Ag Catalog Jan 2008

Wheels and tiresfor:

Combines

Cotton Pickers

Fertilizer Spreaders

Forestry Equipment

Grain Carts

Harvesters

Implements

Irrigation

Skid Steers

Sprayers

Tractors

Trailers

Utility Vehicles

Wagons

Number 101/Sep 2000

Agricultural Products Catalog

For Promotional Use Only

keith.heeres

Text Box

Number 102/Jan 2008

1

This catalog has been created specifically to show the sizes and types of wheels andrims which are available for agricultural applications.

The task of servicing tires and wheels can be extremely dangerous and should beperformed by trained personnel only, using the correct tools and following specificprocedures. Failure to heed this warning could lead to serious injury or death. Wesuggest that the following is mandatory reading for all those involved in the servicingof tires and wheels:

Department of Labor Occupation Safety and Health Administration(OSHA) 29 CFR part 1910.177 entitled Servicing of Singe Piece and Multi-piece Rim Wheels. NOTE: Single piece rims have the rim made out of asingle piece of material as shown in this Agricultural Catalog andmultiple-piece rims have a loose flange or flanges and lock ring asdepicted in the Forestry section of this catalog.

Rubber Manufacturers Association, “Care and Service of Farm Tires.”

This and any other safety related information is issued as assistance to supervisoryand operational personnel in the actual tire/rim service environment. Theresponsibility for implementation of this safety information rests with operational andsupervisory personnel carrying out the actual service work. Read and fullyunderstand all tire changing and safety procedures before attempting tire/wheelservicing.

If you have any doubt about the correct, safe method of performing any step in thedemounting, mounting, adding or removing fill, or inflating process STOP! Seek outexpert assistance from a qualified person.

Personnel involved in servicing tires and wheels should always wear protectivegloves, footwear, safety glasses, hearing protection and appropriate head gear.

Further references explaining safety procedures can be found in literature publishedby the Rubber Manufacturers Association, Washington D.C.; the National Tire Dealersand Retreaders Association, Washington D.C.; the National Wheel and RimAssociation, Jacksonville, FL; and OSHA, Washington, D.C.

WARNING!

2

Terms of Purchase ................................................................................................4Warranty Statement ..............................................................................................4Return Policy ........................................................................................................5Definitions and Explanations ................................................................................6How to Measure a Wheel ..................................................................................10Wheel application Data Sheet ............................................................................17Custom Built Wheels ..........................................................................................18Packaging and Handling ....................................................................................19Important Notice..................................................................................................20Small Agricultural Wheels ..................................................................................21SAE Wheels List ................................................................................................23More commonly used small agricultural wheels ................................................25Large Agricultural Wheels - Single Piece ..........................................................2832'' Vastyle Rims ................................................................................................30Large Agricultural Wheels - Waffle Wheels ........................................................31Large Agricultural Wheels - Rim and Clamp ......................................................34Bevel Mounted RIms ..........................................................................................46Power Adjust Style Wheels ................................................................................50Duals and Triples ................................................................................................54Tie Rod Duals ....................................................................................................55Custom Built Duals & Triples ..............................................................................57Hub Extensions and Wheels ..............................................................................58Straddle Dual Wheels for 30” Row Spacing ......................................................59Forestry Wheels..................................................................................................62Tires and Tire Mounting ......................................................................................67Appendix A—Wheel Size to Tire Size Conversion List ......................................70Appendix B—Tire Size to Wheel Size Conversion List ......................................86

Table of Contents

4

Terms of Purchase, Warranty and Returns Policy

Terms of PurchaseShipping Charges - All prices are F.O.B. OTR Wheel Engineering shipping facility unlessotherwise noted.

Customers will be notified of any extra charges for packaging of products for shipment.

Returns - All merchandise returned requires authorization and is subject to a restockingcharge (see return policy on the following page).

Custom Made Products - All customers are responsible for all merchandise built to theirspecifications.

Damage And Shortage Claims - Any damage or shortage must be noted on the delivery ticketor a carrier’s freight bill at the time of delivery.

Warranty - Warranty claims will only be considered on items sold by OTR Wheel Engineering.

WarrantyOTR Wheel Engineering, Inc., has no control over the end use or application of its productsas purchased or may be as modified, for use on equipment. Such use is subject to adequatefield testing and approval by the equipment manufacturer.

Should something go wrong with a part or parts purchased from OTR Wheel Engineering,Inc. within a period of ONE YEAR from date of purchase, OTR Wheel Engineering, Inc.’sReturn Policy is limited to replacement or repair of the parts based on satisfactory proof ofdefective workmanship or material. No adjustment will be made in cases of product abusesuch as overloading, excessive speeds, improper tire inflation, or operating in conflict withconditions as presented in the Tire & Rim Association Manual, or specifically recommendedand approved in writing by OTR Wheel Engineering, Inc., product engineering. We do notassume liability for parts remanufactured or applications beyond their intended use. A return policy is not to considered a guarantee of OTR Wheel Engineering, Inc. products.

A part or parts can not be returned to the factory without prior approval of OTR WheelEngineering, Inc. OTR Wheel Engineering, Inc. will reimburse freight charges for a part orparts shipped to its factory if:

a. OTR Wheel Engineering, Inc. has been called for authorization to ship the part or partsto its factory, and,

b. the part or parts are found by OTR Wheel Engineering, Inc. to be defective.

No representative, distributor, or dealer has the authority to make any promise, agreement, oralteration of this return policy.

5

Return Policy

Authorization - An authorization number must be obtained before returning any merchandise.

Handling and Restocking Charges - A minimum handling and restocking charge of 15% maybe charged on all returned merchandise.

Reconditioning - Any reconditioning cost will be deducted from the credit.

1 Year Limit - All merchandise returned for credit must have been purchased within the yearprevious to the time of the return.

Special Made Items - Return credit for special made product will vary depending on theproduct.

Proof Of Purchase - Only items originally purchased from OTR Wheel Engineering will beconsidered for return.

Account Credit -All credits will be credited to the customers account, unless otherarrangements were made at the time authorization was obtained.

Prepaid Shipments - All returns that are returned via common carrier must be prepaid.

6

Definitions and ExplanationsBead Seat - Position where the tire restson the inside of the rim and seals.

Bolt Circle - The diameter at which boltholes are located for mounting purposes.

Bolt Pattern - The mounting patternincluding the number of bolt holes, the boltcircle and the pilot hole diameter.

Capacity - Load rating given to a wheel.Based on a single wheel application.Capacities are based on applicable SAEstandards.

Center Line - One half the rim width.

Chamfer - Breaks in the sharp edges of themounting bolt holes to assist in assembly.

Drop Center - The inside diameter of therim where the center disc is normallywelded to the rim. Also referred to as therim well or deep well.

Inset/Outset - Inset is positive offset, inwhich the center line of the wheel isinboard from the mounting face of the disc.Outset is negative offset, in which thecenter line of the wheel is located outboardfrom the mounting face of the disc.

Non-reversible Wheel - A wheel that willmount with one side of the disc face only.

Pilot Hole - Nominal diameter of the centerhole that fits over the hub or axle.

Reversible Wheel - A wheel that can bemounted with either side of the disc face tothe hub face.

Rim Diameter - Nominal diametermeasured from the bead seat.

Rim Flange - The edge of the rim that hasa larger diameter than the tire beaddesigned to support the tire.

Rim Profile - The rim shape as defined bythe Tire and Rim Association.

Rim Width - Nominal width measuredbetween rim flanges.

SAE - Society of Automotive Engineers.When a wheel conforms to published SAEspecifications, it is assigned a number.

Tubeless Wheel or Rim - A single piecewheel or rim with a drop center (rim well)designed for use with tubeless tires.

Valve Guard - Device on the wheel toprotect the valve stem.

Valve Hole - A round hole in a single piecerim to accommodate the valve stem.

Weight Holes - Additional holes placed inthe disc for the attachment of wheelweights.

Wheel - A rim combined with a center discwhich has bolt holes for attaching to avehicle.

7

The following explanations reference the above illustration.

Bolt Circle Diameter - The diameter of the Bolt Circle is the most important factor for correctlyguiding the disk onto the hub.

Pilot Hole - The diameter of the Pilot Hole may be classified into the following two categories;

A. For hubs with flat-based wheel nuts, the Pilot Hole should have a plus tolerance of afew tenths of a mm. The Pilot hole should both support the wheel and guide itcorrectly onto the hub. If the gap between the hub and the disc is too large, the discwill not center on the hub and the vehicle will rock while in motion, greatly increasingthe risk of the wheel nuts coming loose.

B. For applications with tapered or rounded wheel nuts, the plus tolerance of the PilotHole can vary between one or two mm. Countersinks in the bolt holes should fit thenuts shape correctly, as the nuts are supposed to center the disc. Incorrectcountersinks may cause wheel nuts to come loose.

The Number of Bolt Holes - The estimated weight bearing capacity for the axle determines thenumber of studs required. The stud size is equally important. These parameters aredetermined by the axle manufacturer.

8

Bolt Hole Diameter - The Bolt Hole Diameter is determined by the size and number of boltholes, and the shape of the countersinking.

Chamfer’s or Countersinks - The interface between the wheel nut and the disc can be “flat”,“conical” or “spherical”. The latter two shapes guide the disc, and to some extent locks thenuts as they are tightened. Wheels with chamfers on both sides can be turned to eitherside, using the same wheel to provide different track widths.

9

Note: Please note that “-Offset” is alsoknown as “Outset” and “+ Offset” is alsoknown as “Inset”.

Offsets refer to the placement of the centerdisc inside the rim. The offset is whatdetermines the track width of the tires andwheels on the vehicle.

A “center line” offset means the mountingface of the disc is located exactly on thecenter line of the rim.

- Offset means the disc is mounted off centerline towards the vehicle. This positionswidens the wheel track width (see theillustration to the right).

+ Offset means the disc is mounted offcenter line away from the vehicle. Thisposition narrows the wheel track (again, seethe illustration to the right).

Measurements should always be based onthe distance of the mounting face of the discfrom the center line of the rim.

10

How to Measure a Wheel

In order to help us, HELP YOU THE CUSTOMER, get the correct wheel for your machine orapplication, we need to get the correct information from you about the wheel you require.You can either write this information down on a piece of paper or use the Wheel ApplicationData Sheet located a few pages behind this one.

Step 1 - Do you have the Original Equipment Manufacturer’s or the wheelmanufacturer’s part number for the wheel?

• If you have any of those numbers, call our customer service staff to see if we may be ableto cross reference the information in the database of part numbers we already have. If wedon’t have it in our database already, we will want to add it with the other informationcollected. If none of these numbers are available, proceed to step 2.

Step 2 - What is the specific tire size you are using?

• The tire size will tell us the proper rim diameter and width required. The size of the tiremay also help us determine the correct rim profile to use. In certain cases it won’t and wewill need you to help us identify the profile from the rims shown in this catalog. Anextensive table is located in the back of this catalog for locating the tire size and theproper rim size.

• In most cases, steps 1 and 2 will give us the information we need to make sure weare providing you with the correct wheel for your machine.

Step 3 - How many bolt holes are there?

• Simply count the number of holes in the disc for the wheel studs. We also need to know ifthe holes are equally spaced or not. If in doubt, just measure the distance between a fewof the holes to see.

Step 4 - What is the Bolt Circle size?

• How you correctly measure the Bolt Circle depends on how many holes are in the disc. Ifthe disc has an even number of holes and they are equally spaced, the illustration on thenext page shows you how to measure the dimensions easily.

12

• Use a tape measure or a straight edge and measure the holes as shown in the illustration. Whenmeasuring the Bolt Circle, you want to measure from the top edge of the hole at one end to thetop edge of the hole on the other end. You want to be as exact as possible in yourmeasurements. The following is a listing of standard bolt patterns used in many agriculturalwheels. You may find your measurements are one of these patterns. In a few cases, you mayhave an odd pattern that is not standard.

Holes BC BC Pilot Hole Pilot Hole(Inches) (Decimal) (Inches) (Decimal)

4 4” 4.000 2-1/2” 2.500

4 5” 5.000 3-5/8” 3.625

5 4-1/2” 4.500 3-1/8” 3.130

5 5-1/2” 5.500 4” 4.000

6 6” 6.000 4-5/8” 4.625

6 8-3/4” 8.750 6-15/32” 6.469

8 6-1/2” 6.500 4-3/4” 4.750

8 8” 8.000 6” 6.000

8 10-3/16” 10.188 8-3/4” 8.750

9 9-1/2” 9.500 7-3/4” 7.750

10 11-1/4” 11.250 8-3/4” 8.750

10 12” 12.000 9-1/2” 9.500

10 13-3/16” 13.188 11-1/17” 11.059

10 20-1/8” 20.125 17-7/8” 17.875

10 22-1/4” 22.250 20-1/8” 20.125

12 16-5/8” 16.625 14-1/2” 14.500

14 12” 12.000 9-1/2” 9.500

• Odd numbered bolt holes are the only real difficult bolt patterns to measure because they requirefour separate measurements and a little math. Reference the illustration for the 5 hole pattern,measure dimension A, B, C and D. Plug those numbers into the formula A+B+C+D = Bolt Circle,and you have the correct dimension for the odd numbered bolt holes. Note: This only works whenthe holes are equally spaced. If the bolt holes are grouped (ie. 2 holes, a space, 2 more holes, aspace, this will require that you send the wheel to one of our facilities to be measured by ourtechnical staff to make sure we have the correct pattern information.

• Measure the Inside Diameter (ID) of the Pilot Hole as shown in the illustration on page 7.• Remember that for hubs with flat-based wheel nuts, the Pilot Hole should have a plus tolerance of

a few tenths of a mm. The Pilot hole should both support the wheel and guide it correctly onto thehub. If the gap between the hub and the disc is too large, the disc will not center on the hub andthe vehicle will rock while in motion, greatly increasing the risk of the wheel nuts coming loose.For applications with tapered or rounded wheel nuts, the plus tolerance of the Pilot Hole can varybetween one or two mm. Countersinks in the bolt holes should fit the nuts shape correctly, as thenuts are supposed to center the disc. Incorrect countersinks may cause wheel nuts to comeloose.

13

Step 5 - Are the bolt holes chamfered or are they straight?

• If the bolt holes are straight, that means you are using a “flange wheel nut” to secure thewheel to the hub. If the bolt holes have a chamfer, we need to know if it is spherical orconical. We also need to know if the chamfer is only on one side or both.

• If the holes are chamfered, you could give us the nut information and we can translatethat into the correct chamfer information.

• If you don’t have the nut information, you will have to measure the chamfer widths anddepths. Reference the illustration on Page 8.

• If necessary, you can send us a wheel nut to make sure we get it exact.

Step 6 - What is the wheel offset?

• You will need to take a measurement for the “Back Spacing” which we will translate intothe correct offset for the wheel. Reference the illustration below for measuring the backspacing. You need to take the wheel and lay it down so the machine side of the wheel isfacing up.

• The Back Spacing dimension is the distance from the extreme back edge of the rim, notthe bead seat, to the mounting pad of the disc. Lay a straight edge across the back edgeof the rim and measure down to the mounting pad. Nearly all custom wheels use thismeasurement method to indicate the location of the mounting pad in relation to the rim.We can use this dimension to calculate the actual Inset or Outset measurement for thewheel.

Step 7 - What kind of disc is being used in the wheel?

• The disc can be either a flat plate or formed disc. Nearly all agricultural wheels aremanufactured with a formed disc. A formed disc is usually pushed into the center of therim with a press and then welded in place. The disc usually has a leg width greater thanthe disc thickness. This leg provides greater support and disperses the load stress over awider area of the rim center than would a flate plate disc welded in the center.

14

• Several of the possible disc profiles are pictured in the illustrations above. Discs cancome in several different thicknesses and diameters for the different rim sizes that areused.

• You should be able to easily identify the disc type in the wheel you have from theillustrations above. Just let your customer service person know which one you require.

Step 8 - Where is the valve hole located in the rim and what kind of valve hole is it?And does it have a valve guard?

• One piece rims will have a valve hole which can be located in many different locations inthe rim. Depending on the profile and size of the rim, the valve hole could be located inone or two of these locations. Reference the illustrations below and on the next page.

15˚ RimsNon Demountable

Small DropCenter Rims

15

• The small drop center rims shown in the illustrations on the previous page show thepossible locations for 4 different valve holes. H1 shows a valve hole that has beenembossed into the rim. H3 shows a valve hole with no embossment and is mechanicallypunched into the rim.

• The 15˚ rim illustrated in the center shows four possible locations for a valve hole. • The illustration at the top of the page for the DW rim shows the location for two possible

locations for a valve hole. One of those locations shows a valve guard. In the case of theDW rim, nearly all of the rims will come with two valve holes located as shown above.

• There are various different kinds of valve guards available and in use today. Referencethe illustrations below.

Figure A Figure B Figure C Figure D

Figure E Figure F Figure G Figure H

Figure I Figure J

Valve Guard Illustrations

DW Rim

VH VH

16

Step 9 - Are there any other items on the wheel not already described such as beadreinforcements, etc.?

• Bead reinforcements are used in rough duty applications such as forestry or heavy loadapplications such as grain carts. There are various kinds of bead reinforcements in useother than the ones shown in the illustration at the top of page 15.

• Does your rim have bead humps? Reference the illustration below. Bead humps areformed into the rim when it is rolled. The purpose of the bead humps is to lock the tirebead into the bead area of the rim should air pressure run low or if you get a flat. This isintended to keep the tire from easily dislodging itself from the rim bead area.

Step 10 - What color paint do you want? Do you want your wheel primer coated? Doyou want any special rust preventative treatments such as Ecoat, epoxy primer or zincoxide?

• You have three options for primer and rust/corrosion prevention. 1) Epoxy primer is a standard under coat that provides a minimum of rust and corrosion

prevention. 2) Ecoat provides a medium amount of rust and corrosion prevention (up to 600 hours

of salt spray protection).3) Zinc oxide provides the maximum amount of rust and corrosion prevention (up to

6000 hours of salt spray protection).• The standard paint colors available are white, off-white, yellow, orange, silver or black.

Wheel pictured with bead humps Close up view of bead hump and how the tire fits

17

BOLT

TIRE

PILOT HOLE DIAMETER

CENTER THICKNESS

CENTER

keith.heeres

Text Box

15 degree

18

Custom Built Wheels

OTR Wheel Engineering has the capability to build nearly any kind of wheel for off roadapplications. When a wheel is manufactured according to the customers specifications, ALLSALES ARE FINAL. OTR Wheel Engineering warrants the wheel for defects according to ourWarranty Statement.

19

Packaging and Handling

1. Unless otherwise noted on your bill of lading and invoice, all shipments are made onNON-RETURNABLE pallets.

2. All shipments are made freight collect unless prepaid freight arrangments have been madein advance.

3. Depending on the sizes and quantities of the wheels or rims being shipped, shipments canbe made loose, boxed, palletized and shrink wrapped, and palletized and banded.

4. We can utilize your carrier of choice or one of our preferred carriers. We use a host ofcommon carriers for Less Than a truck Load (LTL) shipments as well as full truck loads.

5. We utilize package delivery services such as the U.S. Mail, UPS, Federal Express, andDHL.

6. For export orders, we can load your shipping containers at our loading dock.

7. Any special packaging requirements for your order needs to be communicated to thecustomer service representative handling your account.

20

Important Notice

There are thousands of part numbers and specifications for all of the wheel and rim productsin production today. If you can provide us with the manufacturers part number or theinformation from the previous section on “How to Measure a Wheel”, we will be able locatethe correct item for you. This catalog includes numerous illustrations and drawings whichshould assist you in helping us identify the correct item. If something is missing that youbelieve we should add to our catalog, please let us know so we can improve our catalog tomake it easier for you to purchase from us.

We have included several part numbers for many of the commonly found wheel and rimproducts used on modern agricultural equipment. Contact our sales staff for information wehave available on your antique tractor equipment as well.

If necessary, you can use the “Tire to Rim Tables” located in the Appendixes in the back ofthis catalog to locate the proper rim size.

21

Small Agricultural Wheels12” Dia. to 20” Dia.

For the purposes of organizing the products described in this catalog, wheel and rimdiameters from 12” to 20” are classified as Small Agricultural Wheels. Wheels in thisclassification of products are used on tractors, trailers, implements, light trucks, skid steers,and other multi-purpose vehicles and equipment.

Sizes Available15.5 x 8 16.5 x 9.75 19.5 x 12.2515.5 x 13 17.5 x 8.25 19.5 x 13.0016.5 x 6.00 17.5 x 10.5 19.5 x 14.0016.5 x 6.75 17.5 x 11.75 19.5 x 15.0016.5 x 8.25 19.5 x 11.75

Sizes Available16 x W8L 16.1 x W16C 20 x W1116 x W8H 16.1 x W18C 20 x W14L16 x W10L 20 x W7B16 x W10H 20xW7L16.1 x W11C 20 x WH7B16.1 x W14C 20 x W8B

Sizes Available12 x 2.50 15 x 4.5 KB 16 x 4.5012 x 3.00 15 x 4J 16 x 5.5012 x 4JA 15 x 5K 16 x 6LB12 x 5JA 15 x 5KB 16 x 812 x 7JA 15 x 6LB 16 x 8LB12 x 8.5JA 15 x 7JA 16 x1013 x 4.5J 15 x 8LB 16 x 10LB14 x 5KB 15 x 10 18 x 5.5014 x 6KB 15 x 10LB 19 x 3.0014 x 8KB 15 x 13LB 20 x 5.5015 x 3.00 16 x 4.00 20 x 7.5DT LB15 x 4.5K 16 x 4.25

Rim Profile designations - C, D, E, F, JA, KA

Rim Profile designations - B, E, J,JK, JJ, K, KB, L, LB, and T

W Style Rim

15˚ Single Piece

22

The following table contains a listing of bolt patterns that may commonly be found on smallagricultural wheels.


4 5” 5.000 3-5/8” 3.625

5 5-1/2” 5.500 4” 4.000

6 6” 6.000 4-5/8” 4.625

6 8-3/4” 8.750 6-15/32” 6.469

8 6-1/2” 6.500 4-3/4” 4.750

8 8” 8.000 6” 6.000

8 8” 8.000 6” 6.000

8 10-3/16” 10.188 8-3/4” 8.750

9 9-1/2” 9.500 7-3/4” 7.750

Wheel disc profiles available are as shown below

Small wheel examples

23

The following pages contain a numerical listing of all the wheels assigned Society ofAutomotive Engineers (SAE) wheel numbers and their specifications. These are standardwheel designs that are commonly called for in many small wheel agricultural applications.

SAE/ Wheel Size Description Part Number Offset Load CapacityASAENO.401 14 x 5KB 4 Hole, 5.00 BC, 3.62 PH 105560 0.38 Outset 1250

402 14 x 6KB 4 Hole, 5.00 BC, 3.62 PH 105561 0.38 Outset 1250

403 15 x 4J 4 Hole, 5.00 BC, 3.62 PH 103638 0.44 Outset 1250

404 15 x 4.50KB 4 Hole, 5.00 BC, 3,62 PH 103639 0.38 Outset 1250




554 15 x 5K 5 Hole, 5.50 BC, 4.00 PH 102597 0.12 Outset 2300

555 15 x 6L 5 Hole, 5.50 BC, 4.00 PH 103741 0.25 Outset 2300

556 15 x 8LB 5 Hole, 5.50 BC, 4.00 PH 106482 0.25 Outset 2300

601 14 x 5KB 6 Hole, 6.00 BC, 4.62 PH 105392 1.12 Inset 1800

603 14 x 5KB 6 Hole, 6.00 BC, 4,62 PH 105394 1.12 Inset 2500



610 15 x 5K 6 Hole, 6.00 BC, 4.62 PH 102131 1.12 Inset 2200

612 15 x 6L 6 Hole, 6.00 BC, 4.62 PH 102457 1.12 Inset 2200

614 15 x 6LB 6 Hole, 6.00 BC, 4.62 PH 108790 1.12 Inset 2800

616 15 x 6LBH 6 Hole, 6.00 BC, 4.62 PH 106533 1.12 Inset 3500

617 16 x 4.00E 6 Hole, 6.00 BC, 4.62 PH 106626 1.12 Inset 2000

619 16 x 4.50E 6 Hole, 6.00 BC, 4.62 PH 105294 1.12 Inset 2300

621 16 x 4.50EH 6 Hole, 6.00 BC, 4.62 PH 105377 1.12 Inset 2500

623 16 x 5.50F 6 Hole, 6.00 BC, 4.62 PH 105295 1.12 Inset 2800


625 16 x 6LB 6 Hole, 6.00 BC, 4.62 PH 105748 1.12 Inset 2800

628 18 x 5 50F 6 Hole, 6.00 BC, 4.62 PH 106966 1.12 Inset 2600

SAE Wheels List

24

SAE/ Wheel Size Description Part Number Offset Load CapacityASAENO.630 20 x 5.50F 6 Hole, 6.00 BC, 4.62 PH 106955 1.12 Inset 2800






641 16 x W8L 6 Hole, 6.00 BC, 4.62 PH 106819 1.12 Inset 2800




647 16.1 x W11C 6 Hole, 6.00 BC, 4.62 PH 106980 1.12 Inset 2800

648 16.1 x W11C 6 Hole, 6.00 BC, 4,62 PH 106931 1.12 Inset 3500


650 20 x W7B 6 Hole, 6.00 BC, 4.62 PH 106957 1.12 Inset 2800





25

More commonly used small agricultural wheelsSorted by Description, wheel size and tire size.

Wheel Size Description Part Number Offset Load Capacity14 x 8KB 4 Hole, 5.00 BC, 3.62 PH 106782 0.38 Outset 1250

14 x 8KB 6 Hole, 6.00 BC, 4.62 PH 106783 1.12 Inset 1800

15 x 10LB 5 Hole, 5.50 BC, 4.00 PH 0416589 0.25 Outet 2300

15 x 10LBH 8 Hole, 8.00 BC, 6.00 PH 107173 1.12 Inset 5700

15 x 10LBH 8 Hole, 8.00 BC, 6.00 PH 107502 1.50 Outset 5700


15 x 5KB 4 Hole, 5.00 BC, 3.62 PH 105831 0.38 Outset 1250

15 x 5KB 6 Hole, 6.00 BC, 4.62 PH 107936 1.12 Inset 2200

15 x 6L 4 Hole, 5.00 BC, 3.62 PH 104072 0.38 Outset 1250



15 x 7JA 6 Hole, 6.00 BC, 4.62 PH 107747 1.12 Inset 2200

15 x 8LB 4 Hole, 5.00 BC, 3.62 PH 106781 0.38 Outset 1250




16 x 5.50F 5 Hole, 5.50 BC, 4.00 PH 100550 0.62 Outset 2000

16 x 5.50F 8 Hole, 8.00 BC, 6.00 PH 106877 1.12 Inset 3500

16 x 5.50F 8 Hole, 8.00 BC, 6.00 PH 0416568 1.56 Inset 3500

16 x 6LB 8 Hole, 8.00 BC, 6.00 PH 107499 1.12 Inset 3500

16 x 6LB 6 Hole, 6.00 BC, 4.62 PH 0412473 1.12 Inset 1800

16 x W10L 8 Hole, 8.00 BC, 6.00 PH 106939 1.12 Inset 5700


16 x W10L 8 Hole, 8.00 BC, 6.00 PH 0415973 1.50 Outset 6000


16 x W8L 8 Hole, 8.00 BC, 6.00 PH 106945 1.50 Outset 5000

16.1 x W11C 8 Hole, 8.00 BC, 6.00 PH 106870 1.12 Inset 5700


16.1 x W11C 8 Hole, 8.00 BC, 6.00 PH 504830 1.50 Outset 6000

26

Wheel Size Description Part Number Offset Load Capacity16.1 x W14C 8 Hole, 8.00 BC, 6.00 PH 108182 0.38 Inset 6000


16.1 x W14C 8 Hole, 8.00 BC, 6.00 PH 108191 1.50 Outet 6000













16.1 x W18C 8 Hole, 10.826 BC, 8.715 PH 108529 0.0 Offset 10000


16.5 x 8.25 8 Hole, 8.00 BC, 6.00 PH 107235 0.38 Inset 6000

16.5 x 8.25 8 Hole, 8.00 BC, 6.00 PH 107523 1.12 Inset 6000

16.5 x 8.25 6 Hole, 6.00 BC, 4.62 PH 107254 1.06 Inset 3800

16.5 x 8.25 8 Hole, 8.00 BC, 6.00 PH 0419355** 1.50 Outset 6000

16.5 x 9.75 8 Hole, 8.00 BC, 6.00 PH 107187 1.12 Inset 6000

16.5 x 9.75 8 Hole, 8.00 BC, 6.00 PH 107188 0.38 Inset 6000

16.5 x 9.75 8 Hole, 8.00 BC, 6.00 PH 108186 1.50 Outset 6000

16.5 x 9.75 6 Hole, 6.00 BC, 4.62 PH 107460 1.12 Inset 3800

16H x W8L 8 Hole, 8.00 BC, 6.00 PH 106897 0.25 Outset 5700

16H x W8L 8 Hole, 8.00 BC, 6.00 PH 106938 1.12 Inset 5700


16H x W8L 6 Hole, 6.00 BC, 4.62 PH 107163 1.12 Inset 3500

20 x W8B 8 Hole, 8.00 BC, 6.00 PH 107262 0.38 Inset 6000

20 x W8B 8 Hole, 8.00 BC, 6.00 PH 107474 1.50 Outset 6000

20 x W8B 8 Hole, 8.00 BC, 6.00 PH 107489 1.12 Inset 6000

20H x W7B 8 Hole, 8.00 BC, 6.00 PH 107127 1.50 Outset 6000

27

Wheel Size Description Part Number Offset Load Capacity20H x W7B 8 Hole, 8.00 BC, 6.00 PH 107261 1.12 Inset 6000

20H x W7B 8 Hole, 8.00 BC, 6.00 PH 107404 0.38 Inset 6000


20H x W7L 6 Hole, 6.00 BC,4.62 PH 107272 1.12 Inset 2800

28

Large Agricultural Wheels - Single Piece22.5” Dia. to 54” Dia.

For the purposes of organizing the products described in this catalog, wheel and rimdiameters from 22.5” to 54” diameter are classified as Large Agricultural Wheels. Wheels inthis classification of products are used on tractors, grain carts, combines, self propelledforage harvestors, high clearance row crop sprayers, and other multi-purpose vehicles andequipment.

Sizes Available22.5 x 8.25 22.5 x 16 26.5 x 2422.5 x 9 22.5 x 20 26.5 x 2822.5 x 11.25 22.5 x 24 30.5 x 2022.5 x 12.25 24.5 x 8.25 30.5 x 2422.5 x 13 26.5 x 13 30.5 x 2822.5 x 14 26.5 x 1622.5 x 15 26.5 x 20

Sizes Available32 x DH21 38 x DD1632 x DH27 38 x DD1832 x DH31 42 x DD1632 x DH36 42 x DD1832 x DH44 46 x DD16

Sizes Available24 x DW16L 30 x DW14A 32 x DW44A 34 x DW28 38 x DW28 46 x DW13A24 x DW18L 30 x DW16A 34 x DW14A 38 x DW14A 42 x DW16A 46 x DW16A26 x DW12A 30 x DW20A 34 x DW16A 38 x DW15A 42 x DW18A 50 x DW10A26 x DW16A 32 x DW21A 34 x DW20A 38 x DW16A 42 x DW20A26 x DW20A 32 x DW27A 34 x DW21A 38 x DW18A 42 x DW2426 x DW25A 32 x DW31A 34 x DW23A 38 x DW20 42 x DW2828 x DW18L 32 x DW36A 34 x DW24 38 x DW24 46 x DW10A

DD and DH Style Rim

15˚ Single Piece

29

MW style rims share a profile nearly identicalto the DW style rims. The difference in therims is the MW style rims have a shallowerintermediate well and deep well than the DWstyle rims. The MW rims are also made froma slightly heavier material. The MW rim wasdeveloped to utilize the wide variety of discsmanufactured for use on W style rims.

Sizes Available34 x MW20A 42 x MW20A34 x MW23A 42 x MW28A34 x MW23A

Sizes Available30 x DWW14 34 x DWW23A 38 x DWW1532 x DWW21A 38 x DWL18 38 x DWW1632 x DWW27A 38 x DWW12 42 x DWW1834 x DWW21A 38 x DWW14

Sizes Available24 x W6 26 x W15L 30 x W15L 36 x W12 46 x W12A24 x W7 28 x W7 30 x W16L 38 x W10 46 x W1324 x W8 28 x W8 30 x W20L 38 x W11 46 x W13A24 x W8H 28 x W9 32 x W10 38 x W12 46 x W16A24 x W9 28 x W10H 32 x W11 38 x W14L 46 x W16L24 x W10 28 x W11 34 x W10 38 x W15L 46 x W18A24 x W10H 28 x W12 34 x W14L 38 x W16L 48 x W724 x W11 28 x W13 34 x W15L 38 x W18L 48 x W824 x W12 28 x W14L 34 x W16L 42 x W16A 46 x W18L24 x W13 28 x W15L 34 x W18L 42 x W18L 48 x W1024 x W14L 28 x W16L 36 x W7 44 x W7 50 x W1024 x W15L 28 x W18L 36 x W8 44 x W8 54 x W10A24 x W16L 30 x W13 36 x W10 46 x W1026 x W12 30 x W14L 36 x W11 46 x W12

DWW Style Rim Base


8 8” 8.000 6” 6.000

8 10-3/16” 10.188 8-3/4” 8.750

9 9-1/2” 9.500 7-3/4” 7.750

10 11-1/4” 11.250 8-3/4” 8.750

10 12” 12.000 9-1/2” 9.500

10 13-3/16” 13.188 11-1/17” 11.059

10 20-1/8” 20.125 17-7/8” 17.875

10 22-1/4” 20.250 20-1/8” 20.125

12 16-5/8” 16.625 14-1/2” 14.500

14 12” 12.000 9-1/2” 9.500

30

32” VA Style Rims

The VA style rims are three piece (multipiece)rim assemblies. These rims come in sizes thatinclude two different flange heights (dimension“C” in the illustration above) - either 1.7” or1.125”. The rims are assembled in thefollowing sizes:

The table to the leftshows a list of commonbolt patterns found inlarge diameter wheelsused in agriculturalapplications.

Wheel disc profiles available are as shown below

Sizes Available32 x 27 32 x 4432 x 31 32 x 4932 x 36 32 x 5332 x 41 32 x 59

31

Large Agricultural Wheels - Waffle Wheels24” Dia. to 38” Dia.

The “Waffle” disc and rim permits assembly from either side allowing the disc to be reversedon each side to provide 4 different offsets. The assembly can be mounted with either discface to the hub in each of the disc assembly positions which provide a total of 8 offsets.

The Waffle Ring is a formed flanged which is press-fitted and welded into the rim to combinethe strength of the Waffle with the strength of the rim to provide an integral unit which is aextremely strong manually adjustable wheel.

Waffle wheels are available in varying sizes and bolt patterns. Ask your sales person toassist you in locating the correct wheel for your tractor or machine.

Sizes Available24 x W12 34 x W1024 x W15 34 x W1326 x W12 34 x W1526 x W15 38 x W1028 x W10 38 x W1228 x W12 38 x W1528 x W15 38 x W1828 x W18 42 x DD01630 x DWW13 42 x DD01830 x DWW15 54 x W10

32

Waffle Wheel RimsPart Rim Dia. Rim Width Profile Rim Mat. Well ID Well Rim Waffle

Number Thickness Width BC05-10215-00 24 12 WH 0.171 22.084 8.25 19.25

05-10448-00 24 15 W 0.187 22.084 10.75 19.25

05-09426-00 26 12 WH 0.171 24.084 8.25 21.25

05-09425-00 26 15 W 0.187 24.084 10.75 21.25

05-09425-01 26 15 W 0.187 24.084 10.75 21.25

05-12210-00 26 15 W 0.187 24.084 10.75 21.25

05-10214-00 28 10 WH 0.171 26.084 6.25 23.25

05-09435-00 28 12 WH 0.171 26.084 8.25 23.25

05-09435-01 28 12 WH 0.171 26.084 8.25 23.25

05-13972-00 28 12 W 0.171 26.084 8.25 23.25

05-09434-00 28 15 W 0.187 26.084 10.75 23.25

05-09434-01 28 15 W 0.187 26.084 10.75 23.25

05-12847-00 28 15 W 0.187 26.084 10.75 23.25

05-10309-00 28 18 DW 0.224 25.139 2.83 23.25

05-12386-00 28 18 W 0.224 25.139 2.83 23.25

05-12444-00 28 18 W 0.224 25.139 2.83 23.25

05-13970-00 28 18 W 0.224 25.139 2.83 23.25

05-09668-00 30 13 DWW 0.187 26.084 23.25

05-09668-01 30 13 DWW 0.187 26.084 23.25

05-13973-00 30 13 DWW 0.187 26.084 23.25

05-09669-00 30 15 DWW 0.187 26.084 6.50 23.25

05-09669-01 30 15 DWW 0.187 26.084 6.50 23.25

05-10693-00 30 15 DWW 0.187 26.084 23.25

05-12449-00 30 15 DWW 0.224 26.084 5.12 23.25

05-12449-01 30 15 DWW 0.224 26.084 5.12 23.25

05-13974-00 30 15 DWW 0.187 26.084 5.12 23.25

05-10346-00 34 15 W 0.187 32.084 10.25 29.25

05-13099-00 38 10 WH 0.187 36.084 33.25

05-10425-00 38 12 W 0.171 36.084 33.25

05-10426-00 38 15 W 0.187 36.084 10.75 33.25

05-11726-00 38 18 W .229 36.084 12.94 33.25

05-11728-00 42 16 DD .229 36.084 7.25 33.25

05-11729-00 42 18 DD .229 36.084 33.25

05-12681-00 54 10 W .276 52.084 5.61 33.25

33

Waffle Wheel DiscsPart Fits Rim Disc Bolt Bolt Circle Disc. Mat. Bolt Hole Disc Draw Waffle Bolt

Number Dia. Type Holes Dia. Thickness Nom Dia. Circle

05-10211-00 24 FC 8 10.827 0.375 0.843 4 19.25

05-10831-00 24 Flat 10 13.189 0.375 0.906 None 19.25

05-10212-00 26 FC 8 10.827 0.375 0.843 4 21.25

05-09423-00 26 FC 10 13.189 0.375 0.906 4 21.25

05-09452-00 26 FC 10 13.189 0.375 0.906 2.85 21.25

05-10116-00 26 Flat 12 16.732 0.375 0.906 None 21.25

05-10210-00 28 & 30 FC 8 10.827 0.375 0.843 4 23.25

05-09453-00 28 & 30 FC 10 13.189 0.375 0.906 2.95 23.25

05-09433-00 28 & 30 FC 10 13.189 0.375 0.906 4 23.25

05-10317-00 28 & 30 FC 12 16.732 0.375 0.906 2.95 23.25

05-09988-00 28 & 30 FC 12 16.732 0.375 0.906 4 23.25

05-10213-00 34 FC 8 10.827 0.375 0.843 4 29.25

05-10416-00 34 FC 8 8 0.375 0.687 4 29.25

05-12598-00 34 FC 8 8 0.375 0.843 4 29.25

05-09752-00 34 FC 10 13.189 0.375 0.906 4 29.25

05-10135-00 34 FC 12 16.732 0.375 0.906 4 29.25

05-10423-00 38, 42 & 54 FC 8 10.827 0.375 0.843 4 33.25

05-10990-00 38, 42 & 54 FC 8 10.827 0.5 0.843 4 33.25

05-13744-00 38, 42 & 54 FC 10 13.189 0.472 0.906 4 33.25

34

Large Agricultural Wheels - Rim and Clamp24” Dia. to 38” Dia.

Rim and Clamp wheels are alsoknown as “Manual Adjust” or“Variable Track” wheels. Asshown in the above illustrations,these wheels have a bolted discthat can be removed andfastened to the lugs welded onthe rim in various positions. Thethree factors that determine the8 possible offsets or track widthsare:A = depth of the disc or drawB = width of the lugC = Offset of the lug from rimcenter line

The above illustration shows the 8 possible offsetpositions attainable using the rim and clamp style wheel.Numerous offset combinations are available by changingthe location of the rim clamps in the rim and usingdifferent discs that have varying draws.

35

Clamp Styles

The following illustrations will show the styles of clamps found on agricultural rim and clampdesigns produced by Titan Wheel. There are other clamp styles not shown that are peculiarto rims made by foreign vendors.

Bigfoot Clamp

The Bigfoot Clamp is used on rims that are 26”, 28”, and 30” in diameter. This clamp isidentified in the following tables with a type code “BF”.

Dog Eared Clamp

The Dog Eared Clamp is only used on one rim - the 36 x W9. This clamp is identified in thefollowing tables with a type code “DE”.

36

“O” Style Clamp

The “O” style clamp is used on 24” and28” diameter rims. This clamp isidentified in the following tables with atype code “O”.

“SQ1” Style Clamp

The “SQ1” style clamp is used on 24” to 46” diameter rims. This is probably the mostcommonly found clamp used on agricultural rim & clamp style wheels. This clamp isidentified in the following tables with a type code “SQ1”.

37


The “SQ2” style clamp is used on 24” to 38” diameter rims. This clamp is identified in thefollowing tables with a type code “SQ2”.


The “SQ3” style clamp is used on 24” to 38” diameter rims. This clamp is identified in thefollowing tables with a type code “SQ3”.

38


The “SQ4” style clamp is used on 34” diameter rims. This clamp is identified in the followingtables with a type code “SQ4”.

“U” Style Clamp

The “U” style clamp is used on 34” to 38” diameter rims. This clamp is identified in thefollowing tables with a type code “U”.

39

“Z” Style Clamp

The “Z” style clamp is used on 24” diameter rims. This clamp is identified in the followingtables with a type code “Z”.

40

Rim and Clamp RimsPart Rim Rim Rim # Clamp Rim Rim Clamp Clamps Clamp

Number Dia. Width Profile Clamps Type Mat Well ID Width Bolt Circle Offset04-18747-00 24 7 W 6 SQ1 0.129 22.084 1.84 20.25 0.50

04-19846-00 24 7 W 6 SQ1 0.129 22.084 1.84 20.25 0.50

04-20001-00 24 7 W 6 SQ1 0.129 22.084 1.84 20.25 1.10

04-20275-00 24 7 W 6 SQ1 0.156 22.084 1.84 20.25 0.46

04-18760-00 24 8 W 6 SQ1 0.129 22.084 1.84 20.25 1.21

04-19554-00 24 8 W 6 SQ1 0.129 22.084 1.84 20.25 1.06

04-19563-00 24 8 W 4 SQ3 0.129 22.084 1.84 19.75 2.00

04-19651-00 24 8 W 4 SQ3 0.129 22.084 1.84 19.75 2.00

04-20498-00 24 8 W 6 SQ1 0.129 22.084 1.84 20.25 1.50

05-12754-00 24 8 W 6 SQ1 0.129 22.084 1.84 20.25 1.25

04-19592-00 24 9 W 4 SQ3 0.129 22.084 1.84 19.75 2.00

04-18422-00 24 10 W 6 SQ1 0.129 22.084 1.84 20.25 2.00

04-18763-00 24 10 W 6 SQ1 0.129 22.084 1.84 20.25 1.96

04-19553-00 24 10 W 6 SQ1 0.129 22.084 1.84 20.25 1.06

04-19564-00 24 10 W 4 SQ3 0.129 22.084 1.84 19.75 2.00

04-19650-00 24 10 W 4 SQ3 0.129 22.084 1.84 19.75 2.00

04-20009-00 24 10 W 6 SQ1 0.129 22.084 1.84 20.25 1.20

04-20015-00 24 10 W 6 SQ1 0.129 22.084 1.84 20.25 2.06

04-20256-00 24 10 W 4 Z 0.129 22.084 1.625 20.25

04-20276-00 24 10 W 6 SQ1 0.156 22.084 1.84 20.25 1.90

04-20499-00 24 10 W 6 SQ1 0.129 22.084 1.84 20.25 2.00

04-21143-00 24 10 W 6 SQ1 0.129 22.084 1.84 20.25 0.53

04-21185-00 24 10 W 4 SQ1 0.129 22.084 1.84 20.25 1.89

05-11985-00 24 10 W 8 SQ1 0.129 22.084 1.84 20.25 2.00

04-20236-00 24 11 W 6 SQ1 0.129 22.084 1.84 20.25 1.71

04-20267-00 24 11 W 4 Z 0.156 22.084 1.71 19.803

04-20271-00 24 11 W 4 Z 0.156 22.084 1.71 19.803

04-18421-00 24 12 W 6 SQ1 0.156 22.084 1.84 20.25 2.00

04-18884-00 24 12 W 6 SQ1 0.156 22.084 1.84 20.25 2.00

04-19653-00 24 12 W 8 SQ1 0.156 22.084 1.84 20.25 3.30

04-19697-00 24 12 W 6 SQ1 0.156 22.084 1.84 20.25 2.75

04-19760-00 24 12 W 6 SQ1 0.156 22.084 1.84 20.25 3.29

04-19762-00 24 12 W 6 SQ1 0.156 22.084 1.84 20.25 2.34

04-19877-00 24 12 W 6 SQ1 0.156 22.084 2.00 20.25 2.00

04-20011-00 24 12 W 6 SQ1 0.156 22.084 1.84 20.25 2.06

04-20273-00 24 12 W 6 SQ1 0.156 22.084 1.84 20.25 1.90

04-20535-00 24 12 W 6 SQ1 0.156 22.084 1.84 20.25 0.62

04-11983-00 24 12 W 8 SQ1 0.156 22.084 1.84 20.25 2.00

105431 24 12 W 6 SQ1 0.157 22.084 1.84 20.25 2.00

107160 24 12 W 6 SQ1 0.156 22.084 1.84 20.25 2.00

4-18426-00 24 15 W 6 SQ1 0.187 22.084 1.84 20.25 2.00

41



04-19149-00 24 15 W 8 SQ1 0.187 22.084 1.84 20.25 2.68

04-19546-00 24 15 W 6 O 0.187 22.084 1.84 20.25 2.00

04-19761-00 24 15 W 8 SQ1 0.187 22.084 1.84 20.25 3.29

04-19956-00 24 15 W 8 SQ2 0.187 22.084 2.6 20.25 2.30

04-20000-00 24 15 W 8 SQ1 0.187 22.084 1.84 20.25 0.50

04-20283-00 24 15 W 6 O 0.187 22.084 1.84 20.25 2.00

05-08814-00 24 15 W 4 SQ1 0.187 22.084 1.36 20.25 1.36

05-12743-00 24 15 W 8 SQ1 0.187 22.084 1.84 20.25 3.49

107168 24 15 W 6 SQ1 0.171 22.084 1.84 20.25 3.50

108823 24 15 W 6 SQ1 0.179 22.084 1.84 20.25 2.00

108824 24 15 W 6 SQ1 0.179 22.084 1.84 20.25 1.36

04-18423-00 24 16 W 6 SQ1 0.187 22.084 1.84 20.25 2.00

04-19317-00 26 12 WH 8 SQ1 0.171 24.084 1.84 22.25 2.68

04-19578-00 26 12 WH 6 SQ1 0.171 24.084 1.84 22.25 2.00

04-19838-00 26 12 WH 8 SQ1 0.171 24.084 1.84 22.25 2.31

04-19955-00 26 12 WH 8 SQ2 0.171 24.084 2.6 22.25 2.30

04-20416-00 26 12 WH 8 BF 0.171 24.084 2.3 22.25 2.30

04-20422-00 26 12 WH 8 BF 0.171 24.084 2.3 20.875 2.30

04-18655-00 26 14 DW 6 SQ1 0.187 22.084 1.84 20.25 1.00

04-18425-00 26 15 W 6 SQ1 0.187 24.084 1.84 22.25 2.00

04-19312-00 26 15 W 8 SQ1 0.187 24.084 1.84 22.25 2.68

04-19579-00 26 15 W 6 SQ1 0.187 24.084 1.84 22.25 2.00

04-19736-00 26 15 W 8 SQ1 0.187 24.084 1.84 22.25 2.31

04-19947-00 26 15 W 8 SQ2 0.187 24.084 2.6 22.25 2.30

04-20417-00 26 15 W 8 BF 0.187 24.084 2.3 22.25 2.30

04-20425-00 26 15 W 8 BF 0.187 24.084 2.3 20.875 2.30

04-18433-00 26 16 DW 6 SQ1 0.187 22.084 1.84 20.25 2.00

04-19252-00 26 16 DW 8 SQ1 0.187 22.084 1.84 20.25 2.00

04-18595-00 26 20 DW 6 SQ1 0.187 22.084 1.84 20.25 4.00

04-19560-00 28 9 W 6 SQ1 0.129 26.084 1.84 24.25 1.50

04-19645-00 28 9 W 6 SQ1 0.13 26.084 1.84 24.25 2.00

04-18418-00 28 10 W 6 SQ1 0.129 26.084 1.84 24.25 2.00

04-18419-00 28 10 W 6 SQ1 0.129 26.084 1.84 24.25 2.00

04-20345-00 28 10 W 6 SQ1 0.156 26.084 1.9 24.25 1.90

104094 28 10 W 6 O 0.129 26.084 1.84 24.25 2.00

106825 28 10 W 6 SQ1 0.129 26.084 2 24.25 2.00

04-19043-00 28 11 W 6 SQ1 0.156 26.084 1.84 24.25 2.00

04-20272-00 28 11 W 8 SQ1 0.156 26.084 1.56 24.25 1.56

105049 28 11 W 6 O 0.156 26.084 1.84 24.25 2.00

04-18431-00 28 12 W 6 SQ1 0.171 26.084 1.84 24.25 2.00

42



04-19217-00 28 12 WH 8 SQ1 0.171 26.084 1.84 24.25 2.68

04-19571-00 28 12 W 6 O 0.156 26.084 1.84 24.25 2.00

04-19580-00 28 12 WH 6 SQ1 0.171 26.084 1.84 24.25 2.00

04-19585-00 28 12 WH 6 SQ1 0.171 26.084 1.84 24.25 3.22

04-19738-00 28 12 WH 8 SQ1 0.171 26.084 1.84 24.25 2.31

04-19882-00 28 12 WH 8 SQ2 0.171 26.084 2.6 2.30

04-20414-00 28 12 WH 8 BF 0.171 26.084 2.3 24.25

04-20423-00 28 12 WH 8 BF 0.171 26.084 2.3 22.855 2.30

04-20934-00 28 12 W 6 SQ1 0.171 26.084 1.84 24.25 2.00

05-12738-00 28 12 WH 8 SQ1 0.171 26.084 1.84 24.25 2.00

104204 28 12 W 6 O 0.171 26.084 1.84 24.25 2.00

106464 28 12 W 6 SQ1 0.171 26.084 1.84 2.00

108826 28 12 W 6 SQ1 0.171 26.084 1.84 24.25 2.00

04-19555-00 28 13 W 6 SQ1 0.171 26.084 1.84 24.25 2.00

04-20108-00 28 13 W 8 SQ1 0.171 25.334 3.46

04-18429-00 28 15 W 6 SQ1 0.187 26.084 1.84 24.25 2.00

04-19318-00 28 15 W 8 SQ1 0.187 26.084 1.84 24.25 3.65

04-19581-00 28 15 W 6 SQ1 0.187 26.084 1.84 24.25 2.00

04-19737-00 28 15 W 8 SQ1 0.187 26.084 1.84 24.25 2.31

04-19881-00 28 15 W 8 SQ2 0.187 25.084 2.6 24.25 2.30

04-20418-00 28 15 W 8 BF 0.187 26.084 2.3 24.25 1.00

05-12739-00 28 15 W 8 SQ1 0.187 26.084 1.84 24.25 2.00

05-10694-00 28 18 DW 8 SQ1 0.224 25.139 1.84 24.25 2.34

04-19540-00 30 13 W 8 SQ1 0.187 28.084 1.84 26.25 2.68

04-19837-00 30 13 W 8 SQ1 0.187 28.084 1.84 26.25 2.31

04-19880-00 30 13 WH 8 SQ2 0.187 28.084 2.3 26.25 2.30

04-20424-00 30 13 W 8 BF 0.187 28.084 2.3 24.875

04-18432-00 30 14 DW 6 SQ1 0.187 26.084 1.848 24.25 1.00

04-18658-00 30 15 WH 8 SQ1 0.187 28.084 1.84 26.25 2.00

04-19708-00 30 15 WH 8 SQ1 0.187 28.084 1.84 26.25 2.68

04-19883-00 30 15 WH 8 SQ2 0.187 28.084 2.6 26.25 2.30

04-20027-00 30 15 WH 8 SQ1 0.187 28.084 1.84 26.25 2.31

04-20419-00 30 15 WH 8 BF 0.187 28.084 2.3 26.25

04-20426-00 30 15 WH 8 BF 0.187 28.084 2.3 24.875

04-20427-00 30 15 WH 8 BF 0.187 28.084 2.3 24.875

04-20643-00 30 15 DWW 6 SQ1 0.187 26.084 1.84 24.25 2.00

04-21006-00 30 15 DWW 6 SQ1 0.187 26.084 1.63 24.25 1.63

05-11712-00 30 15 DWW 8 SQ1 0.187 26.084 1.84 24.25 2.00

04-18435-00 30 16 DW 6 SQ1 0.187 26.084 1.84 24.25 2.00

04-19552-00 30 16 DW 6 SQ1 0.187 26.084 1.84 24.25 2.00

43



05-11998-00 34 15 DWW 8 U 0.187 30.084 3.54 28.25 2.00

04-18554-00 34 16 DW 8 SQ1 0.187 30.084 1.84 28.25 2.00

04-20722-00 34 16 DW 8 SQ1 0.187 30.084 1.84 28.25 2.00

04-12702-00 36 9 W 6 DE 0.129 34.084 0.312 31.75

04-19977-00 38 11 W 8 SQ2 0.156 36.084 2.6 34.25 0.78

05-12737-00 38 12 DW 8 SQ1 0.187 34.084 1.84 32.25 2.00

04-18659-00 38 14 DW 8 SQ1 0.187 34.084 1.84 32.25 2.00

04-19976-00 38 14 WH 8 SQ2 0.187 36.084 2.6 34.25 0.78

05-10395-00 38 14 DW 8 U 0.187 34.084 3.54 32.25 2.00

05-10360-00 46 12 W 8 U 0.224 44.084 1.57

05-10624-00 46 12 W 8 U 0.224 44.084 3.46 42.25 1.02

05-11677-00 46 12 W 8 U 0.224 44.084 3.46 42.25 1.56

700000518 46 12 W 8 SQ1 0.229 44.084 1.84 42.125 0.42

44

Rim and Clamp DiscsPart Fits Disc Bolt Bolt Disc B H Chamfer P H Weight 1st Disc Clamp

Number Rim Profile Holes Circle Mat Nom Type Max Holes Locus Draw BCDia. Thck Dia. Data Dia

05-08259-00 24” FC 4 13.189 0.375 0.906 None 5.81 None 16 1.75 20.25

05-08253-00 24” FC 6 6 0.312 0.594 None 4.638 6-11.417 13.75 2.95 20.25

05-02623-00 24” FC 6 6.5 0.224 0.625 90˚ 4.758 4-13.50 8.19 3.89 19.75

05-04674-00 24” FC 8 6 0.375 0.75 90˚ 4.35 None 8 2.00 20.25

05-06326-00 24” FC 8 6 0.5 0.75 90˚ 4.35 4-12.00 8 2.00 20.25

05-12745-00 24” FC 8 7.874 0.375 0.665 None 5.937 3-14.76 10.43 2.06 20.25

05-02849-00 24” FC 8 8 0.224 0.652 90˚ 6.008 4-13.50 9.625 3.89 19.75

05-03275-00 24” FC 8 8 0.224 0.652 90˚ 6.008 4-13.50 9.825 3.89 20.25

05-07855-00 24” FC 8 8 0.224 0.652 90˚ 6.013 4-13.50 9.63 3.89 20.25

05-10616-00 24” FC 8 8 0.375 0.687 None 6.023 4-13.79 10 3.94 20.25

700109102 24” FC 8 8 0.375 0.755 5.937 20.25

05-08851-00 24” FC 8 10.827 0.312 0.826 None 8.755 None 13.75 2.95 20.25

05-09351-00 24” FC 8 10.827 0.375 0.812 None 8.755 None 13.75 2.95 20.25

05-11984-00 24” FC 8 10.827 0.375 0.875 .63R 8.755 None 13.75 3.89 20.25

05-07873-00 24” Flat 10 13.189 0.312 0.812 None 11.09 None None None 20.25

108552 24” FC 10 13.189 0.375 0.906 None 11.068 None 16 1.75 20.25

05-07927-00 26” FC 10 13.189 0.375 0.812 None 11.09 None 16 4.25 22.25

05-08213-00 26” FC 10 13.189 0.375 0.945 None 11.09 None 16 2.16 22.25

108816 26” FC 10 13.189 0.375 0.812 None 11.078 None 16 3.75 22.25

108313 26” FC 10 13.189 0.375 0.906 None 11.078 None 16 1.75 22.25



05-12653-00 28” FC 8 7.874 0.375 0.665 None 5.937 3-14.75 10.43 4.00 24.25

05-02805-00 28” FC 8 8 0.224 0.652 90˚ 6.008 4-16.00 9.62 3.89 24.25

05-07464-00 28” FC 8 8 0.224 0.652 90˚ 6.013 4-16.00 9.62 3.89 24.25

05-07915-00 28” FC 8 8 0.375 1.27 .875R 5.53 3-19.16 10.5 4.00 24.25

05-10617-00 28” FC 8 8 0.375 0.687 None 6.023 4-16.13 10.5 4.00 24.25

05-12596-00 28” FC 8 8 0.375 0.843 5.53 3-14.75 10.43 4.00 24.25

05-09044-00 28” FC 8 10.827 0.312 0.826 None 8.755 None 13.75 2.95 24.25

05-08848-00 28” FC 8 12.992 0.375 0.678 None 11.456 None 16 5.25 24.25

05-08484-00 28” FC 8 15.945 0.375 0.678 None 14.291 None 19 3.01 24.25

05-08198-00 28” FC 10 13.189 0.375 0.945 None 11.09 None 16 2.16 24.25

05-09344-00 28” FC 10 13.189 0.375 0.945 None 11.09 None 16 2.16 22.875

05-07930-00 28” FC 10 13.189 0.375 0.812 None 11.09 None 16 5.25 24.25

108985 28” FC 10 13.189 0.375 0.906 None 11.078 None 16 4.13 24.25

45

Rim and Clamp Disc (continued)Part Fits Disc Bolt Bolt Disc B H Chamfer P H Weight 1st Disc Clamp

Number Rim Profile Holes Circle Mat Nom Type Max Holes Locus Draw BCDia. Thck Dia. Data Dia

05-07552-00 28” FC 10 13.189 0.312 0.812 None 11.09 None 16 4.13 24.25

05-07842-00 28” FC 10 13.189 0.375 0.812 None 11.09 None 16 3.75 24.25

05-08212-00 28” FC 10 13.189 0.375 0.906 None 11.09 None 16 4.13 24.25

108815 28” FC 10 13.189 0.375 0.812 None 11.078 None 16 3.75 24.25

05-09349-00 28” FC 12 16.732 0.375 0.945 None 14.64 None 18.75 3.01 22.875

05-08091-00 28” FC 12 16.732 0.375 0.945 None 14.64 None 19 3.01 24.25

108305 30” FC 8 8 0.224 1.27 .88R 5.53 4-19.00 10.4 4.13 26.25

108434 30” FC 8 8 0.375 1.27 .88R 5.53 6-19.00 10.4 4.13 26.25

05-07961-00 30” FC 10 13.189 0.375 0.812 None 11.05 None 16 5.25 26.25

05-08215-00 30” FC 10 13.189 0.375 0.945 None 11.09 None 16 2.16 26.25

05-09347-00 30” FC 12 16.732 0.375 0.945 None 14.64 None 20 1.75 24.875

05-07541-00 30” FC 12 16.732 0.375 0.945 None 14.64 None 20 1.75 26.25

05-08092-00 30” FC 12 16.732 0.375 0.945 None 14.64 None 19 3.01 26.25

05-11301-00 30” FC 12 16.732 0.375 0.906 None 14.64 None 19 4.00 26.25

05-10294-00 34” FC 8 8 0.438 1.27 .875R 5.53 6-21.75 10.308 4.06 28.25

05-12597-00 34” FC 8 8 0.375 0.843 None 5.53 3-14.75 10.43 4.00 28.25

05-08254-01 34” FC 8 8 0.375 0.687 90˚ 6.045 4-17.00 10 3.89 30.25

05-12652-00 38” FC 8 7.874 0.375 0.665 None 5.937 3-14.75 10.43 4.00 32.25

05-08254-02 38” FC 8 8 0.375 0.687 90˚ 6.045 4-17.00 10 3.89 34.25

05-12751-00 38” FC 8 10.827 0.375 0.875 .63R 8.755 None 13 3.89 32.25

05-08620-01 38” FC 8 10.827 0.5 0.969 8.755 13.75 3.94 32.25

05-10423-00 38” FC 8 10.827 0.375 0.843 None 8.755 6-25.79 13 4.00 33.25

05-10990-00 38” FC 8 10.827 0.5 0.843 None 8.755 6-25.79 13 4.00 33.25

05-08620-02 42” FC 8 10.827 0.5 0.969 8.755 13.75 3.94 38.25

05-10306-00 46” FC 8 8 0.5 1.27 .875 5.53 16.8 5.00 42.25

05-10626-00 46” FC 8 8 0.5 0.812 6.015 3-19.00 13.375 3.94 42.25

05-10122-00 46” FC 10 13.189 0.5 0.906 None 11.09 None 16.8 5.00 42.25

05-10282-00 46” FC 10 13.189 0.5 0.906 None 11.09 None 16.8 5.00 42.25

46

Bevel Mounted Rims24” Dia. to 42” Dia.

Bevel mounted rims are formed with drivers for either “manufacturer specific patterns” or“Universal Mount” patterns. Bevel mounted rims are also called Double Mounted Bevels(DMB) as well as Single Mounted Bevels (SMB). The following table lists all the availablesizes. The sizes noted as “Universal Mount” rims are adaptable to most cast hubs from thevarious manufacturers.

DD Style DMB

DWW Style DMB

W Style DMB

47

Bevel Mounted Rims - Universal MountPart Number Rim Size Number of Rim Mat. Thck Well ID

Drivers05-07578-00 38 x WH12 18 0.187 35.30605-07564-00 38 x WH14 18 0.187 35.33405-10290-00 38 x DD16 26 0.187 32.08405-07565-00 38 x W16 18 0.187 35.33405-08421-00 38 X WH16 20 0.224 35.36102-07470-00 38 X DDW16 26 0.187 31.33405-07566-00 38 X W18 18 0.187 35.33405-07836-00 38 X W18 20 0.187 35.33405-08422-00 38 X WH18 20 0.224 35.36102-07471-00 38 x DDW18 26 0.187 31.33405-10291-00 38 x DDW18 26 0.224 32.08405-10124-00 42 x DDW16 20 0.224 36.08405-10140-900 42 x DDW16 24 0.224 36.08405-10123-00 42 x DDW18 20 0.224 36.08405-10318-00 42 x DDW18 26 0.224 36.084

48

Bevel Mounted Rims Part Number Rim Size Number of Rim Mat. Thck Well ID

Drivers04-13446-00 24 x W12 4 0.171 21.33404-14942-00 24 x W15 8 0.187 21.33404-15095-00 26 x W15 8 0.187 23.33404-14940-00 28 x W12 8 0.171 25.33404-15062-00 28 x W15 8 0.187 25.33404-15096-00 28 x W15 8 0.187 25.33404-13015-00 30 x W12 4 0.171 27.33404-13692-00 30 x W12 4 0.171 27.33405-04271-00 30 x DWW15 8 0.187 25.33404-12890-00 34 x W12 4 0.171 31.33404-12968-00 34 x W14 4 0.187 31.33404-14957-00 34 x W15 8 0.187 31.33404-18095-00 34 x W16 8 0.187 31.33404-17541-00 34 x W18 8 0.187 31.33404-17914-00 34 x W18 12 0.187 31.33404-18096-00 34 x W18 8 0.187 31.33405-09990-00 34 x W20 8 0.187 31.33404-13485-00 36 x W10 4 0.129 33.33404-14207-00 36 x W10 4 0.129 33.33404-13075-00 36 x W11 4 0.156 33.33404-13512-00 36 x W11 4 0.156 33.33404-13999-00 36 x W11 8 0.156 33.33404-13077-00 38 x W10 4 0.129 35.33404-14001-00 38 x W10 8 0.129 35.33404-14208-00 38 x W10 4 0.129 35.33404-12821-00 38 x W11 4 0.156 35.33404-13078-00 38 x W11 4 0.156 35.33404-14210-00 38 x W11 4 0.156 35.33404-16945-00 38 x DWW12 8 0.187 33.33404-12822-00 38 x W12 4 0.171 35.33404-13079-00 38 x W12 4 0.171 35.33404-14947-00 38 x WH12 8 0.187 35.30605-04729-00 38 x DWW14 8 0.187 33.33404-14948-00 38 x WH14 8 0.187 35.33404-16342-00 38 x WH14 8 0.187 35.33404-17515-00 38 x WH14 12 0.187 35.33404-16226-00 38 x W15 8 0.187 35.33404-16743-00 38 x W15 8 0.187 35.33405-10141-00 38 x DDW16 12 0.187 32.084

49

Bevel Mounted RimsPart Number Rim Size Number of Rim Mat. Thck Well ID

Drivers05-10399-00 38 x DDW16 8 0.187 32.08404-16098-00 38 x W16 12 0.187 35.33404-16247-00 38 x W16 8 0.187 35.33404-16504-00 38 x W16 14 0.187 35.33404-17514-00 38 x W16 12 0.187 35.33404-17925-00 38 x W16 12 0.187 35.33404-18164-00 38 x W16 12 0.187 35.33404-19475-00 38 x WH16 14 0.224 35.36105-10377-00 38 x DDW18 8 0.187 32.08404-16966-00 38 x W18 14 0.187 35.33404-17405-00 38 x W18 8 0.187 35.33404-17513-00 38 x W18 12 0.187 35.33404-19329-00 38 x WH18 14 0.224 35.36104-17055-00 42 x W9 8 0.171 39.33405-10374-00 42 x DDW16 12 0.187 36.08405-10376-00 42 x DDW16 20 0.187 36.08404-17291-00 42 x W16 14 0.187 39.33404-19477-00 42 x WH16 14 0.224 39.36105-09068-00 42 x WH16 10 0.224 36.08405-10139-00 42 x DDW18 12 0.187 36.08405-10367-00 42 x DDW18 12 0.224 36.08404-19204-00 42 x WH18 14 0.224 39.361

50

Power Adjust Style Wheels24” DIa. to 38” Dia.

Power Adjust Wheel Sizes AvailableRim Size Number Rail Holes Rim Size Number Rail Holes

of Rails (Parallel or 90˚) of Rails (Parallel or 90˚)24 x W8 5 90˚ 28 x W15L 5 90˚24 x W10 4 Parallel or 90˚ 30 x W14 5 90˚26 x W12 4 Parallel or 90˚ 30 x W14 7 90˚28 x W9 4 90˚ 30 x W15 5 Parallel or 90˚28 x W9 5 90˚ 30 x W20L 5 90˚28 x W10 4 Parallel or 90˚ 34 x W14 6 90˚28 x W10 5 90˚ 34 x W15L 6 90˚28 x W11 4 Parallel or 90˚ 34 x W16L 8 90˚28 x W11 5 90˚ 36 x W11 6 90˚28 x W12 4 Parallel or 90˚ 38 x W11 6 90˚28 x W12 5 Parallel or 90˚ 38 x W12 6 Parallel or 90˚28 x W13 4 Parallel or 90˚ 38 x W14 6 Parallel or 90˚28 x W13 5 Parallel or 90˚ 38 x W15L 6 90˚28 x W14L 4 Parallel or 90˚ 38 x W16L 6 90˚28 x W14L 5 Parallel or 90˚ 38 x W16L 8 90˚28 x W15L 4 Parallel or 90˚ 38 x W18L 8 90˚

Ag Catalog Jan 2008

Documents

Transcript of Ag Catalog Jan 2008