Analysis and optimization of wireless power transfer link
-
Upload
ajay-kumar-sah -
Category
Technology
-
view
727 -
download
2
Transcript of Analysis and optimization of wireless power transfer link
International Conference on Technology and Innovation Management
and IOE Graduate Conference
Oct 10-11, 2014
Analysis and Optimization of Wireless Power Transfer Link
Ajay Kumar Sah
Dr. Dibakar Raj Pant
Outline
• Introduction
• Problem Statement
• Objective
• Methodology
• Radiation and safety level
• Conclusion
• Future Work
• Scope/Application
• References
2International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Introduction: What is Wireless Power Transfer
(WPT)?
• Types are:
3
Figure 1: Types of WPT System
The transmission of power from
one place to another without
using wires, cables or chords.
International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Problem Statement
• When the distance between Tx & Rx changes,
there is the frequency splitting issue which
substantially deteriorates the power transfer
efficiency of the WPT System.
4
• Users have to plug in
their electronic devices
when the battery runs
out so are not truly
portable.
International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Objective
• Analysis and optimization of wireless powertransfer link for maximum power transferefficiency
5
Block diagram of the system
Figure 2: Basic Block diagram of 4 coil WPT Link
International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Methodology
6
Figure 3: (a) Simplified schematic (b) Equivalent circuit of 4 coil antenna system
International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Methodology: Design of Class-E Power Amplifier
7
Class-E power
amplifier has
high efficiency,
fewer components
and yielding high
reliability[1].Figure 4: Class E power amplifier
It consists of a RF choke Lc, a switch T1, a shunt
capacitor (which includes the transistor capacitance)
Cs, a load networks L-C and a load RL.
International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Methodology: GaN HEMT
• GaN HEMT is a High Electron Mobility Transistor.
• The compound Gallium Nitride is a very hard material.
• Its wide band gap of 3.4 eV affords it special properties
for applications in optoelectronic, high-power and high-
frequency devices.
• Due to high mobility of carrier electron, HEMT has very
low stray capacitance such as Cgs and Cds .
• Low Cgs enables high frequency gate drive with low
input power.
• Low Cds enables low switching loss for switched power
supplies.
8International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Design of GaN HEMT Class-E Power Amplifier
• Setting Vcc to 5V, RL to 1 Ohm, Lc to 100uH and QL
to 10 and using Equations in [16] gives the
component values displayed in Table 1.
• The switch is replaced by GaN HEMT enhancement
type MOSFET transistor, EPC1010
• VPULSE input is used to drive the transistor
9
Table 1: Design Limits of GaN HEMT Class E Amplifier
International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Design of GaN HEMT Class E Power Amplifier
10
Figure 5: GaN class e amplifier PSpice Schematic
Figure 6: Transient analysis of GaN class e amplifier
It can be seen
from the figure
6, the input to
the class E
amplifier is 5v
square wave
and the output is
160v sine wave
which is better
than h-bridge
amplifier used
in [20].
International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Simulation of 4 Coil WPT Link
• 4 Coil WPT Link is simulated on Advanced
Design System (ADS) as shown in figure 7.
11
Figure 7: Equivalent circuit of WPT system on ADS
International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Analysis of frequency splitting phenomena
12
• At remote distances, the efficiency peaks only at the resonant
frequency.
• Closer distance leads to frequency splitting.
• The shorter the transfer distance, more obvious the phenomena is.
•When the distance
between transmitter and
receiver changes, the
coupling coefficient (k)
also varies and the
resonant frequency
(13.56MHz) splits as
shown in figure 8.
Figure 8: Frequency splitting phenomena
International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Frequency splitting & Cause Analysis
• At close distances, the input impedance at the original resonant
frequency point is characteristic of extremely large impedance
angle and relatively low amplitude.
• Large impedance angle causes very low transferred power, and
much is exchanged between the Power and the transmitter Coil.
• Small amplitude results in a large source current, thus increasing
the source internal resistance loss.
• Both these two factors reduce efficiency.
• While at below and above the original resonant frequency, the
input impedance is characteristic of extremely small impedance
angle and relatively high amplitude.
• Due to the opposite characteristics, efficiency peaks at these two
frequency points.
13International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Related Factors of Frequency splitting
• The related factors, i.e. the source internal
resistance (Rs), the mutual inductance between
the Power coil and the Transmitter coil (M12),
and the mutual inductance between the load coil
and the receiving coil (M34)[23].
• When the source internal resistance increases, the
input impedance is changed into small amplitude
and large impedance angle.
• This leads to Frequency splitting.
14International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Related Factors of Frequency splitting
Mutual Inductance of Source & Transmitter Coil
15
It can be seen from the figure 8
that decreasing the coupling
coefficient k23 between
transmitter & receiver coil i.e.
bringing the transmitter and
receiver closer keeping the k12
& k34 fixed,
efficiency of the system decreases and frequency splitting takes
place. When the coupling between power coil and transmitter coil
k12 increase from 0.1 to 0.2 i.e. bringing the power coil and
transmitter coil closer eliminates the frequency splitting
phenomena and the efficiency of the system increases.
Figure 9: Power transfer efficiency at
different coupling coefficient
International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Related Factors of Frequency splitting
• Mutual Inductance of Load & Receiver Coil
16
It can be seen from the figure 10 that
decreasing the coupling coefficient k23
between transmitter & receiver coil i.e.
bringing the transmitter and receiver
closer keeping the k12 & k34 fixed,
efficiency of the system decreases and
frequency splitting takes place.
When the coupling between receiver coil and load coil k34 increase from 0.1 to
0.25 i.e. bringing the receiver coil and load coil closer eliminates the frequency
splitting phenomena and the efficiency of the system increases.
Figure 10: Power transfer efficiency at
different coupling coefficient
International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Comparative Study on Antenna Topology
• Here using the same parameters as used in series-series topology, a
mixed topology called LCC topology is shown in figure 11.
17
The resonant frequency of this
circuit, neglecting internal resistance
of the coil is calculated as:
𝑓 =1
2𝜋 𝐿 𝐶1 + 𝐶22
Where,
L= Parallel Inductance, C1= Series Capacitance, C2= Parallel
Capacitance
Figure 11: LCC Topology
International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Comparative Study on Antenna Topology
18
Figure 12: Power transfer efficiency at different k for LCC & Series-series topology
In series-series topology, aslight variation of 0.006 incoupling coefficient causes thesystem efficiency to drop to 15% and also frequency splittingtakes place.
On the other hand, thechange of 0.025 in couplingcoefficient of LCC topologyonly causes a change of 20%i.e. a decrease from 80% to60% in the link efficiency.
International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Comparative Study on Different Wire Gauge of Antenna
• The skin depth is defined as:
𝛿 =2
𝜔𝜎𝜇3
• With 𝜎=5.96 x 107 for copper. For f=13.56 MHz, the skin depth is≈ 18𝜇𝑚.
• For the study purpose American Gauge Wire AWG14, 18 and 22are selected.
• Using same inductance and capacitance of all the antennas, theother parameters like coil antenna length, diameter, and resistanceare calculated using equations in [8-9].
• The study can be summarized as: Helical antenna 1 (0.5≤ FormFactor ≤ 0.6), Helical antenna 2 (1≤ Form Factor ≤ 1.65) andSpiral Antenna
19International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Helical antenna 1 (0.5≤ Form Factor ≤ 0.6)
• The parameters of helical antenna 1 withvarying wire gauge are given below in table 2
20
An
ten
na
Ind
uct
anc
e (
uH
)
Co
re
Dia
me
ter
(mm
)
Pit
ch
(mm
)
Nu
mb
er
of
Tu
rns
Form
Fact
or
An
ten
na
Len
gth
(cm
)
Wir
e
Len
gth
(cm
)
Re
sist
anc
e (
m-
oh
m)
AW
G
Wir
e
Po
we
r
0.5 60
10 3 0.55 3.5 58.1 4.8 14
10 3 0.55 3.3 57.5 11.95 18
10 3 0.5 3.2 57.15 30.2 22
Tran
smit
t
er
1.3 80
10 4 0.6 4.65 1.5 8.45 14
10 4 0.6 4.4 100 21.2 18
10 4 0.55 4.25 100 53.55 22
Re
ceiv
er
0.4 80
18 2 0.55 3.9 51.3 4.25 14
18 2 0.55 3.8 50.9 10.6 18
18 2 0.55 3.75 50.65 26.75 22
Load 0.1 60
21 1 0.5 2.25 19.35 1.6 14
22 1.5 0.5 4.6 28.75 6 18
22 1.5 0.5 4.55 28.6 15.1 22Table 2: parameters of helical antenna1 with varying wire gauge
International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Helical antenna 1 (0.5≤ Form Factor ≤ 0.6)
• The simulation result of maximum efficiency of wireless
power transfer link using AWG 14, 18 and 22 wire for
helical antenna 1 is shown in figure 13 and both
calculated & simulated are shown in table 3.
21
Helical antenna (0.5≤ Form Factor ≥0.6)
Wire Gauge
Efficiency (%)
CalculatedSimulation
AWG 22 64.64 64.59
AWG 18 82.81 82.67
AWG 14 92.35 92.34
Table 4: Efficiency comparison of
helical antenna1 at varying wire gauge
Figure 13: Power transfer efficiency of
different wire gauge
International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Helical antenna 2 (1≤ Form Factor ≤ 1.65)
• The parameters of helical antenna 2 with
varying wire gauge are given below in table 4.
22
An
ten
na
Ind
uct
ance
(uH
)
Co
re
Dia
me
ter
(mm
)
Pit
ch (
mm
)
Nu
mb
er o
f
Turn
s
Form
Fac
tor
An
ten
na
Len
gth
(cm
)
Wir
e L
en
gth
(cm
)
Re
sist
ance
(m-o
hm
)
AW
G W
ire
Po
we
r
0.5 60
20 4 1.45 8.65 77.45 6.4 14
20 4 1.4 8.4 76.7 15.95 18
20 4 1.4 8.25 76.2 40.25 22
Tran
smit
te
r 1.3 80
15 5 1.05 8.3 130 10.55 14
15 5 1 8 125 26.5 18
15 5 1 7.8 125 66.95 22
Re
ceiv
er
0.4 80
32 3 1.2 10.1 76.95 6.35 14
32 3 1.2 9.9 76.35 15.9 18
32 3 1.2 9.8 76 40.15 22
Load 0.1 60
52 2 1.65 10.7 38.7 3.2 14
52 2 1.65 10.6 38.35 8 18
52 2 1.65 10.55 38.1 20.15 22
Table 4: parameters of helical antenna 2 with varying wire gaugeInternational Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Helical antenna 1 (1≤ Form Factor ≤ 1.65)
• The simulation result of maximum efficiency of wireless
power transfer link using AWG 14, 18 and 22 wire for
helical antenna 2 is shown in figure 14 and both
calculated & simulated are shown in table 5.
23
Figure 14: Power transfer efficiency of
different wire gauge
Helical antenna (1≤ Form Factor ≥1.65)
Wire GaugeEfficiency (%)
Calculated Simulation
AWG 22 55.20 55.13
AWG 18 76.39 76.30
AWG 14 89.3089.13
Table 5: Efficiency comparison of
helical antenna2 at varying wire gauge
International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Methodology: Spiral Antenna
• The parameters of spiral antenna with varying wire gauge are given below in table 6.
24
An
ten
na
Ind
uct
ance
(u
H)
Co
re D
iam
ete
r
(mm
)
Th
ickn
ess
(m
m)
Nu
mb
er o
f La
yers
Co
il D
ep
th (
mm
)
Wir
e L
en
gth
(cm
)
Re
sist
ance
(m
-
oh
m)
AW
G W
ire
Po
we
r
0.5 60
2 2 3 39.6 3.25 14
2 2 1.9 38.9 8.1 18
1 1.5 1.2 28.85 15.25 22
Tran
smit
t
er
1.3 80
2 2.5 4.45 66.3 5.45 14
2 2.5 2.8 65 13.55 18
1 2.5 1.75 64.2 33.95 22
Re
ceiv
er
0.4 80
2 1.5 3 39.1 3.25 14
2 1.5 1.9 38.6 8.05 18
1 1.5 1.2 38.25 20.2 22
Load 0.1 60
2 1 1.6 19.35 1.6 14
2 1 1 19.15 4 18
1 1 0.65 19.05 10.05 22
Table 6: parameters of spiral antenna with varying wire gauge
International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Methodology: Spiral Antenna
• The simulation result of maximum efficiency of
wireless power transfer link using AWG 14, 18 and
22 wire for spiral antennas is shown in figure 15 and
both calculated & simulated are shown in table 7.
25
Spiral antenna
Wire Gauge
Efficiency (%)
Calculated Simulation
AWG 22 71.74 71.58
AWG 18 86.86 86.56
AWG 14 94.30 94.15
Figure 15: Power transfer efficiency of
different wire gauge
Table 7: Efficiency comparison of
spiral antenna at varying wire gauge
International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Radiation and Safety Level
• Power transfer takes place due to magnetic induction,
so non-radiative.
• Moreover, Certain frequencies like 6.78MHz and
13.56MHz are designated by the ITU for industrial,
scientific and medical (ISM) RF applications
• At these frequencies, Special International Committee
on Radio Interference (CISPR) 11 places no limits on
RF emissions [7].
26International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Conclusion
• From the observations and analyses done so
far in this thesis, it can be concluded that the
use of AWG 14 wire, spiral antenna and LCC
topology gives the best efficiency in the
Wireless Power Transfer Link.
• In addition to this, it has been observed that
GaN HEMT class E amplifier has better
performance than h bridge amplifier in the
Wireless Power Transfer Link
27International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Future Work
• The prototype of wireless power transfer link with
class E amplifier, spiral antenna using AWG 14
wire in LCC topology can be developed to verify
the theory and to discuss the realizable
performance of implemented WPT link using
vector network analyzer (VNA).
28International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Scope/Application
• Some probable field where it can be used for
wireless powering & charging are:
Implantable medical devices (ventricular assist
devices, pacemaker, defibrillator, etc.)
High tech military systems (Wireless sensors,
unmanned mobile robots, etc.)
Consumer electronics (phones, laptops, game
controllers and etc.)
29International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
References1. W. Chen, R. A. Chinga, S. Yoshida, J. Lin, C. Chen, and W. Lo, “A 25.6 W 13.56 MHz
wireless power transfer system with a 94% efficiency GaN class-E power amplifier,”
Microwave Symposium Digest (MTT), 2012 IEEE MTT-S International, pp. 1–3, August 2012.
2. William C. Brown, "The history of wireless power transmission," Solar Energy, vol.56, no.1,
pp. 3-21, January 1996.
3. Kurs, A. Karalis, R. Moffatt, J. D. Joannopoulos, P. Fisher and M. Soijacic, “Wireless Power
Transfer via Strongly Coupled Magnetic Resonances,” Massachusetts Institute of Technology,
2007 Science, Vol. 317. no. 5834, pp. 83— 86, July 2007.
4. Zhang, Xiu, S. L. Ho, and W. N. Fu. "Analysis and Optimization of Magnetically Coupled
Resonators for Wireless Power Transfer," IEEE Transactions on Magnetics, vol. 48, no.11,
pp.4511-4514, November 2012.
5. Chen, Linhui, Shuo Liu, Yong Chun Zhou, and Tie Jun Cui, "An optimizable circuit structure
for high-efficiency wireless power transfer," IEEE Transactions on Industrial Electronics, vol.
60, no. 1, pp.339-349, January 2013.
6. Nadakuduti, Jagadish, Lin Lu, and Paul Guckian, "Operating frequency selection for loosely
coupled wireless power transfer systems with respect to RF emissions and RF exposure
requirements," In Wireless Power Transfer (WPT), 2013 IEEE, pp. 234-237. IEEE, May 2013.30International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
References7. Karalis, Aristeidis, John D. Joannopoulos, and Marin Soljačić. "Efficient wireless non-
radiative mid-range energy transfer." Annals of Physics 323.1, pp. 34-48, January 2008
8. Babic, Slobodan I., Frederic Sirois, and Cevdet Akyel. "Validity check of mutual inductance
formulas for circular filaments with lateral and angular misalignments." Progress In
Electromagnetics Research M, vol. 8, pp. 15-26, 2009
9. Grover, Frederick W. "The calculation of the mutual inductance of circular filaments in any
desired positions." Proceedings of the IRE 32.10, pp. 620-629, 1944
10. Lundin, Richard. "A handbook formula for the inductance of a single-layer circular
coil." Proceedings of the IEEE 73.9, pp. 1428-9, 1985
11. Grover, Frederick W. Inductance calculations: working formulas and tables. Courier Dover
Publications, 2004.
12. http://en.wikipedia.org/wiki/American_wire_gauge
13. Nilsson, James William., and Susan A. Riedel. Electric Circuits. Boston: Prentice Hall, 2011.
31International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
References14. Kawamura, Atsuo, and Tae-Woong Kim. "Proposed Equivalent Circuit and Parameter
Identification Method for Electro-Magnetic Resonance Based Wireless Power Transfer.” April
2013
15. Beh, TeckChuan, et al. "Wireless Power Transfer System via Magnetic Resonant Coupling at
Fixed Resonance Frequency―Power Transfer System Based on Impedance Matching―."
Proc. The 25th World Battery, Hybrid and Fuel Cell Electric Vehicle Symposium &
Exhibition (EVS25). November 2010.
16. Sokal, Nathan O. "Class-E RF power amplifiers." QEX Commun. Quart 204, pp. 9-20, 2001
17. de Rooij, Michael A., and Johan T. Strydom. "eGaN FETs in Low Power Wireless Energy
Converters." ECS Transactions 50.3, pp. 377-388, 2013
18. Uchiyama, Hiroyuki, et al. "Consideration of impact of GaN HEMT for class E
amplifier." TENCON 2010-2010 IEEE Region 10 Conference. IEEE, 2010.
19. http://epc-co.com/epc/documents/datasheets/EPC1010_datasheet.pdf
20. Sah, Ajay Kumar and Timalsina, Arun. “Design of Simple Wireless Power Transfer System viaMagnetic Resonant Coupling at 13.56MHz.” Proceedings of IOE Graduate Conference, Vol. 1,pp. 206-210, November 2013
32International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
References21. Yang, Ching-Wen, and Chin-Lung Yang. "Analysis on numbers and adaptive ranges of
resonators for efficient resonant coupling wireless power transmission." Wireless Power
Transfer Conference (WPTC), 2014 IEEE. IEEE, 2014.
22. Zhang, Y., Zhengming Zhao, and Kainan Chen. "Frequency Splitting Analysis of Four-Coil
Resonant Wireless Power Transfer.", Energy Conversion Congress and Exposition (ECCE),
2013 IEEE , pp. 1-1, September 2013
23. Yiming Zhang, Zhengming Zhao and Kainan Chen, "Frequency splitting analysis of
magnetically-coupled resonant wireless power transfer," Energy Conversion Congress and
Exposition (ECCE), 2013 IEEE , pp.2227-2232, 15-19 September 2013.
24. Y. Zhang, Z. Zhao and K. Chen, "Frequency decrease analysis of resonant wireless power
transfer," IEEE Trans. Power Electron., vol. 29, no. 3, pp. 1058-1063, Mar. 2014.
25. Waters, Benjamin H., et al. "Optimal coil size ratios for wireless power transfer
applications." Circuits and Systems (ISCAS), 2014 IEEE International Symposium on. IEEE,
2014.
26. Yan, Zhuo, et al. "Influence Factors Analysis and Improvement Method on Efficiency of
Wireless Power Transfer Via Coupled Magnetic Resonance."Magnetics, IEEE Transactions
on 50.4, pp. 1-4, 201433International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
References27. Choi, Hyo-Jin, Sangbin Lee, and Cheolung Cha. "Optimization of geometric parameters for
circular loop antenna in magnetic coupled wireless power transfer." Wireless Power Transfer
Conference (WPTC), 2014 IEEE. IEEE, 2014.
28. Sample, Alanson P., David A. Meyer, and Joshua R. Smith. "Analysis, experimental results,
and range adaptation of magnetically coupled resonators for wireless power transfer," IEEE
Transactions on Industrial Electronics, vol. 58, no. 2, pp. 544-554, February 2011.
29. Hwang, Hyeonseok, et al. "An analysis of magnetic resonance coupling effects on wireless
power transfer by coil inductance and placement." Consumer Electronics, IEEE Transactions
on 60.2, pp. 203-209, 2014
30. Fu, Minfan, et al. "Subsystem-level efficiency analysis of a wireless power transfer
system." Wireless Power Transfer Conference (WPTC), 2014 IEEE. IEEE, 2014.
31. Zhang, Yiming, Zhengming Zhao, and Ting Lu. "Quantitative Analysis of System Efficiency
and Output Power of Four-Coil Resonant Wireless Power Transfer." IEEE Transactions on
Power Electronics, pp. 1-1, 2013.
32. Jonah, Olutola, "Optimization of Wireless Power Transfer via Magnetic Resonance in
Different Media," Ph.D. Thesis, FIU Electronic Theses and Dissertations, Paper 876, March
2013.
34International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
References33. Pozar, David M. Microwave engineering. John Wiley & Sons, 2009.
34. Jordan, Edward C., and K. G. Balmain. Electromagnetic Waves and Radiating Systems.
Second ed. New Dehli: Prentice-Hall of India, 2006. Print.
35International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014
Thank You !
36International Conference on Technology and Innovation Management and IOE Graduate Conference, Oct 10-11, 2014