 21
ANSA v15.1.0 Release Notes What's New
D.Info New option Part Image is now supported in the Model tab. It adds a small image next of each part at the mass information section.
[Incident: 37487]
Now, most of the quality criteria are now available for Shell and Solid tabs.
[Incident: 31918]
It is now possible to add/remove ranges for every criterion, using the +/- buttons. Additionally, the number of Classes can be up to 100.
[Incident: 48656]
New option Synchronize updates the Classes (ranges) of the criteria with the values from the F11 card. In case that only the “Failed” value is used (not ranges), the synchronization will transfer this value in the middle Class of D.Info.
[Incident: 12926]
Now a Part with representation “Don't Use” is not taken into account for mass calculation when the Whole database is considered.
[Incident: 42845]
GEBs The MappedArea search type now supports also the option to project on direction, taking as vector the dx, dy & dz fields.
[Incident: 48845]
GEB MT
The “Representation” area now has also the option “result by node”, which distributes the mass on the elements' node.
[Incident: 48920]
SETs The option “Modify contents” is now provided in the bottom buttons when some entities are selected.
[Incident: 46258]
Results Mapper
The Nodal thickness mapping now supports also the COMMON AREA Interpolation method. This converts the incoming nodal thickness to average element thickness and as a result all the nodes of each element have the same thickness values.
[Incident: 47986]
New field “user_script_apply_args” is now provided in order to add user arguments, e.g. To apply specific STEP.
[Incident: 44374]
The offset of Layup files is now read.
[Incident: 43954]
BETA CAE Systems S.A. 22
ANSA v15.1.0 Release Notes What's New
Laminates New option “Apply Thickness to elements” is supported in the right-click menu. It applies the defined thickness of the Layers so that the actual element thickness is equal to the layers' total thickness.
Now, multiple copy of the selected Layers can be created by using the option Copy>Multiple Copy in the right-click menu.
[Incident: 24581]
Laminates The Mapped Data window now supports also the options to (i) Filter the listed items and to (ii) Modify.
[Incident: 28534]
Results Mapper
PAMSTAMP LAM now supports the option “Split woven fabric to two UD”.
[Incident: 48783]
Materials Database
Now, reading directories can be assisted by a filter manager, when choosing the new option “Filtered Files From Directory”.
[Incident: 25084]
Materials The Shear Modulus “G” is now transferred from NASTRAN to Abaqus when applying Material Synchronization.
[Incident: 47650]
Properties The fields of BEAM properties that are related to Cross Sections now cannot be edited and a message informs the user.
[Incident: 31642]
Scripting New python script function DeckMassInfo() returns an object with the total mass, the center of gravity and the inertia tensors of the model.
[Incident: 46097]
BETA CAE Systems S.A. 23
ANSA v15.1.0 Release Notes What's New
Safety
Pedestrian • The flag “Transparency” is now provided in the Target Points section.
• The option “Boundaries only” is now provided for creation of the boundary Reference lines only. The option is located in the Advanced options of Car Marking tab.
• Insert a Target point on the BLE curves by inserting a value corresponding to the y-axis.
[Incident: 47209, 47440, 47439]
The curves created for the WAD lines representation are now added in different SETs according to the protocol.
[Incident: 46214]
Seatbelt The Belt Tension tool now works also for hybrid components.
[Incident: 49311]
Scripting Support of the python function PedestrianCreateWADLine.
[Incident: 47452]
Tools
Results Based Refinement
A new tool is now available in ANSA as a script. Its purpose is to set up and drive a process within ANSA for refining the mesh in areas of high interest based on results output by the solver.
During this process ANSA drives the solver (NASTRAN or Abaqus) and μΕΤΑ in a loop. If ANSA starts with the Durability layout, the tool is automatically loaded and available in Windows > User Script Buttons > Tools > Auto Refine. Alternatively, the button can be loaded from Tools > Script > Load by reading the main.pyb file from the scripts/ResultsBasedRefinement/ folder in ANSA installation directory. Documentation is also available.
The script is located in the installation directory of ANSA at: .../scripts/Auxiliaries/ResultsBasedRefinement)
BETA CAE Systems S.A. 24
ANSA v15.1.0 Release Notes What's New
NASTRAN
B.C.SETs HEADER
Support of the CUBIC calculation method for stress plotting.
[Incident: 47415]
The TF SET is now supported.
[Incident: 17684]
BCs PANELS now support also the option ERPPNL.
[Incident: 32738]
The ACCEL1 option is now supported.
[Incident: 46352]
The TF is now supported
[Incident: 17684]
AUXILIARIES FATIGUE
The FTGDEF, FTGPARM and FTGSEQ now support FTGSET field (SID).
Checks Fluid Nodes
Detects the nodes which do not have CD=-1. A fix option is available on the right-click.
[Incident: 26746]
Properties PBUSH now supports also the field “M” for the lumped mass.
[Incident: 41278]
Material Support of the poroelastic material MATPE1.
[Incident: 47319]
Abaqus
Output Now, the *HEADING keywords can be exported by activating the corresponding option in the Miscellaneous tab of the Output Parameters window.
[Incident: 40432]
General Support 9-digit ids for coordinate systems, connector sections and sets.
[Incident: 49140]
Elements RIGID_BODY
The card does not close when OK is pressed if either of the defined Analytical surfaces or the sets are empty.
[Incident: 45724]
BETA CAE Systems S.A. 25
ANSA v15.1.0 Release Notes What's New
Elements MASS
Support of the ALPHA parameter for both *MASS and *ROTARY inertia.
[Incident: 49062]
SPRING
Now, the option to define the number of DOFs is supported, avoiding to repeat the function as many times as the number of DOFs.
[Incident: 48361]
INIT CONDITIONS
INIT CONDITIONS>TEMPERATURE>File
The options INC and STEP are now supported.
[Incident: 48580]
AUXILIARIES Support of the *PSD-DEFINITION and *CORRELATION keywords for random response analysis.
[Incident: 44166]
STEP
The *ELEMENT_OUTPUT now supports also the option EXTERIOR.
[Incident: 49022]
Laminates
The option “Output PCOMPS=Clustered” is now supported in the *LAMINATE property.
[Incident: 49488]
LS-DYNA
Input / Output A warning pops-up when variable nodal thickness exits but the option to output is not active.
[Incident: 44180]
The Long Format is now supported.
[Incident: 30854]
The labels of the *DEFINE_TRANSFORMATION can now be exported as comments.
[Incident: 48505]
BETA CAE Systems S.A. 26
ANSA v15.1.0 Release Notes What's New
CONTROL Support of the keywords:
*CONTROL_IMPLICIT_MODAL_DYNAMIC*CONTROL_IMPLICIT_MODAL_DYNAMIC_DAMPING
[Incident: 47911]
DATABASE Support of the *DATABASE_FREQUENCY_BINARY options.
[Incident: 47906]
DEFINE_COORD Support of the keyword *DEFINE_VECTOR_NODES.
[Incident: 47639]
ELEMENT ELEMENT_SHELL now supports the option “SBRID”.
CONSTRAINED CONSTRAINED_RIGID_BODIES now support different coloring for master/slave.
[Incident: 46883]
INITIAL VELOCITY>Generation
Support of the option IVATN.
[Incident: 49611]
AUXILIARIES DATABASE_CROSS_SECTION_PLANE
• The created GEB_OR acquires now the same id with the CROSS_SECTION, provided that this is available.
• Now, the plane can be moved using the synonymous option on the right-click menu. In addition, a middle point on the plane is provided for easier picking.
[Incident: 45571, 44008]
SENSOR
Support of the options *SENSOR_DEFINE_FORCE and *SENSOR_DEFINE_NODE.
[Incident: 37269]
Support of the *DEFINE_BOX_LOCAL.
[Incident: 47686]
RIGIDWALL
The option _DISPLAY is now supported.
[Incident: 48346]
*DEFINE_CURVE now accepts *PARAMETERs for the Y values. This is possible through the Database Browser.
[Incident: 47745]
The *RIGIDWALL_FORCE_TRANSDUCER is now supported.
[Incident: 46917]
BETA CAE Systems S.A. 27
ANSA v15.1.0 Release Notes What's New
ChecksMesh>Isolated Solids is now supported.
[Incident: 50147]
Materials The option MAT_ADD_EROSION is now supported for all the rest of the materials.
[Incident: 45550]
PAM-CRASH
Input Support of the Multistage import by creating new Includes for the incoming Stages.
[Incident: 21079]
CONSTRAINTs MTOCO
Support of the sensor option under the name ISENS.
[Incident: 47527]
CONSTRAINTs MTOCO>Branch
The free nodes are now highlighted in different color.
[Incident: 41618]
LINCO entity is now supported.
[Incident: 15284]
AUXILIARIES GEB_BC
Support of the option TYPE=PSMESH for Pretension representation.
[Incident: 46836]
BETA CAE Systems S.A. 28
ANSA v15.1.0 Release Notes What's New
ANSYS
LOADs BF
Support contour plotting for the chosen Load Step.
The *SLOAD pretension load is now supported.
[Incident: 30744]
AUXILIARIES PRTENS
The PSMESH type is now also supported through the Assistant.
[Incident: 47767]
PEM
The keywords TRMCPL and ACPEMCP are now supported.
CONTROL
Support more options of the OUTRES type.
Includes They are now supported for input / output.
Properties PSOLID
The option PORO is now supported for the FCTN option.
PBEAM now supports text for the KEYOPT(7) and KEYOPT(8).
[Incident: 48923]
Materials Support of Failure Criteria under the FC button.
[Incident: 45528]
The FRIC field is now supported in the material's card.
[Incident: 26960]
The BISO filed is now supported.
[Incident: 49182]
BETA CAE Systems S.A. 29
ANSA v15.1.0 Release Notes What's New
RADIOSS
AUXILIARIES BOX
Support of the Types Cylinder and Sphere.
[Incident: 31880]
Properties The option ISH3N is now supported for PROP/SHELL and in CONTROL>DEF SHELL.
[Incident: 47661]
SESTRA
Support of the visualization of the Loads intensity, using the EL.PRESS view mode.
[Incident: 40341]
Support of the MODEL CUT function in Auxiliaries group. The creation of Cutting Planes can be optionally followed by the creation of BNBCDs on their bounds.
[Incident: 41451]
CONTROLs section now support the LOCS option.
[Incident: 49591]
The script function ResultantForce is now supported.
[Incident: 45969]
BETA CAE Systems S.A. 30
ANSA v15.1.0 Release Notes What's New
RADTHERM
The elements thickness view mode is now supported.
[Incident: 48914]
KINETICS
Graphics Support of basic shapes types for Road, Tire and Extrude. Regarding road graphics, several 2D types are provided. In addition, it is possible to import a road file of type .rdf, .crg or .rgr.
[Incident: 46357]
Bodies The Tire body type is now supported. Upon creation of a body, the graphic shape is automatically created.
In addition the Pacejka MF (pac2002) steady-state and FTire models (cosimulation) are supported.
Joints Point to Surface joint is now supported. It is possible to constraint a point of a body (lift-off is not allowed) to move along a surface.
Contacts The contact definitions are now improved. The Friction parameters and definitions that are now supported are:
• Friction types: PLANAR (1D) and SPATIAL_ISOTROPIC (2D)• Stribeck effect• Drilling friction
Auxiliaries Tracer
New tool to calculate the trailing path of specific points with respect to other moving bodies, after a simulation has run.
Simulation Results Viewer
Calculations for plotted curves are now supported. The following calculations have been implemented: Add, Subtract, Multiply, Interpolate, Scale, Offset, Differentiate, Integrate and FFT.
BETA CAE Systems S.A. 31
ANSA v15.1.0 Release Notes What's New
CROSS SECTION
Resolution In Windows>Settings it is now provided the field Cross curves resolution. It affects the drawing of Bar/Beam cross sections.
[Incident: 45737]
Scripting Support of the functions: CrossSectionsAdd, CrossSectionsCut and CrossSectionsMulticut, CrossSectionsNew.
[Incident: 35479]
The function ExtractCrossSectionsFromPlane
to convert Cutting Planes to Cross Sections is now supported.
[Incident: 47099]
MORPH
Controls Nested
New option “create multi” creates separated nested elements for all the selected areas.
[Incident: 48214]
Hatches Paste
See Hexa Block>Boxes section.
[Incident: 48664]
Direct Morphing
DFM
The options Offset and Transform are now also provided.
BETA CAE Systems S.A. 32
ANSA v15.1.0 Release Notes What's New
Direct Morphing
Slide>Feature
The option to copy the feature multiple times is now possible, using the “Steps” counter.
Stamping
New tool is now introduced to quickly and easily create on FE parts: (i) Opening, (ii) Flanged opening, (iii) Bead and (iv) Stamp.
For each of the above shapes, various parameters can be chosen, regarding their type, e.g:
BETA CAE Systems S.A. 33
ANSA v15.1.0 Release Notes What's New
HEXA BLOCK
Boxes Paste
New option “Paste on middle” moves the box faces on the middle distance before pasting them.
[Incident: 48664]
Coarse
New function to create transition zones of multiple box splits in order to avoid high variation on element size.
The steps to create are:
1. Select the affected boxes
2. Define the direction of coarsening
3. Set the desired Ratio either 2:1 or 3:1 and distance from starting points of the selected boxes
Shell/Volume Mesh
Map / Pure Hexa
The option to enable/disable “Smooth” is now supported.
[Incident: 49763]
BETA CAE Systems S.A. 34
ANSA v15.1.0 Release Notes What's New
Scripting
An .html based help for the Python API is now supported under the Help>ANSA Documentation Index.
Script Editor: Closing a tab now provides also the option to cancel aborting.
[Incident: 48264]
The PrintToFile function now works also in nogui mode.
[Incident: 18060]
SCRIPT COLLECTION
AnsaToVirfac (.../scripts/Auxiliaries/)
Exports three text files that associate the ANSA model to Virfac.
BETA CAE Systems S.A. 35
ANSA v15.1.0 Release Notes Known problems resolved
3. Known Problems resolved in v15.1.0
CAD Import / Export
Import The information of Geometric Set was not stored in the Comment field of the corresponding FACE edit card when the option “Read geometric sets/publications” in Settings>Translators options was active.
[Incident: 47752]
Connections & Assembly
Seamwelds RBE3-CONNECTOR-RBE3
It would not attach to the detected single edges of both sides.
[Incident: 46422]
Bolts BEAM BOLT FE Representation would not display any warning message in case of penetration between the shank Beam and the hole Beams.
[Incident: 49457]
SHELL MESH
Perimeters Spacing>Auto CFD
• Very accurate proximity refinement led to high mesh variation
• Applied on Linked faces would lead to unexpected termination
• Enhanced proximity refinement would lead to over-refinements
[Incident: 46011, 49272, 49900]
Macros Cut
The “Remesh” option would mesh neighboring unmeshed macros.
[Incident: 50023]
Elements Split Quads
The nodes would move to their original position on the geometry.
[Incident: 49267, 48866]
BETA CAE Systems S.A. 36
ANSA v15.1.0 Release Notes Known problems resolved
VOLUME MESH
Define Auto Detect
The process would significantly delay.
[Incident: 49354]
Unstructured Mesh Tetra Rapid
The length of the size boxes would occasionally not be respected.
[Incident: 48712]
BATCH Meshing
Features Chamfer
Occasionally features could not be identified but they were treated correctly though.
[Incident: 48468]
Holes
It would give bad results at circular-shaped beams because of not precise holes recognition.
[Incident: 48780]
DECKs
Input / Output VRML files could import / export wrong model geometry, because of wrong units conversions.
[Incident: 17541, 49481, 20751]
Importing a *PARAMETER which had reference with the minus “-” sign, this would probably be not created correctly.
[Incident: 47825]
Includes Applying the Subcontainer rules would not add the nodes used by GEB_GN.
[Incident: 45159]
Materials Compress
The duplicate materials with the lower ids would be deleted.
[Incident: 49266]
In some cases, Laminates were erroneously merged and Material information was altered after mapping.
[Incident: 46111]
BETA CAE Systems S.A. 37
ANSA v15.1.0 Release Notes Known problems resolved
LS-DYNA
Input When the line before the *DATABASE_CROSS_SECTION_PLANE was comment, it would be read as the keyword's heading.
[Incident: 45856]
Output Exporting the *Parameter keyword labels through the “Output Parameters>Filter” , the corresponding comments were not typed exactly as they should.
[Incident: 48500]
The field labels of the *DEFINE_TRANSFORMATION were not correct.
[Incident: 48505]
Abaqus
AUXILIARIES DATA TABLE
Pasting (Replace) the values of a column, they would be placed on rows instead.
[Incident: 49788]
BETA CAE Systems S.A. 38