Amazon Web Services - Dynam Skytrainer 182 Manual · 2019. 5. 21. · PA 2.5*8mm screws. Install...
1
DYE-1004 40A ESC ASSEMBLY: Install the propeller. 1 2 3 4 5 6 7 8 9 10 11 12 13 15 16 17 18 19 20 14 Install the landing gear cover with Double-sided tape. 16 17 Skytr-15 Decal DY-1007 9g Servo DYR-2001 2.4G Receiver DY-3003 Glue SPARE PART LIST: BM2815A-KV1100 Brushless Motor BM2815A-KV1100-Shaft Motor Shaft DECAL: Skytr-02 Wing Skytr-04 Elevator Skytr-03 Vertical Stabilizer Skytr-09 Landing Gears Skytr-07 Spinner DY8938 Dynam RC dynam-rc.cn of This product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Please recycle. over CENTER OF GRAVITY(C.G.) DIRECTIONS FOR ASSEMBLY AND ADJUSTMENT Wingspan Length Flying Weight Wing Area Wing Load Radio System Power Battery : 1280mm (50.4in) : 1000mm (39in) : 1000g (35.3oz) : 23dm² : 43.5g/dm² : 4 Ch TX and 7 Ch RX : Brushless System : LIPO, 2200 mAh, 11.1V Control Throw Setting Suggestion Elevator Aileron Rudder 11.1V 2200mAh Li-Po, 20C (9060x3) ESC-30A ESC-40A Lithium-polymer Battery 2200mAh 14.8V 20C Discharge Rechargeable Cells Use li-po charger only MOTOR DY-6006 11.1V 2200mAh 20C Battery DYAT-008 Servo Horn DY-3001 Quick-Controller Skytr-01 Fuselage Skytr-05 Wing Back Cowl Skytr-06 Cowl Skytr-14 Bolt Pipe Connect the pushrod on the rudder and secure the screw (the servo should be in the center position) . Connect the pushrod on the elevator and secure thescrew (the servo should be in the center position) . Connect the aileron servos with the Y wires. Connect the direction pushrod. ( The servo should be in center position) 55 60 55 60 11 8 9 2 5 12 3 6 1 13 4 15 7 10 16 17 Slide the nose gear into the slot on the bottom of the fuselage. Use a hexagon screwdriver to tighten the screw. Remove the tape from both sides of the fuselage head. Install the cowl . Install the landing gear with PA2.5*8mm screws. Install the horizontal stabilizer and vertical stabilizer. Secure the stabilizers with PA2.3*20mm screw. Install the spinner with PA2* 6mm screws. Apply glue on the antenna and insert it into the main wing as shown. Apply glue on the contact area of the left and right wing. Glue the left and right main wings together. Secure the wing onto the fuselage with PA2.3*20mm screws. Secure the wing struts with PA 2.5*8mm screws. Install the battery. DYT-2002 4CH Transmitter DY-3007 Flap hinges Skytr-08 Plastic Part Set Skytr-10 Canopy Skytr-11 Push Rod Skytr-12 Wing Struts Skytr-13 Propeller Skytr-16 Plastic Tab Skytr-17 Screw set
Transcript of Amazon Web Services - Dynam Skytrainer 182 Manual · 2019. 5. 21. · PA 2.5*8mm screws. Install...
DYE-1004 40A ESC
ASSEMBLY:
Install the propeller.
1 2 3 4 5 6 7
8
9 10
11 12 13
15 16 17 18 19 20
14
Install the landing gear cover with Double-sided tape.
1617
1617
Skytr-15 Decal
DY-1007 9g Servo
DYR-2001 2.4G Receiver DY-3003 Glue
SPARE PART LIST:
BM2815A-KV1100Brushless Motor
BM2815A-KV1100-ShaftMotor Shaft
DECAL:
Skytr-02 Wing Skytr-04 Elevator Skytr-03 Vertical Stabilizer
Skytr-09 Landing Gears
Skytr-07 Spinner
DY8938
Dynam RC
dynam-rc.cn
of
This product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Please recycle.
over
CENTER OF GRAVITY(C.G.)
DIRECTIONS FOR ASSEMBLY AND ADJUSTMENTWingspanLengthFlying WeightWing Area Wing LoadRadio SystemPowerBattery
: 1280mm (50.4in): 1000mm (39in): 1000g (35.3oz): 23dm² : 43.5g/dm²: 4 Ch TX and 7 Ch RX : Brushless System: LIPO, 2200 mAh, 11.1V
Control Throw Setting Suggestion
Elevator Aileron Rudder
11.1V 2200mAh Li-Po, 20C
(9060x3)
ESC-30A
ESC-40A
Lithium-polymer Battery
2200mAh 14.8V20C Discharge
Rechargeable CellsUse li-po charger only
MOTOR
DY-6006 11.1V 2200mAh20C Battery
DYAT-008 Servo Horn DY-3001 Quick-Controller
Skytr-01 Fuselage
Skytr-05 Wing Back Cowl Skytr-06 Cowl
Skytr-14 Bolt Pipe
Connect the pushrod on the rudder and secure the screw (the servo should be in the center position) .
Connect the pushrod on the elevator and secure thescrew (the servo should be in the center position) .
Connect the aileron servos with the Y wires.
Connect the direction pushrod.( The servo should be in center position)
55 60 55 60
11
8
92
5
12
3
61
134
157
10
16
17
Slide the nose gear into the slot on the bottom of the fuselage.
Use a hexagon screwdriver to tighten the screw.
Remove the tape from both sides of the fuselage head.
Install the cowl . Install the landing gear with PA2.5*8mm screws.
Install the horizontal stabilizer and vertical stabilizer.
Secure the stabilizers with PA2.3*20mm screw.
Install the spinner with PA2*6mm screws.
Apply glue on the antenna and insert it into the main wing as shown.
Apply glue on the contact area of the left and right wing.
Glue the left and right main wings together.
Secure the wing onto the fuselage with PA2.3*20mm screws.
Secure the wing struts with PA 2.5*8mm screws. Install the battery.
DYT-2002 4CH Transmitter
DY-3007 Flap hinges
Skytr-08 Plastic Part Set
Skytr-10 Canopy Skytr-11 Push Rod Skytr-12 Wing Struts
Skytr-13 Propeller Skytr-16 Plastic Tab
Skytr-17 Screw set
