Altivar 320 / Altivar 32 EMC filters Altivar 340 / Lexium 32 ......Altivar 320 / Altivar 32 Altivar...
Transcript of Altivar 320 / Altivar 32 EMC filters Altivar 340 / Lexium 32 ......Altivar 320 / Altivar 32 Altivar...
-
1/3
S1A4761505
Altivar 320 / Altivar 32Altivar 340 / Lexium 32
DANGER
VW3A4420 ... A4426
Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibilityis assumed by Schneider Electric for any consequences arising out of the use of this product.© 2016 Schneider Electric. All Rights Reserved.
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH• Only appropriately trained persons who are familiar with and understand the contents of this manual and all other
pertinent product documentation and who have received safety training to recognize and avoid hazards involved are authorized to work on and with this drive system. Installation, adjustment, repair, and maintenance must be performed by qualified personnel.
• The system integrator is responsible for compliance with all local and national electrical code requirements as well as all other applicable regulations with respect to grounding of all equipment.
• Many components of the product, including the printed circuit boards, operate with mains voltage. Do not touch. Use only electrically insulated tools.
• Do not touch unshielded components or terminals with voltage present.• Motors can generate voltage when the shaft is rotated. Prior to performing any type of work on the drive system, block
the motor shaft to prevent rotation.• AC voltage can couple voltage to unused conductors in the motor cable. Insulate both ends of unused conductors of
the motor cable.• Do not short across the DC bus terminals or the DC bus capacitors or the braking resistor terminals.• Before performing work on the drive system:
- Disconnect all power, including external control power that may be present.- Place a "Do Not Turn On" label on all power switches.- Lock all power switches in the open position.- Wait 15 minutes to allow the DC bus capacitors to discharge. The DC bus LED is not an indicator of the
absence of DC bus voltage that can exceed 800 Vdc.- Measure the voltage on the DC bus between the DC bus terminals (PA/+, PC/-) using a properly rated
voltmeter to verify that the voltage is
-
2/3S1A47615-05 www.schneider-electric.com
VW3A4420 72 2.82 195 7.63 37 1.45 52 2.04 180 7.05 4,5 0.18107 4.2 195 7.63 35 1.37 85 3.32 180 7.05 4,5 0.18
(mm)a b c G H Ø
(inch) (mm) (inch) (mm) (inch) (mm) (inch) (mm) (inch) (mm) (inch)
VW3A4421
ppp 32ppppM2(B)
L'1
L1
2 a
L'2
L2
U/T1 W/T3
M
S/L2R/L1
V/T2
VW3A4420 VW3A4421 VW3A4426
VW3A4420 9A ATV320U02M2B...U07M2B, ATV32H018M2...H075M2LXM32pU45M2, U90M2
LXM32pD18M2, D30M2VW3A4421 16A
VW3A4426 22A
c
b H b
4 x Ø
Ga
140 5.48 235 9.2 35 1.37 120 4.7 215 8.42 4,5 0.18VW3A4426
1,8 N.m15.9 lb.in
ATV320U11M2B...U15M2B, ATV32HU11M2...HU15M2
ATV320U22M2B, ATV32HU22M2
VW3A442p
... N.m(... lb.in)
?
-
S1A47615-05 www.schneider-electric.com3/3
VW3A442p
pppppppppN4p
L'1
L1
3 a
L'2
L2 L3
S/L2R/L1
U/T1 V/T2 V/T3
M
L'3
T/L3
VW3A4422 VW3A4423 VW3A4424 VW3A4425
107 4.2 195 7.63 42 1.65 85 3.32 180 7.05 4,5 0.18140 5.48 235 9.2 50 1.96 120 4.7 215 8.42 4,5 0.18
(mm)a b c G H Ø
(inch) (mm) (inch) (mm) (inch) (mm) (inch) (mm) (inch) (mm) (inch)VW3A4422 VW3A4423
180 7.05 305 11.94 60 2.35 140 5.48 285 11.15 5,5 0.22VW3A4424
LXM32pU60N4, D12N4, D18N4, D30N4
LXM32pD72N4
VW3A4422 15 AATV320U04N4B...U40N4B, ATV32H037N4...HU40N4
VW3A4423
VW3A4424
VW3A4425
25 A
47 A
49 A ATV320D11N4B, D15N4B, ATV32HD11N4, D15N4
ATV320U55N4B, U754B, ATV32HU55N4, HU75N4
245 9.59 395 15.46 60 2.35 205 8.03 375 14.7 5,5 0.22VW3A4425
A4424A4425
a
H
Ø G
c
b
A4422A4423
c
b H b
Ga
4 x Ø
1,8 N.m15.9 lb.in
... N.m(... lb.in)
?
LXM32pD84N4, C10N4
ATV340U07N4p …. ATV340U15N4p
ATV340U22N4p …. ATV340U75N4p
S1A-P01.pdfS1A-P02S1A-P03