and any floor coverings will vanish! made in Germany · coverings Delta knife, curved w = 80 mm /...
Transcript of and any floor coverings will vanish! made in Germany · coverings Delta knife, curved w = 80 mm /...
madein
Germany
WorkTec
Loosening of linoleum Pre-cutting floors
Removing of wood-block paving Removing multilayer parquet
Parquet removal Cut open and remove roof insulation
Removal of PVC-tiles
Peeling of 2-component coatings
Dismounting elastically glued laminate
Dismantling carpeted floor coverings
Detaching PU-elastic glued parquet
Loosening and cutting soft floor coverings Battering off ceramic floor tiles
... and any floor coverings will vanish!
VOGT Hammer - the Multistripper
Simply solution for difficult floor coverings
M 607 R.18
M 725.18
M 100.18
H 425.18 H
M 200.18
M 340.18
M 3140 U.18
M 5000.18
M 410.18 UP
M 408 UP.18
H
130
V 5
0-
.18
WorkTec
VOGT Baugeräte GmbH
Industriestrasse 39D-95466 Weidenberg
+49 (0) 92 78 / 774 33-0+49 (0) 92 78 / 774 33-11
H
130
V60
-
.18
ToolsIdeal on the floor for
Qualified for wall workings like
Removing of all glued floor coverings
etaching and cutting elastic coveringsDismounting PU-elastically gluedparquet and laminate floorsScraping foam backings, bondingmaterials, knifing fillers, levelings, paint and thick coatings
g
Synchronous d
Tearing up screed and pavementDetachin insulating boards
Removing ceramic
Loosening bitumen sheeting, rubber coatings, wall and flat roof sealings, 2-components coatings
wall tiles,
Cutting out PCB jointsRemoval of concrete uneveness
floor tiles and natural stone plates
Striking off ceramic intereor, exterior, and fine plasterRemoving sprayed asbestos
Eliminating of concrete residues
The advantages:Ideal for very thin coverings thanks to the downward mode of actionPreserve subsurfaceEasy and fatigueless operation due to low weightErgonomic upright working postureVibration damping plastic handle Low air consumption enables use of mobile 230 V compressorsLarge tool choiceFast tool change2 year warranty on equipment and tools
The Solution forPU-elastic and hybrid adhesives
Special BladeFrankenklinge
®
Wide chisel XL, curvedw = 140 mm / 5.5”bitumen, thermal insulation boards, panels, wooden boards
Further tools deliverable
Cross blade holder withcross blade (H 100 B)
Deflection device (U 120)rolling floor coverings frontwardParquet wedge (PK 90)Reduces frictional resistance of PU-elastic adhesives
Scraper holder (
F)
M 5000.18) with Special Blades -
®Frankenklinge optionalw = 120 mm / 4.7” (B 120 LF)w = 160 mm / 6.3” (B 160 LF)w = 200 mm / 7.8” (B 200 LRemoval of elastically glued laminate andparquet floors
Double cross blade holder with cross blades (H 200 B)Synchronous detaching and cutting elastic coverings
Delta knife, curvedw = 80 mm / 3.1”w = 100 mm / 3.9”Parquet, laminate, bitumen,thick floor tiles, wooden pavement, natural stone plates, plaster
Detaching and removing floor coverings such as PVC, needled felt, carpeted floors, etc., foam backings, compensation layers, epoxy resin and 2-components coatings, insulating boards, remaining bitumen, bonding materials, paint, or flat coats (filling compounds), fine plasters, thick wall papers, sprayed asbestos, concrete nosings, PCB joints
Scraper holder (M 5000.18)with blades, optionalw = 100 mm / 3.9” (B 100 S)w = 120 mm / 4.7” (B 120 S)w = 160 mm / 6.3” (B 160 S)w = 200 mm / 7.8” (B 200 S)w = 250 mm / 9.8” (B 250 S)w = 300 mm / 11.8” (B 300 S)
Joint chisel on rolls Brickwork, pavement joints
Hollow chiselJoint repair
Wide chisel w= 40 mm / 1.6”Pavement, tiles, plaster
Flat chisel w= 25 mm / 1”Brickwork
Moil pointConcrete, sand-lime bricks
Equipment-Sets for Floor and ParquetlayersB-Set XL-Set
Cutting-device with cutting bladePre-cutting floor coveringsand sealings
Technical Specifications
Further length deliverable / Handles replaceable
VOGT HammerOperating pressurePercussion rateAir consumption
61960/min255 l/min / 6,0 bar
3,0 - ,0 bar
Typ VH
Length
Weight
50-110.18
110 cm
5,4 kg
50-130.18
130 cm
5,8 kg
60-130.18
130 cm
6,4 kg
60-110.18
110 cm
6,0 kg
low vibration
lv
rai o
ow
ibt
n
Subject to technical modifications Print no. 01/2015·