Air-Alarm1 Manual v8

8/3/2019 Air-Alarm1 Manual v8

1/28

Air-AlArm1

D.i.Y. Wireless Home AlArm sYstem Kit

Users mANUAl


2/28

Cpygh Nc

This manual is urnished under license and may be used or copied only in accordance with the terms o such license. Except as permitted by such license, nopart o this publication may be reproduced, stored in a retrieval system, or transmitted, in any orm or any means, electronic, mechanical. Recording, or otherwise,including translation to another language or ormat, without the prior written permission o SecurityMan. The content o this manual is urnished or inormationaluse only, is subject to change without notice, and should not be construed as a commitment by SecurityMan. SecurityMan assumes no responsibility or liability orany errors or inaccuracies that may appear in this document. All other product names, trademarks and registered trademarks in this document are the propertieso their respective holders. FCC Inormation Notes on FCCs Consistent Statement o Inormation This product meets the requirements specied in Part 15 o FCCRegulation. Operation rests with the ollowing two conditions:(1 ) The equipment should not cause any harmul intererence .(2 ) The equipment must receive and process any intererence, including any possible intererence caused by operation mistakes .

Waany

SecurityMan warrants this product will be ree rom deects in materials and workmanship or the period o time specied on the product packaging. This limitedwarranty shall commence rom the date o purchase. SecurityMan Products warranty is not transerable and is limited to the original purchaser. I the product isound to be deective then, as your sole remedy and as the manuacturers only obligation, SecurityMan will repair or replace the product. This warranty shall notapply to products that have been subjected to abuse, misuse, abnormal electrical or environmental conditions, normal wear and tear or any condition other than

what can be considered normal use.

lan lay

The liability o SecurityMan arising rom this warranty and sale shall be limited to a reund o the purchase price. In no event shall SecurityMan be liable or costs oprocurement o substitute products or services, or or any lost prots, or or any consequential, incidental, direct or indirect damages, however caused and on anytheory o liability, arising rom this warranty and sale. These limitations shall apply not withstanding any ailure o essential purpose o any limited remedy.

scuyman

4601 E. Airport Drive, Ontario, CA 91761, USATel: 888-977-777 or 909 -20-6668Fax: 909-20-6889Email: [email protected]: http://www.securitymaninc.com

Copyright 2008 by SecurityMan v4.0


3/28

tAble o CoNteNts

inducn

Packag Cnn

man auAa H (sm8088e)

Alarm Host Specications (SM-8088E)

Three types o Deense Line

Programming the Alarm Host (SM-8088E)

To Setup User Code (For Ademco Managemant Center)

How to change the programming password

Operation

Undand and sup W Acc

Wireless Remote Controllers (SM-88X)

Wireless Door/Window Sensor (SM-87B)

Wireless Wide-Angle PIR Motion Sensor (SM-80)

Wireless Indoor Siren (SM-10W)

Wireless Smoke Alarm (SM-9, optional)

Wireless Outdoor Siren (SM-10, optional)

Wireless Panic Button (SM-89, optional)

Air-Alarm Deense Zone Code Chart

Manuacturer Wireless Deault Setting

Cn P and sun

Day mannanc and Ca

Accessories

A Aa quny Akd Qun

1

1

1

2

4

5

5

6

8

8

9

11

1

14

15

17

19

19

20

22

22

23


4/28

1

inducn

SecurityMan Air-Alarm1 is a state-o-the-art wireless alarm system kit or homes and businesses. It is user-riendly and easy to use protecting homes/

businesses at a minimum cost o investment. Do-It-Yoursel installation and monitoring alarm system without monthly ees is a key benet or users. The

system will alert by phone calls to owner through a series o enlisted phone numbers. The owner can then dial into the host to arm or disarm the alarm byusing the phones numeric keypad. The Air-Alarm1 system can be upgraded by adding up to 60 wireless sensors, sirens, and up to 8 remote controllers.

Packag Cnn1 x Air-Alarm1 host with built-in LEDs, keypad, and speaker.

1 x Host Anchor Card or Fixed Position.

1 x 12VDC Power Adapter

1 x Wireless Wide-Angle PIR Motion Sensor with Mounting Bracket (Battery Included)

1 x Wireless Magnetic Door/Window Sensor with Mounting Bracket (Battery Included)

1 x Wireless Indoor Siren

2 x Wireless Remote Controller (Battery Included)

1 x Phone Cable(t)

1 x Warning Sign

1 x Users Manual

Accessories (on page 22)

man au

Easy-to-use and cost-eective D.I.Y. (do-it-yoursel) wireless intruder alarm system kit.

Supports up to 60 wireless sensors (15 wireless deense zones and 4 wireless sensors per zone).

Transmit at 40-4MHz requency band, wireless transmitting distance up to 00 eet (remote controller, smoke sensor, and siren) and up to 450eet (magnetic door/window sensor & PIR motion sensor)

Supports up to 5 phone numbers or auto alarm call and 1 management center protocol (CID).

Armed/disarmed by remote controller, phone call, or hosts keypad.

Easy one-key armed/disarmed operation.


5/28

Programmable silent alarm or audible alarm.

Recordable alarm voice message (up to 9 seconds record time).

Telephone line disconnection alarm sound every 5 seconds.

Smart deense lines coniguration-1st deense line is the perimeter, 2nd deense line or in-room, & 24-hour deense line.

Internal rechargeable backup battery in alarm host lasts up to 8 hours.

Battery included or remote controllers, wireless door sensor, and wireless motion sensor last up to 2 years.

Programmable password.

Ademco CID compatible protocol

Aa H (sm8088e)

In o mode, the alarm host will still operate normal i the AC power is connected.*

For wall mount please use screw* (b) (see page22)

2


6/28

Aa H spccan (sm8088e)

Operating power: 9-15VDC

Static current: 60mA

Alarm current: 80mA

Operating environment: Temperature: -10 ~ 50C Humidity:


7/28

4

Pgang h Aa H (sm8088e)

_uncn_:_opan__Operation Explanation

Notes:

1. The alarm host will automatically exit rom the programming status i inactive or 20 seconds.2. Programming is eective ater _SET+Password+ENT_, use ESC button to go to previous step.

. The alarm host will beep in series to indicate the operation is successul and beep once to indicate operation ailure.

_:_set + Pawd + eNt__ This command applies throughout whenever programming the alarm host, beore attempting to change other programmingeatures, such as Delay Time to Arm, Delay Time to Alarm, Emergency Alarm Voice, Adding and Cancelling wireless devices, etc . For example; to change

Delay Time to Arm below rom the deault 40 seconds to 1 minute, press_SET + 888 + ENT_ ollow by _15 + ENT_. The programming deault password is

888 ( digits long), and 15 is the

programming code or 1 minute.

_inpu Aa tphn Nu_ : _XX + eNt + tphn Nu + eNt__ XX indicate telephone group number which can be o personal numbers

or management center. See group details below:

01: Group 1 (personal telephone number)

02: Group 2 (personal telephone number)0: Group (personal telephone number)

04: Group 4 (personal telephone number)05: Group 5 (personal telephone number)

06: Group 6 (reserved or CID Protocol number or management center, not or personal numbers, requires monthly ees)

To delete or reset the telephone enlisted number press, SET+password+ENT+XX+ENT+ENT (XX is the group number, ie. 01, 02, etc.)

_Day t A_: _XX + eNt__ Setup a dwell time in which the alarm will become activated or armed. Enter 10 or XX to setup Delay Time to Arm or

40 seconds, enter 15 to setup Delay Time to Arm or 1 minute and press the ENT button to conrm. The deault setting is 10 or 40 seconds alarm dwell time.

I armed, any wireless triggers within the dewll time o 40 seconds or 1 minute, the Alarm Host will beep twice.

_Day t Aa_: _XX + eNt__ Setup a dwell time in which the alarm will sound or trigger. Enter 20 or XX to setup immediate alarm sound trigger-

ing, enter 21 to setup a 15 seconds Delay Time to Alarm. The deault setting or Delay Time to Alarm is 20.

_egncy Aa sund_: _XX + eNt__Enter 0 or XX to disable Emergency Alarm Sound, enter 1 to setup audible alarm sound, the deault is 1.During the Emergency Alarm Sound is disabled or set to 0; the alarm host will operate normal, and will continue to dial the enlisted phone numbers in

case o emergency.


8/28

5

_Aa sund 1 and 2nd dn n_: _XX + eNt__ Enter 40 or XX to disable alarm sound or 1st & 2nd deense line, enter 41 to enable Audiblealarm, the deault is 41. When the Alarm Sound is disabled or set to 40; the alarm host will operate normal and will continues to dial the enlisted phone

numbers upon alarm trigger.

_tphn Dcnncn Aa_: _XX + eNt__ Enter 60 or XX to disable Telephone Disconnect Alarm, enter 61 to enable Telephone Disconnect Alarm,the deault is 61. Telephone Disconnection Alarm is line o integrity alarm. That chirps every 5 seconds when the telephone line is not connected to the TEL

IN port o the alarm host panel. To disable the chirping when the telephone is not plugged in to the host ; press, SET+password+ENT+60+ENT.

_t upad a/da anagn cn_: _XX + eNt__Enter 50 to disabled upload, enter 51 to enable upload to management center, the deaultsetting is 50 or disable. Leave this disable i management center is not in service.

_U Cd_: _80 + eNt + XXXX + eNt__ Enter a number between 0000~9999 or XXXX to setup user code or management center. The deault is set asrandom; apply to management center use only.

t sup U Cd ( Adc managn Cn):

_set + 999 + eNt + p un + eNt + n pgang cd + eNt + 3 dg u cd + eNt + n u cd + eNt__ press

SET and programming will appear, enter 999 press ENT and then press page up/down to choose revise users code and press ENT, enterprogramming code, press ENT enter 6 digits users code, and press ENT, reenter users code, and press ENT.

Note: users code cannot be same as programming password 999 and programming code! Press ESC to exit rom programming when fnished.

Hw chang h pgang pawd

_set + 999 + eNt + th Dg Nw Pgang Pawd + eNt + th Dg Nw Pgang Pawd + eNt__Press SET button, the

programming LED light will come on, enter 999, press ENT, then input a new three-digit programming password, press ENT, re-input the new three-digit

programming password, and then press ENT to complete the programming password change. Notice the programming LED light will disappear ater thenal ENT is pressed.


9/28

6

opan

t rcd a vc ag gng: Slide the switch on the let side o the alarm host to the RECORD ON position, press and hold the microphone

button, speak close (6) into the rear speaker o the host, and then release the microphone button when nished with your voice message greeting.

Voice message greetings can be anywhere between 0~9 seconds long.

t Payack h cdd vc ag gng: Slide the switch on the let side o the alarm host to DC ON, press and hold the playback button

to playback the recorded voice message greeting. An alarm sound message is pre-recorded by deault.

onky A:

by r cn: Press the AWAY (All Alarm) or the HOME (Part Alarm) button on the remote control to arm and the alarm host will beep once to

conrm the operation is successul. See Wireless Remote Controller on page 8 or more detail.

by Kyad n aa h: Press (All Alarm) or (Part Alarm) button, the alarm host will beep once to conrm the operation is successul.

onky Da:

by r cn: Press the DISARM button on the remote control to disarm the alarm and the alarm host will beep twice to conrm the operation is

successul.

Da y kyad n aa h: _esC/Da + Pgang Pawd + eNt__ Press the ESC/Disarm button ollow by the programmingpassword and then ENT to disable alarm siren using the alarm host. The host will beep twice to conirm the operation is successul.

egncy/Panc D:

by r cn: Press the EMERGENCY button on the remote control at times o emergency to immediately activate the sound siren on thealarm host and wireless sirens.

by Kyad n aa h: Press the EMERGENCY button on the alarm host at times o emergency to immediately activate the siren sound on thealarm host and wireless sirens.

tphn aa: Ater receiving the phone call rom the alarm host, the recorded voice message will repeatedly play or 22 seconds. Beore the 22seconds are over, one o the ollowing actions must be taken:

A) Press the number 8 on the phone pad to extend the time intervals or an additional 20 seconds to enter the listening state. In the listening statethe built-in microphone on the alarm host will be active to pick up any sound that takes place near by the alarm host.

b) Press the pound # button to replay the recorded voice message.


10/28

C) Press the star * button, the host will end/drop the call and stop to dial the next enlisted alarm telephone numbers. Ater the * is pressed; thealarm host will resume to be armed

N: h qud n d p h aa h cnnung da h nx nd phn nu.

D) Hang up the telephone without any command input, the host will end the call and automatically continues to dial the next enlisted alarmtelephone numbers.

lng danc a y phn: 0 seconds ater successully dialing the telephone number o alarm host, there will be: a beep > enter programming

password o host > beep > enter 1 > beep, and the host will then automatically hang up ater the last beep to successully complete the operation.N: lng danc a y phn qu h aa h ad n h Away d.

lng danc da y phn: 0 seconds ater successully dialing the telephone number o alarm host, there will be: a beep > enter programming

password o host > beep > enter 0 > beep, and the host will then automatically hang up ater last beep to successully complete the operation.

Aa dang d: Ater the alarm host triggers or goes o, the alarm host will start to dial the rst enlisted telephone number, then the second, third,

ourth and so on. Unless one o the enlisted telephone numbers answers otherwise this routine auto dial will continue through a series o loop or threetimes.

Aa py: I the telephone line is busy when the alarm host goes o, the alarm host will automatically cut o the busy/used line and resume auto-

matic dialing to the enlisted alarm telephone numbers to advise o the crime.

tphn n dcnncn Aa: I the telephone line is cut or comes o the hook, the host will beep every 5 seconds ater the telephone line has

been cut o or disconnected. It will continue to beep until the phone line is xed or reconnected.

AWAY md (Zn 1~15): In this state, ater any detection in the 1st, 2nd, or 24hr deense line is triggered, the alarm host will immediately sound the

sirens and at the same time automatically dial the enlisted alarm telephone numbers in sequence.

Home md (Zn 6~10): In this state, ater any detection in the 1st or 24hr deense line is triggered, the alarm host will immediately sound the sirensand at the same time automatically dial the enlisted alarm telephone numbers in sequence. In HOME mode, the 2nd deense line will be disabled and will

not trigger the alarm host.

7


11/28

Undand and sup W Acc

Please note that all the devices included with the Air-Alarm1 kit is paired to the Alarm Host (panel) by deault. I sensing devices does not trigger theAlarm Host, please reerence to the To Add: instructions in the users manual to add the wireless devices accordingly. All newly add-on sensing devices is

required to be pair with the Alarm Host.

W r Cn (sm88X)

uncn/au:

Used to arm & disarm alarm host.

Emergency button or emergency or panic help.

spccan:

Operating power: 27A 12V Battery (Recommend: alkaline battery)

Wireless Transmitting distance: 00t (in open area)

Service lie: 2 years

inaan and Uag:

Ideal or keychain and to take with you when the alarm host is in the AWAY mode.

Press the AWAY button to arm beore leaving home and press the DISARM button to disarm.

8


12/28

9

Press the HOME button to part arm or 1st deense line enable to protect the perimeters o your home at night time beore going to sleep.

Please replace the battery within 2 years o usage or any time when it becomes less sensitive or has a shorter controlling distance.

Addng & Cancng r Cn.

To Add:

Press_ set + Pawd + eNt_then.

_ 70 + eNt+ 00 + eNt the Learn light will appear solid red.

Press any button on remote controller twice consecutively, the alarm host will beep in series and the Learn light lashes ive times and thenturns o to indicate the remote control has been successully added.

To Cancel:


_ 71 + eNt+ 00 + eNt the alarm host will beep in series then the Learn light lashes once and then turns o to indicate the

remote control has been successully cancelled.

N: th aa h can ny an 1 cn a a , a a 8 cn can addd a h.

W D/Wndw sn (sm87b)

For Mounting Holes, please use screw* (C) or adhesive sticker. (seepage22)

For Mounting Bracket, please use screw* (D). (Magnetic underlaymount use or uneven surace) (see page22)


13/28

10

uncn/au:

Mainly detect open/close states o doors and windows, generally set as a 1st Deense Line or perimeters.

I any doors or windows are opened, it will transmit the alarm signal to notiy the alarm host.

spccan:

Operating power: 2A or 27A 12V Battery (Recommend: alkaline battery)



Alarm Distance:


14/28

W WdAng Pir mn sn (sm80)

uncn/au:

Mainly monitor and control indoor stereoscopic spaces, generally set as a 2nd Deense Line.

When human body enters the detection areas, the motion sensor will transmit the alarm signal to the alarm host.

It is immune to pets; cats, dogs, etc that are less than 10KGS will not cause alse alarm.

spccan:

Operating power: 9V Battery (Recommend: alkaline battery)



Detection Area: 110 10 x10m11

Please use screw* (e) to install the bracket(see page22)


15/28

12

inaan and Uag

Mount the bracket to a desired wall surace, location, or corner at a height o about 6t to 7t above the ground.

Open the sensor cover and connect a 9VDC battery. Next, reers to the diagrams above to adjust and select the Jumper Line timer between

5S or 5MIN or the motion sensor to detect once every 5 seconds or the sensor to detect once every 5 minutes. Recommended to use5Sdeault setting or normal use. Skip To Add motion sensor below or newly added motion sensor beore closing the sensor cover and

proceed to the next step.

Match the grooves o the sensor to the bracket and slide the motion sensor down rom top to bottom to secure.

Adjust the sensor to a proper angle and then slide the power switch located on the side to the ON position. The motion sensor takes 0seconds to become active or operation (normal working state) a ter switching ON.

A red light will lash or motion detection, a requent green light lashing means it is time to replace the battery.

Addng and Cancng Pir mn sn

To Add:Press_ set + Pawd + eNt_then.

_ 70 + eNt+ XX + eNt The Learn light will appear solid red.

N: th XX ndca gup nu h 2nd dn zn, ncudng zn 11 hugh zn 15.

Press the Learning Emitting Switch twice consecutively to trigger PIR sensor, the alarm host will beep in series, and the Learn light lashesive times and then turns o to indicate the PIR motion sensor has been successully added.

To Cancel:


_ 71 + eNt+ XX + eNt The alarm host will beep twice then the Learn light lashes once and then turns o to indicate the PIR

motion sensor has been successully cancelled.

N: th aa h can ny an 1 w dvc (W WdAng Pir mn sn) a a , a a 4 w dvc (Pir

mn sn) a zn/gup can addd. xap; h 2 dn n, 4 n w addd zn/gup 11

hugh zn / gup 15, a 20 n n a. i 1 dvc vd a gup ha ha 4 dvc, hn a 4 dvc n h gup w

auacay vd, and ach dvc() w hav addd agan h aa h.


16/28

W ind sn (sm103W)

uncn/ au:

Wireless receiving indoor alarm siren, spot alarm sound and lashes

Plugs into wall outlets, or indoor use only.

spccan:

Operating Power: 100240VAC

Wireless Receiving distance:00 t (In open area )

Siren Sound 105dB

inaan and Uag:

Plug the wireless indoor siren into a power outlet.

Recommendated to install 4~5t high rom the ground.

Addng and Cancng ind sn

To Add:Ater connecting the siren to the power outlet, press the Learning button located on the let side o the siren and the siren light will comeon.

Press the button on the alarm host (remote control not applicable) to sound o the sirens, then disarm by using the alarm host

1

k d b d h l h ll b d h d h b


17/28

keypad by pressing _esC/Da + pgang pawd + eNt_, the alarm host will beep twice to indicate the indoor siren has beensuccessully disarmed.

The light on the siren will lash 5 times to indicate the indoor siren has been successully added.

To Cancel:

Ater connecting the siren to the power outlet, press and hold the Learn button located on the l et side o the siren or 5 seconds, the lighton the siren will lash once to indicate the indoor siren has been successully cancelled.

N: th aa h can ny an 1 w dvc (ind sn) a a , up w n can addd a h. Whn addng

cancng w n, ny pa ung h aa h kypad; d n u h cn da n h pc.

W sk Aa (sm93, pna)

uncn/au:

Monitor and control indoor ire risks, or indoor use only, generally set as a 24 hour Deense Line.

Replace the battery every 2 years (varies on usage).

Usually installed to ceilings o living room, hallways, aisles, etc.

14

Please use screw* () or mounting bracket (see page22)

s


18/28

spccan:

Operating power: 9V Battery (Recommend: alkaline battery



Monitor volume: 480t3

Addng and Cancng sk Aa



N: th XX ndca gup nu h 24 hu dn zn, ncudng zn 01 hugh zn 05.

Press the Test Button twice consecutively to trigger the smoke alarm sensor, the alarm host will beep in series, the Learn light will lashive times and then turns o to indicate the smoke alarm sensor has been successully added.

To Cancel:


_ 71 + eNt+ XX + eNt The alarm host will beep twice, the Learn light lash once and then turns o to indicate the smoke alarmsensor has been successully cancelled.

N: th aa h can ny an 1 w dvc (sk Aa sn) a a , a a 4 w dvc (sn) a zn/gup

can addd. i 1 dvc vd a gup ha ha 4 dvc, hn a 4 dvc n h gup w auacay vd, and

ach dvc() w hav addd agan h aa h.

W oud sn (sm103, pna)

15

Please use screw* (G) to mount. (see page22)

uncn/au:


19/28

16

uncn/au:

Nice, exquisite and weatherproo.

Micro-computer controller, steady perormance and quality.

Study up to 10 pieces to a host.

Built - in rechargeable battery or backup, automatic switches between AC powers to DC power in cases o emergency outage.

Low standby power consumption, low battery voltage LED detection, resumes charging automatically.

Wall mount installation

spccan:

Operating power: 110~240VAC_50Hz

Static power consumption: 40 mA

Working power consumption: 450 mA

The maximum alarm sound duration with lash: Minutes

Receiving distance: 00t (in open area)

Built-in Rechargeable battery 6VDC 100mA (up to 100 hours stand-by)

Alarm Siren Sound 120dB

IP51

inaan and uag

Plug in the AC power to an outlet; press the green button to enable the backup battery located on the back side o the outdoor siren.

Study the siren to the alarm host according to the activation and deactivation instructions below.

Unplug the siren rom the AC power plug ater you inish studying and ind a proper location (Outdoor/indoor) to mount it , then plug in theAC power.

The alarm sound and red LED lash lasts up to minutes i the alarm host is not disarmed within the minutes.

When the backup battery has a voltage that is equal to or less than 5VDC, the charging indicator (solid red) light will come on to representcharging status. The rechargeable battery takes approximately 20 hours to be ully charged and then the charging indicator light will turn

o.

Acvang and dacvang oud sn

To Activate:

Siren: Connect the siren to an AC power outlet > press the red Study button located on the back o the siren > the red siren lights will

turn ON.


20/28

17

Alarm Host: Press emergency button on the alarm host to sound o the alarm and then disarm the alarm by using the _ esC/Da +pgang pawd + eNt_, the alarm host will beep twice to indicate the outdoor siren has been successully disarmed

The light on the siren will then lash 5 times to indicate the outdoor siren has been successully added.

N: on n can udd a a , up 10 w aa n a h.

To Deactivate:

Press and hold the Study red button or 10 seconds, the siren will lash once to indicate the Outdoor siren has been successully deactivated.

W Panc bun (sm89, pna)

uncn/au:

Used or emergency panic, generally set as a 24 hour Deense Line.

Placed under tables, beside bed whenever pan ic is needed.

Replace battery every 2 years (varies on usage).

spccan:

Operating power: 2A 12V Battery (Recommend : alkaline battery)

Wireless Transmitting distance > 450t (in open area)

Service lie: < 2 years

To mount, please remove the back cover*and use screw (H). (see page 22)

inaan and uag


21/28

18

inaan and uag

Installed in living rooms, bedsides, carry along, etc.

For emergency use, scared away intruders; sends out emergency signal to alarm host to sound o the siren(s). This is a 24 hour standby

zone or panic or emergency use only.

Please change the battery when the signal distances become shorter or every 2 years.

Addng and Cancng Panc bun



N: th XX ndca gup nu h 24 hu dn zn, ncudng zn 01 hugh zn 05.

Press the Alarm button twice consecutively, the alarm host will beep in s eries, the Learn light will lashes ive times and then turns o to

indicate the panic button has been successully added.

To Cancel:Press_ set + Pawd + eNt_then.

_ 71 + eNt+ XX + eNt The alarm host will beep twice, the Learn light will lash once and then turns o to indicate the panic

button has been successully cancelled.

Note: The alarm host can only learn 1 wireless device (Panic Button) at a time, a total o 4 wireless devices (Panic Buttons) to a zone/group can be

added. I 1 device is removed rom a group that has 4 devices, then all 4 devices in the group will be automatically removed, and each device(s) will

have to be added again to the alarm host.

AAa1 Dn Zn Cd Cha:


22/28

19

Deense Zone Code Deense Zone Type Bypass Zone Delay Time to Alarm Compatible Accessories Remark

00 No No

Wireless Remote Controller

& Wireless Remote Control

Keypad

Up to 8 RC

1 to 5 24-hour Deense Line No No

Wireless Smoke Alarm,

Wireless Gas Alarm, & Panic

button.Each deense

zone supports

up to 4 wireless

devices.

6 to 10 1st Deense LineYes (zone 11

to15)Yes

Wireless Door Magnet &

Wireless Curtain PIR Sensor

11 to 15 2nd Deense LineYes (zone 6

to 10)Yes

Wireless Wide-Angle PIR

Motion Sensor

A Aa1 Dn Zn Cd Cha:

manuacu W Dau sng:

Wireless

Sensor Type

Remote

Control

Wireless Door/

Window Sensor

Wireless Wide-

Angle PIR Motion

Sensor

Wireless Curtain

PIR Sensor (N/A)

Wireless Gas

Alarm (N/A)

Wireless

Smoke

Alarm

Panic

Button

The deault

Deense

Zone Code

00 06 11 --- --- --- ---

Note : I ater setup the alarm system becomes uncontrollable or abnormal; please remove or cancel all o the deault setting o wireless devices

such as the remote control, door/window sensor, wide-angle PIR motion sensor, smoke alarm and then add (re-program) them back into to a desired

deense zone code

Cn P and sun


23/28

20

P P Cau sun

The alarm host sounded o immediately

ater connecting the power

The telephone incoming line has not

been connected, poor connection or

short circuit.

Double check, test and secure the incoming telephone line

or use a standard phone to test the line to ensure working

status.

The alarm host cannot record or partially

records

The record switch is not turned on. The

Record buttons not pressed down and

held while attempting to record, or not

held down all the way.

Slide the record switch to the ON position; Securely

press and hold down the RECORD button during recording.

Speak up close to the rear speaker o the host.

Repeatedly receiving the alarm telephone

No one picked up the alarm calls or

ailure to press the * star button to end/

drop the call.

Ater answering the alarm phone calls and hearing the

recorded message: please advanced to page 5 (tphn

Aa) o this users manual as a reerence to try to resolve

this problem, or simply press the * star button to end thecall.

The alarm host does not sound the

alarm ater the detector triggered the

alarm in armed mode.

1. The wireless devices may not havesynchronized with the alarm host.

2. The dwell time or Entry Delay or Exit

Delay has not been reached.

1. In Home mode, make sure the sensor or wireless devices

triggering is not in the 2nd Deense Line. Simply cancel thewireless devices and add them in again to synchronize with

the host.

2. Ensure the sensor detectors are not active within the

system setup Entry Delay Time or Exit Delay Time, deaultdelay time is 40 seconds

The PIR motion sensor does not work

Weak battery power, not switched on,

or the PIR motion detector is in the

power-down mode

Open the sensor shell to install the battery and slide the

power switch to On. Power down mode may be in aect:

5S: detect once every 5 seconds 5MIN: detect once every

5 minutes, please reers to the users manual or PIR setup.

Cn P and sun


24/28

21

The detecting distance o PIR motionsensor gets shorter

The ambient temperature in the detect-ing area is too high.

When the ambient temperature in the detecting area ex-ceeds the human body temperature, the detecting distance

will get shorter, its normal.

The alarm host does not alarm ater the

new added wireless detector is triggered.

Failed to ollow the operation instruction

o Adding and Cancelling sensors/devices o newly added wireless sensor(s)

Follow the operation instruction o Adding and Cancel-

ling to activate the new wireless sensor(s)

The PIR motion sensor fashes requently

in green.Battery is drained or low.

Replace with new battery o the same voltage specica-

tion.

The door/window sensor indicator fashesrequently in green ater alarming.

Battery is drained or low. Replace with new battery o the same voltage specica-tion.

The distance o the remote controller gets

shorter.Battery is drained or low. Replace with new batter o the same voltage specication.

Day mannanc and Ca


25/28

y

This alarm system is hi-tech with outstanding design unctionality and sophisticated product eatures which should be used careully. To make the alarm

system operable long term and prolong the service lie; the ollowing are strongly recommended:

1. Install the alarm system and alarm host in dry and well ventilated locations.

2. Do not put the alarm host or any wireless sensors in extreme cold, extreme heat or excessively dusty places. This is to

prevent shortened lietime o the products, including the internal electronic parts and the plastic housings rom being

exposed to harsh conditions.

. Do not install the wireless alarm system in low, easy to reach, and exposed places to prevent the children rom tamperingwith or thieves easy access.

4. Regular scheduled testing is necessary to help prevent system ailures and resolve problems in time.

5. Check batteries in all wireless sensors and replace them as needed to ensure normal operation.

6. Power o and remove all batteries rom all wireless system beore storing them on shelves.

Acc:

Add-on(optional):

22

Adhesive sticker

AAa1 quny Akd Qun


26/28

2

y

Q1: i i hav an anwng achn und n w i a ca n a/da h h?

A1: No, please be sure to turn o the answering machine on the telephone or the alarm host to be able to receive incoming calls. The act that most

answering machines will answer within 6 or 7 rings and our Air-Alarm1 system requires about 15 seconds in order to receive incoming signals and allowarm/disarm, the answering machine will pick up the signal beore Air-Alarm1 host i the answering machine is not turned o while away rom home.

Q2: Hw can i y AAa1 ccy ad avng h?

A2: Please make sure to arm the alarm host and check to see i the red LED light comes on armed, once certain then leave home. From the moment it isarmed, there will be 40 seconds to 1 minute delay time to leave home depending on the dwell time setup.

Q3: my n n ud nugh; i cud ay ha h whn i a andng ud?

A: Install the siren closer to the windows, open space, add more indoor sirens or add an outdoor siren or louder siren sound.

Q4: D h annna n h AAa1 y hav xndd uwad na u?

A4: No, extending the antennas outward may not be necessary i the area o installation has adequate reception. However, in an area with weak recep-

tion, extending the antenna will provide maximum perormance.

Q5: D h AAa1 upp dan a/da nad hnd a up n dga phn y?A5: No. Currently Air-Alarm1 can only unction through a dedicated phone line, such as; a PSTN (Public Switched Telephone Line), home phone line (aka.

POTS - plain old telephone service). Air-Alarm1 do not support VOIP (Voice Over Internet Protocol) digitaltelephone service.

Q6: my AAa H nny und f h aa dung da d?

A6: Please switch the power on the let side o the Alarm Host to the OFF position and disconnect the power jack rom the Host. Wait or several min-

utes and then plug the power jack back into the Alarm Host and switch the power to the ON position.

Q7:th AAa wa wkng and nw h w dvc w n gg h Aa H?A7: Please ollow the To Add: instructions or each device and add all the wireless devices back to allow synchronization with the Alarm Host.

Q8: Whn i wch n y Pir n n cnnuuy gg h Aa H vn whn h H n ad?

A8: Turn OFF the PIR sensor, open the cover o the PIR sensor, place the PIR sensor towards a wall to avoid ault triggering, reerence pg12 o the manualTo Add: the PIR sensor again to zone 11 (deault zone or PIR sensor).

Q9: D i nd add ach h w dvc ha c wh h k h Aa H?

A9: No, each wireless device inside each Air-Alarm kits is already added by deault.

Q10: Hw can i ca h nd phn nu h ?

A T l h li d l h b SET d ENT ( ) ENT ENT O i l dd h li d l h


27/28

24

A10: To clear the enlisted telephone numbers press; SET+password+ENT+01 (01~05 group no.)+ENT+ENT Or simply add the enlisted telephone num-

bers to the same group to override the old.

Q11: my Aa H kp n ggng dung n cng and u gng ca?

A11: Please disable the Telephone Disconnection Alarm by entering the ollowing command; SET+password+ENT+60+ENT

Q12: Hw d sm80 Pir mn sn wk and why n nv nugh?

Q12: SM-80 PIR Motion Sensor areas o detection is 110 degree, 0x0t. It is immune to animals that are equal to or less than 10kgs in weight, ie. dogs,cats, etc.

1)SM-80 can become less sensitive i the battery becomes weak; replace new 9VDC battery.

2)Try removing the sensor by ollowing the To Cancel procedure in the user s manual and then ollow the To Add and add it into another zone o the

Alarm Host.

)Power cycle both PIR motion sensor and Alarm Host.

Here is some examples o testing methods that is not recommended or SM-80 PIR Motion Sensor:- Shaking one hand in the ront o the PIR Motion Sen-

sor. It might not sense well because the IR radiation rom one hand may be too small to detect.- Moving an object (none temperature object), like a stick

in the ront o the PIR Motion Sensor. It may not sense because sticks in general does not emit IR radiation.- Moving out o the detection areas.


28/28

www.securitymaninc.com

Air-Alarm1 Manual v8

Documents

Transcript of Air-Alarm1 Manual v8