Alabama Home Builders Self Insurers Fund
description
Transcript of Alabama Home Builders Self Insurers Fund
Alabama Home Builders Self Insurers Fund
Skid Steer Operator Training Program
Presented by the AHBSIF Loss Control Department
Course Outline
I. IntroductionII. General Safety PrecautionsIII. Safe Operating ProceduresIV. Emergency SituationsV. Driving Test
I. Introduction
IntroductionThis presentation will provide
participants with the following:
General descriptionGeneral safety precautionsSafe operating proceduresEmergency Situations
Components of a Skid Steer
Lift Arm
Roll Over Protection System (ROPS)
Hydraulic Block
Bucket Attachment
Safe Entry Aids, Grab Rail and Non-Slip
Step
Warning Lights
All-Wheel Steer
Common Safety DevicesRoll Over Protection System
Overhead ProtectionSeatbeltProtective cage
Pedestrian Warning DevicesLightsHorn
Operator’s Manual
Attachments
II. General Safety Precautions
Signage Alerts
operators to special messages regarding:
OperationMaintenanceSafety
Precautions
Recognition of emphasized messages:
NOTE• This message is used when special information, instructions, or identification
is required relating to procedures, equipment, tools, pressures, capacities, and other special data.
IMPORTANT• This message is used when special precautions should be taken to ensure a
correct action or to avoid damage to, or malfunction of, the truck or a component.
CAUTION• This message is for proper precautions which, if not followed, can result in
personal injury. WARNING
• This message is used when a hazard exists which can result in injury or death if proper precautions are not taken.
DANGER• This message is used when an extreme hazard exists which will result in
death or serious injury if proper precautions are not taken immediately.
Benefits of Operator Training It improves safety for the operator and others It Improves morale
Increased employee responsibility The operator learns how to perform a pre-shift inspection
Reduce down time Increase productivity Reduce maintenance costs Improve safety
The equipment is better cared for Employees understand the value of the equipment and how to
use it efficiently Operator training and progress is documented OSHA requirements are fulfilled
Operate only if qualified Do not operate unless you have been trained to
do so and are familiar with the operator's manual Familiarize yourself with the job site and your
surroundings before operating. Try all controls and machine functions with the
machine in an open area before starting to work. Know and observe all jobsite specific safety
rules
Protective Equipment Safety Glasses and Face Shield
Guard against injury from flying pieces of metal or debris; wear face shield or safety glasses.
Proper AttireWear close fitting clothing and safety equipment
appropriate to the job. Ear Plugs and/or Muffs
Wear suitable hearing protection to protect against loud or prolonged noises.
Always contact an authorized dealer before making machine modifications
Changes can effect the following:Intended use of skid steerWeight or balance of the machineCan alter machine controls, performance or
reliability
Machine Modifications
Pre-shift Inspection
Inspect machine carefully each day by walking around it before starting.
Keep all guards and shields in good condition and properly installed.
Fix damage and replace worn or broken parts immediately.
Pay special attention to hydraulic hoses and electrical wiring.
Stay Clear of Moving Parts Entanglements in moving parts can cause
serious injury. Maintenance procedures require the following
Engine offControls in neutralParking brake setPark on level surface, wheel chocks if needed Hydraulics blocked
If any guard or shield has been removed for access, replace when complete.
Potential Hazard Exposures High Pressure Oils
Most machines use a high-pressure hydraulic system. Escaping oil under pressure can penetrate the skin causing serious injury.
Hydraulic oil that penetrates the skin must be treated immediately.
Use the “cardboard test” to locate potential hydraulic fluid leaks.
Potential Hazard Exposures
Exhaust FumesEngine exhaust fumes can cause sickness or death. If you must operate in a building provide adequate
ventilation. Use an exhaust pipe extension to remove the exhaust
fumes.Open doors and windows to bring outside air into the
area.
Potential Hazard Exposures Battery Explosions
Battery gas can explode. Keep sparks, flames, and other ignition sources away from the top of the battery.
Never check battery charge by placing a metal object across the posts, use a voltmeter.
Never charge a frozen battery; it may explode. Warm battery to 16°C (60°F).
Potential Hazard Exposures Fire Prevention
Handle Fuel Safely: Store flammable fluids away from fire hazards. Never refuel machine while smoking or when near sparks or flame.
Clean Machine Regularly: Keep trash, debris, grease and oil from accumulating in engine compartment, around fuel lines, hydraulic lines and electrical wiring. Never store oily rags or flammable materials inside a machine compartment.
Maintain Hoses and Wiring: Replace hydraulic hoses immediately if they begin to leak, and clean up any oil spills. Examine electrical wiring and connectors frequently for damage.
ExtinguishersOrdinary Combustibles
Includes materials such as wood and paper
Flammable LiquidsIncludes fuels, grease, other liquids
Electrical FiresContains non-conductive smothering
agent
How to Use a Fire ExtinguisherP-A-S-S
Pull -- Pull the pin at the top of the extinguisher that keeps the handle from being activated
Aim -- Aim the nozzle at the base of the fire
Squeeze -- Maintain a distance of eight to ten feet away from the fire and squeeze the handle. Discharge will only occur if the handle is being squeezed.
Sweep -- Sweep the nozzle back and forth at the base of the fire until it appears to be out.
Potential Hazard ExposuresChemical Hazard Communication
Exposure to hazardous chemicals can cause serious injury.
Lubricants, coolants, paints and adhesives used with this machine may be hazardous.
If uncertain about safe handling or use of these chemical products, contact your authorized dealer for a Material Safety Data Sheet (MSDS).
Waste Disposal Fuel, oils, coolants, filters and batteries used
with the machine may be harmful to the environment.
Never pour waste onto the ground, down a drain, or into any water source.
Material must be disposed of in accordance with the rules and regulations of federal and state agencies.
ADEM (Alabama Dept. of Environmental Management)Office of General Council; (334)-271-7977 (http://www.adem.state.al.us/)
Potential Spill ExposuresFuel dispensing areasMaintenance areasEquipment FailureImproper Storage vessels
DrumsBucketsUnapproved containers
III. Safe Operating Procedures
General Safety ProceduresFace the machine when getting on and
off, maintain 3-point contact at all times. Never use machine controls as
handholds. Use extra care in poor weather
conditions. Keep steps clean and free of grease or
oil.
General Safety ProceduresNever jump when exiting machine or exit
while the machine is moving. Start the engine only while sitting in
operator's seat.Always wear your safety belt. The complete seat belt assembly should
be replaced every three years, regardless of appearance.
General Safety Procedures
Be careful not to accidentally actuate controls when co-workers are present.
Lower all equipment to the ground during work interruptions. Engage park brake before allowing anyone to approach the machine.
Follow these same precautions before standing up, leaving the operator's seat, or exiting the machine.
Potential Site Hazards
Buried utilities, i.e. water, cable, electrical
Adjacent structures or objects that could fall onto the machine.
Poor housekeeping, excessive debris.Overhead power lines.
Potential Site HazardsAwareness of bystanders and fellow
workers. Use barricades or a signal person to keep
vehicles and pedestrians away. Travel path conditions.
Steep terrainSoft soil Loose gravelRuttingUneven transitions
Operator Fundamentals
Keep Riders Off the MachineOnly allow operator on machine. Riders are subject to injury. They may fall from
machine, be caught between machine parts, or struck by foreign objects.
Riders may obstruct operator's view or impair his ability to operate machine safely.
Operator FundamentalsAvoid Back-over Accidents
Before moving machine, be sure all persons or vehicles are clear of machine path.
Be certain reverse warning alarm is working properly.
Use a signal person when backing if view is obstructed or when in close quarters.
Operator Fundamentals Avoid Machine Tip Over
Use seat belt at all times. Never jump from a tipping machine. You will be
unlikely to jump clear and the machine may crush you.
Load and unload from trucks or trailers carefully. Be sure truck is wide enough and on a firm level surface. Use loading ramps and attach them properly to truck bed.
Operator FundamentalsAvoid Machine Tip Over
Use caution on slopes and avoid sharp turns. Balance loads so weight is evenly distributed
and load is stable. Carry tools and loads close to the ground to
aid visibility and lower center of gravity. Avoid overloading, know your machines
capacity.
Operator Fundamentals Operating or Traveling On Public Roads
For work near vehicle traffic you must have proper lighting and markings to assure visibility.
Additional lights, beacons, slow moving vehicle (SMV) emblems, or other devices may require installation.
Check state and local regulations to assure compliance. Keep these devices clean and in working condition.
Operator Fundamentals
Attachment Hook-Up and OperationAttachments must be compatible. Installation must handled by a competent
person.Verify that all connections are secure and
attachment responds properly to controls. Carefully read attachment manual and follow
all instructions and warnings. Test the attachment in an open area to insure
proper operation.
Refueling Gasoline and Diesel
The difference between these two fuels is their ignition temperatures.
GasolineExtremely flammableColorlessDistinctive odor
DieselHas higher ignition point than gasColorlessSlight odor, harder to detect than gas
RefuelingMost skid steer filler caps are equipped
with a venting device and a fuel screen.The screen serves as a fire retardant
device by keeping fire out of the fuel tank.Check when refueling to make sure the
screen is in place.
RefuelingSafe refueling checklist:
Refuel in designated areas with good ventilation
Smoking and open flames are prohibitedShut off the skid steer, lower the attachment,
controls in neutral, and set the parking brake before beginning
Don’t overfill the tankClean up any spillsUse only clean, properly marked fuel cans
BatteriesA lead-acid battery is a portable power
source for supplying direct current electricity.
The most common voltages include 12, 24, 36, and 48 volts.
Discharging a battery below 80% of its total capacity can result in shortened battery and truck component life.
Battery Hazards Sulfuric Acid – Small amounts can cause severe
contact burns to the skin. Gasses – Batteries produce hydrogen and
oxygen mixture continuously. Keep all ignition sources away.
Electricity – Batteries are capable of producing very high discharge rates. Avoid direct shorting situations.
Battery Weight – Use care when handling, charging, and using batteries in the truck.
IV. Emergency Situations
Are you prepared?Does the facility/jobsite have an
evacuation procedure?Are emergency contact numbers readily
available?Do any of your employees/co-workers
have CPR or First Aid training?Does the facility/jobsite have a first aid kit?
Handling an EmergencyThe three C’s, Check, Call, Care help us
remember what to do in an emergency situation.
Check – check the area for your own safety first, then the victim's
Call – for help, 911 or whom ever is in the immediate area that can provide assistance
Care - administer care to the victim, this may be first aid or at least stabilization
V. Driving Test
Pre-operation InspectionFamiliarization with
operating controlsDriver’s Test