Rev0411

Service and Support: 866-869-3114

Pt# 1312100695

Air CompressorManual

Models: 824254PGT824254PGTH82808PGT82808PGTH

82356VAT82358VAT82368VAT

82823GT82823GTH821023GT821023GTH821330GTK

TABLE OF CONTENTS

PAGE

1 Safety Guidelines - Definitions

Before Using the Air Compressor

2 When Installing or Moving the Compressor

Before Each Use

3 Follow Safety Precautions for Electrical Connection

Plan Ahead to Protect Your Eyes, Hands, Face & Ears

When Operating 4 Spraying Precautions

Perform These Maintenance Operations

5 Typical Compressor Installation

Glossary

6 Wiring

Starting the Compressor (Electric Compressors)

7 Starting the Compressor (Gasoline)

8 Troubleshooting Guide

9 Troubleshooting (Cont.)

10-18 Parts

Warranty Statement

WARNING

Safety is a combination of common sense, staying alert and knowing how your compressor works.Read this manual to understand this compressor.

CAUTION

DANGER

SAFETY GUIDELINES - DEFINITIONS

means if safety information is not followed someone will be seriously injured or killed

means if safety information is not followed someone may be seriously injured or killed

means if safety information is not followed someone could be seriously injured or killed

IMPORTANT SAFETY INSTRUCTIONS

Save these instructions

Before using the air compressor

Improper operation or maintenance of this product could result in serious injury and propertydamage. Read and understand all warnings and operation instructions before using this compressor.

Air compressors are utilized in a variety of airsystem applications. Because air compressorsand other components (hoses, connectors, air tools, spray guns, etc.) make up a high pressurepumping system, the following safety pre-cautions should be observed at all times.

Only persons familiar with these rules ofsafe operation should use the air compressor.

1. Read the instruction manual carefully before attempting to assemble, disassemble or operate your system. Be thoroughly familiar with the controls and the proper use of the equipment.

2. Review and understand all safety instructions and operating procedures in this manual.

3. Review the maintenance methods for this compressor (See “Maintaining Your Compressor” section).

Things you should know Inspect your work area

1. Keep work area clean.

2. Cluttered areas and benches invite accidents. Floors must not be slippery from wax or dust.

1. To reduce the risk of injury from accidental starting, turn switch off and disconnect the power before checking it.

2. If any part is missing, bent or broken in any way, or any electrical part does not work prop- erly, keep the compressor off and disconnected.

3. Check hoses for weak or worn condition before each use, making certain all connections are secure. Do Not use if defect is found.

Do not operate compressor if damaged duringshipping, handling or use. Damage may resultin bursting and cause injury or property damage.

This compressor is Not designed for and shouldnot be used in breathing air applications.

Inspect your compressor

WARNING

Page 1

DANGER

When installing or moving the compressor

This compressor is extremely top heavy. Thecompressor must be secured to the floor before operating to prevent equipment damage, injury or death. The compressor mustbe mounted on vibration pads. Do Not tighten bolts completely as this may cause stress to the tank welds.To reduce the risk of a dangerousenvironment

1. Keep work area well lit.

2. Operate compressor in a well-ventilated area free from flammable liquids and vapors.

3. Operate compressor in a ventilated area so that compressor may be properly cooled and the surrounding air temperature will not be more than 100°F.

4. Never use a compressor in a wet environment.

5. Protect material lines and air lines from damage or puncture. Keep hose and wires away from sharp objects, chemical spills, oil, solvents and wet floors.

Do Not secure compressor with toggle boltsinto drywall. Drywall sheeting or plaster will notsupport the weight of the compressor.

WARNING

Page 2

6. A minimum clearance of 18 inches between the compressor and a wall is required because objects could obstruct airflow.

7. The compressor should be located where it can be directly wired to a circuit breaker. The compressor should be wired by a qualified electrician.

8. Never store flammable liquids or gases in the vicinity of an operating compressor.

9. Do Not locate the compressor air inlet near steam, paint spray, sandblasting areas or any other source of contamination. The debris could damage the motor and pump.

Never use plastic (PVC) pipe for compressedair. Serious injury or death could result.

Never use the shipping skid for mounting thecompressor.

This compressor is not intended for outdoorinstallation.

Never install a shut off valve between the compres-sor pump and tank. Personal injury and/or equipment damage could occur.

WARNING

CAUTION

NOTICE

WARNING

WARNING

Before each use

1. Keep work area clean. Cluttered areas and benches invite accidents.

2. The floor must not be slippery from wax or dust.

1. To reduce the risk of injury from accidental starting, turn the switch off and disconnect power.

2. If any part is missing, bent or broken in any way, or any electrical part does not work properly, keep the compressor off and dis- connect power. Do Not use if defect is found.

3. Check hoses for weak or worn condition before each use, making certain all connect- ions are secure. Do Not use if a defect is found.

Inspect your work area Inspect your compressor

Note: Tank Outlet Size: Contractor Models 3/8” 60 Gallon Models 1/2” 80 Gallon Models 3/4”

Follow the safety precautions for electrical connections

Page 3

WARNING

CAUTION

WARNING

Plan ahead to protect your eyes, hands, face and ears

1. Wear safety glasses (meeting ANSI Z87.1 or in Canada CSA Z94.3-99) and use hearing protection when operating the unit. Everyday glasses are not safety glasses.

2. Wear shoes to prevent shock hazards.

3. Tie back long hair.

Keep fingers away from running compressor.Fast moving and hot parts may cause injuryand/or burns.

1. Follow all local electrical and safety codes, as well as the National Electric Code (NEC) and the Occupational Safety and Health Act (OSHA).

2. Wiring and fuses should follow electrical codes, current capacity and be properly grounded.

3. Protect wires from contact with sharp objects.

All electrical connections should be made bya qualified electrician.

Dress for safety

Be careful when touching the exterior of comp-ressor, pump, motor and air lines; they may become hot enough to cause injury.

Never operate the compressor without a beltguard. The compressor can start auto-matically without warning. Personal injury or property damage could occur from contact with moving parts.

The compressor may be hot even if the unit is stopped.

Use of a mask or respirator per chemical manufacturers’ instructions may be neces-sary if there is a chance of inhaling toxic fumes.Read mask and respirator instructions care-fully. Consult a safety expert if you are notsure about the use of certain masks or respirators.

Pay attention to your hands

WARNING

CAUTION

WARNING

When operating

1. Do not exceed the pressure rating of any component of the system.

2. Release pressure within the system slowly to prevent flying dust and debris.

3. If the equipment starts to abnormally vibrate, STOP the compressor immediately and check for the cause.

WARNING

Never change the safety valve or pressure switch settings. Keep safety valve free from paint and other accumulations. See compressorspecification decal for maximum operatingpressure. Do not operate with the pressureswitch set higher than the maximum operatingpressure.

Spraying precautions

Page 4

Perform these maintenance operations

1. Do Not spray in the vicinity of open flames or other places where a spark can cause ignition. Do Not smoke when spraying paint, insecticides, or other flammable substances.

1. When spraying with solvents or toxic chemi- cals, follow the instructions provided by the chemical manufacturer. Consult a safety expert if unsure about the use of masks or respirators.

2. If the material you intend to spray contains trichloreoethane and methylene chloride, do not use accessories that contain aluminum or galvanized materials, as these chemicals can react with galvanized components causing corrosion and weakening equipment. Use stainless steel accessories.

WARNING

Never point a spray gun at yourself or anyother person or animal. Accidental dischargemay result in serious injury.

Reduce the risk of dangerousenvironment

WARNING

Extreme caution should be taken whenspraying flammable liquids as the spark froma motor or pressure switch may cause a fireor explosion. Ample ventilation must beprovided.

WARNING

Spray in a well ventilated area to keep fumesfrom collecting and causing serious injury andfire hazards.

Be informed about the materials you use

1. Do regular maintenance; keep all nuts, bolts, and screws tight, to be sure equipment is in safe working condition.

2. Inspect tank yearly for rust, pin holes or any other imperfections that could cause it to become unsafe.

NEVER attempt to repair or modify a tank!Welding, drilling or any other modification willweaken the tank resulting in damage from rupture or explosion. Always replace worn,cracked or damaged tanks.

3. Clean electrical equipment with an approved cleaning agent, such as a dry, non-flam- mable cleaning solvent.

Daily

Check oil level at sight glass. Oil level shouldbe 1/2 to slightly higher in the oil sight glass.

Drain moisture from tank.

Verify the pressure switch unloader isworking by listening for a brief hissing soundwhen the compressor shuts off.

Visually check the compressor for loose parts,excessive noise or vibration. Tighten anynecessary part.

WARNING

4. Drain tanks of moisture after each day’s use. If unit will not be used for awhile, it is best to leave the drain cock open until such time as it is to be used. This will allow moisture to completely drain out and help prevent corrosion of inside of tank.

5. Always disconnect from power source before working on or near a motor, or its connected load. If power disconnect point is out-of- sight, secure it in the “OFF” position and tag it to prevent unexpected application of power.

Disconnect power and depressurize systembefore servicing air compressor. Slightly opendrain cock after shutting off compressor.

Monthly(Make sure the main power is off.) Check the beltsfor tension. Belts should not move up and downwhen the compressor runs and when stopped,should not have more than ½ in of play whendepressed. Be careful not to over tighten beltsduring adjustment.

Remove and check air filter, replace if necessary.

Change oil every 3 months or 300 hours. A compressor grade non-detergent oil should beused Part # 82-6020.

WARNING

Page 5

WIRINGTYPICAL COMPRESSOR INSTALLATION

GLOSSARY OF TERMS

Air Filter

Porous element contained within a metal orplastic housing attached to the compressorcylinder head which removes impurity from theintake air of the compressor.

Air Tank

Cylindrical component which contains thecompressed air.

Check Valve

Device which prevents compressed air fromflowing back from the air tank to the compres-sor pump.

Electric Motor

Device which provides the rotational forcenecessary to operate the compressor pump.

Pressure Gauge

Device which shows the tank or regulatedpressure of the compressed air.

Pressure Switch

Device which automatically controls the on/offcycling of the compressor. It stops the compressor when the cut-off pressure inthe tank is reached and starts the compressorwhen the air pressure drops below the cut-inpressure.

PSI (Pounds per Square Inch)

Measurement of the pressure exerted by theforce of air. The actual psi is measured by apressure gauge on the compressor.

Pump

Device which produces the compressed airwith a reciprocating piston contained within acylinder.

Safety Valve

Device which prevents air pressure in the airtank from rising over a predetermined limit.

Thermal Overload Switch

Device, integrated into the electric motor winding,which automatically “shuts off” the compressorif the temperature of the electric motor exceedsa predetermined limit.

Flex Hose Air

Dryer

To Air System

Vibration Pads

Page 6

To reduce the risk of electrical hazards, firehazards or damage to the compressor, useproper circuit protection. Your compressoris wired at the factory for operation usingthe voltage shown. Connect the compressorto a power source with the correct breakersize.

Adequate wiring and motor protectionshould be provided for all stationarycompressors. Wiring used for othermachinery should not be used. Aqualified electrician familiar with localelectrical codes in your area should beused. Size supply wiring per NEC (NationalElectric Code) requirements.

WIRING

ALL ELECTRICAL WIRING SHOULD BE DONEBY A QUALIFIED ELECTRICIAN

General Information

STARTING THE COMPRESSORPrior to actually running the compressor,check the following items:

Crankcase oil - Make sure the sight glassshows ½ full or slightly above.

Make sure all rags, tools, oil, etc. are awayfrom the unit.

Open the air system to free it of any pressure.

Switch the compressor on for a fewrevolutions to make sure the rotation iscorrect. Correct rotation is clockwisewhen facing the sight glass on the pump.

Operate the compressor for a few minutesunloaded (air system open) then allow thecompressor to pump up. Make sure theelectrical pressure switch properly switchesoff the compressor according to the settingdesired. Note: Max Pressure Single Stage= 130 psi, 60 Gallon 2 Stage = 165 psi,80 Gallon 2 Stage = 175 psi

Make sure the pressure in the tank doesnot exceed its rating. Maximum of 175 psi. If the pressure gauge indicates a pressure thatis higher than these maximum pressures,shut off compressor immediately and call866-869-3114.

Electrical connections must be properlygrounded. Ground connections should beconnected at the grounding screw.

Overheating, short circuiting and fire damagewill result from inadequate wiring.

WARNING

WARNING

WARNING

CAUTION

WIRING

STARTING THE COMPRESSOR

CAUTION

For Models Without Magnetic StarterIncoming power should be connectedto the posts marked (LINE)

Do Not Make Connections OnPrewired Posts Marked (MOTOR)!

Electrical connections must be properlygrounded. Groundconnections should beconnected at agrounding screw.

For Models With Magnetic Starter

DO NOT MAKE CONNECTION AT PRESSURE SWITCH

Ground

Incoming power shouldbe connected to L1 andL2 at the Top of the Magnetic Starter.

Page 7

(Gas Drive Models)

PLEASE REFER TO YOUR ENGINE OPERATION MANUAL FOR PROPER STARTINGINSTRUCTIONS.

CONTRACTOR MODELS INCLUDE A MANUAL UNLOADER. AIR PRESSURE SHOULD BE RELIEVED PRIOR TO STARTING. OPEN PET COCK ON UNLOADER TO RELIEVE ANY AIR PRESSURE. (See Image Below)

NAPA GASOLINE DRIVEN COMPRESSORS (30 GALLON) ARE EQUIPPED WITH A COLD START VALVE FOR LOADLESS STARTS. THERE IS NO NEED TO MANUALLY UNLOAD AIR PRESSURE.

Open Valve to Relieve Head Pressure

Once Started, Close Valve

Note:Make sure to follow instructions carefully to avoid a short and possible damageto the starter solenoid and/or battery. 1. Connect the positive (+) terminal on the battery to the starter solenoid.2. Connect the negative (-) terminal on the battery to an engine mounting bolt or other acceptable ground connection.Always connect the positive(+) battery cable to the starter solenoid before connectingthe negative(-) battery cable.

NUMBER 2 WIRE OR LARGER IS REQUIRED

Battery Connection Instructions for Electric Start Engines

BATTERY (12 Volt)

(+)(-)

GROUND

Starter Solenoid

Page 8

! DANGER

Low discharge pressure 1. Reduce air demand or use a compressor with more air capacity.2. Listen for air leaks. Apply a soap solution to all fittings and connections. Bubbles will form at points of leakage. Tighten or replace fittings or connections.3. Clean or replace air filter.4. Replace necessary gaskets.5. Remove head and inspect for broken or misaligned valves. Replace valves, if necessary. Install a new head gasket each time head is removed

1. Tighten drive pulley or flywheel bolt.2. Check for proper oil level. Low or dirty oil may cause bearing damage.3. Replace connecting rod and/or connecting rod bearings.4. Replace check valve. with air pressure in tank

1. Replace with new piston rings.2. Clean or replace air filter.3. Drain oil to proper oil level.4. Use a quality non-detergent 30 or 40wt oil specified for each model (Page 4).

1. Drain tank at least once per day.2. Add an inline filter to reduce moisture in in the air line.

1. Check voltage with volt meter across both legs of incoming power. Check reset button on motor.2. Repair or replace pressure switch.3. Replace check valve or pressure switch. Do not remove check valve with air pressure in tank

1. Make sure the breaker is sized properly. See page 6 in this manual.2. Check voltage with volt meter across both legs of incoming power.3. Replace motor.4. Check all electrical connections.5. Adjust or replace pressure switch.6. Replace check valve. Do not remove check valve with air pressure in tank

1. Replace check valve. Do not remove check valve with air pressure in tank2. Tighten or replace fittings or connections.3. Replace tank. Do not attempt to repair tank.

Do not remove check valve

1. Compressor too small for application

2. Air leaks

3. Restricted intake air4. Blown gasket(s)5. Broken or misaligned valves

! DANGER

! DANGER

! DANGER

1. Loose drive pulley or flywheel2. Low on oil

3. Worn connecting rod or connecting rod bearing4. Noisy check valve

1. Worn piston rings2. Restricted intake air3. Too much oil in compressor4. Incorrect oil viscosity

1. Normal. Amount of water will increase as humidity in the air increases.

1. Low voltage

2. Malfunctioning pressure switch3. Malfunctioning check valve

1. Incorrect breaker size

2. Low voltage

3. Malfunctioning motor4. Loose electrical connections5. Malfunctioning pressure switch6. Malfunctioning check valve

Tank does not hold pressure when notrunning and shut off valve is closed

Breaker or reset repeatedly trips

Will not run or motor hums

Water in tank and/or discharge line

Excessive oil carryover

Excessive noise “knocking”

TROUBLESHOOTING GUIDE

1. Malfunctioning check valve

2. Loose fittings or connections3. Crack or pin hole in tank

CAUTION!

Page 9

1. Replace pressure switch if it does not release air pressure briefly when unit shuts off. Do not remove pressure switch with air pressure in tank

1. Make sure unit is mounted on a level surface with vibration pads.2. Replace belts. Align and tighten properly.3. Align flywheel and drive pulley.

1. Reduce air demand or use a compressor with more air capacity.2. Clean all cooling surfaces of dirt and dust.3. Install compressor in an area with adequate cool dry air.

1. Malfunctioning check valve

Overheating

TROUBLESHOOTING GUIDE (Continued)

Pressure switch un-loader constantlyleaking air

1. Replace check valve if unloader bleeds constantly. Do not remove check valve with air pressure in tank! DANGER

Pressure switch not unloading

1. Malfunctioning pressure switch

! DANGER

Excessive vibration

1. Compressor too small for application2. Cooling surfaces dirty3. Improper cooling

1. Improper installation

2. Loose belts3. Misaligned flywheel or drive pulley

Twin Tank Compressors

1

9 7

65

4

3

28

11

1010

12

13

Page 10

Ill. No. Part Model Model Model ModelDescription 824254PGT 824254PGTH 82808PGT 82808PGTH

1 Compressor 821312100123 821312100123 824116090112 8241160901122 Engine 821312100728 821312100219 821312100729 8213121002213 Tank 821312201000 821312201000 821312201000 8213122010004 Idle Control 821312100382 821312100382 821312100740 8213121003825 Unloader/Pilot Valve 821312100496 821312100496 821312100496 8213121004966 Safety Valve 821312100005 821312100005 829710533300 8297105333007 Pres. Gauge 821312100378 821312100378 821312100378 8213121003788 Disch. Tube 821312100205 821312100205 821312100738 8213121007389 Wheel 821312100461 821312100461 821312100461 821312100461

10 Rubber Feet 821312100411 x 4 821312100411 x 4 821312100411 x 4 821312100411 x 411 Tank Drain 821312100360 821312100360 821312100360 82131210036012 Belt Guard Back 821312100147 821312100147 821312100147 821312100147

Belt Guard Front 821312100146 821312100146 821312100146 82131210014613 BG Fastener 821312100076 821312100076 821312100076 821312100076

Drive Pulley 821312100441 821312100441 821312100442 821312100441Drive Belt 821312100132 821312100132 821312100807 821312100132Ball Valve 821312100161 821312100161 821312100161 821312100161

Part Numbers Subject to Change without Notice

1010

1

9

76

5

4

3

2

12

11

1010

Page 11

Ill. No. Part Model Model ModelDescription 82356VAT 82358VAT 82368VAT

1 Compressor 824116090112 824116090112 8241160901582 Motor 821312100087 821312100087 8213121004003 Tank 821312100604 821312201100 8213122011004 Belt 821312100133 821312100137 821312100140 x 25 Press. Switch 821312100459 821312100554 8213121005706 Safety Valve 821312051870 829710533300 8297105333007 Press. Gauge 821312100028 821312100378 8213121000288 Mag. Starter NA NA 8213121006629 Tank Drain 821312100360 821312100360 821312100360

10 Disch. Tube 821312100214 821312100200 82131210020811 Inlet Filter 821312100376 821312100376 82131210037412 Belt Guard (Back) 821312100145 821312100148 821312100148

Belt Guard (Front) 821312100146 821312100150 821312100150Check Valve 821312100168 821312100170 821312100169

Belt Guard Clip 821312100076 821312100076 821312100076Unloader Line 821312100373 821312100373 821312100373Drive Pulley 821312100442 821312100442 821312100420

Part Numbers Subject to Change without Notice

Gas Drive Compressors

Page 12

Ill. No. Part Model Model Model Model ModelDescription 82823GT 82823GTH 821023GT 821023GTH 821330GTK

1 Compressor 824116090112 824116090112 824116090158 824116090158 8241160901582 Engine 821312100729 821312100222 821312100730 821312100223 8213121007073 Tank 821312201500 821312201500 821312201500 821312201500 8213122015004 Unloader Valve 821312100497 821312100497 821312100497 821312100497 8213121004975 Safety Valve 829710533300 829710533300 829710533300 829710533300 8297105333006 Press. Gauge 821312100378 821312100378 821312100378 821312100378 8213121003787 Disch. Tube 821312100744 821312100744 821312100209 821312100208 8213121002118 Ball Valve 821312100163 821312100163 821312100163 821312100163 8213121001639 Inlet Filter 821312100376 821312100376 821312100374 821312100374 821312100374

10 Tank Drain 821312100361 821312100361 821312100361 821312100361 82131210036111 Belt Guard (Back) 821312100149 821312100149 821312100149 821312100149 821312100149

Belt Guard (Front) 821312100150 821312100150 821312100150 821312100150 82131210015012 Belt 821312100138 821312100138 821312100139 x 2 821312100120 821312100141 x 213 Belt Guard Clip 821312100076 821312100076 821312100076 821312100076 82131210007614 Idle Control 821312100742 821312100382 821312100742 821312100382 821312100381

Drive Pulley 821312100442 821312100442 821312100735 821312100419 821312100421

Part Numbers Subject to Change without Notice

1

9

7

6

5

4

3

2

8

11

1010

14

13

Compressor Pump821312100123

Page 13

01 Valve Assembly Kit 02 Conrod Kit 03 Crankshaft Kit 04 Crankcase Bottom Kit 05 Cylinder Kit 06 Shaft Seal Kit 07 Head Kit 08 Flywheel Kit 09 Top Gasket Kit 10 Oil Level Kit 11 Air Filter Kit 12 Ring Kit (2 Required)

826229024900826229021800826229022800829428031826229023100829428050826229023900829428071826229023600829428100-KIT826229020500829428120

Compressor Pump821312100123

Page 14

02

01

03

04

06

05

07

13

15

10

08

12

14

11

09

18 2019

16

17

21

25

23

24

22

37

36

35

29

3940

30

34

38

27

28

33

26

32

31

44

45

49

45

48

47

46

50

Page 15

824116090112

41

Illustration Number Description Quantity Part No.

1. Crankcase 1 8249601002. Cylinder 1 8262229243003. Head 1 8262230186004. Crankshaft 1 8262128627005. Crankcase Bottom 1 8249613006. Valve Assembly 1 8262107172007. Conrod Insert (Half Bearing) 4 8262227259008. Conrod 2 8262226291009. Conrod Nut 4 82621434660010. HP Piston 1 82622272790011. LP Piston 1 82622272840012. HP Wrist Pin 1 82622272690013. LP Wrist Pin 1 82622272700014. Circlip 4 82621434200015. HP Compression Ring 1 82621286470016. HP Step Ring 1 82621286680017. HP Oil Ring 1 82621286580018. LP Compression Ring 1 82621286510019. LP Step Ring 1 82621286720020. LP Oil Ring 1 82621286630021. Aftercooler 1 82223610210222. Main Bearing Housing (NDS) 1 82622211240023. Bearing Housing (DS) 1 82622211270024. Intercooler Tube 1 82223610212725. Flywheel 1 82622401920026. Main Bearing (6205) 2 82621483320027. Oil Fill Plug 1 82621434180028. Oil Seal 1 82623163010029. Flywheel Bolt 1 82621184860030. Flywheel Washer 1 82621424280031. Crankcase Bottom Gasket 1 82623164580032. Frame Gasket 1 82623164520033. Cylinder Gasket 1 82623164650034. Valve Plate Gasket 1 82623164850035. Head Gasket 1 82623164900036. Bearing Housing Gasket 2 82623164540037. Aftercooler Gasket 1 82623164750038. Intercooler Gasket 2 82623164760039. Intercooler Safety Valve (1/4” 65 psi) 1 82621071660040. Oil Sight Glass 1 82223610299241. Air Filter Assembly 1

44. Head Bolt 6 82223610060845. Aftercooler/Intercooler/Inlet Bolt 8 829101254 46. Bearing Housing Bolt 8 82223610057847. Cylinder Bolt 6 82223610064448. Crankcase Bottom Bolt 8 82223610069349. Conrod Bolt 4 82223610063950. Oil Drain Tube 1 822236105583

KitsGasket Kit HP Ring Kit 822901323164HP Running Gear Kit 822901323150 LP Ring Kit 824924050

LP Running Gear Kit 828226505

828973035118

823095

Page 16

824116090112

4

2

8

3

9

5

6

20

7

1

19

18

17

16

15

14

13

11

12

10

34

33

32

31

3029

28

27

26

25

24

23

22

21

35

37

36

82411609015840

42

43

41

45

44

46

38

39

47

Page 17

4948

1. Crankcase 8260611002. Cylinder 8260300003. Head 8262230188004. Crankshaft 8262128629005. Crankcase Bottom 8262220176006. Crankcase Bottom Gasket 8262316451007. Valve Plate 8262107173008. Conrod Bearing (2 per Rod) 8262227260009. Connecting Rod 82622262930010. Conrod Nut 82621434660011. HP Piston 82622272820012. LP Piston 82622272770013. HP Wrist Pin 82622272730014. LP Wrist Pin 82622272850015. Circlip 82621434210016. HP Ring 82621286490017. HP Ring 82621286700018. HP Ring 82621286610019. LP Ring 82621286450020. LP Ring 82621286660021. LP Ring 82621286560022. Aftercooler 82624373150023. Bearing Housing (NDS) 82622211250024. Bearing Housing (DS) 82622211290025. Intercooler 82624373190026. Flywheel 82622401910027. Main Bearing 82621483480028. Main Bearing 82621483490029. Oil Sight Glass 82621434120030. Oil Fill Plug 82921434190031. Oil Seal 82623164490032. Flywheel Bolt 82621184850033 Flywheel Washer 82621424270034. Aftercooler Safety Valve 82SV2522535. Intercooler Safety Valve 82621071660036. Head Bolt 82223610060937. Cooler Bolt 82223610058938. Cylinder Bolt 82223610059639. Crankcase Btm. Bolt 82223610069040. Head Gasket 82223610933041. Cylinder Gasket 82223610932942. Aftercooler Gasket 82623164460043. Intercooler Gasket 82623164820044. Bearing Housing Gasket DS 82623164550045. Bearing Housing Gasket NDS 82623164570046. Frame Gasket 82623164660047. Oil Drain Tube 82223610558348. Filter Assembly 823257449. Filter Element 82-2580

Gasket Kit 828973035123

824116090158Ill. No. Description Part No.

Page 18

The Company warrants that the Equipment manufactured by it and delivered hereunder shall be free from defects in material and workmanship for a period of twelve (12) months from the date of initial start-up, or eighteen (18) months from the date of shipment from the manufacturer, whichever occurs first. The foregoing warranty period shall apply to all Equipment, except for the following: Replacement parts will be warranted for three (3) months from the date of shipment from the manufacturer. Should the failure to conform to this warranty be reported in writing to the Company within said period, the Company shall, at its option, correct such non - conformity by suitable repair to such Equipment, or furnish a replacement part F.O.B point of shipment, provided that the Purchaser has installed, maintained, and operated such Equipment in accordance with good industry practices, and has complied with specific recommendations of the Company. Accessories and equipment furnished by the Company, but manufactured by others, shall carry whatever warranty the manufacturer conveyed to the Company and which can be passed on to the Purchaser. The Company shall not be liable for any repairs, replacements, or adjustments to the Equipment, or any costs of labor performed by the Purchaser without the Company’s prior written approval.

The Company makes no performance warranty unless specifically stated within its proposal, and the effects of corrosion, erosion, and normal wear and tear are specifically excluded from the Company’s warranty. In the event performance warranties are expressly included, the Company’s obligation shall be to correct in the manner and for the period of time provided above.

THE COMPANY MAKES NO OTHER WARRANTY OR REPRESENTATION OF ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED. THIS WARRANTY SUPERSEDES ALL PREVIOUS WARRANTY STATEMENTS.

This warranty does not apply to electric motors or gasoline engines. These are covered by the Original Manufacturer’s Warranty and should be returned (by the customer) to their authorized service center for service.

Correction by the Company of non-conformities, whether patent or latent, in the manner and for the period of time provided above, shall constitute fulfillment of all liabilities of the Company and its distributors for such non-conformities with respect to, or arising out of such Equipment.

LIMITATION OF LIABILITYTHE REMEDIES OF THE PURCHASER SET FORTH HEREIN ARE EXCLUSIVE, AND THE TOTAL LIABILITY OF THE COMPANY, ITS DISTRIBUTORS AND SUPPLIERS WITH RESPECT TO CONTRACT OR THE EQUIPMENT AND SERVICES FURNISHED IN CONNECTION WITH THE PERFORMANCE OR BREACH THEREOF, OR FROM THE MANUFACTURE, SALE, DELIVERY, INSTALLATION, REPAIR OR TECHNICAL DIRECTION COVERED OR FURNISHED UNDER CONTRACT, WHETHER BASED ON CONTRACT, WARRANTY, NEGLIGENCE, INDEMNITY, STRICT LIABILITY OR OTHERWISE, SHALL NOT EXCEED THE PURCHASE PRICE OF THE EQUIPMENT UPON WHICH SUCH LIABILITY IS BASED.

THE COMPANY, ITS DISTRIBUTORS AND ITS SUPPLIERS SHALL IN NO EVENT BE LIABLE TO THE PURCHASER, ANY SUCCESSORS IN INTEREST, OR ANY BENEFICIARY OR ASSIGNEE OF THE CONTRACT FOR ANY CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL OR PUNITIVE DAMAGES ARISING OUT OF THIS CONTRACT OR ANY BREACH THEREOF, OR ANY DEFECT IN, OR FAILURE OF, OR MALFUNCTION OF THE EQUIPMENT, WHETHER OR NOT BASED ON LOSS OF USE, LOST PROFITS OR REVENUE, INTEREST, LOST GOODWILL, WORK STOPPAGE, IMPAIRMENT OF OTHER GOODS, LOSS BY REASON OF SHUTDOWN OR NON-OPERATION, COST OF PURCHASE OF REPLACEMENT POWER, OR CLAIMS OF PURCHASER OR CUSTOMERS OF PURCHASER FOR SERVICE INTERRUPTION, WHETHER OR NOT SUCH LOSS OR DAMAGE IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, INDEMNITY, STRICT LIABILITY OR OTHERWISE.

Warranty Statement

Atlas Copco Compressors, LLC

1800 Overview Drive

Rock Hill, SC 29730

877-861-2722