8/10/2019 Alpine DVI 9900

1/12

English

Deutsch

Espaol

Italiano

Svenska

Franais

R

Guide for Installation and Connections

DVI-9990RDVD-Audio/Video Tuner

Hinweise ber die Installation und Anschlsse

Guide dinstallation et de connexions

Gua de instalacin y conexiones

Guida allinstallazione ed ai collegamenti

Vgledning fr montering och anslutningar

8/10/2019 Alpine DVI 9900

2/12

2-EN

GUIDE FOR INSTALLATION AND CONNECTIONS

Please read this GUIDE FOR INSTALLATION AND CONNECTIONS and the OWNERSMANUAL thoroughly to familiarize yourself with each control and function. We at ALPINE hope

that your new DVI-9990R will give you many years of listening enjoyment.In case of problems when installing your unit, please contact your authorized ALPINE dealer.

Points to Observe for Safe Usage

Read this manual carefully before starting operation and use this system safely. We cannot be

responsible for problems resulting from failure to observe the instructions in this manual. This manual uses various pictorial displays to show how to use this product safely and to avoid

harm to yourself and others and damage to your property.

Here is what these pictorial displays mean. Understanding them is important for reading this

manual.

Meaning of displays

DO NOT DISASSEMBLE OR ALTER.Doing so may result in an accident, fire or electric shock.

USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES.Failure to do so may

result in fire or electric shock.

MAKE THE CORRECT CONNECTIONS.Failure to make the proper connections may result in

fire or product damage.

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.(Check with your dealer if you are

not sure.) Failure to do so may result in fire, etc.

BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL.

Failure to do so may result in electric shock or injury due to electrical shorts.

DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS.Arrange

wiring and cables in compliance with the manual to prevent obstructions when driving. Cables or

wiring that obstruct or hang up on places such as the steering wheel, shift lever, brake pedals,etc. can be extremely hazardous.

DO NOT SPLICE INTO ELECTRICAL CABLES.Never cut away cable insulation to supply power

to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fireor electric shock.

This symbol means important instructions. Failure to heed them can

result in serious injury or death.

This symbol means important instructions. Failure to heed them can

result in injury or property damage.

Warning

Caution

Warning

PRECAUTIONS

8/10/2019 Alpine DVI 9900

3/12

3-EN

DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.When drilling holes in the

chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuellines, tanks or electrical wiring. Failure to take such precautions may result in fire.

DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE

GROUND CONNECTIONS.Bolts or nuts used for the brake or steering systems (or any other

safety-related system), or tanks should NEVER be used for installations or ground connections.Using such parts could disable control of the vehicle and cause fire etc.

DO NOT BLOCK VENTS OR RADIATOR PANELS.Doing so may cause heat to build up inside

and may result in fire.

KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN.Swal-

lowing them may result in serious injury. If swallowed, consult a physician immediately.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS

THE STEERING WHEEL OR SHIFTLEVER.Doing so may obstruct forward vision or hamper

movement etc. and results in serious accident.

Caution

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.The wiring and installation of

this unit requires special technical skill and experience. To ensure safety, always contact thedealer where you purchased this product to have the work done.

USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY.Be sure to use only

the specified accessory parts. Use of other than designated parts may damage this unit internally

or may not securely install the unit in place. This may cause parts to become loose resulting inhazards or product failure.

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE.Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed

edges. This will prevent crimping and damage to the wiring. If wiring passes through a hole in

metal, use a rubber grommet to prevent the wires insulation from being cut by the metal edge of

the hole.

DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST.Avoid installing the unit

in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit

may result in product failure.

Precautions Be sure to disconnect the cable from the () battery post before installing your DVI-9990R. This

will reduce any chance of damage to the unit in case of a short-circuit.

Be sure to connect the color coded leads according to the diagram. Incorrect connections may

cause the unit to malfunction or damage to the vehicles electrical system. When making connections to the vehicles electrical system, be aware of the factory installed

components (e.g. on-board computer). Do not tap into these leads to provide power for this

unit. When connecting the DVI-9990R to the fuse box, make sure the fuse for the intended

circuit of the DVI-9990R has the appropriate amperage. Failure to do so may result in damage

to the unit and/or the vehicle. When in doubt, consult your ALPINE dealer. The DVI-9990R uses female RCA-type jacks for connection to other units (e.g. amplifier)

having RCA connectors. You may need an adaptor to connect other units. If so, please contact

your authorized ALPINE dealer for assistance.

8/10/2019 Alpine DVI 9900

4/12

4-EN

Contents

PRECAUTIONS 2

Accessories 5

Installation 6Connections 9

Connections with other equipments 10

To prevent external noise from entering the audio system.

Locate the unit and route the leads at least 10 cm away from the car harness.

Keep the battery power leads as far away from other leads as possible. Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if

necessary) of the car chassis.

If you add an optional noise suppressor, connect it as far away from the unit as possible.Your Alpine dealer carries various noise suppressors. Contact them for further information.

Your Alpine dealer knows best about noise prevention measures so consult your dealer for

further information.

IMPORTANTPlease note the serial number of your unit in the space provided below and keep it as a perma-

nent record. The serial number plate is located on the bottom of the unit.

SERIAL NUMBER:

INSTALLATION DATE:INSTALLATION TECHNICIAN:

PLACE OF PURCHASE:

To use this unit, a Multimedia Manager (PXI-H990, sold separately) or DAC unit (DAI-C990,

sold separately) is required. This unit is powered by connecting with the PXI-H990 or DAI-

C990.

8/10/2019 Alpine DVI 9900

5/12

5-EN

Power cable Flat screw

(M5 x 6)

x 4

Accessories

RCA Extension

cable (video)

S video cable

Remote control Battery (AAA) Reinforcement screw

(M3 x 12)

Remote control holder

Parts for remote control

Double-sided

adhesive tape

x 2

Front frame

Rubber Cap

Hex Bolt ISO Antenna

Convertor plug

8/10/2019 Alpine DVI 9900

6/12

6-EN

Remove the Detachable Front Panel (refer to page 9 of Owners Manual). Remove the front

frame from main unit (see Removalon page 7).

Slide the mounting sleeve into the dashboard.

When your vehicle has the bracket, mount the long hex bolt onto the rear panel of the DVI-

9990R and put the rubber cap on the hex bolt. If your vehicle does not have the mounting

support, reinforce the monitor unit with the metal mounting strap (not supplied). Connect the

ground lead of the unit to a clean metal spot using a screw () already attached to the

vehicles chassis.

For the screw marked , use an appropriate screw for the chosen mounting location.

Connect each input lead coming from the product you are connecting with to the correspond-

ing output lead coming from the left rear of the DVI-9990R. Connect all other leads of the DVI-9990R according to details described in the Connectionssection.

Installation

1

2

Installation Location

Before deciding on the mounting location, check that opening and closing the display will not

hamper gear shifting in that position.

Install at an angle of within 35 degrees from the horizontal.

Mounting Sleeve

(Included)

Dashboard

Rubber Cap (Included)

Hex Bolt (Included)

DVI-9990R

Bracket

Hex Nut (M5)Screw

Bolt Stud

Metal Mounting

Strap

DVI-9990RGround Lead

Chassis

8/10/2019 Alpine DVI 9900

7/12

7-EN

3Slide the DVI-9990R into the dashboard. When the unit is in place, make sure the locking pins

are fully seated in the down position. This can be done by pressing firmly in on the unit while

pushing the locking pin down with a small screwdriver. This ensures that the unit is properly

locked and will not accidentally come out from the dashboard. Install the Detachable FrontPanel.

Removal

1 Remove the DETACHABLE FRONT PANEL.

2 Use a small screwdriver (or similar tool) to push the locking pins to the upposition (see abovedrawing). As each pin is unlocked, gently pull out on the unit to make sure it does not re-lock

before unlocking the second pin.

3 Pull the unit out, keeping it unlocked as you do so.

< JAPANESE CAR >

NOTEConnect the ground lead of the unit to a clean metal spot using a screw () already attached to the vehicle's chassis.

Lock pin

Front Frame

DVI-9990R

Ground Lead Screws (M5 x 6)

(Included)

Mounting Bracket

8/10/2019 Alpine DVI 9900

8/12

8-EN

Protective paper

Remote Control

Remote Control

Holder

Console Box etc.

Reinforcement Screws

Mounting the remote control holder

If the remote control is in direct sunlight, remove it from the holder and keep it in the glove

box.

When the holder cannot be mounted securely with Velcro tape, mount it by using screws.

8/10/2019 Alpine DVI 9900

9/12

9-EN

Video output connectorOutputs a video signal.Connects to the video input of the TV monitor you are linking with. There is a copy protect signal included in the video output signal, so that recording

with a VCR (Video Cassette Recorder) etc., is not possible.Also, depending on the monitor, the picture may not be displayed correctly.

IONBUS terminalConnects with IONBUS compatible products.

S video output terminal

Outputs a video signal.Connects with ALPINE products with a S video input terminal.

DVD Audio Link terminalConnects with the DVD Audio Link terminal of the PXI-H990 Multimedia Manager orDAI-C990 DAC unit.(Connect when using a DVD audio disc. Remove the terminal cover and plug in theDVD Audio Link cable).

Connections

Basic Connection

NOTES

Do not install the power supply unit where it will be exposed to moisture such as under the floor mat or near the air

conditioner. This may cause a malfunction.

Do not bundle the power supply unit cable with the audio cables. Noise may be induced into your system. The power supply unit temperature can become hot. This is not a malfunction.

Antenna Receptacle

Power Antenna LeadConnect this lead to the +B terminal of your power antenna, if applicable.

Illumination LeadThis lead may be connected to the vehicles instrument cluster illumination lead.This will allow the backlighting of the DVI-9990R to dim whenever the vehicleslights are turned on.

Ground LeadConnect this lead to a good chassis ground on the vehicle. Make sure theconnection is made to bare metal and is securely fastened using the sheet metalscrew provided.

Switched Power Lead (Ignition)Connect this lead to an open terminal on the vehicles fuse box or another unusedpower source which provides (+)12V only when the ignition is turned on or in theaccessory position.

Battery LeadConnect this lead to the positive (+) post of the vehicles battery.

Blue

Orange

Black

Red

Yellow

Fuse(7.5A)

Color Cable Cable Specifications

Yellow

Power supply unit

8/10/2019 Alpine DVI 9900

10/12

10-EN

Connections with other equipments

System Connection

NOTES

Do not install the power supply unit where it will be exposed to moisture such as under the floor mat or near the airconditioner. This may cause a malfunction.

Do not bundle the power supply unit cable with the audio cables. Noise may be induced into your system.

The power supply unit temperature can become hot. This is not a malfunction.

* For the Ferrite Core, refer to the Owners Manual of the product that the IONBUS cable is attached to.

*

*

*

*

*

*

Antenna ReceptacleTo antenna plug of the vehicle

To power antenna

To the instrument cluster illumination lead

Connect to a metal part of chassis body with a screw.

Ignition Key

Fuse (7.5A)

Battery

Blue

Orange

Black

Red

Yellow

IONBUScompatible

monitor(TMI-M990)

(sold separately)

IONBUScompatiblemonitor box

System switch1 (SYSTEM)

selected

DVD Audio Link cable(Included with the PXI-H990 or DAI-C990)

IONBUS cable(Included with theTMI-M990)

Multimedia ManagerPXI-H990

orDAC unitDAI-C990

(sold separately)

IONBUS cable(Included with the KCI-500B)

IONBUS

cable

S

vid

eocable(Included)

Ai-NET/IONBUSconverter

(KCI-500B)(sold separately)

CD changer(Ai-NET)

orDAB

Receiver Box

(soldseparately)

When connecting the changer orDAB Receiver Box, you mustuse an Ai-NET/IONBUS converter(KCI-500B).

Connectable system productsIONBUS compatible monitorMultimedia Manager or DAC unit

Ai-NET/IONBUS converterAi-NET compatible changer

DAB Receiver Box

TMI-M990PXI-H990 or DAI-C990

KCI-500BCHA-S634 or CHA-1214

TUA-T100DAB

Power supply unit

Ai-NET cable(Included with CD changer or DAB Receiver Box)

POWER ANT

ILLUMINATION

GND

IGNITION

BATTERY

ToIONBUS terminal

To DVD Audio Linkterminal

ToIONBUSterminal To IONBUS

terminal

ToIONBUSterminal To Ai-NET

connector

System switch (PXI-H990 only) Set to SINGLE when

connecting one PXI-H990.

When connecting two PXI-H990s, set the first to FRONT,and the secondto REAR.

8/10/2019 Alpine DVI 9900

11/12

11-EN

System Connection

NOTES

Do not install the power supply unit where it will be exposed to moisture such as under the floor mat or near the airconditioner. This may cause a malfunction.

Do not bundle the power supply unit cable with the audio cables. Noise may be induced into your system.

The power supply unit temperature can become hot. This is not a malfunction.

* For the Ferrite Core, refer to the Owner s Manual of the product that the IONBUS cable is attached to.

*

*

Power supply unit

Antenna ReceptacleTo antenna plug of the vehicle

To power antenna

To the instrument cluster illumination lead

Connect to a metal part of chassis body with a screw.

Ignition Key

Blue

Orange

Black

Red

Yellow

Fuse (7.5A)

Battery

Video output connector

IONBUS cable(Included with the PXI-H990 or DAI-C990)

DVD Audio Link cable(Included with the PXI-H990 or DAI-C990) Multimedia Manager

PXI-H990or

DAC unitDAI-C990

(sold separately)

External TVmonitor

(sold separately)

Connectable system productsMultimedia Manager or DAC unit

External TV monitor

PXI-H990 or DAI-C990

IONBUS incompatibleTV monitor

Yellow

RCA Extension cable (video)(Included)

POWER ANT

ILLUMINATION

GND

IGNITION

BATTERY

To DVD Audio Linkterminal

To IONBUSterminal

System switch (PXI-H990 only) Set to SINGLE when

connecting one PXI-H990.

When connecting two PXI-H990s, set the first to FRONT,and the secondto REAR.

8/10/2019 Alpine DVI 9900

12/12

Sankei Kikaku Co., Ltd.

1-13-38, Hinodai,

Hino, Tokyo, Japan

ALPINE ELECTRONICS MARKETING, INC.

1-1-8 Nishi Gotanda,Shinagawa-ku, Tokyo 141-0031, Japan

Phone 03-5496-8231ALPINE ELECTRONICS OF AMERICA, INC.

19145 Gramercy Place, Torrance,California 90501, U.S.A.

Phone 1-800-ALPINE-1 (1-800-257-4631)

ALPINE ELECTRONICS OF CANADA, INC.

7300 Warden Ave., Suite 203, Markham,Ontario L3R 9Z6, Canada

Phone 1-800-ALPINE-1 (1-800-257-4631)

ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD.

6-8 Fiveways Boulevarde Keysborough,Victoria 3173, AustraliaPhone 03-9769-0000

ALPINE ELECTRONICS GMBH

Frankfurter Ring 117, 80807 Mnchen,Germany

Phone 089-32 42 640

ALPINE ELECTRONICS OF U.K. LTD.

Alpine House

Fletchamstead Highway,Coventry CV4 9TW, U.K.Phone 0870-33 33 763

ALPINE ELECTRONICS FRANCE S.A.R.L.

(RCS PONTOISE B 338 101 280)98, Rue de la Belle Etoile, Z.I. ParisNord II, B.P. 50016, 95945 RoissyCharles de Gaulle Cedex, France

Phone 01-48638989

ALPINE ITALIA S.P.A.

Viale C. Colombo 8, 20090 TrezzanoSul Naviglio (MI), Italy

Phone 02-484781

ALPINE ELECTRONICS DE ESPAA, S.A.Portal de Gamarra 36, Pabelln, 32

01013 Vitoria (Alava) - APDO 133, SpainPhone 945-283588

Designed by ALPINE Japan

Printed in Japan (S)68-00323Z08-A

R