Anchor Bay

Anchor Bay

Specialist suppliers to the building and construction industry

ContentsTying wires 4

Concrete spacers 5

Plastic spacers 6

Wire spacers 8

Fabric reinforcement 9

Bolt boxes, holding down bolts and grouts 10

Slab accessories 12

Polythene damp proof membranes 14

Resin anchor system 15

Joint fillerboards 16

Crack inducers and void formers 18

Surface treatment chemicals 19

Fosroc – waterproofing membranes 21

Waterstops – Fosroc range 22

Fosroc joint sealants 24

Grace – waterproofing membranes 26

Waterstop – Grace servicised range 28

Cetco – waterproofing system 29

Fosroc concrete repair 30

Concrete repair 31

Formwork tie rod system 32

Formwork accessories 34

Formwork chemicals 36

Monotub formwork systems 38

Formwork systems 39

Kwikastrip continuity system 40

Halfen HDB punching shear reinforcement 41

Formrib and rebar couplers 42

Concrete finishing tools 43

Concrete test equipment 44

Protection products 45

Halfen-brick tie products 46

Expamet brick tie products 48

Tools 50

Setting out products 52

Cut and bent reinforcements 53

Terms and conditions 54

Telephone 0870 24 24 234 Fax 0870 24 03 6134 Anchor Bay 2005

Black annealed tying wire

Stainless steel tying wire

Loop ties & tying tool

Tying wire nips

Tying wires

A soft black annealed 16 gauge wire

used for the tying of reinforcement.

18 gauge stainless steel tying wire used

for the tying of reinforcement.

An alternative way of tying reinforcement.

The tie is folded around the rebar and

tightened by the action of the tying tool.

The most popular tool used by all steel

fixers for the tying of reinforcement.

Code Pack

TW16 Coil

Code Pack

SS18 Kilo

Code Pack

WT150 1000

Wt/tool Each

Code Pack

Nips Each

Telephone 0870 24 24 234 Fax 0870 24 03 613 Anchor Bay 2005 5

Concrete spacers

Single cover spacers

Double cover spacers

Triple cover spacers

Concrete square bar

A concrete spacer designed to offer a

single cover to reinforcement ideally used

in horizontal applications.

Used for supporting reinforcement in

both vertical and horizontal applications.

Each block provides two separate

covers.

A concrete spacer used in vertical and

horizontal applications which offers three

separate covers.

A heavy duty bar spacer used for

supporting large reinforcement in heavy

duty slabs.

Code Cover Pack

SB20 20mm 1000

SB25 25mm 500

SB30 30mm 500

SB35 35mm 250

SB40 40mm 250

SB50 50mm 250

SB60 60mm 200

SB75 75mm 100

Code Cover Pack

SB15/20 15 & 20 1000

SB25/30 25 & 30 500

SB30/40 30 & 40 250

SB35/45 35 & 45 250

SB40/50 40 & 50 250

SB60/75 60 & 75 100

Code Cover Pack

SB20/25/30 20,25,30 500

SB35/40/50 35,40,50 250

Code Cover Pallet

20SQ20 20mm 1000

25SQ25 25mm 800

30SQ30 30mm 600

40SQ40 40mm 300

50SQ50 50mm 250

60SQ50 60mm 150

75SQ75 75mm 100


Code Cover Pack

TK15 15mm 100m

TK20 20mm 100m

TK25 25mm 100m

TK30 30mm 100m

TK35 35mm 50m

TK40 40mm 50m

TK50 50mm 50m

Code Cover Bar dia. Pack

20SW12 20mm 4 to 12 1000

25SW12 25mm 4 to 12 500

25SW20 25mm 8 to 20 500

30SW12 30mm 4 to 12 500

30SW20 30mm 8 to 20 500

35SW12 35mm 8 to 12 250

35SW20 35mm 10 to 20 250

40SW12 40mm 4 to 12 250

40SW20 40mm 8 to 20 250

50SW12 50mm 4 to 12 250

50SW20 50mm 8 to 20 250

Code Cover Pack

25MF30 25/30mm 1000

40MF50 40/50mm 250

65MF75 65/75mm 250

90MF100 90/100mm 100

Track spacer

Wheel spacers

Meshfix spacers

Plastic spacers

A continuous plastic spacer for

supporting bottom reinforcement in

suspended slabs. Also used on metal

because of its stability and excellent

concrete flow characteristics.

A robust clip-on plastic spacer wheel.

Ideal for the use on columns, walls and

beams. Offers minimum contact with

formwork.

A heavy duty double cover plastic spacer

designed to support mesh and rebar off

polystyrene insulation and polythene.

Membranes in ground slabs.



20NP20 20mm 8 to 20 1000

25NP20 25mm 8 to 20 1000

30NP20 30mm 8 to 20 1000

35NP20 35mm 8 to 20 500

40NP20 40mm 8 to 20 500

50NP20 50mm 8 to 20 500


50HD20 50mm 6 to 20 250

75HD20 75mm 6 to 20 100

Code Size Pack

(Horseshoe)

LS02 2mm 250

LS03 3mm 250

LS05 5mm 125

LS07 7mm 125

LS09 9mm 125

LS10 10mm 250

LS20 20mm 150

(Plain)

LS02P 2mm 250

LS03P 3mm 250

LS05P 5mm 125

LS07P 7mm 125

LS09P 9mm 125

LS10P 10mm 250

LS20P 20mm 150

Clip chair spacers

Pile cage spacers

Levelling shims

A heavy duty single cover spacer clip-on

chair spacer designed for all pre-cast and

site applications.

A heavy duty clip-on plastic wheel spacer

designed for in-situ piling and diaphragm

wall applications.

A hard plastic shim used for packing

during the alignment of precast panels.

Supplied in plain or horseshoe styles.

Horseshoe

Plain

Plastic spacers cont.


Code Cover Pack

DK50 50mm 50m

DK60 60mm 50m

DK75 75mm 50m

DK90 90mm 50m

DK105 105mm 50m

DK120 120mm 50m

DK135 135mm 50m

DK150 150mm 50m

DK165 165mm 50m

DK180 180mm 50m

DK200 200mm 50m

DK220 220mm 50m

DK230 230mm 50m

DK250 250mm 50m

DK270 270mm 50m

DK280 280mm 50m

DK300 300mm 50m

Code Cover Pack

CS50 50mm 25

CS60 60mm 25

CS75 75mm 25

CS90 90mm 25

CS105 105mm 25

CS120 120mm 25

CS135 135mm 25

CS150 150mm 25

CS165 165mm 25

CS180 180mm 25

CS200 200mm 25

Deckchairs

Hoop spacers

A welded girder used for supporting

fabric and reinforcement without

damaging the polythene membrane.

They can also be used to support dowel

bars. Supplied in 2 metre lengths.

A fast and economical way to support

mesh reinforcement in slabs. The hoops

are formed into a 1 metre diameter circle

and three or four hoops per sheet of

mesh is generally sufficient.

Wire spacers


Fabric reinforcement

Standard fabricManufactured to BS 4483 from cold reduced wire which complies with BS 4482.

Each wire intersection is resistance welded using electronically controlled techniques.

Standard sheet size: 4.8m x 2.4m

Merchant sheet size: 3.6m x 2.0m

Mesh size Cross sectional Nominal Sheets Sheet Sheets Sq. metres BS nominal pitch Wire sizes area per weight per weight per per ref. of wires meter width per m2 tonne (kg) bundle tonne Main Cross Main Cross Main Cross (kg) (approx) (mm) (mm) (mm) (mm) (mm) (mm)

A393 200 200 10 10 393 393 6.16 15 70.96 18 162.34 A252 200 200 8 8 252 252 3.95 22 45.50 28 253.16 A193 200 200 7 7 193 193 3.02 29 34.79 34 331.13 A142 200 200 6 6 142 142 2.22 40 25.57 46 450.45 A98 200 200 5 5 98 98 1.54 57 17.74 60 649.35

B1131 100 200 12 8 1131 252 10.90 8 125.57 10 91.74 B785 100 200 10 8 785 252 8.14 11 93.57 14 122.85 B503 100 200 8 8 503 252 5.93 15 68.31 18 168.63 B385 100 200 7 7 385 193 4.53 20 52.19 24 220.75 B283 100 200 6 7 283 193 3.73 24 42.97 30 268.10 B196 100 200 5 7 196 193 3.05 29 35.14 36 327.87

C785 100 400 10 6 785 70.8 6.72 13 77.41 16 148.81 C636 100 400 9 6 636 70.8 5.55 16 63.94 20 180.18 C503 100 400 8 5 503 49.0 4.34 20 50.00 26 230.41 C385 100 400 7 5 385 49.0 3.41 26 39.28 30 293.26 C283 100 400 5 5 283 49.0 2.61 34 30.07 32 383.14

D98 200 200 5 5 98.0 98.0 1.54 57 17.74 60 649.35 D49 100 100 2.5 2.5 49.1 49.1 0.77 113 8.87 50 1298.70

Standard sizes (4,800 x 2,400)

Mesh size Cross sectional Nominal Sheets Sheet Sheets Sq. metres BS nominal pitch Wire sizes area per weight per weight per per ref. of wires meter width per m2 tonne (kg) bundle tonne Main Cross Main Cross Main Cross (kg) (approx) (mm) (mm) (mm) (mm) (mm) (mm)

A393 200 200 10 10 393 393 6.16 23 44.35 26 162.34 A252 200 200 8 8 252 252 3.95 35 28.44 30 253.16 A193 200 200 7 7 193 193 3.02 46 21.74 50 331.13 A142 200 200 6 6 142 142 2.22 63 15.98 50 450.45

Merchant size (3,600 x 2,000)


Waxed cardboard bolt box

Polystyrene bolt box

Expanded metal bolt boxes

Holding down bolts

Made from waxed cardboard, they

provide an easy method of bolt alignment

for steel frame buildings.

An economical way of providing a void

around holding down bolts for steel

frame buildings.

Made from expanded metal for the

positioning of holding down bolts where

the bolt box is to remain in the concrete.

A range of high tensile grade 8.8 holding

down bolts complete with nuts and

washer plates 100 x 100 x 10mm

Bolt boxes, holding down bolts and grouts

Code Depth Taper

CB1 225mm 70 x 20

CB2 300mm 92 x 20

CB3 375mm 108 x 25

CB4 460mm 114 x 25

CB5 535mm 118 x 30

CB6 610mm 133 x 30

CB7 760mm 133 x 30

Code Depth

PC0 150mm

PC1 225mm

PC2 300mm

PC3 375mm

PC4 450mm

PC5 525mm

PC6 610mm

Code Description

DIS05 Disolver 5ltr

DIS25 Disolver 25ltr

Code Depth/Diameter

EXP0 150mm x 75mm

EXP1 225mm x 75mm

EXP2 300mm x 75mm

EXP3 375mm x 100mm

EXP4 450mm x 100mm

EXP5 600mm x 100mm

Code Size

20HDB300 M20 x 300mm

20HDB375 M20 x 375mm

20HDB450 M20 x 450mm

24HDB375 M24 x 375mm

24HDB450 M24 x 450mm


Non shrink grout

Cebex 100

Denso tape

A high strength non shrink cementitious

grout when added to water provides

excellent free flow properties for grouting

in holding down bolts.

Coverage: 13 litres/25kg approx.

Is an admixture for site batched

cementitious grouts where a reduced

water/cement ratio and positive

expansion is required.

Yield:

50kg of opc + 20-22 ltrs water

+ 225g cebex 100 = 36 litres

50Kg op opc + 22-24 ltrs water

+ 225g cebex 100 = 57 litres

Used to protect bolt heads prior to pouring concrete. Roll size: 75mm x 10m

Bolt boxes, holding down bolts and grouts cont.

Code Size/Detail

NSG25 25kg

PADDLE Mixing paddle

Code Size

COM100 24 x 225g

Code Size

DEN75 75mm x 10m


Slab accessories

Dowel bars

Dowel bar sleeves

Compression foam plugs

Dowel bar caps

Plain round mild steel dowel bars used in

contraction and expansion joints in slabs.

Other sizes available on request.

A flexible pvc sleeve which provides

a very efficient method of debonding

mild steel dowel bars. Meets with all

D.O.T. specifications.

A foam plug supplied separately for

insertion into dowel bar sleeves to allow

for expansion.

A rigid pvc tube with a compressible

filler one end which is designed to

allow for expansion of dowel bars in

construction joints.

Code Size

12DB900 12mm x 900mm

12DB1000 12mm x 1000mm

16DB400 16mm x 400mm

16DB600 16mm x 600mm

16DB900 16mm x 900mm

20DB500 20mm x 500mm

20DB600 20mm x 600mm

25DB600 25mm x 600mm

Code Size Pack

12DBS450 12mm x 450mm 100

16DBS450 16mm x 450mm 100

20DBS300 20mm x 300mm 100

20DBS450 20mm x 450mm 100

25DBS300 25mm x 300mm 100

32DBS375 32mm x 375mm 100

Code Size Pack

FP12 12mm 100

FP16 16mm 100

FP20 20mm 100

FP25 25mm 100

FP32 32mm 100

Code Size Pack

12DC100 12mm 100

16DC100 16mm 100

20DC100 20mm 100

25DC100 25mm 100

32DC100 32mm 100


Debonding compound

Dowel bar cradles

Plastic screed chairs

Metal screed chairs

Heavy duty metal screed chair

Screed chair rail

Code Pack

DB05 5ltr

DB25 25ltr

Expansion joint cage.

Contraction joint cage.

Code Product Pack

SC/SET Base,collar,saddle 100

T22 Shaft 100m

Code Slab thickness Pack

TUFF1 120mm - 150mm Each




Code Slab thickness Pack

HDSC 0mm - 500mm Each

Code Pack

S/RAIL 7.5m

Slab accessories cont.

A bitumen based compound used for

bond breaking of dowel bars in concrete.

Complies to Clause 2605 of D.O.E.

specification for roads and bridge works.

An accurate method used to support

dowel bars in contraction and expansion

joints in floor slabs and road construction.

An easily adjustable plastic screed

chair which is designed to be left in the

concrete part or whole. Suitable for

use with scaffold tubes or Anchor Bay

screeding rail.

For slabs 150mm-350mm.

A sturdy two component metal screed

chair for screeding slabs up to 400mm.

A heavy duty re-usable and fully

adjustable metal screed chair for slabs

up to 500mm. For long life wash and oil

after use.

Used in conjunction with screed chairs.

Size: 50mm x 25mm x 3mm

Length: 7.5 metre


Polythene DPM

Temporary protective sheeting

Jointing tapes

Geotextile

Terram

Polythene damp proof membrane

A polythene damp proof membrane

manufactured to BBA standards 97/3393.

Ideal as a temporary protective sheet.

Colour: opaque.

A 75mm wide tape designed for the sealing of

laps on polythene DPM’s. A double sided tape

used in the sealing of laps on polythene DPM’s.

A cost effective solution to the problem of

constructing stable granular layers over soft

foundation soils.

Terram nonwoven geotextile provides an

effective solution to the age old problem of

constructing stable granular layers over soft

foundation soils.

Code Gauge Roll size

500BBAB 500 4m x 50m

1000BBAB 1000 4m x 25m

1200BBAB 1200 4m x 25m

2000BBAB 2000 4m x 12.5m

Code Gauge Roll size

HDPS 65 4m x 25m

Code Size Pack

JT75 75mm x 33m 16

D/SIDE30 30mm x 30m 10

Code Roll size

GEOTEX 4.5m x 100m

Code Roll size

TERRAM/1 4.5m x 100m


Code Description

L/SETS25 Lokfix S25

L/SETP25 Lokfix P25

Code Description

EASI-CHEM Easi-chem 380ml

RESGUN Applicator gun

Code Description

SKELG Skeleton gun

CART Blank cartridge

P/PUMP Putzi pump


Resin anchor system

Fosroc Lokfix

Anchor Bay polyester resin

Application equipment

Calculation table

The two versions of lokfix are pre-

measured, two-part, filled polyester

resin grouts. After hardening, the grout

produces anchorages of consistent

reproducible values.

Lokfix S25 pour grade is for use where

the hole is 8 to 40mm greater in diameter

than the bar.

Lokfix P25 pump grade is used in

overhead or horizontal holes where the

hole is up to 25mm greater in diameter

than the bar.

A thixotropic low-slump polyester resin

grout for anchoring bolts, dowel bars,

starter bars, into vertical and sloping

plane concrete, rock and masonry.

Size: 380ml

A range of accessories used in the

application of resin grouts.

A guide table to calculate the volume of

resin grout required per hole.

Hole Bolt diameter diameter 12mm 16mm 20mm 25mm 32mm 38mm 44.5mm 51mm

20mm 0.020 litre

25mm 0.038 litre 0.029 litre

32mm 0.069 litre 0.060 litre 0.049 litre 0.031 litre

38mm 0.093 litre 0.082 litre 0.064 litre


51mm 0.155 litre 0.124 litre 0.091 litre


64mm 0.273 litre 0.241 litre 0.208 litre 0.166 litre 0.117 litre

76mm 0.298 litre 0.249 litre


Code Thickness

12FBS 12mm

20FBS 20mm

25FBS 25mm

Width 12mm 20mm 25mm

100mm 12FB100 20FB100 25FB100

125mm 12FB125 20FB125 25FB125

150mm 12FB150 20FB150 25FB150

175mm 12FB175 20FB175 25FB175

200mm 12FB200 20FB200 25FB200

225mm 12FB225 20FB225 25FB225

250mm 12FB250 20FB250 25FB250

Code Thickness

KORK/10 10mm

KORK/13 13mm

KORK/19 19mm

KORK/25 25mm

Joint fillerboards

Wood fibre fillerboard

Korkpak fillerboards

Is a compressible joint fillerboard

manufactured from bitumen impregnated

wood fibres. It is supplied in sheet

form and is used to form and fill

expansion joints in in-situ and pre-cast

concrete construction. Complies to

DTP specification for Highway Works

Dec 1991 Series 1000 Clause 1015

(Pavement Joints).

Sheet size 1.220m x 2.440m

Preformed bitumen bonded cork joint

fillerboard for critical water retaining, civil

and structural expansion joints.

Sheet size 2.0m x 1.0m.

Cut strips available on request.


Joint fillerboards cont.

Foam fillerboard

Hydrocell XL joint fillerboard

Adhesives

Is a closed cell polyethylene joint filler

for use as expansion joint filler in brick

and blockwork, isolation joints and hinge

joints where a readily compressible low

load transfer joint filler is required. Density

35kg/m3. Supplied in sheets and cut

strips with tear off.

Sheet size: 2.0m x 1.6m

A crossed linked, non absorbent,

semi-rigid, cellular polyethylene joint used

for forming expansion joints in concrete,

brickwork and blockwork. The product

provides excellent support to sealants

subject to hydrostatic pressure and is

particularly recommended for water

retaining or water excluding structures.

Density: 60 kg/m3. Sheet size: 1.8m x

0.9m. Cut strips available on request.

A contact adhesive designed for the

fixing of fillerboards to a wide range

of surfaces.

Code Thickness

10EXPS 10mm

12EXPS 12mm

15EXPS 15mm

20EXPS 20mm

25EXPS 25mm

30EXPS 30mm

Width 10mm 12mm 15mm

100mm 10EXP100 12EXP100 15EXP100

125mm 10EXP125 12EXP125 15EXP125

150mm 10EXP150 12EXP150 15EXP150

175mm 10EXP175 12EXP175 15EXP175

200mm 10EXP200 12EXP200 15EXP200

225mm 10EXP225 12EXP225 15EXP225

250mm 10EXP250 12EXP250 15EXP250

Width 20mm 25mm

100mm 20EXP100 25EXP100

125mm 20EXP125 25EXP125

150mm 20EXP150 25EXP150

175mm 20EXP175 25EXP175

200mm 20EXP200 25EXP200

225mm 20EXP225 25EXP225

250mm 20EXP250 25EXP250

Code Thickness

HDFS10 10mm

HDFS15 15mm

HDFS20 20mm

HDFS25 25mm

Code description unit

CONTACT Contact glue 1 ltr

CONTACT/5 Contact glue 5 ltr


Made from extruded PVC and used to

induce controlled cracking in concrete

slabs. Can be left in place omitting the

use of a joint sealant.

Used in the same application as one part

crack inducer but where the top section

can be removed after concrete has

cured to leave a void for sealant

10mm x 25mm.

Used to induce a controlled crack from

the underside of slabs. Can be used

in conjunction with either top crack

inducers or saw cutting.

A rigid reusable aluminium T-section used

to form a straight void in wet concrete to

accept top crack inducers.

A reusable rigid PVC void former used

in conjunction with fibre boards to create

a grove in wet concrete prior to sealing

with joint sealant.

Crack inducers and void formers

One part top crack inducer

Two part top crack inducer

Bottom crack inducer

Aluminium T-bar

Void formers

Code Size Pack

CI50 10mm x 50mm 5m

CI75 10mm x 75mm 5m

Code Size Pack

CI50/10 10mm x 50mm 5m

CI75/10 10mm x 75mm 5m

Code Size Pack

CY40 40mm 5m

CY75 75mm 5m

Code Size Pack

TB50 50mm 5m

TB75 75mm 5m

Code Size Pack

VH20 20mm x 10mm 3m

VF20 20mm x 20mm 3m

VH25 25mm x 12mm 3m

VF25 25mm x 25mm 3m


Code Size

CMG205 210ltr

CMG25 25ltr

Code Size

CM75/205 210ltr

CM75/25 25ltr

Code Size

CM90A/210 210ltr

CM90A/25 25ltr

Code Size

CM90R/210 210ltr

CM90R/25 25ltr

Surface treatment chemicals

Curing agent (standard)

Curing agent (75% efficienty)

Curing agent (90% aluminised)

Curing agent (90% efficienty)

A spray applied acqueous solution of

blended silicates designed to prevent

early drying out which enables the

cement to hydrate more efficiently,

considerably reducing the risk of surface

crazing and shrinkage whilst also giving a

stronger, more durable surface.

Coverage: 5.5-6m2/litre

A spray applied resin curing membrane

used to protect freshly placed or

formwork cast concrete from excessive

water loss during the critical curing period

and should be applied as quickly as

possible to ensure maximum benefit.

Coverage: 5m2/litre

A resin based curing membrane which

contains aluminium flakes which when

sprayed on the concrete surface

produces a metallic ‘mirror’ surface to

reflect away solar heat, this is particularly

advantageous on large expanses of

concrete such as airport runways and

concrete roadways.

Coverage: 5.5 m2/litre

A 90% efficiently resin based curing

agent which prevents premature drying

out of the concrete surface thus reducing

the risk of surface cracking.


Dustproof hardener

Bitumen emulsion

RIW L.A.C

RIW Flexiseal

RIW Toughseal

Surface treatment chemicals cont.

A solution used as a treatment on new

old concrete to give a superior surface

resistance to abrasion and cracking

attack with the added bonus of dust

reduction. Coverage: 6 m2/litre approx.

A cold applied rubberised bitumen

emulsion used as a protective damp

proof membrane to concrete and

brickwork. For best results two coats is

recommended. Coverage: 1.1-1.7m2/

litre per coat.

A spirit based bitumen emulsion used

as a water and water-vapour proof

membrane for foundation walls, floor

slabs etc. Coverage: 1m2/litre (2 coats).

1.25 m2/litre (steelwork) (2 coats)

A solvent free thixotropic liquid based on

urethane pre-polymers which on contact

with atmospheric moisture, cures to give

a continuous tough rubber like coating.

The material is supplied in the form of a

blue base coat and a black top coat.

Coverage: Base and top 1m2/kg

(2 coats). Primer 8m2/litre (1 coat)

A polymer modified epoxide coating

supplied as a two part pack of base and

hardener which cures to form a tough

black water and waterproof coating.

Coverage: 4m2/litre per coat.

Code Size

DPH205 210ltr

DPH25 25ltr

Code Size

BE205 210ltr

BE25 25ltr

Code Size

RIW205 205ltr

RIW25 25ltr

Code Description

FLEX/BB5 Blue base 5ltr

FLEX/BB25 Blue base 25ltr

FLEX/BT5 Black top 5ltr

FLEX/BT25 Black top 25ltr

FLEX/PR5 Primer 5ltr

FLEX/PR25 Primer 25ltr

Code Size

TOUGH/5 5ltr

TOUGH/20 20ltr


Fosroc – waterproofing membranes

Proofex 3000

Proofex engage

Proofex engage detail strip

Proofex lm

A high performance self adhesive

membrane for a range of waterproofing

applications including basements and

substructures. Proofex 3000 provides a

vapour and waterproofing membrane to

water excluding structures and protects

concrete from attack by aggressive

ground salts.

Roll size: 1m x 20m

Is a unique patented system comprising

a complex cell mesh bonded to a

polyethylene membrane which allows

poured concrete to interlock with

the membrane forming a tenacious

mechanical bond. Proofex engage is

supplied with a selvedge on one side to

provide sealed laps.

Roll size: 1.27m x 30m

A reinforced, double sided waterproofing

adhesive tape for sealing and jointing

roll ends, cut edges corner pieces, sold

in packs of two. It consists of a strong

synthetic fibre fabric impregnated and

coated both sides with a bitumen rubber

adhesive. Each side of the tape is

protected by a removable

siliconised paper.

Roll size: 200mm x 10m

Is a two component applied liquid

membrane for sealing around intricate

details such as pipe entries penetrations,

pile caps, etc. Coverage: approximately

4-6kg/m2 at normal loadings,

approximately 8kg/m2 where standing

water and pressurised water occur.

Code Description

WPM Proofex 3000

WPM/PR05 Proofex primer 5ltr

WPM/PR25 Proofex primer 25ltr

Code Description

PROF/ENG Proofex engage

Code Description

PROF/STRIP Proofex engage

detail strip

Code Description

PROOF/LM Proofex lm

PROOF/MESH Proofex lm mesh

50m x 100mm


Waterstops – Fosroc range

Supercast rearguard S250

Supercast rearguard S250 junctions

Supercast hydrofoil 250

When used on ground slabs where the

waterstop is supported on blinding,

Rearguard profiles usually require no

fixing. The waterstop is layed centrally

over the line of the joint to be formed.

Fixing to vertical shuttering is done by

nailing through the outer nailing flanges

leaving the head of the nail proud so

that it is held in the cured concrete. This

prevents the waterstop being displaced

when the shuttering is struck.

Roll size: 12 metre

A range of junctions for use with

supercast rearguard S250. Centre

bulb selections are used in expansion,

contraction joints.

The centre bulb allows for movements

in a structure to be accommodated

whilst its hexagonal design provides a

flat surface. This allows shuttering and

joint fillers to fit snugly. All centrally placed

supercast waterstops incorporate an

eyeletted, reinforced edge flange. This

enables them to be easily positioned by

wiring to surrounding reinforcement.

Roll size: 12 metre

Code Size

REAR/250 12m

Code Description

R250/FM Flat mitre

R250/F3W 3 way on flat

R250/F4W 4 way on flat

R250/INT90 Internal 90°

R250/EXT90 External 90°

Code Size

HYDRO/250 12m


A range of junctions used with

Supercast hydrofoil 250.

Jigs and knife used for on site

welding of supercast rearguard

250 and hydrofoil 250.

Integral sealing for construction joints

in concrete cast in-situ. Convenient and

problem solving in-situations where a

conventional waterstop would require

complex shuttering. Typical uses include

secant piled and diaphragm walled

basements, pile caps and casting against

old concrete.

Roll size: 15 metre

Waterstops – Fosroc range cont.

Supercast hydrofoil 250 junctions

Jig and knife

Supercast SW10

Code Description

S250/FM Flat mitre

S250/F3W 3 way on flat

S250/F4W 4 way on flat

S250/MOE Mitre on edge

250/TP T piece

Code Description

KNIFE 110v hot knife

JIG/REAR Rearguard jig

JIG/HYDR Hydrofoil jig

Code Description

SCAST/SW10 5mm x 20mm x 15m


Fosroc joint sealants

One part polysulphide

Two part polysulphide

Polysulphide primer

Two part polyurethane

Thioflex one is a one part, gun applied moisture

activated, polysulphide sealant. It is ideal for sealing

joints in window and door frame surrounds and as a

capping forbeaded glazing systems.

Conforms to BS 5215: 1986.

Cartridge size: 380mls

Colours: black, buff, mahogany, grey, stone,

cement white, white, brick red.

Thioflex 600 is available in gun and pouring grades.

The gun grade is ideal for general application, and is

available in a range of colours. It is packed in a ready

to mix 2.5 litre tin containing the base and curing agent

in the correct proportions. The pour grade for joints

in horizontal surfaces is supplied in grey only in 5 litre

packs with the base and curing agent in separate tins.

Conforms to BS 4254: 983, BS 6920:1996

Fosroc primer 7 is a one part chemically active

clear liquid for brush application to concrete, stone,

brickwork, timber and unglazed edges of

ceramic tiles prior to applying thioflex sealants.

Fosroc colpor 200PF is a high performance, pitch

free, pavement joint sealant. Used for the sealing and

maintenance of joints in concrete roads, concrete

runways and hardstandings. Colpor 200 PF is

particularly suitable for sealing areas where fuel and oil

spillage might occur such as aircraft fuelling areas, oil

terminals, garage forecourts, parking and cargo areas.

Conforms to BS 5212: 1990-types n, f and f b.

Colour: black

Code Pack

THIO/1 380mls

Code Pack

THIO/600G 2.5 Litre

THIO/600 5.0 Litre

Code Pack £/each

THIO/PR 500ml £12.28

Code Pack

COLPOR200 5 litre


Fosroc joint sealants cont.

Hot poured sealant

Foam backer rods

Accessories

Fosroc pliastic is a hot-poured rubber

bitumen horizontal joint sealant. Used for

sealing movement and construction joints

in pavements, floor slabs, water retaining

and water excluding structures.

Colour: black

Conforms to BS 2499: 1993 – pliastic N2

Yield: 19.6 Litre per pack

A closed cell polyethylene foam cord

used as a packing material for

joint sealants.

Tools and accessories used in the

application of joint sealing materials.

Mixing paddle: used for mixing sealants

Barrel gun: used for the placement of

bulk fill sealants. Supplied with three

different size nozzles.

Follower plate: designed to assist the

filling of barrel guns.

Cleaning solvent: a solvent based liquid

used for cleaning tools and barrel guns.

Gloves: a pvc knitted wrist glove

Bond breaking tape: used as a bond

breaker between joint sealant and

fibreboard. 25mm x 50m roll.

Code Pack

HPS20 20kg

Code Size Pack

BR6 6mm 1500m

BR10 10mm 1100m

BR12 12mm 900m

BR15 15mm 500m

BR20 20mm 300m

BR25 25mm 200m

BR30 30mm 150m

BR40 40mm 80m

BR50 50mm 50m

Code Pack

PADDLE Each

B/GUN Each

F/PLATE each

SOLV/5 5 litre

GLOVE 12 no.

B/TAPE 2550m


Grace – waterproofing membranes

Bituthene 3000

Bituthene 4000

Bituthene 8000

Bituthene liquid membrane

A self-adhesive, rubberized asphalt/

polyethylene waterproofing membrane.

Ideal for waterproofing concrete decks.


A self-adhesive hdpe waterproofing

membrane. Its cross laminated, high

density polyethylene carrier film provides

high tear strength and puncture and

impact resistance.


Bituthene 8000 combines the proven

bituthene adhesive technology with a

unique, grey coloured carrier film to

provide superior performance and easier

installation. It can be used horizontally or

vertically to protect basements and other

critical sub structures from the effects of

water, damp and gas.

Roll size: 1m x 20m

A two component, elastomeric, liquid

applied detailing compound for use with

grace waterproofing membranes.

Size: 5.7ltr

Code Description

B3000 Bituthene 3000

B1/PR05 B1 primer 5ltr


Code Description




Code Description




Code Description

BITU/LM Bituthene lm


Grace – waterproofing membranes cont.

Servipak protection board

Preprufe 300R and 160R

Preprufe tape

Durable, lightweight boards for

permanent protection of waterproofing

membranes from abrasive backfill, site

trafficking and reinforcement fixing.

Supplied in 3mm and 6mm thick sheets.

Sheet size: 2m x 1m

Is a pre-applied waterproofing membrane

that bond integrally to poured concrete

for use below slabs or behind basement

walls on confined sites.

Preprufe 300R is a heavy duty grade

for use below slabs and on rafts.

Designed to accept the placing of

heavy reinforcement using conventional

concrete spacers.

Preprufe 160R is a thinner grade for

lighter applications and blindside, zero

property line applications against soil

retention systems.

Roll size: Preprufe 300R 1.2m x 30m

Preprufe 160R 1.2m x 35m

Used for covering cut edges, roll ends,

penetrations and detailing.

Roll size: 100mm x 15m

Code Description

S/PAK03 3mm servipak

S/PAK06 6mm servipak

Code Description

PRE300R Preprufe 300R

PRE160R Preprufe 160R

Code Description

PRE/TAPE Preprufe tape


Waterstop – grace servicised range

Serviseal

Servitite

AT system

Jig and knife

Servistrip AH 205

An external PVC waterstop system

for passive protection of expansion,

construction and contraction joints in

reinforced concrete structures.

A high performance, internal PVC

waterstop for passive protection of critical

joints in reinforced concrete structures.

A high performance PVC waterstop

system with co-extruded hydrophilic

bulbs to provide a unique combination

of active and passive protection for joints

in concrete.

Jig and knife used for the on site welding

of waterstops

A solid, active jointing strip which swells

when exposed to water to prevent leak

paths in concrete.

Roll size: 20mm x 5mm x 10m

Code Description/size

SS195 Serviseal 195

SS240 Serviseal 240

SS320 Serviseal 320

Code Description/size

ST150 Std XJ 150mm

ST230 Std XJ 230mm

ST305 Std XJ 305mm

Code Size

AT200 200mm x

AT240 240mm x

Code Description

KNIFE 110v hot knife

JIG Jig

Code Description

AH205 Servistrip AH 205


Cetco – waterproofing system

Volclay voltex

Voltex accessories

Volclay granules

Volclay RX101 waterstop

Voltex is a highly effective waterproofing

composite of high strength geotextile and

4.88kg of sodium bentonite per square

metre. A patented needle-punch process

interlocks the geotextiles together

forming an extremely strong composite

that maintains the equal coverage of

bentonite, as well as protects it from

inclement weather and construction

related damage. Once backfilled,

voltex hydrates and forms a monolithic

waterproofing membrane. Voltex contains

zero voc, can be installed in almost any

weather condition to green concrete.

Roll size: 5.0m x 1.1m

Voltex nails and soft washers allows

direct shot-fired applications to secant

and contiguous piling, steel sheet piling,

diaphgregm wall, skin wall cast in-situ

and under blinding.

Pack size: 150

Stapler & staples used to secure laps

on sand or concrete underlining, or to

complement shot-fired fixings.

Pack size: 2500

Volclay granules are used to fill

cavities and voids in the substrate

prior to installing the main bentonite

waterproofing course. It is also used to

seal around slab penetrations to form a

continuous waterproofing system.

Pack size: 20kg

Waterstop RX101 is a sodium bentonite

based waterstop designed to stop water

infiltration through cast-in place concrete

construction joints by expanding upon

contact with water to form a positive seal

against the concrete.

Roll size: 5 metre

Code Description

VOLTEX Volclay voltex

Code Description

VOL/NAIL Voltex nails

Code Description

VOL/STPLR Stapler

VOL/STAP Staples

Code Description

VOL/GRAN Volclay granules

Code Description

RX101 Volclay rx101

REVOFIX Revofix 30m

RXWB RX WB adhesive


Fosroc concrete repair

Renderoc GP

Renderoc FC

Renderoc HB

Is a general purpose concrete

reinstatement mortar which can be used

as a render as well as for all types of

patch repairs. Renderoc GP is alkaline in

nature and will protect embedded steel

reinforcement. Renderoc GP is designed

for vertical, overhead or horizontal

applications. It can be applied up to

20mm thickness in sections overhead

and 30mm thickness in vertical sections.

Coverage: 16 litres/25kg bag

1.6m2 at 10mm thickness

Is designed for application in thin layers

to produce a fair-faced appearance

to concrete surfaces in readiness to

receive a protective/decorative coating.

Renderoc FC is designed for vertical and

overhead use to infill honeycombing and

voids up to 3mm deep in the surface of

concrete.

Coverage: 15 litres/25kg bag

5.0m2 at 3mm thickness

For the reinstatement of large areas

of concrete and for small, localised

patch repairs. Renderoc HB is alkaline

in nature and will protect embedded

steel reinforcement it is specifically

designed for vertical and overhead

high-build applications. Renderoc HB

can be applied in sections up to 80mm

thickness in vertical locations and up to

50mm thickness in overhead locations

in a single application and without the

use of formwork. Coverage: 14.5-15.0

litres/18kg 15m2 at 10mm thickness

Code Size

REN/GP 25kg

Code Size

REN/FC 25kg

Code Size

REN/HB 18kg


Code Colour Size

FAS/GR25G Grey 25kg

FAS/GR Grey 8kg

FAS/GR/25W White 25kg

FAS/WH White 8kg

Code Size

FIL/RUB25 25kg

Code Size

SBR05 5 litre

SBR25 25 litre

Code Size

PVA05 5 litre

PVA25 25 litre

Code Description


C/STONE Carborundum stone

P/FLOAT Plastic float

W/FLOAT Wooden float

M/FLOAT Metal float

BUCKET Site pvc bucket

GLOVE PVC knit wrist gloves

BRUSH Turks head brush

Concrete repair

Fastpatch cement

Fill ‘n’ rub

SBR bonding agent

PVA bonding agent

Ancillary products

A prepacked specialised repair cement,

based on the latest polymer cement

technology, it provides a simple, cost

effective rapid repair system for in-situ

and precast concrete, masonry, screeds,

renders, brickwork and blockwork.

Colours: grey and white. Coverage: 1kg

yields 500cm3 or 2.1kg/mm/m2

A convenient method of filling blow holes

and small surface defects in precast

or in-situ cast concretes, as well as

providing an even standardised colour

and aesthetic finish.

Is a styrene butadiene emulsion for

use as an admixture in cementitious

compounds. It will improve many of the

properties of the compound such as

improving strength, excellent adhesion,

wear resistance, waterproof and weather

resistance and shrinkage. Full technical

details available on request.

A versatile and non-toxic ready to use

PVA bonding and sealing adhesive giving

a strong but flexible bond with high

moisture and mould resistance. Typical

uses: priming, woodworking, concreting,

floor laying, plastering and rendering,

tiling, painting and decorating.

A range of products for the use with

concrete repair products.


Formwork tie rod system

Formwork tie rod

Wing nuts

Waler plates

Tie rod connectors

Water barrier connectors

Rock anchor

A self cleaning high tensile steel tie rod

designed for use with formwork. Available

in 15mm and 20mm diameters.

Used in conjunction with waler plates to

secure tie rods in formwork.

A high quality pressed plate used in

conjunction with tie rods and wing nuts

to secure formwork.

Dimensions: 100 x 100 x 10mm to suit

15mm tie rod 120 x 120 x 20mm to suit

20mm tie rod.

A jointing nut used to connect two

tie rods together with a centre stop

to ensure equal spacing inside the

connector. Length: 105mm

Used in water retaining structures.

Cast into the concrete wall between

two separate tie rods. After pouring

tier rods are removed and water barrier

remains in-situ.

Used for securing single sided formwork

in concrete or rock walls.

(37Mm drill bit)

Code length

TB15 6.0M

TB15/1.5 1.5M

TB15/1.2 1.2M

TB15/3 3.0M

TB20 6.0M

Code Size

WN15 15mm

WN20 20mm

Code Size

WP15 15mm

WP20 20mm

Code Size

JN15 15mm

Code Size

WB15 15mm

WB20 20mm

Code Size

RA15 15mm


Formwork tie rod system cont.

Cast in anchor

Weldable anchor

Tie rod sleeve

Tie sleeve cones

Flupps

Tie plug cement

Wedge anchors

A plastic cast in anchor which is secured

to formwork and cast into initial pour

to provide an anchor for tie rod in

subsequent pours.

An anchor which can be welded to

structural steel beams ,sheet piling

and other metal structures to accept

15mm tie rod. Anchors must be welded

continuously all the way round – load

tests should be conducted before use.

A rigid pvc tube used as a spacer

between formwork and also allows tie rod

to be removed easily.

A pvc cone used on both ends of tie rod

sleeves which can be easily removed

after formwork is struck.

Used in conjunction with tie plug cement

to give a water tight seal in areas where

tie rod’s have been removed.

A cement specially developed for

plugging and waterproofing of tie holes

in concrete walls.

A m16 x 65mm drop in anchor used for

anchoring props in concrete.

Code Size

C/ANCHOR 15mm

Code Size

WELD/ANCHOR 15mm

Code Size Pack

T22 22/26mm 100m

T26 26/30mm 50m

Code Size Pack

BC22 22mm 500

BC26 26mm 500

BC22/50 22/50mm 125

BC26/50 26/50mm 125

BC/TOOL 1

Code Size Pack

FLUPP 22mm 500

FLUPP26 26mm 250

FLUPP32 32mm 125

Code Pack

TP8 8kg

Code Description Pack

WEDGE M16 x 65mm 25


Formwork accessories

Plastic corner fillets

Wooden corner fillets

Formwork magnets

Formwork tape

Grout check foam

An extruded rigid pvc section which can

be nailed to formwork or column shutters

to form chamfered corners. Supplied with

or without nailing flange.

A wooden section which can be nailed

to formwork or column shutters to form

chamfered corners.

A magnet used for removing wire and

nails from shutters prior to concreting.

A pvc tape used for the sealing of joints in

formwork to prevent grout loss. Roll size

50mm x 33m

Designed for use on all types of

formwork. Grout check foam is a closed

cell polyethylene foam with a high

pressure adhesive on one side used for

sealing joints in formwork to prevent grout

loss. Available in two sizes:

6mm x 12mm x 10m.

12mm x 24mm x 5m.

Code Size Pack

CF11 11mm 100m

CFN11 11mm 100m

CF15 15mm 100m

CFN15 15mm 100m

CF20 20mm 100m

CFN20 20mm 100m

CF25 25mm 100m

CFN25 25mm 50m

CF30 30mm 50m

CFN30 30mm 50m

Code Size Pack

CF20W 20mm 100m

CF25W 25mm 100m

Code Pack

MAGNET 2

Code Pack

FTR50 30 rolls

Code Size Pack

6F12 6 x 12mm 25 no.

12F24 12 x 24mm 12 no.


Formwork accessories cont.

Silicone sealant

Handy foam

Fire retardant handy foam

Bright round wire nails

Formwork plugs

Steel adjustable kickers

Plastic kickers

A clear high modulus silicone sealant

in 310mls which can be used for filling

movement joints in formwork.

An aerosol packed polyurethane foam

which expands when released used

for filling gaps in formwork and other

construction areas.

A fire retardant aerosol packed

polyurethane foam which prevents the

transmission of smoke, seals around

pipework, insulates against noise, heat or

cold. Conforms to din 4102 part 1 class

b1. CFC free.

A high quality bright round wire nail.

Supplied in 20kg boxes.

A plastic conical shaped plug used for

the filling of redundant tie holes in timber

shutters.

Designed to eliminate the need to pour

a kicker.

Code Pack

S/310 25

SKELG 1

Code Pack

FHP750 12

Code Pack

FRF750 12

Code Size Pack

NAIL/50 50mm 20kg

NAIL/65 65mm 20kg

NAIL/75 75mm 20kg

NAIL/100 100mm 20kg

NAIL/150 150mm 20kg

Code Size Pack

F/PLUG11 11mm 1000

F/PLUG20 20mm 1000

F/PLUG22 22mm 1000

F/PLUG26 26mm 1000

Code Size Pack

KICK/150 150mm 100

KICK/175 175mm 100

KICK/200 200mm 100

KICK/225 225mm 100

KICK/250 250mm 100


P/KICKER Plastic kicker 100

Plastic formwork kickers are used to secure

formwork at the base of walls. They are

supplied with a masonry nail which can be

placed with the aid of a hilti gun.


Formwork chemicals

Mould oil

Chemical release agent

Surface retarder

Formwax sealer

A general purpose mould oil with good

release qualities. For use on all types

of formwork. Can be brush or sprayed

applied.

A general purpose chemical release

agent which provides excellent release

and surface finish. Reduces blowholes,

staining and surface blemishes.

Mould applied (code SRG25) brushed

onto formwork, it is designed to give

an exposed aggregate surface which

gives an excellent key for subsequent

concreting. Surface applied (code

SRS25) sprayed onto fresh concrete to

give an exposed aggregate finish.

Formwax is specifically developed for

the initial sealing of various formwork

surfaces. Based on crystalline waxes and

with a fugitive dye which will not stain

permanently, this thixotropic material

when worked into a surface takes on

a smooth, thin paste consistency. Its

economy of use, speed of application

and compatibility with most types

of release agent make it the ideal

preservation sealer.

Coverage: 10m2/kg approx.

Code Size

MO205 205

MO25 25

Code Size

CRA205 205

CRA25 25

Code Size

SRG25 25

SRS25 25

SRS205 205

Code Size

FW20 20kg


Formwork chemicals cont.

Shutter repair compound

Formwork plugs

Sprayers

Barrel accessories

A quick setting two part polyester filler

used for filling holes and damaged areas

on wood, fibreglass or metal formwork.

It is easily worked and sanded and is

compatible with release agents.

A plastic conical shaped plug used

for the filling of redundant tie holes

in timber shutters.

High performance sprayer units for the

application of mould oil and chemical

release agent.

Taps and pumps used in conjunction with

plastic and metal barrels.

Code Size

SFO8 8kg

SFH1 Each

Code Size Pack

F/PLUG11 11mm 1000

F/PLUG20 20mm 1000

F/PLUG22 22mm 1000

F/PLUG26 26mm 1000

Code Description

MS08/S 8ltr metal sprayer

PS08 8ltr plastic sprayer

KN20 20ltr knapsack

NOZZ Nozzle

LANCE Sprayer lance

TRIGGER Sprayer trigger unit

GASK/M Metal gasket set

GASK/P Plastic gasket set

SOLV/5 Cleaning solvent 5ltr


Code Description

TAP 3/4’’ barrel tap

PUMP Barrel pump


Monotub formwork systems

Monotub

Monotub accessories

Is a disposable formwork for rapid

construction of circular and square

concrete columns.

Advantages:

• Fast and economical to use

• 100% water resistant and can be

stored outside without damaging the

quality of the tube.

• Light and easy to handle.

• Quick and easy to erect

• Provides the optimum fair face finish

concrete column.

• Requires no mould oils or release

agents.

• Stripped literally in seconds.

• Very strong

• Can be used for horizontal void

forming. Manufactured in a large range

of sizes.

• Delivered at short notice.

(Popular sizes typically 24/48 hours)

Products used to assist with the erection

of monotub tubes.

Code Diameter

MONO150 150mm

MONO200 200mm

MONO240 240mm

MONO250 250mm

MONO300 300mm

MONO350 350mm

MONO400 400mm

MONO450 450mm

MONO500 500mm

MONO550 550mm

MONO600 600mm

MONO650 650mm

MONO700 700mm

MONO800 800mm

MONO900 900mm

MONO1000 1000mm

MONO1200 1200mm

Code Dimension

MONO/200S 200mm x 200mm





Code Details

M/STRAP Multistrap

MONO/KICK Kicker


Code Thickness

CLAY/50 50mm

CLAY /75 75mm

CLAY/100 100mm

CLAY/125 125mm

CLAY/150 150mm

CLAY/175 175mm

Code Thickness

CLAY/60 60mm

CLAY/85 85mm

CLAY/110 110mm

CLAY/160 160mm

Code Description

25POLY 25mm polystyrene

50POLY 50mm polystyrene

100 POLY 100mm polystyrene

Formwork systems

Claymaster

Cellcore

Clayboard

Polystyrene sheets

Is a low density expanded polystyrene,

designed to compress under load and

so reduce the lateral forces of ground

movement on the foundation.

Sheet size: 2.4m x 1.2m.

Thickness: 50mm-300mm

Consists of a honeycomb of inter-

locking sections made from expanded

polystyrene. Designed so as ground

movement occurs cellcore compresses

and buckles to accommodate it, thereby

reducing the forces that would otherwise

be transmitted to the foundations. It

is used extensively in both residential

and commercial applications to protect

piled beams and rafts, heavy slabs and

reinforced ground floor slabs.

Sheet size: 2.44m x 1.22m.

Grades: CC & CP full technical

information available on request.

Is a unique, environmentally friendly void

former and foundation stabiliser made

from a biodegradable honeycomb core

set between lightweight polypropylene

facings. When dry clayboard is strong

enough to support the weight of wet

concrete and steel reinforcement.

Sheet size: 2.440m x 1.0m. Full

technical information available on request.

A SDN grade expanded polystyrene

board used to as thermal insulation and

void former in walls and ground floor

slabs. Can be cut accurately with the aid

of a fine tooth saw to any shape or size.

Sheet size: 2.44m x 1.2m (8’ x 4’).

Other thickness available on request


Kwikastrip continuity system

The Kwikastrip reinforcement continuity

system has been fi rmly established

over many years as the contractor’s

fi rst choice. This results from consistent

delivery of an almost infi nitely variable

product within a very short lead-time.

To further reassure engineers, Kwikastrip

is supported by the highest level of

technical endorsement in the form of

UK CARES Technical Approval.


Halfen HDB punching shear reinforcement

Halfen HDB punching shear reinforcement

is designed to prevent punching failure

at column heads in concrete flat slab

construction – without the traditional

need for downstand beams, mushroom-

headed columns and thickened floors.

The system is manufactured from ribbed bars

which are hot-forged to make double-ended

studs (connected by spacer rails) to provide

virtually slip-free shear head reinforcement

with excellent anchorage. The two or three-

stud elements are simply dropped into place

in the reinforcing cage and retained in position

by means of clip bars and/or tying wire. This

typically reduces site installation time from hours

to minutes per column head compared

to traditional bent reinforcement.

To facilitate selection and use, a specially-written

software programme that calculates shear stress

and reinforcement requirements is available.

The HIT System is the latest development in

thermal break and reinforcement continuity

for cantilevered balcony construction.

HIT helps to eliminate the effects of cold

bridging (i.e. condensation and mould

growth) experienced with reinforcement

that is traditionally continuous from internal

slab straight through to external balcony.

The HIT System comprises special stainless

steel swaged couplings in the tension zone

(into which is factory-fitted normal high-

yield reinforcement) and stainless steel

double-headed studs in the compression

zone. These stainless steel components

are housed in a high-density polystyrene

fabrication which provides the thermal

separation between floor slab and balcony.

The HIT System is supplied in versions

for in-situ and precast applications and

modules of 1.0m and 0.2 metres that can

be used in combination to avoid cutting.

Halfen HDB Punching Shear Reinforcement

Halfen HIT Insulated Balcony Connection System


Formrib and rebar couplers

Formrib permanent shuttering

MBT couplers

Halfen HBM couplers

A galvanised expanded metal used

widely in the construction industry as a

permanent shuttering for stopends. It

is manufactured from hot-dipped zinc

coated steel sheet to BS EN 10142

1991. Sheet size: 3m x 0.445m

The MBT range of couplers provides

a cost effective method of joining

reinforcing bars particularly when the

fixed bar is already in place. They can

be installed without any preparation to

the bar ends and without any need to

rotate bars.

The HBM system consists of high-

strength couplers factory-swaged onto

grade 500 high-yield reinforcement bars.

Anchorage reinforcement (female socket

bars) can be supplied in shapes and

lengths to suit almost any application

configuration. The male connection bar

has a hot-forged ‘upset’ end onto which

is rolled a standard metric thread.

HBM is hallmarked by off-the-

shelf availability and CARES

Technical Approval.

Code Description

FORMRIB/3 3m x 0.445m

Code To suit rebar

MBT10 T10

MBT12 T12

MBT16 T16

MBT20 T20

MBT32 T32

MBT40 T40

Bar diameter 10mm 12mm 16mm 20mm 25mm 32mm 40mm

External diameter d 33.4 33.4 42.2 48.3 54 71 81

Total length l 100 140 160 204 258 312 484

Socket size A/F (ins) 1/2 1/2 1/2 1/2 5/8 5/8 3/4

No. of bolts 4 6 6 8 8 10 14

Approx. weight (kg) 0.52 0.72 1.25 1.96 3 6.5 11.3


Concrete finishing tools

Easy float (fresno)

Easy float handle

Concrete rake

Concrete finishing brush

Hand floats

Tamping beam

Carborundum stone

A zinc plated steel float incorporating

radius arms and a texturing broom for

brush work. The broom is a polybristle

medium texture. Floats have radius ends

to prevent lap marks.

Size: 1200mm (4ft).

An aluminium snap extension handle

used in conjunction with easy floats.

Size: 1800mm (6ft)

The tools are lightweight and of rugged

construction and are designed to

allow the placement of concrete where

required. The tooth side is for raking

and the smooth side is for floating

and screeding.

Primarily used for concrete texturing on

motorways, airport aprons and taxiways.

A range of floats used for the placing and

floating of concrete.

An aluminium box section beam used for

tamping and levelling concrete. Supplied

either with or without handles.

Length: 6000mm. Other lengths

available on request.

A carborundum rubbing block used

to smoothen out uneven concrete

repaired surfaces.

Code Description

E/FLOAT1200 1200mm fresno

Code Description

E/HANDLE Handle 1800mm

Code Description

C/RAKE Concrete rake

Code Description

F/BRUSH600 600mm wide

F/BRUSH900 900mm wide

Code Description


M/FLOAT Metal float


Code Description

T/HANDLE Handles

Code Description



Concrete test equipment

Cube moulds

Curing tank

Slump cone

Scoop

Wire brush

Max/min thermometer

A high quality four part design cube

mould with meets requirements of

BS1881 part 108, EN12390-1 and

ISO1920

A curing tank which can take up to

30 x 150mm cube moulds, made from

polyethylene and measuring 990mm x

686mm x 635mm overall. Fitted with a

220 volt 3kw heater but also works on

110 volt (heating taking a little longer)

fitted with mechanical thermostat and

a galvanised mesh lower rack. The

thermostat is factory set to control the

tank at 20°C. It is ideal for site use where

an economical solution is required. Meets

standard BS 1881 part 111 EN 12390-2.

Designed to measure the workability of

concrete. This is carried out by filing the

slump cone with fresh concrete in three

layers, tamping each one and levelling

to the top of the cone. The slump cone

is then removed and the distance the

concrete falls or ‘slump’ is measured

with the rule.

An aluminium scoop for use with cube

moulds and other test equipment.

A construction duty wire brush.

A quick set push button thermometer for

use on site.

Code Size

CM100 100mm

CM150 150mm

T/BAR Tamp bar

Code Description

C/TANK Curing tank

Code Descritpion

SLC Slump cone

SL/ROD Slump cone rod

B/PLATE Base plate

Code Description

SCOOP Scoop

Code Description

W/BRUSH Wire brush

Code Description

THER Max/min thermometer


Protection products

Rebar caps

Frost blanket

Hessian

Temporary protective sheeting

Brick acid

Corner fenders

Gloves

Protection sheet

A high visibility safety cap designed to

fit over the end of protruding rebar to

reduce the risk of injury.

A 10mm closed cell polyethylene foam

designed to give good protection to

concrete during low temperatures. They

also make excellent curing mats during

warmer temperatures as well.

Hessian rolls used for the protection and

covering up of masonry and concrete.

A polythene sheeting used for covering

up and protection of building goods

on site.

Is a selected blend of inorganic

acids for the removal of cementitious

contamination and rust from a wide range

of surfaces.

Designed to protect corners on columns

in areas of builds which are prone to

heavy trafficking such as multistorey car

parks. Available with tangs for casting

into concrete or with pre-drilled holes for

surface fixing after the column is cast.

A general purpose knit wrist pvc glove

used for general protection of hands

while handling building materials.

A 2mm corrugated polypropylene sheet

which is easy to cut, crease or curve

to any site requirement. Available in

standard or fire rated grades.

Sheet size: 2.44m x 1.22m (8’ x 4’).

Code Rebar size Pack size

SBP16 6mm-18mm 250

SBP32 16mm-32mm 250

SBP40 25mm-40mm 100

Code Size

FRO/BL 75m x 2m x 10mm

Code Size

HESSIAN 1350mm x 46m

Code Size

HDPS 4m x 25m

Code Description

BRICK/05 Brick acid 5ltr

Code Description

C/FENDER 50mm x 50mm x 1.2m

Code Pack

GLOVE 12 pairs

Code Pack

PS02 Sheet

PS02FR Sheet



RIB/100S 100mm stainless 100

RIB/150S 150mm stainless 100

RIB/3000S 3000mm stainless Each

RIB/100G 100mm galv 100

RIB/150G 150mm galv 100

RIB/3000G 3000mm galv Each


HTS/B/75S 75mm stainless 100





HTS/B/75G 75mm galv 100





Halfen-brick tie products

Ribslot 28/20

HTS-B channel brick ties

HTA and HZA cast in channels

Halfen ribslot 28/20 is a self-anchoring

channel which has been designed to

achieve minimum deflection. It is available

in grade 304 stainless steel (S304) and

a pre galvanised steel. Sizes available:

100mm, 150mm and 3000mm.

Halfen HTS-B channel ties are designed

to bed into the mortar at one end and

have a shouldered head that locates into

a cast-in or surface fixed channel at the

other end available in grade 304 stainless

steel (S304) and a pre galvanised mild

steel. Sizes available: 75mm, 100mm,

150mm, 175mm & 200mm.

A cold rolled channel with anchors

designed for casting into concrete.

The channel with its anchors, is attached

to the formwork before casting. The

void within the channel is filled with

granulated expanded polystyrene which

keeps the inside of the channel free from

concrete during pouring and which is

easily removed when fixings are to be

made. Full technical literature available on

request. Types available: HTA 28/15,

HTA 38/17, HTA 40/25, HZA 41/22.

Standard lengths 3050mm & 6070mm.

Cut lengths available on request.

Grades available: A2 stainless steel and

galvanised mild steel.


HTS-C cavity brick ties

HTS-W wire ties

HTS-FS frame cramps

Halfen HTS-C cavity ties have been

designed to meet the design and

performance requirements of DD140.

These ties are designed for a normal

10mm mortar bed. HTS-C ties come in

standard shapes and lengths which will

cover most applications.

Grades available: stainless steel grade

304 (S304). Galvanised mild steel.

Halfen HTS-W wire ties are suitable for

cavities up to 100mm. They are available

in stainless steel grade 304 only. HTS-W2

tie meets DD140 type 2 requirements

and complies to DD140 type 4.

Lengths available: 200mm & 225mm

Halfen HTS-FS frame cramps are ties

that bed into the mortar joint at one end

and are surface fixed to the structure

through an upstand at the other end.

HTS-FS frame cramps come in standard

shapes and lengths which will cover

most applications. Available in stainless

steel grade 304 (S304). Sizes: 75mm,

100mm, 125mm, 150mm, 175mm

and 200mm.

Halfen-brick tie products cont.


Expamet brick tie products

Expamet multi starter

Exmet brick reinforcement

Expamet brickstrength

Featuring a ‘turn-n-slide’ tie which

enables the starter to be tied into any

course the builder wishes, ideally every

(225mm deep) block course or every

third (75mm deep) bricks. Supplied in

pack form only. Pack contents: Two

1165mm stainless steel lengths, ten ties,

five screws, wall plugs and washers

An expanded stainless steel metal

manufactured to BS EN 10088-1: 1995:

1.4301 (Grade 304/S15). Where greater

strength is required to allow for uneven

settlement and movement in buildings it

is desirable to use exmet reinforcement in

the joints.

Reinforcement for mortar bed joints in

brickwork. Manufactured from stainless

steel type BS EN 10088-1,1.430.

Code Description

M/STARTER Mutli starter kit

Code Description

BMESH65 65mm exmet

BMESH115 115mm exmet

BMESH175 175mm exmet

B/MESH225 225mm exmet

Code Description

BRICK60 60mm brickstrength





Width (mm) Length (mm) Wire diameter (mm)

60 3050 4

100 3050 4

150 3050 4

175 3050 4

200 3050 4

Material Coil size Coil size Suitable for minimum thickness (mm) width (mm) length (mm) wall thickness (mm)

0.3 65 20 75

0.3 115 20 140

0.3 175 20 190

0.3 225 20 250


Frame crampA safe edge frame cramp which provides

positive location of window and door

frames to masonry manufactured from

pre-galvanised steel strip with zinc

coated edges to BS EN 10142: 1991.

Code Description

F/CRAMP100 100mm x 50mm



Expamet brick tie products cont.

Width (mm) Length (mm) Upstand (mm) Quantity/Box (mm)

28 100 50 250

28 150 50 250

28 200 50 250


Tools

Wire brush

Mixing paddle

Skeleton gun

Turks head brush

Scoop

Sprayers

Barrel accessories

A construction duty wire brush.

Used for the mixing of non shrink grouts

and other powders. Manufactured to suit

all heavy duty electrical drills.

An application gun used to dispense

products from 310ml cartridges.

Used for the application of bitumen

emulsion, primers and other liquids to

concrete surfaces.

An aluminium scoop for use with cube

moulds and other test equipment.

High performance sprayer units for the

application of mould oil and chemical

release agent.

Taps and pumps used in conjunction with

plastic and metal barrels.

Code Description

W/BRUSH Wire brush

Code Description


Code Description

SKELG Skeleton gun

Code description

BRUSH Turks head

Code Description

SCOOP Scoop

Code Description

MS08/S 8ltr metal sprayer

PS08 8ltr plastic sprayer

KN20 20ltr knapsack

NOZZ Nozzle

LANCE Sprayer lance

TRIGGER Sprayer trigger unit

GASK/M Metal gasket set

GASK/P Plastic gasket set



Code Description

TAP 3/4’’ barrel tap

PUMP Barrel pump


Tools cont.

Carborundum stone

Hand floats

Buckets

Tying wire nips

Scraper

Utility knife

Cranking Irons

A carborundum rubbing block used to

smoothen out uneven concrete

repaired surfaces.

A range of floats used for the placing

and floating of concrete.

A heavy duty PVC site bucket.

The most popular tool used by all steel

fixers for the tying of reinforcement.

Used for cleaning residue concrete from

formwork panels.

A heavy duty utility knife pack which

includes holder and spare blades.

A tool used for the straightening of rebar.

Available in three sizes to cover a range

of rebar diameters.

Code Description


Code Description


M/FLOAT Metal float


Code Description

BUCKET Site bucket

Code Pack

NIPS Each

Code Pack

SCRAPER/LONG Each

Code Description

S/KNIFE Utility knife set

Code Description

CRANK 14-16mm rebar

CRANK/20 18-20mm rebar

CRANK/26 25mm rebar


Setting out products

Line marking spray

Plastic barrier fencing

Fencing pins

Hazzard tape

An aerosol spray used for marking or

lining areas on site. Available in colours

yellow, red, blue and white and packed 6

750ml cans per box.

A heavy duty highly visible orange

polythene barrier fencing supplied in rolls.

Roll size 1m x 50m

A mild steel pin , pointed one end and a

curled lamp hook on the other. Size: 1.35

metre long.

A white and red diagonally warning tape

supplied in 500 metre rolls.

Code Colour

LINE/Y Yellow

LINE/R Red

LINE/B Blue

LINE/W White

Code Size

BARRIER 1m x 50m

Code Size

F/PIN 1.350M

Code Size

BARRIER/TAPE 500m


Reinforcing bar to bs 4449 and cut and bent to BS8666:2000, supplied in high yield grade

460n/mm2 and plaind round to grade 250n/mm2.

Size 8mm 10mm 12mm 16mm 20mm 25mm 32mm 40mm

Kg/m 0.222 0.395 0.888 1.579 2.466 3.854 6.313 9.864

12m/tonne 211 135 94 53 34 22 13 8

Cut and bent reinforcements

Shape codes to BS 8666:2000

00

11

12

13

15

21

25

26

31

33

41

44

46

51

67

77

All other shapes are shape code 99 and require a fully dimensional sketch


1. GENERALThe following Terms & Conditions apply to all agreements entered by the company for the Manufacturer and supply of its goods and services. No variation of our addition to the terms shall be valid unless authorised in writing by a Director of the company.

2. QUOTATIONSA quotation does not constitute an offer. No contract is concluded until written confirmation by the company is sent on receipt of order.

3. PERFORMANCES AND SPECIFICATION Any performance estimate is given without commitment and is based upon the company’s experience only. Whilst every effort is made to ensure the accuracy of the details in our catalogue this is subject to a general acceptance of minor errors and omissions.

4. PRICEPrices quoted are based upon current conditions, costs of labour materials and statuary charges and are subject to increase without notice to take account of variations or alterations of the same. The company accordingly reserves the right to adjust invoice prices in the event of any increase in the cost of materials, transport or of labour and/or take account of any other costs that may arise in result of legalisation or by reason of any other event unknown to the company at the date of quotation.

5. PAYMENT The payment terms in the company’s quotation must be strictly adhered to. In the event that payment is not made by the due date, the company shall be entitled to charge the customer interest on any overdue amount at the rate of 2% per month (or at such other rate as may be advised by the company from time to time). For each month or part month, which the said amounts, are to remain overdue. The customer shall not be entitled to retain, deduct or defer any sums whatsoever due to the company under the contract on account of any dispute, cross claim or set-off which it might have with the company. Non-compliance with payment terms will entitle the company to withhold further deliveries and/or labour forthwith. The company’s delivery notice/invoice copy receipted on behalf of the customer or such other reasonable evidence as may be declared shall be sufficient proof of delivery for this purpose.

6. OWNERSHIP AND RISK (i) The risk of damage to any goods shall pass to the customer on delivery.(ii) Title to any goods shall not pass to the customer until the company has received

payment in full of all accounts under each and every contract between the company and the customer existing at delivery. In the meantime, the goods shall remain property of the company and the customer shall hold them in a fiduciary capacity as the company’s bailee free from any charge, lien or other encumbrance. During this period:

(a) the customer shall keep the goods or any other property into which they are incorporated fully insured with a reputable insurer and if possible, store them separately and/or keep them in such a way that they can be clearly identified as the company’s property; and

(b) the company shall be entitled to recover possession of the goods (or any of them) at anytime to lawfully enter upon any of the customer’s (and for any reason) (and even by

severance from other property) shall be entitled without restriction to lawfully enter upon any of the customer’s premises for that purpose. The customer shall pay all costs and expenses incurred by the company in exercising this right.

(iii) Not withstanding that title may not have passed to the customer, the company may maintain an action for the price of the goods and the customer acknowledges that nothing in sub clause (ii) above confers any right to upon it to return or reject the goods or refuse, defer or delay payment from them.

7. DELIVERY AND [LIEN] (i) Although the company will use reasonable commercial endeavours to deliver goods

within any time estimates given, time of delivery is not the essence of the contract and delay shall not therefore entitle the customer to repudiate. Neither shall the company be liable to the customer for any loss or damages whatsoever suffered or sustained as a result of the company failing to adhere to such times or dates.

(ii) The company shall be entitled to deliver by single delivery or instalments. Without prejudice to sub clause (i) above, non-delivery of any instalment or delay in delivery shall not affect the balance of the contract or entitle the customer to terminate the same. However, the company shall be entitled to levy additional charges where the customer fails or refuses for any reason to take delivery and shall be entitled to determine the contract forthwith if the customer the fails to take delivery within fourteen days of a written request requiring them to do so.

(iii) The company shall upon notice to the customer be entitled to withhold delivery or suspend performance of the contract generally if at the time of the notice any credit limit extended to the customer has been exceeded or payment of any of the company’s invoices (whether related to the contract or not) is then overdue. If the customer fails within fourteen days of the notice to reduce its indebtedness to the level requested or to settle the said invoices, then the company shall, without further notice to the customer, be entitled to determine the contract forthwith.

(iv) In addition to the above, the company shall (without prejudice to any other remedy available to it) have in respect of all unpaid debts and other sums due from the customer under the contract a general lien on any goods whatsoever in its possession (whether in relation to the contract or otherwise) which are or are intended to become the property of the customer and pursuant to that lien or right the company shall be entitled upon fourteen days written notice to the customer to sell any goods so held upon such terms as it thinks fit and to keep the proceeds of sale thereof in diminution of the sum due to it and all costs and expenses incurred in or about effecting the sales.]

8. FAULTY GOODS AND LIMITATION ON LIABILITY(i) Whilst all reasonable care is taken in compiling technical data on the company’s products

all recommendations or suggestions regarding the use of such products are made without guarantee since the conditions of use are beyond the control of the company. It is the customer’s responsibility to satisfy them that each product is fit for the purpose for which they intended to use it and the actual conditions of sale are suitable.

(ii) Not withstanding that it will not be responsible for any defects caused or sustained as a result of variations in the customer’s original specifications, the company warrants that its goods will be of satisfactory quality and that all service it provides by it will be performed with reasonable skill and care. Accordingly, the company will replace any goods that are defective, damaged or faulty at its own expense (provided that they have not been tampered with or subjected to improper treatments by the customer) if the customer gives written notice of the faults and defects within seven days of delivery. Goods to be replaced must be returned to the company properly packed and carriage paid before any replacement will be issued and notwithstanding clause 6(ii) hereof, goods so returned become the property of the company.

(iii) Save as hereinbefore provided the company shall not be liable to compensate for indemnify the customer for any loss or damage (whether direct, indirect, consequential or otherwise) to or caused by or sustained as a result of the goods or services provided

(iv) Not withstanding anything hereinbefore contained, the company is not seeking to exclude or restrict its potential liability for damage in the nature of death or the negligence or that of its servants or agents causes personal injury. However, the customer shall indemnify the company against all actions, claims, proceedings losses, costs, damages and expenses whatsoever arising in respect of loss of life or personal injury suffered by any person in connection with the contract where that loss of life or personal injury is caused by negligence of the customer or of its servants or agents.

(v) A film of rust or mill scale on reinforcement will not constitute grounds for rejection.

9. CANCELLATIONThe customer may not cancel all or any part of the contract without the written consent of the company.

10. INTELLECTUAL PROPERTY The patent, registered design, copyright and any other intellectual property rights attached to all goods and component parts, drawings, designs and plans of such goods are actually invented or designed by the company shall remain vested and the customer shall not therefore be entitled to copy to reproduce or procure the copying or reproduction of the same without the company’s written consent.

11. FORCE MAJEURE In the event the normal course of the contract is frustrated, prevented, Interrupted, hindered delayed or rendered unduly expensive by any cause whatsoever beyond its control, the company shall promptly give notice thereof to the customer and shall have the right to cancel the contract or to defer its performance for as long as such force majeure shall continue.

12. PROPER LAW The construction, validity and performance of the contract shall be governed by English Law and all disputes shall govern the construction, validity and performance of the contract or the English Courts shall decide questions that may arise out of or in connection with or in relation to the contract.

1. Carriage paid on all orders except: (i) Orders less then £300 in invoice value and are subjected to a £20.00 delivery charge. (ii) Orders dispatched at the customer’s request by express delivery/courier,

carriage at a cost.2. Deliveries are provided to customer’s requirements by or own transport.3. Deliveries are usually delivered within 48 hours of receipt of order for ex-stock items.4. All prices in the catalogue are exclusive of VAT5. The catalogue price list replaces all other price lists.6. All sales are subject to our standard terms and conditions of sale.7. Whilst all reasonable care is taken in complying technical data on the company’s

products are made without guarantee since the conditions of use are beyond the control of the company. It is the customer’s responsibility to satisfy himself that each product is fit fir the purpose for which he/she intends to use it and that actual conditions of use are suitable.

DELIVERY TO NEAREST HARD ROAD TO SITE Errors and omissions accepted. This applies to all aspects of our catalogue.

ANCHOR BAY CONSTRUCTION PRODUCTS LTD & ANCHOR BAY BEAM FORMUNIT C79 BANNING STREET GREENWICH LONDON SE10 ONT

Terms and Conditions

Quality products on time every time

Anchor Bay Construction Products Limited Unit C, 79 Banning Street, London SE10 ONT

T: 0870 24 24 234 F: 0870 24 03 613 [email protected] www.anchor-bay.co.uk

Anchor Bay

Documents

Transcript of Anchor Bay